Sanyo DC-MP9500 User Manual

INSTRUCTION MANUAL

Micro Component System

DC-MP9500

DISPLAY

REMOTE CONTROLLER RB-MP8000

FM MODE/

REPEAT

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS OVRIR.

PRECAUTIONS

CAUTION

THIS PRODUCT CONTAINS A LOW POWER LASER DEVICE. TO
ENSURE CONTINUED SAFETY DO NOT REMOVE ANY COVERS
OR ATTEMPT TO GAIN ACCESS TO THE INSIDE OF THE PROD­UCT. REFER ALL SERVICING TO QUALIFIED PERSONNEL.

CLASS 1 LASER PRODUCT

LUOKAN 1 LASERLAITE

KLASS 1 LASERAPPARAT

- The apparatus shall not be exposed to dripping or splashing.

- Do not use where there are extremes of temperature (below 5

o

C or

exceeding 35oC), or where direct sunlight may strike it.

- Because of the CD player’s extremely low noise and wide dynamic
range, there might be a tendency to set the volume on the amplifier
unnecessarily high. Doing so may produce an excessively large out­put from the amplifier which could damage your speakers.

- Sudden changes in the ambient temperature may cause condensa­tion to form on the optical lens inside the unit. If this happens, take out
the disc, leave the unit for about 1 hour, and then proceed to operate.

IMPORTANT

If the plug supplied with this equipment is not suitable for the socket
outlets in your home it should be cut off and replaced with the correct
type.

Disposal of Plug

If the non rewireable plug is to be cut off, the removed plug should be
disposed of carefully as there is a shock hazard should the plug be
inserted into a live socket.

Replacing Fuse

The detachable fuse cover must be replaced after changing the fuse.
Only a 3A fuse should be used and should comply with BS1362 and

should carry the ASTA mark

.

- The system’s speakers use powerful magnets. Do not place time­pieces, credit cards, cassette tapes or video tapes, etc. near the speak­ers.

- Do not install this equipment in a confined space, such as a book
case or built in cabinet.

- No object filled with liquids, such as vase, shall be placed on the ap­paratus.

- The rating label is located on the bottom of the unit.

The wires in the mains lead are coloured in accordance with the follow­ing code:

Blue Neutral

Brown Live
The wires in the mains lead must be connected to the terminals in the
plug as follows:

Wire colour Plug terminal marking

Blue N or Black or Blue

Brown L or Red or Brown
Do not connect either wire to the earth terminal.
If the mains plug contains a fuse this should be 3A, if a plug without a
fuse is used the distribution board fuse should not be greater than 5A.

The unit is not disconnected from the mains unless it is unplugged from the AC outlet.

-1-

CONNECTIONS

L ch speaker

LEFT

SPEAKERS

(6Ω MIN.)

RIGHT

R ch speaker

+

_

_

+

LEFT

RIGHT

+

_

_

+

PHONES

SPEAKERS

(6Ω MIN)

RESET

LINE IN

FM Aerial

AM loop Aerial

AM

LOOP

FM

ANT

R

L

To an AC outlet

Video/Auxiliary equipment

Note:

- Do not connect the mains lead to an AC outlet until all connections
have been made.

- The system is not completely disconnected from the mains when the
z/ON button is set to the z position.

Speakers

Connect the connector of the left speaker lead to the “L” SPEAKERS
socket and the connector of the right speaker lead to the “R” socket.
If you have difficulty inserting the speaker lead connector, turn it over and
reinsert it.
When connecting the speakers, make sure that + and - polarities are
matched properly. Otherwise, the sound may appear to be lacking in the
bass range and stability.
Connect the red speaker wire to the red terminal + and the black wire to
the black terminal -.

FM Aerial

FM indoor aerial is sufficient to receive broadcasts. Extend the aerial wire
as straight as possible and, while listening to the sound from the system,
secure it in a position which yields minimal distortion and noise.

AM Loop Aerial

Assemble the loop aerial as shown in figure.

Unwind the aerial wires, then connect them
to the AM LOOP terminals. Place the loop
aerial in a position which yields the best AM
reception, or attach it to a wall or other sur­face as shown in figure.

Note:
To minimize noise, the speaker, mains and
any other leads should not come close to
the indoor or external aerial lead and AM loop
aerial. Do not place the aerial leads close to

Screws (not supplied)

the system.

Headphones

Connect stereo headphones (not supplied) to the PHONES socket (rear
of the unit) for monitoring or for private listening. The speakers are auto­matically disconnected when headphones are connected.

Video/Auxillary equipment

Connect audio leads (not supplied) from the audio output socket of a video/
auxilary equipment to the LINE IN sockets.

-2-

30˚30˚

CONTROLS

2

5

3

4

6

7

Controls

16

15
14

13

12

11
10

15

14

13

9
8

3

4 5

1. Power button ( z/ON)

2. Display

3. Control panel

i : CD play/pause button
f / _,+ / e : Skip/search/tuning/file select buttons

2

1

6

n : Stop button

4. Tuner function/band select button (TUNER/BAND)

5. Volume control button (VOLUME)

6. Function select button (FUNCTION)

7. Memory button (MEMORY)

8. Disc tray open/close button (OPEN/CLOSE)

7
8

9
10

11
12

9. FM mode/Display button (FM MODE/DISPLAY)

10. Random play button (RANDOM)

11. Repeat play button (REPEAT)

12. Clock/timer button (CLOCK/TIMER)

13. Tuner preset/Folder select button (TUNER PRESET/
FOLDER SELECT)

14. Disc tray

15. Remote sensor (IR)

REMOTE CONTROL

DISPLAY

FM MODE/

REPEAT

1. Power button ( z/ON)

2. Disc tray open/close button (OPEN/CLOSE)

3. Bass expander button (BASS)

1

4. Volume control buttons (VOL _, +)

5. CD play/pause button ( i )

6. Tuner function/band select button (TUNER/BAND)

7. FM mode/Repeat button (FM MODE/REPEAT)

8. Display button (DISPLAY)

9. Stop button ( n )

10. Skip/search/tuning/file select buttons
( f , _ TUNING/FILE +, e )

11. Sound preset button (SOUND)

12. Preset/folder select button
(PRESET/FOLDER SELECT)

13. Number buttons (1-9, 0)

14. Memory button (MEMORY)

15. Function button (FUNCTION)

16. Sleep button (SLEEP)

Number buttons (1-9, 0)

These buttons are used to select the track
numbers on a disc or preset radio stations.
If the function is “CD’’, the buttons select
the track numbers on a disc.
If the function is “TUNER”, the buttons se­lect preset radio stations.
With any other function, the buttons will
not function.

REMOTE CONTROLLER RB-MP8000

Inserting batteries

1 2

Two R03/AAA batteries

Note:
Always remove batteries if the remote control is not to be used for a month
or more. Batteries left in the unit may leak and cause damage.

(not supplied)

Remote control range

Remote sensor

Within approx. 7 meters

The buttons on the remote control perform similar functions to similarly
marked buttons on the front panel.

-3-

ADJUSTING THE CLOCK (Main unit only)

Example: To set “6:30”.
Turn the power off before setting. If this is the first time for setting, “0:00”
display blinks.

1. Press the CLOCK/TIMER button for
more than 3 seconds, “ ” blinks on
the display.

2. Press the MEMORY button. The
“hour” section and “ ” blinks.

3. Turn the VOLUME control to set the
“hour” section.

4. Press the MEMORY button to finish
the hour setting, the “minute” section
and “ ” blinks at the same time.

5. Turn the VOLUME control to set the
“minute” section.

6. Press the MEMORY button to finish
all settings and the clock starts.

- The time can be set accurately by pressing the MEMORY button

when a time signal is heard.

Note:

- To display the clock during operation, press the CLOCK/TIMER but­ton briefly. After a few seconds, the original display returns.

- If a power failure occurs or the mains lead is disconnected, the clock
display blinks. Reset the time again.

Changing the clock to the 12-hour display (Using the
main unit)

Example: 13:30 v PM1:30

1. Press the z/ON button to turn the power off and present time display.

2. While clock is displaying, press the MEMORY button on the main unit
and hold it, then press the TUNER PRESET/FOLDER SELECT but­ton on the main unit.

- To return the original setting, repeat the steps above.

BEFORE OPERATION

Turning the power on and off

- Press the z/ON button to turn on the unit, the display lights and “WEL­COME” will appear for several seconds.

- To turn the power off, press the z/ON button again, “GOOD BYE” will
appear for several seconds.

- When the unit is in standby, press the CLOCK/TIMER button to select
demonstration mode or clock display mode only.

- When the mains lead is connected to the AC outlet, the unit will re­spond to commands from remote control.

Direct start function

If the following buttons are pressed when the unit is in standby, the
unit turns on automatically and the function is set.
CD section i, TUNER/BAND
Remote control i, TUNER/BAND

Selecting the function

Press the FUNCTION button to select the desired function. Each time the
button is pressed, the display changes as follows:

CD v TUNER v LINE v CD v...

The function is automatically selected when CD play started or the TUNER/
BAND button has been pressed.
When the function selection is changed, CD play is automatically stopped.

Adjusting the volume

Turn the VOLUME control or press the VOL _ or + button on the remote
control to adjust the volume, the volume level appears on the display.
(VOL MIN, 1~ 39,MAX)

Press the BASS button again to close the bass sound, “ ” disap­pears on the display.

Selecting the sound mode (Remote control only)

Press the SOUND button to select the sound mode matching the music
below:

POP: Pops, etc.
CLASSIC: Classical music, etc.
ROCK: Rock music, etc.
JAZZ: Jazz, etc.

WHAT TO DO IF ...

If the operation of the unit or display is not normal,

1. Disconnect the main lead.

2. Press the RESET hole (rear of the unit) for at least 30 seconds.

3. Connect the main lead.

4. Resume operations.

RESET

AM

+

LEFT

_

_

RIGHT

SPEAKERS

+

(6Ω MIN)

PHONES

LINE IN

R

RESET

LOOP

FM
ANT

L

Bass expander system (Remote control only)

Press the BASS button to enhance the bass sound, “ ” appears on
the display.

-4-

CD PLAY

Use compact discs bearing the symbol shown. In
addition to conventional 12 cm CDs, this system can
be used to play 8 cm CDs without an adapter.

- This unit can play back the CD-R/RW that have
recorded music data as well. However, some CD-R/RWs cannot be
played back depending on the recording conditions.

- The CD-R/RW cannot be recorded in this unit.

1. Press the FUNCTION button to select CD function.

2. Press the OPEN/CLOSE button, disc tray slides out, “OPEN” appears.

3. Place the disc with the label fac­ing up on the disc tray. (Place only
one disc at a time.)

4. Press the OPEN/CLOSE button
again to close the disc tray.
“CLOSE” appears briefly, then the
total number of tracks and the to­tal playing time on the disc appears.

5. Press the i button. Play starts from
the first track. The current track
number and elapsed playing time are
displayed.

6. Press the n button to end disc play. When the last track has been
played, the player stops automatically.

Note:

- If the disc is loaded with the label side downward, or if a badly scratched
disc is loaded, “NO DISC” or “UNDISC” appears on the display. If this
occurs, load the disc correctly or replace the damaged disc.

Notes on handling compact discs

- Do not expose the disc to direct sunlight, high humidity or high tem­peratures for extended periods of time.

- Discs should be returned to their cases after use.

- Do not apply paper or write anything on the disc surface.

- Handle the disc by its edge. Do not touch the playing surface (glossy
side).

- Fingerprints and dust should be carefully wiped off the playing sur­face of the disc with a soft cloth.
Wipe in a straight motion from the centre to the outside of the disc.

- Never use chemicals such as record cleaning sprays, antistatic sprays
or fluids, benzene or thinner to clean compact discs.

To start play from the desired track

Select the track by using the f or e button, then press the i but­ton.

- The number buttons on the remote control can also be used for skip
play. To skip to track 6 while one track is playing, press 0, then 6 (for
normal music CD), or 0, 0, 6 (for MP3 CD).

Search play (forward/reverse)

If the f or e button is pressed during play, the player will search at
high speed in the forward or reverse direction while the button is being
pressed. When the button is released, normal play will continue.

Repeat play

Press the REPEAT button (or the FM MODE/REPEAT button on the re­mote control) before or during play. Press the button once, “1 REPEAT”
displays, repeat single track. Press the button twice, “ALL REPEAT” keeps
displaying, the unit will repeat all tracks or all programmed tracks.
To cancel repeat play, press this button again till “1 REPEAT” or “ALL
REPEAT” disappears.

Random play (Main unit only)

Press the RANDOM button, the player will automatically play disc option­ally, “RANDOM” will appear on the display screen.

Note:

- Press the n button to cancel random play.

- Random play will not function during programme play.

- If chosen random play when using MP3 disc, folder select function
can’t work.

Programmed play

Up to 24 tracks on a disc can be programmed for play in any order.

- First, select CD function and load a disc that you want to programme.

- The tracks must be programmed in the stop mode.

- The same track can be programmed more than once.

1. Press the MEMORY button in the
stop mode, “PROGRAM” appears
and blinks.

2. Press the f or e button to se-
lect a track.

- The number buttons on the remote control can also be used. In

this example, press 0, 6.

3. Press the MEMORY button.

4. Repeat steps 2 - 3 above to pro­gramme additional tracks.

Using the remote control
For normal music CD:

Press two number buttons within 4 seconds.
Example:

To select No. 3, press 0, 3.
To select No.10, press 1, 0.
To select No. 32, press 3, 2.

For MP3 CD:

Press three number buttons within 4 seconds.
Example:

To select No. 3, press 0, 0, 3.
To select No. 10, press 0, 1, then 0.
To select No. 125, press 1, 2, then 5.

Temporarily stopping play

Press the i button. To resume play, press the i button again.

Skip play

To skip to track 6 while track 3 is playing, press the e button repeatedly
until “6” appears (in the track section) on the display. To skip back to track 3
while track 6 is playing, press the f button repeatedly until “3” appears.

5. Press the i button to start pro­grammed play.

- When all programmed tracks have been played, the player stops au­tomatically.

- The programme contents are retained in memory.

- Any attempt to programme more than 24 tracks will result in “FULL”
being displayed and discontinuation of the programming.

- The programme contents are retained even if the function selection is
changed. Press the MEMORY button after selecting CD function, the
programmed contents appear.

Checking the programme

Each time the MEMORY button is pressed in the stop mode, the pro­grammed details sequentially appear on the display.

-5-

Changing a programme

To change a track

1. In the stop mode, press the MEMORY button repeatedly until the track
number to be replaced is displayed.

2. Press the f or e button to select a track as explained above.

3. Press the MEMORY button.

Note:

- Programmed details cannot be partially deleted or inserted.

MP3 CD PLAY

To add a new track to a programme

1. In the stop mode, press the MEMORY button repeatedly till
“-- -- -- -- . -- --” appears.

2. Press the f or e button to select a track as explained above.

3. Press the MEMORY button.

Cancel programme

- Press the n button once in the stop mode to cancel programmed play.

- After opening the disc tray, the programme contents will be cleared
away.

This unit can play back the CD-R/RW that has recorded music data or
MP3 files. Before playing back MP3 CD, please read the following.

MP3 CD information

- MP3 CD is the disc that standardized by ISO9660, its file name must
have the extension letters, “.MP3” or “.mp3”.

- Standard, sampling frequency, and the bit rate:
MPEG-1 Audio, layer 3
32kHz, 44.1kHz, 48kHz
32kbps - 320kbps (constant bit rate or variable bit rate)

- The recommend recording setting for a high-quality sound is 44.1kHz
of sampling frequency and 128kbps of constant bit rate.

- The directory and file names of the MP3 CD must be corresponded to
the ISO standardized files.

- Single-session disc can be played back.

- This unit can recognize up to 250 folders or 500 files per disc.
The CD disc with 251 folders or 501 files and over is not available to
this unit.

- This unit can recognize up to 8 directory trees per disc.

- MP3 CD may not be played in the recorded order.

- Music section in “CD Extra” can be played back, not Data section.

- “Mixed CD” can’t be played back.

Notes on disc writing method

There are three basic methods for writing to a CD: “Track-at-Once”, “Disc-
at-Once”, and “Packet Writing”.
Music files recorded by “Track-at-Once” or “Disc-at-Once” can be played
back on this unit. (Note: The unit can’t play back the music files added
with “Track-at-Once”.)
Music files recorded by “Packet Writing” can’t be played back.

Note:

- Some MP3 CDs can’t be played back depending on the recording
conditions.

- The CD-R/RW that has no music data or non-MP3 files can’t be played
back.

- Do not make an empty folder. It may not work correctly.

- In this model, recommend recording setting is 44.1KHz of the sample
frequency and 128kbps of constant bit rate. If files are recorded in
other bit rate (for example: 320kbps) or in variable bit rate, track-jump
may sometimes happen according to recording conditions.

MP3 CD Play

1. Turn the power on and choose CD function.

2. Load the MP3 CD.
The total number of folders and tracks
appear on the display.

3. Press the TUNER PRESET/FOLDER
SELECT button (or the PRESET/
FOLDER SELECT button on the re­mote control) to select the desired
folder.

Desired folder

4. Press the f or e button to select the desired track.

5. Press the i button to start play, the
track number and elapsed playing
time will display on the screen.

Limitations on display

Available letters for display are the following: capital alphabets of A through
Z, numbers of 0 through 9 and _ (underline).

MP3 CD directory sample

Playback order: song01 v song02 v ... v song14
Folder number F01

There is no MP3 file. The unit skips it.

MP3CD F01 albumF01

song01.mp3
song02.mp3 doc01.doc
song03.mp3 photo01.jpg
song04.mp3
song05.mp3

F02 albumF02

F04 albumF04
song06.mp3
song07.mp3 song13.mp3
song08.mp3 song14.mp3
song09.mp3
song10.mp3

F03 albumF03

song11.mp3
song12.mp3

Display selection

Track number Elapsed

The ID3-Tag is an information field for MP3. Music title, artist name and
album name can be stored into the tag. This unit shows these information.
Press the FM MODE/DISPLAY button on the main unit (or the DISPLAY
button on the remote control) during play.

- Each time the button is pressed, the display changes in the following
sequence.
Folder name (Album name)/File name (Music name)
Music information: music title
Music information: artist name
Music information: album name

- If no music information is stored, “NO INFO” appears. Press this but­ton again, the track number and elapsed playing time appear.

playing time

Folder selection

Example: There are 3 folders in MP3 CD.

- In stop mode, press the TUNER PRESET/FOLDER SELECT button
(or the PRESET/FOLDER SELECT button on the remote control)
repeatedly to select desired folder number. The folder number will
display in recycle:
1 v 2 v 3 v 1 v 2 v 3 v 1 v ...
When desired folder is selected, press the i button to start play
from the first track of this folder.

- In playing mode, do the same operation and the same folder display
order in turn. But when the last folder is in, other folders cannot be
selected in recycle order. Press the n button to go into stop mode.

- After selecting the desired folder in the playing mode, the unit will play
the first track in it.

-6-

LISTENING TO THE RADIO

Before use

When the unit is shipped from the factory, its AM frequency band is set as
“522 ~ 1611 kHz (in 9 kHz steps)”.
If your local AM broadcast system is organized in 10 kHz steps, change
the frequency band to “520 ~ 1610 kHz (in 10 kHz steps)” as follows.

1. Press the TUNER/BAND button to select AM.

2. Press the n and the RANDOM buttons on the main unit at the same
time, the frequency band will be changed to “520 ~ 1610 kHz (in 10
kHz steps)”.

Note:
To return the original setting, repeat the steps above.

Automatic/manual tuning

1. Press the TUNER/BAND button to select FM or AM.

2. Automatic tuning

- Press the f or e button for at least 1 second to tune in a

station. The unit will scan up or down the band and receive the
next receivable station. Press the button again to continue.

Manual tuning

- Press the f or e button briefly until the desired frequency is

displayed.

To receive FM stereo broadcasts

“STEREO” appears when an FM stereo broadcast is received under stereo
receiving mode.

- If the signal from an FM stereo station is weak and reception is poor,
“STEREO” blinks or disappears. Press the FM MODE/DISPLAY but­ton (or the FM MODE/REPEAT button on the remote control) to change
to the monaural mode. The reception may be improved, but the sound
will be monaural.

To preset stations

Up to 24 stations for FM band, 12 stations for AM band can be preset.

Automatic presetting (APT)

1. Press the TUNER/BAND button to select AM or FM.

2. Press the MEMORY button for at least 3 seconds, “PROGRAM” blinks.
The automatic tuning mode is set and automatic presetting begins
from the low end of the band.
When 24 FM or 12 AM stations have been preset or the high end of
the band is reached, automatic presetting stops, “PROGRAM” disap­pears and the station memorized on channel 1 will be heard.

Note:
If APT is activated, all previously programmed stations of the band will be
cleared and new stations will be programmed.

Manual presetting

1. Tune in the station to be preset as described above.

2. Press the MEMORY button. “PRO-
GRAM” appears and blinks.

3. While “PROGRAM” is blinking, press
the TUNER PRESET/FOLDER SE­LECT button on the main unit (or the
PRESET/FOLDER SELECT button
on the remote control) to select the
channel to be preset.

- The number buttons on the remote control can be used to preset

the station directly. Press two numbers, in this example, press 0,
then 9, then step 4 is omitted.

4. While “PROGRAM” is blinking, press
MEMORY button and “PROGRAM”
disappears.

- In this example, “103.25MHz” FM station is preset on FM channel

9.

5. Repeat steps above to add more preset stations.

- When presetting a new station, the previous preset station is

cleared.

Listening to preset stations

1. Press the TUNER/BAND button to select FM or AM.

2. Press the TUNER PRESET/FOLDER SELECT button on the main
unit (or the PRESET/FOLDER SELECT button on the remote control)
to select the desired channel number.

- The number buttons on the remote control can also be used. Press

two number buttons within 2 seconds.

When beat interference is heard

Beat (a high-pitched noise) may sometimes be heard during listening the
radio broadcasts. If this occurs,

1. Press the MEMORY button.

2. While “PROGRAM” is blinking, press the n button on the main unit to
select “bc-A” or “bc-B”. Select the setting that gives the best result.

LISTENING TO OTHER SOURCES

1. Press the FUNCTION button to select “LINE”. 2. Follow the instructions supplied with the other equipment.

-7-

TIMER OPERATION

Using the timer

Set the on and off times, and function to be used. Operation will start with
the selected function at the on time.
The power will be switched off at the off time.
The timer will function every day unless it is released.

Before Operation

Make absolutely sure that the clock is set to the correct time before set­ting the timer.

- Prepare the sources to be used.

- Adjust the tuner or band of radio if choose TUNER function.

- Place the disc in advance if choose CD function.

- Adjust the volume to the suitable level for listening.

Example: Waking up 7:30 every day, listening to the radio till 8:15.

1. Press the FUNCTION button to select the desired preset function and
set the desired volume level for timer operation.

2. Press the CLOCK/TIMER button for
at least 2 seconds, the previous timer
ON time appears and “ ” blinks.

3. Press the MEMORY button, the
“hour” and “ ” blink.

4. Turn the VOLUME control to set the
“hour”.

10. Press the z/ON button to switch off
the power.

“ ”remains light.

Note:

- When the timer on time arrives, the power turns on and start the pre­set function.

- “ ” blinks while the timer operation is engaged.

- The timer will be set to the standby mode if press the z/ON button
when the timer in operating.

To check the timer settings

Turn on the power. Press the CLOCK/TIMER button once, current time
appears. Then press the CLOCK/TIMER button about 3 seconds, timer
on time appears, then press the button repeatedly, the timer setting are
displayed in the following order.

• Timer off time.

• Original preset function.

• Original display returns.

To change the timer settings

1. Press the CLOCK/TIMER button to select the setting to be changed.

2. Press the MEMORY button so that the display blinks.

3. Change the setting as explained above.

To release the timer

Press the CLOCK/TIMER button repeatedly till “ ” display disappears.

To set the timer again with the same settings

1. Press the CLOCK/TIMER button repeatedly to display “ ”.

2. Press the z/ON button to switch off the power.

5. Press the MEMORY button, the
“minute” blinks.

6. Turn the VOLUME control to set the
“minute”.

7. Press the MEMORY button to con­firm the “minute” and finish ON time
setting. “ ” and “hour” appear
and blink.

8. Repeat steps 4 - 7 above. This completes the setting of the time off
timer.

9. Press the MEMORY button, the origi­nal display and “ ” appear.

MAINTENANCE

USING THE SLEEP TIMER
(Remote control only)

The sleep timer automatically switches off the power after a preset time
has elapsed. There are 12 time periods available: 120, 110, 100, 90, 80,
70, 60, 50, 40, 30, 20, and 10 minutes. Press the SLEEP button repeat­edly to select a time period.

Example: Select the sleep time of 60 minutes.
Press the SLEEP button to choose sleep time of 60 minutes, “SLEEP”
and the sleep time of 60 will blink, after several seconds the original display
returns, “SLEEP” remains blink till power off.

- If you want to examine the remain sleep time during sleep timer op­eration, press SLEEP button once, the remain time will display.

- To release the sleep timer, press the SLEEP button repeatedly till
“SLEEP” disappears.

- The sleep timer will clear automatically when the power turned off.

Cleaning the unit

Clean the outside of the unit with a clean soft cloth, moistened with luke­warm water. Do not use benzene, thinner or alcohol since they will mar
the finish of the surfaces.

-8-

SPECIFICATIONS

CD player

Type:

2-channel stereo

Pick-up:

Optical 3-beam semiconductor laser

Laser output:

0.6mW (Maximum continuous wave)

Wave length:

790nm

Wow/flutter:

Below measurable limits

Tuner

Reception frequency:

FM: 87.5 ~ 108.0MHz
AM: 522 ~ 1611kHz (9kHz steps)
520 ~ 1610kHz (10kHz steps)

General

Output Power:

40 W X 2 (at 6 ohms, 10% distortion)

Input:

LINE IN: 900mV/50KΩ

Outputs:

SPEAKER: 6 ohms
PHONES: 8 ~ 32 ohms

Power requirement:

AC 230V, 50Hz

Power consumption:

70 W

Dimensions:

165(W) x 205(H) x 305(D) mm

Weight:

4.5kg

Speaker systems

Type:

Bass reflex

Unit used:

Woofer: 12 cm cone type
Tweeter: 2.5 cm balanced driver

Maximum power-handling capacity:

80W (peak)

Nominal impedance:

6 ohms

Dimensions:

154(W) x 208(H) x 192(D) mm

Weight:

1.8kg (per speaker)

Specifications subject to change without notice.

-9-

GUARANTEE TO CUSTOMER

Sanyo Europe Ltd. (the Company) guarantees to the initial retail
purchaser that if this equipment is or becomes defective and that,
in the opinion of the Company, the defect is due to faulty material
or workmanship the Company will, for a period of 12 calendar
months from the date of sale to the original purchaser repair or
replace, at its sole option, free of charge, any such defective
component part of the equipment, always provided that: -

1. The equipment has at all times been used in accordance with
the operating instructions issued by the Company, and has not
been connected to an electrical mains supply for which it has not
been adjusted.

2. Accidental damage, or damage caused by negligence or
misuse by the user, including leakage from exhausted batteries, is
specifically excluded.

3. Unauthorised repairs, or any modification to the equipment
which has not been expressly approved by the Company, shall
render this guarantee null and void.

4. Failure due to fair wear and tear of any item, such as batteries,
record playing styli, and tape recording, playback and erase heads
is specifically excluded.

Thank you for buying Sanyo. This equipment should give you
many years of pleasure and faithful service but in the event that a
fault occurs, the following notes for your guidance may be helpful:-

1. PLEASE RETAIN YOUR PURCHASE RECEIPT WHICH WILL
BE REQUIRED FOR SERVICE DURING GUARANTEE.

2. If your Sanyo equipment proves faulty during the period of
guarantee, take it or send it back to the dealer who originally
supplied it together with this guarantee and the proof of purchase.
We have made arrangements with our approved dealers under
which they will carry out in-guarantee service repairs on our behalf.
In this way, we hope to reduce to a minimum the amount of time
you will be without your equipment.

3. If for some reason it is impossible to return the equipment to the
original supplies, please contact our Consumer Relations Depart­ment at the address below for further advice.

4. Should the equipment require servicing after the expiry of the
guarantee period, take or send it to the original supplier or any
other Sanyo dealer. He will be pleased to give you a quotation for
the repair. If you are in any doubt about what to do, write to us at
the address below or telephone:

This guarantee is not transferable and is only applicable within the
United Kingdom (and the Republic of Ireland). Nothing in this
express guarantee affects the statutory rights available to the
purchaser of this equipment.
Note: This guarantee supersedes any other form of guarantee
that may inadvertently have been enclosed with or attached to the
product. (August 1978).

Consumer Relations Department,
Sanyo Europe Ltd.,
18 Colonial Way,Watford
WD24 4PT
Tel: Watford 246363

R6

(UK) 1AD6P1P2087-BA

SANYO Electric Co., Ltd.