Sanyo VCB-3442P Instruction Manual

Download

Page 1

INSTRUCTION MANUAL

index

BEDIENUNGSANLEITUNG MANUEL D’INSTRUCTIONS

B/W CCD Camera CCD-Schwarzweißkamera Caméra CCD Noir et Blanc

CCD

VCB-3442P

About this manual

Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.

Über diese Bedienungsanleitung

Lesen Sie bitte vor der Montage und dem Inbetriebnehmen der Kamera zuerst diese Bedienungsanleitung sorgfältig durch und bewahren Sie sie zum späteren Nachschlagen auf.

A propos de ce manuel

Avant d’installer et d’utiliser la caméra, veuillez lire ce manuel attentivement. Gardez-le à portée de main pour toute référence ultérieure.

Page 2

Depending on the conditions of use, installation and environment, please be sure to make the appropriate settings and adjustments. If you need help with installation and/or settings, please consult your dealer.

CONTENTS

PRECAUTIONS..................................................................................... 2

PARTS NAMES..................................................................................... 3

MOUNTING THE LENS........................................................................ 6

CONNECTIONS.................................................................................... 8

SETTINGS............................................................................................. 9

TROUBLESHOOTING........................................................................... 12

SPECIFICATIONS.................................................................................. 13

ACCESSORIES...................................................................................... 14

FEATURES

• Built-in interline transfer method 1/3" CCD, approx. 320,000

picture elements

• Low smear, anti-blooming, low lag, no burning and no geometric

distortion using the CCD solid state image device.

• 100% solid state components giving excellent immunity to shock

and vibration

• Not subject to interference from magnetic or electrostatic fields

• High sensitivity, minimum required illumination of 0.05 lux with

F1.2 lens

• Horizontal resolution, more than 400 TV lines

• Backlight compensation function (Active when using an auto-iris

lens)

• Externally adjustable flange back (mechanical focus)

• Low power consumption and quick start

• 12 V DC operation

English 1

Page 3

PRECAUTIONS

In case of problem

Do not use the camera if smoke or a strange odour comes from the unit, or if it seems not to function correctly. Disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Centre).

Do not open or modify

Do not open the cabinet, as it may be dangerous and cause damage to the unit. For internal settings and repairs, consult your dealer (or a Sanyo Authorized Service Centre).

Do not put objects inside the unit

Make sure that no metal objects or flammable substance get inside the camera. If used with a foreign object inside, it could cause a fire, short-circuits or damages.

If water or a liquid gets inside the camera, disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Centre). Be careful to protect the camera from rain, sea water, etc.

Be careful when handling the unit

To prevent damages, do not drop the camera or subject it to strong shock or vibration.

Install away from electric or magnetic fields

If installed close to a TV, radio transmitter, magnet, electric motor, transformer, audio speakers the magnetic field they generate will distort the image.

Protect from humidity and dust

To prevent damages to the camera, do not install it where there is greasy smoke or steam, where the dampness may get too high, or where there is a lot of dust.

Protect from high temperatures

Do not install close to stoves, or other heat generating devices, such as spotlights, etc., or where it could be subject to direct sunlight, as that could cause deformation, discoloration or other damages.

Be careful when installing close to the ceiling, in a kitchen or boiler room, as the temperature may raise to high levels.

Install where the temperature range will stay between –10˚C and 50˚C. (no condensation)

Cleaning

• Dirt can be removed from the cabinet by wiping it with a soft

cloth. To remove stains, wipe with a soft cloth moistened with a soft detergent solution and wrung dry, then wipe dry with dry soft cloth.

• Do not use benzine, thinner or other chemical product on the

cabinet, as that may cause deformation and paint peeling. Before using a chemical cloth, make sure to read all accompanying instructions. Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time, as that may cause damage or paint peeling.

2 English

ENGLISH

Page 4

PARTS NAMES

BLC AGC

POWER

English 3

OFF OFF

DC12V GND

1 Camera setup section

• Electronic iris (EI)/Auto iris (AI) setting

• Backlight compensation (BLC) setting

VIDEO OUTSHUTTER

• Automatic gain control (AGC) setting

2 Power indicator (POWER)

Comes on when the power to the camera is on.

3 12 V DC input terminal (12 V DC, GND)

4 High speed electronic shutter switch (SHUTTER)

5 Video output connector (VIDEO OUT: BNC type)

Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector.

6 Lens iris level volume (LEVEL)

7 Auto-iris lens switch (DC/VIDEO)

8 Lens iris output connector (LENS)

Page 5

PARTS NAMES

9 Flange-back lock screw

F Lens mount cap

The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately).

G Camera installation bracket

The bracket can be fixed at the top or bottom of the camera.

A Camera mounting screw hole: 1/4"-20 UNC

CAUTION:

When installing the camera support, select a location that can support the total weight of the camera and accessories.

4 English

Page 6

PARTS NAMES

LEVEL

VIDEO

LENS

Concerning auto-iris lenses

DC type auto-iris lens

A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is referred to as DC type coil lens or DC type non-amplifier lens.

(Set the Auto-iris lens switch to the DC position.)

VIDEO type auto-iris lens

A lens with amplifier circuit that operates on video signal and DC power source. In general, this type of lens is referred to as EE amplifier type lens.

ALC and LEVEL volume level controls are available on the lens for iris adjustments. (Set the Auto-iris lens switch to the VIDEO position.)

Compatible auto-iris lenses

1/3 inch Sanyo DC type lens VIDEO type lens

VCL-CS8LY: Standard angle, f= 8 mm Standard angle, f= 9 mm VCL-CS4LY: Wide angle, f= 4 mm Telephoto angle, f= 12 mm VCL-CS2LY: Ultra-wide angle, f= 2.8 mm More telephoto angle, f= 16 mm

If using a VIDEO type auto-iris lens

• Set the ALC and LEVEL controls on the lens to adjust the iris. Normally the ALC volume should be turned

all the way to Av (Average).

• Depending on the type of lens used, the lens may not perform properly. In such a case, adjust the LEVEL

volume on the lens casing to correct.

English 5

Page 7

MOUNTING THE LENS

Please use a DC type auto-iris lens (sold separately).

Checking the lens mount

Do not use a lens if length “L” is more than 9 mm. If not, that may damage the camera and prevent proper installation.

1 Remove the lens mount cap from the camera. 2 Install the auto-iris lens.

CS mount type lens

Carefully align the lens mount with the camera opening, then turn the lens slowly to install it.

C mount type lens

To allow for flange-back adjustment, install the C-mount adaptor (option) on the lens mount, then carefully align the lens mount with the camera opening and turn the lens slowly to install it.

3 Connect the lens plug to the lens iris output connector (LENS) on the side of the camera.

When using lenses from other makers, the plug shape may not correspond to the terminal on the camera. In such a case, remove the original plug and using a soldering iron, connect the supplied lens iris plug according to the diagram. (Refer to page 7.)

C mount type lens

CS mount type lens

6 English

Page 8

MOUNTING THE LENS

Rewiring the lens cable in the lens iris plug

1 Prepare the lens cable.

Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire.

2 Install the lens iris plug.

Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close the plug cover.

Pin layout

DC type lenses VIDEO type lenses

Brake coil (–) +10 V DC (50 mA max.)

Brake coil (+) Not used

Drive coil (+) Video output (1.0 Vp-p, high impedance)

Drive coil (–) Ground (for video signal and DC power)

1 3

English 7

Flange-back adjustment

If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the flange-back position as described below.

1 Before installing the lens, check that the two flange-back lock screws have been tightened.

If the flange-back lock screws are loose, the CS mount ring will not be secured and it will not be possible to

adjust the flange-back.

2 Fully install the lens, then loosen the two flange-back lock screws. 3 Set the zoom lens to the maximum telephoto position (TELE), then set the focus using the focus ring on the lens.

1, 3

4 Set the zoom lens to the maximum wide angle position (WIDE), then set the focus by turning the CS mount ring. 5 Repeat steps 3 and 4 until the image stays in focus when changing from a telephoto shot to a wide angle shot.

When the setting is complete, tighten the two flange-back lock screws.

Page 9

CONNECTIONS

(A)

(Video signal connections)

: VIDEO IN : VIDEO OUT

Basic connection for monitoring or recording

The peripheral devices (VCR, monitor, lens, etc.) and cables are sold separately.

1 Make the video signal connection between the camera and the monitor or time lapse VCR. 2 Connect DC connecting cord from the AC adaptor to the 12 V DC IN terminal on the camera.

WARNING:

• This AC adaptor is specially conceived for this camera. Never use another type of AC adaptor with this

camera, and do not use this AC adaptor to power other types of cameras.

• Not for use with toys.

• Never try to disassemble or modify the AC adaptor.

3 Insert the plug of this power cord into a wall outlet.

The POWER indicator (A) will light. Adjust the picture on the monitor using the Brightness and Contrast controls.

Coaxial cable type and maximum length

• Cable type RG-59U (3C-2V), 250 m maximum.

• Cable type RG-6U (5C-2V), 500 m maximum.

• Cable type RG-11U (7C-2V), 600 m maximum.

CAUTION:

• The RG-59U type cable should not be run through electrical conduits or through the air.

• Using CCTV/Video-grade coaxial cable.

8 English

Page 10

SETTINGS

Camera setup section

EI BLC AGC

• Electronic iris (EI)/Auto iris (AI) setting

• Backlight compensation (BLC) setting

• Automatic gain control (AGC) setting

English 9

AI OFF

OFF

Electronic iris function setting

Use a manual or fixed iris lens and set the lens aperture to the shortest F stop. Set the EI/AI switch to EI position.

☞ When using an auto-iris lens (for indoor/outdoor use)

Set the EI/AI switch to the AI position.

Note:

• The electronic iris is suitable for normal indoor use. When the

EI/AI switch is set to the EI position, do not use an auto-iris lens.

• If used under fluorescent light, the image may flicker. In such a

case, change to incandescent lighting or set the EI/AI switch to the AI position and use an auto-iris lens.

• When shooting bright subjects, pay attention to the light angle in

order to avoid or minimize the smear phenomenon effect.

• If conditions are outside the electronic iris operation range or more

than the maximum illumination, it will cause saturation of the CCD. In that case, use a manual iris lens.

Page 11

SETTINGS

Lens iris adjustment

If using a DC type auto-iris lens, you will need to set the LEVEL volume when shooting in the conditions described below.

L (counterclockwise): To decrease the contrast H (clockwise): To increase the contrast

• If shooting simultaneously in a dark room

and through a bright window.

• If the subject background is extremely

bright or dark.

• If the brightness of the picture on the

monitor is not correct.

LEVEL

Backlight compensation setting

Use an auto-iris lens and set the BLC switch to the ON position, to engage the backlight compensation function.

If using a VIDEO type auto-iris lens

• The ALC volume on the lens should be turned all the way to Av

(Average).

• If the backlight compensation function does not compensate

properly for the conditions, set using the LEVEL volume on the lens.

OFFBLC

AGC setting

AGC (Automatic gain control) can be turned ON or OFF. AGC (ON): Auto gain control OFF: Fixed gain

OFFAGC

10 English

Page 12

SETTINGS

High speed electronic shutter setting

Normally, the speed setting switch for the high speed electronic shutter set to the 0 position. This sets the electronic shutter speed to 1/50 sec. The switch can be set as indicated in table A to select one of the 8 speeds available.

CAUTION:

• When using the high speed electronic shutter, the EI/AI switch

must be set to the AI position.

• Using the high speed electronic shutter indoors with low lighting,

will give darker pictures. In such a case, add some lights to make sure the lighting is sufficient. If the lighting is very bright, pay attention to the light angle in order to avoid or minimize the smear phenomenon effect.

Table A

0123456 7

1/50 1/120 1/250 1/500 1/1000 1/2000 1/4000 1/10000

(Unit: sec.)

English 11

Page 13

TROUBLESHOOTING

Before taking the camera for repairs, please check below to make sure that the camera is used correctly. If it still does not perform correctly, please consult your dealer or a Sanyo Authorized Service Centre.

No picture on the monitor screen

• Is the power turned on to all connected devices? Is the voltage correct?

• Are all the signal connecting cables correctly connected?

• Is the lighting sufficient?

• Has the lens cap been removed?

• Is the lens type (DC or VIDEO) correctly selected?

Depending on the type of lens, the A. I. LENS switch must be set accordingly.

• Is the iris control correctly set?

A: When using a DC type lens, the LEVEL volume should be adjusted. B: When using a VIDEO type lens, the LEVEL volume (on the lens) should be adjusted.

The picture is not clear

• Is the monitor correctly adjusted?

• Is the flange-back position correctly set?

• Is the lens focus correctly adjusted?

• Are the lens surfaces clean?

If there is dust or finger prints on the lens, the image quality will deteriorate. To clean the lens use a soft cloth or a commercially available lens cleaning set.

12 English

Page 14

SPECIFICATIONS

Scanning system : CCIR standard (625 TV lines,

Interlace : 2:1 interlace Image device : 1/3 inch solid state image device CCD Picture elements : 542 (H) x 584 (V) Effective picture elements : 512 (H) x 582 (V) Synchronizing system : Internal sync Resolution : 400 TV lines horizontally, 400 TV lines

Video output level : 1.0 Vp-p/75 ohms, composite Video S/N ratio : More than 50 dB Minimum required

illumination (incandescent lighting)

Backlight compensation : Manual ON/OFF switching, zone light

Electronic iris function : Manual ON/OFF switching High speed electronic

shutter

Electronic iris range : 0.07 lux to 42,000 (F 1.4, lens) Flange-back : 12.5 mm ± 0.8 mm

Gamma correction : γ = 0.45 Lens mount : CS mount Environmental conditions : Temperature: –10˚C ~ +50˚C

Power supply : 12 V DC

25 frames/sec.)

vertically

: Approx. 0.05 lux with a F 1.2 lens,

approx. 0.07 lux with a F 1.4 lens

measuring system (Active when using an auto-iris lens)

: 8 speeds, selectable by switch:

(1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 sec.)

0.05 lux to 30,000 (F 1.2, lens)

Humidity: less than 90% (no condensation)

English 13

Power consumption : 12 V DC/190 mA (with auto iris lens)

12 V DC/140 mA (without auto iris lens)

Weight : Approx. 370 g (without lens)

AC Adaptor:

Environmental conditions : Temperature: –10˚C ~ +50˚C

Humidity: less than 90% (no condensation)

Power requirement : 220 – 230 V AC 50Hz Power consumption : 4.3 W (with auto iris lens)

3.7 W (without auto iris lens)

Weight : Approx. 480 g

SERVICE

This camera is a precision instruments and if treated with care, will provide years of satisfactory performance. However, in the event of a problem, the owner is advised not to attempt to make repairs or open the cabinet. Servicing should always be referred to your dealer or Sanyo Authorized Service Centre.

Page 15

SPECIFICATIONS

ACCESSORIES

Dimensions

OFF

BLC

OFF

AGC

POWER

DC12V GND

58.5

VIDEO OUTSHUTTER

48.9

135

123

1,830

1/4”–20 UNC

81.4

1,830

Features and specifications are subject to change without prior notice or obligations.

1 Lens iris plug (4-pin)..................................................................1 pc.

2 AC adaptor ...............................................................................1 pc.

3 Hexagonal wrench....................................................................1 pc.

123

14 English