Schneider GGBL30202USBAWPWS, GGBL30202USBAS Installation Instructions

Instructions for :

1 and 2 Gang 13A Switch

Socket with USB Charger

GGBL30102USBAS

GGBL30202USBAS
GGBL30102USBA***S
GGBL30202USBA***S

AR1908 Ed B

Read these instructions fully before commencing work and retain

them for future reference.
SAFETY INSTRUCTIONS

These accessories are to be installed in accordance with the current
edition of the IEE Wiring Regulations (BS 7671: Requirements for
Electrical Installations) and appropriate statutory regulations.

In the Republic of Ireland the installation must be in accordance with
the ETCI National Rules for Electrical installations – ET 101.

NOTE: IF YOU ARE IN ANY DOUBT ON HOW TO PROCEED,
CONSULT A QUALIFIED ELECTRICIAN

Switch OFF the mains supply and remove the appropriate fuse or
switch off the appropriate circuit breaker before commencing
installation. Ensure that no one else has access that would enable
the supply to be inadvertently reconnected.

DECORATIVE METAL FRONTPLATES

Lisse

A A

A A

A

SOCKETS WITH SCREWLESS DECORATIVE METAL
FRONTPLATES
Remove the clip-on frontplate by inserting a small screwdriver
alternatively into the small slots (A) on the sides of the frontplate and
gently prise off.

Once the socket is installed replace the screwless frontplate by
clipping it back in place. Do this before reconnecting to the

mains power.

To keep decorative metal frontplates clean, occasionally wipe the
frontplate with a clean soft cloth. Do not use any form of cleaning
agent as this could damage the decorative finish.

2 3

Install the socket as described in the following section, taking
particular care to ensure the socket is correctly earthed. This is
particularly important for accessories with metal frontplates.

Sockets can be installed using wall boxes with a minimum depth as
specified below:

1 gang: 35mm (25mm with mounting spacer supplied)
2 gang 25mm

Always use cable of correct rating and type.
The socket can either be connected to a ring main circuit, in which

case there will be a pair of twin and earth cables entering the box, or
on a spur, which will only have one twin and earth cable entering the
box.

THIS USB CHARGER IS PERMANENTLY CONNECTED
EQUIPMENT. The circuit should therefore incorporate a readily
accessible means for safely isolating the charger when required.

Strip the insulation from the Live and Neutral supply cables and
connect the Brown (or Red) wire(s) to the terminal marked ‘L’ and
connect the Blue (or Black) wire(s) to the terminal marked ‘N’.

Connect the earth wire(s) from the supply cable(s) to the earth
terminal on the rear of the socket, and then connect a short length of
wire from the socket earth terminal to the earth terminal in the wall
box. If the earth wires are bare, they should be sheathed with a

length of green/yellow sleeving.
Ensure all the terminal screws are tightened firmly and are clamped

on the copper conductors of each wire and not on the insulation.
Locate the socket against the wall in front of the wall box, ensuring

that the supply cables are not trapped by the front plate or within the
wall box. Using the fixing screws provided, attach the socket to the
wall box. Ensure the fixing screws are tightened securely.

Replace the appropriate fuse or switch on the appropriate circuit
breaker. Switch on the mains isolator switch.

IMPORTANT NOTICE - WIRING COLOUR CHANGES

As from 1st April 2004 new installations in the UK could be wired
using the new EU Harmonised colours for the supply conductors of
twin and earth cable:

New colours Brown = Live Blue = Neutral
Old Colours Red = Live Black = Neutral

The old colours ceased to be used after 1st April 2006.

Flexible cable colours remain unchanged:

Brown = Live Blue = Neutral

Eire conductor colours for twin and earth cable and
flexible cable:

Brown = Live Blue = Neutral

4 5

WIRING DIAGRAM - 1 gang WIRING DIAGRAM - 2 gang

FROM SUPPLY

LIVE

EARTH

NEUTRAL

FROM SUPPLY

LIVE

EARTH

TO EARTH TERMINAL
IN BACK BOX

NEUTRAL

NOTE

The USB connector is used for charging devices only, such as smart
phones, tablets, cameras etc. When only one device is connected to
a USB connector the total output current of 2.1A is available from
either USB connector and when two devices are connected, the
total rated current of 2.1A is divided between the two USB
connectors.

The USB charging circuit within this device has both short circuit
and overload protection. If the device is overloaded or short-circuit­ed, the electronic circuit will limit or disconnect
the output power to protect against damage or overheating.
Once the fault has been cleared the circuit will re-set and power
on automatically.

Some earlier model mobile phones and devices are not suitable
for direct charging from a USB type charger and may not charge
when connected to this product. These devices will require their own
dedicated charger. Please check with your phone or device supplier
for more information.

It is normal for the front surface of this product to become warm
in use.

DO NOT MEGGER TEST this product as this could result in
damage to the internal electronic components.

76

TECHNICAL SPECIFICATION

1 gang 2 gang

Input Voltage 220-240 Vac 220-240 Vac

Frequency 50/60Hz 50/60 Hz

Output Voltage 5.0Vdc 5.0Vdc

Output Current 2.1A Total 2.1A Total
(shared between both USB
connectors)

Output Power 10.5W 10.5W

Average Active Efficiency 82.7% 83.3%

Efficiency at Low Load (10%)

No Load Power 0.01% 0.02%

Output Connector USB 2.0 Type A

Important Information

This Product falls within the scope of the
Waste Electrical & Electronic Equipment
Directive 2002/96 EC (WEEE).

8 9

77.9% 76.6%

International Customer Care Centre Numbers

Saudi Arabia [phone]

Cyprus [phone]

Iraq [phone]

Jordan [phone]

Lebanon [phone]

Hong Kong [phone]

Nigeria [phone]

UAE/Pakistan/Yemen [phone]

Bahrain [phone]

Kuwait [phone]

Oman 800 73666

Qatar [phone]

UK [phone]

Schneider Electric Ltd,

Stafford Park 5, Telford, Shropshire TF3 3BL, UK

Commercial Registration Number: 02886434

se.com