INSTALLATION MANUAL
Color CCD Camera
Install these units securely according to this installation
manual. Be aware that allowing them to fall may cause
personal injury.
This installation should be made by a qualified service
person and should conform to all local codes.
Please read this manual before installing and using this unit, and always follow the instructions in it for proper
use. Please also read the separate Instruction Manual before using the unit for proper use.
Contents
Product Lineup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Surface Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
In-ceiling Mount (Closed Type) . . . . . . . . . . . . . . . . . . 3
In-ceiling Mount (Open Type) . . . . . . . . . . . . . . . . . . . . 4
Connections and Settings . . . . . . . . . . . . . . . . . . . . . . 5
Address Settings Table. . . . . . . . . . . . . . . . . . . . . . . . . 7
Pattern Sheet (inserted at the end of this manual)
Important
• Be careful when opening holes for installing the unit.
Work with the power and video cables pulled out for
easy installation.
• Make sure to properly perform waterproofing for the
ceiling where you are installing the unit.
• Make sure that the surface in the installation location
has no unevenness and is strong enough to bear the
total weight of the unit.
• Install this unit in an environment where the
temperature range stays between -10°C/+14°F and
+50°C/+122°F (no condensation allowed).
English
Before Installing the Unit
Remove the plastic cover (A) and then the
tape (B) fixing the lens.
Put back the plastic cover (A), and turn it
clockwise until you hear it click to securely
lock it.
CAUTION: For VA-80S (Power Borard Unit)
ALL-POLE MAINS SWITCH with a contact separation of
at least 3mm in each pole shall be incorporated in the
electrical installation of the building.
(A)
(B)
Product Lineup
To install the camera unit, the optional housing is required. When using a housing, be sure to choose the correct
one for your environment of use.
Indoor Type Outdoor Type
(In-ceiling Mount)
+
☞P3 ☞P4 ☞P2
(Surface Mount)
In-ceiling
Bracket
Closed Type
VA-80ME
Power Board
Unit
(VA-84S;
for AC24V)
(VA-80S;
for AC230V)
In-ceiling
Bracket
Open Type
VA-80MF
Power Board
Unit
(VA-84S;
for AC24V)
(VA-80S;
for AC230V)
☞ Refer to the instruction
manual supplied with
each product.
Pendant Mounting
Bracket (VA-80BP)
Attachment (VA-80A)
Power Board Unit
(VA-84S; for AC24V)
(VA-80S; for AC230V)
☞ Refer to the instruction manual supplied
with each product.
Wall Mounting
Bracket (VA-80BW)
Outdoor Housing (VA-80EX)
Pole Mounting
Adapter (VA-80AP)
Corner Mounting
Adapter (VA-80AC)
Power Board Unit
(VA-84S; for AC24V)
(VA-80S; for AC230V)
Surface Cover
VA-80F
– 1 –
● Clear Dome Cover (VA-CM8C)
● Smoked Dome Cover (VA-CM8S)
Surface Mount
Make sure to also consult the Surface Cover Instruction Manual.
VA-80F
1. Installing the power board unit
1 Place the pattern sheet at the end of this manual on
the ceiling, mark the locations and drill the holes for
the cables and screws.
● Pull out the cables from the ceiling.
2 Attach the supplied dust sheet (A) to the base of the
power board unit and the detachable piece of the
sheet (B) to the side.
● Peel off the release-coated paper from the dust sheet
before attaching.
3 Pass the cables through the slit (C) in the dust
sheet.
4 Fix the power board unit to the ceiling using the
supplied screws (D) (4 places).
5 Connect the cables and set the switches.
☞ See “Connections and Settings” on page 5.
2. Mounting the camera unit
6 Fasten the camera unit safety wire (F) to the hook
(G) on the inner side of the power board unit.
7 Align the arrows (H) of the same color (blue) on the
camera unit and the power board unit, and push the
camera unit until they click.
8 Align the arrows (H) of the same color (blue) on the
inner side of the surface cover and the power board
unit, and fix the cover by rotating it clockwise.
21
AA
BB
BB
Surface routing (ceiling)
Pass the cables
through the cable hole
(E) at the side of the
power board unit, and
attach the dust sheet
(A) as shown in the
figure.
E
AA
F
3
C
5
4
D
D
G
6
H; Blue 7
■ How to attach the drop-prevention cable
(accessory)
1) Peel off the two-sided tape (K) at the end of the cable
and attach it to the hook (L) on the inner side of the
surface cover as shown in the figure.
2) Fasten the cable to the hook (M) on the side of the
power board unit.
M
K
L
Protrusion
■ To remove the camera unit
H; Blue 8
Removed in case of
surface routing.
Accessories
– 2 –
Dust sheet Drop-prevention
cable
Screw (for power
board unit)
In-ceiling Mount (Closed Type)
1
Make sure to also consult the In-ceiling Bracket Closed Type Instruction Manual.
VA-80ME
1. Installing the power board unit
1 Draw a circumference on the ceiling using the
supplied drop-prevention cable (A) as compass, and
drill a hole for installing the in-ceiling bracket.
● Pull out the cables from the ceiling.
2 Pass the supplied screws a and washer b through
each of the power board unit screw holes (B) and
fasten them loosely using washers (4 places).
3 Align the arrows (C) of the same color (blue) on the
power board unit and the in-ceiling bracket, and
mount the power board unit. Tighten firmly the
screws (B) loosely fastened in the previous step.
● Pass the video cable (D) through the bracket cable
hole as preparation for the next step.
2. Installing on the ceiling
4 Attach the supplied safety wire (E) to the ceiling
beam, for example, then connect it to the
bracket-top hook (F).
5 Connect the video cable and pass the connection
cables through the bracket.
6 Insert the bracket into the ceiling hole and fix it
using screws (G) (2 places).
7 Connect the cables and set the switches.
☞ See “Connections and Settings” on page 5.
8 Align the arrows (C) of the same color (blue) on the
camera unit and the inner side of the bracket, and
push the camera unit until they click.
9 Align the SANYO logos on the supplied bracket
cover and the bracket, and push the cover until they
click.
φ192 mm/7.6”
6
G
A
5
3 C; Blue
4
B
2
B
B
E
F
F
GG
B
a
b
D
E
4
6
7
G
■ How to attach the drop-prevention cable
(accessory)
Fasten the drop-prevention cable (A) to the hooks (H) on
the bracket and its cover, then slide the cable as shown in
the figure.
H
A
H
■ To remove the camera unit
(for power board unit)
Drop-prevention
cable
Accessories
9
C; Blue
8
Bracket coverSafety wireScrew a, washer b
– 3 –
In-ceiling Mount (Open Type)
1
Make sure to also consult the In-ceiling Bracket Open Type Instruction Manual.
1. Installing the power board unit
1 Drill a hole (φ196 mm/7.7”) in the ceiling for
installing the in-ceiling bracket.
● Pull out the cables from the ceiling.
2 Pass the supplied screws a and washer b through
each of the power board unit screw holes (A) and
fasten them loosely using washers (4 places).
3 Align the blue sticker (B) on the bracket and the
arrow (B) of the same color on the power board unit,
and then mount the power board unit in the bracket.
● When inserting the power board unit, do it diagonally.
4 Mount the power board unit in the in-ceiling bracket.
Tighten firmly the screws (A) loosely fastened in the
previous step.
2. Installing on the ceiling
5 Attach the supplied safety wire (C) to the ceiling
beam, for example, then connect it to the
bracket-top hole (D).
6 Pass the connection cables through the slit in the
dust sheet (E), and connect the video cable.
7 Insert the bracket into the ceiling hole and fix it
using screws (F) (2 places).
8 Connect the cables and set the switches.
☞ See “Connections and Settings” on page 5.
9 Align the blue sticker (B) on the bracket and the
arrow (B) of the same color on the camera unit, and
then push the camera unit until they click.
ÀAlign the SANYO logos on the supplied bracket
cover and the bracket, and push the cover until they
click.
7
φ196 mm/7.7”
6
E
3 B; Blue
7
5
VA-80MF
2
a
b
A
A
A
A
C
D
C
5
D
F
8
F
7
F
■ How to attach the drop-prevention cable
(accessory)
Fasten the drop-prevention cable (G) to the hooks (H) on
the bracket and its cover, then slide the cable as shown in
the figure.
H
G
H
■ To remove the camera unit
Dust sheet
Accessories
Screw a, washer b
(for power board unit)
B; Blue 9
Drop-prevention cable
– 4 –
Bracket coverSafety wire
Connections and Settings
Make sure to also consult the Power Board Unit Instruction Manual.
Do not connect the power cord until all other
connections have been completed.
Power Supply Connection
For the connections use cables higher than
LNG
18 AWG.
☞ When using AC 24 V, follow the connection steps in
the leaflet titled “Connecting the power cable” that
comes with the power board unit (VA-84S).
<Live>
<Neutral>
<Ground>
• Fix the power cable end firmly so that the power
terminal connection does not come loose. Use
solderless terminals (ring or spade type) for wiring.
• After connection, always install the supplied power
terminal cover A for safety reasons.
Joint board
AC 230 V
A
BNC type
Monitor Connection
Supported coaxial cables
Cable type Length
RG-59U (3C-2V) 250 m (273.4 yd) max.
RG-6U (5C-2V) 500 m (546.8 yd) max.
RG-11U (7C-2V) 600 m (656.2 yd) max.
• Using different cables from those specified here may attenuate the
video and/or sync signals and interfere with correct transmission.
• RG-59U coaxial cables can be used when distance between
devices is short, but not in duct or aerial routing.
SIDE-A
O
R
B
K
R
D
G
R
B
L
1 Controller connection
WH
L
Y
L
L
S
L
B
R
Connections
White Yellow
485A
485B
2 Alarm signal input
IN 1 - 8
To C OM
✱
Alarm input
signal
3 Alarm signal output
If a lamp is connected to this cable, it will light up
when an alarm signal is received or when the
built-in motion sensor detects movement.
OUT 1/2
✱
To C OM
✱ All connection cables should be 24 AWG or higher with a
maximum length of no more than 600 m (656.2 yd).
☞ For details on 2 and 3, refer to the “Alarm Settings (ALARM)” in
the Instruction Manual.
Alarm output
signal
2
1
SIDE-B
Switch Settings
1 System control setting switches
• Switch 6 is unused.
• The factory setting is represented in bold.
1 Baud rate
Set the same baud rate as that on the camera.
Switch 1 2
2400 OFF OFF
4800 ON OFF
9600 OFF ON
19200 ON ON
2 Control method
Set either to RS485 or coaxial (COAX).
Switch 3
Coaxial (COAX) ON
RS485 OFF
3 Protocol
Set the protocol for controlling the camera.
Switch 4
SSP (SANYO) OFF
PELCO ON
4 Termination (Switch 5)
“OFF” is set by default.
When connecting multiple cameras, termination setting must be “ON”
on the last camera while it must be “OFF” on all others.
ON
123456
1234
CAMERA
LENS
PAN/TILT
AUTO MODE
ALARM
PRIVACY MASK
PASSWORD
LANGUAGE
OPTION
PRESET
MENU
SET
SET
SET
SET
SET
SET
SET
SET
SET
OFF
BACK
ALARM
ALARM IN
y
ALARM OUT
ALARM DISABLE
MOTION
ALARM DISPLAY
PRESET
MENU
1
1
OFF
OFF
OFF
OFF
BACK
y
2 Address setting switches
Set the camera address.
See “Address Settings Table” on page 7.
ON
12345678
– 5 –
Connections and Settings
■ To prevent electromagnetic interference
Be sure to attach the clamping cores supplied with the camera unit to the cables as illustrated.
Power cable
Control and alarm input/output cables
Video cable
■ Connections for using coaxial control (System connection)
(1 - 16)
MONITOR OUT
MAIN
Video input
MON2
terminal
CameraCamera
A RS-485 B
DO NOT CONNECT TO PHONE LINE
Terminator
switch
Communication conversion
connectors
Monitor
(sold separately)
Video input
terminal
Digital video recorder (sold separately)
1
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
IN
OUT
Video input
terminal
System controller
(sold separately)
– 6 –
TELEMETRY
VIDEOAB
Address Settings Table
Addresses are specified by setting the switches to ON/OFF.
In the table, the circle mark “m” means ON. Set switches as shown in the table.
SANYO protocol: 1 - 127 PELCO protocol: 1 - 255
ON
ONOFF
ON
ONOFF
Switch 8
• Address 1 - 127: OFF
12345678
• Switch 8 is unused.
Address
(Camera No.)
Protocol
SANYO/PELCO
0* 128
1 129
2 130
3 131
4 132
5 133
6 134
7 135
8 136
9 137
10 138
11 139
12 140
13 141
14 142
15 143
16 144
17 145
18 146
19 147
20 148
21 149
22 150
23 151
24 152
25 153
26 154
27 155
28 156
29 157
30 158
31 159
32 160
33 161
34 162
35 163
36 164
37 165
38 166
39 167
40 168
41 169
42 170
PELCO 1 2 3 4 5 6 7
Switch No.
m
m
m m
m
m m
mm
m m m
m
m m
mm
m m m
mm
m m m
mmm
m m m m
m
m m
mm
m m m
mm
m m m
mm m
m m m m
mm
m m m
mmm
m m m m
mmm
m m m m
mmmm
m m m m m
m
m m
mm
m m m
mm
m m m
mm m
m m m m
mm
m m m
mmm
* When setting the address by using the menu screen on the camera, set the address setting switches to “0”.
12345678
Address
(Camera No.)
Protocol
SANYO/PELCO
43 171
44 172
45 173
46 174
47 175
48 176
49 177
50 178
51 179
52 180
53 181
54 182
55 183
56 184
57 185
58 186
59 187
60 188
61 189
62 190
63 191
64 192
65 193
66 194
67 195
68 196
69 197
70 198
71 199
72 200
73 201
74 202
75 203
76 204
77 205
78 206
79 207
80 208
81 209
82 210
83 211
84 212
85 213
PELCO 1 2 3 4 5 6 7
• Address 128 - 255: ON
Switch No.
m m m m
mm m
m m m m
mmm m
m m m m m
mm
m m m
mmm
m m m m
mmm
m m m m
mm mm
m m m m m
mmm
m m m m
mmmm
m m m m m
mmmm
m m m m m
mmmmm
m m m m m m
m
m m
mm
m m m
mm
m m m
mm m
m m m m
mm
m m m
mm m
m m m m
mm m
m m m m
mmm m
m m m m m
mm
m m m
mmm
m m m m
mmm
m m m m
Address
(Camera No.)
Protocol
SANYO/PELCO
86 214
87 215
88 216
89 217
90 218
91 219
92 220
93 221
94 222
95 223
96 224
97 225
98 226
99 227
100 228
101 229
102 230
103 231
104 232
105 233
106 234
107 235
108 236
109 237
110 238
111 239
112 240
113 241
114 242
115 243
116 244
117 245
118 246
119 247
120 248
121 249
122 250
123 251
124 252
125 253
126 254
127 255
PELCO 1 2 3 4 5 6 7
Switch No.
mmmm
m m m m m
mm m
m m m m
mmmm
m m m m m
mmm m
m m m m m
mmmm m
m m m m m m
mm
m m m
mmm
m m m m
mmm
m m m m
mm mm
m m m m m
mmm
m m m m
mmmm
m m m m m
mm mm
m m m m m
mmm mm
m m m m m m
mmm
m m m m
mmmm
m m m m m
mmmm
m m m m m
mm mmm
m m m m m m
mmmm
m m m m m
mmmmm
m m m m m m
mmmmm
m m m m m m
mmmmmm
m m m m m m m
– 7 –
Pattern Sheet
4- φ4.5 (0.2)
P. D φ168 (6.6)
166 (6.5)
186 (7.3)
Scale: 1/1
Unit: mm (inch)
MEMO
...............................................................................................
...............................................................................................
...............................................................................................
...............................................................................................
...............................................................................................
...............................................................................................
...............................................................................................
...............................................................................................
...............................................................................................
...............................................................................................
...............................................................................................
...............................................................................................
...............................................................................................
...............................................................................................
...............................................................................................
b Dimensions
71 (2.8)
156 (6.1)
φ136 (5.4)
Unit: mm (inch)
Printed on recycled paper
Imprimé sur du papier recyclé
Impreso en papel reciclado
Gedruckt auf Recyclingpapier
使用再生纸印刷
1AC6P1P3149-A
L5BU2/XE (0807KP-HS)
SANYO Electric Co., Ltd.
Printed in China
Loading...