Page 1
Washing Machine
User manual
WD90K5***** / WD80K5***** / WD70K5*****
WD80(70)K5410OW_03744D_EN.indd 1 2016/7/22 14:39:05
Page 2
Contents
Safety information 3
What you need to know about the safety instructions 3
Important safety symbols 3
Important safety precautions 4
Contents
Instructions about the WEEE 14
Installation 15
What’s included 15
Installation requirements 17
Step-by-step installation 19
Before you start 25
Initial settings 25
Laundry guidelines 25
Detergent drawer guidelines 28
Operations 31
Control panel 31
Simple steps to start 33
Dry clothes Only 34
Course overview 35
Special features 38
Settings 40
Maintenance 41
Eco Drum Clean 41
Smart check 42
Using Dry course 43
AIR WASH 44
Emergency drain 45
Cleaning 46
Recovery from freezing 50
Care against an extended time of disuse 50
Troubleshooting 51
Checkpoints 51
Information codes 56
Specications 59
Fabric care chart 59
Protecting the environment 60
Specication sheet 61
2 English
WD80(70)K5410OW_03744D_EN.indd 2 2016/7/22 14:39:06
Page 3
Safety information
Congratulations on your new Samsung washing machine. This manual contains important
information on the installation, use and care of your appliance. Please take some time to read
this manual to take full advantage of your washing machine’s many benets and features.
What you need to know about the safety instructions
Please read this manual thoroughly to ensure that you know how to safely and efciently
operate the extensive features and functions of your new appliance. Please store the manual
in a safe location close to the appliance for future reference. Use this appliance only for its
intended purpose as described in this instruction manual.
Warnings and Important Safety Instructions in this manual do not cover all possible
conditions and situations that may occur. It is your responsibility to use common sense,
caution and care when installing, maintaining and operating your washing machine.
Because the following operating instructions cover various models, the characteristics of your
washing machine may differ slightly from those described in this manual and not all warning
signs may be applicable. If you have any questions or concerns, contact your nearest service
centre or nd help and information online at www.samsung.com.
Safety information
Important safety symbols
What the icons and signs in this user manual mean:
WARNING
Hazards or unsafe practices that may result in severe personal injury, death and/or property
damage.
CAUTION
Hazards or unsafe practices that may result in personal injury and/or property damage.
NOTE
Indicates that a risk of personal injury or material damage exists.
English 3
WD80(70)K5410OW_03744D_EN.indd 3 2016/7/22 14:39:06
Page 4
Safety information
These warning signs are here to prevent injury to yourself and others.
Please follow them explicitly.
After reading this manual, store it in a safe place for future reference.
Read all instructions before using the appliance.
As with any equipment that uses electricity and moving parts, potential hazards exist. To
Safety information
safely operate this appliance, familiarize yourself with its operation and exercise care when
using it.
Important safety precautions
To reduce the risk of re, electric shock, or injury to persons when
using your appliance, follow basic precautions, including the following:
WARNING
1. This appliance is not to be used by persons (including children)
with reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
2. For use in Europe: This appliance can be used by children aged from
8 years and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
3. Children should be supervised to ensure that they do not play with
the appliance.
4. If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualied persons in
order to avoid a hazard.
4 English
WD80(70)K5410OW_03744D_EN.indd 4 2016/7/22 14:39:06
Page 5
5. The new hose-sets supplied with the appliance are to be used and
that old hose-sets should not be reused.
6. For appliances with ventilation openings in the base, that a carpet
must not obstruct the openings.
7. For use in Europe: Children of less than 3 years should be kept
away unless continuously supervised.
CAUTION
8. In order to avoid a hazard due to inadvertent resetting of the
thermal cut-out, this appliance must not be supplied through an
external switching device, such as a timer, or connected to a circuit
that is regularly switched on and off by the utility.
9. The tumble dryer is not to be used if industrial chemicals have been
used for cleaning.
10. The lint trap has to be cleaned frequently, if applicable.
11. Lint must not to be allowed to accumulate around the tumble dryer.
(not applicable for appliances intended to be vented to the exterior
Safety information
of the building)
12. Adequate ventilation has to be provided to avoid the back ow of
gases into the room from appliances burning other fuels, including
open res.
13. Do not dry unwashed items in the tumble dryer.
14. Items that have been soiled with substances such as cooking oil,
acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes
and wax removers should be washed in hot water with an extra
amount of detergent before being dried in the tumble dryer.
15. Items such as foam rubber (latex foam), shower caps, waterproof
textiles, rubber backed articles and clothes or pillows tted with
foam rubber pads should not be dried in the tumble dryer.
16. Fabric softeners, or similar products, should be used as specied by
the fabric softener instructions.
English 5
WD80(70)K5410OW_03744D_EN.indd 5 2016/7/22 14:39:06
Page 6
Safety information
17. The nal part of a tumble dryer cycle occurs without heat (cool
down cycle) to ensure that the items are left at a temperature that
ensures that the items will not be damaged.
18. Remove all objects from pockets such as lighters and matches.
Safety information
19. Never stop a tumble dryer before the end of the drying cycle unless
20. Exhaust air must not be discharged into a ue which is used for
21. The appliance must not be installed behind a lockable door, a sliding
WARNING
all items are quickly removed and spread out so that the heat is
dissipated.
exhausting fumes from appliances burning gas or other fuels.
door or a door with a hinge on the opposite side to that of the
tumble dryer, in such a way that a full opening of the tumble dryer
door is restricted.
6 English
WD80(70)K5410OW_03744D_EN.indd 6 2016/7/22 14:39:06
Page 7
Critical installation warnings
WARNING
The installation of this appliance must be performed by a qualied technician or service
company.
• Failure to do so may result in electric shock, re, an explosion, problems with the product,
or injury.
The appliance is heavy, therefore take care when lifting it.
Plug the power cord into an AC 220 - 240 V / 50 Hz wall socket or higher and use the socket
for this appliance only. Never use an extension cord.
• Sharing a wall socket with other appliances using a power strip or extending the power
cord may result in electric shock or re.
• Ensure that the power voltage, frequency, and current are the same as those of the
product specications. Failure to do so may result in electric shock or re. Plug the power
plug into the wall socket rmly.
Remove all foreign substances such as dust or water from the power plug terminals and
contact points using a dry cloth on a regular basis.
• Unplug the power plug and clean it with a dry cloth.
• Failure to do so may result in electric shock or re.
• Plug the power plug into the wall socket so that the cord is running towards the oor.
If you plug the power plug into the socket in the opposite direction, the electric wires
within the cable may be damaged and this may result in electric shock or re.
Safety information
Keep all packaging materials out of the reach of children as these may be dangerous.
• If a child places a bag over its head, it may suffocate.
When the appliance, power plug or power cord is damaged, contact your nearest service
centre.
This appliance must be properly grounded.
Do not ground the appliance to a gas pipe, plastic water pipe, or telephone line.
• This may result in electric shock, re, an explosion, or problems with the product.
• Never plug the power cord into a socket that is not grounded correctly and make sure
that it is in accordance with local and national regulations.
Do not install this appliance near a heater or any inammable material.
Do not install this appliance in a humid, oily or dusty location, or in a location exposed to
direct sunlight or water (rain drops).
Do not install this appliance in a location exposed to low temperatures.
• Frost may cause the tubes to burst.
English 7
WD80(70)K5410OW_03744D_EN.indd 7 2016/7/22 14:39:06
Page 8
Safety information
Do not install this appliance in a location where gas may leak.
• This may result in electric shock or re.
Do not use an electric transformer.
• This may result in electric shock or re.
Do not use a damaged power plug, damaged power cord, or loose wall socket.
Safety information
• This may result in electric shock or re.
Do not pull or excessively bend the power cord.
Do not twist or tie the power cord.
Do not hook the power cord over a metal object, place a heavy object on the power cord,
insert the power cord between objects, or push the power cord into the space behind the
appliance.
• This may result in electric shock or re.
Do not pull the power cord when unplugging the power plug.
• Unplug the power plug by holding the plug.
• Failure to do so may result in electric shock or re.
This appliance should be positioned so that the power plug, the water supply taps, and the
drain pipes are accessible.
8 English
WD80(70)K5410OW_03744D_EN.indd 8 2016/7/22 14:39:06
Page 9
Installation cautions
CAUTION
This appliance should be positioned in such a way that the power plug is easily accessible.
• Failure to do so may result in electric shock or re due to electric leakage.
Install your appliance on a solid, level oor that can support its weight.
• Failure to do so may result in abnormal vibrations, movement, noise, or problems with
the product.
Critical usage warnings
WARNING
If the appliance is ooded, turn off the water & power supplies immediately and contact your
nearest service centre.
• Do not touch the power plug with wet hands.
• Failure to do so may result in electric shock.
If the appliance generates a strange noise, a burning smell, or smoke, unplug the power plug
immediately and contact your nearest service centre.
• Failure to do so may result in electric shock or re.
Safety information
In the event of a gas leak (such as propane gas, LP gas, etc.), ventilate immediately without
touching the power plug. Do not touch the appliance or power cord.
• Do not use a ventilating fan.
• A spark may result in an explosion or re.
Do not let children play in or on the washing machine. In addition, when disposing of the
appliance, remove the washing machine door lever.
• If trapped inside the product, children may suffocate to death.
Make sure to remove the packaging (sponge, styrofoam) attached to the bottom of the
washing machine before using it.
Do not wash items contaminated with gasoline, kerosene, benzene, paint thinner, alcohol or
other inammable or explosive substances.
• This may result in electric shock, re, or an explosion.
English 9
WD80(70)K5410OW_03744D_EN.indd 9 2016/7/22 14:39:06
Page 10
Safety information
Do not open the washing machine door by force while it is operating (high-temperature
washing/drying/spinning).
• Water owing out of the washing machine may result in burns or cause the oor to be
• Opening the door by force may result in damage to the product or injury.
Do not insert your hand under the washing machine while an operation is in progress.
Safety information
• This may result in injury.
Do not touch the power plug with wet hands.
• This may result in electric shock.
Do not turn the appliance off by unplugging the power plug while an operation is in progress.
• Plugging the power plug into the wall socket again may cause a spark and result in
Do not let children or the inrm use this washing machine without proper supervision. Do
not let children climb in or onto the appliance.
• This may result in electric shock, burns or injury.
slippery. This may result in injury.
electric shock or re.
Do not insert your hand or a metal object under the washing machine while it is operating.
• This may result in injury.
Do not unplug the appliance by pulling the power cord. Always grip the plug rmly and pull
it straight out of the outlet.
• Damage to the power cord may cause a short-circuit, re and/or electric shock.
Do not attempt to repair, disassemble, or modify the appliance yourself.
• Do not use a fuse (such as copper, steel wire, etc.) other than a standard fuse.
• When the appliance needs to be repaired or reinstalled, contact your nearest service
centre.
• Failure to do so may result in electric shock, re, problems with the product, or injury.
If the water supply hose comes loose from the water tap and oods the appliance, unplug the
power plug.
• Failure to do so may result in electric shock or re.
Unplug the power plug when the appliance is not being used for long periods of time or
during a thunder or lightning storm.
• Failure to do so may result in electric shock or re.
If any foreign substance enters into the appliance, unplug the power plug and contact you
nearest Samsung Customer Service.
• This may result in electric shock or re.
Do not let children (or pets) play in or on your washing machine. The washing machine door
does not open easily from the inside and children may be seriously injured if trapped inside.
10 English
WD80(70)K5410OW_03744D_EN.indd 10 2016/7/22 14:39:06
Page 11
Usage cautions
CAUTION
When the washing machine is contaminated by a foreign substance such as detergent, dirt,
food waste, etc., unplug the power plug and clean the washing machine using a damp, soft
cloth.
• Failure to do so may result in discolouration, deformation, damage, or rust.
The front glass may be broken by a strong impact. Take care when using the washing
machine.
• If the glass is broken, it may result in injury.
After a water supply failure or when reconnecting the water supply hose, open the water tap
slowly.
Open the water tap slowly after a long period of non-use.
• The air pressure in the water supply hose or the water pipe may damage a product part
or result in a water leak.
If a draining error occurs during an operation, check if there is a draining problem.
• If the washing machine is used when it is ooded because of a draining problem, it may
result in electric shock or re.
Safety information
Insert the laundry into the washing machine completely so that the laundry does not get
caught in the door.
• If laundry gets caught in the door, it may result in damage to the laundry or the washing
machine, or result in a water leak.
Turn the water supply off when the washing machine is not being used.
Ensure that the screws on the water supply hose connector are properly tightened.
• Failure to do so may result in property damage or injury.
Ensure that the rubber seal and front door glass are not contaminated by a foreign substance
(e.g. waste, thread, hair, etc.).
• If a foreign substance is caught in the door or the door is not completely closed, it may
cause a water leak.
Open the water tap and check if the water supply hose connector is rmly tightened and that
there is no water leak before using the product.
• If the screws on the water supply hose connector are loose, it may result in a water leak.
The product you have purchased is designed for domestic use only.
English 11
WD80(70)K5410OW_03744D_EN.indd 11 2016/7/22 14:39:06
Page 12
Safety information
Using the product for business purposes qualies as a product misuse. In this case, the
product will not be covered by the standard warranty provided by Samsung and no
responsibility can be attributed to Samsung for malfunctions or damages resulting from such
misuse.
Do not stand on the appliance or place objects (such as laundry, lighted candles, lighted
cigarettes, dishes, chemicals, metal objects, etc.) on the appliance.
Safety information
• This may result in electric shock, re, problems with the product, or injury.
Do not spray volatile material such as insecticide onto the surface of the appliance.
• As well as being harmful to humans, this may result in electric shock, re or problems
Do not place objects that generate electromagnetic elds near the washing machine.
• This may result in injury due to a malfunction.
Water drained during a high-temperature wash or drying cycle is hot. Do not touch the water.
• This may result in burns or injury.
Do not wash, spin, or dry water-proof seats, mats, or clothing (*) unless your appliance has a
special cycle for washing these items.
with the product.
(*): Woollen bedding, rain covers, shing vests, ski pants, sleeping bags, diaper covers, sweat
suits, and bicycle, motor cycle and car covers, etc.
• Do not wash thick or hard mats even if the washing machine mark is on the care label.
This may result in injury or damage to the washing machine, walls, oor, or clothing due
to abnormal vibrations.
• Do not wash throw rugs or doormats with rubber backing. The rubber backing may come
off and stick to inside the drum, and this may result in malfunction such as a drainage
error.
Do not operate the washing machine when the detergent drawer is removed.
• This may result in electric shock or injury due to a water leak.
Do not touch the insides of the drum during or just after drying as it is hot.
• This may result in burns.
Do not insert your hand into the detergent drawer.
• This may result in injury as your hand may be caught by the detergent input device.
• The liquid detergent guide (applicable models only) is not used for powder detergent.
Remove the guide when using powder detergent.
Do not place any objects (such as shoes, food waste, animals) other than laundry into the
washing machine.
• This may result in damage to the washing machine, or injury and death in the case of
pets due to the abnormal vibrations.
12 English
WD80(70)K5410OW_03744D_EN.indd 12 2016/7/22 14:39:07
Page 13
Do not press the buttons using sharp objects such as pins, knifes, ngernails, etc.
• This may result in electric shock or injury.
Do not wash laundry contaminated by oils, creams or lotions usually found in skincare shops
or massage clinics.
• This may cause the rubber seal to become deformed and result in a water leak.
Do not leave metal objects such as safety pins, hair pins or bleach in the drum for long
periods of time.
• This may cause the drum to rust.
• If rust starts appearing on the surface of the drum, apply a (neutral) cleansing agent to
the surface and use a sponge to clean it. Never use a metal brush.
Do not use dry cleaning detergent directly and do not wash, rinse, or spin laundry
contaminated by dry cleaning detergent.
• This may result in spontaneous combustion or ignition due to the heat from the oxidation
of the oil.
Do not use water from water cooling/heating devices.
• This may result in problems with the washing machine.
Do not use natural hand-washing soap for the washing machine.
• If it hardens and accumulates inside the washing machine, it may result in problems with
the product, discolouration, rust, or bad odours.
Safety information
Place socks and brassieres in a washing net and wash them with the other laundry.
Do not wash large laundry items such as bedding in the washing net.
• Failure to do so may result in injury due to abnormal vibrations.
Do not use hardened detergent.
• If it accumulates inside the washing machine, it may result in a water leak.
Make sure that the pockets of all the clothing items to be washed are empty.
• Hard, sharp objects such as coins, safety pins, nails, screws, or stones can cause extensive
damage to the appliance.
Do not wash clothing with large buckles, buttons or other heavy metal objects.
Sort the laundry by color on the basis of its colorfastness and select the recommended cycle,
water temperature and additional functions.
• This may result in discoloration or fabric damage.
Take care that children’s ngers are not caught in the door when you close it.
• Failure to do so may result in injury.
English 13
WD80(70)K5410OW_03744D_EN.indd 13 2016/7/22 14:39:07
Page 14
Safety information
Critical cleaning warnings
Do not clean the appliance by spraying water directly onto it.
Do not use the a strong acidic cleaning agent.
Safety information
Do not use benzene, thinner or alcohol to clean the appliance.
• This may result in discolouration, deformation, damage, electric shock or re.
Before cleaning or performing maintenance, unplug the appliance from the wall socket.
• Failure to do so may result in electric shock or re.
Instructions about the WEEE
WARNING
Correct Disposal of This Product (Waste Electrical & Electronic
Equipment)
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that
the product and its electronic accessories (e.g. charger, headset,
USB cable) should not be disposed of with other household waste
at the end of their working life. To prevent possible harm to the
environment or human health from uncontrolled waste disposal,
please separate these items from other types of waste and recycle
them responsibly to promote the sustainable reuse of material
resources.
Household users should contact either the retailer where they
purchased this product, or their local government ofce, for details
of where and how they can take these items for environmentally
safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product and its electronic
accessories should not be mixed with other commercial wastes for
disposal.
For information on Samsung’s environmental commitments and
product specic regulatory obligations e.g. REACH visit: samsung.
com/uk/aboutsamsung/samsungelectronics/corporatecitizenship/
data_corner.html
14 English
WD80(70)K5410OW_03744D_EN.indd 14 2016/7/22 14:39:07
Page 15
Installation
Follow these instructions carefully to ensure proper installation of the washing machine and
to prevent accidents when doing laundry.
What’s included
Make sure all the parts are included in the product package. If you have a problem with
the washing machine or the parts, contact a local Samsung customer centre or the retailer.
01
02
09
03
10
Installation
04
05
06
07
08
01 Release lever 02 Detergent drawer 03 Control panel
04 Door 05 Drum 06 Lint lter
07 Emergency drain tube 08 Filter cover 09 Worktop
10 Power plug 11 Drain hose 12 Levelling feet
11
12
English 15
WD80(70)K5410OW_03744D_EN.indd 15 2016/7/22 14:39:07
Page 16
Installation
Spanner Bolt caps Hose guide
Installation
Cold water hose Hot water hose Liquid detergent container
Cap xer
NOTE
• Bolt caps : The provided number (3 to 6) of bolt caps depends on the model.
• Hot water hose: Applicable models only.
• Liquid detergent container: Applicable models only.
16 English
WD80(70)K5410OW_03744D_EN.indd 16 2016/7/22 14:39:08
Page 17
Installation requirements
Electrical supply and grounding
• AC 220-240 V / 50 Hz fuse or circuit
breaker is required
• Use an individual branch circuit specic
to the washing machine
To ensure proper grounding, the washing
machine comes with a power cord featuring
a three-prong grounding plug for use in a
properly installed and grounded outlet.
Check with a qualied electrician or
serviceperson if you are not sure about the
grounding.
Do not modify the provided plug. If it does
not t the outlet, call a qualied electrician
to install a proper outlet.
WARNING
• Do NOT use an extension cord.
• Use only the power cord that comes
with the washing machine.
• Do NOT connect the ground wire to
plastic plumbing, gas lines, or hot water
pipes.
• Improperly connected grounding
conductors may cause electric shock.
Water supply
A proper water pressure for this washing
machine is between 50 kPa and 800 kPa.
Water pressure less than 50 kPa may cause
the water valve not to close completely. Or,
it may take longer to ll the drum, causing
the washing machine to turn off. Water taps
must be within 120 cm from the rear of the
washing machine so that the provided inlet
hoses reach the washing machine.
To reduce the risk of leaks:
• Make sure water taps are easily
accessible.
• Turn off the taps when the washing
machine is not in use.
• Check for any leaks at the water inlet
hose ttings on a regular basis.
CAUTION
Before using the washing machine for the
rst time, check all connections at the water
valve and taps for any leaks.
Drain
Samsung recommends a standpipe in
height of 60~90 cm. The drain hose must
be connected through the hose clip to the
standpipe, and the standpipe must fully
cover the drain hose.
Installation
English 17
WD80(70)K5410OW_03744D_EN.indd 17 2016/7/22 14:39:08
Page 18
Installation
Installation
Flooring
For best performance, the washing
machine must be installed on a solid oor.
Wood oors may need to be reinforced
to minimize vibration and/or unbalanced
loads. Carpeting and soft tile surfaces are
not a good resistance to vibrations and may
cause the washing machine to move slightly
during the spin cycle.
CAUTION
Do NOT install the washing machine on a
platform or a poorly supported structure.
Water temperature
Do not install the washing machine in areas
where water may freeze as the washing
machine always retains some water in its
water valves, pumps, and/or hoses. Frozen
water left in the connection parts may
cause damage to belts, the pump, and other
components of the washing machine.
Alcove or closet installation
Minimum clearance for stable operation:
Sides 25 mm Rear 50 mm
Top 25 mm Front 550 mm
If both the washing machine and a dryer
are installed in the same location, the front
of the alcove or closet must have at least
a 550 mm unobstructed air opening. Your
washing machine alone does not require a
specic air opening.
18 English
WD80(70)K5410OW_03744D_EN.indd 18 2016/7/22 14:39:08
Page 19
Step-by-step installation
STEP 1 Select a location
Location requirements:
• Solid, level surface without carpeting or ooring that may obstruct ventilation
• Away from direct sunlight
• Adequate room for ventilation and wiring
• The ambient temperature is always higher than the freezing point (0 ˚C)
• Away from a heat source
STEP 2 Remove the shipping bolts
Unpack the product package and remove all
shipping bolts.
1. Loosen all shipping bolts on the rear of
the machine using the supplied spanner.
Installation
2. Fill the holes with the supplied plastic
bolt caps.
Keep the shipping bolts for future use.
WARNING
Packaging materials can be dangerous to children. Dispose all packaging material (plastic
bags, polystyrene, etc.) out of children’s reach.
English 19
WD80(70)K5410OW_03744D_EN.indd 19 2016/7/22 14:39:09
Page 20
Installation
Installation
STEP 3 Adjust the levelling feet
1. Gently slide the washing machine into
position. Excessive force may damage
the levelling feet.
2. Level the washing machine by manually
adjusting the levelling feet.
3. When levelling is complete, tighten the
nuts using the spanner.
STEP 4 Connect the water hose
The provided hose adaptor may differ with the model. This step guides you through
connecting the connector-type adaptor. If you are provided with the screw-type adaptor, go
to 7.
Connect the water hose to the water tap.
1. Remove the adaptor (A) from the water
A
B
hose (B).
2. Use a Philips screwdriver to loosen four
screws on the adaptor.
20 English
WD80(70)K5410OW_03744D_EN.indd 20 2016/7/22 14:39:10
Page 21
3. Hold the adaptor and turn part (C) in the
C
arrow direction to loosen it by 5 mm (*).
C
Installation
4. Insert the adaptor into the water tap,
and tighten the screws while lifting up
the adaptor.
5. Turn part (C) in the arrow direction to
tighten it.
6. While holding down part (E), connect the
water hose to the adaptor. Then, release
part (E). The hose ts into the adaptor
E
with a clicking sound.
7. If you are using a screw type of water
tap, use the provided screw-type
adaptor to connect to the water tap as
shown.
English 21
WD80(70)K5410OW_03744D_EN.indd 21 2016/7/22 14:39:11
Page 22
Installation
Installation
8. Connect the other end of the water
hose to the inlet valve on the back of
the washing machine. Turn the hose
clockwise to tighten.
9. Open the water tap and check if there
are any leaks around the connection
areas. If there are water leaks, repeat the
steps above.
WARNING
Stop using the washing machine if there is a water leak, and contact a local Samsung service
centre. Otherwise, this may cause electric shock.
CAUTION
Do not stretch the water hose by force. If the hose is too short, replace the hose with a
longer, high-pressure hose.
NOTE
• After connecting the water hose to the adaptor, check if it is connected properly by
pulling the water hose downwards.
• Use a popular type of water taps. If the tap is square-shaped or too big, remove the
spacer ring before inserting the tap into the adaptor.
22 English
WD80(70)K5410OW_03744D_EN.indd 22 2016/7/22 14:39:12
Page 23
Aqua hose (applicable models only)
A
For models with an additional hot water
inlet:
1. Connect the red end of the hot water
hose to the hot water inlet on the back
of the machine.
2. Connect the other end of the hot water
hose to the hot water tap.
The aqua hose alerts users of a risk of water
leaks. It senses the water ow and turns red
on the centre indicator (A) in case of a leak.
Installation
English 23
WD80(70)K5410OW_03744D_EN.indd 23 2016/7/22 14:39:12
Page 24
Installation
A
Installation
STEP 5 Position the drain hose
The drain hose can be positioned in three ways:
Over the edge of a wash basin
The drain hose must be placed at a height
of between 60 cm and 90 cm (*) from the
oor. To keep the spout of the drain hose
bent, use the supplied plastic hose guide (A).
Secure the guide to the wall using a hook to
ensure stable drainage.
ln a sink drain pipe
The drain pipe must be above the sink
siphon so that the end of the hose is at least
60 cm above the oor.
ln a drain pipe
The drain pipe should be between 60 cm
and 90 cm high (*). It is advisable to use
a 65 cm high vertical pipe. Make sure the
drain hose is connected to the stand pipe at
a slant.
Drain standpipe requirements:
• Minimum diameter of 5 cm
• Minimum carry-away capacity of 60
litres per minute
STEP 6 Turn on the washing machine
Plug the power cord into a wall socket featuring an AC 220-240 V / 50 Hz approved electrical
outlet protected by a fuse or circuit breaker. Then, press Power to turn on the washing
machine.
24 English
WD80(70)K5410OW_03744D_EN.indd 24 2016/7/22 14:39:13
Page 25
Before you start
Initial settings
Run Calibration (recommended)
Calibration ensures accurate weight detection by the washing machine. Make sure the drum
is empty before running Calibration.
1. Power off, and then power on the washing machine.
2. Hold down Temp. and Delay End simultaneously for 3 seconds to enter Calibration
mode. The “CB” message appears.
3. Press Start/Pause to run the Calibration cycle.
4. The drum will rotate clockwise and counter-clockwise for about 3 minutes.
5. When the cycle is complete, “0” appears on the display and the washing machine will turn
off automatically.
6. The washing machine is now ready for use.
Laundry guidelines
Before you start
STEP 1 Sort
Sort the laundry according to these criteria:
• Care Label: Sort the laundry into cottons, mixed bres, synthetics, silks, wools, and rayon.
• Colour: Separate whites from colours.
• Size: Mixing different-sized items together in the drum improves the washing
performance.
• Sensitivity: Wash delicate items separately using an Easy Iron option for pure, new
woollen items, curtains, and silk items. Check the labels on the items.
NOTE
Make sure to check the care label on the clothing, and sort them accordingly before starting
the wash.
English 25
WD80(70)K5410OW_03744D_EN.indd 25 2016/7/22 14:39:13
Page 26
Before you start
STEP 2 Empty pockets
Empty all the pockets of your laundry items
• Metal objects such as coins, pins, and buckles on clothing may damage other laundry
items as well as the drum.
Turn clothing with buttons and embroideries inside out
• If pants or jacket zippers are open while washing, the drum may be damaged. Zippers
should be closed and xed with a string.
• Clothing with long strings may become entangled with other clothes. Make sure to tie the
strings before starting the wash.
STEP 3 Use a laundry net
• Brassieres (water washable) must be placed in a laundry net. Metal parts of the brassieres
may break through and tear other laundry items.
Before you start
• Small, light clothing such as socks, gloves, stockings, and handkerchiefs may become
caught around the door. Place them inside a ne laundry net.
• Do not wash the laundry net by itself without other laundry. This may cause abnormal
vibrations that could move the washing machine and result in injury.
STEP 4 Prewash (if necessary)
Select the Prewash option for the selected course if the laundry is heavily soiled. Do not use
the Prewash option when detergent is manually added into the drum.
STEP 5 Determine the load capacity
Do not overload the washing machine. Overloading may cause the washing machine to not
wash properly. For the load capacity for the type of clothing, see page 35.
NOTE
When washing bedding or bedding covers, the wash time may be lengthened or the spin
efciency may be reduced. For bedding or bedding covers, the recommended maximum spin
cycle speed is 800 rpm, and the load capacity is 2 kg or less.
CAUTION
If the laundry is unbalanced and the “UB” information code is displayed, redistribute the load.
Unbalanced laundry may reduce the spinning performance.
26 English
WD80(70)K5410OW_03744D_EN.indd 26 2016/7/22 14:39:13
Page 27
STEP 6 Apply a proper detergent type
The type of detergent depends on the type of fabric (cotton, synthetic, delicate items, wool),
colour, wash temperature, and degree of soiling. Always use “low suds” laundry detergent,
which is designed for automatic washing machines.
NOTE
• Follow the detergent manufacturer’s recommendations based on the weight of the
laundry, the degree of soiling, and the hardness of the water in your local area. If you are
not sure about the water hardness, contact a local water authority.
• Do not use detergent that tends to be hardened or solidied. This detergent may remain
after the rinse cycle, blocking the drain outlet.
CAUTION
When washing wool using the wool course, use only a neutral liquid detergent. If used with
the Wool course, powder detergent may remain on the laundry and discolour the laundry.
Laundry capsules
To get the best results from using laundry capsules, please follow these instructions.
1. Put the capsule in the bottom of the
empty drum towards the rear.
Before you start
2. Put the laundry in the drum on top of
the capsule.
English 27
WD80(70)K5410OW_03744D_EN.indd 27 2016/7/22 14:39:14
Page 28
Before you start
A
Detergent drawer guidelines
The washing machine provides a three-compartment dispenser: the left compartment for the
main wash, the middle compartment for fabric softeners, and the right compartment for the
preliminary wash.
01 Prewash compartment: Apply
prewash detergent.
02
03
Before you start
Main-wash compartment: Apply
main-wash detergent, water softener,
soaking detergent, bleach, and/or stain
removers.
Softener compartment: Apply
additives such as fabric softener. Do not
exceed the max line (A).
CAUTION
• Do not open the detergent drawer while the washing machine is operating.
• Do not use the following types of detergent:
• Tablet or capsule types
• Ball or net types
• To prevent the compartment clogging, concentrated or highly-enriched agents (fabric
softener or detergent) must be diluted with water before being applied.
To apply washing agents to the detergent drawer
1. Slide open the detergent drawer.
2. Apply laundry detergent to the
main-wash compartment as instructed
or recommended by the manufacturer.
To use liquid detergent, see page 30.
.
28 English
WD80(70)K5410OW_03744D_EN.indd 28 2016/7/22 14:39:14
Page 29
A
3. Apply fabric softener to the softener
compartment. Do not exceed the max
line (A).
4. If you want to prewash, apply
prewash detergent to the
prewash
compartment as instructed or
recommended by the manufacturer.
5. Close the detergent drawer.
Before you start
CAUTION
• Do not apply powder detergent to the
liquid container.
• Concentrated fabric softener must be
diluted with water before applied.
• Do not apply main-wash detergent to
the
WD80(70)K5410OW_03744D_EN.indd 29 2016/7/22 14:39:14
softener compartment.
English 29
Page 30
Before you start
To use liquid detergent (applicable models only)
First insert the provided liquid container
in the
apply liquid detergent to the container
below the marked max line (A).
A
Before you start
• Do not exceed the max line that is
• Remove the liquid container if using
main-wash compartment. Then,
CAUTION
marked inside the container.
powder detergent.
30 English
WD80(70)K5410OW_03744D_EN.indd 30 2016/7/22 14:39:14
Page 31
Operations
01
02
03 04 05 06
08
09
10
11
07
Control panel
01 Course Selector Turn the dial to select a course.
Before you start
02 Display
The display shows current course information and estimated time
remaining, or an information code when a problem occurs.
03 Temp. Press to change the water temperature for the current course.
04 Rinse
Press to change the rinse count for the current cycle. You can set the
rinse count to a max of 5.
Press to change the spinning speed for the current course.
• Rinse Hold (No indicator): The nal rinse cycle is suspended so
that the laundry remains in the water. To unload the laundry, run
a drain or spin cycle.
05 Spin
• No Spin
: The drum does not spin after the nal drain cycle.
• Spin Only : To run the Spin Only cycle, press Spin for 3
seconds. When the cycle time and spinning speed appear, press
Spin repeatedly until a desired spinning speed is selected. Then,
press Start/Pause to start the cycle. The spinning time depends
on the selected cycle.
06 Dry Level Press this button to select proper drying option.
07 Bubble Soak
Press to activate/deactivate the Bubble Soak function. This function
helps remove a wide variety of stubborn stains.
WD80(70)K5410OW_03744D_EN.indd 31 2016/7/22 14:39:15
English 31
Page 32
Operations
Press to select an option from Intensive , Prewash , and
08 Options
09 Delay End
10 Start/Pause Press to start or stop operation.
11 Power Press to turn on/off the washing machine.
Intensive + Prewash . Press again to deselect.
• Availability of the options depends on the cycle.
Delay End lets you set the end time of the current cycle. Based
on your settings, the start time of the cycle will be determined
by the machine’s internal logic. For example, this setting is useful
for programming your machine to nish a wash at the time you
normally return home from work.
• Press to choose a preset unit of hours.
Operations
32 English
WD80(70)K5410OW_03744D_EN.indd 32 2016/7/22 14:39:15
Page 33
Simple steps to start
1
4
3
5
6
2
1. Press Power to turn on the washing machine.
2. Turn the Course Selector to select a course.
3. Change the course settings (Temp., Rinse, Spin and Dry Level) as necessary.
4. To add an option, press Options. Use the button again to choose a preferred item.
5. The machine provides two easy to access buttons for Bubble Soak and Delay End for your
convenience. If you want to use one of these options, press the corresponding button.
6. Press Start/Pause.
Operations
English 33
WD80(70)K5410OW_03744D_EN.indd 33 2016/7/22 14:39:15
Page 34
Operations
2
3
1
4
Dry clothes Only
You can dry your clothes directly or dry the washed clothes according to the following
procedures.
1. Press Power button to turn on the washing machine.
2. Turn the Course Selector to select the appropriate drying cycle.
3. Press Dry Level button to select the appropriate drying mode.
4. Press Start/Pause button to start dry.
Operations
34 English
To change the course during operation
1. Press Start/Pause to stop operation.
2. Select a different course.
3. Press Start/Pause again to start the new course.
WD80(70)K5410OW_03744D_EN.indd 34 2016/7/22 14:39:15
Page 35
Course overview
Standard courses
Course Description
COTTON
SYNTHETICS
• For cottons, bed linens, table linens, underwear,
towels, or shirts.
The washing time and the number of rinse
cycles are automatically adjusted according to
the load.
• For blouses or shirts that are made of polyester
(diolen, trevira), polyamide (perlon, nylon), or
the like.
Max load (kg)
9kg
model
8kg
model
7kg
model
Max Max Max
4 4 3
WOOL
BABY CARE
OUTDOOR CARE
RINSE+SPIN
ECO DRUM CLEAN
• Specic for machine-washable wool for loads
less than 2 kg.
• The wool course features gentle cradling
and soaking to protect the wool bres from
shrinkage/distortion.
• A neutral detergent is recommended.
• Featuring a high-temperature wash and extra
rinses to ensure that no powder detergent
remains.
• For outdoor clothes, skiwear, and sportswear
that are made of functional materials such as
spandex, stretch, and microbre.
• Featuring an additional rinse after applying
fabric softener to the laundry.
• Cleans the drum by removing dirt and bacteria
from the drum.
• Perform once every 40 washes with no
detergent or bleach applied.
• Make sure the drum is empty.
• Do not use any cleaning agents for cleaning the
drum.
Operations
2 2 2
4 4 3
2 2 2
- - -
- - -
English 35
WD80(70)K5410OW_03744D_EN.indd 35 2016/7/22 14:39:16
Page 36
Operations
Max load (kg)
Course Description
• This course is useful for removing bad odors.
Turning the Cycle Selector cycles through the
following operating modes.(Deodorization >
Sanitization)
AIR WASH
COTTON DRY • For general drying. 6 6 5
• DEODORIZATION - Reduces bad smells from the
laundry.
• SANITIZATION - Deodorize and sanitize the
laundry by stronger AIR Wash action with
higher temp.
9kg
8kg
model
model
- - -
7kg
model
Operations
SYNTHETICS DRY
SUPER ECO WASH
15’ QUICK WASH
DAILY WASH
Options
Option Description
Intensive
Pre Wash
• A low temperature drying cycle for heatsensitive garments.
• Low-temperature Eco Bubble contributes to
power saving.
• For lightly soiled garments in less than 2 kg
that you want to wash quickly.
• For everyday items such as underwear and
shirts.
• For badly soiled laundry. The operation time for each cycle is
longer than normal.
• This will add a preliminary washing cycle before the main
wash cycle.
3 3 3
4 4 3
2 2 2
2 2 2
36 English
WD80(70)K5410OW_03744D_EN.indd 36 2016/7/22 14:39:16
Page 37
Option Description
• Bubble Soak helps remove a variety of stubborn stains.
• With Bubble Soak selected, laundry is thoroughly soaked in
Bubble Soak
water bubbles for effective washing.
• Bubble Soak is available with and adds up to 30 minutes to 3
cycles: Cotton, Synthetics, and Baby Care.
Delay End
You can set the washing machine to nish your wash automatically at a later time, choosing a
delay of between 1 to 24 hours (in 1 hour increments). The hour displayed indicates the time
the wash will nish.
1. Select a course. Then change the cycle settings if necessary.
2. Press Delay End repeatedly until a desired end time is set.
3. Press Start/Pause.
The corresponding indicator turns on with the clock running.
4. To cancel the Delay End, restart the washing machine by pressing Power.
Real-life case
You want to nish a two-hour course 3 hours later from now. For this, you add the Delay End
option to the current cycle with the 3-hour setting, and press Start/Pause at 2:00 p.m. Then,
what happens? The washing machine starts operating at 3:00 p.m., and ends at 5:00 p.m.
Provided below is the time line for this example.
Operations
2:00 pm
Set the Delay End to 3 hours
WD80(70)K5410OW_03744D_EN.indd 37 2016/7/22 14:39:16
3:00 pm
Start
5:00 pm
End
English 37
Page 38
Operations
Operations
Special features
AddWash
When the AddWash indicator turns on, you can stop operation of the machine and put
additional laundry or softener into the drum. The Add Door opens by more than 130° for
easy access.
1. Press Start/Pause to stop operation.
2. Press the upper area of the Add Door
until you hear a clicking sound to unlock.
Pull the handle of the Add Door to open.
3. Open the Add Door and insert additional
laundry or softener into the drum.
4. Push to lock the Add Door until you hear
a clicking sound.
5. Press Start/Pause to resume operation.
CAUTION
Do not put excessive force on the Add Door.
It may break.
NOTE
The water inside the drum does not leak if the Add Door is closed properly. Water drops may
form around the window, but they do not leak from inside the drum.
38 English
WD80(70)K5410OW_03744D_EN.indd 38 2016/7/22 14:39:17
Page 39
CAUTION
• Do not open the Add Door if suds have formed inside the drum that rise above the level
of the Add Door.
• Do not attempt to open the Add Door while the machine is operating without rst
pressing Start/Pause. Please note that the Add Door can be opened unintentionally
(without pressing Start/Pause) when the wash is complete.
• Do not add an excessive load through the Add Door. Performance may be degraded.
• Do not use the lower area of the Add Door as a handle. Your ngers may be caught.
• Make sure that no laundry is caught in the Add Door.
• Keep your pets out of the washing machine, especially the Add Door.
• When using hot water for the wash, the Add Door seems to leak water after opening and
closing the Add Door. This is normal, simply because steam emerging from the open Add
Door has cooled and formed water drops on the surface.
• When the Add Door closes, the door seals up and no water can leak. However, you
may encounter what appears to be water leak around the door - some residual water
remaining around the Add Door may form water drops. This is normal.
• Neither the main door or the Add Door can opened when the water temperature is over
50 ˚C. If the water level inside the drum is over a certain point, the main door cannot be
opened.
• If an information code of DDC appears on the display, see the “Information codes” section
for further actions.
Operations
English 39
WD80(70)K5410OW_03744D_EN.indd 39 2016/7/22 14:39:17
Page 40
Operations
Settings
Operations
Child Lock
To prevent accidents by children, Child Lock
locks all buttons except for Power.
• To set the Child Lock function, hold
down Temp. and Rinse simultaneously
for 3 seconds. To activate, press
Start/ Pause.
• Before you press Start/Pause, you can
still open the door or change settings
by pressing corresponding buttons.
Once you press Start/Pause to run the
machine, Child Lock will be activated.
To deactivate Child Lock temporarily
Open the door, and hold down both Temp.
and Rinse simultaneously for 3 seconds.
Child Lock is deactivated temporarily for
1 minute, and the indicator blinks. Add
laundry, for example, and close the door
within the next 2 minutes. Otherwise, the
machine sounds an alert for another 2
minutes. Once you close the door, Child Lock
will be reactivated with the indicator turned
on.
Sound On/Off
You can turn on or off the key. Your setting
will remain effective after you restart the
machine.
• To mute the sound, hold down Rinse and
Spin simultaneously for 3 seconds.
• To unmute the sound, hold down again
for 3 seconds.
NOTE
In the Child Lock state, you must rs
deactivate the Child Lock if you want to add
detergent or laundry, or change the current
settings.
To cancel the Child Lock
Press and hold Temp. and Rinse
simultaneously for 6 seconds. Alternatively,
when the Child Lock is deactivated
temporarily, press and hold Temp. and Rinse
simultaneously for 3 seconds.
40 English
WD80(70)K5410OW_03744D_EN.indd 40 2016/7/22 14:39:17
Page 41
Maintenance
Keep the washing machine clean to prevent deteriorated performance and to preserve its life
cycle.
Eco Drum Clean
Perform this course regularly to clean the drum and to remove bacteria from it.
1. Press Power to turn on washing machine.
2. Turn the Cycle Selector to select ECO DRUM CLEAN.
3. Press Start/Pause.
NOTE
The water temperature for ECO DRUM CLEAN is set to 70 °C, which cannot be changed.
Due to the features of the washing machine, the water temperature is set to 70 ˚C during the
Eco Drum Clean cycle, but the display can only show 60 ˚C on the control panel.
CAUTION
Do not use any cleaning agents for cleaning the drum. Chemical residue in the drum
deteriorates the washing performance.
English 41
Maintenance
WD80(70)K5410OW_03744D_EN.indd 41 2016/7/22 14:39:18
Page 42
Maintenance
Smart check
To enable this function, you must rst download the Samsung Smart Washer app at the Play
Store or the Apple Store, and install it on a mobile device featuring a camera function.
The Smart Check function has been
optimized for Galaxy & iPhone series
(applicable models only).
1. Press and hold Spin and Dry Level
simultaneously for 3 seconds to enter
the Smart Check mode.
2. The washing machine starts the selfdiagnosis procedure and displays
an information code if a problem is
detected.
3. Run the Samsung Smart Washer app
on your mobile device, and tap Smart
Check.
4. Put the mobile device close to the
washing machine’s display so that the
mobile device and the washing machine
face each other. Then, the information
code will be recognized automatically by
the app.
5. When the information code is
recognized correctly, the app provides
Maintenance
detailed information about the problem
with applicable counteractions.
NOTE
• The function name, Smart Check, may
differ depending on the language.
• If the washing machine reets light
on the display, the app may fail to
recognize the information code.
• If the app fails to recognize the Smart
Check code consecutively, enter the
information code manually onto the app
screen.
42 English
WD80(70)K5410OW_03744D_EN.indd 42 2016/7/22 14:39:18
Page 43
Using Dry course
All drying options except for the Time Dry option detect the weight of the laundry in order to
display a more accurate drying time and dry the laundry more effectively.
Refer to the chart below to select the appropriate drying option according to the type and
amount of laundry and the moisture you want to leave.
Mode Drying option Usage
Auto Drying
Manual Drying
Cupboard
Time Dry
Use this option to dry laundry such as
cotton, underwear, and linen.
Use this option to dry the laundry for
the specied peiod of time depending
on the bes, amount of laundry
quantity and moisture.
NOTE
• The drying result may differ depending
on the selected washing cycle and the
type/amount of laundry.
• If both washing and drying cycles are
selected, the spin speed is automatically
set to enhance the drying efciency.
• In case you want to dry laundry after
a hand wash, turn the cycle selector to
select the spin cycle, and then select a
drying option for best performance.
• When drying is complete, dust from
the dry surface of the clothes may
remain on the diaphragm due to the
ironing effect that prevents wrinkles.
The dus will be washed away during the
following wash. Alternatively, you can
easily remove it with a damp towel or
cloth.
Load capacity(kg)
Cotton Dry Synthetics Dry
9kg model(6 kg)
8kg model(6 kg)
7kg model(5 kg)
30 ~ 270 min.
(in 30 minutes
increments).
3 kg
30 ~ 270 min.
(in 30 minutes
increments).
CAUTION
• Do not use the drying function after
applying a chlorine bleach agent to the
laundry during a wash or drying cycle.
Otherwise, the laundry may become
discolored or the material may be
damaged.
• Do not use the drying function for
clothing with fur lining or made from
acrylic material. This may result in the
drying function being degraded.
• Do not touch the insides of the drum or
the washing machine surface during or
just after drying as it may be hot. This
may result in burns.
Maintenance
English 43
WD80(70)K5410OW_03744D_EN.indd 43 2016/7/22 14:39:18
Page 44
Maintenance
AIR WASH
The Air Wash function refreshes garments through Samsung’s unique air-washing
technology without the need for water.
Refer to the chart below for the usage and cycle time of each Air Wash cycle.
Cycle Usage Cycle time
Deodorization Use this cycle to remove bad odors from the laundry. 29min
Sanitization Use this cycle to remove bad odors and bacteria from the laundry. 59min
NOTE
• The recommended maximum load
capacity for the Air Wash cycles is 1
kg or less (one or two items). If you
overload the drum,, the deodorization or
sanitization efciey may be reduced.
• You can add a fragrance sheet to the
laundry to add fragrance during the Air
Wash cycle.
Maintenance
CAUTION
Do not use any Air Wash cycles for the
following items
• Heat-sensitive garments made from
leather, mink, fur, silk, etc.
• Underwear trimmed with lace, doll
cushions, and trims on dress suits may
become loose.
• Clothes trimmed with buttons can cause
them to break.
• Clothes full of starch may become
deformed.
• Hard bedding
• Electric blankets, furry or bulky blankets
• Latex pillows
44 English
WD80(70)K5410OW_03744D_EN.indd 44 2016/7/22 14:39:18
Page 45
Emergency drain
A
B
C
In case of a power failure, drain the water inside the drum before taking out the laundry.
1. Power off and unplug the washing
machine from the electrical outlet.
2. Gently press the top area of the lter
cover (A) to open.
3. Put an empty, spacious container around
the cover, and stretch the emergency
drain tube to the container while holding
the tube cap (B).
Maintenance
4. Open the tube cap and let water in the
Emergency drain tube (C) ow into the
container.
5. When done, close the tube cap, and
reinsert the tube. Then, close the lter
cover.
NOTE
Use a spacious container because the water
in the drum may be more than expected.
English 45
WD80(70)K5410OW_03744D_EN.indd 45 2016/7/22 14:39:19
Page 46
Maintenance
A
Cleaning
Surface of the washing machine
Use a soft cloth with a nonabrasive household detergent. Do not spray water onto the
washing machine.
Add Door
1. Open the Add Door.
2. Use a wet cloth to clean the Add Door.
- Do not use cleaning agents.
Discolouration may occur.
- Use caution when cleaning the rubber
packing and the locking mechanism
(A).
- Dust off the window area regularly.
3. Wipe up and close the Add Door until
you hear a clicking sound.
CAUTION
• Do not apply force on the Add Door. It may break.
• Do not leave the Add Door open while the machine is operating.
• Do not put heavy objects on the Add Door at any time.
• To prevent physical injury, do not touch the Add Door while the drum is rotating.
• Do not open the Add Door while the machine is operating. This may cause physical injury.
• Do not manipulate the feature panel while the Add Door is open. This may cause physical
injury or system failure.
Maintenance
• Do not input objects other than laundry.
• Do not input bulky items to the drum through the Add Door.
• Do not pull out the rubber packing of the Add Door when cleaning. This may cause
damage.
46 English
WD80(70)K5410OW_03744D_EN.indd 46 2016/7/22 14:39:19
Page 47
Mesh lter
Clean the mesh lter of the water hose once or twice a year.
1. Turn off the washing machine, and
unplug the power cord.
2. Close the water tap.
3. Loosen and disconnect the water hose
from the back of the washing machine.
Cover the hose with a cloth to prevent
water from gushing out.
4. Use pliers to pull out the mesh lter
from the inlet valve.
5. Submerge the mesh lter deeply in
water so that the threaded connector is
also submerged.
6. Dry the mesh lter completely in the
shade.
7. Reinsert the mesh lter into the inlet
valve, and reconnect the water hose to
the inlet valve.
8. Open the water tap.
Maintenance
NOTE
If the mesh lter is clogged, an information code of “4C” appears on the screen.
English 47
WD80(70)K5410OW_03744D_EN.indd 47 2016/7/22 14:39:20
Page 48
Maintenance
A
Pump lter
It is advisable to clean the pump lter 5 or 6 times a year to prevent its clogging. A clogged
pump lter may reduce the bubble effect.
1. Turn off the washing machine, and
unplug the power cord.
2. Drain the remaining water inside the
drum by referring to “Emergency drain”
on page 45.
3. Gently press the top area of the lter
cover to open.
4. Turn the pump lter knob (A) to the left,
and drain off the remaining water.
5. Clean the pump lter using soft brushes.
Make sure the drain pump propeller
inside the lter is unclogged.
6. Reinsert the pump lter, and turn the
lter knob to the right.
Maintenance
48 English
NOTE
• Some pump lters feature a safety knob
that is designed to prevent accidents
by children. To open the safety knob
of the pump lter, push in and turn it
anticlockwise. The spring mechanism of
the safety knob helps open the lter.
• To close the safety knob of the pump
lter, turn it clockwise. The spring makes
a rattling sound, which is normal.
NOTE
If the pump lter is clogged, an information code of “5C” appears on the screen.
CAUTION
• Make sure the lter cap is closed properly after cleaning the lter. Otherwise, this may
cause a leak.
• Make sure the lter is inserted properly after cleaning it. Otherwise, this may cause an
operational failure or a leak.
WD80(70)K5410OW_03744D_EN.indd 48 2016/7/22 14:39:21
Page 49
Detergent Drawer
A
1. While holding down the release lever (A)
on the inner of the drawer, slide open
the drawer.
2. Remove the release lever and the liquid
detergent container from the drawer.
3. Clean the drawer components in owing
water using a soft brush.
4. Clean the drawer recess using a soft
brush.
5. Reinsert the release lever and the liquid
detergent container to the drawer.
6. Slide the drawer inward to close it.
NOTE
To remove remaining detergent, perform the RINSE+SPIN course with the drum being empty.
English 49
Maintenance
WD80(70)K5410OW_03744D_EN.indd 49 2016/7/22 14:39:21
Page 50
Maintenance
Recovery from freezing
The washing machine may freeze when it drops below 0 °C.
1. Turn off the washing machine, and unplug the power cord.
2. Pour warm water over the water tap to loosen the water hose.
3. Disconnect the water hose, and soak it in warm water.
4. Pour warm water into the drum and leave it for about 10 minutes.
5. Reconnect the water hose to the water tap.
NOTE
If the washing machine still doesn’t operate normally, repeat the above steps until it operates
normally.
Care against an extended time of disuse
Avoid leaving the washing machine unused for an extended time.
If this is the case, drain the washing machine and unplug the power cord.
1. Turn the Cycle Selector to select a RINSE+SPIN.
2. Empty the drum, and press Start/Pause.
3. When the cycle is complete, close the water tap and disconnect the water hose.
4. Turn off the washing machine, and unplug the power cord.
5. Open the door to let air circulate through the drum.
Maintenance
50 English
WD80(70)K5410OW_03744D_EN.indd 50 2016/7/22 14:39:21
Page 51
Troubleshooting
Checkpoints
If you encounter a problem with the washing machine, rst check the table below and try the
suggestions.
Problem Action
• Make sure the washing machine is plugged in.
• Make sure the door is properly closed.
• Make sure the water taps are open.
• Make sure to press or tap Start/Pause to start the washing
Does not start.
Water supply is
insufcient, or no
water is supplied.
machine.
• Make sure Child Lock
• Before the washing machine starts to ll, it will make a series
of clicking noises to check the door lock and does a quick
drain.
• Check the fuse or reset the circuit breaker.
• Fully open the water tap.
• Make sure the door is properly closed.
• Make sure the water supply hose is not frozen.
• Make sure the water supply hose is not kinked or clogged.
• Make sure there is sufcient water pressure.
is not activated.
After a cycle,
detergent remains in
the detergent drawer.
• Make sure the washing machine is running with sufcient
water pressure.
• Make sure the detergent is added to the centre of the
detergent drawer.
• Make sure the rinse cap is inserted properly.
• If using granular detergent, make sure the detergent selector is
in the upper position.
• Remove the rinse cap and clean the detergent drawer.
English 51
Troubleshooting
WD80(70)K5410OW_03744D_EN.indd 51 2016/7/22 14:39:21
Page 52
Troubleshooting
Problem Action
• Make sure the washing machine is installed on a level, solid
oor that is not slippery.
If the oor is not level, use the levelling feet to adjust the
height of the washing machine.
• Make sure the shipping bolts are removed.
Excessive vibrations
or makes noise.
Does not drain and/
or spin.
• Make sure the washing machine is not contacting any other
object.
• Make sure the laundry load is balanced.
• The motor can cause noise during normal operation.
• Overalls or metal-decorated clothes can cause noise while
being washed. This is normal.
• Metal objects such as coins can cause noise. After washing,
remove these objects from the drum or lter case.
• Make sure the drain hose is straightened all the way to the
drain system. If you encounter a drain restriction, call for
service.
• Make sure the debris lter is not clogged.
• Close the door and press or tap Start/Pause. For your safety,
the washing machine will not tumble or spin unless the door is
closed.
• Make sure the drain hose is not frozen or clogged.
• Make sure the drain hose is connected to a drain system that is
not clogged.
• If the washing machine is not supplied with sufcient power,
the washing machine temporarily will not drain or spin.
As soon as the washing machine regains sufcient power, it
will operate normally.
• Press or tap Start/Pause to stop the washing machine.
• It may take a few moments for the door lock mechanism to
Troubleshooting
The door does not
open.
52 English
WD80(70)K5410OW_03744D_EN.indd 52 2016/7/22 14:39:22
disengage.
• The door will not open until 3 minutes after the washing
machine has stopped or the power turned off.
• Make sure all the water in the drum is drained.
• The door may not open if water remains in the drum. Drain the
drum and open the door manually.
• Make sure the door lock light is off. The door lock light turns
off after the washing machine has drained.
Page 53
Problem Action
Excessive suds.
Cannot apply
additional detergent.
Stops.
• Make sure the Auto Detergent and Auto Softener settings are
properly congured.
• Make sure you use the recommended types of detergent as
appropriate.
• Use high efciency (HE) detergent to prevent oversudsing.
• Reduce the detergent amount for soft water, small loads, or
lightly soiled loads.
• Non-HE detergent is not recommended.
• Make sure the remaining amount of detergent and fabric
softener is not over the limit.
• Make sure the Auto Dispense function is activated, with both
the Water Hardness and Concentration settings properly
specied.
• Plug the power cord into a live electrical outlet.
• Check the fuse or reset the circuit breaker.
• Close the door and press or tap Start/Pause to start the
washing machine.
For your safety, the washing machine will not tumble or spin
unless the door is closed.
• Before the washing machine starts to ll, it will make a series
of clicking noises to check the door lock and does a quick
drain.
• There may be a pause or soak period in the cycle. Wait briey
and the washing machine may start.
• Make sure the mesh lter of the water supply hose at the
water taps are not clogged. Periodically clean the mesh lter.
• If the washing machine is not supplied with sufcient power,
the washing machine temporarily will not drain or spin. As
soon as the washing machine regains sufcient power, it will
operate normally.
Troubleshooting
English 53
WD80(70)K5410OW_03744D_EN.indd 53 2016/7/22 14:39:22
Page 54
Troubleshooting
Problem Action
• Fully open both taps.
• Make sure the temperature selection is correct.
• Make sure the hoses are connected to the correct taps. Flush
water lines.
• Make sure the water heater is set to supply a minimum
120 °F (49 °C) hot water at the tap. Also, check the water
heater capacity and recovery rate.
• Disconnect the hoses and clean the mesh lter. The mesh lter
Fills with the wrong
water temperature.
may be clogged.
• While the washing machine lls, the water temperature may
change as the automatic temperature control feature checks
incoming water temperature. This is normal.
• While the washing machine lls, you may notice just hot and/
or just cold water going through the dispenser when cold or
warm temperatures are selected.
This is a normal function of the automatic temperature
control feature as the washing machine determines the water
temperature.
Troubleshooting
Load is wet at the
end of a cycle.
Leaks water.
Has odours.
No bubbles are seen
(Bubbleshot models
only).
• Use the High or Extra High spin speed.
• Use high efciency (HE) detergent to reduce oversudsing.
• Load is too small. Small loads (one or two items) may become
unbalanced and not spin completely.
• Make sure the drain hose is not kinked or clogged.
• Make sure the door is properly closed.
• Make sure all hose connections are tight.
• Make sure the end of the drain hose is correctly inserted and
secured to the drain system.
• Avoid overloading.
• Use high efciency (HE) detergent to prevent oversudsing.
• Excessive suds collect in recesses and can cause foul odours.
• Run cleansing cycles to sanitize periodically.
• Clean the door seal (diaphragm).
• Dry the washing machine interior after a cycle has nished.
• Overloading may screen bubbles.
• Severely contaminated laundry may not generate bubbles.
54 English
WD80(70)K5410OW_03744D_EN.indd 54 2016/7/22 14:39:22
Page 55
Problem Action
• The Add Door can be opened only when the indicator
appears. However, it does not open in the following cases:
Can I open the Add
Door at any time?
- When the boiling or drying process is running and the
internal temperature becomes high.
- If you set the Child Lock for safety reasons.
- When the drum wash or drum drying cycle is running that
does not involve additional laundry.
If a problem persists, contact a local Samsung service centre.
English 55
WD80(70)K5410OW_03744D_EN.indd 55 2016/7/22 14:39:22
Troubleshooting
Page 56
Troubleshooting
Information codes
If the washing machine fails to operate, you may see an information code on the screen.
Check the table below and try the suggestions.
Problem Action
Water is not supplied.
• Make sure the water taps are open.
• Make sure the water hoses are not clogged.
• Make sure the water taps are not frozen.
• Make sure the washing machine is operating with sufcient
water pressure.
4C
• Make sure that the cold water tap and the hot water tap are
properly connected.
• Clean the mesh lter as it may be clogged.
NOTE
When the washer displays the “4C” code, the washer do
draining for 3 minutes. During this time, the Power button is
inoperative.
Troubleshooting
4C2
5C
DC
DC1
• Make sure the cold water supply hose is rmly connected to
the cold water tap.
If it is connected to the hot water tap, the laundry may be
deformed with some cycles.
Water is not draining.
• Make sure the drain hose is not frozen or clogged.
• Make sure the drain hose is positioned correctly, depending
on the connection type.
• Clean the debris lter as it may be clogged.
• Make sure the drain hose is straightened all the way to the
drain system.
• If the information code remains, contact a customer service
centre.
Operating the washer with the door open.
• Make sure the door is properly closed.
• Make sure laundry is not caught in the door.
The Main Door lock/unlock is not working properly.
• Turn the machine off, and restart the cycle.
• If the information code remains, contact a customer service
centre.
56 English
WD80(70)K5410OW_03744D_EN.indd 56 2016/7/22 14:39:22
Page 57
Problem Action
The Add Door lock/unlock is not working properly.
DC3
• Turn the machine off, and restart the cycle.
• If the information code remains, contact a customer service
centre.
Water is overowed.
OC
• Restart after spinning.
• If the information code remains on the display, contact a local
Samsung service centre.
Check the drain hose.
LC
• Make sure the end of the drain hose is placed on the oor.
• Make sure the drain hose is not clogged.
• If the information code remains, contact a customer service
centre.
NOTE
LC1
When the washer displays the “LC”/“LC1” code, the washer
do draining for 3 minutes. During this time, the Power
button is inoperative.
Spinning does not work.
• Make sure laundry is spread out evenly.
• Make sure the washing machine is on a at, stable surface.
UB
• Redistribute the load. If only one item of clothing needs
washing, such as a bathrobe or pair of jeans, the nal spin
result might be unsatisfactory, and an “UB” check message
will be shown in the display.
Check the Motor for operation.
3C
• Try restarting the cycle.
• If the information code remains, contact a customer service
centre.
The electronic control needs to be checked (Over Voltage Error).
• Check the PCB and wire harness.
• Check if power is supplied properly.
• If the information code remains, contact a customer service
UC
centre.
Low voltage detected
• Check if the power cord is plugged in.
• If the information code remains, contact a customer service
centre.
English 57
WD80(70)K5410OW_03744D_EN.indd 57 2016/7/22 14:39:22
Troubleshooting
Page 58
Troubleshooting
Problem Action
High temperature heating check
HC
1C
8C
• If the information code remains, contact a customer service
centre.
The WaterLevel sensor is not working properly.
• Try power off and restarting the cycle.
• Check WaterLevel Sensor wire harness.
• If the information code remains, contact a customer service
centre.
NOTE
When the washer displays the “1C” code, the washer do
draining for 3 minutes. During this time, the Power button is
inoperative.
The MEMS sensor is not working properly.
• Turn the machine off, and restart the cycle.
• If the information code remains, contact a customer service
centre.
Troubleshooting
Check communications between main and sub PBAs.
AC
AC6
DDC
If any information code keeps appearing on the screen, contact a local Samsung service
centre.
• Try power off and restarting the cycle.
• If the information code remains, contact a customer service
centre.
Check communications between main and inverter PBAs.
• Depending on the state, the machine may automatically returns
to normal operation.
• Turn the machine off, and restart the cycle.
• If the information code remains, contact a customer service
centre.
This message appears when you open the Add Door without
pressing Pause. If this happens, do one of the following:
• To add laundry, press the Add Door to close it properly. Then,
press Start/Pause and try again.
• If you press the Add Door by mistake, press the Add Door
again to close it properly. Then, press Start/Pause to resume
operation.
58 English
WD80(70)K5410OW_03744D_EN.indd 58 2016/7/22 14:39:22
Page 59
Specications
Fabric care chart
The following symbols provide garment care directions. The care labels include four symbols
in this order: washing, bleaching, drying and ironing (and dry cleaning when necessary).
The use of symbols ensures consistency among garment manufacturers of domestic and
imported items. Follow the care label directions to maximize garment life and reduce laundry
problems.
Resistant material Do not iron
Delicate fabric
Item can be washed at 95 ˚C Dry Clean
Item can be washed at 60 ˚C
Item can be washed at 40 ˚C
Item can be washed at 30 ˚C Do not dry clean
Hand wash only Dry at
Dry clean only Can be hung to dry
Can be bleached in cold water Dry on clothes hanger
Do not bleach Tumble dry, normal heat
Can be ironed at 200 ˚C max Tumble dry, reduced heat
Can be dry cleaned using any
solvent
Dry clean with perchloride,
lighter fuel, pure alcohol or
R113 only
Dry clean with aviation fuel,
pure alcohol or R113 only
Can be ironed at 150 ˚C max Do not tumble dry
Can be ironed at 100 ˚C max
English 59
WD80(70)K5410OW_03744D_EN.indd 59 2016/7/22 14:39:29
Specications
Page 60
Specications
Protecting the environment
• This appliance is manufactured from recyclable materials. If you decide to dispose of this
appliance, please observe local waste disposal regulations. Cut off the power cord so that
the appliance cannot be connected to a power source. Remove the door so that animals
and small children cannot get trapped inside the appliance.
• Do not exceed the detergent quantities recommended in the detergent manufacturer’s
instructions.
• Use stain removal products and bleaches before the wash cycle only when strictly
necessary.
• Save water and electricity by only washing full loads (the exact amount depends upon
the program used).
Specications
60 English
WD80(70)K5410OW_03744D_EN.indd 60 2016/7/22 14:39:29
Page 61
Specication sheet
“ * ” Asterisk(s) means variant model and can be varied (0-9) or (A-Z).
Type Front loading washing machine
Model name WD90K54**** WD80K54**** WD70K54****
Wash and spin capacity 9.0 kg 8.0 kg 7.0 kg
Power
consumption
Dimensions
W600 x D650
x H850 (mm)
W600 x D600
x H850 (mm)
W600 x D550
x H850 (mm)
Water pressure 50 kPa ~ 800 kPa
NET weight 71 kg 72 kg 66 kg
Dry capacity 6.0 kg 6.0 kg 5.0 kg
220 V 100 W
Washing
240 V 100 W
Washing and
heating
220 V 2000 W
240 V 2400 W
220 V 1600 W
Drying
240 V 1600 W
Spin 220~240 V 450 W
Pumping 30 W
Spin revolutions 1400 rpm
NOTE
The design and specications are subject to change without notice for quality improvement
purposes.
English 61
WD80(70)K5410OW_03744D_EN.indd 61 2016/7/22 14:39:29
Specications
Page 62
Specications
Specications
According to Regulation (EU) No. 90/60/EC
“ * ” Asterisk(s) means variant model and can be varied (0-9) or (A-Z).
Samsung
Model Name WD90K54****
Energy Efciency Class
A (most efcient) to G (least efcient) A
Energy Consumption
Washing, spinning, and drying kWh 6.12
Washing and spinning only kWh 1.17
Washing Performance Class
A (most efcient) to G (least efcient) A
Water Extraction Efciency Class
A (most efcient) to G (least efcient) A
Residual moisture % 44
Maximum Spin Speed rpm 1400
Capacity
Washing kg 9
Drying kg 6
Water Consumption
Washing, spinning, and drying
Washing and spinning only
Program time for complete operating cycle (60 ºC cotton
washing and ‘dry cotton’ drying for rated washing capacity)
Washing, spinning, and drying min 705
Washing and spinning only min 280
Programs to which the information on the label
and the Sheet relate
Estimatd annual consumption for a 4-person household,
always using the dries (200 cycles)
Energy Consumption kWh/yr 1224
Water Consumption
Estimatd annual consumption for a 4-person household,
never using the drier (200 cycles)
Energy Consumption
Water Consumption
ℓ
ℓ
Wash Cotton 60 ºC + Intensive + 1400rpm
Dry Cotton Dry + Cup board + Spin
ℓ
kWh/yr 234
ℓ
99
54
19800
10800
62 English
WD80(70)K5410OW_03744D_EN.indd 62 2016/7/22 14:39:30
Page 63
The drying energy consumption data has been measured under the conditions specied in
Standard EN50229.
• First drying should be performed with 3 kg load (the load consist: 1 sheets and 6
pillowcases and 7 towels) by selecting Cotton Dry (Cupboard) + Spin (1400);
• Second drying should be performed with 3 kg load (the load consist: 1 sheets and 6
pillowcases and 7 towels) by selecting Cotton Dry (Cupboard) + Spin (1400);
• Third drying should be performed with 3 kg load (the load consist: 1 sheets and 6
pillowcases and 7 towels) by selecting Cotton Dry (Cupboard) + Spin (1400);
(1 or 2 towels can be added or removed for setting weight.)
English 63
WD80(70)K5410OW_03744D_EN.indd 63 2016/7/22 14:39:30
Specications
Page 64
Specications
Specications
According to Regulation (EU) No. 90/60/EC
“ * ” Asterisk(s) means variant model and can be varied (0-9) or (A-Z).
Samsung
Model Name WD80K54****
Energy Efciency Class
A (most efcient) to G (least efcient) A
Energy Consumption
Washing, spinning, and drying kWh 5.44
Washing and spinning only kWh 1.04
Washing Performance Class
A (most efcient) to G (least efcient) A
Water Extraction Efciency Class
A (most efcient) to G (least efcient) A
Residual moisture % 44
Maximum Spin Speed rpm 1400
Capacity
Washing kg 8
Drying kg 6
Water Consumption
Washing, spinning, and drying
Washing and spinning only
Program time for complete operating cycle (60 ºC cotton
washing and ‘dry cotton’ drying for rated washing capacity)
Washing, spinning, and drying min 690
Washing and spinning only min 280
Programs to which the information on the label
and the Sheet relate
Estimatd annual consumption for a 4-person household,
always using the dries (200 cycles)
Energy Consumption kWh/yr 1088
Water Consumption
Estimatd annual consumption for a 4-person household,
never using the drier (200 cycles)
Energy Consumption
Water Consumption
ℓ
ℓ
Wash Cotton 60 ºC + Intensive + 1400rpm
Dry Cotton Dry + Cup board + Spin
ℓ
kWh/yr 208
ℓ
88
48
17600
9600
64 English
WD80(70)K5410OW_03744D_EN.indd 64 2016/7/22 14:39:30
Page 65
The drying energy consumption data has been measured under the conditions specied in
Standard EN50229.
• First drying should be performed with 3 kg load (the load consist: 1 sheets and 2
pillowcases and 7 towels) by selecting Cotton Dry (Cupboard) + Spin (1400);
• Second drying should be performed with 3 kg load (the load consist: 1 sheets and 6
pillowcases and 7 towels) by selecting Cotton Dry (Cupboard) + Spin (1400);
• Third drying should be performed with 2 kg load (the load consist: 1 sheets and 6
pillowcases and 7 towels) by selecting Cotton Dry (Cupboard) + Spin (1400);
(1 or 2 towels can be added or removed for setting weight.)
English 65
WD80(70)K5410OW_03744D_EN.indd 65 2016/7/22 14:39:30
Specications
Page 66
Specications
Specications
According to Regulation (EU) No. 90/60/EC
“ * ” Asterisk(s) means variant model and can be varied (0-9) or (A-Z).
Samsung
Model Name WD70K54****
Energy Efciency Class
A (most efcient) to G (least efcient) A
Energy Consumption
Washing, spinning, and drying kWh 4.76
Washing and spinning only kWh 0.91
Washing Performance Class
A (most efcient) to G (least efcient) A
Water Extraction Efciency Class
A (most efcient) to G (least efcient) A
Residual moisture % 44
Maximum Spin Speed rpm 1400
Capacity
Washing kg 7
Drying kg 5
Water Consumption
Washing, spinning, and drying
Washing and spinning only
Program time for complete operating cycle (60 ºC cotton
washing and ‘dry cotton’ drying for rated washing capacity)
Washing, spinning, and drying min 655
Washing and spinning only min 280
Programs to which the information on the label
and the Sheet relate
Estimatd annual consumption for a 4-person household,
always using the dries (200 cycles)
Energy Consumption kWh/yr 952
Water Consumption
Estimatd annual consumption for a 4-person household,
never using the drier (200 cycles)
Energy Consumption
Water Consumption
ℓ
ℓ
Wash Cotton 60 ºC + Intensive + 1400rpm
Dry Cotton Dry + Cup board + Spin
ℓ
kWh/yr 182
ℓ
77
42
15400
8400
66 English
WD80(70)K5410OW_03744D_EN.indd 66 2016/7/22 14:39:30
Page 67
The drying energy consumption data has been measured under the conditions specied in
Standard EN50229.
• First drying should be performed with 3 kg load (the load consist: 0 sheets and 6
pillowcases and 14 towels) by selecting Cotton Dry (Cupboard) + Spin (1400);
• Second drying should be performed with 2 kg load (the load consist: 1 sheets and 3
pillowcases and 4 towels) by selecting Cotton Dry (Cupboard) + Spin (1400);
• Third drying should be performed with 2 kg load (the load consist: 1 sheets and 3
pillowcases and 5 towels) by selecting Cotton Dry (Cupboard) + Spin (1400);
(1 or 2 towels can be added or removed for setting weight.)
English 67
WD80(70)K5410OW_03744D_EN.indd 67 2016/7/22 14:39:30
Specications
Page 68
QUESTIONS OR COMMENTS?
COUNTRY CALL OR VISIT US ONLINE AT
UK 0330 SAMSUNG (7267864) www.samsung.com/uk/support
WD80(70)K5410OW_03744D_EN.indd 68 2016/7/22 14:39:30
DC68-03744D-00
Loading...