Samsung SDC5440BC User Manual

8 CHANNEL DVR

User Manual

SDS-V4040

8 Channel DVR

User Manual

Trademark

The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company.

Restriction

Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.

Disclaimer

Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user's own responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.

Design and specifications are subject to change without prior notice.

The default password can be exposed to a hacking thread so it is recommended to change the password after installing the product.

Note that the security and other related issues caused by the unchanged pa ssword shall be responsible for the user.

is the registered logo of Samsung Techwin Co., Ltd.

overview

IMPORTANT SAFETY INSTRUCTIONS

Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

! OVERVIEW

English _3

overview

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION

: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.

This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

•

To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

•

To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.

WARNING

1. Be sure to use only the standard adapter that is specified in the specification sheet.

Using any other adapter could cause fire, electrical shock, or damage to the product.

2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or

damage to the product.

3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat

generation or fire.

4. Securely plug the power cord into the power receptacle. Insecure connection may cause fire.

5. When installing the camera, fasten it securely and firmly. The fall of camera may cause personal injury.

6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on

top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.

7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.

8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately

disconnect the power source and contact the service center. Continued use in such a condition may cause fire or electric shock.

9. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this

product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair.)

10. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.

11. Do not expose the product to the direct airflow from an air conditioner.

Otherwise, it may cause moisture condensation inside the Clear Dome due to temperature difference between internal and external of the dome camera.

12. If you install this product in a low-temp area such as inside a cold store, you must seal up the wiring pipe with

silicon, so that the external air can not flow inside the housing. Otherwise, external high, humid air may flow inside the housing, pooling moisture or vapor inside the product due to a difference between internal and external temperature.

4_ overview

BEFORE START

This user manual provides Information for using the DVR such as brief introduction, part names, functions, connection to other equipment, menu setup, etc. You have to keep in mind the following notices :

• SAMSUNG retains the copyright on this manual.

• This manual cannot be copied without SAMSUNG’s prior written approval.

• We are not liable for any or all losses to the product incurred by your use of non-standard product or violation

of instructions mentioned in this manual.

• Prior to opening the case, please consult a qualified technician first. Whenever this is needed power must be removed from the unit.

• Before installing an additional HDD or connecting an external storage device (USB HDD) to this DVR, check the compatibility. Consult your provider for the compatibility list.

Warning

❖ Battery

It is essential that when changing the battery in the unit, the replacement battery must be of the same type otherwise there may be a possibility of an explosion. The following are the specifications of the battery you are using now.

• Normal voltage : 3V

• Normal capacity : 170mAh

• Continuous standard load : 0.2mA

• Operating temperature : -20°C ~ +85°C

Caution

• Connect the power cord into a grounded outlet.

• The Mains plug is used as a disconnect device and shall stay readily operable at any time.

• Batteries shall not be exposed to excessive heat such as sunshine, fire or the like

• Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According to the

Instructions.

(-4°F ~ +185°F)

CALIFORNIA USA ONLY

This Perchlorate warning applies only to primary CR (Manganese Dioxide) Lithium coin cells in the product sold or distributed ONLY in California USA.

“Perchlorate Material - special handling may apply, See www.dtsc.ca.gov/ hazardouswaste/perchlorate.”

! OVERVIEW

❖ System Shutdown

Turning off the power while the product is in operation, or undertaking improper actions may cause damage or malfunction to the hard drive or the product. Please turn off the power by right-clicking to display the context sensitive menu and select <Shutdown>. After selecting <OK> in the pop-up menu, you can pull off the power cord. You may want to install a UPS system for safe operation in order to prevent damage caused by an unexpected power stoppage. (Any questions concerning UPS, consult your UPS retailer.)

❖ Operating Temperature

The guaranteed operating temperature range of this product is 0°C ~ 40°C (32°F ~ 104°F). This product may not work properly if you run right after a long period of storage at a temperature below the guaranteed one. Prior to using a device that has been stored for a long period in low temperatures, allow the product to stand at room temperature for a period. Especially for the built-in HDD in the product, its guaranteed temperature range is 5°C ~ 55°C (41°F ~ 131°F). Likewise, the hard drive may not work at a temperature below the guaranteed one.

❖ Ethernet Port

DVR is designed for indoor use only and all the communication wirings are limited to inside of the building.

English _5

overview

CONTENTS

OVERVIEW

CONNECTING WITH OTHER DEVICE

LIVE

3 Important Safety Instructions 5 Before Start 6 Contents 8 Features 10 Part Names and Functions (Front) 11 Part Names and Functions (Rear) 12 Remote Control

14 installation 14 Checking the Installation Environment 15 Connecting the Video, Audio and Monitor 15 Connecting the USB 16 Connecting the Camera (SDC-5440BC) 19 Connecting the Network

21 Getting Started 23 Live Screen Configuration 28 Live Mode 31 Spot Out 31 Zoom 32 Audio On/Off 32 Freeze 33 Event Monitoring

6_ overview

MAIN MENU

34 System Setup 46 Setting the Device 53 Setting the Recording 57 Setting the Event 59 Backup 60 Network Configuration

SEARCH & PLAY

74 Search 77 Playback

! OVERVIEW

WEB VIEWER

BACKUP VIEWER

106

APPENDIX

109

79 Introducing Web Viewer 80 Connecting Web Viewer (Mac) 81 Using Live Viewer (Mac) 82 Connecting Web Viewer (Windows) 83 Using Live Viewer (Windows) 88 Using Search Viewer 92 Viewer Setup 103 About 104 Mobile Viewer

106 SEC Backup Viewer

109 Product Specification (Camera) 110 Product Specification (DVR) 113 Default Setting 116 Troubleshooting 119 Open Source License Report on the Product

English _7

overview

FEATURES

The DVR employs H.264 video encoding for 8 channel inputs and G.711 audio encoding for 8 channels while simultaneously supports hard disc recording and playback. These DVRs also supports network connectivity, providing remote monitoring from a remote PC transferring video and audio data.

•

Provides a convenient User Interface

•

8 CH Composite Input Connectors

•

Supports CIF(S)/2CIF(M)/4CIF(L) recording formats

•

With the network specific codec, network transfer enabled regardless of the recording conditions

•

De-interlacing processor for better picture quality

•

Display of HDD information and status by using HDD SMART

•

Hard Disk overwrite function

•

Mass storage hard disk backup through high-speed USB 2.0

•

Simultaneous Record and Playback of 8 channel video data

•

Various Search Modes (Search by Time, Event, Backup and Motion Detection)

•

Various Recording Modes (Manual, Event, Scheduled Recording)

•

Alarm Interface

•

Remote Monitoring function by Network Viewer, Smart Viewer and Mobile Viewer

Standards Approvals

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

8_ overview

Package Contents

Please unwrap the pr Please check the following contents are included in addition to the main unit.

oduct, and place the product on a flat place or in the place to be installed.

❖ Package

DVR (1SET) Ada

Remote Control (1EA) / Ba

Camera Power Ca

ble (1EA) Network Cable (1EA) Wrench, Expansion pipe and Screw (4ET)

ttery (2EA) SDC-5440BC (4SET) Camera Cable (4EA)

pter (1EA) / Power Cable (1EA) Mouse (1EA)

! OVER

VIEW

Manual CD (1EA) Quick Start Guide (1EA) W

arranty Card (1EA)

English _9

overview

PART NAMES AND FUNCTIONS (FRONT)

SDR-4101

a cb

Part Names Functions

USB Port Connects the USB devices.

a b

Remote Control Receiver

Input the remote control signal.

POWER : Displays the power ON/OFF status.

LED Indicator

All functions are operable with mouse control, since there are no front buttons.

ALARM : Lights on when an event occurs.

REC : Lights on when recording is in progress.

10_ overview

PART NAMES AND FUNCTIONS (REAR)

SDR-4101

ba c d

VIDEO IN

CH1 CH2

CH3 CH4

AUDIO IN

VIDEO IN

AUDIO OUT

9 10 11 12 13 14 15 16

5 6 7 8

4321

Part Names Functions

AUDIO IN Input ports (RCA jack) for the audio signal.

VIDEO IN Input port for the composite video signal.

SPOT BNC type of output port for the Spot signal.

VGA OUT Output port for VGA video signal.

DC 12V DVR power input port.

SPOT

87654321

VIDEO OUT

! OVERVIEW

DC 12 V

NETWORK

DC 12 V

VGA OUT

COM COM

234 5 6 7 8 G1 234 5 6 7 8 G

ALARM

RS-

ALARM IN

485

OUT

VGA OUT

SERIAL

CONSOLE

efgh

NETWORK NETWORK connector port.

VIDEO OUT BNC type of output port for the composite video signal.

AUDIO OUT Output port (RCA jack) for the audio signal.

[CONSOLE] is designed for the service repair purpose only.

If using the VGA cable, the source from VGA will be displayed as main image on the screen along with the OSD menus.

Then, the BNC port will output the video signal alone.

If not using the VGA cable, the source from BNC will be displayed as main image on the screen along with the OSD menus.

If you connect the VGA cable after the system boot, only the video signal from VGA will be displayed.

English _11

overview

REMOTE CONTROL

Displays the search menu.

Changes the screen mode.

Displays the Exit pop up screen.

Used as the numeric input keys, or displays a single

Skip Backward (by unit time),

Slow Rewind, Slow Forward,

Skip Forward (by unit time)

Goes to the system menu screen.

Up/Down/Left/Right(

Moves the cursor up/down/left/right, and runs the

Freezes the screen temporarily.

Runs the digital zoom (x2) function.

Starts or ends the live recording.

MODE

POWER

NUMBER [0~+10]

channel.

T/W

Zooms in or out.

$%_ +

)/ENTER

Select Menu.

FREEZE

ZOOM

REC

BACKUP

Displays the Backup Menu.

DVR

Activates the DVR function.

Sets the ID of the system. Select 2 digits from 0 ~ 9 while pressing the ID Key.

Move Frame

While paused, moves to the previous/next frame.

FR, STOP, PLAY/PAUSE, FF

SCROLL

Moves the menu scroll.

RETURN

Returns to the previous screen.

AUDIO

Turns Audio on/off.

ALARM

Cancels the Alarm.

REC LOCK

Selects the recording lock function.

PIP

Selects or deselects the PIP function.

Using the numeric buttons

CHANNEL 1–8 Press each button between 1 to 8. (8CH : 8)

12_ overview

Changing the Remote Control ID

1. Press the ID button of the remote control and check the ID displayed on the DVR screen.

The factory default ID of the remote control is 00.

2. Enter 2 digits of your selection in order, while pressing the system [ID] button.

3. When ID input is done, press the system [ID] button again to check the setting.

If you want to change the remote control ID to 08: Press 0 and 8 in order while the system [ID] button is pressed.

Remote control's ID and DVR’s ID should be matched for proper operation. Refer to “Remote Devices”. (Page 50)

! OVERVIEW

English _13

connecting with other device

INSTALLATION

Please take note of the followings before using this product.

•

Do not use the product outdoor.

•

Do not spill water or liquid in the connection part of the product.

•

Do not impose the system to excessive shock or force.

•

Do not pull out the power plug forcefully.

•

Do not disassemble the product on your own.

•

Do not exceed the rated input/output range.

•

Use a certified power cord only.

•

For the product with an input ground, use a grounded power plug.

CHECKING THE INSTALLATION ENVIRONMENT

Samsung Digital Video Recorder (“DVR” hereinafter) is a stateof-art security device, and contains mass storage hard disk(s) and critical circuits inside.

When the temperature rises inside the product, the product may breakdown and the product life be shortened. Please pay attention to the following recommendations before installation.

The followings are the recommendations when Samsung DVR is installed on a rack.

1. Please ensure that the rack inside is not sealed.

2. Please ensure the air is circulated through the inlet/outlet as shown in the picture.

3. If the DVR or other devices on a rack is to be stacked as in the picture, provide a suitable

space or install a ventilating opening for air circulation.

4. For natural air convection, place the inlet at the bottom of the rack and the outlet on top.

5. It is strongly recommended that a fan motor is installed at the inlet and the outlet for air

circulation. (Please fit a filter at the inlet to screen dust or foreign substances.)

6. Please maintain the temperature inside the rack or surrounding areas between

0°C ~ 40°C (32°F ~ 104°F) as shown in the figure 1.

Rack Mount Instructions - The following or similar rack-mount instructions are included with the installation instructions :

A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the

operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature specified by the manufacturer.

B) Reduced Air Flow - Installation of the equipment in a rack should be such that the

amount of air flow required for safe operation of the equipment is not compromised.

C) Mechanical Loading - Mounting of the equipment in the rack should be such that a

hazardous condition is not achieved due to uneven mechanical loading.

D) Circuit Overloading - Consideration should be given to the connection of the equipment to the supply

circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.

E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should

be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).

Temperature Unit: ºC

One Year: 24HR X 365 DAY =8,760 HR

Life (Unit: HOURS)

[Figure 1]

[Figure 2]

14_ connecting with other device

CONNECTING THE VIDEO, AUDIO AND MONITOR

CONSOLE

AUDIO IN

CH1

CH2

VGA OUT

DC 12V

NETWORK

AUDIO IN

VIDEO IN

SPOT

VIDEO OUT

CH3

CH4

AUDIO OUT

CONNECTING THE USB

! CONNECTING WITH OTHER DEVICE

1. By factory default, a USB port is provided for external connection.

2. You can connect a USB HDD, USB memory or mouse to the USB port.

3. If a USB HDD is connected to the system, recognition and settings are available in “Main Menu > Setting the

Device > Storage Device”. (Page 44)

4. This product supports hot-plugging, which connects/removes the USB device during the system operation.

If you use the USB device for Backup purposes, format it with FAT32 on PC if it is not formatted on the DVR.

English _15

connecting with other device

CONNECTING THE CAMERA (SDC-5440BC)

Equipped with the IR LED and the illumination sensor, enables you to monitor at night as well as in daytime. The camera is suitable for both internal and external use.

g f

Name Description

Camera Sunshield

Sunshield Adaptor Fixing the sunshield onto the camera.

Power Cable Used to plug the power cable.

BNC Cable BNC terminal for video signal output.

Illumination Sensor Detects incoming light to control the IR LED.

IR LED These infrared LED's are controlled by the illumination sensor.

f g

Lens

Focal length of 3.6mm enables you to cover relatively longer range of monitoring.

16_ connecting with other device

Connecting with DVR

CONSOLE

AUDIO IN

CH1

CH2

VGA OUT

DC 12V

NETWORK

AUDIO IN

VIDEO IN

SPOT

VIDEO OUT

CH3

CH4

AUDIO OUT

Installing the camera

The camera can be installed on the wall, ceiling, shelf or a desired position using the provided bracket.

1. Select a position where you want to install the camera.

Make sure the selected position can sustain the weight of the camera.

! CONNECTING WITH OTHER DEVICE

2. Use the screw bolts to mount the camera bracket onto the wall or ceiling.

• SDC-5440BC : (M4 X L20).

M4 X L20

sized screws

wall or ceiling

English _17

connecting with other device

3. Adjust the camera to target the video location by tightening camera bracket's screw and lock ring on the

camera bracket .



Left Right

Down



-180° +180°

4. Connect the camera cable to the camera.



Lock Ring

You should be careful when installing the camera outdoors because the cable connectors may be wet with moisture or pile

up with impurities.

The camera satisfies the IP66 standard, and direct exposure to water or moisture may cause problem such as

condensation.

18_ connecting with other device

CONNECTING THE NETWORK

CONSOLE

AUDIO IN

CH1

CH2

VGA OUT

DC 12V

NETWORK

AUDIO IN

VIDEO IN

SPOT

VIDEO OUT

CH3

CH4

AUDIO OUT

Connecting to network through Ethernet (10/100BaseT)

RJ-45 Ethernet Cable (Direct Cable)

Hub/Switcher

! CONNECTING WITH OTHER DEVICE

Windows Network Viewer

Back Bone

NETWORK

Hub/Switcher

English _19

connecting with other device

CONSOLE

AUDIO IN

CH1

CH2

VGA OUT

DC 12V

NETWORK

AUDIO IN

VIDEO IN

SPOT

VIDEO OUT

CH3

CH4

AUDIO OUT

CONSOLE

AUDIO IN

CH1

CH2

VGA OUT

DC 12V

NETWORK

AUDIO IN

VIDEO IN

SPOT

VIDEO OUT

CH3

CH4

AUDIO OUT

Connecting to the Network using the router

Broadband Router

External Remote PC

xDSL or Cable Modem

DDNS Server (Data Center)

Connecting to Network through ADSL

xDSL or Cable Modem

NETWORK

ADSL MODEM

RJ-45 Ethernet Cable (Direct Cable)

Phone(ADSL) Line

NETWORK

Windows Network Viewer

20_ connecting with other device

Hub/Switcher

live

GETTING STARTED

Starting the system

1. Connect the power cable of the DVR to the wall outlet.

It takes about 10 seconds to display the start screen after

booting.

2. You will see the initialization screen.

The initialization process will last about 1 minute. If a new HDD is installed, the initialization process may take longer.

3. The live screen appears with a beep.

Shutting Down the System

2012-01-01 01:10:25

! LIVE

REC

2012-01-01 01:10:25

You can shut down the system only if you have logged in to the DVR. You require permission to shut down the system if you are not logged in as admin.

1. Press the [POWER] button on the remote control or

2012-01-01 01:10:25

right-click to display the context sensitive menu and select <Shutdown>.

2. The “Shutdown” confirmation window appears.

Shutdown

3. Use the arrow keys on the remote control to move to <OK> and press the [ENTER] button or click <OK>. The system will shut down.

2012-01-01

For the permission management, refer to “Permission

Management > Setting Permissions”. (Page 41)

01:10:25

Are you sure to shutdown?

OK Cancel

English _21

live

To access a DVR or restricted menu, you should have logged in to the DVR.

1. In live mode, right-click any area of the screen.

You will see the context sensitive menu as in the right figure.

2. Click <Login>.

The login dialog appears. You can also see the login dialog to access a desired menu by pressing the [MENU] button on the remote control.

The login dialog will also appear if you press a menu button on

the remote control when the corresponding menu requires logging in.

After logged in, press [RETURN] on the remote control to display

the logout dialog.

By default, initial ID and password are set to “admin”, and “4321”.

2012-01-01 01:10:25

ID admin



Password



OK Cancel

Scene Mode

Spot Out

Audio Off

Freeze

Stop Alarm

Record

Play

Backup

Main Menu

Shutdown

Hide Launcher



The default password can be exposed to a hacking thread so it is recommended to change the password after installing

the product. Note that the security and other related issues caused by the unchanged password shall be responsible for the user.

For the restricted permission, refer to “Permission Management > Setting Permissions”. (Page 41)

Locking All Buttons

This will restrict access to all buttons available in the DVR.

1. In Live mode, press buttons on the remote control in the

order of [STOP (@)] [MENU]. All buttons will be locked.

2. In the lock condition, press any button to display a dialog

where you are prompted to enter the password for unlocking the buttons. The button lock will be released if you enter the admin password.

[FREEZE][STOP (@)][FREEZE]



2012-01-01 01:10:25

Key Lock Password

ID admin



Password



OK Cancel

22_ live

LIVE SCREEN CONFIGURATION

Icons on the Live Screen

You can check the status or operation of the DVR with the icons on the live screen.

2012-01-01 00:00:01

CAM 01

Name Description

a b

Current Date, Time Displays the current time and date.

Displayed if the zoom function is activated.

Freezes the screen temporarily.

Screen Mode

Displayed in Auto Sequence mode where all channels are switched at the specific time interval.

This icon is displayed if a user with restricted access to the Record button tries to make manual recording.

Only the user with the applicable permission can release (stop) the recording.

! LIVE

System Operation

Video Input Status

Displayed if the HDD is full and the DVR has an insufficient space to record.

Displayed if no HDD is installed or the existing HDD should be replaced.

Displayed if the HDD needs a technical examination.

This will be displayed if the backup operation is in process.

Displayed if a new firmware is found from the network.

Displayed if no input is entered in the condition that the camera is set to <ON>.

Nothing will be displayed on the screen if the camera is set to <OFF>.

English _23

live

Name Description

Camera Name/ Channel Displays the camera name and the changed channel, if any.

Displays the resolution of the recording screen. (Page 55)

Displays AUDIO ON/MUTE.

Camera Operation

Not displayed in video mode if deactivated.

Displayed if a motion detected in the condition that the motion detection is set to <ON>.

Displays the current record mode from Record/Event/Schedule.

Error Information

• If the internal HDD is not connected, the “NO HDD”( ) message will appear; if there occurs a problem, you will see the “HDD FAIL”(

) message in the top left corner. In this case, make sure you contact the

service center for assistance as this may cause a failure of recording, playback or backup.

If you see NO HDD, HDD FAIL icons on the screen, contact the service center for more details.

Live Screen Menu

In addition to the buttons on the remote control, you can access a desired menu by right-clicking the mouse any area in live mode. The context sensitive menu that appears by right-clicking the screen may differ, depending on the login/ logout, screen split mode and DVR operation mode.

24_ live

Menu items of Search, Record, Backup and Shutdown can be deactivated, depending on the user permission.

2012-01-01 01:10:25

Scene Mode

Spot Out

Audio Off

Freeze

Stop Alarm

Record

Play

Backup

Main Menu

Shutdown

Hide Launcher

Logout

< Split Mode Menu >



2012-01-01 01:10:25

Scene Mode

Spot Out

Zoom In

Audio off

Freeze

Stop Alarm

Record

Play

Backup

Main Menu

Shutdown

Hide Launcher

Logout



< Single Mode Menu >

Split Mode Menu

The context sensitive menu in split mode differs, depending on the login/logout status.

2012-01-01 01:10:25

Scene Mode

Menu Description

Scene Mode Refer to “Live Mode”. (Page 28)

Spot Out Refer to “Spot Out”. (Page 31)

Audio On/Off Refer to “Audio On/Off”. (Page 32)

Freeze Refer to “Freeze”. (Page 32)

Stop Alarm Stops the alarm output and the event monitoring. Refer to “Event Monitoring”.(Page 33)

Record/Stop Starts/stops the standard recording.

Spot Out

Audio Off

Freeze

Stop Alarm

Record

Play

Backup

Main Menu

Shutdown

Hide Launcher

Logout



! LIVE

Play Plays the search result (data). Refer to “Search & Play > Play”. (Page 77)

Search Refer to “Search & Play > Search”. (Page 74)

Backup Refer to “Main Menu > Setting the Backup”. (Page 59)

Main Menu Accesses the main menu. Refer to the Using the DVR section. (Page 34)

Shutdown

Show/Hide Launcher

Turns down the DVR.

Shows or hides the launcher. Refer to “View the Launcher Menu”. (Page 27)

English _25

live

Single Mode Menu

The single mode menu is available only in Single Mode. The context sensitive menu for the One Channel mode, in Split mode is different from that of the Single mode.

2012-01-01 01:10:25

Menu Description

Full Screen

Spot Out

Zoom In

Audio On

Freeze

Stop Alarm

Record

Play

Shutdown

Hide Launcher

Logout



Full Screen

Zoom In Enlarges the selected image. (Page 31)

Select and click a desired channel in Split mode to switch to the full screen of the selected channel.

26_ live

View the Launcher Menu

01:10:25

The Launcher menu appears on the bottom of the live screen.

1. In Live mode, right-click to display the context menu and select <Show Launcher>.

2. Move the cursor to the bottom and click a desired item in the Launcher menu.

If no input is entered for 10 seconds, the menu will disappear.

The Launcher menu can be accessed only by using the mouse.

2012-01-01

Menu Description

Date/Time

Screen Mode

b c d e hif

Displays the current time and date. The indication of AM/PM is displayed if you set 12 hours for the time format in “System >

Date/Time/Language > Time”. (Page 34)

Press this button to switch the screen mode in sequence. The current mode is highlighted in white.

2012-01-01 01:10:25

AlarmgFreeze

2012-01-01 01:10:25

! LIVE

Menu Expansion Button Click to display the hidden menu to the right.

Audio Turns ON/OFF the sound of the selected channel.

Zoom Enlarges the selected area. This is available only in Single Live mode.

Alarm Stops the alarm if it's activated.

Freeze Freezes the Live screen temporarily.

Play Enters Play mode if a file to play exist, and if not, enters Search mode.

Record Start/End recording the Live screen.

English _27

CH1 CH2

CH3 CH4

CH1CH7 CH8

CH4

CH3

CH2

CH5

CH1

CH6 CH12

CH1

CH13

CH19

CH4

CH7

CH5

CH10

CH8

CH11

CH6

CH2 CH3

CH4 CH5

CH2

CH6

CH1 CH3

CH7 CH8 CH9

CH1 CH2

CH3 CH4

CH5 CH6

CH7 CH8

CH9 CH10

CH11 CH12

CH13 CH14

CH15 CH16

CH1

CH4 CH5

CH2

CH6

CH1 CH3

CH7 CH8 CH9

CH13 CH14

CH11

CH15

CH10 CH12

CH16

CH1 CH3

CH2

CH4 CH5 CH6

CH1

CH2

CH1 CH2

CH3 CH1CH15

CH11

CH16

CH12

CH7

CH3

CH8

CH4

CH13

CH9

CH14

CH10

CH5

CH1

CH6

CH2

CH15

CH11

CH16

CH12

CH7

CH3

CH8

CH4

CH13

CH9

CH14

CH10

CH5

CH1

CH6

CH2

CH15

CH11

CH16

CH12

CH1

CH3

CH8

CH4

CH13

CH9

CH14

CH10

CH5

CH7

CH6

CH2

CH1 CH3

CH2

CH4 CH5 CH6

CH1 CH3

CH2

CH4 CH5 CH6

CH1 CH3

CH2

CH4 CH5 CH6

CH1 CH3

CH2

CH4 CH5 CH6

CH1 CH3

CH2

CH4 CH5 CH6

CH1 CH3

CH2

CH4 CH5 CH6

CH1 CH3

CH2

CH4 CH5 CH6

CH1 CH3

CH2

CH4 CH5 CH6

CH1 CH2

CH3 CH4

CH1CH7 CH8

CH1 CH3

CH2

CH4 CH5 CH6

CH1

CH2

CH1 CH2

CH3 CH4

CH1CH7 CH8

CH1 CH3

CH2

CH4 CH5 CH6

CH1

CH2

CH1CH7 CH8

CH4

CH3

CH2

CH5

CH1

CH6 CH12

CH1

CH13

CH19

CH4

CH7

CH5

CH10

CH8

CH11

CH6

CH2 CH3

CH1 CH2

CH3 CH4

CH5 CH6

CH7 CH8

CH9 CH10

CH11 CH12

CH13 CH14

CH15 CH16

CH1

CH4 CH5

CH2

CH6

CH1 CH3

CH7 CH8 CH9

CH13 CH14

CH11

CH15

CH10 CH12

CH16

CH1

CH2

CH1 CH2

CH3 CH1CH15

CH11

CH16

CH12

CH7

CH3

CH8

CH4

CH13

CH9

CH14

CH10

CH5

CH1

CH6

CH2

CH15

CH11

CH16

CH12

CH1

CH3

CH8

CH4

CH13

CH9

CH14

CH10

CH5

CH7

CH6

CH2

CH1 CH2

CH3 CH4

CH4 CH5

CH2

CH6

CH1 CH3

CH7 CH8

CH1 CH3

CH2

CH4 CH5 CH6

CH7 CH8

CH4

CH3

CH2

CH5

CH1

CH6

live

LIVE MODE

SDR-4101 display Live images from 8 channels in a total of 7 layout of split screens.

Switching the screen mode

To switch the split mode, select a screen mode in the launcher menu, or right-click to select a screen mode in the context menu. Press the [MODE] button on the remote control to switch the mode in the sequence of the launcher menu items.

CH1 CH3

CH4 CH5

CH7 CH8

9-split mode 4-split mode 6-split mode 8-split mode

CH2 CH3

CH6

CH1

CH8

Switching the split mode

SDR-4101 display 8 Live images in the sequence of Single and 4-split modes.

CH2

CH6

CH4

CH5

CH7

CH1 CH2

CH3 CH4

CH1

CH2

PIP13-split mode

CH1 CH3

CH4 CH5 CH6

CH1

Auto Sequence

CH2

CH1

CH6

CH7 CH8

CH5

CH2

CH3

CH4

28_ live

Auto Sequence

CH1

Single mode

CH1

CH1 CH2

CH3 CH4

4-split mode

1-4

5-8

In Single mode, If you have set <SEQ-Dwell Time> in “Setting the Device > Camera”, Auto Sequence will be conducted

CH1 CH3

CH2

CH4 CH5 CH6

CH1 CH2

CH3 CH4

CH1

CH1CH7 CH8

CH4

CH3

CH2

CH5

CH1

CH6 CH12

CH1

CH13

CH19

CH4

CH7

CH5

CH10

CH8

CH11

CH6

CH2 CH3

CH4 CH5

CH2

CH6

CH1 CH3

CH7 CH8 CH9

CH1 CH2

CH3 CH4

CH9 CH10

CH11 CH12

CH13 CH14

CH15 CH16

CH1

CH4 CH5

CH2

CH6

CH1 CH3

CH7 CH8 CH9

CH13 CH14

CH11

CH15

CH10 CH12

CH16

CH1 CH3

CH2

CH4 CH5 CH6

CH1

CH2

CH1 CH2

CH3 CH4

CH1CH7 CH8

CH1 CH3

CH2

CH4 CH5 CH6

CH1

CH2

CH1 CH2

CH3 CH4

CH1CH7 CH8

CH1 CH3

CH2

CH4 CH5 CH6

CH1

CH2

at the set interval. (Page 46) In a split mode, If you have set <Multi CH SEQ Time> in “Setting the Device > Monitor”, Auto Sequence will be

conducted at the set interval. (Page 51)

Manual Switching

Press the left/right button on the remote control, or click the arrow <_/+> key to move to the next split mode.

• If pressing the right [

Channel (CH 1~4)  Channel (CH 5~8)  Auto Sequence

] button in 4-split mode :

! LIVE

CH1 CH2

CH3 CH4

CH5 CH6

; ;

CH7 CH8

CH1 CH2

CH3 CH4

5-8

1-4

English _29

CH1 CH2

CH3 CH4

CH1CH7 CH8

CH4

CH3

CH2

CH5

CH1

CH6 CH12

CH1

CH13

CH19

CH4

CH7

CH5

CH10

CH8

CH11

CH6

CH2 CH3

CH4 CH5

CH2

CH6

CH1 CH3

CH7 CH8 CH9

CH1 CH2

CH3 CH4

CH5 CH6

CH7 CH8

CH9 CH10

CH11 CH12

CH13 CH14

CH15 CH16

CH1

CH4 CH5

CH2

CH6

CH1 CH3

CH7 CH8 CH9

CH13 CH14

CH11

CH15

CH10 CH12

CH16

CH1 CH3

CH2

CH4 CH5 CH6

CH1

CH2

CH1 CH2

CH3 CH1CH15

CH11

CH16

CH12

CH7

CH3

CH8

CH4

CH13

CH9

CH14

CH10

CH5

CH1

CH6

CH2

CH15

CH11

CH16

CH12

CH7

CH3

CH8

CH4

CH13

CH9

CH14

CH10

CH5

CH1

CH6

CH2

CH15

CH11

CH16

CH12

CH1

CH3

CH8

CH4

CH13

CH9

CH14

CH10

CH5

CH7

CH6

CH2

CH1 CH2

CH3 CH4

CH1CH7 CH8

CH4

CH3

CH2

CH5

CH1

CH6 CH12

CH1

CH13

CH19

CH4

CH7

CH5

CH10

CH8

CH11

CH6

CH2 CH3

CH4 CH5

CH2

CH6

CH1 CH3

CH7 CH8 CH9

CH1 CH2

CH3 CH4

CH5 CH6

CH7 CH8

CH9 CH10

CH11 CH12

CH13 CH14

CH15 CH16

CH1

CH4 CH5

CH2

CH6

CH1 CH3

CH7 CH8 CH9

CH13 CH14

CH11

CH15

CH10 CH12

CH16

CH1 CH3

CH2

CH4 CH5 CH6

CH1

CH2

CH1 CH2

CH3 CH1CH15

CH11

CH16

CH12

CH7

CH3

CH8

CH4

CH13

CH9

CH14

CH10

CH5

CH1

CH6

CH2

CH15

CH11

CH16

CH12

CH7

CH3

CH8

CH4

CH13

CH9

CH14

CH10

CH5

CH1

CH6

CH2

CH15

CH11

CH16

CH12

CH1

CH3

CH8

CH4

CH13

CH9

CH14

CH10

CH5

CH7

CH6

CH2

CH4 CH5

CH2

CH6

CH7 CH3

CH1 CH8

CH1 CH2

CH3 CH4

CH1CH7 CH8

CH1

CH13

CH19

CH4

CH7

CH5

CH11

CH2

CH6

CH1 CH2

CH3 CH4

CH9 CH10

CH11 CH12

CH13 CH14

CH15 CH16

CH2

CH6

CH1 CH3

CH2

CH4 CH5 CH6

CH1

CH2

CH1 CH2

CH1CH15

live

Channel Setting

You can display the channel in a desired area of a split screen.

1. Place the cursor over the camera name of each channel to display the <

2. Click a camera name to display a channel list where you can select a different channel.

3. Select a desired channel and click it.

The current channel will be switched to the selected one. Use the cursor to select a channel to move, and drag and drop it to a desired channel; this can also change the channel position.

Ex : if switching CH 1 to CH 7

CH1 CH3

CH4 CH5

CH7 CH8

CH2

CH6

CH7 CH3

CH4 CH5

;

CH1 CH8

CH2

CH6

> key to the right on the screen.

Switching to Single Mode

When in split mode, select and double-click a desired channel to switch to its Single mode. Press the number corresponding to a desired channel on the remote control to switch to its Single mode.

• CHANNEL 1–8 : Press each button between 1 to 8. (8CH : 8)

Ex : If double-clicking CH 3 or pressing the number “3” on the remote control.

CH2

CH1 CH3

CH4 CH5

CH7 CH8

CH6

;

CH3

30_ live

+ 100 hidden pages