SARGENT WS8900 User Manual

RIGHT HAND

REVERSE BEVEL

“RHRB”

LEFT HAND

REVERSE BEVEL

“LHRB”

OUTSIDE

LEFT HAND REVERSE BEVEL

ILLUSTRATED

FIRST PREPARE DOOR AND MOUNT LOCK

TAPE TEMPLATE TO INSIDE FACE AND EDGE OF DOOR ACCORDING TO DIRECTIONS GIVEN ON TEMPLATE. DRILL HOLES AND MORTISE DOOR FOR LOCK AS INDICATED.

VERTICAL CLOF

CHASSIS

2-3/4"

CYLINDER

OBTAIN DIMENSION TO FINISHED FLOOR FROM TEMPLATE OR FROM RELATIONSHIP TO STRIKE

INSIDE FACE OF DOOR

LATCH BOLT

SECOND ATTACH CHASSIS TO DOOR

A. TEMPORARILY ATTACH CHASSIS TO

RAIL, THEN LOCK PUSH RAIL DOWN USING HEX OR CYLINDER KEY OR HOLDING PUSH RAIL IN DEPRESSED POSITION ON 12-8900 EXIT DEVICE (REFER TO EXPLODED VIEW AT TOP OF PAGE).

NOTE: IF CUTTING OF RAIL WILL BE REQUIRED, IT MAY BE DESIRED TO PROCEED TO STEP 4A PRIOR TO THE TEMPORARY ASSEMBLY OF CHASSIS AND RAIL.

B. POSITION CHASSIS AND RAIL ON DOOR

SO THAT LEVER ARM IS UNDER REAR SECTION OF MORTISE LOCK LEVER. THEN LIFT UP UNTIL LATCH BOLT IS COMPLETELY RETRACTED.

WITH CHASSIS IN THIS POSITION AND RAIL HORIZONTAL, MARK LOCATION OF CHASSIS MOUNTING HOLES. DRILL HOLES FOR SCREWS.

C. RELEASE PUSH RAIL AND DISASSEMBLE

CHASSIS FROM RAIL. THEN MOUNT CHASSIS ON DOOR.

DEPRESS ARM INTO RAIL OPENING AND SLIDE RAIL ONTO CHASSIS

PUSH RAIL

LOCK DOWN SCREW

RAIL ASSEMBLY

ATTACH TO CHASSIS WITH (2) #8-32 X 3/8" PHILLIPS TRUSS HEAD MACHINE SCREWS

LATCH BOLT

LEVER

ARM

LEVER

THIRD APPLY HARDWARE

CHASSIS

ATTACH OUTSIDE TRIM AND CYLINDER, IF USED.

AFTER INSTALLING CYLINDER, TIGHTEN CYLINDER SET SCREW IN LOCK FRONT.

1/8" to 1/4"

THRU CHASSIS

COUNTERSUNK WASHER

THUMB PIECE

FOURTH

APPLY RAIL ASSEMBLY

• CHECK BOX LABEL. IF CUTTING IS NOT REQUIRED, PROCEED TO STEP “B”.

• IF CUTTING IS REQUIRED, CONTINUE WITH STEP “A”.

DETERMINE CUT OFF DIMENSION “X” BY SUBTRACTING 1-3/4" FROM DIMENSION “Y”. MARK CUT OFF POINT ON MOUNTING RAIL.

CUT OFF AND DEBURR

INSERT

X CUTOFF LENGTH

1-3/4" min.

VERTICAL

REFERENCE LINE

(CLCHASSIS)

FOR DOORS WITH STILE, CUT OFF. MUST LEAVE 1/2" MIN. OVERLAP WITH RAIL

LEVEL

RAIL ASSEMBLY

MOUNTING PLATE

ATTACH TO CHASSIS WITH (2) #8-32 X 1/2" PHILLIPS TRUSS HEAD MACHINE SCREWS.

FIFTH APPLY COVERS AND STRIKE

ATTACH END CAP TO

MOUNTING PLATE WITH

(2) COVER SCREWS

ATTA CH

COVER TO

CHASSIS

WITH (4)

COVER

SCREWS

#908

#815

A6705F

CAUTION: BEFORE STARTING

• CHECK HAND OF DOOR (THIS EXIT DEVICE IS HANDED AND NOT REVERSIBLE).

• DOOR SHOULD BE FITTED AND HUNG.

• CHECK BOX LABEL FOR SIZE OF EXIT DEVICE,

FUNCTION AND HAND.

DEPRESS ARM INTO RAIL OPENING AND SLIDE RAIL ONTO CHASSIS. LEVEL RAIL AND FASTEN MOUNTING PLATE.

INSTRUCTIONS FOR INSTALLING WS8900 & 12-WS8900 SERIES MORTISE LOCK TYPE EXIT DEVICE

U.S. PATENT NO. 268003

CANADIAN PATENT RD 1981

FOR ASSISTANCE, CONTACT SARGENT AT 800-727-5477 or www.sargentlock.com

CHASSIS

MOUNTING RAIL

TIGHT AGAINST

RAIL

ATTACH MOUNTING PLATE TO DOOR WITH (3) ROUND HEAD SCREWS

ATTACH STRIKE TO

FRAME (OR DOOR) WITH

(2) STRIKE SCREWS

AVAILABLE STOCK LENGTHS

Length "E": 32" door, no cut off required.

Can be cut to fit doors down to 24" wide.

Length "F": 36" door, no cut off required.

Can be cut to fit doors down to 33" wide.

Length "J": 42" door, no cut off required.

Can be cut to fit doors down to 37" wide.

Length "G": 48" door, no cut off required.

Can be cut to fit doors down to 43" wide.

IMPORTANT: Surface of Door Where Exit Device is to be Applied MUST BE FLUSH. Clear away any Raised Projections to Allow Exit Device

900 Series Mortise Lock

(4) Chassis Shims

to Rest on Flat Surface of Door.

Center Chassis Mounted with (4) #10 Screws Machine

(4) End Bracket Shims

End Bracket

Chassis Cover

RIGHT HAND

REVERSE BEVEL

“RHRB”

LEFT HAND

REVERSE BEVEL

“LHRB”

OUTSIDE

IMPORTANT: SURFACE OF DOOR WHERE EXIT DEVICE IS TO BE APPLIED MUST BE FLUSH. CLEAR AWAY ANY RAISED PROJECTIONS TO ALLOW EXIT DEVICE TO REST ON FLAT SURFACE OF DOOR.

“LOCK DOWN KEY” TO OPERATE: DEPRESS PUSHRAIL. INSERT HEX KEY (OR CYLINDER KEY WHEN USED) AND TURN CLOCKWISE.

(NOT FURNISHED WITH 12-8900 EXIT DEVICE)

New Style Mounting Plate

Standard End Cap (metal)

TOUCH BAR

RAIL ASSEMBLY

ARM

COVER

CHASSIS

LEFT HAND REVERSE BEVEL

ILLUSTRATED

FIRST PREPARE DOOR AND MOUNT LOCK

TAPE TEMPLATE TO INSIDE FACE AND EDGE OF DOOR ACCORDING TO DIRECTIONS GIVEN ON TEMPLATE. DRILL HOLES AND MORTISE DOOR FOR LOCK AS INDICATED.

FASTEN MORTISE LOCK IN PLACE.

VERTICAL CLOF

CHASSIS

2-3/4"

CYLINDER

OBTAIN DIMENSION TO FINISHED FLOOR FROM TEMPLATE OR FROM RELATIONSHIP TO STRIKE

INSIDE FACE OF DOOR

LATCH BOLT

SECOND

ATTACH CHASSIS TO DOOR

A. TEMPORARILY ATTACH CHASSIS TO

RAIL. THEN LOCK PUSH RAIL DOWN USING HEX OR CYLINDER KEY OR HOLDING PUSH RAIL IN DEPRESSED POSITION ON 12-8900 EXIT DEVICE. (REFER TO EXPLODED VIEW AT TOP OF PAGE).

NOTE: IF CUTTING OF RAIL WILL BE REQUIRED, IT MAY BE DESIRED TO PROCEED TO STEP 4A PRIOR TO THE TEMPORARY ASSEMBLY OF CHASSIS AND RAIL.

B. POSITION CHASSIS AND RAIL ON DOOR

SO THAT LEVER ARM IS UNDER REAR SECTION OF MORTISE LOCK LEVER. THEN LIFT UP UNTIL LATCH BOLT IS COMPLETELY RETRACTED.

WITH CHASSIS IN THIS POSITION AND RAIL HORIZONTAL, MARK LOCATION OF CHASSIS MOUNTING HOLES. DRILL HOLES FOR SCREWS.

C. RELEASE PUSH RAIL AND DISASSEMBLE

CHASSIS FROM RAIL. THEN MOUNT CHASSIS ON DOOR.

DEPRESS ARM INTO RAIL OPENING AND SLIDE RAIL ONTO CHASSIS

PUSH RAIL

LOCK DOWN SCREW

RAIL ASSEMBLY

ATTACH TO CHASSIS WITH (2) #8-32 X 3/8" PHILLIPS TRUSS HEAD MACHINE SCREWS

LATCH BOLT

LEVER

ARM

LEVER

THIRD APPLY HARDWARE

CHASSIS

ATTACH OUTSIDE TRIM AND CYLINDER, IF USED.

AFTER INSTALLING CYLINDER, TIGHTEN CYLINDER SET SCREW IN LOCK FRONT.

1/8" to 1/4"

THRU CHASSIS

COUNTERSUNK WASHER

THUMB PIECE

FOURTH APPLY RAIL ASSEMBLY

• CHECK BOX LABEL. IF CUTTING IS NOT REQUIRED PROCEED TO STEP “B”.

• IF CUTTING IS REQUIRED, CONTINUE WITH STEP “A”.

DETERMINE CUT OFF DIMENSION “X” BY SUBTRACTING 1-3/4" FROM DIMENSION “Y”. MARK CUT OFF POINT ON MOUNTING RAIL.

CUT OFF AND DEBURR

INSERT

X CUTOFF LENGTH

1-3/4" min.

VERTICAL

REFERENCE LINE

(CLCHASSIS)

FOR DOORS WITH STILE, CUT OFF. MUST LEAVE 1/2" MIN. OVERLAP WITH RAIL.

LEVEL

RAIL ASSEMBLY

MOUNTING PLATE

ATTACH TO CHASSIS WITH (2) #8-32 X 1/2" PHILLIPS TRUSS HEAD MACHINE SCREWS.

FIFTH APPLY COVERS AND STRIKE

ATTACH END CAP TO

MOUNTING PLATE WITH

(2) COVER SCREWS

ATTACH

COVER TO

CHASSIS

WITH (4)

COVER

SCREWS

#908

#815

A6705F

CAUTION: BEFORE STARTING

• CHECK HAND OF DOOR (THIS EXIT DEVICE IS HANDED AND NOT REVERSIBLE).

• DOOR SHOULD BE FITTED AND HUNG.

• CHECK BOX LABEL FOR SIZE OF EXIT DEVICE,

FUNCTION AND HAND.

AVAILABLE STOCK LENGTHS

Length "E": 32" door, no cut off required.

Can be cut to fit doors down to 24" wide.

Length "F": 36" door, no cut off required.

Can be cut to fit doors down to 33" wide.

Length "J": 42" door, no cut off required.

Can be cut to fit doors down to 37" wide.

Length "G": 48" door, no cut off required.

Can be cut to fit doors down to 43" wide.

DEPRESS ARM INTO RAIL OPENING AND SLIDE RAIL ONTO CHASSIS. LEVEL RAIL AND FASTEN MOUNTING PLATE.

CHASSIS

MOUNTING RAIL

TIGHT AGAINST

RAIL

ATTACH MOUNTING PLATE TO DOOR WITH (3) ROUND HEAD SCREWS

ATTACH STRIKE TO

FRAME (OR DOOR) WITH

(2) STRIKE SCREWS

INSTRUCTIONS FOR INSTALLING 8900 & 12-8900 SERIES MORTISE LOCK TYPE EXIT DEVICE

U.S. PATENT NO. 268003

CANADIAN PATENT RD 1981

FOR ASSISTANCE, CONTACT SARGENT AT 800-727-5477 or www.sargentlock.com