SANYO EMV3405SW, EMV3405S User Manual

File No :File No :
File No :
File No :File No :
SUPPLEMENT OF SUPPLEMENT OF
SUPPLEMENT OF
SUPPLEMENT OF SUPPLEMENT OF SER SER
SER
SER SER
VICE MANUALVICE MANUAL
VICE MANUAL
VICE MANUALVICE MANUAL
MicrMicr
Micr
MicrMicr
owave Ovenowave Oven
owave Oven
owave Ovenowave Oven
Pr Pr
Pr
Pr Pr
See the Service Manual of EM-F3400SW (SM-860304) except the items described in this Service Manual.
EM-V3405SW (U.S.A.)EM-V3405SW (U.S.A.)
EM-V3405SW (U.S.A.)
EM-V3405SW (U.S.A.)EM-V3405SW (U.S.A.)
oduct Code No.oduct Code No.
oduct Code No.
oduct Code No.oduct Code No.
437 550 00437 550 00
437 550 00
437 550 00437 550 00
CAUTIONCAUTION
CAUTION
CAUTIONCAUTION
WW
ARNING TO SERARNING TO SER
W
ARNING TO SER
WW
ARNING TO SERARNING TO SER
VICE TECHNICIANSVICE TECHNICIANS
VICE TECHNICIANS
VICE TECHNICIANSVICE TECHNICIANS
SERVICING TO AVOID POSSIBLE EXPOSURE TO
EXCESSIVE MICROWAVE ENERGY
(a) Do not operate or allow the oven to be operated with the door open. (b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other
microwave source, and make repairs as necessary : (1) Interlock operation, (2) proper door closing, (3) seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and latches, (5) evidence of dropping or abuse.
(c) Before turning on microwave power for any service test or inspection within the microwave generating
compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment, integrity, and connections.
(d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation and
transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual before the oven is released to the owner.
(e) A microwave leakage check to verify compliance with the Federal per formance standard should be performed
on each oven prior to release to the owner.
REFERENCE NO. SS-860312
CAUTIONCAUTION
CAUTION
CAUTIONCAUTION
For micrFor micr
For micr
For micrFor micr
owave enerowave ener
owave ener
owave enerowave ener
gy emissiongy emission
gy emission
gy emissiongy emission
In the area emitting the highest reading, switch the meter to SLOW RESPONSE, and take a reading for minimum of three (3) seconds. We recommended the pattern outline shown below when the door surface is surveyed.
On every service calls, check for microwave energy emission, must be made according to the following manner.
MeasurMeasur
Measur
MeasurMeasur
Measurement must be made with the microwave oven operating at its maximum output and containing a load of 275±15 milliliters of tap water initially at 20 ±9oF) placed within the cavity at the center.
NOTENOTE
NOTE : The water container must be a 600 milliliter beaker
NOTENOTE
A properly operating door and seal assembly will normally register emission on greater than 4mW/cm2 to allow for measurement uncertainty with the cooking shelf or tray in place.
All repairs must be performed in such a manner All repairs must be performed in such a manner
All repairs must be performed in such a manner
All repairs must be performed in such a manner All repairs must be performed in such a manner micrmicr
micr
micrmicr
Follow the instructions supplied with a detector being used and performed an R.F. emission test around the door front and edges and all edges and vent of the outer case. The cabinet (wrapper) must be in place and the oven fully assembled.
When performing emission survey, with the meter on FAST RESPONSE the movement of a detector probe shall not exceed one (1) inch per second.
ement of enerement of ener
ement of ener
ement of enerement of ener
and made of an electrically none conductive material such as glass or plastic. The cook tray must be in place when measuring emission.
owave enerowave ener
owave ener
owave enerowave ener
gy emissiongy emission
gy emission
gy emissiongy emission
gy emission argy emission ar
gy emission ar
gy emission argy emission ar
e minimal.e minimal.
e minimal.
e minimal.e minimal.
o±5o
celsius (68
thatthat
that
thatthat
NOTENOTE
NOTE : Periodically check to be sure that the probe tip is
NOTENOTE
not worn or dirty.
The following U.S. standard applies to microwave ovens : 21 CFR 1030.10, Performance Standard for Microwave Ovens.
It requires that the power density of the microwave radiation emitted by a microwave oven shall not exceed five (5) milliwatts per square centimeter at any point 5 centimeter (about 2 inches) or more from the external surface of the oven.
All microwave ovens exceeding the emission level of 4mW/cm microwave ovens and the manufacturer immediately and the owner should be told not to use the microwave oven until it has been repaired completely.
If a microwave oven is found to operate with the door open, report to Dept. of Service, the manufacturer and CDRH* immediately. Also tell the owner not to use the oven. *CDRH : Center for Device and Radiological Health.
The interlock monitor switch acts as the final safety switch protecting the customer from microwave radiation. If the interlock monitor switch operates to blow the fuse with interlocks failed, you must replace all interlock switches primary and secondary interlock switches and the monitor switch with new ones because the contacts of those interlock switches may be melted and welded together.
2
must be reported to Dept. of Service for
- i -
- TABLE OF CONTENTS -
Specifications .................................................................. 1
Power Output Measurement ........................................... 1
Circuit Diagram ............................................................... 2
1. SPECIFICA1. SPECIFICA
1. SPECIFICA
1. SPECIFICA1. SPECIFICA
Rated Power Consumption ... 1650W.
Microwave Output ................. 1050W.
Frequency .............................. 2,450MHz±50MHz.
Power Supply ......................... 120V±12V, 60Hz.
Rated Current ........................ 14.3 Amp.
Safety Devices ...................... Thermal Fuse open at
Timer ...................................... Electronic Digital, up to
Overall Dimensions ............... 2011/16”(W) x 1615/16”(D) x 113/8”(H).
Oven Cavity Size ................... 1313/16”(W) x 145/8”(D) x 83/16”(H).
Turn Table Diameter ............... 1013/16”
Effective Capacity of
Oven Cavity ........................... 1.2 Cubic Feet.
Net Weight ............................ Approx. 35.5 Lbs.
TIONSTIONS
TIONS
TIONSTIONS
o
F (167oC) for Cavity.
Thermal Protector open at
o
F (135oC) for Magnetron, Fuse (Cartridge Type 20A), Primary Interlock Switch, Door Sensing Switch and Relay 2. Interlock Monitor Switch.
99min. 99 sec.
Test Procedures ...................................................... 3
Exploded View and Parts List ................................ 4 ~ 9
Overall Circuit Diagram .......................................... 10
(C) 1. Set cooking time to two (2) minutes. (“2 00”
appears in display)
2 . Touch “START” key and operate oven for exactly
two (2) minutes.
(D) 1. Take out the two bowls at once.
2 . Stir both water with thermometer and measure the
water temperature rise respectively.
(E) 1 . Get temperature rise by calculation the difference
(water temperature after cooking minus initial temperature) in each bowl.
2 . Then calculate average value(t) of both temperature
rises in degrees centigrade.
3. Then work out :
Power Output (watt) = 70 x ∆t
2. POWER OUTPUT MEASUREMENT2. POWER OUTPUT MEASUREMENT
2. POWER OUTPUT MEASUREMENT
2. POWER OUTPUT MEASUREMENT2. POWER OUTPUT MEASUREMENT
NOTENOTE
NOTE
NOTENOTE
The Power Output specification 1050W on this model is measured with IEC measurement. The Power Output is measured with two (2) liters water is equivalent to 1050W in measurement with IEC, when measured with the following Power Output.
(A) 1 . Fill two test bowls with each 1 liter water respectively.
2 . Use accurate thermometer and measure each
water temperature respectively.
(B) Place the two bowls on glass turntable.
Where t is an Average Temperature Rise in degrees centigrade.
(F) Power Output shall be in the following range :
Average Microwave Temperature Rise Power Output
Minimum
24.3oF (13.5oC) 945W
Maximum
31.1oF (17.3oC) 1211W
(G) Power Output will be influenced by line voltage of
power supply. Consequently, correct Power Output must be measured within 120V AC ± 1 volt while unit is operating.
- 1 -
3. CIRCUIT DIAGRAM3. CIRCUIT DIAGRAM
3. CIRCUIT DIAGRAM
3. CIRCUIT DIAGRAM3. CIRCUIT DIAGRAM
WIRING COLOR
O : ORANGE B K : BLACK
R : RED BL : BLUE
W : WHITE Y : YELLOW
- 2 -
Figure 1Figure 1
Figure 1
Figure 1Figure 1
4. TEST PROCEDURES4. TEST PROCEDURES
4. TEST PROCEDURES
4. TEST PROCEDURES4. TEST PROCEDURES
COMPONENT COMPONENT
COMPONENT
COMPONENT COMPONENT
TOUCH KEY BOARD
--
-
--
CHECKOUT PROCEDURE CHECKOUT PROCEDURE
CHECKOUT PROCEDURE
CHECKOUT PROCEDURE CHECKOUT PROCEDURE
Measure the resistance between terminals of FPC connector after removing it from S101. (Figure 2).
NOTE NOTE
NOTE
NOTE NOTE
- When reconnecting the FPC connector, make When checking “START” key, connect sure the holes on the connector are properly Ohm-Meter as illustration below inserted in hooks of the plastic fastener in S101.
MAMA
065
TOTAL
1
7
DEFROST
TRIX CIRCUIT FORTRIX CIRCUIT FOR
MA
TRIX CIRCUIT FOR
MAMA
TRIX CIRCUIT FORTRIX CIRCUIT FOR
TOUCH KEY BOARD TOUCH KEY BOARD
TOUCH KEY BOARD
TOUCH KEY BOARD TOUCH KEY BOARD
FPC CONNECTORFPC CONNECTOR
FPC CONNECTOR
FPC CONNECTORFPC CONNECTOR
POWER
LEVEL
QUICK
ON
SOUP /
BEVERAGE
POTATO
MORE + LESS -
RESUL RESUL
RESUL
RESUL RESUL
Resistance value
Ohm-MeterOhm-Meter
Ohm-Meter
Ohm-MeterOhm-Meter
TT
T
TT
When When not touched touched
Less than More than 1K Ohms 1 MEG Ohms
..
.
..
2
3
4
HIGH-VOLTAGE TRANSFORMER
8
9
STOP / CLEAR
PIZZA SLICE
FRESH
VEGETABLE
1) Measure the resistance : Normal readings : With an Ohm-Meter on R x 1 scale. a. Primary winding : Approximately 0.30 Ohms. b. Filament winding : Less than 1 Ohm. c. Secondary winding : Approximately 74.2 Ohms.
2) Measure the resistance : Normal readings : With an Ohm-Meter on highest scale. a. Primary winding to ground : Infinite Ohms. b. Filament winding to ground : Infinite Ohms.
Ohm-MeterOhm-Meter
Ohm-Meter
Ohm-MeterOhm-Meter
QUICK
DEFROST
START
CLOCK
FROZEN ENTREE
FROZEN
VEGETABLE
POPCORN
KITCHEN
TIMER
ADD
30 SEC
CUSTOM
PROGRAMS
TERMINALS OF FPC CONNECTORTERMINALS OF FPC CONNECTOR
TERMINALS OF FPC CONNECTOR
TERMINALS OF FPC CONNECTORTERMINALS OF FPC CONNECTOR
Figure 2Figure 2
Figure 2
Figure 2Figure 2
Note Note
Note : Remove varnish of
Note Note
measured point.
- 3 -
Figure 3Figure 3
Figure 3
Figure 3Figure 3
5.5.
EXPLODED VIEW AND PEXPLODED VIEW AND P
5.
EXPLODED VIEW AND P
5.5.
EXPLODED VIEW AND PEXPLODED VIEW AND P
CAVITY PARTS
ARAR
AR
ARAR
TS LISTTS LIST
TS LIST
TS LISTTS LIST
* * * ALL SERVICE ON MICROWAVE OVENS SHOULD BE PERFORMED BY A QUALIFIED TECHNICIAN USING
APPROVED TESTING EQUIPMENT. CUSTOMERS SHOULD NOT ATTEMPT TO REPLACE PARTS IDENTIFIED BY A TRIPLE ASTERISK (***).
Key
No.
Part No. Description Q’ty
1 617 228 8321 Cabinet 1 2 411 082 5201 SCR TPG TRS 4 x 10 Z1 8 3 411 160 6007 SCR TPG TRS + SRT 4 x 10 Z1 2 4 617 235 3234 Power Cord 1 5 411 160 6106 SCR S-T TRS + SRT 4 x 10 Z1 1 6 617 235 2329 Oven Cavity*** (Not Service Part) 1 7 617 124 1068 Gear Motor 1 8 411 010 5808 SCR EVR PAN 4 x 10 Z1 2 9 617 138 5601 Bottom Plate*** (Not Service Part) 1 10 617 221 6089 Plastic Foot with Canoe Clip 4 11 411 011 0802 Bolt Hex + SW + W5 x 14 Z1*** 2 12 617 223 3116 Hinge, Lower*** 1 13 411 089 2500 Washer F 5 x 10 x 0.8 1
NoteNote
Note : Screws securing Cabinet cannot be removed by regular screwdriver.
NoteNote
KEY NO. 26. SPECIAL SCREW REQUIRES SPECIAL DRIVER (PART NO. 617 209 3734) OR SPECIAL BIT (PART NO. 617 209 3741)
Key
No.
Part No. Description Q’ty
14 617 120 8481 Insulation Sheet 1 15 617 220 9401 Turn Table Shaft 1 16 617 204 9489 Roller Base Assy 1 17 617 200 0657 Rotating Tray 1 18 617 235 2398 Antenna Complete 1 19 617 235 2435 Cavity Cover 1 20 411 069 1707 SCR TPG TRS 4 x 6 DA 1 21 411 006 6604 SCR TPG PAN 3 x 6 Z1 1 22 617 200 0381 Thermal Fuse 167oC1 23 617 080 5315 Special Washer 1 24 25 26 617 229 9013 Special Screw 2
- 4 -
SWITCHES AND MICROWAVE PARTS
*** ALL SERVICE ON MICROWAVE OVENS SHOULD BE PERFORMED BY A QUALIFIED TECHNICIAN USING
APPROVED TESTING EQUIPMENT. CUSTOMERS SHOULD NOT ATTEMPT TO REPLACE PARTS IDENTIFIED BY A TRIPLE ASTERISK (***).
Key
No.
Part No. Description Q’ty
1 411 082 5201 SCR TPG TRS 4 x 10 Z1 10 2 617 235 3319 H.V Transformer,*** N6T-V3405 1
120V 60Hz 3 617 199 8283 Stay, Cavity & Magnetron 1 4 411 006 6604 SCR TPG PAN 3 x 6 Z1 1 5 617 129 1001 Thermostat, Magnetron 135oC1 6 415 002 6101 Magnetron, 2M219H(B)A-*** 1 7 423 020 3408 Fuse, 125V 20A 1 8 617 235 3302 Fuse Holder 1 9 617 221 3606 Lead Wire Ass’y (including Diode) 1 10 617 162 1990 Blower Base 1 11 617 235 3326 H.V Capacitor including Resistor, 1
1.0uf 2.3KV 12 617 182 2373 Capacitor Band 1 13 411 011 5609 Bolt Hex 4 x 10 Z1 4 14 617 235 1551 Duct, Mag. Exhaust 1 15 617 005 5147 Lamp, 120V 20W 1 16 617 230 2713 Lamp Socket 1 17 617 197 7417 Blower Motor 1
Key
No.
Part No. Description Q’ty
18 411 082 5201 SCR TPG TRS 4 x 10 Z1 2 19 617 196 8507 Blower Fan 1 20 617 245 6256 Latch Lever*** 1 21 617 221 4078 Micro Switch,*** Primary Interlock 1
AM51630C53F2
22 617 221 4061 Micro Switch,*** Interlock Monitor 1
AM50620C53
23 617 221 4078 Micro Switch,*** Door Sensing 1
AM51630C53F2 24 617 124 1198 Latch Lever,*** 1 25 617 245 6096 Lever Stopper*** 1 26 411 102 5907 SCR ETG TRS 4 x 10 N2 2 27 411 129 5805 SCR TPG BIN 3 x 10 Z1 1 28 617 226 2987 Harness, Door Sensing 1 29 617 124 3796 Lead Wire Ass’y 1 30 617 235 3173 Duct, (MQ In) 1 31 617 221 7857 Duct, (MQ In) 1 32 617 235 2534 Duct, (H.V.Trans.) 1
- 5 -
DOOR PARTS
* * * ALL SERVICE ON MICROWAVE OVENS SHOULD BE PERFORMED BY A QUALIFIED TECHNICIAN USING
APPROVED TESTING EQUIPMENT. CUSTOMERS SHOULD NOT ATTEMPT TO REPLACE PARTS IDENTIFIED BY A TRIPLE ASTERISK (***).
Key
No.
Part No. Description Q’ty
1 617 235 2282 Door Cover*** 1 2 617 228 0783 Door Panel*** 1 3 617 228 7591 Door Main Frame*** (Also 1
order Door Sheet when replacing Door Main Frame)
4 617 228 6242 Choke Dielectric*** 1
Key
No.
Part No
5 617 228 9878 Door Sheet 1 6 411 054 1903 Nut Hex + Flg W / SRT 5*** 2 7 617 223 3109 Hinge, Upper*** 1 8 411 011 0802 Bolt Hex + SW + W 5 x 14*** 2 9 617 101 1494 Spring*** 1 10 617 228 6068 Door Latch*** 1
. Description Q’ty
- 6 -
CONTROL PANEL PARTS
* * * ALL SERVICE ON MICROWAVE OVENS SHOULD BE PERFORMED BY A QUALIFIED TECHNICIAN USING
APPROVED TESTING EQUIPMENT. CUSTOMERS SHOULD NOT ATTEMPT TO REPLACE PARTS IDENTIFIED BY A TRIPLE ASTERISK (***).
Key
No.
Part No. Description Q’ty
1 617 235 3203 Control Sheet*** (Also order 1
Touch Key Board when replacing Control Sheet)
2 617 230 9019 Touch Key Board*** (Also order 1
Control Sheet when replacing Touch Key Board)
3 617 235 7089 Control Frame*** 1
Key
No.
Part No. Description Q’ty
4 617 228 0752 Control Base*** 1 5 411 160 6205 SCR TPG TRS+SRT 4 x 10 Z1 1 6 617 230 8210 Power & Control Circuit Board*** 1 7 411 129 5805 SCR TPG BIN 3 x 10 Z1 2 8 617 080 9559 Spring, Door Release Lever*** 1 9 617 235 7072 Door Release Lever*** 1
PRINTED MATTER (Items Not Illustrated)
Key
No.
Part No. Description Q’ty
617 235 3418 Operating Instructions 1
(English / Spanish) 617 235 4279 Carton Box Complete 1 617 235 3135 Name Plate 1
- 7 -
CONTROL CIRCUIT BOARDCONTROL CIRCUIT BOARD
CONTROL CIRCUIT BOARD
CONTROL CIRCUIT BOARDCONTROL CIRCUIT BOARD
(Part No.
617 230 8210617 230 8210
617 230 8210)
617 230 8210617 230 8210
4160041600
41600
4160041600
- 8 -
CONTROL CIRCUIT BOARDCONTROL CIRCUIT BOARD
CONTROL CIRCUIT BOARD
CONTROL CIRCUIT BOARDCONTROL CIRCUIT BOARD
(Part No.
617 230 8210617 230 8210
617 230 8210)
617 230 8210617 230 8210
Key No. Order Part No. Description Q’ty
INTEGRATED CIRCUIT.
IC11 409 484 9804 IC LM8903-155FP 1
TRANSISTORS.
Q104 405 011 8609 2SC1740S-S-TP 1 Q101, 105 405 137 5803 DTA123YSATP 2 Q102, 103 405 139 0004 DTA143XSA-TP 2 Q11, 12 405 004 3000 2SA564A-Q-TP 2
DIODES.
D11, 12 407 012 0200 IN4002-TP 2
D101 ~ 107 407 012 4406 ISS133-T77 7
ZD101 407 132 2306 HZS3.9NB2 1
ZD11 407 057 0500 RD5.6ESB3 1
ZD12 407 160 6703 RD27ESB1 1
ZD13 407 132 2306 HZS3.9NB2 1
Key No. Order Part No. Description Q’ty
RESISTORS.
R105 401 012 4404 Carbon, 100 ohms 1
R101, 112 401 012 5609 Carbon, 1K ohms 7 121 ~ 125 ± 5%, 1/4W.
R15, 102, 401 012 6903 Carbon, 10K ohms 4 109, 114 ± 5%, 1/4W.
R16, 57 401 013 6308 Carbon, 12K ohms 2
R13, 14 401 016 2505 Carbon, 220 ohms 2
R11 401 016 3700 Carbon, 2.2K ohms 1
R106, 107- 401 016 9603 Carbon, 27 ohms 2
R113 401 017 1705 Carbon, 2.7K ohms 1
R110 401 018 2701 Carbon, 330 ohms 1
R111 401 018 3708 Carbon, 3.3K ohms 1
R108, 401 020 1907 Carbon, 4.7K ohms 7 115 ~ 120 ± 5%, 1/4W.
R51, 52, 54, 401 020 2805 Carbon, 47K ohms 4 103 ± 5%, 1/4W.
R12 401 021 2903 Carbon, 5.6K ohms 1
R104 401 023 1607 Carbon, 820 ohms 1
± 5%, 1/4W.
± 5%, 1/4W.
± 5%, 1/4W.
± 5%, 1/4W.
± 5%, 1/4W.
± 5%, 1/4W.
± 5%, 1/4W.
± 5%, 1/4W.
± 5%, 1/4W.
± 5%, 1/4W.
CAPACITORS.
C102 403 002 4708 Ceramic, 0.1mfd, 1
C105 ~ 107 403 069 8305 Ceramic, 0.01mfd, 3
C101 403 147 8807 Electrolytic, 1mfd, 1
C13 403 147 8609 Electrolytic, 47mfd, 1
C12 403 152 7307 Electrolytic, 100mfd, 1
C11 403 188 8408 Electrolytic, 470mfd, 1
± 5%, 25V.
± 5%, 50V.
± 20%, 50V.
± 20%, 10V.
± 20%, 35V.
± 20%, 25V.
MISCELLANEOUS.
BZ1 420 000 6800 Buzzer PKM22EPT. 1 VST1 407 118 5505 Varistor ENC 471D-10A. 1 DT1 617 185 3735 Display Tube. 1 RL1 617 201 3978 Relay, G5N-1A-DC12. 1 RL2 617 201 3954 Relay, G5G-1A DC12 1 RS1 617 128 3372 Ceramic Oscillator 1 S 1 617 234 8759 Connector. 1 S101 617 126 8959 Connector, 11P 1 S102 617 213 7582 Connector. 1 PT 1 617 178 3933 Step-down Transformer 1
2 617 079 4107 Part Base. 1 J1 ~ 6, 9 617 079 4299 Jumper. 7 J101 ~ 109 617 079 4237 Jumper. 9
P6TK-N101.
- 9 -
Loading...
+ 25 hidden pages