Samsung SHR-4081P User Manual

8 Channel DVR

SHR-4081N/P User’s Manual

Please be sure to keep the following in mind for the right use of the product to pre-vent proprietary risk or damage.

■ Do not use multiple plugs at once.

● This may cause abnormal heat generation or fire

■ Do not put a vase, flowerpot, cup, cosmetics, medicine, or vessel

with water around you.

● This may cause fire.

■ Do not bend the power cord forcibly nor put a heavy material on it.

● This may cause fire.

■ Do not touch the power plug with wet hands.

● This may cause electric shock.

■ Insert the power plug firmly enough not to shake.

● This imperfect connection may cause fire.

■ Keep the product off humidity, dust, or soot.

● This may cause fire or electric shock.

■ Do not put metals(coin, hair pin, metal piece, etc.) or inflammable

materials(match, paper, etc.) in the ventilation hole.

● This may cause fire.

■ Keep the surrounding temperature between 0˚C to 40˚C and keep the

product off humidity.

● This may cause breakdown.

■ Secure sufficient ventilation.

● This may cause abnormal operation due to high temperature.

■ Keep the product off direct ray of light or heat from the heating

device

● This may cause fire.

■ Do not disassemble, repair, or remodel the product.

● This may cause fire, electric shock, or injury due to abnormal operation.

■ Do not pull out the power cord.

● This may destroy the power cord, eventually, cause fire or

electric shock.

■ Plug out in the event of thunder or lightning.

● This may cause fire.

■ Keep your children off the battery after you take it out of the product.

They tend to swallow it unconsciously.

● If your children swallow it, please see the doctor immediately.

■ Install the product at a safe place or attach the product to the wall or

ceiling with a stand firmly enough not to fall to the ground.

● This may injure people.

Safety Regulations

SHR-4081N/P USER’S MANUAL

iii

WARNING

[Battery] As wrong exchange of the battery in SHR-4081N/P may cause explosion, you shall use the certified battery for SHR-4081N/P. The battery specification is as follows.

-Normal Voltage: 3V

-Normal Capacity: 220mAh

-Continuous Standard Load: 0.2mA

-Operating Temperature: -30 ~ +60˚C

[System Shutdown]

- Power-off without terminating the system in the System Shutdown menu may incur

improper motion like data loss and disk failure. Power-off shall be done in the System Shutdown menu.

This User’s Manual describes the basic usage of SHR-4081N/P. This Manual contains all the matters necessary for using SHR-4081N/P such as brief instruction, part name, function, connecting other equipment, and menu setup of SHR-4081N/P.

- SEC retains the copyright on this User’s Manual.

- This User’s Manual cannot be copied without SEC’s prior written approval.

- We are not liable for any or all losses to the product incurred by your use of nonstandard product or violation of User’s Manual.

- If you want to open the system case to touch the inside, please consult with an expert who works for the shop where you bought the product.

- You may download open source codes from the following website. (See CCTV Part of http://www.sec.co.kr)

Before we start

Standards Approvals

Note : This equipment has been tested and found to comply with the limits for a

Class Adigital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance whit the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Safety Regulations

Before we start

Standards Approvals

Chapter 1 Overview

1. Introduction

2. Features

3. Part Names and Functions

Chapter 2 Installation

1. Installation Environment Setup

2. Checking Product & Accessories

3. Additional HDD Installation

Chapter 3 Connecting with Other

Equipment

1. Connecting Video, Audio, & Monitor

2. Connecting Network

3. Connecting IEEE1394 Device

4. Connecting USB Device

5. Connecting Alarm Input/Output

6. Connecting RS-485 Device

Chapter 4 Live

1. System Motion

2. Live Screen Mode

3. Live Channel Selection and Audio On/Off Setup

4. Freeze and Zoom

5. Event Monitoring

6. Spot-out Monitoring

iii

1-1 1-2 1-3

2-1 2-2 2-3

3-1 3-2 3-3 3-5 3-6 3-8

4-1 4-2 4-5

4-6 4-7 4-8

Chapter 5 Menu Setup

Before Use

1. System

2. Camera

3. Monitoring

4. Record Mode

5. Event Record Mode

6. Record Schedule

7. Backup

8. Network

9. Network Setup

Chapter 6 PTZ Device Control

1. PTZ device Control Mode

2. Basic Operation of PAN, TILT, & ZOOM

3. PRESET Setup

4. Camera Menu Setup

5. Preset View

6. Other Views

Chapter 7 Recording

1. PANIC (Emergency Recording)

2. REC (Normal Recording)

3. Record Schedule

4. Event Recording

Chapter 8 Search & Play

Before Use

1. Calendar Search

2. Event Search

3. Date/Time Search

4. Go to First Search

5. Go to Last Search

6. Play

5-1

5-2 5-12 5-16 5-18 5-19 5-24 5-26 5-28 5-32

6-1

6-3

6-4

6-6

6-7

6-8

7-1

7-2

7-3

7-4

8-1

8-2

8-3

8-4

8-5

8-6

8-7

Chapter 9 Backup and Backup Search

1. Backup

2. Backup Search

Chapter 10 Smart Viewer

1. Introduction

2. Feature

3. PC Specification(Recommendation)

4. Smart Viewer Installation

5. Smart Viewer Program Execution

6. Smart Viewer Initial Screen

7. Monitoring Mode

8. Search Mode

9. SETUP MODE

Backup Viewer

1. Introduction

2. Features

3. PC Specification(Recommendation)

4. Backup Viewer Installation

5. Executing Backup Viewer Program

6. Initial Screen of Backup Viewer

7. Using Backup Viewer

Appendix

1. Product Specification

2. HDD Specifications

3. Outline Drawing

4. Factory Default

SHR-4081N/P Smart Viewer Play Frame Specification

6. Troubleshooting(FAQ)

9-1

9-4

10-1 10-2 10-3 10-4 10-7 10-8 10-9

10-23 10-30

11-1 11-2 11-3 11-4 11-8 11-9

11-10

12-1 12-4 12-5 12-6 12-8 12-9

Chapter 1

Overview

Introduction

1-1

The Digital Video Recorder(DVR) compresses the camera input data from 8 channels into a MPEG4 video file and the voice input data into a G.726 audio file respectively to record them in the Hard Disk or retrieve them from the Hard Disk simultaneously. In addition, it transmits the video or audio file out through a network on real time basis so that you can monitor either file remotely by your PC.

SHR-4081N/P USER’S MANUAL

Features

1-2

■ 8 CH Composite Input Connectors

■ NTSC/PALVideo Source Compatible

■ Able to record the CIF size (NTSC : 352 x 240 / PAL: 352 x 288) video image at

the speed of 240ips(NTSC) / 300ips(PAL)

■ 8 CH Loop Through Video Connectors

■ Hard Disk Overwrite Mode

■ Large quantity HDD backup function by using IEEE1394 and USB2.0, USB2.0

Memory, Backup function by using an external CD/DVD writer.

■ Able to record, play, and transmit both audio and video files to Windows Network

Viewer(Smart Viewer) simultaneously

■ Able to reacord and replay 8 channels of Audio

■ Variable Search Mode (Time/Date, Event, Camera)

■ Variable Recording Mode (Time Lapse, Event, Schedule, Emergency)

■ Extended Hard Disk Connection (IEEE1394, USB2.0)

■ Alarm Interface (Input:8, Output:4, Reset:1)

■ Remote Monitoring by Windows Network Viewer(Smart Viewer)

SHR-4081N/P USER’S MANUAL

Part Names and Functions

1-3

Function

Channel Button

Power LED

Network LED

Backup LED

HDD Access

LED

Split Screen

Selection

Button

Mode Selection

Button

REC Button

Display

Mode

Audio Setup

Button

Displays power on/off condition. Displays both network connection and data transmis-

sion conditions. Displays Backup Mode. Indicates Normal Access to HDD.

Upon Access to HDD, LED repeats on and off. Selects Single Channel in the Display Mode.

Used for Number Input Button in the Number Input Mode.

Recording starts as set in the Normal Record Mode while LED is on.

...

1 8

MODE

REC

Audio On/Off setup during play mode.

9 Displays Split Screen.

8 Displays Split Screen.

4 Displays Split Screen. 6 Displays Split Screen.

7 Displays Split Screen.

Displays PIP(Picture In Picture) Screen.

Screen change Mode : Enters Single Channel Screen by the time set in MENU.

4 Displays Split Screen. Displays the selected channel

in Full Screen. Displays both LIVE Channel and

Play Channel in PIP Screen simultaneously.

9 Displays Split Screen.

Name

1-4

PANIC Button

REC LOCK

Button

PANIC

REC LOCK KEY

No Name Function

ALARM(WIDE)

Button

MENU(PRESET)

Button

ZOOM Button

PTZ Button

SEARCH (

VIEW

)

Button

FREEZE(TELE)

Button

Direction

Control Button

Function Key

Video/Audio, set to the system, is recorded to 15 ips(NTSC)/ 12.5 ips(PAL). The image quality of video recording is very high and its size is CIF.

Locks the REC key motion.

Sets up Digital Zoom(x2).

Performs the TELE, WIDE, PRESET, and VIEW function by pressing the PTZ button.

Performs the FREEZE function in the DISPLAYMode. Performs the TELE function by pressing the PTZ.

Cancels the preset ALARM function to set up a new ALARM function

Performs the WIDE function by pressing the PTZ

Indicates the Search method. Performs the VIEW setup function by pressing the PTZ.

Displays the system setup menu or enters an upper menu. Performs the PRESET setup function by pressing the PTZ.

Changes or edits the left setup value for the detailed menu item setup. Moves the cursor up in a menu or increases the setup value for the detailed menu item setup. Changes or edits the right setup value for the detailed menu item setup. Moves the cursor down in a menu or decreases the setup value for the detailed menu item setup.

Acts as the Enter key for the menu setup.

Views the fast rewinding search screen.

Stops file searching. Toggles during playback to activate

PLAY/PAUSE or PLAY. Views the fast forwarding search screen.

Jog : Used for the Forward/Reverse

Frame search.

Shuttle : Performs the Play/Reverse Play

/FF/REW function.

PTZ

FREEZE

TELE ALARM

WIDE

VIEW

PRESET

ZOOM

¦ 





Fast

Reverse

STOP

PLAY/PAUSE

Fast

Forward

Jog/

Shuttle

JOG SHUTTLE

USB Port

A port to connect the USB type device.

SHR-4081N/P USER’S MANUAL

1-5

Caution

Do not play DVR on the carpet or other soft material to prevent clogging of the air ventilator. To play DVR on the cabinet or rack, be sure to check the ventilation condition.

No Name Function

Composite Video Signal Input Port (BNC Style Connector)

You may use THROUGH port to transmit a video signal to the other video equipment.

Audio Signal Input Port (RCA Jack) SPOT Out Output Port (BNC Style Connector)

Composite Video Signal Output Port (BNC Style Connector)

Audio Signal Output Port (RCA Jack) VGA Video Signal Output Port

S-VIDEO Video Signal Output Port Network Connection Port IEEE1394 Type Device Connection Port

- ALARM IN 1~8 : Alarm Input Port

- ALARM RESET IN : Alarm Reset Port

- ALARM OUT1~4 : Alarm Output Port

- TX+, TX-, RX+, RX- : RS-485 Communication Port

Supports the AC110-220V(NTSC) power socket.

A port to connect the USB type device.

VIDEO IN

THROUGH

AUDIO IN

SPOT

VIDEO OUT

AUDIO OUT

VGA

S-VIDEO

NETWORK

IEEE1394

ALARM

AC-IN

USB

7 8

9 10 11

Chapter 2

Installation

Installation Environment Setup

2-1

Do not play DVR on the carpet or other soft material to prevent clogging of the air ventilator. To play DVR on the cabinet or rack, be sure to check the ventilation condition.

You shall pay attention to the following before you use the product.

1. Do not use it outdoor.

2. Do not let water or liquid in the connection part or the product itself.

3. Do not impose excessive shock or force.

4. Do not pull out the power plug unreasonably.

5. Do not disassemble the product on your own.

6. Do not exceed the rated input or output range.

7. Use certified power cord only.

8. Match a product with an input ground with a power cord with a ground.

SHR-4081N/P USER’S MANUAL

Checking Product & Accessories

2-2

Upon delivery of a product, you shall unwrap the product and put it on the even floor or where you want to use it. Then you shall check if the following items are in it.

■ Main Body

■ User’s Manual

■ One Power Cord

■ Two Brackets

- Brackets are used to attach the product to the rack.

■ Smart Viewer Software CD (Incl. PDF Manual)

■ 12 Screw Specials

- Please keep screw specials well to be used for HDD addition.

■ 2 EA of RS-485/Alarm Terminal Block

Main Body

RS-485/Alarm

Terminal Block

Screw

User’s Manual

Bracket

Power Cord

SHR-4081N/P USER’S MANUAL

Additional HDD Installation

2-3

You may add up to 3 more HDDs to the product. However, since the product contains has many parts which may incur electric shock, accident, or product breakdown and improper installation or setup may disturb HDD recognition or normal product operation, you shall consult with an expert of the agency where you bought the product.

[Caution for HDD Addition]

■ Do not let the cable stuck improperly nor uncoated. (This may cause breakdown or fire.)

■ Be careful not to cut yourself by sharp edges of the product.

■ Be careful not to miss the disassembled screws or parts. Imperfect assembly due

to short of screws or parts may cause breakdown or malfunctioning.

[HDD Addition Procedure]

1.Loosen screws on both sides(5 points) and back(1 point) to detach the product cover.

2-4

2.Detach the cover from the product. (Pull out the cover slightly and lift from the back side to detach.)

3. Abracket is fixed to each side of HDD. Please loosen the screw of the bracket to

which you want to fix HDD.

BRACKET-HDD

SHR-4081N/P USER’S MANUAL

2-5

4.Pull BRACKET-HDD to the product center to detach the fixed part at the bottom to detach BRACKET-HDD from the product.

5.Tighten 4 SCREW-SPECIALs(BWH,6-32UNC,L10.5), supplied as an accessory to fix HDD to BRACKET-HDD. (Screw tighten force shall be strong enough to resist vibration.)

2-6

7.Check if BRACKET-HDD has been fixed to the product and connect both the power

supply cable and the signal transmission cable (IDE CABLE) to the HDD.

Signal Transmission

Cable (IDE Cable)

Power Supply Cable

6.Restore HDD installed BRACKET-HDD.

(Assembly shall be done in the reverse procedure of disassembly as follows. Align the 5 fixing points at the bottom with the BRACKET-HDD fixing holes respectively and push BRACKET-HDD out of the product to align the screw fixing holes. Then, tighten the screws firmly.)

SHR-4081N/P USER’S MANUAL

2-7

8.Check the connector, wiring, and cable fixing condition inside the product and close

the cover.

9.Tighten cover-fixing screws. (5 points on both sides and 1 point in the back side)

✻ You can apply 2 HDDs to each BRACKET-HDD as shown in the figure.

Attention

For HDD addition, please select the same HDD with the existing HDD fixed to the product as far as possible. This product can accept 4 more HDDs, 2 at Primary Slot and 2 at Secondary Slot respectively. Both HDDs attached to Primary Slot and Secondary Slot shall be set to Master and Slave respectively. Refer to User’s Manual for Master or Slave Jumper Setting. In the event of only one HDD installation, it shall be inserted into the Primary slot.

Note

Refer to Appendix 2 to see which HDD specifications are supplied.

2-8

Attention

! Regarding the sub fan, you need additional brackets and sub fans as follows.

The sub fan is shaped like this when viewed from the front and back. Please pay attention to the fan direction to let wind go through the fan.

@ Fix the fan as follows.

SHR-4081N/P USER’S MANUAL

2-9

# Please install the fan to be seen from the front view of the set.

2-10

$ Fixing the fan to the left.

Chapter 3

Connecting with Other

Equipment

Connecting Video, Audio,

Monitor

3-1

SHR-4081N/P USER’S MANUAL

3-2

Connecting Network

● Connecting to Internet through Ethernet(10/100BaseT)

● Connecting Internet through ADSL

Connecting IEEE1394 Device

● Connect the IEEE1394 hard disk through the back port of SHR-4081N/P.

● You can connect up to 6 IEEE1394 armored hard disks by the Daisy-Chain

method.

● After connection, Menu - System - HDD Setup is necessary for recognition and

setup for use.

● It acts as HOT PLUG to connect or disconnect the IEEE1394 device while the

system is running.

● If you press Connect/Disconnect in Menu - System - HDD Setup, HOT PLUG will

be recognized or deleted.

SHR-4081N/P USER’S MANUAL

3-3

Note

See 5-8 System (HDD Setup) of User’s Manual.

Caution

Wait until the HOT PLUG connected hard disk is stabilized enough (approx. 2 seconds per each hard disk) and click CONNECT in SHR-4081N/P MENU before use.

- Be sure to click DISCONNECT in SHR-4081N/P MENU to delete IEEE1394 Device

safely. Failure of clicking DISCONNECT may cause improper operation of IEEE1394 Device.

Caution

The IEEE1394 Device hard disk shall be set to Master.

3-4

Note

Refer to Appendix 2 to see which HDD specifications are supplied.

SHR-4081N/P USER’S MANUAL

3-5

Connecting USB Device

A total of 2 USB connecting terminals are placed in front of and behind SHR4081N/P each.

2. Connect USB HDD, USB CD/DVD, and USB Memory through the ports in front and

behind SHR-4081N/P respectively.

3. Only one USB device can be assigned to each USB connection port.

4. To recognize/ignore USB HDD, follow the procedure of Menu - System - HDD

Setup upon connecting.

5. Supply the HOT PLUG function to connect/disconnect the USB device.

6. To recognize/ignore the HOT PLUG function, press Connect/Disconnect from Menu

- System - HDD Setup.

Caution

- - After enough time is given to the stabilization of the USB device

After enough time is given to the stabilization of the USB device

connected by HOT PLUG, press Connect from SHR-4081N/P

Menu.

- - TTo disconnect the USB device, be sure to click Disconnect from

o disconnect the USB device, be sure to click Disconnect from

SHR-4081N/P

Menu. Otherwise, the USB device may be in trouble.

- - AAvailable to use with connecting the same kinds of USB device to the

vailable to use with connecting the same kinds of USB device to the

USB terminal on the front and back of SHR-4081N/P

USB terminal on the front and back of SHR-4081N/P..

(For example, 2 CD-RW or 2 USB memories can be connected to the

front and back of SHR-4081N/P

front and back of SHR-4081N/P.).)

- - If the USB memory is used, it should be set to the format supported by

If the USB memory is used, it should be set to the format supported by

SHR-4081N/P

. Although it is formatted with F

. Although it is formatted with FAA

T32 in the PC, it is re-for

T32 in the PC, it is re-for--

matted when it is connected to SHR-4081N/P

matted when it is connected to SHR-4081N/P..

Caution

- The USB device HDD shall be set to Master

- The USB device HDD shall be set to Master..

Note

Refer to User’s Manual 5-8, SYSTEM(HDD Setup).

Connecting Alarm Input/Output

3-6

The Alarm IN/OUT port in the back of SHR-4081N/P is composed of the following elements.

● ALARM IN/OUT Connection

Name Function

- ALARM IN1

- ALARM IN2

- ALARM IN3

- ALARM IN4

- ALARM IN5

- ALARM IN6

- ALARM IN7

1 - ALARM IN8

On receiving an ALARM RESET signal, the

2 - ALARM RESET IN system cancels the current ALARM input or

output signal and resumes sensing.

- ALARM OUT1

- ALARM OUT2

- ALARM OUT3

- ALARM OUT4

ALARM Output Port

ALARM Input Port

+ 164 hidden pages

Samsung SHR-4081P User Manual

Safety Regulations

Before we start

Contents