Schlage SED100 User Manual

SED100 Electronic Touchscreen Deadbolt

USER GUIDE

1

Overview

Key Override

Red indicator

Low Battery Indicator

Green Indicator

Lock Button

Clear Button

Touch Screen

1

1
2
3

6

7

4

5

RED INDICATOR

1

LOCK / UNLOCK

2

Locking, Unlocking and Programming

4

PROGRAMMING

- Touch to activate or lock.

- Unlocks by entering a valid user code.

- Programs by entering a valid programming code.

- Press button to cancel or exit programming mode.

2

LOW BATTERY INDICATOR

Press button to cancel any typo or exit programming mode.

Represents a correct entry or positive response by flashing green light.

Flashes when the batteries are low in power.

Represents an incorrect entry or caution by flashing red light.

5

CLEAR BUTTON

- Locks when pressed.

- Represents “enter” when in programming mode.

6

LOCK BUTTON

Used to unlock with a key when there is a code or battery failure.

7

MECHANICAL KEYWAY OVERRIDE

Protects the batteries.

8

BATTERY COVER

Locks or unlocks manually.

- Press set button for 3 seconds then enter correct programming code to start programming.

- Please refer to for more information about programming mode.

SET BUTTON

2

4

-

9

INTERIOR THUMBTURN

C

C

3

GREEN INDICATOR

4

TOUCH SCREEN

Operation Step 2Step 1

Step 3 Step 4

To unlock

Touch
the
screen.

Enter valid user
code or
programming
code.

Press four random
scramble digits lit on the
screen.

Note:
Only if scramble
code is enabled
(see - - 22).

To lock

To unlock

1 2 3
4 5 6
7 8 9
c

0

→

→

Correct

Incorrect

1 2 3
4 5 6
7 8 9
c

0

→

To lock

→

→

Touch screen is
temporarily disabled
for 60 seconds after 4
consecutive incorrect
attempts.

2

2

NoteFunction

Change the existing programming
code

A programming code can be used to program or
unlock.

Function Code

10

Add a user code(s)

A user code (pin number) is set up by the
programming code and can be used to unlock.

20

Delete all user codes

Deletes all user codes.

40

Add single-entry code(s)

A single-use user code is set up by the program­ming code and can only be used *once* to
unlock.

21

Delete individual user code(s)

Deletes individual user code(s).

30

Keypad scrambling code

The scrambling code is a set of random digits to
be entered prior to any user code or single-entry
code, preventing code probing.

22

Volume control

Incrementally increases volume from mute to
loud.

Set up auto-lock time delay (10-99 seconds).

Locks automatically in 10-99 seconds if enabled.

60

Auto-lock delay timer

70

Auto-lock function

80

Vacation mode

Temporarily disable all active user codes until
unit is re-enabled.

50

3

ACCESS CODE

2

FUNCTION CODES

Code Length Code Capacity Remark

4 - 8 digits 1 set

4 - 8 digits 25 sets

4 digits 4 sets

1. A programming code can be used to program or
unlock.

2. The default programming code is “12345678”.

Programming
Code:

User Code:

Single-entry
Code:

A user code is set up by the programming code
and can be used to unlock.

A single entry code is set up by the programming
code and can only be used *once* to unlock.

21

30

50

70

10

20

22

40

60

80

Function Code

Press [SET] for
3 seconds.

Enter preset
programming code
(12345678) or
current
programming code
if it has been
changed.

0

＋

＋

1

0

＋

＋

2

New
Programming
Code
(4-8 digits)

New
Programming
Code
(4-8 digits)

New User Code
(4-8 digits)

New User Code
(4-8 digits)

Single-use User
Code (4 digits)

Single-use User
Code (4 digits)

0

＋

＋

3

1

＋

＋

2

User Code
(4-8 digits)

Enter new
amount (10-99)

User Code
(4-8 digits)

Delete all user
codes

2

＋

＋

2

0

＋

0

＋

＋

4

C

0

＋

＋

7

0

＋

＋

8

1

＋

Turn On

Turn Off

0

＋

1

＋

Turn On

Turn Off

0

＋

＋

6

0

＋

＋

1

＋

Mute
1 (softer)

2

＋

2 (normal)

3

＋

3 (louder)

0

＋

＋

5

0

＋

1

＋

Turn On

New amount

Turn Off

1 2 3
4 5 6
7 8 9
c

0

Step 1

Step 2 Step 3 Step 4

Change the
existing
programming
code

Add a user
code(s)

Add single-entry
code(s)

Keypad scramble
code

Delete individual
user code(s)

Delete all user
codes

Vacation mode

Volume control

Auto-lock delay
timer

Auto-lock function

The lockset will exit the programming mode and resume to the stand-by status if no input is made in 10 seconds.

Interior Thumbturn

8

Battery Cover

9

Set Button

10

10

3

Troubleshooting

4

Access code list

1

INSTALLATION

SOLUTIONPROBLEM

The latch does not
operate correctly
after installation.

1. Ensure the backset on the latch is set to the proper length.

2. Ensure prior to installation, the latch bolt was retracted and the key was not
inserted into the cylinder when placing torque blade horizontally through latch.

Feel a bump while
turning the
thumbturn or the
key.

1. Execute lock & unlock function to allow the motor to reposition itself again.

2. Redo the Automatic Bolt Direction Step.

2

OPERATION

SOLUTIONPROBLEM

Battery indicator
keeps flashing.

The batteries are low, replace with four new batteries (alkaline batteries only).

Touchscreen is not
responding at all.

1. Check the battery installation.

2. The batteries are low, replace with four new batteries (alkaline batteries
only).

3. Make sure the cable is well-connected to the port, and was not damaged
during installation.

Programming code
cannot be changed.

Please refer to in the installation instructions to restore factory
setting and reprogram all codes.

SOLUTIONPROBLEM

Unble to unlock by
touchscreen.

1. Ensure you have entered the correct user code.

2. The batteries are low, replace with four new batteries (alkaline batteries only).

3. Check the strike plate to make sure it is properly aligned & clear so the bolt
can freely enter the hole.

Restore factory
settings / Lost
programming code.

Please refer to in the installation instructions to restore factory settings.
The orignal default programming code will be restored.

Operating in
darkness.

Touch the screen to activate the back light.

Cannot remove key
unless it is in the
locked position.

If the lock appears to be damaged or does not operate properly, please contact your retailer before
contacting Allegion.

Uninstall the interior and exterior assemblies.
Before re-installation, please follow these guidelines:

1) Ensure the bolt is in the retracted position.

2) Do not have any key inserted in the cylinder.

3) Ensure the torque blade is inserted horizontally.

Programming code

Name User Code

Wrong code was
entered.

Press button once and continue to input code according to regular
procedures.

Cannot delete all
user codes.

1. Ensure the process is completed within 10 seconds, otherwise the unit will
time out.

2. Ensure the programming code has been entered correctly.

C

Cannot add a new
user code.

1. Ensure the process is completed within 10 seconds, otherwise the unit will
time out.

2. Ensure the programming code has been entered correctly.

3. The new user code will not be accepted when the capacity is full. Try to
delete existing user codes and then add new one(s) again.
A user code must be 4 to 8 digits.

"Auto lock" does not
function.

The batteries are low, replace with four new batteries (alkaline batteries only).

The red indicator is
still on after setting
is completed.

1. Check if [SET] button is jammed.

2. Re-install the batteries.

The unit locks when
code is entered and
unlocks when
screen is touched.

Uninstall the interior and exterior assemblies.
Before re-installation, please follow these guidelines:

1) Ensure the bolt is in the retracted position.

2) Do not have any key inserted in the cylinder.

3) Ensure the torque blade is inserted horizontally.

Do not reveal your programming code to anyone.

- C

- 2

Allegion (Australia) Pty Ltd

Phone [phone]
Web www.allegion.com.au

Z10283
N10283

5

Allegion (New Zealand) Limited

Phone [phone]
Web www.allegion.co.nz

- C

- 2

5