(1) General-----------------------------------------------------------------------------1
(2) Frame Chart-------------------------------------------------------------------fig.1
(3) IC Function Introduction ------------------------------------------------------1
(5) IC Voltage --------------------------------------------------------------8
(6) Trouble shorting------------------------------------------------------------------9
This chassis is consists of main IC TMPA8859, TA1343N, TC90L01N. TMPA8859 is an
integrated circuit for a PAL/NTSC TV. A MCU and a TV signal processor (SP) are integraed in a 64-pin
shrink DIP package. The MCU contains 8-bit CPU,ROM,RAM,I/O ports,timer/counters, A/D
converters,an on-screen display controller,remoter control interfaces,IIC bus interfaces. The TV signal
processor contains PIF,SIF,Video,multi-standard chroma,Sync,RGB processors.
(2) Frame Chart (see fig.1)
L
→
TUNER
AV/TV SWITCH
TC90L01
AUDIO PRO.
TA1343N
AUDIO POWER
TN8246H
R
PIF/SIF R, G, B
TMPA 8859
VT/BL BH/RF AGC
CRT
OSCILLLLATION
2SC3619 X 3
VM
V-OUT
TDA8172
DPC CIRCUIT
2SD880
H-OUT
2SD2539
SCAN
TRANSFORMER
B
-
2-12R
+130V +22V +27V
110- 220V +13
ON/OFF POWER
STR-G9656
fig.1
1
(3) IC Function Introduction
3.1 N501 TMPA8859 Function: MCU and SP
Icon PIN Description
SDA2 1 IIC bus serial data input/output
X-RAY 2 X-ray Output
KEY 3 Key input
DVSS 4 GND connection
RESET 5 Reset signal input
XOUT 6 8 MHz oscillator connection
XIN 7 8 MHz oscillator connection
TEST 8 GND connection
DVDD 9 5V power supply
VVSS 10 GND connection
TV GND 11 GND terminal for Analog block
FBP IN 12 Input terminal for FBP
H.OUT 13 Horizontal driving pulse output
H.AFC1 14 H AFC filter connection
V.SAW 15 Terminal to be connected capacitor to generate V saw signal
V.OUT 16 Vertical driving pulse output
H.Vcc(9V) 17 Vcc terminal for DEF circuit
Ys 18 Ys IN
Cb in 19 Input terminal for Cb signal
Y in 20 Input terminal for Y signal
Cr in 21 Input terminal for Cr signal
DIG GND 22 GND terminal for Digital block
C in 23 Input terminal for Chroma signal
V2 in 24 Input terminal for Video signal
DIG Vdd 25 Vcc terminal for Digital block
CW out 26 Output terminal for fsc wave signal
ABCL in 27 Input terminal for ABL/ACL control
EW out 28 Output terminal for east-west correction singal
IF Vvv(9V) 29 Vcc terminal for IF circuit
TV out 30 Detected PIF signal output terminal
SIF out 31 Detected SIF signal output terminal
EHT in 32
H.C0TT in 33
DC NF 34 Terminal to be connected capacitor for DC Negative feedback
PIF PLL 35 Loop filter for PIF PLL connection
IF Vvv(5V) 36 Vcc terminal for IF circuit
REG FIL 37 Terminal to be connected capacitor for stabilizing internal bias
DE-EMP 38 Terminal to be connected capacitor for SIF Det De-Emphasis
IF AGC 39 IF AGC filter connection
2
IF GND 40 GND terminal for IF circuit
IF IN 41 Input terminals for IF signals
IF IN 42 Input terminals for IF signals
RF AGC 43 RF AGC control level output
YC Vcc 44 Vcc terminal for Y/C circuit
Vsm out 45 Output terminal for Vsm signal
Black DET 46 Terminal to be connected with Black Det filter for black stretch
APC Filter 47 Terminal to be connected with APC filter for Chroma demodulation
IK IN 48 Sense ACB cathode current input
RGB Vcc 49 Vcc terminal for RGB circuit
R OUT 50 Output terminal for R signal
G OUT 51 Output terminal for G signal
B OUT 52 Output terminal for B signal
TV GND 53 GND terminal for Analog block
A GND 54 GND connection
A VDD 55 5V power supply
MUTE 56
SDA1 57 IIC bus serial data input/output
SCL1 58 IIC bus serial clock input
PWM 59
LED 60
SCL2 61 IIC bus serial clock input
SYNC 62 Horizontal sync signal input
REMOTE 63 Remote controller signal input
POWER 64 Power control (On=Hi. Off=L)
3.2 N001 TC90L01N Function: I
Name Pin Function
Lin TV 1 This pin is for input a left audio signal form the main demodulator in the TV
Vin TV 2 This pin is for input a composite video signal form the main demodulator in the TV
Rin TV 3 This pin is for input a right audio signal form the main demodulator in the TV
V/Yin V1 4 This pin is for input a luminance signal or composite video signal from an external
source(V1 channel)
LinV1 5 This pin is for input a left audio signal from an external source(V1 channel)
CinS1 6 This pin is for input a chroma signal from an external source(S1 channel)
RinV1 7 This pin is for input a right audio signal from an external source(V1 channel)
VinV2 8 This pin is for input a composite video signal from an external source(V2 channel)
LinV2 9 This pin is for input a left audio signal from an external source(V2 channel)
ALC 10 This is an detect output pin of ALC(Auto Level Control)
RinV2 11 This pin is for input a right audio signal from an external source(V2 channel)
Vcc 12 This is the power supply pin. Apply 9V to this pin.
SDA 13 This is an IIC bus data input/output pin.
SCL 14 This is an IIC bus clock input pin.
GND 15 This is the GND pin.
Rout TV 16 This pin is for output right audio signal.
2
C bus control , Audio/Video switching IC
3
Lout TV 17 This pin is for output left audio signal.
Yout 18 This pin is for output luminance signal.
BAND2 19 This pin is for output band2 to control tuner.
Cout 20 This pin is for output chroma signal.
BAND1 21 This pin is for output band1 to control tuner.
Vout 22 This pin is for output main channel composite video signal.
Rout Mon 23 This pin is for monitor-output right audio signal.
Lout Mon 24 This pin is for monitor-output left audio signal.
3.3 N301 TDA8172 Function: V-scan output
PIN FUNCTION
Offset canceling filter 1 DC offset canceling filter for bass boost.
1 2-5 Terminals for capacitors of the phase shift blocks.
φ4-φ
Lch input 6 Audio input terminal.
GND 7 GND terminal.
Rch input 8 Audio input terminal.
Bias filter 9 Filter for noise rejection of the bias.
Bass LPF(R) 10 LPF for bass control circuits.
Treble HPF(R) 11 HPF for treble control circuits.
Wch output 12 Woofer audio output terminal.
Rch output 13 Right audio output terminal.
Treble HPF(L) 14 HPF for treble control circuits.
Bass LPF(L) 15 LPF for bass control circuits.
Lch output 16 Left audio output terminal.
Woofer LPF1 17 LPF for bass boost cir cu it.
Woofer LPF2 18 LPF for bass boost cir cu it.
Woofer LPF3 19 LPF for bass boost cir cu it.
Vcc 20 This is the power supply pin. Apply 9V to this pin.
Volume filter 21 Smoothing filter for volume control
Woofer LPF 22 Smoothing filter for bass boost control
SCL 23 This is an IIC bus clock input pin.
SDA 24 This is an IIC bus data input/output pin.
4
3.5 N602 TA8246 Function: Audio power amplifier
Name Pin Function
NC 1
IN2 2 Audio signal input2.
Pre-GND 3 GND terminal.
IN1 4 Audio signal input1.
MUTE.SW 5 Mute control terminal.
RF 6 Ripple filter terminal.
MUTE. T.C. 7 Mute control terminal.
OUT1 8 Audio signal output1.
Vcc 9 This is the power supply pin
PW-GND 10 GND terminal.
NC 11
OUT2 12 Audio signal output2.
(4) I2C Bus Control
4.1 Menu Entry
Press “D” button on the factory remote control to enter the “D” mode, the letter “D” will be
displayed at the upper right coner and the adjusting items will be displayed at the upper left conrer.
Press the channel +/- to select the preferred item; press the volume +/- to adjust the value of each item.
4.2 Item introduction
TMPA8859 BUS DATA
No S D item Comment
1 S D1 RCUT R CUTOFF 20
2 S D1 GCUT G CUTOFF 20
3 S D1 BCUT B CUTOFF 20
4 S D1 GDRV G DRIVE 40
5 S D1 BDRV B DRIVE 40
6 D1 CNTX SUB CONTRAST MAX
7 S D1 BRTC SUB BRIGHT CEN
8 S D1 COLC NTSC SUB COLOR CEN
9 S D1 TNTC SUB TINT CEN
10 S D1 COLP PAL SUB COLOR CEN(difference)
11 D1 COLS SECAM SUB COLOR CEN
12 S D1 SCOL SUB COLOR CENTER for DVD
13 D1 SCNT SUB CONTRAST
14 D1 CNTC SUB CONTRAST CEN
15 D1 CNTN SUB CONTRAST MIN
16 D1 BRTX SUB BRIGHT MAX
17 D1 BRTN SUB BRIGHT MIN
18 D1 COLX SUB COLOR MAX
7F
50
40
40
00
40
07
0D
30
02
20
30
3F
5
19 D1 COLN SUB COLOR MIN
20 D1 TNTX SUB TINT MAX
21 D1 TNTN SUB TINT MIN
22 D1 ST3 NTSC SHARP CEN (TV)
23 D1 SV3 NTSC SHARP CEN (AV)
24 D1 ST4 OTHER SHARP CEN (TV)
25 D1 SV4 OTHER SHARP CEN (AV)
26 D1 SVD SHARP CENTER in DVD
27 D1 ASSH ASYMMETRY-SHARPNESS
28 D1 SHPX SUB SHARP MAX(difference)
29 D1 SHPN SUB SHARP MIN(difference)
30 D1 TXCX UV COLOR MAX
31 D1 RGCN UV COLOR MIN
32 D1 ABL ABL data
33 D1 DCBS A part of video data
34 D1 CLTM The data when TV mode
35 D1 CLVO The data when AV mode
36 D1 CLVD The data when DVD mode
37 D1 DEF
38 D1 AKB
39 D1 R SNS R SENSE
40 D1 G SNS G SENSE
41 D1 B SNS B SENSE
100 D1 BASC BASS Center
101 D1 BASX BASS MAX
102 D1 TREC TREBLE Center
103 D1 BALC BALANCE Center
104 D1 WOFC WOOFER Center
105 D1 BAS1 BASS data in MEMORY 1
106 D1 BAS2 BASS data in MEMORY 2
107 D1 BAS3 BASS data in MEMORY 3
108 D1 TRE1 TREBLE data in MEMORY 1
109 D1 TRE2 TREBLE data in MEMORY 2
110 D1 TRE3 TREBLE data in MEMORY 3
111 D1 WFL1 Woofer data in MEMORY 1
112 D1 WFL2 Woofer data in MEMORY 2
113 D1 WFL3 Woofer data in MEMORY 3
114 D1 WON1 WOOFER ON coefficient
115 D1 WON2 WOOFER ON coefficient
116 D1 WOFF WOFFER out level when Woofer off
117 D1
118 D1
119 D1
120 D1
121 D1
122 D1
123 D1
124 D1
125 D1
126 D1
127 D1
128 D1
AUCON1
AUCON2
AUALI1
AUALI2
AUTIM
AUSTP Audio step
VPCT X-ray protection counter
TUNR Select tuner
CCDOSD
CCDOSDF
OSDF
OSD
Stereo/SAP noise threshold
Level adjust setting
For wideband expander
For spectral expander
Timing current alignment data
129 D1 PDOPT0 PANDA OPTION0
130 D1 PDOPT1 PANDA OPTION1
131 D1 Waittime V-MUTE when POWER ON
132 D1 CUR CEN CENTER OF SCREEN OPEN
133 D1 CUR STEP STEP OF SCREEN OPEN
134 D1
135 D1
136 D1
General, these failures are produced by power sources, because of which refer to a wider area, so that can
be divided them two conditions to explain: no B1 130 V and existing B1 130V.
(1) No B1 (130 V) voltage (voltage of network 220 V ac)
These failures may be caused by power supply switch.
0V
0V
Check C809,N804
at
condition of
short-circuit?
Check C809(+) voltage
Y
Check voltage+B
0V
300V
Check N804(5)
voltage
1.5V
Replace the
parts of
failure
Check R812 N804
Check V708 b voltage
0.7V0
Check N501
(2) Existing B1 130 V
These failures may be caused by abnormal operation of horizontal scan, to confirm which can
observe the filament of tube whether bright on. If determined horizontal scan in abnormal operation, look
for the failure start from the horizontal drive stage. Search upward to TMPA8859 with method of
checking DC voltage and waveform according to sequence: PIN13/H.OUT port→ PIN17 power supply→
V707/9V output.
Check VD855 VD854
VD851 VD852 C851
C861 C863 C855
10
N
Check (15V)
voltage
Check voltage at 17 pin of
TMPA8859 =9 V
Y
Check voltage at 13
pin of TMPA8859
=1.9 V
15V0
Y
N
Check VD852 Check V401 T401
Check V707 V706
V705
T402
Check N501
6.2 Existing grating and no picture
Check OSD on screen
NY
Check the voltage of PIN29
36 44 49 of N501
Normal
Check V2in waveform
existed at PIN24 of N501
Abnormal
Check N801 N802
Check N803 N501 G701
Check N501
Y
Check TVin waveform
at N001/PIN2
N
* Whenever open or
interconnect on the bus from
2
CPU to E
chip, no picture can occur.
PROM and main
NY
Check N001
Check circuit between
PIN41~PIN42 of N501
11
6.3 Existing grating and picture, no sound
Abnormal
Check waveform at
pin2 4 of N602
Y
Check N602
R880
Y
Check N602
V603 V604
6.4 Cannot save channels
Y
Check N501
Y
Check SYNC waveform
at N501/PIN62
Check SYNC waveform at
V703 V704 N001/PIN22
Check the audio signal of + pins of
Check waveform
at pin5 7 of N601
When searching automatically channels,
observe whether can display picture
two loudspeaker
N
Check waveform
at pin1 3 of N001
Y N
Check N001
N
Y
Check tuner
CheckN501 V702Check R863 and VD713
Check loudspeaker
N
Check VT voltage of
TUNER=0--30 V
Check 33 V of
Y
Normal
Check N501
V605 C601
N
N
voltage
N
6.5 CPU non-operating
N
Check N803
VD852
Check voltage at PIN9 54 of N501 =5V
N501/PIN5
Y
Check N701 G701
12
Y
Check voltage at
(RESET)=5V
Check V701 VD701
N
Circuit Diagram of TMPA8829-E-KD Color TV Receiver