SciCan Hydrim L11w Quick Reference Manual

Hydrim®L110 w Quick Reference Guide

For best results:

Use Stat-Dri Plus rinse aid (part number 8OZPLUS) to prevent spotting.

P0 should be used to keep instruments moist when they will not be washed within one hour.

P1 and P2 should be used to wash instruments in baskets.

P3 and P4 should be used to wash instruments in cassettes and heavily soiled instruments.

Shines when cleaning solution needs changing

Caution:

Flashes when rinse-aid needs filling

1. Hydrim Cleaning Solution is compatible with solid

stainless steel instruments that are resistant to
heat and alkalinity.

2. Carbon steel, aluminum, nickel and rhodium-plated

instruments may corrode in Hydrim Cleaning Solution.
Do not process burrs or endofiles in the Hydrim.

3. Do not process stainless steel and carbon steel

instruments at the same time.

Shines when salt needs refilling

*Actual cycle time will vary depending on

incoming water temperature and pressure

8 min.*
20 min.*
30 min.*
30 min.*
40 min.*

Replacing the Hydrim Cleaning Solution:

When the chemical indicator light shines continuously, and Ed appears on the display, the solution level
is low and the container is in need of replacement.

1. Open the cleaning solution door.

2. Put a new cleaning solution box into the drawer upside down.

3. Te a r o p en the tab.

4a.Pull out the spout and remove the protective cap.

4b.Attach the hose tightly to the connector on the cleaning solution box.

5. Place the box in the cleaning solution drawer and then close.

1

order number 01-108367S

2 5

4a

3

4b

Filter Maintenance:

1. Check the filters daily for debris and

remove if necessary.

2. After undoing the coarse filter, the fine

filter can be removed. Remove any debris
from the filter cavity and rinse the filters
under running water.

3. Insert the filter units and tighten the

coarse filter.

coarse filter

fine filter

lower wash arm upper wash arm

Refilling the Rinse Aid:

When the chemical indicator light
flashes, you will need to refill the
rinse-aid container with Stat-Dri Plus.

1. Fold back the lid of the rinse

aid container.

2. Pour the rinse-aid into the rinse-aid

container until the level indicator
darkens.

3. Close the lid ensuring you that you

hear it snap.

salt container lid

Wash Arm Maintenance:

1. Inspect the nozzles and wash arms

weekly for blocked holes due to debris.

2. Pull the lower arm upwards and lift off.

3. Unscrew the upper wash arm collar

and remove the upper wash arm.

4. Clean both wash arms under

running water.

5. Refit the wash arms. Ensure that the

lower wash arm has locked into place

upper wash
arm collar

chemical indicator light

and the upper one is screwed tight.

level

lid

indicator

rinse-aid containersalt indicator light

Refilling the Water Softener:

If you have set the water softener to any setting above 0,
the SALT indicator flashes when you need to refill the
salt container.

1. Open the salt container lid.

2. Upon first use of the Hydrim L110w, pour approximately

1 litre (1 quart) of water into the salt container. It is not
necessary to add water during subsequent refills of the
salt container.

3. Using the accompanying salt jug, fill the salt container

to the top (maximum of 1kg / 2.2 lbs.)

4. Close the salt container lid.

United States: 1-800-572-1211, Canada: 1-800-870-7777, International: [phone]

Hydrim is a registered trademark of SciCan, Division of Lux & Zwingenberger Ltd.

For all service and repair inquiries:

Email: [e-mail]

P.N.96-108366 Rev. 1.0