Thank you for choosing this product. This
manual will guide you for the proper
operation of your TV. Before operating
the TV, please read this manual
thoroughly.
Please do keep this manual in a safe
place for future references.
Preparation
For ventilation, leave a free space of at least
10 cm all around the set. To prevent any fault
and unsafe situations, please do not place any
objects on top of the set.
Use this device in moderate climates.
10 cm
10 cm
10 cm
Safety Precautions
Please read the following recommended
safety precautions carefully for your
safety.
Power Source
The TV set should be operated only from a
220-240 V AC, 50 Hz outlet. Ensure that you
select the correct voltage setting for your
convenience.
Power Cord
Do not place the set, a piece of furniture, etc.
on the power cord (mains lead) or pinch the
cord. Handle the power cord by the plug. Do
not unplug the appliance by pulling from the
power cord and never touch the power cord with
wet hands as this could cause a short circuit or
electric shock. Never make a knot in the cord or
tie it with other cords. The power cords should
be placed in such a way that they are not likely
to be stepped on. A damaged power cord can
cause fi re or give you an electric shock. When it
is damaged and needs to be replaced, it should
be done by qualifi ed personnel.
English - 4 -
Moisture and Water
Do not use this device in a
humid and damp place (avoid
the bathroom, the sink in the
kitchen, and near the washing
machine). Do not expose this
device to rain or water, as this
may be dangerous and do
not place objects fi lled with
liquids, such as fl ower vases,
on top. Avoid from dripping
or splashing.
If any solid object or liquid falls into the cabinet,
unplug the TV and have it checked by qualifi ed
personnel before operating it any further.
Cleaning
Before cleaning, unplug the TV
set from the wall outlet. Do not
use liquid or aerosol cleaners.
Use soft and dry cloth.
Ventilation
The slots and openings on
the TV set are intended for
ventilation and to ensure reliable operation. To
prevent overheating, these openings must not
be blocked or covered in anyway.
Heat and Flames
The set should not be placed
near to open flames and
sources of intense heat such
as an electric heater. Ensure
that no open fl ame sources,
such as lighted candles,
are placed on top of the TV.
Batteries should not be exposed to excessive
heat such as sunshine, fi re or the like.
Lightning
In case of storm and lightning
or when going on holiday,
disconnect the power cord
from the wall outlet.
Replacement Parts
When replacement parts are required, make
sure that the service technician has used
replacement parts, which are specifi ed by the
manufacturer or have the same specifi cations as
the original one. Unauthorized substitutions may
result in fi re, electrical shock or other hazards.
Servicing
Please refer all servicing to
qualifi ed personnel. Do not
remove the cover yourself as
this may result in an electric
shock.
Waste Disposal
Instructions for waste disposal:
• Packaging and packaging aids are recyclable
and should principally be recycled. Packaging
materials, such as foil bag, must be kept away
from children.
• Batteries, including those which are heavy
metal-free, should not be disposed of with
household waste. Please dispose of used
battery in an environment friendly manner.
Find out about the legal regulations which
apply in your area.
• Cold cathode fluorescent lamp in LCD
PANEL contains a small amount of mercury;
please follow the local laws or regulations for
disposal.
FOR EU USERS
The symbol mark and recycling
systems described below
apply to EU countries and do
not apply to countries in other
areas of the world.
Your SANYO product is
designed and manufactured
with high quality materials and components
which can be recycled and/or reused.
The symbol mark means that electrical
and electronic equipment, batteries and
accumulators, at their end-of-life, should be
disposed of separately from your household
waste.
Note:
If a chemical symbol is printed beneath the
symbol mark, this chemical symbol means that
the battery or accumulator contains a heavy
metal at a certain concentration. This will be
indicated as follows: Hg: mercury, Cd: cadmium,
Pb: lead
In the European Union there are separate
collection systems for used electrical
and electronic equipment, batteries and
accumulators.
Please, dispose of them correctly at your local
community waste collection/recycling centre.
Please, help us to conserve the environment
we live in!
Disconnecting the Device
The mains plug is used to disconnect TV set
from the mains and therefore it must remain
readily operable.
Headphone Volume
Excessive sound pressure from
earphones and headphones
can cause hearing loss.
Installation
To prevent injury, this device
must be securely attached to the wall in
accordance with the installation instructions
when mounted to the wall (if the option is
available).
LCD Screen
The LCD panel is a very high technology product
with about a million thin fi lm transistors, giving
you fi ne picture details. Occasionally, a few
non-active pixels may appear on the screen
as a fi xed blue, green or red point. Please note
that this does not affect the performance of
your product.
Warning
Do not leave your TV in standby or operating
mode when you leave your house.
• This television is designed to consume less energy to save environment.
You not only help to save the environment but also you can save money by reducing electricity
bills thanks to the energy effi ciency feauture of this TV. To reduce energy consumption, you should
take the following steps:
• You can use Power Save Mode setting, located in the Feature menu. If you set Power Save
Mode as On, the TV will switch to energy-saving mode and luminance level of TV set will be
decreased to optimum level. Note that some picture settings will be unavailable to be changed
when the TV is in Power Save Mode.
• When the TV is not in use, please switch off or disconnect the TV from the mains plug. This will
also reduce energy consumption.
• Disconnect power when going away for longer time.
• Note that annually,using the TV set in Power Save Mode has more power effi ciency than
disconnecting the TV from the mains plug instead of keeping stand-by mode. Therefore it is highly
recommended to activate Power Save Mode setting to reduce your annual power consumption.
And also it is recommended to disconnect the TV from the mains plug to save energy more
when you do not use.
• Please helps us to save environment by following these steps.
Repair Information
Please refer all servicing to qualifi ed personnel. Only qualifi ed personnel must repair the TV. Please
contact your local dealer, where you have purchased this TV for further information.
Mono/Stereo - Dual I-II / Current language 1.
(in DTV mode) (*)
Expand (in TXT mode) / Image size2.
Electronic programme guide (in DTV 3.
mode)
Favourite Mode Selection (*) (in DTV 4.
mode)
Red (Sound Menu) / Channel List (*) (in 5.
DTV mode)
Green / Picture Menu / Subtitle on-off (*) 6.
(in DTV mode)
Direct Programme7.
Teletext / Mix / Pat mode (in TXT mode) 8.
Volume Down9.
Programme Down / Page up (in DTV 10.
mode)
Mute11.
Navigation Buttons12.
Exit (in DTV mode)/ Index Page (in TXT 13.
mode)
Menu14.
Info/ Reveal (in TXT mode)15.
Okay (Store) / Select / Hold (in TXT mode)16.
External Source17.
Programme Up / Page down (in DTV 18.
mode)
Volume Up19.
Programme Previous20.
Yellow / Feature Menu / Currrent 21.
Language (*) (in DTV mode)
Blue (Install Menu) / Favourite Mode 22.
Selection (*) (in DTV mode)
Picture Mode Selection23.
Sleep Timer 24.
Pip/Pap mode25.
Subtitle on-off / TXT Subtitle26.
Standby27.
(*) available for EU countries.
27
26
1
2
3
SCREEN
EPG
LANG
SUBTTL
PIP
FAV
SLEEP
PRESETS
4
5
6
25
24
23
22
21
7
8
9
10
11
P
P
SOURCE
20
19
18
17
16
RETURN
OK
MENU
INFO/?
15
12
13
14
You can use numeric buttons on the remote control
to input letters when necessary. Pressing the numeric
buttons ‘0...9’ inputs letters assigned to that button.
Letters are present one by one as the button is
pressed. Table below shows the assigned letters:
1. S/PDIF Digital Out outputs digital audio signals of the currently watched source.
Use a digital optic cable to transfer audio signals to a device that has S/PDIF input.
2. Subwoofer Out is for connecting an external, active subwoofer to the set to give a much
deeper bass effect.
Use an appropriate RCA cable to connect the set to a subwoofer unit.
Audio Line Outs 3. output audio signals to an external device such as an optional sound
system.
To connect the external speakers to your TV, use AUDIO LINE OUTS of the TV with an
audio cable.
4. SCART 2 inputs or outputs for external devices.
5. SCART 1 inputs or outputs for external devices.
Connect the SCART cable between SCART sockets on TV and SCART socket on your
external device (such as a decoder, a VCR or a DVD player).
Note: If an external device is connected via the SCART sockets, the TV will automatically switch to AV mode.
If both sockets are employed at the same time, SCART 1 will override SCART 2 unless manually selected. Note: You should connect the decoder to EXT-1, if you are planning to watch a scrambled channel.
The decoder might not function properly if you do not connect the decoder to the Scart 1 (Ext-1) socket.
Note: Picture state can be affected by scart cable quality.
6. Component Video Inputs (YPbPr) are used for connecting component video.
You can connect the component video and audio sockets with a device that has component
output. Connect the component video cables between the COMPONENT VIDEO INPUTS
on on the TV and the component video outputs of your device. While connecting, be sure
that the letters on your TV, “ Y ”, “ Pb ”, “ Pr ” correspond with your device’s connectors.
7. PC/YPbPr Audio Inputs are used for connecting audio signals of a PC or a device that
connects to the TV via YPbPr.
Connect the PC audio cable between the AUDIO INPUTS on the TV and audio output of
your PC to enable PC audio.
Connect the audio cable between AUDIO INPUTS on the TV and audio outputs of your
device to enable component audio.
8. S/PDIF Coaxial Out outputs digital audio signals of the currently watched source.
Use an SPDIF coaxial cable to trasfer audio signals to a device that has S/PDIF input.
9. RF Input connects to an antenna or a cable.
Note that if you use a decoder or a media recorder, you should connect the aerial cable
through the device to the television with an appropriate antenna cable, as shown in the
illustrationin the following pages.
10. PC Input is for connecting a personal computer to the TV set.
Connect the PC cable between the PC INPUT on the TV and the PC output on your PC.
11. HDMI 2: HDMI Input
HDMI 1: 12. HDMI Input
HDMI Inputs are for connecting a device that has an HDMI socket. Your LCD Television is
capable of displaying High Defi nition pictures from devices such as a High Defi nition Satellite
Receiver or DVD Player. These devices must be connected via the HDMI sockets or Component
Socket. These sockets can accept either 720p or 1080i signals. No sound connection is needed
for an HDMI to HDMI connection.
CI Slot is used for inserting a CI card. A CI card allows you 1.
to view all the channels that you subscribe to. For more
information, see “Conditional Access” section.
Side USB input . 2.
Note: Codec update cannot be performed.
Headphone jack is used for connecting an external 3.
headphone to the system. Connect to the HEADPHONE
jack to listen to the TV from headphones (optional).
Video Input is used for connecting video signals of 4.
external devices.Connect the video cable between the
VIDEO IN socket on the TV and the VIDEO OUT jack on
your device.
Audio Inputs are used for connecting audio signals of 5.
external devices. Connect the audio cable between the
AUDIO INPUTS on the TV and the AUDIO OUTPUT jacks
on your device. Note: If you connect a device to the TV via
the VIDEO INPUT, you should also connect your device
with an audio cable to the AUDIO INPUTS of the TV to
enable audio.
Standby switch is used for turning the TV on or off6. .
• You can connect USB devices to your TV by using the USB input of the TV. This feature allows
you to display/play JPG and MP3 fi les stored in a USB stick.
• It is possible that certain types of USB devices (e.g. MP3 Players) may not be compatible with
this TV.
• You may back up your fi les before making any connections to the TV set in order to avoid any
possible data loss. Note that manufacturer will not be responsible for any fi le damage or data
loss.
• Do not pull out USB module while playing a fi le.
CAUTION: Quickly plugging and unplugging USB devices, is a very hazardous operation.
Especially, do not repeatedly quickly plug and unplug the drive. This may cause physical
damage to the USB player and especially the USB device itself .
SIDE VIEW USB MEMORY
USB Memory Connection
• Plug your USB device to the USB input of the TV.
Note: USB hard disk drives are not supported.
• It is recommended that you connect your USB device directly to the USB input of the TV. Some
compatibility problems may occur if you use a separate cable connection.
If you want to connect a DVD player to your LCD TV, you can use connectors of the TV set. DVD
players may have different connectors. Please refer to your DVD player’s instruction book for
additional information. Power off both the TV and the device before making any connections.
Note: Cables shown in the illustration are not supplied.
• If your DVD player has an HDMI socket, you can connect via HDMI. When you connect to DVD
player as illustrated below, switch to HDMI source. See, “Input Selection” section.
• Most DVD players are connected through COMPONENT SOCKETS. Use a component video
cable to connect video input. For enabling audio, use a component audio cable as illustrated
below. When the connection is made, switch to YPbPr source. See, “Input selection” section.
• You may also connect through the SCART 1 or SCART 2. Use a SCART cable as shown
below.
Note : These three methods of connection perform the same function but in different levels of quality. It is not
necessary to connect by all three methods.
You can connect a range of optional equipment to your LCD TV. Possible connections are shown
below. Note that cables shown in the illustration are not supplied.
• For connecting a camcorder, connect to the VIDEO IN socket and the AUDIO SOCKETS. For
selecting the related source, see the section “Input selection” in the following parts.
• To listen the TV sound from headphones, connect to the HEADPHONE jack of theTV.