Schlage VIP 5500 Series,VIP 5594-FSA,VIP 5594-FSE,VIP 5596-FSE,VIP 5596-FSA Installation Manual
Form 57033 Rev. A
01-05-2004
VIP 5500 OPEN ARCHITECTURE MORTISE LOCK
INSTALLATION MANUAL
5500 MORTISE LOCK
AUTOBOLT
5500 MORTISE LOCK
STANDARD
The VIP 5500 series lock is a microprocessor controlled, electromechanical locking system.
It is an open architecture product designed to interface with 3rd party panels encompassing
all the features of the lock, reader, door status and egress (rex/request to exit) indication in
one fire-rated piece of hardware. The 5100 employs a heavy-duty mechanical design tested
and complying with ANSI/BHMA grade 1 standards for performance and reliability. It is powered by 12 or 24 volts DC with only four wires required - two for power and two for communications. The lock communicates with a PIB (panel interface board) which communicates
with the panel as if it were separate components of an access control system.
Operationally, the outside lever is normally locked and the inside lever always retracts the
bolt to allow egress. Electronic access control is achieved by entering an”Access Credential”
(magnetic stripe card or Prox fob or card). The panel controls the lock through the PIB.
Please refer to all instruction manuals involved in the installation before you begin.
Functions
:
VIP 5594-FSA: (1” AutoBolt) - Fail Safe (unlocked)
VIP 5594-FSE: (1” AutoBolt) - Fail Secure (locked)
VIP 5596-FSA: (3/4” latch) - Fail Safe (unlocked)
VIP 5596-FSE: (3/4” latch) - Fail Secure (locked)
Models
:
MG: Magnetic stripe card reader
PX: HID Prox card reader
S
tandard Monitoring Switches:
DSM: Provides door status via data link to panel interface
KSM: Provides mechanical key use events via data link to panel interface
REX: Provides indication of inside lever use for request to exit input via data link
to panel interface
Options
:
T3: Track 3 card reader (data must be ABA track 2 format) - MG only
EXT: exterior use option - MG only (PX model has this standard)
KD: Keyed Different, includes Schlage Everest cylinder
KA: Keyed Alike, includes Schlage Everest cylinder
LC: Less Cylinder
SLB: 2-3/4” backset, 1/2” latch bolt
OLB: 2-3/8” backset, 1/2” latch bolt
ELB: 2-3/4” backset, 3/4” latch bolt
BEFORE YOU BEGIN:
Standard units are shipped from the factory to fit 1-3/4” doors. Verify the door thickness. If the door is not 1-3/4” thick, verify
that the door thickness option was ordered or consult factory.
PRE-INSTALLATION CHECK:
AN OPEN ARCHITECTURE SYSTEM REQUIRES AT LEAST THREE COMPONENTS - A PANEL INTERFACE BOARD (PIB), AN
ACCESS CONTROL PANEL (BY OTHERS) TO WHICH THE PIB IS CONNECTED AND THE VIP LOCK. SEE DOCUMENTATION FOR
THE ACCESS CONTROL PANEL/SOFTWARE THIS LOCK WILL BE USED WITH FOR ANY PRE-INSTALLATION TESTING
REQUIREMENTS AND REMEDIES. REFER TO THE WIRING INFORMATION INCLUDED WITH THE PIB FOR MORE INFORMATION.
PIB
PX MG
Door Thickness
Kits:
Available in 1/8” increments from 1-3/8” to 2-1/2”
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including any interference that may cause undesired operation. Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
Form 57033 Rev. A
01-05-20042
VIP 5500 OPEN ARCHITECTURE MORTISE LOCK
INSTALLATION MANUAL
1. PREP DOOR AND FRAME (IF NOT ALREADY DONE):
A. Determine door hand.
B. Mark the horizontal and vertical centerlines for the lock case (on door edge), strike, lever, and inside escutcheon. Note
that the backset is actually 2.813” (or 2 13/16”). This is very important for proper mounting.
C. Place template on inside of door (opposite the side that the keypad/reader will be on). Line up the correct reference lines
on the template with the edge of the door, depending on the hand (see paper template). The centerline on the door should
line up with the vertical centerline of the template. Use the paper template to mark all holes. (Though the paper template is
the preferred way to prep the door, the dimensions below may be used if a paper template is not available.)
D. Drill required holes. Note that all holes are required except the 3/4” hole just below the 1” hole, this is only required if the
lock has the DSM (door status) switch.
FOR DOOR SWITCH
WIRES:
3/4” HOLE 1” DEEP
DO NOT DRILL THRU
DOOR!
Form 57033 Rev. A
01-05-20043
VIP 5500 OPEN ARCHITECTURE MORTISE LOCK
INSTALLATION MANUAL
Suggested wire raceway:
1/2” hole into top of mortise pocket.
Wiring will exit toward inside
through this hole.
FSE & FSA HARD WIRED MODELS REQUIRE WIRING TO BE RUN
TO THE MORTISE POCKET FROM THE HINGE SIDE. BELOW IS A
SUGGESTED WAY TO DO THIS. A DOOR CORD OR ELECTRIC
HINGE OR TRANSFER DEVICE MUST BE USED TO GET WIRING
FROM THE FRAME TO THE DOOR. NOTE THAT WHEN USING AN
ELECTRIC HINGE IT IS RECOMMENDED THAT THE POWER
WIRES BE DOUBLED OR TRIPLED UP (ON BOTH THE POSITIVE
AND GROUND LEGS) TO AVOID SIGNIFICANT VOLTAGE DROP
THROUGH THE THIN WIRES IN THE HINGE.
Loading...