Sanyo PLC-XP18N, PLC-XP21N User Manual

Multimedia Projector

MODEL PLC-XP21N

Owner's
Manual

PLC-XP18N

2

WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.
This Projector has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the

power outlet. Do not try to defeat this safety feature.
This projector produces intense light from the projection lens. Do not stare directly into the lens as possible eye

damage could result. Be especially careful that children do not stare directly into the beam.

The Remote Control Unit, supplied to this projector, emits the laser beam as the Laser Pointer function from the
Laser Light Window while pressing the LASER button (for 1 minute). Do not look into the Laser Light Window or
shine the laser beam on yourself or other people. Eye damage may result.

This projector should be set in the way indicated. If not, it may result in fire hazard.
If the Projector will not be used for an extended time, unplug the new Projector from the power outlet.

READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.

As the owner of a new Multi-media Projector, you are probably eager to try out your new projector. Before you do, we
suggest that you spend a little time reading this manual to familiarize yourself with the operating procedures, so that you
will receive maximum satisfaction from the many features included in your new projector.
This owner's manual will acquaint you with your projector's features. Reading it will help us too. Through the years, we
have found that many service requests were not caused by problems with our projectors. They were caused by problems
that could have been prevented, if the owner had followed the instructions in the manual.
You can often correct operating problems yourself. If your projector fails to work properly, see "TROUBLESHOOTING"
section on pages 51 ~ 52 and try the solutions marked for each problem.

SAFETY PRECAUTIONS

TO THE OWNER

INFORMATION TO THE USER

NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE CONSTITUTING
A RISK OF ELECTRIC SHOCK IS
PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE
ARE IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS IN THE
OWNER'S MANUAL WITH THIS UNIT.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

PROJECTOR

(FRONT)

PROJECTOR

(SIDE)

WALL

50cm

20cm

50cm50cm

Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:

a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the

operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified technician
to restore the projector to normal operation.

e. If the projector has been dropped or the cabinet has been

damaged.

f. When the projector exhibits a distinct change in

performance-this indicates a need for service.

When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.

Upon completion of any service or repairs to this projector,
ask the service technician to perform routine safety checks
to determine that the projector is in safe operating condition.

This projector is equipped with a
grounding type AC line plug.
Should you be unable to insert the
plug into the outlet, contact your
electrician. Do not defeat the safety
purpose of this grounding type plug.

Follow all warnings and instructions marked on the
projectors.

For added protection to the projector during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will
prevent damage due to lightning and powerline surges.

An appliance and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the appliance
and cart combination to overturn.

If the projector is to be built into a compartment or similarly
enclosed, the minimum distances must be maintained.

Do not cover the ventilation slot on the projector.
Heat build-up can reduce the service life of your projector,

and can also be dangerous.

3

IMPORTANT SAFETY INSTRUCTIONS

All the safety and operating instructions should be read
before the product is operated.

Read all of the instructions given here and retain them for
later use. Unplug this projector from AC power supply
before cleaning. Do not use liquid or aerosol cleaners. Use
a damp cloth for cleaning.

Do not use attachments not recommended by the
manufacturer as they may cause hazards.

Do not place this projector on an unstable cart, stand, or
table. The projector may fall, causing serious injury to a
child or adult, and serious damage to the projector. Use
only with a cart or stand recommended by the
manufacturer, or sold with the projector. Wall or shelf
mounting should follow the manufacturer's instructions,
and should use a mounting kit approved by the
manufacturer.

Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...

Slots and openings in the back and bottom of the cabinet
are provided for ventilation, to insure reliable operation of
the equipment and to protect it from overheating.

The openings should never be covered with cloth or other
material, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or
over a radiator or heat register.

This projector should not be placed in a built-in installation
such as a bookcase unless proper ventilation is provided.

This projector should be operated only from the type of
power source indicated on the marking label. If you are not
sure of the type of power supplied, consult your authorized
dealer or local power company.

Do not overload wall outlets and extension cords as this
can result in fire or electric shock. Do not allow anything to
rest on the power cord. Do not locate this projector where
the cord may be damaged by persons walking on it.

Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points
or short out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the projector.

Do not attempt to service this projector yourself as opening
or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service
personnel.

GROUND

4

TABLE OF CONTENTS

PAGE

PAGE

MENU OPERATION 30-31

MODE SELECT 30
SOUND ADJUSTMENT 31
LANGUAGE ADJUSTMENT 31

VIDEO MODE 32-35

COLOR SYSTEM SELECT 32
VIDEO SOURCE SELECT 33
PICTURE IMAGE ADJUSTMENT 34
PICTURE SCREEN ADJUSTMENT 35

COMPUTER MODE 36-48

COMPUTER SYSTEM SELECT 36
COMPATIBLE COMPUTER SPECIFICATIONS 37
AUTO IMAGE FUNCTION 38
PICTURE IMAGE ADJUSTMENT 39
PICTURE POSITION ADJUSTMENT 40
PC ADJUSTMENT 41-44
PICTURE SCREEN ADJUSTMENT 45

OTHER FUNCTION SETTING 46-48

BLUE BACK 46-47
DISPLAY 46-47
CEILING 46-47
REAR 46-47
SPLIT WIPE 46-47
POWER MANAGEMENT 46-47
REMOTE CONTROL (Mode 1 or Mode 2) 46-47
LAMP AGE 48

APPENDIX 49-53

MAINTENANCE 49-51

TEMPERATURE WARNING INDICATOR 49
AIR FILTER CARE AND CLEANING 49
LAMP REPLACEMENT 50
CLEANING THE LENS 51

TROUBLESHOOTING 51-52
TECHNICAL SPECIFICATIONS 53

FEATURES AND DESIGN 5

COMPATIBILITY 5
IMAGE RESOLUTION 5

AUTOMATIC MULTISCANNING SYSTEM 5
MULTILANGUAGE MENU DISPLAY 5
LASER POINTER FUNCTION 5
OTHER FEATURES 5
UNPACKING THE PROJECTOR 5
TRADEMARKS 5

INSTALLATION 6-9

NAME OF EACH PART OF THE PROJECTOR 6
SETTING-UP THE PROJECTOR 7
MOVING THE PROJECTOR 8
POWER REQUIREMENTS 9

CONNECTING THE PROJECTOR 10-18

TERMINAL OF THE PROJECTOR 10
CONNECTING THE COMPUTER 11-15
CONNECTING THE VIDEO EQUIPMENT 16-18

BEFORE OPERATION 19-26

CONTROLS AND INDICATORS 19-20
OPERATION OF THE REMOTE CONTROL 21-23

CONTROL THE PROJECTOR 24-26

DIRECT OPERATION 24
MENU OPERATION 25-26

BASIC OPERATION 27-31

TURNING ON/OFF THE PROJECTOR 27
DIRECT OPERATION 27-29

MODE SELECT 27
SOUND VOLUME ADJUSTMENT 28
SOUND MUTE FUNCTION 28
ZOOM ADJUSTMENT 28
FOCUS ADJUSTMENT 28
DIGITAL ZOOM FUNCTION 28
KEYSTONE FUNCTION 28
NO SHOW FUNCTION 29
FREEZE PICTURE FUNCTION 29
AUTO IMAGE FUNCTION 29
NORMAL PICTURE FUNCTION 29
P-TIMER FUNCTION 29

5

FEATURES AND DESIGN

The projector is a multimedia projector that combines powerful and sophisticated features with easy-to-use, intuitive
controls. Built-in multimedia features include audio, a palette of 16.77 million colors and active matrix liquid crystal
display (LCD) technology. The projector is ideal for high-performance business, training and imaging applications that
demand exceptional color quality.

COMPATIBILITY

IMAGE RESOLUTION

UNPACKING THE PROJECTOR

TRADEMARKS

AUTOMATIC MULTISCANNING SYSTEM

MULTILANGUAGE MENU DISPLAY

The projector is compatible with many different types of
personal computers and video devices, including:

● IBM-compatible computers, including laptops, up to
1280 x 1024 resolution.

● Apple Macintosh and PowerBook computers up to
1280 x 1024 resolution.

● Various VCRs, video disc players, video cameras,
DVD players, satellite TV tuners or other AV
equipment using any of the worldwide video
standards, including NTSC, NTSC4.43, PAL, PAL-M,
PAL-N and SECAM.

The resolution of the projector's projected image is 1024
x 768. The projector displays computer images just as
they appear on your computer's monitor. Screen
resolutions between 1024 x 768 and 1280 x 1024 are
compressed to 1024 x 768. The projector cannot display
screen resolutions above 1280 x 1024. If your computer's
screen resolution is higher than 1280 x 1024, reset it to a
lower resolution before you connect the projector.

This projector can detect display signals from most
personal computers currently distributed. It is free from
complicated adjustments to project picture images from
PC.

The projector comes with the parts listed below. Check to
find all the parts are included. If any parts are missing,
contact an authorized dealer or service station.

● Owner's Manual.

● AC Power Cord.

● Remote Control Unit.

● Batteries for Remote Control Units.

● VGA Cable.

● Mouse Cable for PS/2 port.

● Mouse Cable for serial port.

● Mouse Cable for ADB port.

● VGA/MAC Adapter.

● Protective Dust Cover.

● Lens Cover.

● Apple, Macintosh, and PowerBook are trademarks or

registered trademarks of Apple Computer, Inc.

● IBM and PS/2 are trademarks or registered trademarks
of International Business Machines, Inc.

● Windows is a trademarks or registered trademarks of
Microsoft Corporation.

● Other trademarks are the property of their respective
owners

LASER POINTER FUNCTION

The Remote Control Unit of this projector includes the
Laser Pointer function providing the ability to point and
highlight during presentations.

OTHER FEATURES

This projector has Motor Zoom/Focus, No Show, Picture
Freeze, Keystone, Mute Functions.

MENU DISPLAY is displayed with ; English, German,
French, Italian, Spanish and Japanese.

INFRARED
REMOTE
RECEIVER

6

EXHAUST VENT

CAUTION HOT AIR!
Air blown from the exhaust vent is hot.
Observe the following when handling your

projector or choosing a location to install it.

● Keep heat-sensitive objects away from the
exhaust port.

● If you set the projector on top of a metallic
surface, the surface will become hot because of
the hot air exhaust. Be careful when handling.

● Do not touch the cabinet near to the exhaust
vent area, and especially screws and metallic
parts. These parts will become hot while the
projector is used.

FRONT OF THE PROJECTOR

REAR OF THE PROJECTOR

SPEAKERS

INFRARED
REMOTE
RECEIVER

PROJECTION LENS

REMOVABLE
LENS COVER

MAIN ON/OFF
SWITCH

CARRYING
HANDLE

POWER CORD
CONNECTOR

ADJUSTABLE
FEET

AIR INTAKE VENT

BOTTOM OF THE PROJECTOR

LAMP
COVER

NAME OF EACH PART OF THE PROJECTOR

INSTALLATION

AIR INTAKE VENT

FEET LOCK
LATCH

FEET LOCK
LATCH

100"

60"

40"

150"

200"

250"

77"

46"

31"

115"

154"

192"

H1

H2

231"

300"

400"

308"

7

POSITIONING:

ROOM LIGHT

● This projector is basically designed to project on a flat projection surface.

● This projector can be focused from 4.6' (1.4 m) ~ 47.3' (14.4 m).

● Refer to the figure below as an example when positioning the projector to the screen.

Minimum Zoom

Maximum Zoom

DISTANCE

SETTING-UP THE PROJECTOR

INSTALLATION

This projector is equipped with cooling fan to protect it from
overheating. Pay attention to the following to ensure proper
ventilation and avoid a possible risk of fire and malfunction.

● Do not cover the vents with papers or other materials.

●

Keep the rear grill at least 3 feet (1 m) away from any
object.

● Make sure that there are no objects under the projector.
An object under the projector may prevent the projector
from taking the cooling air through the bottom vent.

VENTILATION

AIR INTAKE VENT
(BOTTOM SIDE)

EXHAUST VENT
(REAR SIDE)

400"
308"

47.3' (14.4m)

Screen
Size

Max. Zoom
Min. Zoom

Distance

40"
31"

4.6' (1.4m)

60"
46"

7.2' (2.2m)

100"

77"

11.8' (3.6m)

150"
115"

17.7' (5.4m)

200"
154"

23.6' (7.2m)

250"
192"

29.5' (9.0m)

300"
231"

35.4' (10.8m)

Screen Size
(W x H) inch

Height (H1)
Height (H2)

40"

32 x 24

22.8 inch

1.2 inch

60"

48 x 36

34.2 inch

1.8 inch

100"

80 x 60

57.1 inch

2.9 inch

150"

120 x 90

85.7 inch

4.3 inch

200"

160 x 120

114.3 inch

5.7 inch

250"

200 x 150

142.8 inch

7.2 inch

300"

240 x 180

171.4 inch

8.6 inch

400"

320 x 240

228.6 inch

11.4 inch

The level of brightness in a room has a great
influence on picture quality. It is recommended
to limit ambient lighting in order to provide the
best image.

DOWN

CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR

● Do not drop or bump the projector, otherwise damages or malfunctions may result.

● When transporting the projector, use a Sanyo recommended Carrying Case.

● Do not transport the projector by using a courier or transport service in an unsuitable transport case. This may cause

damage to the projector. To transport the projector through a courier or transport service, use a Sanyo recommended
Case.

● For a carrying or transportation cases, contact a Sanyo authorized dealer.

8

Use the carrying handle when moving the projector.
Replace the lens cover and retract the adjustable feet when
moving the projector to prevent damage to the projector.

ADJUSTABLE
FEET

FEET LOCK LATCHES

MOVING THE PROJECTOR

INSTALLATION

UP

UP

DOWN

Picture tilt and projection angle can be adjusted by rotating the
ADJUSTABLE FEET. Projection angle can be adjusted 0 to 6°.

ADJUSTABLE FEET

Lift the front of the projector and press the FEET LOCK
LATCHES on both sides of the projector.

Release the FEET LOCK LATCHES to lock the ADJUSTABLE
FEET and rotate the ADJUSTABLE FEET to fine tune the
position and the tilt.

To shorten the ADJUSTABLE FEET, lift the front of the
projector and press and undo the FEET LOCK LATCHES.

1.

3.

2.

NOTE: The position and the keystone distortion of the image can

also be adjusted using the KEYSTONE function.

(See pages 28, 35 and 45).

9

INSTALLATION

POWER REQUIREMENTS

Your projector uses nominal input voltages of 100-120 VAC. The projector
automatically selects the correct input voltage. The projector is designed to work
with single-phase power systems having a grounded neutral conductor. To reduce
the risk of electrical shock, do not plug into any other type of power system.
Consult your authorized dealer or service station if you are not sure what type of
power is supplied to your building.

Connect the AC power supply cord
(supplied) to the projector.
The socket-outlet must be near this
equipment and must be easily
accessible.

Projector side (Female)

AC outlet side (Male)

10

REAR OF THE PROJECTOR

AUDIO INPUT JACKS

Used to connect an audio input to the projector.

VIDEO INPUT JACK

Used to connect a video source to the projector.

S-VIDEO INPUT JACK

Used to connect a S-VHS video source to the
projector.

COMPONENT VIDEO INPUT JACKS

Used to connect a component video source to the
projector.

EXT. SP. JACK (3.5 mm mini stereo type)

Used to connect an external speaker system.

Y Cb/Pb Cr/Pr

COMPUTER IN 1

COMPUTER IN 2

MONITOR OUT

EXT. SP

CONTROL PORT 2

CONTROL PORT 1

AUDIO 2

(STEREO)

(STEREO)

AUDIO 1

(STEREO)

(8Ω)

AUDIO

VIDEO

S-VIDEO

(MONO)

R L

AV IN

COMPUTER



1

2

3

6
7

10

9

4

5

8

11

12

1
2
3
4

5
6

8
9

10

11

12

7

CONNECTING THE PROJECTOR

TERMINAL OF THE PROJECTOR

COMPUTER INPUT-1 TERMINAL

Used to connect a computer to the projector.

COMPUTER INPUT-2 TERMINAL

Used to connect a computer to the projector.

MONITOR OUTPUT TERMINAL

Used to connect a monitor to the projector.

COMPUTER AUDIO INPUT-1 JACK
mini stereo type

Used to connect a computer audio input to the projector.

CONTROL PORT-1 CONNECTOR

Used to connect a mouse cable to the projector.

COMPUTER AUDIO INPUT-2 JACK
mini stereo type

Used to connect a computer audio input to the projector.

CONTROL PORT-2 CONNECTOR

Used to connect a mouse cable to the projector.

NOTE: Control port-2 connector can be also used as

serial port (RS-232C).

11

CONNECTING THE PROJECTOR

CONNECTING THE COMPUTER

Personal computers can be connected to the HDB15-pin (VGA) terminal on the projector.

● Connect the computer to these terminals using the VGA cable and VGA/Macintosh adapter (provided).
CAUTION: For projectors, the VGA cable provided is designed to reduce RFI (Radio Frequency Interference) emissions.

For regulatory compliance reasons, this cable must be used and must not be replaced by any other cable.

CONNECTING TO THE COMPUTER INPUT TERMINALS (1 and 2)

CONNECTING TO THE COMPUTER AUDIO INPUT JACKS (1 and 2)

CONNECTING TO THE CONTROL PORT (DIN 8 PIN) CONNECTORS (1 and 2)

54321

109876

15 14 13 12 11

This terminal output the information of the selected computer source being viewed on the screen (Computer 1 or Computer 2).
When video source is selected, this terminal outputs Computer 1 input information.

An external monitor can be connected to the HDB15-pin (VGA) terminal on the projector.

● Connect the monitor to this terminal using the VGA cable (not provided).

Pin No./Signal

1 Red input
2 Green input
3 Blue input
4 Sense 2
5 Ground (Horiz.sync.)
6 Ground (Red)
7 Ground (Green)
8 Ground (Blue)

Pin No./Signal

9 Non Connect
10 Ground (Vert. sync.)
11 Sense 0
12 Sense 1
13 Horiz. sync
14 Vert. sync
15 Reserved

HDB 15-PIN
TERMINAL

CONNECTING TO THE MONITOR OUTPUT TERMINAL

● Connect audio outputs from your computer to these jacks using the audio cable (not provided).

● If you wish to control the computer with projector's remote control unit, you must connect control port (PS/2, Serial or

ADB port) on your computer to projector's control port with cable. (three type cables supplied; for PS/2 Port, Serial Port
and ADB Port).

6

3

8

1

2

7

45

■ CONTROL PORT

––––––––

ADB

––––––––

GND

––––––––
––––––––
––––––––

GND

RXD

––––––––
––––––––

GND

RTS/CTS

TXD
GND
GND

–––––––-

CLK

DATA

GND

––––––––
––––––––

GND

––––––––

Serial Port

ADB Port

1
2
3
4
5
6
7
8

PS/2 Port

NOTE: The RXD port (1 pin on the Serial Port) is provided on control port 2 connector only. If you control the projector by

computer, you must connect control port 2 connector.

12

CONNECTING THE PROJECTOR

Y Cb/Pb Cr/Pr

COMPUTER IN 1

COMPUTER IN 2

MONITOR OUT

EXT. SP

CONTROL PORT 2

CONTROL PORT 1

AUDIO 2

(STEREO)

(STEREO)

AUDIO 1

(STEREO)

(8Ω)

AUDIO

VIDEO

S-VIDEO

(MONO)

R L

AV IN COMPUTER

COMPUTER
OUTPUT

COMPUTER

MONITOR CABLE
(NOT PROVIDED)

SERIAL PORT
INPUT

MONITOR
OUTPUT

COMPUTER
AUDIO INPUT
1 or 2

MOUSE CABLE FOR
PS/2 PORT
(PROVIDED)

MOUSE CABLE FOR
SERIAL PORT
(PROVIDED)

PS/2 PORT
INPUT

VGA CABLE
(PROVIDED)

AUDIO CABLE
(NOT PROVIDED)

EXTERNAL AUDIO
EQUIPMENT
(Refer to page 18)

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be

disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.

COMPUTER
INPUT 1 or 2

CONNECTING AN IBM-COMPATIBLE DESKTOP COMPUTER

AUDIO
OUTPUT

CONTROL PORT
OUTPUT 1 or 2

13

CONNECTING THE PROJECTOR

Y Cb/Pb Cr/Pr

COMPUTER IN 1

COMPUTER IN 2

MONITOR OUT

EXT. SP

CONTROL PORT 2

CONTROL PORT 1

AUDIO 2

(STEREO)

(STEREO)

AUDIO 1

(STEREO)

(8Ω)

AUDIO

VIDEO

S-VIDEO

(MONO)

R L

AV IN

COMPUTER

COMPUTER

SERIAL PORT
INPUT

PS/2 PORT
INPUT

AUDIO CABLE
(NOT PROVIDED)

VGA CABLE
(PROVIDED)

MOUSE CABLE FOR
PS/2 PORT
(PROVIDED)

MOUSE CABLE FOR
SERIAL PORT
(PROVIDED)

COMPUTER
OUTPUT

CONTROL PORT
OUTPUT 1 or 2

CONNECTING AN IBM-COMPATIBLE LAPTOP COMPUTER

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be

disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.

EXTERNAL AUDIO
EQUIPMENT
(Refer to page 18)

AUDIO
OUTPUT

COMPUTER
AUDIO INPUT
1 or 2

COMPUTER
INPUT 1 or 2

123456

ON

Y Cb/Pb Cr/Pr

COMPUTER IN 1

COMPUTER IN 2

MONITOR OUT

EXT. SP

CONTROL PORT 2

CONTROL PORT 1

AUDIO 2

(STEREO)

(STEREO)

AUDIO 1

(STEREO)

(8Ω)

AUDIO

VIDEO

S-VIDEO

(MONO)

R L

AV IN

COMPUTER

14

CONNECTING THE PROJECTOR

COMPUTER

MONITOR CABLE
(NOT PROVIDED)

COMPUTER
OUTPUT

VGA/MAC ADAPTER
(PROVIDED)

CONNECTING A MACINTOSH DESKTOP COMPUTER

ON

2

34

5

61

ON

OFF

VGA/MAC ADAPTER

SW1 ~ SW6

Set the dip switches as shown in the table below depending on
the RESOLUTION MODE that you want to use before you turn
on the projector and computer.

ADB PORT
INPUT

SW1

ON
OFF
OFF

ON

RESOLUTION MODE
13" MODE (640

x

480)

16" MODE (832

x

624)

19" MODE (1024

x

768)

21" MODE (1152

x

870)

SW6

OFF
OFF
OFF
OFF

SW5

OFF
OFF
OFF
OFF

SW4

OFF

ON

OFF

ON

SW3
OFF
OFF

ON
ON

SW2

ON
ON
ON
ON

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be

disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.

AUDIO
OUTPUT

EXTERNAL AUDIO
EQUIPMENT
(Refer to page 18)

MOUSE CABLE FOR
ADB PORT
(PROVIDED)

AUDIO CABLE
(NOT PROVIDED)

COMPUTER
AUDIO INPUT
1 or 2

CONTROL PORT
OUTPUT 1 or 2

COMPUTER
INPUT 1 or 2

MONITOR
OUTPUT

VGA CABLE
(PROVIDED)

15

123456

ON

Y Cb/Pb Cr/Pr

COMPUTER IN 1

COMPUTER IN 2

MONITOR OUT

EXT. SP

CONTROL PORT 2

CONTROL PORT 1

AUDIO 2

(STEREO)

(STEREO)

AUDIO 1

(STEREO)

(8Ω)

AUDIO

VIDEO

S-VIDEO

(MONO)

R L

AV IN

COMPUTER

COMPUTER

AUDIO
OUTPUT

ADB PORT
INPUT

VGA/MAC ADAPTER
(PROVIDED)

VGA CABLE
(PROVIDED)

MOUSE CABLE FOR
ADB PORT
(PROVIDED)

COMPUTER
INPUT 1 or 2

COMPUTER
AUDIO INPUT 1 or 2

AUDIO CABLE
(NOT PROVIDED)

CONNECTING A MACINTOSH POWERBOOK COMPUTER

CONNECTING THE PROJECTOR

NOTE: The Macintosh PowerBook requires the use of the PowerBook Video

Adapter shipped with the PowerBook.

ON

2

34

5

61

ON

OFF

VGA/MAC ADAPTER

SW1 ~ SW6

Set the dip switches as shown in the table below depending on
the RESOLUTION MODE that you want to use before you turn
on the projector and computer.

SW1

ON
OFF
OFF

ON

RESOLUTION MODE
13" MODE (640

x

480)

16" MODE (832

x

624)

19" MODE (1024

x

768)

21" MODE (1152

x

870)

SW6

OFF
OFF
OFF
OFF

SW5

OFF
OFF
OFF
OFF

SW4

OFF

ON

OFF

ON

SW3
OFF
OFF

ON
ON

SW2

ON
ON
ON
ON

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be

disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.

CONTROL PORT
OUTPUT 1 or 2

EXTERNAL AUDIO
EQUIPMENT
(Refer to page 18)

TO POWERBOOK
VIDEO ADAPTER

16

CONNECTING THE VIDEO EQUIPMENT

CONNECTING THE PROJECTOR

Connect the S-VIDEO output from the video equipment to this jack using the S-video cable.
The S-VIDEO jack has priority over the VIDEO (composite) jack.

CONNECTING TO THE VIDEO INPUT JACK

CONNECTING S-VHS VIDEO INPUT JACK

Connect to the video and audio outputs of a VCR, video disc player, DVD player, video camera, satellite TV tuner or other
AV equipment.

CONNECTING TO THE COMPONENT VIDEO INPUT JACKS

Connect the component video outputs (Y, Cb/Pb, Cr/Pr) from the DVD player or other video equipment to these jacks
using the video cable.
The COMPONENT VIDEO jack has priority over the S-VIDEO and VIDEO (composite) jacks.

Connect the video output from the video equipment to this jack using the video cable.

Connect the audio outputs from the video equipment to these jacks using the audio cable.
When the audio output is monaural, connect it to the L (mono) jack.

CONNECTING TO THE AUDIO INPUT JACKS

17

Y Cb/Pb Cr/Pr

COMPUTER IN 1

COMPUTER IN 2

MONITOR OUT

EXT. SP

CONTROL PORT 2

CONTROL PORT 1

AUDIO 2

(STEREO)

(STEREO)

AUDIO 1

(STEREO)

(8Ω)

AUDIO

VIDEO

S-VIDEO

(MONO)

R L

AV IN

COMPUTER

VIDEO EQUIPMENT

Video Cassette Recorder

DVD Player
Video Disc Player

Satellite
TV Tuner

DVD Player

S-VIDEO
OUTPUT

S-VIDEO
INPUT

AUDIO
INPUT

Video Camera

VIDEO
OUTPUT

L R
AUDIO
OUTPUT

VIDEO INPUT

AUDIO INPUT

AUDIO
OUTPUT

Y, Cb/Pb, Cr/Pr
COMPONENT
VIDEO OUTPUT

R L
AUDIO
OUTPUT

AUDIO
INPUT

COMPONENT
VIDEO INPUT

CONNECTING THE PROJECTOR

CONNECTING THE VIDEO EQUIPMENT

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be

disconnected from AC outlet. Turn the projector on before the peripheral equipment is switched on.

VCR Etc...