Hanwha Techwin America
500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666
Toll Free +1.877.213.1222 Direct +1.201.325.6920
Fax +1.201.373.0124
www.hanwhasecurity.com
PUBLIC VIEW MONITOR
User Guide
SMT-3211PVM-PIP & SMT-3211PVM
Public View Monitor
User Guide
Copyright
Hanwha Techwin Co., Ltd. All rights reserved.
©2018
Trademark
Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their
respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without
formal authorization.
Disclaimer
Hanwha Techwin
provided. Use of this document and the subsequent results shall be entirely on the use
right to change the contents of this document without prior notice.
Please change your password every three months to safely protect personal information and to prevent the damage of the information
theft.
Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.
Equipment shall be installed in accordance with the latest local/national codes of practice, and standards
eg :- UL 1203 Edn. 5, CSA22.2 No30-M1986 Edn1 rearmed 2012, CSA C22.2 No25-1966 rearmed 2014,
CSA C22.2 No 60065-03 Edn. 1, UL60065 Edn. 7,
makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be
r’s own responsibility.
Hanwha Techwin
reserves the
contents mechanical
CABINET
GENERAL
4
FUNCTIONAL
SPECIFICATIONS
7
CONTROLS AND
INDICATORS
8
1.3 Before You Begin 5
41.1 Scope
41.2 Safety Precautions
72.1 Functional Specifications
83.1 Connectors
93.2 Control Buttons (on the back)
103.3 Bottom Panel View (PIP model only)
103.3 LED Indication
113.4 Remote Control
113.5 Accessories
Material: Metal. Finish: Black
DIMENSIONS
Unit: mm(inch)
15.53”
2.31”
1.26”
20.26”
1.84”
30.12”
27.56”
Net Weight: 13.6Kg /30 lbs.
Shipping Weight: 17.19Kg / 37.91lbs.
Packing Dimension (W x H x D): 896x666x214mm / 35.31 x 26.25 x 8.46 inch
18.58”
7.87”
3.94”
3.94”
M4X8L(8pcs)
MECHANICAL
VESA MOUNTING
MTBF shall be 30,000 hours minimum at 90% confidence level and 100% duty cycle continuous
operation at 25 C. The calculation does not include LCD panel.
VESA Spec. of screw hole
100x100 mm
200x100 mm
M4 x 8mm
o
Use appropriate screws to mount VESA bracket (Screw hole: M4 x 5mm), failure to do so may cause
serious injury.
Ensure that the VESA bracket has an adequate size mounting plate, screws and/or fixings to support
the weight of the monitor and bracket to the surface to which it is being attached. Failure to do so may
cause serious injury.
If there is any doubt of the suitability of a mount or fixing method, a qualified technician should
be consulted.
Caution
This 21.5” / 27” PVM is intended to be fixed to a surface during use. Use a bracket
rated for the weight of the unit. Follow the bracket instructions for fixing to a surface.
19
regulatory agency
SAFETY APPROVALS
This series design shall meet the standards of the following domestic and foreign agencies:
UL : UL 60950-1
EMI/EMS EMISSION APPROVALS
This series design shall meet following EMI/EMS specifications:
FCC Compliance: FCC Rules and Regulations, Part 15, subpart B, Class A.
OSD MENU
12
REGULATORY AGENCY
& RELIABILITY
17
MECHANICAL
18
4.1 Hot Key
4.2 Main Menu
4.3 Main Adjust
4.4 Color Adjust
4.5 Scan Setting
4.6 Image Adjust (VGA Only)
4.7 Information
4.8 Language
4.9 Setup Menu
4.10 Source Trigger
4.11 Factory Reset
4.12 Audio Control
4.13 Banner Function
185.2 EMI/EMS Emission Approvals
12
12
12
13
13
14
14
15
15
16
16
16
17
185.1 Safety Approvals
196.1 Cabinet
196.2 Dimensions
196.3 VESA mounting
CONTENTS
18
general
OSD menu
SCOPE
This document is used to define the performance of the LCD Public View Monitor (PVM) series. The system
supports HDMI and PC inputs, as well as from the built-in camera. The On Screen Display (OSD) menu
makes the system easy to operate.
SAFETY PRECAUTIONS
Do not modify the three-prong grounding type monitor power plug in any way.
1.
2.
Operate this unit only from the type of power source indicated on the label.
3.
Do not block or cover ventilation openings on the back or bottom of the monitor cabinet.
4.
Do not place this monitor near a radiator or heating vent.
5.
Do not push objects of any kind through cabinet openings. This may result in fire or electrical shock.
6.
Before adding attachments always ask a service technician to perform routine safety tests to determine
that equipment is in safe operating condition. Ground potential tests should be part of the routine safety
check made by the service technician.
7.
Do not place monitor on an unstable cart, stand, or shelf where it may fall and injure personnel or
damage equipment.
8.
Route power cords so that they cannot be walked upon or tripped over. Do not allow anything to rest on
the power cord.
9.
Do not install monitor in wet areas, or where it may be exposed to rain or water. Do not spill liquid of any
kind on the unit.
10.
Unplug the power cord from the unit before cleaning the display. Use only a damp cloth. Do not use
alcohol, spirits, or ammonia to clean the display. DO NOT ATTEMPT TO CLEAN THE INTERIOR OF
THIS UNIT- THIS ACTION MUST BE PERFORMED BY THE SERVICE TECHNICIAN AS REQUIRED
DURING NORMAL MAINTENANCE.
11.
Refer all servicing to qualified service personnel. REMOVAL OF BACK COVER BY UNAUTHORIZED
PERSONNEL MAY EXPOSE THE USER TO DANGEROUS VOLTAGES OR OTHER HAZARDS.
12.
Unplug the unit immediately and notify the service technician.
A.
If liquid has been spilled into the display or the display has been exposed to rain or water.
B.
If the unit has been dropped or the cabinet damaged.
C.
If fuses continue to blow.
D.
If the power cord is damaged or frayed.
E.
If a distinct change from normal operation is apparent.
When replacement parts are required, be sure that the service technician uses components specified by the
manufacturer which have the same characteristics as the original parts. UNAUTHORIZED SUBSTITUTIONS
MAY RESULT IN FIRE, ELECTRICAL SHOCK OR OTHER HAZARDS.
Upon completion of any service or repairs, ask the technician to perform safety checks to determine that the
equipment is in safe operating condition.
WARNING: SERIOUS SHOCK HAZARDS EXIST WITHIN THE COVERS OF THIS MONITOR. DO NOT
OPEN THE COVERS UNDER ANY CIRCUMSTANCES,
THERE ARE NO USER SERVICEABLE COMPONENTS INSIDE
4
BANNER FUNCTION
ABC RETAIL
XYC RETAIL
1. Press / KEY to select an icon
2. Press / KEY to selection and adjust the
value
3. Press EXIT KEY button to return
BANNER POSITION – Select Banner Position TOP /
BOTTOM
BANNER ACTION – Select Banner Action OFF/
Blinking/Switching
INTERVAL DWELL – Set Banner on Dwell Timer 1~5 sec.
INTERVAL DELAY – Set Banner off Time 1~5 sec.
SELECT BANNER 1 – Select Banner 1 Type
SELECT BANNER 2 – Select Banner 2 Type
EXIT – Press OK KEY to return to the main menu
OSD MENU
17
OSD menu
SOURCE TRIGGER
Press OK KEY to enter the sub-menu
1. Press / KEY to select an icon
3. Press / KEY to selection and adjust the
value
4. Press EXIT KEY to return
TRIGGER – Select trigger OFF/MOTION
EVENT SOURCE – Select Motion event
source HDMI/VGA
EXIT – Press OK KEY to return to the main
menu
FW. UPDATE (USB) – Plug USB with update
FW then select this icon to update PVM FW
FACTORY RESET
Press OK KEY to reset PVM Monitor to factory default setting.
AUDIO CONTROL
Press OK KEY to enter the sub-menu
1. Press / KEY to select an icon
2. Press / KEY to selection and adjust the
value
3. Press EXIT KEY to return
VOLUME – Adjust the PVM Monitor volume.
MUTE – Select Audio MUTE ON/OFF.
EXIT – Press OK KEY to return to the main
menu.
BEFORE YOU BEGIN
Read these instructions before installing or operating this product.
Note: This installation should be made by a qualified service person and should conform to local codes.
This manual provides installation and operation information. To use this document, you must have the
following minimum qualifications:
A basic knowledge of CCTV systems and components
A basic knowledge of electrical wiring and low-voltage electrical connections
Intended use
Only use this product for its designated purpose; refer to the product specification and
user documentation.
Customer Support
For assistance in installing, operating, maintaining and troubleshooting this product refer to this
document and any other documentation provided.
Conventions Used in this Manual
Boldface or button icons highlight command entries. The following WARNING, CAUTION and Note
statements identify potential hazards that can occur if the equipment is not handled properly:
* WARNING:
Improper use of this equipment can cause severe bodily injury or equipment damage.
** Caution:
Improper use of this equipment can cause equipment damage.
Note: Notes contain important information about a product or procedure.
All lead-free products offered by the company comply with the requirements of the European
!
* This symbol indicates electrical warnings and cautions.
** This symbol indicates general warnings and cautions.
WARNINGS AND CAUTIONS:
To reduce the risk of fire or electric shock, do not insert any metallic objects through
the ventilation grills or other openings on the equipment.
WARNING:
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
law on the Restriction of Hazardous Substances (RoHS) directive: 2011/65/EU, which means
our manufacture processes and products are strictly “lead-free” and without the hazardous
substances cited in the directive.
The crossed-out wheeled bin mark symbolizes that within the European Union the product
must be collected separately at the product end-of-life. This applies to your product and any
peripherals marked with this symbol. Do not dispose of these products as unsorted
municipal waste.
GENERAL
16
5
general OSD menu
WARNINGS AND CAUTIONS:
To reduce the risk of fire or electric shock, do not insert any metallic objects through the ventilation grills or other openings on
the equipment.
WARNING
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate measures.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
LANGUAGE
Press OK KEY to enter the sub-menu
SETUP MENU
Press OK KEY to enter the sub-menu
1. Press / button to select an icon
2. Press OK KEY to confirm the selection and
return.
1. Press / KEY to select an icon
2. Press / KEY to selection and adjust
the value
3. Press EXIT KEY to return
OSD TIMEOUT – Adjust the OSD timeout 5~60
sec/OFF.
OSD BLENDING – Select OSD blending
LOW/MIDDLE/HIGH/OFF
BACKLIGHT CONTROL – Select backlight control
TIMER/SENSOR/OFF
BACKLIGHT TIMER – Set backlight timer
10min~120min, 10min increment/click
POWER INDICATOR LED – Select Power Indicator
LED ON/FLASH
POWER LED COLOR – Set LED color BLUE or RED
or RED+BLUE
SOURCE TRIGGER – Press OK KEY to enter the
sub-menu
OSD MENU
6
15
OSD menu
functional specifications
IMAGE ADJUST (VGA ONLY)
Press OK KEY to enter the sub-menu
INFORMATION
Press OK KEY to enter the sub-menu
1. Press / KEY to select an icon
3. Press / KEY to selection and adjust the
value
4. Press EXITY KEY to return
AUTO ADJUST – Press OK KEY to auto
adjust Image Settings
H. POSITION – Adjust the horizontal position
value manually
V. POSITION – Adjust the vertical position
value manually
PHASE – Adjust the phase value manually
CLOCK – Adjust the clock value manually
EXIT – Press OK KEY to return to the
main menu
Power Supply
PVM Monitor Power Requirements:
Voltage: DC 24V
Current: 1.8A max
Use only a PSU rated at 24Vdc with a minimum current rating of 1.8A
D-SUB Input
Analog RGB: 0.707Vrms
Support VESA Standard Timing
HDMI Input - HDMI Compatible Interface
480i / 480p / 576i / 576p
720p / 1080i / 1080p
Audio Input
Signal Level: 1.0Vrms
Environmental
Temperature:
Operating: 0
Storage: -20oC to +60oC
Humidity:
Operating: 10% to 85% (non-condensing)
Storage: 10% to 95% (non-condensing)
EDID
This series of displays support EDID (HDMI & VGA input)
o
C to +40oC
GENERAL & FUNCTIONAL SPECIFICATIONS
14
7
controls & indicators OSD menu
CONNECTORS
DC In
(A)
RJ45
(B)
ALARM IN
(C)
A. DC IN: 2.5.mm x 5.5mm
DC power connector (DC 24V Input)
B. RJ45: Ethernet (from Hanwa camera)
C. ALARM IN: Alarm input from Hanwha Camera
D. AUDIO IN: Firmware update
E. USB: FW Update
F. HDMI: HDMI input
G. D-SUB 15pin: VGA input
F. HDMI/PIP: PIP HDMI input.(PIP Model only)
AUDIO IN
(D)
USB
(E)
HDMI
(F)
D-SUB
(G)
HDMI/PIP
(H)
COLOR ADJUST
Press OK KEY to enter the sub-menu
SCAN SETTING
Press OK KEY to enter the sub-menu
1. Press / KEY to select an icon
2. Press / KEY to selection and adjust the
value
3. Press EXIT KEY to return
COLOR TEMP – Select the color temperature USER/
6500K / 7500K / 9300K
RED – Adjust the RED value under USER setting
GREEN – Adjust the GREEN value under USER setting
BLUE – Adjust the BLUE value under USER setting
COLOR RANGE – Select the color range 16~235/0~255
EXIT – Press MENU button to return to the main menu
1. Press / KEY to select an icon
2. Press / KEY to selection and adjust the value
3. Press EXIT KEY button to return
ASPECT RATIO – Select aspect ratio Normal/16:9/4:3
UNDERSCAN – Select underscan ON/OFF/USER
H.START – Adjust horizontal start value under USER setting
H.SIZE – Adjust horizontal size value under USER setting
V.START – Adjust vertical start value under USER setting
V.SIZE – Adjust vertical size value under USER setting
UPSIDE DOWN – Select the image upside down ON/OFF
EXIT – Press OK KEY to return to the main menu
OSD MENU
8
13
OSD menu controls & indicators
HOT KEY
VOLUME : Press / KEY to
adjust the volume.
KEY LOCK : Press
remote control KEY
LOCK to enable this
function.
MAIN MENU
Press MENU KEY to enter the sub-menu
MAIN ADJUST
Press OK KEY to enter the sub-menu
KEY UN-LOCK : Press
remote control KEY
LOCK again to disable
this function.
Main Adjust
Color Adjust
Scan Setting
Image Adjust
Information
Language
Setup Menu
Factory Reset
Audio Control
Exit
Press / KEY to select an icon, then press
OK KEY to confirm the selection.
1. Press / KEY to select an icon
2. Press / KEY to selection and adjust the
value
3. Press EXIT KEY button to return
VIVID MODE – Select Vivid mode
BRIGHTNESS – Adjust the brightness value
CONTRAST – Adjust the contrast value
SHARPNESS – Adjust the sharpness
SATURATION – Adjust the saturation
NR – Set Noise Reduction level OFF/LOW/MIDDLE/HIGH
DLC – Set Dynamic Luminance Control ON/OFF
EXIT – Press OK KEY to return to the main menu
CONTROL BUTTON (ON THE BACK)
A
B
C
D
E
(A) “ ” Source button
Press the button to show source menu. Select VGA, HDMI, and CAMERA input.
(B) “ ” Up button
Press the buttons to scrolling the cursor to desired function.
Press the buttons to increase the value of selected function in sub OSD menu.
(C) “ ” Down button
Press the buttons to scrolling the cursor to desired function.
Press the buttons to decrease the value of selected function in sub OSD menu.
(D) “ ” Menu button
Press the button to show the OSD main menu.
As a confirmation key during the OSD operation.
(E) “ ” Power button
Press the button to turn ON or turn OFF the monitor.
Camera Reset
Access Door
Camera SD Card
Access Door
CONTROLS & INDICATORS
12
9
controls & indicators
BOTTOM PANEL VIEW (PIP MODEL ONLY) REMOTE CONTROL
POWER KEY: Monitor Power On/Off.
MUTE KEY: Mute the Audio.
SOURCE KEY: Select input signal.
KEY: OSD scrolling the cursor to desired function.
OK KEY: Confirmation key during the OSD operation
EXIT KEY: Exit the OSD menu
MENU KEY: Monitor OSD control
CAMERA KEY: Select camera mode
KEY LOCK: Monitor KEY LOCK
VGA: Select VGA input
1. POWER LED : This red LED illuminates when power on
2. OUTPUT LED : This red LED illuminates when the PIP HDMI output
3. N1 LED : This red LED illuminates when the Camera video is selected as main
image
4. N2 LED : This red LED iluminates when the HDMI/PIP is selected as main
image
5. SOURCE : Press the button to select the input source as main
6. MODE : Press the button to select display mode
7. POSITION : Press the button to select the position of sub image when in PIP
mode
8. SIZE : Press the button to select the size of sub image when in PIP mode
7. RESOLUTION : Press the button to select the output resolution
LED INDICATION
Notes:
The remote control requires 2xAAA batteries. Ensure batteries are inserted in the correct polarity
according to the + and – symbols in the battery compartment.
To avoid damage from possible battery leakage, remove the batteries if you do not plan to use the
remote control handset for an extended period of time.
Batteries should last more than 2 years with normal use.
HDMI: Select HDMI input
SWAP : Swap camera video & HDMI/PIP input source, (PIP
Model only)
: Select PIP size & PIP position and Sequential Display Dwell
time setting.(PIP Model only)
MODE : Select MODE 1 (One view mode), MODE 2 (PIP mode),
MODE 3 (POP mode A), MODE 4 (POP mode B) & Sequential
Display. (PIP Model only).
CONTROLS & INDICATORS
A B C
(A) Light sensor: (measures ambient light for auto adjust settings)
(B) IR Receiver: (for remote control)
(C) LED: ON - GREEN/FLASH GREEN / FLASH RED. (Programmable from
OSD menu);
OFF - RED
10
ACCESSORIES
All of the accessories listed below are included with the PVM.
1. Remote Control x 1
2. DC Terminal x 1
3. AAA battery x 2
4. User’s Manual x 1
5. M4 x10mm Bolts x 5
6. Self-adhesive wire tiedown x 1
7. Screw M3 x 6mm x 1
11
Loading...