SANYO DSA14C Datasheet

SANYO Electric Co.,Ltd. Semiconductor Company

TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN

Ordering number : ENN6516

DSA14

Diffused Junction Silicon Diode

DSA14

Power Rectifier

Features

•

Facilitates automatic mounting and miniaturization in end products.

• Peak reverse voltage : V

• Average rectified current : I

=200, 600V.

=1.4A.

Package Dimensions

unit : mm

1301

[DSA14]

Cathode mark

7.6

1.6

0.1

1.6

2.0

4.0

2.8

SANYO : LHP

1.5

0.2

C 0.8

Specifications

Absolute Maximum Ratings at T a=25°C

Peak Reverse Voltage V Average Rectified Current I

Surge Forward Current I

Junction T emperature Tj → 150 °C Storage T emperature T stg -→ -55 to +150 °C

Parameter Symbol Conditions DSA14C DSA14G Unit

50Hz sine wave, mounted on an alumina board → 1.4 A

Load resistor Mounted a PCB → 1.1 A

FSM

50Hz sine wave → 60 A non-repetitive, 1 cycle peak value

200 600 V

Electrical Characteristics at Ta=25°C

Forward Voltage V Reverse Current I Thremal Resistance θi-l Junction-Lead 24 °C/W

Parameter Symbol Conditions min typ max Unit

θi-a Junction-Ambient Mounted on an 90 °C/W

Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications.

SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO products described or contained herein.

IF=1.4A 1.05 V VR=V

almina board Mounted on a PCB 120 °C/W

10 µA

41000 GI IM

No.6516-1/2

1.6

Resistive, inductive load

1.4

-- A

Capacitive

1.2

load Capacitive

1.0

load

0.8

Resistive,

0.6

inductive load

Mounted on a PCB

0.4

Average Rectified Current, I

0.2

-- Ta

Mounted on an alumina board

DSA14

7 5

-- A

1.0 7

Forward Current, I

3 2

Ta=150°C

-- V

25°C

0 20 40 60 80 100 120 140 160

Ambient Temperature, Ta -- °C

-- n

-- A

FSM

Surge Foward Current, I

2537

1.0 10

FSM

50Hz

2537

Number of Cycles at 50Hz, n

Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer’s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer’s products or equipment.

SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design.

In the event that any or all SANYO products(including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law.

No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co. , Ltd.

Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO product that you intend to use.

Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties.

IT02129

IT02131

100

0.1

0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6

Forward Voltage, V

-- V

IT02130

This catalog provides information as of April, 2000. Specifications and information herein are subject to change without notice.

No.6516-2/2