Samsung SCX-RD100 User Manual

SCX-RD100

ENG

ENG FRE

COAXIAL REMOTE

CONTROLLER

user manual

imagine the possibilities

Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at

www.samsungsecurity.com

English 1

GER SPA

ITA JAP RUS CZE TUR

Safety information

C

9

2

3

4

5

6

7

8

9

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR

BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

1

1

This symbol indicates that dangerous voltage consisting a risk of
electric shock is present within this unit.

This exclamation point symbol is intended to alert the user to
the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.

WARNING

To reduce the risk of fi re or electric shock, do not expose this appliance to rain

•

or moisture.

WARNING

1.

Be sure to use only the standard adapter that is specifi ed in the specifi cation sheet.
Using any other adapter could cause fi re, electrical shock, or damage to the product.

2.

Incorrectly connecting the power supply or replacing battery may cause
explosion, fi re, electric shock, or damage to the product.

3.

Do not connect multiple controllers to a single adapter. Exceeding the capacity
may cause abnormal heat generation or fi re.

4.

Securely plug the power cord into the power receptacle. Insecure connection
may cause fi re.

5.

When installing the controller, fasten it securely and fi rmly. The fall of controller
may cause personal injury.

6.

Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or
containers fi lled with water on top of the controller. Doing so may cause personal
injury due to fi re, electric shock, or falling objects.

7.

Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fi re
or electric shock.

8.

If any unusual smells or smoke come from the unit, stop using the product. In
such case, immediately disconnect the power source and contact the service
center. Continued use in such a condition may cause fi re or electric shock.

2 – COAXIAL REMOTE CONTROLLER

Safety information

If this product fails to operate normally, contact the nearest service center. Never

9.
disassemble or modify this product in any way. (SAMSUNG is not liable for
problems caused by unauthorized modifi cations or attempted repair.)

When cleaning, do not spray water directly onto parts of the product. Doing so

10.

may cause fi re or electric shock.

CAUTION

Do not drop objects on the product or apply strong blows to it. Keep away from a

1.
location subject to excessive vibration or magnetic interference.

Do not install in a location subject to high temperature (over 50°C), low

2.
temperature (below -10°C), or high humidity. Doing so may cause fi re or electric
shock.

If you want to relocate the already installed product, be sure to turn off the power

3.
and then move or reinstall it.

Remove the power plug from the outlet when there is a lighting storm. Neglecting

4.
to do so may cause fi re or damage to the product.

Keep out of direct sunlight and heat radiation sources. It may cause fi re.

5.

Install it in a place with good ventilation.

6.

Avoid aiming the controller directly towards extremely bright objects such as sun.

7.

Apparatus shall not be exposed to dripping or splashing and no objects fi lled with

8.
liquids, such as vases, shall be placed on the apparatus.

The Mains plug is used as a disconnect device and shall stay readily operable at

9.
any time.

ENG

English 3

Important Safety Instructions

Read these instructions.

1.

Keep these instructions.

2.

Heed all warnings.

3.

Follow all instructions.

4.

Do not use this apparatus near water.

5.

Clean only with dry cloth.

6.

Do not block any ventilation openings. Install in accordance with the

7.
manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, or other

8.
apparatus (including amplifi ers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. A

9.
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong is provided for your safety. If the provided plug does not fi t into your outlet,
consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs,

10.

convenience receptacles, and the point where they exit from the apparatus.

Only use attachments/accessories specifi ed by the

11.

manufacturer.

Use only with cart, stand, tripod, bracket, or table

12.

specifi ed by the manufacturer, or sold with the apparatus.

Unplug this apparatus when a card is used. Use caution

13.

when moving the cart/ apparatus combination to avoid
injury from tip-over.

Refer all servicing to qualifi ed service personnel. Servicing is required when the

14.

apparatus has been damaged in any way, such as powersupply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.

4 – COAXIAL REMOTE CONTROLLER

Contents

Introduction

Introduction 6

Part names and functions 7

Installation

Checking Installation Environment 11

Installation precautions 11

Connection & Control

To Control the camera coaxial communications 12

To control the camera using RS-485 device
via coaxial communications 13

To control the camera using RS-232 device
via coaxial communications 14

To control the camera using RS-485 signal output 15

To control the camera using RS-485 signal
output via RS-232 communications 16

Switch Setting Table 17

Specifi cations

Specifi cations 20

Dimensions 21

ENG

English 5

Introduction

P

❶

❷

❸

❹

❖

q

r

p

o

n

INTRODUCTION

This product is a remote controller for Samsung’s CCTV cameras of New-generation
DSP, via coaxial cable not requiring additional control wirings.

Features

❖

Long-distance remote control

•

Through RS-485 communication, remote control is possible up to 1.2
kilometers.

Easy Control

•

Easy and simple 5-way keys for controlling the camera.

System’s Expandability

•

It is possible to implement an integrated system by using the system controller
(SSC-5000 or similar) through RS-485 communication.

Portability

•

Its small size and light weight maximizes the portability, as well as its power
source adopting standard battery for outdoor use.

List of controllable models

❖

You can control Samsung’s cameras supporting coaxial communications.

•

Samsung’s RS-485 supporting cameras can be controlled through RS-485

•

communication. (For supported 3rd-party protocols, refer to page 17.)

What’s Included

❖

<Controller> <User Guide>

6 – COAXIAL REMOTE CONTROLLER

G

Introduction

PART NAMES AND FUNCTIONS

Front Panel❖

ENG

n

POWER

o
p

q

r

STATUS LED

❶

- Displays the status of the current operation.

POWER LED

❷

- When the controller turns on, it will be turn light.

POWER Switch

❸

- If you slide it to ON, the controller turns on.

CABLE COMPENSATION Switch

❹

- For long distance coaxial communications, you can use this switch for amplifying

the control signal.

Cable SPEC Compensation

POWER

OFF ON

CABLE
COMPENSATION

SL

5C-HFBT

STATUS

ADDRESS

(X)100 (X)10

3

3

2

2

4

4

1

1

5

5

0

0

6

6

9

9

7

7

8

8

1ON2345678

1ON2

TERMINATION PROTOCOL

(X)1

3

2

4

1

5

0

6

9

7

8

REMOTE CONTROLLER SCX-RD100

SL

250M or less 200M ~ 500M

s

t

English 7

Introduction

ON

356

8

PROTOCOL

1ON2

❖

P

N

RS-485 TERMINATION & PROTOCOL Setting Switch

❺

- You can select to set the RS-485 termination.

- Turn this switch ON, if RS-485 termination is required.

1ON2

1ON2345678

TERMINATION

- For multi-protocol settings, you can set the protocol and baud rate, and

selection of COAXIAL/RS-485 or RS-232.

1ON2

TERMINATION

TERMINATION

PROTOCOL

1ON2345678

PROTOCOL

- Use pin 1,2,3,4 of the Protocol setting switch to select a protocol.

- Use pin 5,6 of the Protocol setting switch to select a baud rate.

- Use pin 7 of the Protocol setting switch to select COAXIAL/RS-485 output.

- Use pin 8 of the Protocol setting switch to select RS-232 input.

❻

Address Switch

-

For RS-232 / RS-485 communications, you can use this switch to set the address.

ADDRESS

(X)100 (X)10 (X)1

3

2

4

1

5

0

6

9

7

8

3

2

4

1

5

0

6

9

7

8

3

2

4

1

5

0

6

9

7

8

- Set the address by using three switches shown above.

- From the left, the number is hundreds, tens and ones place, respectively.

The effective range of valid address is between 0 and 255 (1~255 for multi­protocol).

If you specify the address as other than between 0 and 255, it will be set to 0.



NOTE

❼

Menu Navigation Key

Use this to navigate through the menus.

8 – COAXIAL REMOTE CONTROLLER

Introduction

PART NAMES AND FUNCTIONS

Rear Panel❖

ENG

- AA BATTERY

.

You can use 4 AA-sized batteries for the power.

- The average operation time is 20 hours based on the alkaline battery.

(If the battery is discharged, it can cause a distortion of the video signal, or
electric interference.)

Remove the battery if you do not use the controller for a longer period. Otherwise, it



NOTE

may cause damage to the controller from a leak of the battery solution.
Take caution not to change the specified polarity.



Do not use a new battery with an old one.



For storing used batteries, keep out of reach of children. Wasted batteries are to be



collected separately.

English 9

Introduction

RS-232C

VIDEO

DC 12VRS-485

C

N

Top❖

REMOTE CONTROLLER SCX-RD100

TX RX

1ON23456781ON2

OUT IN

TERMINATION PROTOCOL

SL

COMPENSATION

(X)100 (X)10 (X)1

CABLE

ADDRESS

OFF ON

POWER

POWER STATUS

n op qr

USB Port

❶

This terminal is used for updating the product’s fi rmware.

-

❷

RS-232 Port (9-pin D SUB)

- Used to control remotely using RS-232 communication.

❸

RS-485 Port (4-pin)

- Used to control remotely using RS-485 communication.

❹

VIDEO IN/OUT Connector (BNC)

- VIDEO IN receives coaxial communication from cameras, and VIDEO OUT

outputs the video signal.

❺

DC12V Power Connector (2-PIN)

- Used for connecting DC12V power source.

I

10 – COAXIAL REMOTE CONTROLLER

Installation

CHECKING INSTALLATION ENVIRONMENT

Please check the following instructions before installation for your safety.

•

The way of connecting the main product with external devices (COAXIAL BNC)

•

is very important to build up a proper system.

Do not disassemble the unit; doing so could expose you to dangerous high

•

voltage points.

INSTALLATION PRECAUTIONS

Make sure you turn off the product before installation.

•

Do not put a strong force on or shake the product; otherwise it may cause

•

malfunction.

Keep the product away from areas of strong magnetic fi eld or electric

•

interference, or wireless devices such as radio or TV set.

Keep clean the installation place during and after the installation.

•

An abnormal smells from the product is a sign of abnormal condition, which

•

may cause fi re or electric shock. In this case, disconnect the product from
the main power immediately and contact the retailer for technical help from
authorized servicing.

Keep the product away from a wet fl oor, do not use an unearthed power

•

extension cable, worn-out power cord, neither forget earth-grounding.

Use a dry cloth only to dirt off the product. If the product is badly dirty, apply

•

neutral detergent on a cloth that is used to dirt off, and wipe it out with a dry
cloth.

Do not use volatile substances such as alcohol, benzene or thinner as these

•

may damage the fi nish.

ENG

English 11

Connection & Control

T
V

2

3

4

5

6

N

TO CONTROL THE CAMERA COAXIAL COMMUNICATIONS

REMOTE CONTROLLER SCX-RD100

TERMINATION PROTOCOL

1ON23456781ON2

SL

COMPENSATION
CABLE

(X)100 (X)10 (X)1

OFF ON

ADDRESS

POWER

POWER STATUS

Connect the product to DC 12V power source or insert 4 AA-sized

1.

batteries into the battery compartment.

Set the protocol switch 7 to ON.

2.

Connect the VIDEO IN of the unit and VIDEO OUT of the AI Camera

3.

directly.

For proper data communication, the unit and AI camera should be connected directly.

–

(If you connect a DVR or keyboard in the middle of the main unit and AI camera,
bidirectional communication will not be established.)

Connect VIDEO OUT of the main unit to a monitor’s video input terminal.

4.

Turn the Power switch ON.

5.

When it is powered on for the fi rst time, initialization begins and the status LED blinks

–

once completed. During the initialization, no operation is enabled.

Now you can control the camera by using the menus.

6.

1

You can use the menu as following :

❖

Press and hold [ENTER]: Moves to the main menu screen.

–

Press [ENTER] briefl y: Used to confi rm the current settings.

–

Four Direction Keys: Used to move the cursor up/down or left/right.

–

For proper coaxial communication, AI camera should be set to Samsung protocol.

–

Refer to the switch settings. (See page 17)

Control of pan/tilt/zoom using the keys is not supported.

–

12 – COAXIAL REMOTE CONTROLLER

Connection & Control

TO CONTROL THE CAMERA USING RS-485 DEVICE
VIA COAXIAL COMMUNICATIONS

REMOTE CONTROLLER SCX-RD100

TERMINATION PROTOCOL

1ON23456781ON2

SL

COMPENSATION

CABLE

(X)100 (X)10 (X)1

OFF ON

ADDRESS

POWER

POWER STATUS

Connect the product to DC 12V power source or insert 4 AA-sized

1.

batteries into the battery compartment.

Set the protocol switch 7 to ON.

2.

Connect the VIDEO IN of the unit and VIDEO OUT of the AI Camera

3.

directly.

For proper data communication, the unit and AI camera should be connected directly.

–

(If you connect a DVR or keyboard in the middle of the main unit and AI camera,
bidirectional communication will not be established.)

Connect VIDEO OUT of the main unit to a monitor’s video input terminal.

4.

Connect TX(+/-) of RS-485 device to RX(+/-) of the main unit.

5.

(For a full duplex system, connect RX(+/-) of RS-485 device to TX (+/-) of
main unit additionally.)

Using RS-485 device, you can control the camera menu.

6.

For proper coaxial communication, AI camera should be set to Samsung protocol.

–

Refer to the switch settings. (See page 17)

By factory default, protocols of SAMSUNG and PANASONIC are supported.



NOTE

For additional protocols, update the following software program via the web.



Input of video signal is required to control RS-485.



ENG

English 13

Connection & Control

T
O

2

3

4

5

❖

N

TO CONTROL THE CAMERA USING RS-232 DEVICE
VIA COAXIAL COMMUNICATIONS

REMOTE CONTROLLER SCX-RD100

TERMINATION PROTOCOL

1ON23456781ON2

SL

COMPENSATION
CABLE

(X)100 (X)10 (X)1

OFF ON

ADDRESS

POWER

POWER STATUS

Connect the product to DC 12V power source or insert 4 AA-sized

1.

batteries into the battery compartment.

Set the protocol switches 7 and 8 to ON.

2.

Connect the VIDEO IN of the unit and VIDEO OUT of the AI Camera

3.

directly.

For proper data communication, the unit and AI camera should be connected directly.

–

(If you connect a DVR or keyboard in the middle of the main unit and AI camera,
bidirectional communication will not be established.)

Connect VIDEO OUT of the main unit to a monitor’s video input terminal.

4.

Connect the RS-232 device’s cable to the RS-232 port of the main unit.

5.

Using RS-232 device, you can control the camera menu.

6.

The RS-232 device is the same as RS-485 regarding the protocol setting, but

–

supports only the Samsung protocol.

For proper coaxial communication, AI camera should be set to Samsung protocol.

–

Refer to the switch settings. (See page 17)

1

RS-232 and RS-485 communications cannot be used for simultaneous input.



NOTE

14 – COAXIAL REMOTE CONTROLLER

Connection & Control

TO CONTROL THE CAMERA USING RS-485 SIGNAL
OUTPUT

REMOTE CONTROLLER SCX-RD100

TERMINATION PROTOCOL

1ON23456781ON2

SL

COMPENSATION
CABLE

(X)100 (X)10 (X)1

OFF ON

ADDRESS

POWER

POWER STATUS

Connect the product to DC 12V power source or insert 4 AA-sized

1.

batteries into the battery compartment.

Set the protocol switches 7 and 8 to OFF.

2.

Connect the RX(+/-) of the unit to the RS-485 (+/-) port of the camera.

3.

Match the camera’s address, baud rate, and protocol to the same to

4.

those of the unit.

Now you can control the camera by using the menus.

5.

You can use the menu as following :

❖

Press and hold [ENTER]: Moves to the main menu screen.

–

–

Press [ENTER] briefl y: Used to confi rm the current settings.

–

Four Direction Keys: Used to move the cursor up/down or left/right.

Control of pan/tilt/zoom using the buttons is not supported.

–

To exit the menu screen, press and hold the key again.

ENG

Input of video signal is required to control RS-485.



NOTE

The next time you access the menu, press and hold the [ENTER] key twice.



English 15

Connection & Control

S

N

❖

❖

N

TO CONTROL THE CAMERA USING RS-485 SIGNAL
OUTPUT VIA RS-232 COMMUNICATIONS

REMOTE CONTROLLER SCX-RD100

TERMINATION PROTOCOL

1ON23456781ON2

SL

COMPENSATION
CABLE

(X)100 (X)10 (X)1

OFF ON

ADDRESS

POWER

POWER STATUS

Connect the product to DC 12V power source or insert 4 AA-sized

1.

batteries into the battery compartment.

Set the protocol switch 8 to ON.

2.

Connect the RX(+/-) of the unit to the RS-485(+/-) port of the camera.

3.

Match the camera’s address, baud rate, and protocol to the same to

4.

those of the unit.

RS-232 can be controlled using the Samsung protocol alone.

–

Connect the RS-232 device’s cable to the RS-232 port of the main unit.

5.

Using RS-232 device, you can control the camera menu.

6.

RS-232 and RS-485 communications cannot be used for simultaneous input.



NOTE

For the switch settings, see the switch setting table. (See page 17)



Input of video signal is required to control RS-485.



16 – COAXIAL REMOTE CONTROLLER

Connection & Control

SWITCH SETTING TABLE

Use a combination of pin 1,2,3,4 of the Protocol setting switch to select a protocol.

❖

1ON2

1ON23456781ON234

TERMINATION

Protocol Setting Switch (0 :r, 1 :q)

Pin 1 Pin 2 Pin 3 Pin 4

0 0 0 0 SAMSUNG HALF

1 0 0 0 SAMSUNG FULL

1 1 0 0 PANASONIC HALF

0 0 1 0 PANASONIC FULL

1 1 1 0 PHILIPS HALF

1 0 0 1 KALATEL HALF

0 1 0 1 ERNA HALF

1 1 0 1 DIAMOND HALF

0 0 1 1 VCL TP HALF

By default, it is configured to support SAMSUNG and PANASONIC.



NOTE

For other protocols, you can find assistance from our website at:

PROTOCOL

Protocol HALF/FULL

HALF : half-duplex

FULL : full-duplex

http://www.samsungsecurity.com

Use pin 7 and 8 of the Protocol setting switch to set the coaxial output.

❖

PIN 7 Output Selection

1ON23456787

PROTOCOL

1ON23456788

PROTOCOL

ON COAXIAL out

OFF RS-485 out

PIN 8 RS-232 input

ON RS-232 input

OFF RS-232 No use

ENG

RS-232 and RS-485 communications cannot be used for simultaneous input.



NOTE

English 17

Connection & Control

–

See the following table to set the baud rate.

1ON2

TERMINATION

1. SAMSUNG

2. PHILIPS

3. PANASONIC

4. DIAMOND, VCL TP

 Only supports 9600 bps

1ON234567856

BAUD RATE PIN 5 PIN 6

38400 BPS OFF OFF

19200 BPS ON OFF

9600 BPS OFF ON

4800 BPS ON ON

BAUD RATE PIN 5 PIN 6

38400 BPS OFF OFF

9600 BPS ON OFF

BAUD RATE PIN 5 PIN 6

19200 BPS OFF OFF

9600 BPS ON OFF

4800 BPS OFF ON

BAUD RATE PIN 5 PIN 6

9600 BPS OFF ON

PROTOCOL

18 – COAXIAL REMOTE CONTROLLER

Connection & Control

5. ERNA

BAUD RATE PIN 5 PIN 6

2400 BPS ON ON

 Only supports 2400 bps

6. KALATEL

BAUD RATE PIN 5 PIN 6

9600 BPS OFF ON

4800 BPS ON ON

ENG

English 19

Specifi cations

D

SPECIFICATIONS

Item Description

COAXIAL

RS-232

RS-485

Environmental

Conditions

WEIGHT NET 200 g

Communication Method COAXIAL INTERFACE

Range Max. 500m (with 5C-HFBT cable)

Connector Type D-SUB 9P

Port 1 Port

BAUD RATE

Connector Type 4P Terminal Type

Port 1 Port

BAUD RATE

USB PORT(USB2.0) S/W PROGRAM UPLOAD

VIDEO IN/OUT

Operating Temp. -10˚C ~ +50˚C

Humidity Less than 90%

POWER DC12V ± 10%

DIMENSIONS (WxHxD) 150(W) X 36(H) X 102(D)

4800/9600/19200/38400bps

(Only Samsung protocol supported)

2400/4800/9600/19200/38400bps

(Supports each protocol)

Composite Video

1.0Vp-p, 75ohm,

Cable Compensation out

(Select:S/L)

20 – COAXIAL REMOTE CONTROLLER

DIMENSIONS

Specifi cations

Unit (mm)

ENG

English 21

Correct Disposal of This Product (Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking on the product, accessories or literature indicates that the product and its electronic
accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste
at the end of their working life. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local
government office, for details of where and how they can take these items for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

Correct disposal of batteries in this product

(Applicable in the European Union and other European countries with separate battery return systems.)

This marking on the battery, manual or packaging indicates that the batteries in this product should not
be disposed of with other household waste at the end of their working life. Where marked, the chemical
symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference
levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm
to human health or the environment.

To protect natural resources and to promote material reuse, please separate batteries from other types of
waste and recycle them through your local, free battery return system.

AB68-00857A