Samsung TX-P3076WH User Manual

Owner’s Instructions

DIGITAL TELEVISION

TX-P3076WH

AA68-03388A-00_eng_Cover 4/21/04 5:17 PM Page 3

Important Warranty Information Regarding Television Format Viewing

Standard screen format televisions (4:3, the aspect ratio of the screen width to height) are primarily designed to view standard format full-motion video. The images displayed on them should primarily be in the standard 4:3 ratio format and constantly moving. Displaying stationary graphics and images on screen, such as the dark top and bottom letterbox bars (wide screen pictures), should be limited to no more than 15% of the total television viewing per week.

Wide screen format televisions (16:9, the aspect ratio of the screen width to height) are primarily designed to view wide screen format full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format, or expanded to fill the screen if your model offers this feature, and constantly moving. Displaying stationary graphics and images on screen, such as the dark side-bars on non-expanded standard format television video and programming, should be limited to no more than 15% of the total television viewing per week.

Additionally, viewing other stationary images and text such as stock market reports, video game displays, station logos, web sites or computer graphics and patterns, should be limited as described above for all televisions. Displaying any stationary images that

exceed the above guidelines can cause uneven aging of picture tubes (CRTs) that leave subtle, but permanent burned-in ghost images in the television picture. To avoid this, vary the programming and images, and primarily display full screen moving images, not stationary patterns or dark bars. On television models that offer picture sizing features, use these controls to

view the different formats as a full screen picture.

Be careful in the selection and duration of television formats used for viewing. Uneven CRT aging as a result of format selection and use, as well as other burned-in images, is not covered by your Samsung limited warranty.

AA68-03388A-00_eng_Preface 4/21/04 5:13 PM Page 2

A Guide to Digital TV

What is Digital Television?

Digital television (DTV) is a new way of transmitting high quality video and audio to your TV set. Using DTV, broadcasters can transmit high definition TV (HDTV) images, Dolby digital surround audio, and new services such as multicasting (transmitting more than one program on the same TV channel) and datacasting (providing electronic program guides and interactive television). Several of these services can be combined into a single digital broadcast.

Digital Television Services

Digital Picture Quality

DTV programs are transmitted in two different formats. The first is Standard Definition Television (SDTV) and the second is High Definition Television (HDTV).

SDTV

program formats include 480-line interlaced (480i) and 480-line progressive (480p) video. 480i programs are essentially a digital version of our current analog TV programs, while the 480p format offers improved image detail over 480i. Some 480p programs are broadcast in widescreen and are comparable to progressive-scan DVD movies in image quality.

HDTV

program formats include 1080-line interlaced (1080i) and 720-line progressive (720p). Both HDTV formats are always broadcast in widescreen, and offer much higher picture quality than SDTV.

Dolby Surround Sound

With DTV, you can listen to a variety of Dolby digital audio formats from Dolby Surround 2.0 to Dolby Digital 5.1 surround, using your home audio system. Many HDTV programs are now broadcast with DD 5.1 soundtracks.

Interactive Communications and Datacasting

DTV will allow you to interact with your television; choosing programs from a detailed program guide, ordering products on-line while watching TV, and accessing ancillary data about a program.

AA68-03388A-00_eng_Preface 4/21/04 5:13 PM Page 3

How to View Digital Television

There are three ways to watch DTV. The first is to use an integrated digital TV; one with a built-in digital television tuner. The second is to connect an external DTV set-top receiver to a DTV-ready television or monitor. This type of TV or monitor will have wideband component video and stereo audio inputs. You can also watch DTV signals with personal computer (PC) tuner cards and computer monitors.

1. Integrated TVs versus DTV-ready TVs and monitors

The advantage of an integrated DTV set is that it can tune both analog and digital TV channels at the same time. All you'll need to do is adding an external antenna and you are ready to watch DTV.

However, integrated DTV sets are not as common as DTV-ready TVs and monitors. If you already own a DTV-ready TV with component video inputs, you can enjoy DTV broadcasts by simply adding a low-cost DTV set-top receiver and antenna.

2. Using a personal computer and monitor

There are plug-in cards available that will receive and display DTV broadcasts on your computer monitor. In addition, many computer monitors will display one or more of the DTV program formats directly. The most compatible format is 480p, which is similar to the VGA (640x480 pixel) computer display standard. You may be able to watch DTV broadcasts by connecting a computer monitor to the 15-pin jack on the rear of the settop DTV receiver.

NOTE

This television receiver supports the copy protection system regulated by DTLA (Digital Transmission Licensing Administrator). It should be noted that copy protected content may not be viewable depending on your particular connections.

AA68-03388A-00_eng_Preface 4/21/04 5:13 PM Page 4

Q&A

Is the antenna I use for existing TV reception good enough for DTV?

Over-the-air (OTA) digital TV broadcasting uses the same channels as analog TV and works well with many existing TV antennas. However, DTV broadcast channel assignments are different than analog channels. You should find out whether your local DTV broadcasts are on VHF (channels 2-13) or UHF (channels 14-69) to see if you need a different antenna.

If your DTV channels are on UHF and you already get good UHF reception, your present antenna may work fine. The same holds true for VHF DTV reception. Note that in some markets, both VHF and UHF channels are used for DTV broadcasts.

You can find out the latest DTV channel assignments for your area by browsing selected Internet web sites such as www.titantv.com , www.10000watts.com, and www.fcc.gov.

2. How difficult is it to receive DTV signals indoors?

This depends on whether your local DTV stations are running full power or not and how close your location is to the transmission tower. DTV receivers do not require as much signal as analog TV receivers to produce high-quality images and sound.

Once the DTV signal level exceeds a certain threshold at the receiver, the digital video and audio data is decoded at the same quality it was originally encoded for broadcast. This is a big advantage for DTV over analog TV - there is no noise, ghosting, static, or scratchy audio.

3. How can I connect an antenna in my townhouse, co-operative

apartment, condominium, or apartment?

The Federal Communications Commission's OTARD Rule (part of the Telecommunications Act of 1996) allows residents of condominiums, townhouse, or members of neighborhood associations to put up outside antennas for reception of broadcast TV signals as long as those antennas are not located in common areas and are no more than 12' in height.

Residents of rental units (apartments, etc) are not covered by the OTARD rules and will have to use indoor antennas to receive DTV broadcasts. It is possible that the landlord of an apartment complex can provide broadcast DTV signals via a master TV antenna system to each apartment.

4. Can I connect my DTV set-top receiver to my cable TV service?

Cable TV systems use a different method for transmitting digital TV programs that is currently incompatible with broadcast DTV set-top receivers. So you will still need to use an outdoor or indoor antenna to receive OTA broadcast DTV programs.

The good news is that you won't have to pay a monthly or per-program charge to watch OTA DTV and HDTV programs. They're free, unlike subscription satellite TV or premium cable TV. All you need is an antenna and a DTV set-top receiver to enjoy clear, sharp widescreen images and high-quality audio.

AA68-03388A-00_eng_Preface 4/21/04 5:13 PM Page 5

CONTENTS

Chapter 1: Your New Digital TV . . . . . . . . . .8

List of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Familiarizing Yourself with Your New TV . . . . . . . . . . . . . . . . . . . . . . .9

Front Panel Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Side Panel Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Rear Panel Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Chapter 2: Installation . . . . . . . . . . . . . . . . . 14

Connecting VHF and UHF Antennas . . . . . . . . . . . . . . . . . . . . . . . . .14

Antennas with 300-ohm Flat Twin Leads . . . . . . . . . . . . . . .14

Antennas with 75-ohm Round Leads . . . . . . . . . . . . . . . . . .15

Separate VHF and UHF Antennas . . . . . . . . . . . . . . . . . . . . .15

Connecting Cable TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Cable without a Cable Box . . . . . . . . . . . . . . . . . . . . . . . . . .15

Cable with a Cable Box that Descrambles

All Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Connecting to a Cable Box that Descrambles

some Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Connecting a VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Connecting an S-VHS VCR . . . . . . . . . . . . . . . . . . . . . . . . . .19

Connecting a Second VCR to Record from the TV . . . . . . . .19

Connecting a DVD Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Connecting to Y, P

, PR . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Connecting to Regular Audio and Video Jacks . . . . . . . . . . .20

Connecting a Digital TV Set-Top Box(480p/720p/1080i) . . . . . . . . . .21

Connecting to Y, PB, PR . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Connecting to DVI (Digital Visual Interface) . . . . . . . . . . . . .22

Connecting a Camcorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Connecting to a Digital Audio System . . . . . . . . . . . . . . . . . . . . . . . . .24

Connecting to an External Amplifier (Variable Audio Output) . . . . . .24

Installing Batteries in the Remote Control . . . . . . . . . . . . . . . . . . . . . .25

Chapter 3: Operation . . . . . . . . . . . . . . . . . .26

Turning the TV On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Viewing the Menus and On-Screen Displays . . . . . . . . . . . . . . . . . . . .26

Viewing the Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Viewing the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Selecting a Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Selecting the Antenna Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Memorizing the Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Selecting the Video Signal-source . . . . . . . . . . . . . . . . . . . . .29

Storing Channels in Memory . . . . . . . . . . . . . . . . . . . . . . . .30

Adding and Erasing Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Changing Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Using the Channel Buttons . . . . . . . . . . . . . . . . . . . . . . . . . .32

Using the Number Buttons . . . . . . . . . . . . . . . . . . . . . . . . . .32

Using the Previous Channel . . . . . . . . . . . . . . . . . . . . . . . . .32

Selecting Your Favorite Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

To Store Your Favorite Channels . . . . . . . . . . . . . . . . . . . . . .33

To View Your Favorite Channels . . . . . . . . . . . . . . . . . . . . . .33

Labeling the Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Picture Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Customizing the Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Using Automatic Picture Settings . . . . . . . . . . . . . . . . . . . . .36

Selecting the Color Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Sound Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Using Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Customizing the Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

AA68-03388A-00_eng_Contents 4/21/04 5:17 PM Page 6

CONTENTS

Using Automatic Sound Settings . . . . . . . . . . . . . . . . . . . . . .39

Chapter 3: Operation (Cont.) . . . . . . . . . . . .40

Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Option 1: Setting the Clock Manually . . . . . . . . . . . . . . . . . .40

Option 2: Setting the Clock Automatically . . . . . . . . . . . . . .42

Viewing an External Signal Source . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Setting the Signal Source . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Assigning Names to External sources . . . . . . . . . . . . . . . . . .45

Chapter 4: Special Features . . . . . . . . . . . . .46

Fine Tuning Analog Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Checking the Digital-Signal Strength . . . . . . . . . . . . . . . . . . . . . . . . . .47

Changing the Screen Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

DNIe

(Digital Natural Image engine) . . . . . . . . . . . . . . . . . . 49

Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Using the R.Surf Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Extra sound settings

(Auto Volume, BBE)

. . . . . . . . . . . . . . . . . . . . . . . . .52

Auto Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

BBE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Choosing a Multi-Channel Sound (MTS)

Soundtrack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

When a Digital Signal is received . . . . . . . . . . . . . . . . . . . . .54

When an Analog Signal is received . . . . . . . . . . . . . . . . . . . .55

Choosing a Digital Sound Format . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

Setting the On/Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

Setting the Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Using the V-Chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Viewing Closed Captions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

Setting Up Analog Captions (On-Screen Text Messages) . . . .64

Setting Up Digital Captions (On-Screen Text Messages) . . . .65

Menu Transparency Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

Setting the Function Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

Setting the DVI Standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Electronic Program Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

Using the Electronic Program Guide . . . . . . . . . . . . . . . . . . .71

Viewing Information about a Single Channel . . . . . . . . . . . .72

Viewing Information about Channels . . . . . . . . . . . . . . . . . .73

Remind List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74

Reminded Viewing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74

To view the Remind List . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Using WISE LINK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76

Switching to WISE LINK Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78

Selecting Image (JPEG) Files/ Music (MP3) Files . . . . . . . . . . . . . . . . .79

Picture (JPEG) Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

Rotating the Picture (JPEG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81

Picture Zoom (JPEG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82

Music File (MP3) Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83

Playback All JPEG/MP3 Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84

WISE LINK Menu Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85

Customizing Your Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . .87

Chapter 5: Troubleshooting . . . . . . . . . . . . .89

Identifying Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . .90

Cleaning and Maintaining Your TV . . . . . . . . . . . . . . . . . . . . . . . . . . .90

Using Your TV in Another Country . . . . . . . . . . . . . . . . . . . . . . . . . . .90

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90

Manufactured under license from Dolby Laboratories.

“Dolby” and the double D-symbol are trademarks of Dolby Laboratories.

AA68-03388A-00_eng_Contents 4/21/04 5:17 PM Page 7

YOUR NEW DIGITAL TV

List of Features

Your Samsung TV was designed with the latest technology. This TV is a high-performance unit that includes the following special features:

• Easy-to-use remote contr ol

• Easy-to-use on-screen menu system

• Automatic timer to turn the TV on and off

• Adjustable picture and sound settings that can be stored in the TV’s memory

• A special filter to reduce or eliminate reception problems

• Fine tuning control for the sharpest pictur e possible

• A built-in multi-channel sound decoder for stereo and bilingual listening

• Built-in, dual channel speakers

• A special sleep timer

• 16:9 letter box format available depending upon source

• Component Video Input jacks to obtain a sharper image from external sources

• DIGITAL INPUT (Digital Visual Interface) jack

• OPTICAL OUTPUT

• DNIe

(Digital Natural Image engine) Samsung’s New Technology enables an improved image with detail, contrast and white enhancement and 3D noise reduction.

• Wise Link is used to play JPEG files (*.jpg) and MP3 files (*.MP3) stored in the memory card on the TV.

Accessories

Once you have unpacked your TV, check to make sure that you have all the parts shown here. If any piece is missing or broken, call your dealer.

Chapter One

YOUR NEW DIGITAL TV

Remote Control(AA59-00359A)/ AAA Batteries(4301-000121)

Owner’s Instructions

Safety Guide Manual

Warranty Card; 2EA/ Registration Card

Ferrite core

; 2EA

(3301-001305)

Memory Card Slot Cover

(AA73-00025A)

AA68-03388A-00_eng_Chapter1 4/21/04 5:25 PM Page 8

YOUR NEW DIGITAL TV

Familiarizing Yourself with Your New TV

Front Panel Buttons

The buttons on the front panel control your TV’s basic features, including the on-screen menu. To use the more advanced features, you must use the remote control.

Memory Card Slot

Insert the memory card into the slot.

TV/VIDEO/ENTER

Press to change bet ween viewing TV programs and signals from ot her components. Also used to execute the selected item.

Press to see an on-screen menu of your TV's features.

VOL – and +

(TV mode)

Press to increase or decrease the volume. Used to adjust the selected item.

EXIT /ENTER (Wise Link mode)

Used to move to the previous menu. Used to execute the selected item.

CH and CH

Press to change channels.

MOVE

Used to move between items. You can also use these buttons in the WISE LINK mode.

POWER

Press to turn the TV on and off.

∏

Remote Control Sensor

Aim the remote control towards this spot on the TV.

”

TIMER indicator

When the TV is turned on, the TIMER indicator blinks five times. This indicator illuminates when the TIMER mode is set to the “On” position after setting the clock and ei ther the On timer or Off timer, with the remote control. Even if the power is turned off, this indicator stays lit. (Clock must be set before using this function.)

Note: You can use the Volume button on the remote control to control the volume while in Wise Link mode. (You cannot control the volume on the front control panel of TV)

AA68-03388A-00_eng_Chapter1 4/21/04 5:25 PM Page 9

YOUR NEW DIGITAL TV

Side Panel Jacks

You can use the side panel jacks to connect an A/V component that is used only occasionally, such as a camcorder or video game. (For information on connecting equipment, see page 23.)

AUDIO INPUT jacks

Used to connect the audio signals from a camcorder or video game.

VIDEO INPUT jack

Used to connect a video signal from a camcorder or video game.

SUPER VIDEO INPUT jack

S-Video signal from an S-VHS VCR or DVD player. Note: In S-Video mode, Audio Output depends what kind of audio input source is connected to the side audio input jacks (AV1).

AA68-03388A-00_eng_Chapter1 4/21/04 5:25 PM Page 10

YOUR NEW DIGITAL TV

Rear Panel Jacks

Use the rear panel jacks to connect an A/V component that will be connected continuously, such as a VCR or a DVD player.

Your TV has several input jacks, so you can connect different A/V components simultaneously (i.e., a VCR and a DVD, 2 VCRs, etc.).

For more information on connecting equipment, see page 14~24.

DVI (Digital Visual Interface) AUDIO INPUT jacks

Receives the digital audio signals from AV devices.

AUDIO-VIDEO MONITOR OUTPUT jacks

Connect to the audio/video input jacks of a recording VCR.

ˇÔ

AUDIO INPUT1, 2, 3 jacks

Connect to the audio output jacks of VCRs, DVD players and similar devices.

¨

VIDEO INPUT1, 2, 3 jacks

Connect to the video output jacks of VCRs, DVD players and similar devices (Three sets are available: Video1, Video2 and Video3).

DIGITAL VIDEO INPUT (Digital Visual Interface) jack

Receives the digital signals from a Set-top Box.

S-VIDEO INPUT jack

Connect to S-VIDEO output jacks of an S-VHS VCR or DVD player. Note: In S-Video mode, Audio Output depends what kind of audio input source is connected to the side audio input jacks (AV1).

∏

UPGRADE PORT

For service only.

”

OPTICAL OUTPUT jack

Connect to a Digital Audio component.

’

ANTENNA terminals

Two independent cables or antennas can be connected to these terminals. Use ANT A and ANT B terminals to receive a signal from VHF/UHF antennas or your cable system.

COMPONENT1, 2 (480i, 480p, 720p, 1080i) AUDIO/VIDEO INPUT jacks

Connect to the Audio & Video outputs of DVD or DTV Set-Top-Box.

AA68-03388A-00_eng_Chapter1 4/21/04 5:25 PM Page 11

YOUR NEW DIGITAL TV

Remote Control

You can use the remote control up to about 23 feet from the TV. When using the remote, always point it directly at the TV.

You can also use your remote control to operate your Set-Top Box, VCR, Cable Box and DVD. See page 87 for details.

POWER

Turns the TV on and off.

ANTENNA

Press to select ANT A or ANT B.

TV/COMP.

Press to switch the TV, COMPONENT1, 2 or DVI mode.

Number buttons

Press to select channels directly on the TV.

+100

Press to select channels over 100. For example, to select channel 121, press “+100”, then press “2” and “1”.

VOL +, VOL -

Press to increase or decrease the volume.

∏

MUTE

Press to temporarily cut off the sound.

”

GUIDE

Press to display the on-screen Electronic Program Guide (EPG).

’

Displays the main on-screen menu.

Up/Down Left/Right buttons

Press to select highlight up, down, left , or right .

W.LINK

Press to switch to or initialize the WISE LINK mode.



P.MODE

Adjust the TV picture by selecting one of the preset factory settings (or select your personal, customized picture set tings).

ROTATE

Press to rotate a JPEG image by 90 degrees.

MODE

Selects a target device to be controlled by the Samsung remote control(i.e., TV, STB, VCR, Cable box or DVD ).

PRE-CH

Tunes to the previous channel.

CH and CH (Channel Up/Down)

Press CH or CH to change channels.

TV/VIDEO

Press to display all of the available video sources (i.e., Video1,Video2, Video3, S-Video).

INFO

Press to display information about the current box settings and program.

EXIT

Press to exi t the menu.

ENTER

While using the on-screen menus, press ENTER to activate (or change) a particular item.

P.SIZE

Press to change the screen size.

S.MODE

Adjust the TV sound by selecting one of the preset factory settings (or select your personal, customized sound set tings).

P.ZOOM

Press to expand a JPEG image.

AA68-03388A-00_eng_Chapter1 4/21/04 5:25 PM Page 12

YOUR NEW DIGITAL TV

Remote Control (continued)

ADD/DEL

Press to add or erase channels in the TV’s memory.

◊

AUTO.PROG

Press to display the Memorized Channels menu.

BBE

BBE is a built-in ef fect that adds clarit y, punch and dynamics to the sound.

≠

FAV. CH (Favorite Channel)

Press to switch between your favorite channels.

–

VCR controls

Controls VCR tape functions: Rewind, Play, Fast For ward, Stop, Paus e.

REW (Rewind)

Press to rewind a tape in your VCR.

STOP

Press this button to stop a tape during play, record, rewind or fast forward. If the button is pressed during Full-Automatic play, the function will be cancelled.

PLAY/PAUSE

Press the Play/Pause but ton to play back prerecorded tapes or pause the tape.

Press to fast forward the tape in your VCR.

—

SET

Used during set up of this Samsung remote control, so that it will work compatibly with other devices (VCR, cable box, DVD.)

SLEEP

Press to select a preset time interval for automatic shutoff.

MTS (Multi-channel Television Sound)

Press to choose stereo, mono or Secondary Audio Program (SAP broadcast).

∑

R.SURF

Press the R.SURF button to automatically return to a preferred channel after a user-preset t ime delay.

DNIe

Activates DNIe (Digital Natural Image engine).

RESET

If your remote control is not functioning properly, take out the batteries and press the reset button for about 2~3 seconds. Re-insert the batteries and try using the remote control again.

AA68-03388A-00_eng_Chapter1 4/21/04 5:25 PM Page 13

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like this, see “Antennas with 300-ohm Flat Twin Leads,” below.

If your antenna has one lead that looks like this, see “Antennas with 75-ohm Round Leads,” on page 15.

If you have two antennas, see “Separate VHF and UHF Antennas,” on page 15.

Antennas with 300-ohm Flat Twin Leads

If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has 300ohm twin flat leads, follow the directions below.

Chapter Two

INSTALLATION

Place the wires from the twin leads under the screws on the 300-75 ohm adaptor (not supplied). Use a screwdriver to tighten the screws.

Plug the adaptor into the ANT A or ANT B terminal on the rear panel.

AA68-03388A-00_eng_Chapter2 4/21/04 5:24 PM Page 14

Connecting Cable TV

You can connect different cable systems to your TV, including cable without a cable box, and cable with a cable box that descrambles some or all channels.

Cable without a Cable Box

If you want to connect cable, and you do not need to use a cable box:

Plug the incoming cable into the ANT A or ANT B antenna terminal on the rear of the TV.

Plug the combiner into the ANT A or ANT B terminal on t he rear panel.

INSTALLATION

Antennas with 75-ohm Round Leads

Plug the antenna lead into the ANT A or ANT B terminal on the rear panel.

Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before connecting the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics shops).

Connect both antenna leads to the combiner.

AA68-03388A-00_eng_Chapter2 4/21/04 5:24 PM Page 15

INSTALLATION

Cable with a Cable box that Descrambles All Channels

Find the cable that is connected to the ANTENNA OUT terminal on your cable box. This terminal might be labeled “ANT OUT”, “VHF OUT”, or simply,“OUT”.

Connect the other end of this cable to the ANT Aor ANT B terminal on t he rear of the TV.

▼

This terminal might be labeled “ANT IN,” “VHF IN,” or simply, “IN.”

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-way splitter, an RF (A/B) switch, and four lengths of coaxial cable. (These items are available at most electronics stores.)

Find and disconnect the cable t hat is connected to the ANTENNA IN terminal on your cable box.

Connect this cable to a two-way split ter.

Connect a coaxial cable between an OUTPUT terminal on the splitter and the IN terminal on the cable box.

AA68-03388A-00_eng_Chapter2 4/21/04 5:24 PM Page 16

INSTALLATION

Connect a coaxial cable between the ANTENNA OUT terminal on the cable box and the B–IN terminal on the A/B switch.

Connect another cable between the other OUT terminal on the splitter and the A–IN terminal on the RF (A/B) switch.

Connect the last coaxial cable between the OUT terminal on the RF (A/B) switch and the ANT A or ANT B terminal on the rear of the TV.

After you’ve made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B switch to the “B” position to view scrambled channels. (When you set the A/B switch to “B,” you will need to tune your TV to the cable box’s output channel, which is usually channel 3 or 4.)

AA68-03388A-00_eng_Chapter2 4/21/04 5:24 PM Page 17

INSTALLATION

Connecting a VCR

These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the instructions on pages 14~17). Skip step 1 if you have not yet connected to an antenna or a cable system.

Unplug the cable or antenna from the back of the TV.

Connect the cable or antenna to the ANTENNA IN terminal on the back of the VCR.

Connect a coaxial cable between the ANTENNA OUT terminal on the VCR and the antenna terminal on the TV.

Connect a set of audio cables between the AUDIO OUT jacks on the VCR and the AUDIO jacks (AV1~AV3) on the TV.

If you have a “mono” (non-stereo) VCR, use a Y-connector (not supplied) to hook up to the left and right audio input jacks of the TV. If your VCR is stereo, you must connect two cables.

Connect a video cable between the VIDEO OUT jack on the VCR and the VIDEO jack (AV1~AV3) on the TV.

Follow the instructions in “Viewing an Ex ternal Signal Source” to view your VCR tape.

Ferrite Core

The ferrite core is used to attenuate undesired signals. When connecting cables, attach the ferrite core to the cable near the connector.

TV Rear Panel

AA68-03388A-00_eng_Chapter2 4/21/04 5:24 PM Page 18

INSTALLATION

Connecting a Second VCR to Record from the TV

Your TV can send out signals of its picture and sound to be recorded by a second VCR. To do this, connect your second VCR as follows:

Connect a set of audio cables between the AUDIO OUT jacks on the TV and the AUDIO IN jacks on the VCR. (The VCR input jacks might be either on the front or on back of the VCR.)

Connect a video cable between the VIDEO OUT jack on the TV and the VIDEO IN jack on the VCR.

Refer to your VCR’s instructions for more information about how to record using this kind of connection.

TV Rear Panel

Connecting an S-VHS VCR

Your TV can be connected to an S-Video signal from an S-VHS VCR. (This connection delivers a better picture as compared to a standard VHS VCR.)

To begin, follow steps 1–3 in the previous section to connect the antenna or cable to your VCR and your TV.

Connect a set of audio cables between the AUDIO OUT jacks on the VCR and the AUDIO IN 1 jacks on the TV.

Connect an S-video cable between the S-VIDEO OUT jack on the VCR and the S-VIDEO jack on the TV.

TV Rear Panel

An S-video cable is usually included with an S-VHS VCR. (If not, check your local electronics store.)

AA68-03388A-00_eng_Chapter2 4/21/04 5:24 PM Page 19

INSTALLATION

Connecting a DVD Player

Connecting to Y, PB, PR

The rear panel jacks on your TV make it easy to connect a DVD player to your TV.

Connect a set of audio cables between the COMPONENT1 INPUT (L, R) or COMPONENT 2 INPUT (L, R) jacks on the TV and the AUDIO OUTjacks on the DVD player.

Connect a video cable between the COMPONENT 1INPUT (Y, PB,PR) or COM- PONENT 2 INPUT (Y, PB,PR) jacks on the TV and the DVD OUT (Y, PB,PR) jacks on the DVD player.

Note: For an explanation of Component video, see your DVD player's owner's manual.

Connecting to Regular Audio and Video Jacks

Connect a set of audio cables between the AUDIO IN jacks(AV1~AV3) on the TV and the AUDIO OUTjacks on the DVD player.

Connect video cables bet ween the VIDEO OUT jack on the DVD player and the VIDEO IN jack(AV1~AV3) on the TV.

TV Rear Panel

AA68-03388A-00_eng_Chapter2 4/21/04 5:24 PM Page 20

Connecting a Digital TV Set-Top Box (480p/720p/1080i)

Connecting to Y, PB, PR

Connect the Y, PB, and PR video outputs of the set-top box to their corresponding inputs on the TV. Next, connect the Left and Right audio from the set-top box to the corresponding L and R terminals on the TV. (The connections for a typical set-top box are shown below.)

Connect a coaxial cable to the ANTENNA IN terminal on the Set-Top Box and the antenna terminal on the TV.

Connect a set of audio cables between the COMPONENT1 INPUT (L, R) or COMPONENT 2 INPUT (L, R) jacks on the TV and the AUDIO OUTjacks on the Set Top Box.

Connect a video cable between the COMPONENT 1 INPU T (Y, PB,PR) or COM- PONENT 2 INPUT (Y, PB,PR) jacks on the TV and the VIDEO OUT(Y, PB,PR) jacks on the Set Top Box.

Note: For detailed information, refer to the Set Top Box instruction manual.

INSTALLATION

TV Rear Panel

AA68-03388A-00_eng_Chapter2 4/21/04 5:24 PM Page 21

INSTALLATION

Connecting to DVI (Digital Visual Interface)

By inputting a high-bandwidth Digital Content Protection high-definition picture source to the DIGITAL INPUT jack on the TV, high-definition pictures can be displayed on the screen in their digital forms. (This DIGITAL INPUT jack is for use in the future when High-bandwidth Digital Content Protection DTV decoders, DVD players and D-VHS are put on the market.)

Notes

• The DIGITAL INPUT jack can only be used with 1080i, 720p and 480p picture signals. Set the DTV decoder DIGITAL OUTPUT jack output setting to 1080i, 720p or 480p. For detailed information, refer to the Set Top Box instruction manual.

• The DIGITAL INPUT jack is not compatible with the picture signal of a personal computer.

• Use a DVI 25-pin cable (commercially available) in order to digitally connect the TV with a

DTV Set-top box.

Connect a coaxial cable to the ANTENNA IN terminal on the Set-Top Box and the antenna terminal on the TV.

Connect a set of audio cables between the DVI INPUT(AUDIO L, R) jacks on the TV and the AUDIO OUT jacks on the Set Top B ox .

Connect a DVI cable between the DIGITAL INPUT jack on the TV and the DVI OUT jack on the Set Top Box.

TV Rear Panel

AA68-03388A-00_eng_Chapter2 4/21/04 5:24 PM Page 22

Connecting a Camcorder

The side panel jacks on your TV make it easy to connect a camcorder to your TV. They allow you to view the camcorder tapes without using a VCR. (Also see “Viewing an External Signal Source” on page 44).

Locate the A/V output jacks on the camcorder. They are usually found on the side or back of the camcorder.

Connect an audio cable between the AUDIO OUT jack on the camcorder and the AUDIO terminals on the TV.

Connect a video cable between the VIDEO OUT jack on the camcorder and the VIDEO(or S-VIDEO) terminal on the TV.

The audio-video cables shown here are usually included with a Camcorder. (If not, check your local elect ronics store.) If your camcorder is stereo, you need to connect a set of two cables.

INSTALLATION

AA68-03388A-00_eng_Chapter2 4/21/04 5:24 PM Page 23

Connecting to a Digital Audio System

There are many types of audio systems on the market today. A simplified illustration of an audio system is shown below. For more information, see your audio system owner’s manual.

If your system has an optical digital audio input, connect it to the OPTICAL OUT jack on the TV.

Be certain to remove the black cover from the optical output before inserting the cable.

If your system has a optical digital audio input , SAMSUNG recommends you use the optical digital output on the TV.

Connecting to an External Amplifier (Variable Audio Output)

The “AUDIO OUT” terminals cannot be used for external speakers. You must hook them up to an amplifier.

When an audio amplifier is connected to the “AUDIO OUT” terminals: Decrease the gain (volume) of the audio amplifier, and adjust the volume level with the volume control on the TV.

INSTALLATION

TV Rear Panel

AA68-03388A-00_eng_Chapter2 4/21/04 5:24 PM Page 24

▼

Replace the cover.

Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a long time.

The remote control can be used up to about 23 feet from the TV.

(Assuming typical TV usage, the batteries last for about one year.)

▼

Install two AAA size batteries.

Make sure to match the “+” and

“

–” ends of the batteries with the

diagram inside the compartment.

Installing Batteries in the Remote Control

Slide the back cover all the way out to open the battery compartment of the remote control.

INSTALLATION

AA68-03388A-00_eng_Chapter2 4/21/04 5:24 PM Page 25

OPERATION

Chapter Three

OPERATION

Turning the TV On and Off

Press the POWER button.

You can also use the POWER button on the front panel.

Viewing the Menus and On-Screen Displays

Viewing the Menus

With the power on, press the MENU button. The “Inpu t” menu appears on the screen. Its left side has six icons: Input, Picture, Sound, Channel, Setup and Guide.

Press the … or † but ton to move to items in the menu. Press the œ or √ button to display, change or use the selected items. Press the ENTER button to enter items in the menu.

Press the EXIT button to exit.

▼

The on-screen menus disappear from the screen after 2 minutes.

▼

You can also use the MENU, CHANNEL and VOLUME buttons on the control panel of the TV to make selections.

▼

The on-screen displays disappear after ten seconds.

Viewing the Display

The display identifies the current channel and the status of certain audio-video settings.

Press the INFO button on the remote control. The TV will display the Picture Mode, Sound Mode, MTS and Time.

Source List √ Edit Name √

T V Input

Source List √ Edit Name √

T V Input

TV11

Mono

Picture Mode : Dynamic Sound Mode : Custom MTS : Mono 12 : 00 am

AA68-03388A-00_eng_Chapter3 4/21/04 5:23 PM Page 26

OPERATION

Selecting a Menu Language

Press the ENTER but ton to select “Language”.

Press the MENU button.

Press the … or † but ton to select “Setup”, then press the ENTER button.

Language : English √ Time √ V-Chip √ Caption √ Menu Transparency : Normal √ Function Help : Off

√

DVI Standard : SMPTE √

Language : English √ Time √ V-Chip √ Caption √ Menu Transparency : Normal √ Function Help : Off

√

DVI Standard : SMPTE √

T V Setup

Press the … or † but ton to select the appropriate language, then press the ENTER button.

Press the EXIT button to exit .

Language :

Time V-Chip Caption Menu Transparency : Normal Function Help : Off

DVI Standard : SMPTE

English

Spanish French

T V Setup

AA68-03388A-00_eng_Chapter3 4/21/04 5:23 PM Page 27

OPERATION

Selecting the Antenna Input

You can connect two different signal sources by choosing the antenna input (Air or Cable).

Press the ENTER button to select “Antenna”.

Press the MENU button.

Press the … or † but ton to select “Channel”, then press the ENTER button.

Antenna : Air √ Auto Program √ Add/Delete √ Favorite Channels √ Name √ Fine Tune √ Signal Strength √

T V Channel

Antenna : Air √ Auto Program √ Add/Delete √ Favorite Channels √ Name √ Fine Tune √ Signal Strength √

T V Channel

Press the … or † but ton to select “Air” or “Cable”, then press the ENTER button.

Press the EXIT button to exit.

Antenna : Air

Auto Program Add/Delete Favorite Channels Name Fine Tune Signal Strength

T V Channel

Air

Cable

Alternate method:

Simply press the ANTENNA button on the remote control to select the signal source.

TV 3

AA68-03388A-00_eng_Chapter3 4/21/04 5:23 PM Page 28

+ 64 hidden pages