Schlage RS485 User Manual

READ FIRST WHEN INSTALLING A PIM-485-16-TD-NXT

Addendum

INSTALLING , CONFIGURING & OPERATING

PANEL INTERFACE

MODULE

RS485

NexSentry Star I/II Version

(PIM-485-16-TD-NXT)

The most current version of this document is available for download at:

http://www.irsupport.net

IR Security & Safety

575 Birch St.

[phone]

[phone] fax

P/N: M053-016-A

575 Birch St.
Forestville, Ct 06010
[phone]
[phone] Fax

World Wide Web

http://www.irsupport.net

Copyright © 2003-2004 Ingersoll-Rand, all rights reserved.

No part of this document can be reproduced, transmitted, or transcribed in any form by electrical, mechanical, optical, manual, or
otherwise without the prior written consent of Ingersoll-Rand. Ingersoll-Rand reserves the right to alter or revise the content of
this document as needed to support future product revisions, without obligation to notify any persons of specific changes.

The use of trademarks, trade names, or other product identification is solely for reference purposes. All other product brand
names are trademarks or registered trademarks of their respective holders.

Ingersoll-Rand believes the information in this document to be accurate and reliable. Ingersoll-Rand does not guarantee results
from the use of this information. Ingersoll-Rand assumes no responsibility, obligation, or liability for the information presented in
this document.

IR Security & Safety

575 Birch St., Forestville, Connecticut 06010 / [phone] / [phone] fax

P/N: M053-016-A http://www.irsupport.net Page 2 of 15

INSTALLATION & OPERATING

INSTRUCTIONS

TABLE OF CONTENTS

1. Wyreless Access™ System (WAS)......................................................................................................................4

1.1 Overview .......................................................................................................................................................4

1.2 Panel Interface Module-RS485-NexSentry (PIM-485-16-TD-NXT) ............................................................5

2. Installing the PIM-485-16-TD-NXT...................................................................................................................8

2.1 Configuring the PIM-485-16-TD-NXT to Emulate DR42xx DigiReaders....................................................8

2.2 Connecting the PIM-485-16-TD-NXT to a Star I/II Access Control Unit...................................................10

2.3 Linking the PIM-485-16-TD-NXT to WAPMs ...........................................................................................11

2.4 PIM-485-16-TD-NXT Card Formats...........................................................................................................12

2.5 PIM-485-16-TD-NXT Alarms.....................................................................................................................12

2.6 What Happens if the PIM-485-16-TD-NXT Loses DC Power....................................................................12

2.7 Using the PIM-485-16-TD-NXT Reset Switch ...........................................................................................12

3. Contacting Schlage............................................................................................................................................13

4. FCC Compliance & Warnings..........................................................................................................................14

4.1 FCC Compliance .........................................................................................................................................14

4.2 Warnings......................................................................................................................................................14

5. Revision History.................................................................................................................................................15

575 Birch St., Forestville, Connecticut 06010 / [phone] / [phone] fax

IR Security & Safety

P/N: M053-016-A http://www.irsupport.net Page 3 of 15

1. Wyreless Access™ System (WAS)

1.1 Overview

Every access control system that uses Wyreless AccessTM contains two different types of modules (Figure
1-1):

• at least one Wyreless Panel Interface Module (WPIM), and

• at least one Wyreless Access Point Module (WAPM)

Figure 1-1 – Wyreless Access System Block Diagram

The WPIM is wired to the access control panel and ideally is installed very close to the access control
panel. The WPIMs installation location is determined by the location of the WAPMs with which it will
communicate using RF.

The WAPM is installed at the access point where access will be controlled and/or monitored. Depending
on the application and which WAPM is used, some wiring at the access control point may be required.

Regardless of which WPIM or WAPM module is used, the communication link between the WPIM and
WAPM is always RF.

This manual describes the installation and operation of a Panel Interface Module-RS485-NexSentry
(PIM-485-16-TD-NXT), a WPIM.

575 Birch St., Forestville, Connecticut 06010 / [phone] / [phone] fax

IR Security & Safety

P/N: M053-016-A http://www.irsupport.net Page 4 of 15

1.2 Panel Interface Module-RS485-NexSentry (PIM-485-16-TD-NXT)

The Panel Interface Module-RS485-NexSentry (PIM-485-16-TD-NXT) is a product in Schlage’s
Wyreless Panel Interface Module (WPIM) category. The PIM-485-16-TD-NXT is the wireless interface
to a NexSentry Star I or Star II Access Control Unit (Figure 1-2).

Figure 1-2 – PIM-485-16-TD-NXT Block Di a gra m

Up to 16 (8 for a Star I) PIM-485-16-TD-NXT can be connected via a 2 wire polled, RS-485 interface to
a Star I/II.

Each PIM-485-16-TD-NXT can emulate up to 16 DR42xx DigiReaders, therefore a PIM-485-xx-NEX
can control from 1 to 16 WAPM’s (1 to 8 for a Star I).

The Schlage Configuration & Demonstration Tool (CDT) is used to determine what RS-485 polling
addresses each PIM-485-16-TD-NXT will emulate.

NOTE: This manual is to be used in addition to the PIM Installation Manual (M053-001-xxx) and
the Wyreless Access System Configuring and Operating Manual (M053-007-xxx).

There are four steps to installing a PIM-485-16-TD-NXT:

1. Using the PIM Installation manual (M053-001-xxx) determine the optimum PIM-485-16-TD-NXT

mounting location and permanently mount the PIM-485-16-TD-NXT in that location.

2. Using the NexSentry Star Access Control Unit User Guide manual (6600062B) for a Star I or the

NexSentry Star II Access Control Unit User Guide manual (6600058A) for a Star II, mount the Star
I/II Access Control Unit and connect it to the PC that will be running either a terminal emulator (Star
I) or the NexSentry software (Star II)

Note: Make certain that that Star I/II Terminal Block TB1 is conf igured for the S-NET
communication protocol.

3. Using this manual configure & connect the PIM-485-16-TD-NXT to the Star I/II Access Control

Unit (section 2.1, page 8).

4. Using this manual, link the PIM-485-16-TD-NXT to all the WAPMs it will control (section 2.3, page

11).

575 Birch St., Forestville, Connecticut 06010 / [phone] / [phone] fax

IR Security & Safety

P/N: M053-016-A http://www.irsupport.net Page 5 of 15