How it Works
Sanyo
Loading...
P
Loading...
Loading...
PLC-XM100/L - 5000 Lumens
User Manual
79 pgs677.71 Kb0

Sanyo PLC-XM100/L - 5000 Lumens, PLC-XM150/L - 6000 Lumens, PLC-XM100, PLC-XM150, PLC-XM100L User Manual

...
EXPAND SERIAL COMMAND
FUNCTIONAL SPECIFICATIONS
PLC-XM100
PLC-XM150 PLC-XM100L PLC-XM150L
Ver.1.0
DS Company
Projector Division
PLC-XM100/XM100L/XM150/XM150L Expand Serial Command Functional Specifications
Contents
1． Overview .........................................................................................................................9
2． Serial Interface Specification........................................................................................9
2.1 Transfer Specification .................................................................................................9
2.2 Connection ...................................................................................................................9
3． Notes for communication............................................................................................10
4． Notation Convention....................................................................................................10
5． Functional Execution Command Table......................................................................11
5.1 Image Command Table..............................................................................................11
5.2 PC Adjust Control Command Table .........................................................................11
5.3 Input Control Command Table .................................................................................11
5.4 Screen Control Command Table ..............................................................................12
5.5 Lamp Command Table ..............................................................................................12
5.6 Sound Command Table.............................................................................................12
5.7 Setting Command Table............................................................................................12
5.8 Other Command Table ..............................................................................................13
6． Status Read Command Table......................................................................................14
6.1 Image Status Read Command Table........................................................................14
6.2 PC Adjust Status Read Command Table.................................................................14
6.3 Video Status Read Command Table ........................................................................14
6.4 Input Status Read Command Table .........................................................................14
6.5 Screen Status Read Command Table......................................................................15
6.6 Lamp Status Read Command Table.........................................................................15
6.7 Sound Status Read Command Table .......................................................................15
6.8 Setting Status Read Command Table......................................................................15
6.9 Other Status Read Command Table.........................................................................16
7． Error Code Table ..........................................................................................................16
8． Functional Execution Command................................................................................17
8.1 Format.........................................................................................................................17
8.2 Transfer Example.......................................................................................................17
8.3 Operation Requirements ...........................................................................................17
8.4 Image Command ........................................................................................................18
8.4.1 CF_ BRIGHT Command......................................................................................18
8.4.2 CF_CONT Command...........................................................................................18
8.4.3 CF_COLOR Command........................................................................................18
8.4.4 CF_TINT Command .............................................................................................18
8.4.5 CF_SHARP Command ........................................................................................19
8.4.6 CF_GAMMA Command.......................................................................................19
8.4.7 CF_WBAL- Command.........................................................................................19
8.4.8 CF_COLTEMP Command ...................................................................................20
2/79
PLC-XM100/XM100L/XM150/XM150L Expand Serial Command Functional Specifications
8.4.9 CF_OFFSET- Command .....................................................................................20
8.4.10 CF_NZRED Command ......................................................................................20
8.4.11 CF_PROGV Command......................................................................................21
8.4.12 CF_IMAGE Command.......................................................................................21
8.4.13 CF_IMAGEADJ Command................................................................................22
8.5 PC Adjust Control Command ...................................................................................23
8.5.1 CF_FSYNC Command.........................................................................................23
8.5.2 CF_TDOTS Command.........................................................................................23
8.5.3 CF_CLPPHASE Command.................................................................................23
8.5.4 CF_H-POS Command .........................................................................................24
8.5.5 CF_V-POS Command..........................................................................................24
8.5.6 CF_DDOTS Command ........................................................................................24
8.5.7 CF_DLINE Command..........................................................................................25
8.5.8 CF_SETPCADJ Command .................................................................................25
8.5.9 CF_ORGMODE Command..................................................................................26
8.5.10 CF_PCSTORE Command .................................................................................26
8.5.11 CF_PCMODEFREE Command .........................................................................27
8.6 Input Control Command............................................................................................28
8.6.1 CF_INPUT Command..........................................................................................28
8.6.2 CF_SOURCE Command .....................................................................................28
8.6.3 CF_INPUT 1 Command.......................................................................................29
8.6.4 CF_INPUT 2 Command.......................................................................................29
8.6.5 CF_INPUT 3 Command.......................................................................................29
8.6.6 CF_INPUT 4 Command.......................................................................................29
8.6.7 CF_SYSTEM Command......................................................................................30
8.7 Screen Control Command ........................................................................................31
8.7.1 CF_SCREEN Command......................................................................................31
8.7.2 CF_DZCENT Command ......................................................................................31
8.7.3 CF_KEYSTONE Command .................................................................................32
8.7.4 CF_KYSTONMODE Command...........................................................................32
8.7.5 CF_CORNER-UL Command ...............................................................................32
8.7.6 CF_CORNER-UR Command...............................................................................33
8.7.7 CF_CORNER-DL Command ...............................................................................33
8.7.8 CF_CORNER-DR Command...............................................................................33
8.7.9 CF_CORNERTESTPAT Command.....................................................................34
8.7.10 CF_CEIL Command...........................................................................................34
8.7.11 CF_REAR Command.........................................................................................34
8.7.12 CF_VSCALE Command ....................................................................................35
8.7.13 CF_VPOS Command.........................................................................................35
8.7.14 CF_HSCALE Command....................................................................................36
3/79
PLC-XM100/XM100L/XM150/XM150L Expand Serial Command Functional Specifications
8.7.15 CF_HPOS Command.........................................................................................36
8.8 Lamp Command.........................................................................................................37
8.8.1 CF_LAMPMODE Command................................................................................37
8.8.2 CF_LAMPLIFECONTRL_ Command .................................................................37
8.9 Sound Command.......................................................................................................38
8.9.1 CF_VOLUME Command .....................................................................................38
8.9.2 CF_MUTE Command...........................................................................................38
8.9.3 CF_BLTINSP Command......................................................................................38
8.10 Setting Command ....................................................................................................39
8.10.1 CF_LANG Command.........................................................................................39
8.10.2 CF_MENUPOSITION Command.......................................................................39
8.10.3 CF_INPUTBUTTON Command.........................................................................39
8.10.4 CF_DISP Command ..........................................................................................40
8.10.5 CF_BACKGND Command ................................................................................40
8.10.6 CF_LOGO Command ........................................................................................41
8.10.7 CF_FILH Command...........................................................................................41
8.10.8 CF_FILTIMER Command ..................................................................................41
8.10.9 CF_FILCTL Command ......................................................................................41
8.10.10 CF_FILSCRL Command .................................................................................42
8.10.11 CF_FANSPEED Command .............................................................................42
8.10.12 CF_SIMPLEMODE Command ........................................................................42
8.10.13 CF_RCODE Command....................................................................................42
8.10.14 CF_RSENS Command ....................................................................................43
8.10.15 CF_P-MANE Command ..................................................................................43
8.10.16 CF_P-MANETIME Command..........................................................................43
8.10.17 CF_STANDBYMODE Command.....................................................................44
8.10.18 CF_ON-STA Command ...................................................................................44
8.10.19 CF_POINTER Command.................................................................................44
8.10.20 CF_PTIMEMODE Command...........................................................................44
8.10.21 CF_PTIMER Command...................................................................................45
8.10.22 CF_PTIME Command......................................................................................45
8.10.23 CF_KEYDIS Command ...................................................................................45
8.10.24 CF_PJPINCODE Command............................................................................46
8.10.25 CF_SHUTRCPROT Command........................................................................46
8.10.26 CF_SHUTKEYPROT Command .....................................................................46
8.10.27 CF_SHUTH Command ....................................................................................47
8.10.28 CF_DELAYCTRL Command ...........................................................................47
8.10.29 CF_TESTPAT Command.................................................................................47
8.10.30 CF_FDEFAULT Command ..............................................................................47
8.11 Other Commands.....................................................................................................48
4/79
PLC-XM100/XM100L/XM150/XM150L Expand Serial Command Functional Specifications
8.11.1 CF_KEYEMU Command....................................................................................48
8.11.2 CF_MENU Command ........................................................................................48
8.11.3 CF_POWER Command .....................................................................................49
8.11.4 CF_FREEZE Command.....................................................................................49
8.11.5 CF_VMUTE Command ......................................................................................49
9． Status Read Command ............................................................................................50
9.1 Format.........................................................................................................................50
9.2 Transfer Example.......................................................................................................50
9.3 Operation Condition..................................................................................................50
9.4 Image Status Read Command ..................................................................................50
9.4.1 CR_BRIGHT Command ......................................................................................50
9.4.2 CR_CONT Command ..........................................................................................50
9.4.3 CR_COLOR Command .......................................................................................50
9.4.4 CR_TINT Command ............................................................................................51
9.4.5 CR_SHARP Command........................................................................................51
9.4.6 CR_GAMMA Command ......................................................................................51
9.4.7 CR_WBAL-R Command......................................................................................51
9.4.8 CR_WBAL-G Command .....................................................................................51
9.4.9 CR_WBAL-B Command......................................................................................52
9.4.10 CR_COLTEMP Command.................................................................................52
9.4.11 CR_OFFSET-R Command.................................................................................52
9.4.12 CR_OFFSET-G Command ................................................................................52
9.4.13 CR_OFFSET-B Command ................................................................................52
9.4.14 CR_NZRED Command......................................................................................53
9.4.15 CR_PROGV Command .....................................................................................53
9.4.16 CR_IMAGE Command ......................................................................................53
9.4.17 CR_IMGGMD Command...................................................................................53
9.5 PC Adjust Status Read Command ...........................................................................54
9.5.1 CR_FSYNC Command ........................................................................................54
9.5.2 CR_TDOTS Command ........................................................................................54
9.5.3 CR_CLPPHASE Command.................................................................................54
9.5.4 CR_H-POS Command.........................................................................................54
9.5.5 CR_V-POS Command .........................................................................................55
9.5.6 CR_DDOTS Command........................................................................................55
9.5.7 CR_DLINE Command..........................................................................................55
9.5.8 CR_ORGMODE Command .................................................................................56
9.5.9 CR_PCSTORE Command...................................................................................57
9.5.10 CR_SETPCADJ Command...............................................................................57
9.6 Video Status Read Command...................................................................................58
9.6.1 CR_SERSYS Command......................................................................................58
5/79
PLC-XM100/XM100L/XM150/XM150L Expand Serial Command Functional Specifications
9.7 Input Read Command................................................................................................59
9.7.1 CR_INPUT Command..........................................................................................59
9.7.2 CR_SOURCE Command.....................................................................................59
9.7.3 CR_SRCINP1 Command.....................................................................................59
9.7.4 CR_SRCINP2 Command.....................................................................................59
9.7.5 CR_SRCINP3 Command.....................................................................................60
9.7.6 CR_SRCINP4 Command.....................................................................................60
9.7.7 CR_SYSTEM Command .....................................................................................61
9.7.8 CR_SYSLIST Command .....................................................................................62
9.7.9 CR_MODELIST Command..................................................................................62
9.7.10 CR_HMSLOT Command...................................................................................63
9.7.11 CR_NMSLOT1 Command .................................................................................63
9.7.12 CR_NMSLOT2 Command.................................................................................63
9.7.13 CR_NMSLOT3 Command.................................................................................63
9.7.14 CR_NMSLOT4 Command.................................................................................63
9.7.15 CR_IDSLOT1 Command...................................................................................64
9.7.16 CR_IDSLOT2 Command...................................................................................64
9.7.17 CR_IDSLOT3 Command...................................................................................64
9.7.18 CR_IDSLOT4 Command...................................................................................64
9.8 Screen Status Read Command ................................................................................65
9.8.1 CR_SCREEN Command .....................................................................................65
9.8.2 CR_VSCALE Command......................................................................................65
9.8.3 CR_VPOS Command ..........................................................................................65
9.8.4 CR_HSCALE Command .....................................................................................65
9.8.5 CR_HPOS Command ..........................................................................................65
9.8.6 CR_ KYSTNMODE Command ............................................................................66
9.8.7 CR_CORNERTESTPAT Command.....................................................................66
9.8.8 CR_CEIL Command ............................................................................................66
9.8.9 CR_REAR Command ..........................................................................................66
9.9 Lamp Status Read Command...................................................................................67
9.9.1 CR_LAMPREPL Command ................................................................................67
9.9.2 CR_LAMPH Command........................................................................................67
9.9.3 CR_LAMPCORRESPH Command .....................................................................67
9.9.4 CR_LAMPMODE Command ...............................................................................67
9.9.5 CR_LAMPSTS Command...................................................................................67
9.9.6 CR_PROJH Command........................................................................................68
9.9.7 CR_HMLAMP Command.....................................................................................68
9.9.8 CR_LAMPLIFECONTRL Command ...................................................................68
9.10 Sound Status Read Command ...............................................................................69
9.10.1 CR_VOLUME Command...................................................................................69
6/79
PLC-XM100/XM100L/XM150/XM150L Expand Serial Command Functional Specifications
9.10.2 CR_MUTE Command ........................................................................................69
9.10.3 CR_BLTINSP Command ...................................................................................69
9.11 Setting Status Read Command ..............................................................................70
9.11.1 CR_LANG Command ........................................................................................70
9.11.2 CR_INPUTBUTTON Command.........................................................................70
9.11.3 CR_DISP Command ..........................................................................................70
9.11.4 CR_BACKGND Command ................................................................................70
9.11.5 CR_LOGO Command........................................................................................71
9.11.6 CR_LOGOLOCK Command..............................................................................71
9.11.7 CR_FILREMAIN Command...............................................................................71
9.11.8 CR_FILH Command...........................................................................................71
9.11.9 CR_FILTIMER Command ..................................................................................71
9.11.10 CR_FILCOND Command ................................................................................72
9.11.11 CR_FILREPL Command..................................................................................72
9.11.12 CR_FANSPEED Command .............................................................................72
9.11.13 CR_SIMPLEMODE Command ........................................................................72
9.11.14 CR_RCODE Command....................................................................................72
9.11.15 CR_RSENS Command ....................................................................................73
9.11.16 CR_RTYPE Command.....................................................................................73
9.11.17 CR_P-MANE Command ..................................................................................73
9.11.18 CR_P-MANETIME Command..........................................................................73
9.11.19 CR_STANDBYMODE Command ....................................................................73
9.11.20 CR_ON-STA Command ...................................................................................74
9.11.21 CR_POINTER Command ................................................................................74
9.11.22 CR_PTIMEMODE Command...........................................................................74
9.11.23 CR_PTIMER Command...................................................................................74
9.11.24 CR_PTIME Command......................................................................................74
9.11.25 CR_KEYDIS Command ...................................................................................75
9.11.26 CR_SECURITY Command ..............................................................................75
9.11.27 CR_PJLOCKNOW Command.........................................................................75
9.11.28 CR_PJLOCKMENU Command .......................................................................75
9.11.29 CR_SHUTRCPROT Command .......................................................................75
9.11.30 CR_SHUTKEYPROT Command .....................................................................76
9.11.31 CR_SHUTH Command ....................................................................................76
9.11.32 CR_DELAYCTRL Command ...........................................................................76
9.11.33 CR_TESTPAT Command.................................................................................76
9.12 Other Status Read Commands...............................................................................77
9.12.1 CR_STATUS Command ....................................................................................77
9.12.2 CR_SIGNAL Command.....................................................................................77
9.12.3 CR_VMUTE Command......................................................................................77
7/79
PLC-XM100/XM100L/XM150/XM150L Expand Serial Command Functional Specifications
9.12.4 CR_FREEZE Command ....................................................................................77
9.12.5 CR_TEMPFAIL Command ................................................................................78
9.12.6 CR_TEMP Command ........................................................................................79
9.12.7 CR_SHUTCOND Command..............................................................................79
9.12.8 CR_SERIALNO Command................................................................................79
8/79
PLC-XM100/XM100L/XM150/XM150L Expand Serial Command Functional Specifications
1． Overview
・ This Functional Specification defines communication with PJ-Net organizer for PLC-XM100 /
XM100L / XM150 / XM150L.
・ Supporting Firmware Ver. 1.x of the projector.
・ Commands in this document are to communicate with PJ-Net organizer, but most commands are
used to control a projector remotely from a computer with RS-232C. Therefore commands in this
document are defined as Expand Serial Commands.
2． Serial Interface Specification
2.1 Transfer Specification
Item Specification
Synchronous System Asynchronous
Transmission Speed 9600 / 19200
Data Length 8 bits
Parity N/A
Stop Bit 1
Flow Control N/A
Note1) Transmission Speed: initial setting value is 19200
Note2) Transmission Speed can be changed in Service mode.
2.2 Connection
Dedicated serial cables must be used for the connection between a computer and a projector.
PC Projector
COM 1 CONTROL PORT
(D-Sub 9Pin) (D-Sub 9Pin)
Connect COM port of the computer to CONTROL PORT of the projector.
COM Port (COM1 or COM2) of a computer is specified by control software of the computer.
9/79
PLC-XM100/XM100L/XM150/XM150L Expand Serial Command Functional Specifications
3． Notes for communication
1. Expand Serial Command is defined as a single command per line that starts with “C” and ends
with carriage return (0x0D).
2. There are two types of commands; Functional Execution Commands and Status Read
Command.
- Example of Functional Execution Command: “CF_BRIGHT_032” [CR]
- Example of Status Read Command: “CR_BRIGHT” [CR]
Note) “_” means a space
3. When it takes more than a second to receive a single command, it is not executed.
When it takes more than a second to receive carriage return (0x0D) since the reception of the
first data “C”, it clears the information of the receive buffer.
4. When the command pipelining, allow the interval time of no less than100ms after receiving
return value. (No less than 100 ms)
Command
PC → Projector “CF_BRIGHT_032” CR Next command
Projector → PC “000” CR
Return Value
(A few ms - 5s)
5. Do not send another command before the reception of the return value; the operation by the
command is not ensured.
However this is not the case when no response is returned after more than 5 seconds.
6. It takes about 5 seconds for internal initialization after plugging in AC power. During this time, it
cannot process commands. Do not issue any command.
4． Notation Convention
1. Data from a controller to a projector is represented as COMMAND, and data from a projector to
a controller in response to the incoming command is represented as RESPONSE.
2. [CR]: Carriage Return Code
Carriage Return code is added to the end of the command.
Response is also followed by carriage return code.
3. _: Space Code
Space Code is represented as (_).
4. %1: Parameter included in Command
When there are more than one parameter, they are defined as %2, %3…
5. %%%: Error Code returned from a projector
Acceptable: “000”.
Unacceptable: See [7. Error Code Table].
10/79
PLC-XM100/XM100L/XM150/XM150L Expand Serial Command Functional Specifications
5． Functional Execution Command Table
5.1 Image Command Table
Execute command Item
CF_BRIGHT_%1 [CR] Set value of Brightness CF_CONT_%1 [CR] Set value of Contrast CF_COLOR_%1 [CR] CF_TINT_%1 [CR]
Set value of Color
Set value of Tint
CF_SHARP_%1 [CR] Set value of Sharpness CF_GAMMA_%1 [CR] Set value of Gamma
CF_WBAL-R_%1 [CR] CF_WBAL-G_%1 [CR] CF_WBAL-B_%1 [CR] CF_COLTEMP_%1 [CR] CF_OFFSET-R_%1 [CR] CF_OFFSET-G_%1 [CR] CF_OFFSET-B_%1 [CR] CF_NZRED_%1 [CR]
CF_PROGV_%1 [CR] CF_IMAGE_%1 [CR] CF_IMAGEADJ_%1 [CR]
Set Red value of White Balance Set Green value of White Balance Set Blue value of White Balance Set level of Color Temperature Set Red value of Offset Set Green value of Offset Set Blue value of Offset Set ON/OFF of Noise reduction
Set mode of Progressive scan
Set Image mode
Set Store/Reset of values in Image Adjustment
5.2 PC Adjust Control Command Table
Execute command Item
CF_FSYNC_%1 [CR] Set value of Fine Sync CF_TDOTS_%1 [CR] Set value of Total Dots CF_CLPPHASE_%1 [CR] Set value of Clamp Phase CF_H-POS_%1 [CR] Set value of Horizontal Position CF_V-POS_%1 [CR] Set value of Vertical Posit ion CF_DDOTS_%1 [CR] Set value of Display Dots CF_DLINE_%1 [CR] Set value of Display Line CF_SETPCADJ_%1 [CR] Apply values set in PC Adjust menu to screen image CF_ORGMODE_%1 [CR] Specify the original signal for PC mode
CF_PCSTORE_%1 [CR]
CF_PCMODEFREE_%1 [CR]
5.3 Input Control Command Table
Execute command Item
CF_INPUT_%1 [CR] CF_SOURCE_%1 [CR] CF_INPUT1_%1 [CR] CF_INPUT2_%1 [CR] CF_INPUT3_%1 [CR] CF_INPUT4_%1 [CR] CF_SYSTEM_%1 [CR]
Store current setting values in PC Adjust menu to Mode %1 Delete the values registered in Mode %1 and return it to Free status.
Select Input Select Source of selected Input Select Input1 and also set input source to %1 Select Input2 and also set input source to %1 Select Input3 and also set input source to %1 Select Input4 and also set input source to %1 Select System of currently selected Input
11/79
PLC-XM100/XM100L/XM150/XM150L Expand Serial Command Functional Specifications
5.4 Screen Control Command Table
Execute command Item
CF_SCREEN_%1 [CR] CF_DZCENT _%1 [CR] CF_KEYSTONE _%1 [CR] CF_KYSTNMODE _%1 [CR] CF_CORNER-UL_%1[CR] CF_CORNER-UR_%1[CR] CF_CORNER-DL_%1[CR] CF_CORNER-DR_%1[CR] CF_CORNERTESTPAT_%1[CR] CF_CEIL_%1 [CR] CF_REAR_%1 [CR] CF_VSCALE_%1[CR] CF_VPOS_%1[CR] CF_HSCALE_%1[CR] CF_HPOS_%1[CR]
Select Screen size Cancel Digital Zoom mode Set Keystone correction Set Keystone store mode Correct top-left corner Correct top-right corner Correct bottom-left corner Correct bottom-right corner Select test pattern for Corner correction. Set ON/OFF of Ceiling Set ON/OFF of Rear Set V Scale Set V Position Set H Scale Set H Position
5.5 Lamp Command Table
Execute command Item
CF_LAMPMODE_%1 [CR] CF_LAMPLIFECONTRL_%1 [CR]
Select Lamp mode Select Lamp life mode
5.6 Sound Command Table
Execute command Item
CF_VOLUME_%1 [CR] CF_MUTE_%1 [CR] CF_BLTINSP_%1 [CR]
5.7 Setting Command Table
Execute command Item
CF_LANG_%1 [CR] CF_MENUPOSITION_%1 [CR] CF_INPUTBUTTON_%1[CR] CF_DISP_%1 [CR] CF_BACKGND_%1[CR] CF_LOGO_%1 [CR] CF_FILH_%1[CR]
CF_FILTIMER_%1[CR]
CF_FILCTL_%1[CR] CF_FILSCRL_%1[CR] CF_FANSPEED_%1 [CR] CF_SIMPLEMODE_%1 [CR] CF_RCODE_%1 [CR]
CF_RSENS_%1 [CR]
CF_P-MANE_%1 [CR] CF_P-MANETIME_%1 [CR] CF_STANDBYMODE_%1 [CR] CF_ON-STA_%1 [CR] CF_POINTER_%1[CR] CF_PTIMEMODE_%1[CR] CF_PTIMER_%1[CR] CF_PTIME_%1[CR] CF_KEYDIS_%1 [CR]
Set value of Volume Set ON/OFF of Sound Mute Set ON/OFF of Built-in speaker
Select language for OSD Select the position of the On-Screen Menu. Set up Input search function Set ON/OFF of On Screen Display Select screen for no signal Set PIN code and mode for Logo Reset Filter used time Set time to display Filter cleaning / replacement warning
on screen Execute operation of scroll of filter Reset Filter scroll counter Set level of Fan Speed Set Simple mode function Select Remote Control Code Select location of infrared remote receiver of remote control Set Power Management function Set time of Power Management Set Standby mode Set ON/OFF of Power ON Start Set Pointer function Set count up / count down in P-timer function Set the status of P-timer Set the time for count down mode in P-timer function Prohibit RC/KEY control
12/79
PLC-XM100/XM100L/XM150/XM150L Expand Serial Command Functional Specifications
CF_PJPINCODE_%1[CR] CF_SHUTRCPROT_%1[CR]
CF_SHUTKEYPROT_%1[CR]
CF_SHUTH_%1[CR] CF_DELAYCTRL_%1[CR] CF_TESTPAT_%1[CR] CF_FDEFAULT_%1 [CR]
5.8 Other Command Table
Execute command Item
CF_KEYEMU_%1 [CR] CF_MENU_%1 [CR] CF_POWER_%1 [CR] CF_FREEZE_%1 [CR] CF_VMUTE_%1 [CR]
Enter PJ PIN code to cancel PJ lock Set valid / invalid of RC use on Shutter control function Set valid / invalid use of key on the top panel on Shutter
control function Set time of operating shutter management function Set Video delay control function Set Test pattern display function Reset to Factory Default settings
The same operation as Control Key Set ON/OFF of Menu Set ON/OFF of Power Set ON/OFF of Freeze Set ON/OFF of Video Mute
13/79
PLC-XM100/XM100L/XM150/XM150L Expand Serial Command Functional Specifications
6． Status Read Command Table
6.1 Image Status Read Command Table
Status Read command Item
CR_BRIGHT [CR] CR_CONT [CR] CR_COLOR [CR] CR_TINT [CR] CR_SHARP [CR] CR_GAMMA [CR] CR_WBAL-R [CR] CR_WBAL-G [CR] CR_WBAL-B [CR] CR_COLTEMP [CR] CR_OFFSET-R[CR] CR_OFFSET-G[CR] CR_OFFSET-B[CR] CR_NZRED [CR] CR_PROGV [CR] CR_IMAGE [CR] CR_IMGGMD [CR]
Get value of Brightness Get value of Contrast Get value of Color Get value of Tint Get value of Sharpness Get value of Gamma Get Red value of White Balance Get Green value of White Balance Get Blue value of White Balance Get value of Color temperature Get Offset Red Get Offset Green Get Offset Blue Get setting status of Noise reduction Get setting status of Progressive scan Get Selected Image status Get setting value of Image Gamma
6.2 PC Adjust Status Read Command Table
Status Read command Item
CR_FSYNC [CR] CR_TDOTS [CR] CR_CLPPHASE [CR] CR_H-POS [CR] CR_V-POS [CR] CR_DDOTS [CR] CR_DLINE [CR] CR_ORGMODE [CR] Get the original signal for PC-Adjusted mode
CR_PCSTORE [CR] CR_SETPCADJ [CR]
Get setting value of Fine Sync Get setting value of Total Dots Get setting value of Clamp phase Get setting value of Horizontal Position Get setting value of Vertical Position Get setting value of Display Dots Get setting value of Display Line
Get status Free/ Stored for PC Adj. mode 1-10 Get currently displayed PC signal in system
6.3 Video Status Read Command Table
Status Read command Item
CR_SERSYS [CR]
Get currently selected signal. In Auto mode, it returns a result by Auto detection.
6.4 Input Status Read Command Table
Status Read command Item
CR_INPUT [CR] CR_SOURCE [CR] CR_SRCINP1 [CR] CR_SRCINP2 [CR] CR_SRCINP3 [CR] CR_SRCINP4 [CR] CR_SYSTEM [CR] CR_SYSLIST [CR] CR_MODELIST [CR] CR_HMSLOT [CR] CR_NMSLOT1 [CR] CR_NMSLOT2[CR] CR_NMSLOT3[CR]
CR_NMSLOT4[CR]
Get selected Input Get selected Source Get selected source for Input 1 Get selected source for Input 2 Get selected source for Input 3 Get selected source for Input 4 Get selected system in current Input mode Get possible system list Get possible mode list Get total number of Inputs Get terminal information of Input1. Get terminal information of Input2. Get terminal information of Input3
Get terminal information of Input4.
14/79
PLC-XM100/XM100L/XM150/XM150L Expand Serial Command Functional Specifications
CR_IDSLOT1[CR] CR_IDSLOT2[CR] CR_IDSLOT3[CR] CR_IDSLOT4[CR]
Get ID information of Input1
Get ID information of Input2
Get ID information of Input3
Get ID information of Input4
6.5 Screen Status Read Command Table
Status Read command Item
CR_SCREEN [CR] CR_VSCALE[CR] CR_VPOS[CR] CR_HSCALE[CR] CR_HPOS[CR] CR_KYSTNMODE[CR] CR_CORNERTESTPAT [CR] Get setting of test pattern for Corner correction. CR_CEIL [CR] CR_REAR [CR]
6.6 Lamp Status Read Command Table
Status Read command Item
CR_LAMPREPL [CR] CR_LAMPH [CR] CR_LAMPCORRESPH [CR] CR_LAMPMODE [CR] CR_LAMPSTS [CR] CR_PROJH [CR] CR_HMLAMP [CR] CR_LAMPLIFECONTRL [CR]
Get selected screen size Get setting status of V Scale Get setting status of V Position Get setting status of H Scale Get setting status of H Position Get selected Keystone store mode
Get setting status of Ceiling Get setting status of Rear
Get information of Lamp replacement time Get information of actual Lamp running time Get lamp running time multiplied by a coefficient Get selected Lamp mode Get status of the Lamp Get total running time of projector Get the total number of lamps Get selected mode in Lamp life control function
6.7 Sound Status Read Command Table
Status Read command Item
CR_VOLUME [CR] CR_MUTE [CR] CR_BLTINSP [CR]
6.8 Setting Status Read Command Table
Status Read command Item
CR_LANG [CR] CR_INPUTBUTTON [CR] CR_DISP [CR] CR_BACKGND [CR] CR_LOGO [CR] CR_LOGOLOCK[CR] CR_FILREMAIN[CR] CR_FILH[CR]
CR_FILTIMER[CR]
CR_FILCOND[CR] CR_FILREPL[CR] CR_FANSPEED [CR] CR_SIMPLEMODE [CR] CR_RCODE [CR]
CR_RSENS [CR]
CR_RTYPE [CR] CR_P-MANE [CR]
Get selected language Get setting status of Input button function Get setting status of Display Get setting status of Screen for no signal Get setting status of Logo Get setting status of Logo Lock Get remaining number of usable Filter scroll Get Filter used time Get time to display Filter cleaning / replacement warning on
screen Get status of filter clog Get status of Filter cleaning / replacement time Get selected Fan Control Speed Get selected mode in Simple mode function Get selected Remote Control code Get selected location of infrared remote receiver of remote control Get supported Remote Control type (IR/RF) Get Power management setting status
Get value of Volume Get setting status of Sound Mute Get setting status of Built-in speaker
15/79
PLC-XM100/XM100L/XM150/XM150L Expand Serial Command Functional Specifications
de in operation.
CR_P-MANETIME [CR] CR_STANDBYMODE [CR] CR_ON-STA [CR] CR_POINTER[CR] CR_PTIMEMODE[CR] CR_PTIMER[CR] CR_PTIME[CR] CR_KEYDIS [CR] CR_SECURITY [CR] CR_PJLOCKNOW [CR] CR_PJLOCKMENU [CR] CR_SHUTRCPROT[CR] CR_SHUTKEYPROT[CR] CR_SHUTH[CR] CR_DELAYCTRL[CR] CR_TESTPAT[CR]
Get setting time for Power Management Get selected mode of Standby function Get ON Start setting status Get setting status of Pointer Get setting mode of P-timer Get status of P-timer Get setting time for count down mode in P-timer Get RC/KEY prohibited status Get setting status of Security Get setting status of current PJ Lock Get PJ Lock setting status on the menu Get remote controller disability status of the shutter Get Key controller disability state of the shutter Get time setting to begin the shutter management Get selected mode of Video delay control Get setting status of Test pattern
6.9 Other Status Read Command Table
Status Read command Item
CR_STATUS [CR] CR_SIGNAL [CR] CR_VMUTE [CR] CR_FREEZE [CR]
CR_TEMPFAIL [CR]
CR_TEMP [CR] CR_SHUTCOND [CR] CR_SERIALNO [CR]
Get operating status of Projector Get status of signal existence Get setting status of No show Get setting status of Freeze Get temperature when sensors approach abnormal
temperature Get current temperature Get setting status of Shutter Get value of SERIAL NO.
7． Error Code Table
Error Code Contents
000 Normal reception (This is “Not” error)
101 The function is not available in the selected Mode
102 Selected value is out of range (Not reflected)
103
201
301
402
Note) These error codes are applied to Expand Command, not to Basic Command
-When the received data cannot be decoded
?
-Parameter designation error (wrong digit number, including invalid value, etc.)
Command mismatched to Hardware (the command is for Optional function which is not implemented)
Incremented or decremented value or values are beyond upper or lower limits.
Not executable due to screen capturing in process. Prompting reissue of the command after a while.
Not executable due to PIN co Prompting reissue of the command after a while.
16/79
PLC-XM100/XM100L/XM150/XM150L Expand Serial Command Functional Specifications
8． Functional Execution Command
8.1 Format
1) PC issues commands in format as below:
Pattern1: “CF_ COMMAND” [CR]
Pattern2: “CF_ COMMAND _” %1 [CR]
CF_: Header
COMMAND: String
%1: Parameter (String)
_: Space (To separate COMMAND and Parameter)
2) The projector decodes the received command and when it is ready to receive the next
command, it returns the response.
“000” [CR]:（0x06,0x0D）When receiving Functional Execution Command
“nnn” [CR]: Except “000”, when it is unable to execute command for any specific reason.
See Error Code Table for details
3) When the received data cannot be decoded, the projector returns ”?” [CR]
8.2 Transfer Example
When setting projector’s total dots to 1344 by Expand Serial command
PC → PJ: “CF_TDOTS_1344” [CR]
PC → PJ: “000” [CR] - - - - - - - - - - Acceptable
8.3 Operation Requirements
1. Functional Execution Command is limited when the projector status is as below.
However, Status Read Command is still effective under following conditions.
Projector Status Available Functional Execution Command
Standby Mode
Countdown in process
Cooling Down in process N/A Cooling Down due to
Abnormal Temperature Abnormal Temperature N/A Power Failure
(60 seconds after Power failure occurred)
Abnormal Filter N/A
Power-Save Cooling Down in process N/A
Cooling Down in process due to Shutter management
Power Save in process
Note) When projector receives another command in the above status, it returns error code which
C00: Power ON CF POWER ON C00: Power ON CF POWER ON (Terminates Count Down)
N/A
N/A
N/A
C00: Power ON C01: Power OFF CF POWER ON CF POWER OFF
shows the status.
2. Functional Execution Commands are invalid when projector is in standby under Eco mode
17/79
PLC-XM100/XM100L/XM150/XM150L Expand Serial Command Functional Specifications
8.4 Image Command
8.4.1 CF_ BRIGHT Command
Command “CF_BRIGHT_%1” [CR]
%1
Details
Response
“000-063”--------------- Directly specify setting value of Brightness “UP”--------------------- Increment setting value of Brightness by 1 “DN”--------------------- Decrement setting value of Brightness by 1
Set user controlled value of Brightness (Available only in the normal Power ON status) The value set by this command will not be stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Acceptable “000” [CR]
Unacceptable “Error Code” [CR]
8.4.2 CF_CONT Command
Command “CF_CONT_%1” [CR]
%1
Details
Response
“000-063”--------------- Directly specify setting value of Contrast “UP”--------------------- Increment setting value of Contrast by 1 “DN”--------------------- Decrement setting value of Contrast by 1
Set user controlled value of Contrast (Available only in the normal Power ON status) The value set by this command will not be stored in the projector. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Acceptable “000” [CR]
Unacceptable “Error Code” [CR]
8.4.3 CF_COLOR Command
Command “CF_COLOR_%1” [CR]
%1
Details
Response
“000-063”--------------- Directly specify setting value of Color “UP”--------------------- Increment setting value of Color by 1 “DN”--------------------- Decrement setting value of Color by 1
Set user controlled value of Color (Available only in the normal Power ON status) The value set by this command will not be stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Acceptable “000” [CR]
Unacceptable “Error Code” [CR]
8.4.4 CF_TINT Command
Command “CF_TINT_%1” [CR]
%1
Details
Response
“000-063”--------------- Directly specify setting value of Tint “UP”--------------------- Increment setting value of Tint by 1 “DN”--------------------- Decrement setting value of Tint by 1
Set Tint value (Available only in the normal Power ON status) The value set by this command will not be saved to the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Acceptable “000” [CR]
Unacceptable “Error Code” [CR]
18/79
PLC-XM100/XM100L/XM150/XM150L Expand Serial Command Functional Specifications
8.4.5 CF_SHARP Command
Command “CF_SHARP_%1” [CR]
%1
Details
Response
“000-031”--------------- Directly specify setting value of Sharpness “UP”--------------------- Increment setting value of Sharpness by 1 “DN”--------------------- Decrement setting value of Sharpness by 1
Set user controlled value of Sharpness (Available only in the normal Power ON status) The value set by this command will not be stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Acceptable “000” [CR]
Unacceptable “Error Code” [CR]
8.4.6 CF_GAMMA Command
Command “CF_GAMMA_%1” [CR]
%1
Details
Response
“000-015”---------------- Directly specify setting value of Gamma “UP”---------------------- Increm ent setting value of Gamma by 1 “DN”---------------------- Decrement setting value of Gamma by 1
Set user controlled value of Gamma (Available only in the normal Power ON status) The value set by this command will not be stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Acceptable “000” [CR]
Unacceptable “Error Code” [CR]
8.4.7 CF_WBAL- Command
Command “CF_WBAL-%1_%2” [CR]
%1
%2
Details
Response
“R” --------- RED “G” --------- GREEN “B” --------- BLUE
“000-063”------ Directly specify value of Color selected in %1 of White Balance. “UP”-------- Increment setting value of Color specified in %1 of White Balance by 1 “DN”------- Decrement setting value of Color specified in %1 of White Balance by 1
Set value of Color specified in %1 of W hite Balance (Available only in the normal Power ON status) The value set by this command will not be stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Acceptable “000” [CR]
Unacceptable “Error Code”[CR]
19/79
PLC-XM100/XM100L/XM150/XM150L Expand Serial Command Functional Specifications
8.4.8 CF_COLTEMP Command
Command “CF_COLTEMP_%1” [CR]
“000” ------------------------------ Xlow
%1
Details
Response
“001”------------------------------- Low “002”------------------------------- Mid “003”------------------------------- High
Set Color Temperature The value set by this command will not be stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Acceptable “000” [CR]
Unacceptable “Error Code” [CR]
8.4.9 CF_OFFSET- Command
Command “CF_OFFSET-%1_%2” [CR]
%1
%2
Details
Response
“R” --------- RED “G” --------- GREEN “B” --------- BLUE
“000-063”------ Directly specify value of Color selected in %1 of Offset. “UP”------------ Increment setting value of Color specified in %1 of Offset by 1 “DN”------------ Decrement setting value of Color specified in %1 of Offset by 1
Set value of Color specified in %1 of Offset (Available only in the normal Power ON status) The value set by this command will not be stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Acceptable “000” [CR]
Unacceptable “Error Code”[CR]
8.4.10 CF_NZRED Command
Command “CF_NZRED_%1” [CR]
“OFF” ---------------- Cancel Noise Reduction
%1
Details
Response
“ON” ------------------- Set Noise Reduction “UP” ------------------ Toggle between ON and OFF. (On→OFF→On→...) “DN” ------------------ Toggle between ON and OFF. (On→OFF→On→...) *”UP” and “DN” are exactly same operation.
Set Noise Reduction level (Available only in the normal Power ON status) The value set by this command will not be stored in the proj ector’s memory Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It returns to the original setting in Suspend mode as well.)
Acceptable “000” [CR]
Unacceptable “Error Code” [CR]
20/79
PLC-XM100/XM100L/XM150/XM150L Expand Serial Command Functional Specifications
8.4.11 CF_PROGV Command
Command “CF_PROGV_%1” [CR]
“ON” ----------------- Set Progressive scan to On.
%1
Details
Response
“FILM” --------------- Set Progressive scan to Film. “OFF” ---------------- Set Progressive scan to OFF. “UP” ------------------ Switch setting forward direction (OFF→ON→FILM→OFF) “DN” ------------------ Switch setting backward direction (OFF→FILM→ON→OFF)
Set Progressive scan mode. (Available only in the normal Power ON status) The value set by this command will not be stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Acceptable “000” [CR]
Unacceptable “Error Code” [CR]
8.4.12 CF_IMAGE Command
Command “CF_IMAGE_%1” [CR]
“STAND” ------ Standard(Image adjust value is set to factory default for Still Image) “REAL------------------ Real (Fixed value to display graphic image with natural tone) “CINEMA”------------- Cinema (Fixed value to focus on tone reproduction for movie) “CUSTOM1” ------------- Image1 （the value adjusted and stored by user）
“CUSTOM2” ------------- Image2 （the value adjusted and stored by user） “CUSTOM3” ------------- Image3 （the value adjusted and stored by user）
%1
Details
Response
“CUSTOM4” ------------- Image4 （the value adjusted and stored by user） “CUSTOM5” ------------- Image5 （the value adjusted and stored by user） “CUSTOM6” ------------- Image6 （the value adjusted and stored by user） “CUSTOM7” ------------- Image7 （the value adjusted and stored by user） “CUSTOM8” ------------- Image8 （the value adjusted and stored by user） “CUSTOM9” ------------- Image9 （the value adjusted and stored by user） “CUSTOM10” ----------- Image10 （the value adjusted and stored by user）
Select Image Mode (Available only in the normal Power ON status) Parameter “CUSTOM1” to “CUSTOM10” corresponds to “Image1” to “Image10” displayed in projector OSD menu on selecting Image. The value set by this command is stored in EEPROM so that the setting can remain effective even after the power is turned to ALL OFF status.
Acceptable “000” [CR]
Unacceptable “Error Code” [CR]
21/79
PLC-XM100/XM100L/XM150/XM150L Expand Serial Command Functional Specifications
8.4.13 CF_IMAGEADJ Command
Command “CF_IMAGEADJ_%1”[CR]
“RST”------ Reset adjusted value for the Image “STR1”---- Store current adjusted value to Image 1 “STR2”---- Store current adjusted value to Image 2 “STR3”---- Store current adjusted value to Image 3
%1
Details
Response
“STR4”---- Store current adjusted value to Image 4 “STR5”---- Store current adjusted value to Image 5 “STR6”---- Store current adjusted value to Image 6 “STR7”---- Store current adjusted value to Image 7 “STR8”---- Store current adjusted value to Image 8 “STR9”---- Store current adjusted value to Image 9 “STR10”---- Store current adjusted value to Image 10
Reset or Store adjusted value for Image. (Available only in the normal Power ON status) “STR1”-”STR10” corresponds to “Image1”-”Image10” displayed in projector OSD menu on selecting “Store” for adjusted value of Image. The setting value set in “Image1” to “Image10” is stored and can be retrieved when turning on the projector again after the power is turned to ALL OFF status.
Acceptable “000” [CR]
Unacceptable “Error Code” [CR]
22/79
PLC-XM100/XM100L/XM150/XM150L Expand Serial Command Functional Specifications
8.5 PC Adjust Control Command
8.5.1 CF_FSYNC Command
Command “CF_FSYNC_%1” [CR]
%1
Details
Response
“0000-0031” ----------------- Directly specify setting value of Fine Sync “UP” --------------------------- Increment setting value of Fine Sync by 1 “DN” --------------------------- Decrement setting value of Fine Sync by 1
Set value of Fine Sync in PC signal (Available only in the normal Power ON status) The value set by this command will not be stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting.
Acceptable “000” [CR]
Unacceptable
“101” [CR] --- When input is Video signal
--- When input is no signal
8.5.2 CF_TDOTS Command
Command “CF_TDOTS_%1” [CR]
“mmmm - nnnn” --------------- Directly specify setting value of Total Dots
%1
Details
Response
“mmmm” indicates m inimum value, which is current (Display area H + Position H)
“nnnn” indicates maximum value, which is less than 140 MHz in D ot Clocks
“UP” ------------------------- Increment setting value of Total Dots by 1 “DN” ------------------------- Decrement setting value of Total Dots by 1
Set value of Total Dots in PC signal (Available only in the normal Power ON status) The value set by this command will not be stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting.
Acceptable “000” [CR]
Unacceptable
value
“101” [CR] --- When input is Video signal
--- When input is no signal
8.5.3 CF_CLPPHASE Command
Command “CF_CLPPHASE_%1” [CR]
%1
Details
Response
“0000-0255” ----------- Directly specify setting value of Clamp Phase “UP” --------------------- Increment setting value of Clamp Phase by 1 “DN” --------------------- Decrement setting value of Clamp Phase by 1
Set value of Clamp Phase (Available only in the normal Power ON status) The value set by this command will not be stored in the projector. Therefore, when
the power is turned to ALL OFF, the value returns to the original setting.
Acceptable “000” [CR]
Unacceptable
“101” [CR] --- When input is Video signal
--- When input is no signal
23/79
PLC-XM100/XM100L/XM150/XM150L Expand Serial Command Functional Specifications
8.5.4 CF_H-POS Command
Command “CF_H-POS_%1” [CR]
“0000-nnnn” -------- Directly specify setting value of Horizontal Position
%1
Details
Response
“nnnn” indicates maximum value, which is current value of (Total dots - Display area H)
“UP” ------------------- Increment setting value of Horizontal Position by 1 “DN” ------------------ Decrement setting value of Horizontal Position by 1
Set value of Horizontal Position in PC signal (Available only in the normal Power ON status) The value set by this command will not be stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting.
Acceptable “000” [CR]
Unacceptable
“101” [CR] --- When input is Video signal
--- When input is no signal
8.5.5 CF_V-POS Command
Command “CF_V-POS_%1” [CR]
“0000-nnnn” ------------ Directly specify setting value of Vertical Position
%1
Details
Response
“nnnn” indicates maximum value, which is current (Total Line – Display Area V) value
“UP” --------------------- Increment setting value of Vertical Position by 1 “DN” --------------------- Decrement setting value of Vertical Position by 1
Set Vertical Position value (Available only in the normal Power ON status) The value set by this command will not be stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting.
Acceptable “000” [CR]
Unacceptable
“101” [CR] ---- When input is Video signal
--- When input is no signal
8.5.6 CF_DDOTS Command
Command “CF_DDOTS_%1” [CR]
“0100-nnnn” -------------- Directly specify setting value of Display Dots
%1
Details
Response
“nnnn” indicates maximum value, which is current value of (Total Dots - Position H).
In this projector, t he value should be “ even number” and if “odd number” is specified, it adds 1 to make the value even number.
“UP” ------------------------ Increment setting value of Display Dots by 2 “DN” ------------------------ Decrement setting value of Display Dots by 2
Set setting value of Display Dots in PC signal (Available only in the normal Power ON status) The value set by this command will not be stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting.
Acceptable “000” [CR]
Unacceptable
“101” [CR] --- When input is Video signal
--- When input is no signal
24/79
Loading...
+ 55 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use