Sangean HDR-1 User Manual

User Manual

HDR-1

HD Radio™ Technology Manufactured Under License From iBiquity Digital Corporation. iBiquity Digital and the HD Radio and HD logos are registered trademarks of iBiquity Digital Corporation. HD Radio

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:194

is a trade mark of iBiquity Digital Corporation. U.S. a nd Foreign Patents.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block a ny ventilation openings. In stall in accordance with the manufa cturer’s in structions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

10. Only use attachments/accessories specified by the manufacturer.

11. Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combin ation to avoid injury from tip-over.

12. Unplug this apparatus during lightning storms or when unused for long periods of time.

13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

14. To reduce the Risk of Fire or Electric Shock. Do not expose this appliance to rain or moisture.

15. The Shock Hazard marking and Associated Graphical Symbol is provided on the rear panel of unit.

16. Apparatus shall not be exposed to dri pping or splashing and no objects filled with liquids, shall not be placed on the apparatus.

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:195

Unit Controls

(Front)

1.2.LCD display Standby LED indicator

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:196

Remote Control Sensor

3. Power and Control knob

Unit Controls

(Rear)

FM Telescopic Antenna

AC power cord socket

Music and News selection switch

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:207

Headphone socket

Aux In socket

10.

External AM Loop antenna socket

Remote Control

Power

Information button

ATS a nd Setup button

Band selection

Mute button

Number buttons

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:208

Audio Equalizer selection

7. Last station recall

8. HD Radio Seek button

9. Tuning Control

10. Volume Control

11. Execution button

12.

Accessorie s

Detachable power Cord x 1

FM Dipole Antenna x 1

AM Loop antenna x 1

Remote control unit x 1

Instruction manual x 1

Warra nty card x 1

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:209

Getting started

First find a location for your new HD radio,

1. The FM telescopic antenna is alrea dy in stalled. Dipole Antenna and installing tool are in cluded for better reseption.

2. Connect the AM loop antenna into external AM loop a ntenna termin al on the back of the unit.

3. Plug the AC power cord into the socket located on the back of the unit. Please ensure that the plug is pushed fully into the socket.

Setting the clock

Clock setting can be done when the receiver is on or in Standby Mode (power off).

1. Press “Enter” or “Power /Control knob” button. The display should not read “Setup Clock Set”.

2. Press “Enter” or “Power /Control knob” button again. Display should read “Clock Set” and the hour should begin blinking.

3. Press “Tuning” Up/Down or rotate “Power /Control knob” to select Hour then press “Enter” or “Power /Control knob” button again to complete hour setting.

4. Use same procedures to complete minute, AM or PM, date, month and year. Press “Enter” or “Power /Control knob” button to complete Clock Set.

4. Plug the other hand of the AC power cord into a wall socket and switch on the wall socket if needed. (NOTE: You may hear a loud “POP” when power is connected. Do not be alarmed.)

Important:

1. The AM loop antenna should be located at least 50 cm away from the receiver to avoid possible interference.

2. Do not touch Power/Control knob on the radio while plug in AC power.

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:2010

Radio Controls

Selecting the radio band/Auxiliary Input

1. To turn the radio on press the “Power” button on the remote control or hold “Power /Control knob” on the unit for 2 seconds.

2. To turn the radio off press the “Power” button on the remote control or hold “Power /Control knob” on the unit for 2 seconds. (NOTE: In standby mode, the tuner will display the time, dim the backlight (in 12 seconds) and standby LED will be on.

3. To access or select the menu option press and release the Power/ Control knob on the unit or “Enter” button on the remote.

4. To navigate through the menu options rotate the “Power/Control knob” or press “Tuning” Up/Down button.

5. During normal operation (not in the menu tree) the “Power/Control knob” will control volume.

Manual Tuning

Using Remote:

1. Press the Tuning rocker switch UP or DOWN on the remote control to select a radio station. Tuning step per press for AM is 10 kHz and 100 kHz for FM band.

Using the Unit:

1. Press “Power/Control knob” and cycle through the menu options by rotating the “Power/Control knob” until you are at “Tune” menu option.

2. Press “Power/Control knob to select.

3. Rotate “Power/Control knob” until you reach desired station frequency.

Using the remote, press the “BAND” button. (Note: When you switch from one band to another, the radio will return to the last tuned station used in the band.)

Using the Unit:

1. Press “Power/Control knob” and cycle through the menu options by rotating the “Power/Control knob” until you are at “Band” menu option.

2. Press “Power/Control knob to select. Repeat until desired band is reached.

Note: When AUX IN socket behind the unit is connected, Display will cycle through AM FM AUX IN AM …………

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:2011

Volume Control

Using the Remote:

1. Press “Volume” Up/Down button until you reach desired volume. Using the Unit:

1. Rotate the “Power/Control knob” unit desired volume is reached.

Mute

Using the Remote:

1. Press MUTE button on the remote control to mute the radio. Press the MUTE button again to turn on the volume.

Using the Unit:

1. Rotate “Power/Control knob” until volume is muted.

Audio Equalizer (EQ)

Using the Remote:

1. Press the “EQ” button until desired EQ setting is reached. Using the Unit:

1. Press “Power/Control knob” and cycle through the menu options by rotating the “Power/Control knob” until you are at “EQ” menu option.

2. Press “Power/Control knob” to select.

3. Rotate “Power/Control knob” until you reach desired preset EQ option.

Custom “BASS” and “TREBLE” Settings

Using the Remote:

1. Press “EQ” button until “Bass” or “Treble” options are chosen.

2. Press “Enter” button to select.

3. Press “Tuning” Up/Down button until desired level is reached.

4. Press “Enter” button to save setting.

5. Repeat as necessary.

Using the Unit:

1. Press “Power/Control knob” and cycle through the menu options by rotating the “Power/Control knob” until you are at “EQ” menu option.

2. Press “Power/Control knob” to select.

3. Rotate “Power/Control knob” until you reach “Bass” or “Treble” EQ option.

4. Press “Power/Control knob” to select.

5. Rotate “Power/Control knob” until desired levels are reached.

6. Press “Power/Control knob” to select settings.

7. Repeat as necessary.

Music/News selection switch

Music/News selection switch is located on the back of the unit. Switch Music/News selection to Music position when you wish to use “EQ” settings. Switch it to News position when you listen to news programs. Note: The EQ setting can’t be used when the Music/News selection is in News position.

HD SEEK function

Using the Remote:

1. Press the “HD SEEK” Up/Down button to seek the next frequency broadcasting in a usable HD Radio signal.

Using the Unit:

1. Press “Power/Control knob” and cycle through the menu options by rotating the “Power/Control knob” until you are at “HD SEEK” menu option.

2. Press “Power/Control knob” to select.

3. Rotate “Power/Control knob” to select “Up” or “Down” direction.

4. Press “Power/Control knob” to select.

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:2012

Listening to HD Radio

When HD Radio station is found, display will show,

1. Station call sign.

2. The number of the multicasting program (1= main program).

3. The total number of HD Radio program services and HD Radio mark.

4. The preset number of this program.

5. The radio band.

Receiving & Tuning Multicast Stations

When the radio is tuned to an HD compatible station and it determines that one or more Multicast station are available the station call letter will be followed by a number designator indicating the number of available Multicast stations.

Using the Remote:

1. Press “Tuning” Up/Down button to navigate through the multicast stations.

Using the Unit:

1. Press “Power/Control knob” and cycle through the menu options by rotating the “Power/Control knob” until you are at “Tune” menu option.

2. Press “Power/Control knob” to select.

3. Rotate “Power/Control knob” to navigate to the next multicast signal. NOTE:

When navigating to a different frequency, wait for the HD signal to lock before navigating through the additional multicast signals. The lock will be achieved when the HD signal is no longer blinking and the station call letters will have a number following it, i.e. KROQ-1 2 HD FM.

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:2013

Display Modes (INFO)

There are several display modes. Please refer to the HDR-1 Menu Structure Table for a complete listing and description of these display modes.

Using the Remote:

1. Press “Info” button.

2. Continually press “Info” button or press “Tune” Up/Down button to navigate through available display modes.

Using the Unit:

1. Press “Power/Control knob” and cycle through the menu options by rotating the “Power/Control knob” until you are at “Info” menu option.

2. Press “Power/Control knob” to select.

3. Rotate “Power/Control knob” to navigate through the available display modes.

4. Press “Power/Control knob” to select display mode.

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:2014

Advanced Information

There are several Advanced Display modes. Please refer to the HDR-1 Menu Structure Table for a complete listing and description of these display modes.

Using the Remote:

1. Press and hold “Info” button.

2. Continually press “Info” button to navigate through available display modes.

Using the Unit:

1. Press “Power/Control knob” and cycle through the menu options by rotating the “Power/Control knob” until you are at “Ad. Info” menu option.

2. Press “Power/Control knob” to select.

3. Rotate “Power/Control knob” to navigate through the available display modes.

4. Press “Power/Control knob” to select display mode.

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:2015

Hybrid Seek

Using the Remote:

1. Press the “SEEK” Up/Down button to seek the next frequency broadcasting in a usable radio signal.

Using the Unit:

1. Press “Power/Control knob” and cycle through the menu options by rotating the “Power/Control knob” until you are at “SEEK” menu option.

2. Press “Power/Control knob” to select.

3. Rotate “Power/Control knob” to select “Up” or “Down” direction.

4. Press “Power/Control knob” to select.

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:2016

ATS – Auto Tuning System

The ATS function will scan through the selected band frequency for all usable signals. It will create an easily navigated table for all detected signals.

Using the Remote:

1. Press and hold “ATS” button to activate menu.

2. Press “Enter” button to activate frequency scanning.

3. Allow radio to finish scanning. Once completed you can navigate through the available stations using the “Tune” Up/Down buttons. To navigate to the multicast stations using ATS function press the “Enter” button.

4. To recall ATS table navigation press “ATS” button. Using the Unit:

1. Press “Power/Control knob” and cycle through the menu options by rotating the “Power/Control knob” until you are at “SETUP” menu option.

2. Press “Power/Control knob” to select.

3. Rotate “Power/Control knob” to cycle through the menu options until you reach the “ATS SCAN” menu option.

4. Press “Power/Control knob” to select.

5. Allow radio to finish scanning. Once completed you can navigate through the available stations by rotating the “Power/Control knob”. To navigate to the multicast stations using ATS function press the “Enter” button.

6. To recall the ATS Table press “Power/Control knob” and cycle through the menu options until you reach the “ATS Table’ menu option.

7. Press “Power/Control knob” to select.

8. You can begin navigating as described above. NOTE:

While using the ATS Table, the “Power/Control knob” will no longer control volume. You must wait until the unit returns to normal control function, indicated by displaying the previously selected display mode.

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:2017

Setting and Recalling Memory Presets

Preset stations

There are 10 preset stations each for AM and FM.

Setting Memory Presets

Using the Remote:

1. Press “Band” button to select desired band.

2. Hold corresponding numbered button for 2 seconds to store. i.e. to store 93.1 into memory position 2 press and hold the “#2” button on the remote.

Using the Unit:

1. Press “Power/Control knob” and cycle through the menu options by rotating the “Power/Control knob” until you are at “SET PRESET” menu option.

2. Press “Power/Control knob” to select.

3. Rotate “Power/Control knob” to cycle through the preset options until you reach the desired location.

4. Press “Power/Control knob” to select.

Recalling Memory Presets

Using the Remote:

1. Press corresponding numbered button to the memory location. i.e. to recall 93.1 stored in preset number 2 press and release the “#2” button.

Using the Unit

1. Press “Power/Control knob” and cycle through the menu options by rotating the “Power/Control knob” until you are at “GO-TO PRESET” menu option.

2. Press “Power/Control knob” to select.

3. Rotate “Power/Control knob” to cycle through the preset options until you reach the desired location.

4. Press “Power/Control knob” to select. Note:

If preset stations are full, display will appear Preset Full. Press another 2 seconds will replace previous memory station. Display will show “P-X stored”. To give up the preset, simply release the number button when Preset Full appears, display will return to frequency status.

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:2018

Last Recall Station

Using Remote:

1. Press LAST RECALL button on the remote control to recall last listening station.

Using the Unit:

1. Press “Power/Control knob” and cycle through the menu options by rotating the “Power/Control knob” until you are at “RECALL” menu option.

2. Press “Power/Control knob” to select.

Setting Sleep timer

This unit comes with an adjustable sleep timer. This function can only be activated when the unit is on. Using the Remote:

1. Press and hold “ATS/Setup” button to activate menu.

2. Continue to press “ATS” button or “Tune” Up/Down button to reach “SLEEP” menu option.

3. Press “Enter” to select.

4. Press “Tune” Up/Down button to set the desired sleep time. Using the Unit:

1. Press “Power/Control knob” and cycle through the menu options by rotating the “Power/Control knob” until you are at “SETUP” menu option.

2. Press “Power/Control knob” to select.

3. Rotate the “Power/Control knob” until you are at “SLEEP” menu option.

4. Press “Power/Control knob” to select.

5. Rotate the “Power/Control knob” to set desired sleep time.

6. Press “Power/Control knob” to save setting.

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:2019

Auto clock function

If the FM station you are listening to providing RDS service and has Auto clock time setting feature ( CT ). You can set the clock to be Auto clock, the clock will be automatically adjusted by the station RDS – CT service.

Note: Before you set the Auto clock function, please make sure the FM station you tune to providing auto clock time setting service.

The Auto clock function can be set only when radio Power is on.

1. Press ATS/SET UP button for more than 2 seconds until display appears SET UP and flashing ATS.

2. Press and release ATS/SET UP button to get AUTO CLOCK.

3. Press and release Execution button to confirm AUTO CLOCK setting.

4. The clock time will be auto setting by the FM RDS station which supports Auto Clock setting ( CT ).

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:2020

Turning Alarms On/Off & Setting

This unit features a dual alarm system that can sound either to a beeping tone or AM/FM or Auxiliary Audio. The easiest way to set the alarms is when the unit is off, and these instructions are designed using this option. Using the Remote:

1. Press and hold “ATS/Setup” button to activate menu.

2. Continue to press “ATS” button or “Tune” Up/Down button to reach desired alarm (Alarm-1 or Alarm-2).

3. Press “Enter” to select.

4. Press “Tune” Up/Down button to set the desired alarm setting (Beep, AM, FM, Auxiliary, OFF).

5. If turning the alarm off, then press “Enter” button to save. Any other setting, continue to next step.

6. Set appropriate time. Hour first, then Minutes, AM/PM then to frequency options (Daily, Weekdays, Once, Weekends.)

7. Press “Enter” to save selections and proceed to next step.

8. If using Beep Function proceed to step 13.

9. If using AM set the appropriate frequency and continue to step 12.

10. If using FM, set the appropriate frequency and multicast channel and continue to step 12.

11. If using Auxiliary continue to next step.

12. Set desired volume level.

13. Press “Enter” to save settings.

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:2021

Using the Unit:

1. Press “Power/Control knob” and cycle through the menu options by rotating the “Power/Control knob” until you are at desired alarm (Alarm-1 or Alarm 2).

2. Press “Power/Control knob” to select.

3. Rotate “Power/Control knob” to select the desired alarm setting (Beep, AM, FM, Auxiliary, OFF).

4. If turning off, press “Power/Control knob” to save. For all others press “Power/Control knob” and proceed to next step.

5. Set appropriate time. Hour first, then Minutes, AM/PM then to frequency options (Daily, Weekdays, Once, Weekends.)

6. Press “Power/Control knob” to save selections and proceed to next step.

7. If using Beep Function proceed to step 12.

8. If using AM set the appropriate frequency and continue to step 12.

9. If using FM, set the appropriate frequency and multicast channel and continue to step 12.

10. If using Auxiliary continue to next step.

11. Set desired volume level.

12. Press “Power/Control knob” to save settings.

Note: Daily – wake up at set alarm time everyday. Weekdays – wake up only on Monday to Friday at set alarm time. Weekends – wake up only on Saturday and Sunday at set alarm time. Once – wake up only once at set alarm time.

Note: Make sure to set correct clock time and date before setting alarm timer. The radio can judge which dates are weekends and weekdays only when the clock and dates are set correctly before alarm setting.

Note: If you select alarm timer via “Beep” a repeating beep tone will sound. The alarm beep will increase in volume for 1 minute followed by 1 minute of silence before repeating the cycle (HWS-Humane Wake System). The HWS alarm will sound for 30 minutes unless turned off by pressing Power/Standby button.

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:2022

Snooze function

Canceling alarms

The alarm will sound at the selected alarm time. Press any button except Power (Standby) button can be silence for 5 minutes interval until alarm is on again (Snooze). This sequence can be repeated during the alarm period.

Display will appear Snooze and remaining time to next alarm on. Press Power button to cancel the Snooze.

Display backlight brightness control

1. Long press ATS/SET UP button until display appears SET UP and flashing ATS.

2. Repeatedly press and release ATS/SET UP button to get Backlight.

3. Press Execution button to enter backlight control mode.

4. Press Tuning Up or Down button to adjust display brightness.

5. Press Execution button again to complete setting.

The alarm will activate for 60 minutes (30 minutes for Beep alarm) until you press Power button to cancel it.

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:2023

Change Hour format

You can change 12 hours time format into 24 hours format and vice versa.

1. Long press ATS/SET UP button until display appears SET UP and flashing ATS.

2. Repeatedly press and release ATS/SET UP button to get Hour Mode.

3. Press Execution button to enter Hour mode adjustment.

4. Press Tuning Up or Down button to get change required hour format.

5. Press Execution button again to complete setting.

System RESET

System RESET feature will allow you to back to initial factory setting status of the radio.

1. Long press ATS/SET UP button until display appears SET UP and flashing ATS.

2. Repeatedly press and release ATS/SET UP button to get System Reset.

3. Press Execution button to execute system reset.

4. After the reset, the radio will clean all the memory/time/alarm etc. presets and back to initial factory setting status.

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:2024

RESET the radio

Specifications

If the radio fails to operate correctly i.e. display can’t change according to the operation. Unplug the AC power cord and wait for 5 seconds then re-plug. This is to reset the radio for troubleshooting the possible CPU power down. After RESET the radio, radio will be back to Standby mode (Power off)

Headphone socket

A 3.5 mm Headphone Socket located on the rear of the radio is provided for use with either headphones or an earpiece. Inserting a plug automatically mutes the internal speaker.

Aux in socket

1. Connect a stereo or mono audio source (i.e. iPod, MP3 or CD player) to the Aux IN socket on the rear of the radio.

2. Switch the band to AUX IN.

3. Select required volume level by pressing Volume Control on the remote control or rotary the Power/Control knob on the radio.

4. Select required audio equalizer by pressing EQ button.

Power Requirement:

Mains AC 120 volts 60 Hz only Battery (remote control) 3.0V CR 2025 button type

Frequency Coverage:

87.50 – 108 MHz

520 – 1710 kHz

HD FM

87.50 – 108 MHz

HD AM

520 – 1710 kHz

Circuit Features:

Loudspeaker Output Power Headphone socket Aux In socket

Aerial System:

FM Telescopic aerial AM Loop antenna

Dimensions (WxHxD): 290x110x182 mm Weight: approx. 3 kgs.

63 mm x 2 5 Watts x 2

3.5 mm dia.

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:2025

Brief User Interface:

Button

any keys

Standby Power OFF

Rotary Knob

Band

ATS

Info

action click click

click

click long 2s left right click click

long 2s

click

long 2s

status Alarm ON Standby / Power ON Alarm ON / Snooze ON Standby

Power ON Power ON Power ON Power ON Power ON Power OFF

Power ON

HDR1 function Snooze ON Power ON / Sta ndby toggle

Snooze OFF, Alarm OFF & Power OFF

Power ON

To go into frequency Tune mode to change frequency. Power OFF VOLUME VOLUME FM AM AUX IN Clock Set Alarm1 Alarm2 Backlight Hour Mode System Reset ATS Sleep Auto clock Set Clock Set Alarm1 Alarm2 Backlight Hour Mode System Reset Recall ATS table ON / OFF

RT PTY Frequency SSI Audio Mode Graphic EQ EQ Mode Time/Date Alarm1 Alarm2 Sleep BER Service mode Station ID UI Version SW Version HW Version

Note except StandBy recall the last station on last ba nd

recall the last station on last ba nd turn left / right

use ENTER to execute

Tune to change station.

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:2026

Preset 0~9

Volume

Mute

Tune

click long 2s click long hold click

click

long 0.5 s

Power ON Power ON Power ON Power ON Power ON Power ON Power ON

Go to Preset 0~9 Store Preset 0~9 VOLUME VOLUME fast Toggle Mute ON / OFF Tune next frequency step. Auto seek and go to the next station.

(include analog a nd HD station s) 11 12

14 15

HD seek Execution

Last recall News SW

click Click Click

Click

Power ON Power ON Power ON

Power ON

Power ON Power ON

Auto seek and go to the next HD station.

cycle through the multicasting programs

Enter input

Flat Classical Rock Jazz Pop My Bass My Treble

To go back to the la st station (program).

swap Audio EQ to FLAT

Note:

1. Long 2s(.5s) = press key and hold up to 2 (0.5) seconds.

2. Long hold = just press key and hold.

3. BER = Error Bit Rate.

4. SSI = Signal Strength Indicator.

5. RT = Radio Text.

6. PTY = Program Type.

7. A TS = Auto Tuning System.

On My Bass / Treble use ENTER & Tune to adjust

20070524_HDR-1_381QB0SB-A_GB.p65 2007/5/24, ¤U¤È 03:2027

Sangean HDR-1 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual