Sanyo LMU-TK12AS2, LMU-TK12AS2TC, LMU-TK12AS2TR Instruction Manual

Download

Industrial LCD Monitor

LMU-TK12AS2 LMU-TK12AS2TC

(With Capacitive Touch Screen)

LMU-TK12AS2TR

(With Resistive Touch Screen)

User's Guide

PrecautionsTable of contents

Precautions....................................................................................... 2

1. Before First Use

Names and Functions ................................................................. 3-6

Check Accessories......................................................................... 7

Installation................................................................................. 7-10

Outer Dimension...................................................................... 11,12

2. LCD Monitor Instructions

Adjusting the Screen .................................................................... 13

Adjustment Procedure.................................................................. 14

Adjustment Procedure (Menu Screen).................................. 15 - 17

Adjustment Procedure (Sub-menu Screen) .......................... 18 - 23

Additional Functions............................................................... 23, 24

3. Maintenance................................................................................ 25

4. Troubleshooting

Fault Finding................................................................................. 26

Screen Display ............................................................................. 27

5. Specifications

Table of Preset Data..................................................................... 28

Monitor Specifications ............................................................ 29, 30

Placement precautions

• Avoid placing the unit in humid or dusty places, or where it will be exposed to excessive heat (direct sunlight, heaters, etc.)

• Do not step on or set anything on the AC power cord. DAMAGE TO THE AC POWER CORD IS A SAFETY RISK AND CAN CAUSE A FIRE.

• For use with specified AC adapter (GI40-US1225) only.

• Install the unit only on a stable and smooth surface.

• Do not connect the unit to the same AC as outlet with appliances that generate large amounts of interference (such as heaters with thermostats, appliances with motors, etc.). It is best to use a completely separate electrical outlet.

• Keep the unit away from water. If water accidentally enters the unit, unplug the AC power cord immediately. DO NOT PLUG IN THE UNIT AGAIN.

Handling precautions

• Avoid bending, kinking or damaging the AC power cord.

• Never insert or remove the power cord with wet hands. Also, be sure to hold cord by the plug when removing it from the outlet.

• Do not remove any parts that are held in place with screws. (The unit does not contain any user-serviceable items.)

• Maintain standard room temperature (5˚C to 35˚C, or 41˚F to 95˚F) during use. Do not subject the unit to shock or vibration. Do not move the unit while it is in use.

• A rapid increase in room temperature in cool weather can cause condensation to form inside the unit. If this occurs, wait at least 15 minutes after turning the unit on before attempting to operate it.

Microsoft and Windows are registered trademarks of Microsoft Corporation in the U.S.A. and other countries.

European Norm Compatibility / CE

This machine is provided with the CE-mark and therewith corresponding to the norms that are valid for its operation at present. Thus the effective guidelines on the electromagnetic compatibility 89/336/EWG and safety regulations according to low voltage guideline 73/23/EWG and 93/68/EWG are guaranteed. Mutual disturbances with other electronic appliances are normally excluded, if those also are in accordance with valid norms. Sporadically disturbances cannot, however, be excluded. The product is in conformity with the directives of the valid European guideline.

Rear View

Names and Functions

Before First Use

Power Indicator

Light either green or orange when the power is turned on(See page 24)

Display Screen

Front View

LMU-TK12AS2

DC IN jack

（  ）

Power Switch

（  ）

Brightness Control（  ）

Used to adjust the brightness of the display.

RGB Connector

（）

OSD Control Connector

Before First Use

Names and Functions

DC IN jack

（  ）

Power Switch

（  ）

Brightness Control（  ）

Used to adjust the brightness of the display.

RGB Connector

（）

OSD Control Connector

Serial port Connector

（）

Power Indicator

Light either green or orange when the power is turned on(See page 24)

Touch Screen

Front View

LMU-TK12AS2TC, LMU-TK12AS2TR

Rear View

7 8

Before First Use

Check Accessories

Check that the main unit and all accessories are present.

¡¡

AC adapter (

¡¡

AC power cord (

¡¡

RGB Cable (

¡¡

External OSD control box (

¡¡

User's Guide (

for LMU-TK12AS2TC

LMU-TK12AS2TR

¡¡

Serial Cable (

¡¡

Touch Ware CD-ROM (

Installation

Setting Up the Stand

Used as a desktop monitor by turnishing a stand (included).

1. Remove the labels from the back of the monitor.

2. Place the monitor on the stand's hooks.

3. Fix firmly using the two screw supplied.

You can adjust the angle of the monitor to get the best position for viewing.

Befor First Use

Installation

DC IN jack

DC plug

Power plug

AC adapter

RGB Connector

RGB cable

OSD Control Connector

OSD Control BOX

Connect to the computer's connector

Connecting the Cables and Power Supply

Before doing anything, make sure the power switches on the monitor and the computer it is going to be connected to are turned off.

Plug the cables into the connector on the monitor securely and fix them in place with the two screws.

Plug the other end of the cables into the connector on the computer.

Plug the DC plug on the AC adapter into the DC IN jack on the monitor.

Plug the AC power cord into the AC adapter.

Plug the power plug into an outlet.

Plug the external OSD control box if necessary.

• Do not plug the external OSD control box into the computer's USB port, as this may cause malfunction of the computer.

Caution

DC IN jack

DC plug

Power plug

AC adapter

RGB Connector

RGB cable

Serial cable

OSD control Connector

OSD control BOX

Serial Port Connector

Connect to the computer's connectors

LMU-TK12AS2

LMU-TK12AS2TC LMU-TK12AS2TR

Before First Use

Outer Dimension

note

LMU-TK12AS2

note

LMU-TK12AS2TC / LMU-TK12AS2TR

Note : Fixing holes (VESA standard)

Maximum depth of a screw: 3.5 mm

Note : Fixing holes (VESA standard)

Maximum depth of a screw: 3.5 mm

LCD Monitor Instructions

13 14

Adjusting the Screen Adjustment Procedure

A LCD Monitor decodes the signal from a computer automatically, and displays the image on a screen in accordance with the preset mode. Unless a display mode has been preset, the image is displayed in the similar mode to the one from computer. In this case, the adjustment for a LCD moitor must be done in accordance with a computer connected with. A LCD displays the information to be adjusted for screen on OSD (On Screen Display) menu. The OSD is the great tool, which makes it possible to adjust the screen easily and smoothly.

Please make touch screen adjustments after adjusting the screen settings. Consult Touch Ware CD-ROM (included) for details.

Buttons and Functions

[MENU] Button To display the Menu Screen ON/OFF [ENTER] Button To choose the item adjusted, and store the data

adjusted

[ ] [ ] Button To move the cursor between the items adjusted and

change the adjustment data

Menu Screen (Refer to Page 14 - 17)

Adjustment ltems

AUTO ADJUST

‥ ‥‥‥ ‥ ‥ ‥

Adjust the screen mode automatically

HOR. SIZE

‥ ‥‥‥ ‥ ‥ ‥ ‥ ‥

Adjust the width of screen Horizontally

FOCUS

‥ ‥‥‥ ‥ ‥ ‥ ‥ ‥ ‥‥

Adjust the focus of screen

HOR. POSITION

‥ ‥‥‥ ‥ ‥ ‥

Adjust the Horizontal position

VERT. POSITION

‥ ‥‥‥ ‥ ‥ ‥

Adjust the Vertical position

Sub - menu Screen (Refer to Page 18 - 22)

COLOR

‥ ‥‥‥ ‥ ‥ ‥ ‥ ‥ ‥‥

Adjust the level of color (RED / GREEN / BLUE)

RECALL

‥ ‥‥‥ ‥ ‥ ‥ ‥ ‥ ‥

Set the data back to the original data programmed by manufacturer

VIDEO MODE

‥ ‥‥‥ ‥ ‥ ‥ ‥

Display the input signal data

BLACK LEVEL

‥ ‥‥‥ ‥ ‥ ‥ ‥

Adjust the black level

LANGUAGE

‥ ‥‥‥ ‥ ‥ ‥ ‥ ‥

To change the language used on OSD (On Screen Display)

Display the Windows or other screen.

After a Computer is connected with a LCD Monitor, activate a Computer and then shows a bright screen on a LCD Monitor. It might be possible not to adjust the screen correctly for a dark screen.

Enter the Adjustment Mode.

Pressing the [MENU] button, the following menu is display.

For DOS mode, run an application that shows the edges of the screen (edit, etc.) before beginning adjustment.

Before Adjustment

Move the cursor on the menu screen with the [ ] button and/or [ ] button to select the item to be adjusted. Upon pressing the [ENTER] button, the adjustment screen for the selected item is displayed.

･Adjust the screen automatically ･Adjust the size of screen Horizontally ･Adjust the focus of screen ･Adjust the Horizontal position ･Adjust the Vertical position

AUTO ADJUST HOR.SIZE FOCUS HOR.POSITION VERT.POSITION

The signal timing for a computer which this LCD monitor supports is listed in "Table of Preset Data" on Page 28, the recommended value of Vertical Frequency for this model is 60Hz. (Unlike CRT Monitors, the display becomes stable when Vertical Frequency is low.) It is recommend to set Vertical Frequency of a computer connected at 60Hz by "refresh rate setting". before starting adjustment procedure.

1615

Adjustment Procedure (Menu Screen)

LCD Monitor Instructions

Adjusted by the following steps :

1. Select "AUTO ADJUST" on the Menu screen

2.Press the [ENTER] button to

start the Auto Adjustment

2.Press the [MENU] button to

cancel this procedure, then be back to the Menu screen automatically.

3.Automatic Adjustment

successfully completed.

To save the data set in Auto Adjustment and disappear the Menu screen

By pressing the [MENU] button, step back to the Menu screen.

3.Automatic Adjustment

unsuccessfully completed.

ENTER EXECUTE MENU CANCEL

AUTO ADJUST

a a

FAILED

RETRY OR SEE USER'S GUIDE

AUTO ADJUST

COMPLETE

Automatic Adjustment Manual Adjustment

In case the result adjusted by Auto adjust sequence is not sufficient enough, adjust the screen by manually.

Adjusting the Horizontal Width of a display

1. Select "HOR. SIZE" (Horizontal Size) on the Menu screen.

2. Use the [ ] and [ ] buttons to perform adjustment.

By pressing the [ ] button, the Horizontal Width becomes Wider. By pressing the [ ] button, the Horizontal Width becomes narrower.

3. Press the [ENTER] button, to save the preset data and be back to

the Menu screen.

Press the [MENU] button, to cancel this procedure and be back to the Menu screen. In this case, the preset data is not saved.

HOR.SIZE NARROW WIDE

(Ex.)

Adjust the Focus

1. Select "FOCUS" on the Menu screen.

2. By using [ ] and/or [ ] button, adjust the screen to be able to

display the small characters clearly.

3. Press the [ENTER] button, to save the preset data and be back to

the Menu screen.

Press the [MENU] button, to cancel this procedure and be back to the Menu screen. In this case, the preset data is not saved.

FOCUS

------------------------------ [ 0]

(Ex.)

Adjustment Procedure (Sub-menu Screen)

LCD Monitor Instructions

Adjustment Procedure (Menu Screen)

1. Select "HOR. POSITION" on the Menu screen.

2. Use the [ ] and [ ] buttons to perform adjustment.

Press the [ ] button to shift the screen to the left. Press the [ ] button to shift the screen to the right.

3. Press the [ENTER] button, to save the preset data and be back to

the Menu screen.

Press the [MENU] button, to cancel this procedure and be back to the Menu screen. In this case, the preset data is not saved.

HOR. POSITION LEFT RIGHT

Adjust the Vertical Position

1. Select "VERT. POSITION" on the Menu screen.

Disappearance of Menu Screen

By pressing [MENU] button twice while the Menu screen is displayed, the Menu screen is disappeared.

2. Use the [ ] and [ ] buttons to perform adjustment.

Pressing the [ ] button, shift the screen to the buttom. Pressing the [ ] button, shift the screen to the top.

3. Press the [ENTER] button, to save the preset data and be back to

the Menu screen.

Press the [MENU] button, to cancel this procedure and be back to the Menu screen. In this case, the preset data is not saved.

VERT. POSITION DOWN UP

Adjust the Horizontal Position

The adjustment flow is described in below:

Display the Sub-Menu Screen

By pressing the [MENU] button while the Menu screen is displayed, the Sub-menu is displayed on screen.

Select the item to be adjusted

Select the item to be adjusted by moving the cursor on the Sub-menu screen with the [ ] button and/or [ ] button.

Adjustment or Setting

For each item selected, the adjustment/ setting has been made by pressing the [ ] button and/or [ ] button. Press the [ENTER] button to save the data. (The detail steps for each item are described at the page 19 - 22)

Disappearance of Sub-menu Screen

By pressing the [MENU] button while the Sub-menu screen displayed, the Submenu screen is disappeared. No key entry has been for more than 20 second, the Sub-menu screen is also disappeared.

･Adjust the level of color (RED/GREEN/BLUE) ･Cancel all data adjusted/saved and set the

data back to default data

･Display the input signal data ･Adjust the black level

･To change the language used in OSD (On

Screen Display)

COLOR RECALL VIDEO MODE BLACK LEVEL LANGUAGE ENGLISH

2019

LCD Monitor Instructions

Adjustment Procedure (Sub-menu Screen)

Adjust the color level (RED / GREEN / BLUE)

A LCD Monitor is shipped from manufacturer with all the color settings at a standard level. In most cases no further adjustments are necessary. However, depending on the computer connected to the monitor, some colors may not appear correctly. If this happens, please make adjustments in the following way. The value set in this section is applied to all display mode available on a LCD Monitor.

1. Select "COLOR" on the Sub-menu screen.

･Return to the color setting to default ･Adjust the Color Level in RED

･Adjust the Color Level in GREEN

･Adjust the Color Level in BLUE

COLOR

DEFAULT USER R

USER G

USER B

(Ex.)

----------------------- -------

2. Move the cursor on this screen with the [ ] button and/or the [ ]

button, select the color you wish to adjust, and then press the [ENTER] button.

In case the DEFAULT is selected, after the screen shows at the standard color, be back to the Sub-menu screen. In case that one of USER is selected, the color of screen is switching to user mode.

3. Adjust the Color Level with the [ ] button and/or the [ ] button,

and then press the [ENTER] button. By depression of the [ENTER] button, adjusted data is saved.

4. Pressing the [MENU] button to return the Sub-menu screen.

Delete the data saved at the current display mode

Delete the entire saved data / reload the data progammed by manufacture

It is possible to delete the data saved at the current display mode, and load the data programmed by manufacturer.

1. Select "RECALL" on the Sub-menu screen.

2. Press the [MENU] or [ENTER] button.

By pressing of the [ENTER] button, all data adjusted/saved has been deleted, the data programmed by manufacturer has been reloaded, and then be back to the Sub-Menu screen. By pressing of the [MENU] button instead of [ENTER] button, return the Sub-menu screen without affecting any adjusted/set data.

RECALL

ENTER EXECUTE MENU CANCEL

a a

2. Select 'CLEAR' or 'ABORT' with the [ ] button or the [ ] button,

and then press the [ENTER] button.

In case the 'CLEAR' is selected, all saved data are cleared for all mode (VGA / SVGA). In case the 'ABORT' is selected, to terminate this sequence without affecting any to the saved data.

Delete the adjusted/saved data for all mode(VGA / SVGA) at one time and load the data programmed by manufacturer.

1. On the Menu screen, press [MENU] button and [ENTER] button

simultaneously. The following message is displayed on screen

CLEAR PARAMETERS

CLEAR ABORT

(Ex.)

USER R

----------------------- -------

[ 22]

LCD Monitor Instructions

Adjustment Procedure (Sub-menu Screen)

note P: Polarity (+)

N: Polarity (-)

Displays information on the current mode.

1. Select "VIDEO MODE" on the Sub-menu screen.

2. Press the [ENTER] or [MENU] button and be back to the Sub-menu

screen.

･Vertical Synchronizing Signal Frequency

･Horizontal Synchronizing Signal Frequency ･Vertical Synchronizing Signal Polarity ･Horizontal Synchronizing Signal Polarity

･Resolution

VERT. SYNC

60.5Hz HOR. SYNC

37.9kHz VERT. POLARITY P HOR. POLARITY N RESOLUTION 800x600

(Ex.)

note

Display the information of input signal Adjust the Black Level

Select Language used in OSD (On Screen Display)

The Black Level is adjusted for full screen basis. The value set in this section is applies to entire mode available on this LCD Monitor.

1. Select "BLACK LEVEL" on the Sub-menu screen.

2. The Black Level is adjusted by pressing the [ ] button and/or the

[ ] button.

3. Press the [ENTER] button to save the content of adjustment, and be

back to the Sub-menu screen.

Press the [MENU] button and be back to the Sub-menu screen. The content of adjustment has not been saved.

2. Select the language with the [ ] button and/or the [ ] button.

3. By depression of the [ENTER] button, the data is saved.

The LANGUAGE appeared on OSD screen has been changed, and then OSD screen is disappeared.

Press the [MENU] button and return the Sub-menu screen. In this case, the language information selected has not been saved.

1. Select "LANGUAGE" on the Sub-menu screen

LANGUAGE ENGLISH DEUTSCH FRANCAIS ESPANOL

BLACK LEVEL

(Ex.)

------------------------------

[ 0]

LCD Monitor Instructions

Additional Functions

OSD Key Lock (Lock and Unlock Screen Adjustment Buttons)

Adjust the contrast

It is possible to lock the operation to prevent unauthorized or unintentional changes.

1. Turn the power 'OFF'. And turn 'ON', while pressing the [MENU], [ ]

and [ ] buttons simultaneously.

The following message is displayed.

After this setting, all of button entries related to adjustment are prohibited. This setting remains the same, even if the power "OFF"

• In order to unlock this mode, turn the power 'OFF' then on again while pressing the [MENU], [ ] and [ ] buttons, simultaneously.

By pressing the [ ] button, the contrast on screen becomes darker. By Pressing the with [ ] button, the contrast on screen becomes lighter.

1. When the OSD (On Screen Display) is not displayed, it is possible to

adjust contrast on screen with [ ] and [ ] buttons.

2. Press the [ENTER] button to save the content of adjustment.

Press the [MENU] button, to display the value before adjustment and disappeare the OSD Screen. By this operation, the value adjusted is not saved.

In the cycle of adjustment, if no key depression has been continuing for more than 10 seconds, the OSD screen is disappeared without storing any figures on a display.

This is the function to reduce the monitor's power consumption, when a Computer has not been used for long, even when the power to a LCD Monitor is "ON". In order to activate this system, it must be connected and used with a computer that conforms to DPMS (Display Power Management Signaling) Standard of the VESA (Video Electronics Standards Association).

This Monitor conforms to DDC1(Display Data Channel 1) standard as well as DDC2B (Display Data Channel 2B) standard of VESA. (DDC stands for display channel and is a registered trade mark of VESA)

Plug and Play

Power Management System

This Monitor will indicate the status of input signal with LED lamp.

Green Fully ON Be Input Signal

Amber Fully ON Stand-by (No Vertical / Horizontal Frequency Signal)

Signal Cable Dis-connected

OFF Power OFF

Power Indicator

OSD KEY LOCKED

(Ex.)

CONTRAST

----------------------- -------

[ 25]

Fault Finding

TroubleshootingMaintenance

Always unplug the AC power plug from the outlet when performing maintenance. Also unplug the cables from the computer.

Cabinet

Soak a soft cloth in water or neutral detergent, wring well, and wipe the cabinet gently. Never use solvents such as paint thinner or benzene as they will damage the surface of the cabinet. Follow the manufacturer’s directions when using chemically treated cloths.

Display Screen

LMU-TK12AS2

Gently blow away any dust that has adhered to the display screen. Apply a small amount of ethyl alcohol or isopropyl alcohol to a soft cloth and wipe gently. Do not wipe with plain water. Do not use organic solvents such as acetone or toluene. Do not rub with pointy objects such as a pen or screwdriver.

LMU-TK12AS2TC

Gently sweep away any dust with a dried cloth, when the dust is on the surface of a Touch Screen. In case that a Touch Screen is dirty enough, gently wipe the surface of a Touch Screen with a soft, clean cloth dampened with a small amount of water or applicable cleaner. Don't rub with pointry objects such as a balled point pen or screwdriver.

Applicable Cleaner:

• Isopropyl Alcohol

• Neutral Detergent (water down)

• Glass Cleaner without containing polisher

• Glass Cleaner (Non-ammonium type)

★Never use solvents such as thinner, benzene or acid detergent as they will

damage the surface of a Touch Screen.

LMU-TK12AS2TR

Gently blow away any dust that has adhered to the display screen. To clean off dirt, use a cloth dampened with water or isopropyl alcohol. Don't use organic solvents such as acetone or toluene. Avoid scratching the monitor with pens, screwdrivers or other sharp implements.

Check the following items before requesting repair. When the monitor still does not function properly after checking these items, stop using it, turn off the power switch, unplug the power plug from the outlet, and contact the store where it was purchased.

Problem Check Item Treatment

Page No.

Power indicator does Is the power turned on ? Check the outlet, DC jack con-

3-6

not light. nection, and the power switch. No picture (when the Is a screen-saver program Press any button or move the

power indicator being run ? mouse to end the screen-saver – shows fully on green) program.

No picture with Is the power to the computer Check that power is being NO SYNC DETECTED

turned on ? supplied to the computer – message (power program. indicator shows

Is the computer standing by Use the computer to end the

–

orange).

(suspended) ? standby status.

Is the RGB cable connected Check the RGB cable

securely ? connection. 9,10

Screen is not dis- Is the computer’s signal Check the computer manual played with Signal timing (horizontal or vertical and set the signal timing so Frequency Out of synchronous signals) over that it falls within the range for Range change Input the range specified for this this monitor’s specifications. 29,30 Signal Timings monitor ? message (power indicator shows fully on green).

Screen’s display Is the computer’s screen Reset the screen size refering range is incorrect size set correctly ? to computer manual. with Signal Frequency Out of

–

Range change Input Signal Timings massage.

Part of the screen is Is the screen adjusted Adjust the screen.

missing. correctly ? Picture is distorted. Is the RGB cable connected Check the RGB cable

9,10

securely ? connection.

Is the screen adjusted Adjust the screen correctly.

correctly ?

2827

Specifications

Table of Preset Data

• This monitor conforms to the SVGA mode (800 x 600 dots).

• Display is not possible even when the computer’s display mode is set to be

larger than the SVGA mode (800 x 600 dots). Use a mode that is smaller than SVGA.

• Displaying the same screen for an extended period of time may leave a residual image; this does not indicate a broken or defective display. The display will return to normal after the power is turned off and the unit stands for a while. Use of a screen saver is recommended.

• Bright dots (dots that remain lit) or black dots (unlit dots) on the LCD monitor’s display are normal; they do not indicate a broken or defective display.

Screen Display

Troubleshooting

The 8 signal timing patterns indicated in the tables below are preset when the monitor is shipped from the factory. Up to 7 additional timing pattern can also be stored. The timing pattern is automatically determined and displayed according to the synchronous signals of the computer being used. The monitor will use the closest timing pattern for display when a perfectly matched one is not available.

No. Resolution Vertical Frequency Horizontal Frequency

1 640 x 400 dots 70 Hz 31.4 kHz 2 640 x 480 dots 60 Hz 31.5 kHz 3 640 x 480 dots 73 Hz 37.8 kHz 4 640 x 480 dots 75 Hz 37.5 kHz 5 800 x 600 dots 56 Hz 35.1 kHz 6 800 x 600 dots 60 Hz 37.9 kHz 7 800 x 600 dots 72 Hz 48.1 kHz 8 800 x 600 dots 75 Hz 46.9 kHz

Cable Pin Arrangement (male)

Cable Pin Arrangement

No. Signal name No. Signal name No. Signal name

1 R 6 R GND 11 –– 2 G 7 G GND 12 DDC data line* 3 B 8 B GND 13 Hor. Sync. 4 –– 9 –– 14 Vert. Sync. 5 DDC GND* 10 GND 15 DDC clock line*

Video Input : mini D-Sub (15pin)

* DDC Standard (VESA)

1 5

6 10

11 15

Dimensions 294.4 (W) x 232.9 (H) x 42.7 (D) mm Weight 1.8kg Operating Conditions Operating Temperature: 5°C to 35°C

Humidity: 30% to 85% RH (no condensation)

Power Supply/AC Adapter Model Name: GI40-US1225

Input: 115-240VAC 1.0A-0.55A, 50-60Hz Output: DC 12V 2.5A

Power Consumption 16W (2W in Energy Saving mode)

Liquid Crystal Panel TFT Display Size 12.1'' Pixel Configuration 800 x 600 Pixel Pitch 0.308 x 0.308 mm Brightness 350 cd/m

Response Time 70 ms Contrast 350 : 1 typ. Angle of Visibility Up 40, Down 50, Right 55, Left 55 degrees

(contrast ratio of less than 10)

3029

Monitor specifications

Specifications

Note : To improve this LCD monitor’s performance level, its specifications and

appearance are subject to change without notice.

LCD

Video

Physical

Horizontal signal 31.4 - 48.1kHz Vertical signal 56 - 75Hz Video Signal Analog RGB 75ohm 0.7Vp-p No. of Colors 16.19 million OSD Language English, German, French, Spanish Plug & Play VESA DDC1, DDC2B Power Management VESA DPMS

Dimensions 294.4 (W) x 232.9 (H) x 42.7 (D) mm Weight 2.4kg (LMU-TK12AS2TC) 2.1kg (LMU-TK12AS2TR) Operating Conditions Operating Temperature: 5°C to 35°C

Humidity: 30% to 85% RH (no condensation)

Power Supply/AC Adapter Model Name: GI40-US1225

Input: 115-240VAC 1.0A-0.55A, 50-60Hz Output: DC 12V 2.5A

Power Consumption 17W (3W in Energy Saving mode)

Liquid Crystal Panel TFT Display Size 12.1'' Pixel Configuration 800 x 600 Pixel Pitch 0.308 x 0.308 mm Brightness 350 cd/m

Response Time 70 ms Contrast 350 : 1 typ. Angle of Visibility Up 40, Down 50, Right 55, Left 55 degrees

(contrast ratio of less than 10)

Note : To improve this LCD monitor’s performance level, its specifications and

appearance are subject to change without notice.

LCD

Video

Physical

Touch Screen

Type Capacitive(LMU-TK12AS2TC) Resistive (LMU-TK12AS2TR) Electrical Resolution 10bit (1,024 x 1,024) 4095 x 4095 (0.1 mm) Communication Bi-directional asynchronous RS-232C serial communication

LMU-TK12AS2TC / LMU-TK12AS2TRLMU-TK12AS2

SANYO Electric Co., Ltd. Printed in Japan

3RE6P11010790C

Sanyo LMU-TK12AS2, LMU-TK12AS2TC, LMU-TK12AS2TR Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual