Samsung SCC-B1031P, SCC-B1331, SCC-B1331P User Manual

SCC-B1331(P)
SCC-B1031P

DIGITAL COLOR CAMERA

user manual

imagine the possibilities

Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at

www.samsungsecurity.com

ENG FRC

ENG

SPA-M

JAP

POR-B

Safety information

T

D

D

R
d

K

n

A
C

A

T

h

h

s

s

e

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates that dangerous voltage consisting a risk of electric shock is
present within this unit.

This exclamation point symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the

WARNING

To reduce the risk of fi re or electric shock, do not expose this appliance to rain or moisture.

•

To prevent injury, this apparatus must be securely attached to the fl oor/wall in accordance with the

•

installation instructions.

If this power supply is used at 240V ac, a suitable plug adapter should be used.

•

WARNING

Be sure to use only the standard adapter that is specifi ed in the specifi cation sheet.

1.
Using any other adapter could cause fi re, electrical shock, or damage to the product.

Incorrectly connecting the power supply or replacing battery may cause explosion, fi re, electric shock, or

2.
damage to the product.

Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat

3.
generation or fi re.

Securely plug the power cord into the power receptacle. Insecure connection may cause fi re.

4.

When installing the camera, fasten it securely and fi rmly. The fall of camera may cause personal injury.

5.

Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers fi lled with water on

6.
top of the camera. Doing so may cause personal injury due to fi re, electric shock, or falling objects.

Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fi re or electric shock.

7.

If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately

8.
disconnect the power source and contact the service center. Continued use in such a condition may cause
fi re or electric shock.

9.

If this product fails to operate normally, contact the nearest service center. Never disassemble or modify
this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifi cations or
attempted repair.)

When cleaning, do not spray water directly onto parts of the product. Doing so may cause fi re or electric shock.

10.

2 – DIGITAL COLOR CAMERA

appliance.

CAU

1.

2.

3.

4.

5.

6.

7.

8.

9.

FCC

This

1) T

2) T

Ca

Thi
ant
inte
Thi
in a
Op
use

e

h

If
it

I

s

ify

TS

ant

r on

se

r

k.

Safety information

CAUTION

Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to

1.
excessive vibration or magnetic interference.

Do not install in a location subject to high temperature (over 140°F), low temperature (below -14°F), or high

2.
humidity. Doing so may cause fi re or electric shock.

If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall

3.
it.

4.

Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so may cause fi re or
damage to the product.

5.

Keep out of direct sunlight and heat radiation sources. It may cause fi re.

6.

Install it in a place with good ventilation.

7.

Avoid aiming the camera directly towards extremely bright objects such as sun, as this may damage the
CCD image sensor.

8.

Apparatus shall not be exposed to dripping or splashing and no objects fi lled with liquids, such as vases,
shall be placed on the apparatus.

9.

The Mains plug is used as a disconnect device and shall stay readily operable at any time.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :

1) This device may not cause harmful interference, and

2) This device must accept any interference received including interference that may cause undesired operation.

Caution

This equipment has been tested and found to comply with the limits for a Class A digital device, pursu­ant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.

IC Compliance Notice

This Class A digital apparatus meets all requirements of the Canadian Interference.­Causing Equipment Regulations of ICES-003.

ENG

English – 3

Important Safety Instructions

WARNING

Read these instructions.

1.

Keep these instructions.

2.

Heed all warnings.

3.

Follow all instructions.

4.

Do not use this apparatus near water.

5.

Clean only with dry cloth.

6.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

7.

Do not install near any heat sources such as radiators, heat registers, or other apparatus (including

8.
amplifi ers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades

9.
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong is provided for your safety. If the provided plug does not fi t into your outlet, consult
an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and

10.
the point where they exit from the apparatus.

Only use attachments/accessories specifi ed by the manufacturer.

11.

Use only with cart, stand, tripod, bracket, or table specifi ed by the manufacturer, or

12.
sold with the apparatus.

Unplug this apparatus when a card is used. Use caution when moving the cart/

13.
apparatus combination to avoid injury from tip-over.

Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has been

14.
damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.

Apparatus shall not be exposed to dripping or splashing and no objects fi lled with
liquids, such as vases, shall be placed on the apparatus

4 – DIGITAL COLOR CAMERA

ult

and

ave

h

Contents

Introduction

Features 6

PRODUCT & ACCESSORIES 7

Part Names and Functions 8

Installation

Connecting the Auto Iris Lens Connector 11

Mounting the lens 11

Connecting cables and checking operation 12

s
ide

, or

How to use OSD Menu

Using Icons in the Menu 13

Main Menu 13

Profi le 14

Camera Setup 16

Intelligence 22

Privacy zone Setup

Other Set 24

System Information 25

Language 25

Specifi cations

Specifi cations 26

23

ENG

English – 5

Introduction

P

FEATURES

High Resolution

❖

•

This camera has realized high resolution of 600 lines using the top-notch full digital image processing and
special algorithm technologies.

Intelligent Motion Detection & Tracking

❖

•

This is an intelligent function that automatically detects a motion of an object. You can set a virtual fence so it
sounds an alert if an object passes / enters /exits the virtual fence or virtual area.

❖

XDR (eXtended Dynamic Range)

•

Actively controls the gamma compensation in the way it operates the ambient luminance contrast in a
certain pixel unit to determine the optimal visibility.

❖

High Sensitivity

•

It implements images of high sensitivity using the up-to-date SONY Super-HAD Progressive CCD.

❖

Low Illumination

It uses the digital signal technologies such as low illumination and Day/Night functions that make your camera

•

identify objects even in the worst environment.

Superior Backlight Adjustment

❖

When an object has a bright illumination or sunlight behind it, this camera automatically improves the

•

shaded object picture quality.

❖

Digital Power Synchronization

•

The full digital Line Lock function directly adjusts the vertical camera synchronization to enhance the
operationability and reliability of this camera.

❖

Output Signal Setting

You can set the following Video output signals: Image reversion (Horizontal, Vertical, or both), Privacy,

•

Horizontal/Vertical profi ling, and digital zooming.

OSD(On Screen Display) Menu

❖

OSD menu is provided to display the status of camera and to confi gure the functions interactively.

•

Coaxial Cable Communication

❖

This is a remote control function that overlaps the coaxial cable (for a transfer of the video signal) with the

•

control signal. In installation or repair, this helps you control the communication controller (optional) without
additional cabling.

PRODUCT & ACCESSORIES

❖

•

•

Came

6 – DIGITAL COLOR CAMERA

Introduction

Product & Accessories❖

Accessories

nd

a

t

•

Main Product

•

Camera Holder(Mount)

C Mount Adapter

Camera

User’s Manual

ENG

Auto Iris

Lens Connector

English – 7

Introduction

R

PART NAMES AND FUNCTIONS

Side View❖

Mount Adapter
Fixing Grooves

❖

Auto Iris Lens
Connector

Auto Iris Lens
Control Cable

Auto Iris Lens Connector

•

This groove is used for screwing the mount adapter, a part of the bracket where the camera will be installed.

Auto Iris Lens Control Cable

•

This cable transmits the power and signals from the camera for controlling the Auto Iris Lens.

Mount Adapter Fixing Grooves

•

These grooves are used when fi xing screws of the mount adapter connected to the bracket when installing
the camera on it.

Note :



When the camera lens becomes dirty, softly clean it with a lens tissue or a cloth soaked in pure ethanol.

–

8 – DIGITAL COLOR CAMERA

Camera Lens

Introduction

Rear Panel❖

<AC24/DC12V (SCC-B1331(P))>

lled.

ing

n

p

r

o

q

ENG

s

<AC220V~240V(SCC-B1031P)>

n

o

p

s

q

English – 9

Introduction

n

A

P
N

1

2

3

4

n Input/Output Connector

This connector has input and output ports for, DAY/NIGHT switching,
and alarm output signals.

No. Function Description

1 ALARM OUT

2 GND Grounding Port.

3 TRIGGER IN

4 SHUTTER (S0)

5 SHUTTER (S1)

6 SHUTTER (S2)

7 5V OUT

o SETUP Switch

This switch is used to set the function or property. When this switch is pressed for at least 2 seconds, the
MAIN MENU appears.

ef

(Left/Right)

: By pressing this switch left or right, you can move left or right on the menu or change the

cd

 : When you press this switch in the menu, the selected function is confi rmed. To enter a submenu, press

p Power Display LED

When the power is normally connected, the red LED lights.

q Video OUT Port

This is connected to the Video Input Port of the monitor and it outputs the Video signals.

r GND

This is a grounding port.

s Power Connection Port

This is connected to the Power cable.

displayed value.

(Up/Down) :

By pressing this switch up or down, you can move up or down on the menu.

this button.

Alarm out port for motion detection. (Open collector type)

Displays the current still image when it receives the Trigger signal.
(Normal Open Type)

This is a port for selecting an external high speed shutter mode.
If connected in LOW (0V), it will become ON inside.

This is a port for selecting an external high speed shutter mode.
If connected in LOW (0V), it will become ON inside.

This is a port for selecting an external high speed shutter mode.
If connected in LOW (0V), it will become ON inside.

Use within typical DC +5V 100mA

CO
CO

Con
the



No

–

10 – DIGITAL COLOR CAMERA

CONNECTING THE AUTO IRIS LENS
CONNECTOR

Installation

MOUNTING THE LENS

When using the CS lens

Mount the CS lens by rotating it clockwise as shown
in the picture:

CS lens

CS 렌즈

e

ess

the

Connect each uncovered shutter control cables to
the Auto Iris Lens Connector as the following

Pin

DC Control

No.

1 Damp(-) Power (+12V)

2 Damp(+) Not applicable

3 Drive(+) Video Signal

4 Drive(-) Ground

Note :



You can switch a control type of the lens in the menu.

–

Type

Video Control Type

When using the C lens

After mounting the C-mount adapter by rotating it
clockwise, turn the C lens clockwise until it is fi xed as
shown in the picture.

C 렌즈

C lens

English – 11

ENG

Installation

I



E
B

a



R



R



U
P
O



U
P
O

e

CONNECTING CABLES AND
CHECKING OPERATION

①

Connect one end of the BNC cable to the
VIDEO OUT Port on the rear of the camera.

② Connect another end of the BNC cable to the

VIDEO IN Port on the monitor.

Video In Terminal of Monitor Rear
Surface

BNC cable

1
.
A
L

A

R
2
.

A

G

M

N

O

D
3

U

.

T
T
R

5

I

.

G

S

4

G

.

H

S

E

U

H

R

6

T

U

.

T

I

S

T

E

N

T

H

R

E

U

(

S

R

7

T

1

(

.

T

5

S

)

E

O

V

R

)

(

O

S

8

U

2

.

)

T
D
A

Y
/
N

I

G

H

T
I
N

1

2

3

4

5

6
7

8

③

Finally connect the power adapter to the
camera. You can connect 2 lines of the power
adapter to the camera using the Slot Head
screwdriver as shown in the picture.
(GND: cable with the white stripe line)

1
.
A

L
A

R
2
.

A

G

M

N

O

D
3

U

.

T
T
R

5

I

.

G

S

4

G

.

H

S

E

U

H

R

6

T

U

.

T

I

S

T

E

N

T

H

R

E

U

(
S

R

7

T

1

(

.

T

S

)

5

E

O

V

R

)

(

O

S

8

U

2

.

)

T
D
A
Y

/

N

I

G
H

T

I
N

1 2

3 4

5 6 7

8

US

•

•

•

•

•

s

e

r

Video Out Terminal

12 – DIGITAL COLOR CAMERA

Note :



Connect any power source of AC 24V and DC 12V

–

irrespective of polarity.

How to use OSD Menu

USING ICONS IN THE MENU

 (EXIT)

•

Exits the menu setting.

er

Before you exits the menu setting, select SAVE to
save your settings, or select QUIT to cancel.

 (RET)

•

Returns to the previous menu.

 (HOME)

•

Returns to the main menu.

 (SAVE)

•

Used to save your settings of MASK AREA,
PRIVACY ZONE and more.
Once you save your settings, they will remain
even if you select QUIT in the menu.

 (DEL)

•

Used to deletes your settings of MASK AREA,
PRIVACY ZONE and more.
Once you delete your settings, they will not be
restored even if you select QUIT in the menu.

MAIN MENU

ÃÃMAIN MENUÃÃ

PROFILE



CAMERA SET

INTELLIGENCE
PRIVACY ZONE

OTHER SET

SYSTEM INFO

LANGUAGE



PROFILE

•

You can set a mode according to the camera
installation conditions.

CAMERA SET

•

Confi gure Camera related functions and data.

INTELLIGENCE

•

You can confi gure the settings of motion
detection, tracking and more.

PRIVACY ZONE

•

You can confi gure the privacy related settings.

OTHER SET

•

You can confi gure for Factory Defaults, and more.

SYSTEM INFO.

•

Displays the system information including the
camera version and communication settings.

•

LANGUAGE

Select a preferred one from the supported
languages.

ENG

English – 13

How to use OSD Menu

r
M

H

D

T

w

B

w

G

w

PROFILE

e

PROFILE

f

STANDARD

Ã

ITS
BACKLIGHT
DAY/NIGHT

GAMING
CUSTOM

 

In the PROFILE menu, you can confi gure the following camera settings at once.

P

W

CAMERA SET Menu

Previous

Menu

IRIS ALC ALC ALC ALC

ALC -- --

AGC VERY HIGH VERY HIGH- VERY HIGH VERY HIGH

DNR MID MID MID MID

SHUTTER OFF AUTO1/250 OFF OFF

XDR MID MID MID MID

STANDARD ITS BACKLIGHT GAMING

Sub-menus

LENS DC DC DC DC

LEVEL 0 0 0 0

BACKLIGHT OFF OFF - OFF

WEIGHT

WDR LEVEL

WHITE BAL

User setting

User setting

User setting

allowed

allowed

allowed

User setting

allowed

User setting

allowed

User setting

allowed

User setting

MID

0

allowed

14 – DIGITAL COLOR CAMERA

User setting

allowed

User setting

allowed

User setting

allowed

I

❖

It

❖

It

❖

It

How to use OSD Menu

CAMERA SET Menu

Previous

Menu

WHITE BAL DAY DAY/NIGHT DAY DAY

DAY -- --

DETAIL 2 2 2 2

ITS

❖

It will be set automatically so you can easily check the traffi c conditions.

BACKLIGHT

❖

It will be set automatically so you can distinguish the object from the background in a severe backlighting scene.

❖

GAMING

It will be set automatically to help you take a picture in a regular indoor lighting condition.

STANDARD ITS BACKLIGHT GAMING

Sub-menus

MODE ATW2 ATW1 ATW1 ATW1

RED00 00

BLUE 0 0 0 0

ENG

English – 15

How to use OSD Menu

②

L

①

CAMERA SETUP

eCAMERA SETf

CAMERA ID OFF
IRIS ALC
AGC VERY HIGH
DNR MID
SHUTTER OFF
SENS-UP AUTO X4
FLICKERLESS OFF
XDR MID

DIS OFF

 

WHITE BAL 
DIGITAL ZOOM
DETAIL [2]
V-SYNC INT
AGC COLOR SUP
REVERSE OFF
POSI/NEGA +
PIP OFF
 

Setup the general functions of zoom camera module.

cdef

Use the

16 – DIGITAL COLOR CAMERA

d

c

OFF

LOW

switch to select a menu item.

CAMERA ID [OFF, ON]

❖

CAMERA ID

ABCDEFGHIJKLMNOPQRSTUVWXYZ0
123456789 :?-+*()/

SP

ffee

SP LOCATION

CAMERA-1..................

...........................

  

The CAMERA ID menu is used for you to assign
a unique name to a camera. If you press the
SETUP switch with the CAMERA ID menu
selected, you will see the appropriate screen.

You can enter up to 54 alphanumeric or
special characters for the CAMERA ID. Select
LOCATION and press the SETUP switch to
move the display position of the CAMERA ID.

IRIS [ALC, ELC]

❖

The IRIS menu is used if you want to adjust the
intensity of radiation incoming to the camera.

ALC (Automatic Light Control)

•

① If you press the SETUP switch with an ALC-

based sub menu selected, you will see the
appropriate screen.

ALC

LENS DC
LEVEL [00]----I---­BACKLIGHT OFF

  

The LENS menu is used if you select a type of
the AI lens.

For normal operation, you must select DC for a
DC-type lens, and select VIDEO for a VIDEO­type lens.

–

E

•

.

e of

How to use OSD Menu

ELC

LEVEL [00]----I----

The LEVEL menu is used to adjust the
overall brightness, where “+” will increase the
brightness and “–” will decrease it.

② If you set the BACKLIGHT option to BLC,

you will see a menu where you can set the
BLC area.

you can set the desired BLC zone by defi ning
the size and location.

ign

t

e

C-

ALC

LENS DC
LEVEL [00]----I---­BACKLIGHT BLC
AREA USER
<SIZE>
<LOCATION>

  

If you use an ordinary camera in a scene
with an intensive backlight, the object will be
displayed dark on the monitor affected by the
backlight. To solve this problem, you can use
the BLC(Back Light Compensation) function
to improve the sharpness of the image in
such a high contrast scene.

–

ELC (Electronic Light Control)

•

①

If you press the SETUP switch when the ELC
submenu is selected, the corresponding screen
appears. You can make the ELC (Electronic Light
Control) function active or not.

r a

-

BACKLIGHT OFF

  

② In similar to ALC setting, you can specify the

BLC area.

ELC

LEVEL [00]----I---­BACKLIGHT BLC
AREA USER
<SIZE>
<LOCATION>

  

AGC

❖

[OFF, VERY LOW, LOW, MID, HIGH, VERY
HIGH, USER]

The AGC (Auto Gain Control) menu is used to
set the AGC level of the camera. When the AGC
is active, the camera automatically increases the
sensitivity by amplifying the Video signal when
the strength of the signal falls below the normal
value.

If you press the SETUP switch with a USER
sub menu selected, you will see the appropriate
screen.

ENG

English – 17

How to use OSD Menu

A
d
e
b

F

f

d

r

X

O

A
w

n

v

S
C

e

W

f

W

A

n

R

c

SHUTTER

AGC USER

LEVEL [16]

  

In USER mode, you can break down the level in
16 steps from VERY LOW to VERY HIGH to your
preference.

AGC FIX

LEVEL [01]

  

If you press the SETUP switch with a FIX sub
menu selected, you will see the appropriate screen.

As a fi xed value of the AGC gain is used in FIX
mode, you can select one of the 16 detailed levels
from VERY LOW to VERY HIGH before fi xing it.

.

❖

DNR

[OFF,LOW,MID,HIGH, USER(1~16)]

You can confi gure the DNR (Digital Noise
Reduction) related settings.

Reduces the noise on the screen.
This is especially useful for a severely distorted
screen.

You can set the level if you set DNR to USER.

❖

[OFF, AUTO 1/100(PAL:1/120), AUTO 1/250,
AUTO 1/500, AUTO 1/1000, AUTO 1/2000, AUTO
1/4000, AUTO 1/10K , 1/100(PAL:1/120), 1/250,
1/500, 1/1000, 1/2000, 1/4000, 1/10K , EXT]

The SHUTTER menu is used to set the fi xed
high-speed electronic shutter, auto high speed
electronic shutter and external high speed
electronic shutter(EXT).

You can select one of 7 options from 1/100(PAL:1/120)
to 1/10K for the fi xed high speed electronic shutter,
which is mostly used for imaging a fast moving object.

The auto high speed electronic shutter operates
as the fi xed high speed shutter in a high contrast
scene but automatically focuses the target if the
iris opens fully in a low contrast scene like in ELC
mode. When it gets brighter back, the mode will
switch to the fi xed high speed electronic shutter
mode.

However, the auto high speed shutter operates
properly only in a camera featuring a DC or VIDEO
lens.

In external high speed electronic shutter (EXT)
mode, you can select one of 8 modes from OFF
through 1/100(PAL:1/120) to 1/10K for the high
speed electronic shutter. It works as the high
speed electronic shutter. You can select an
option using SHUTTER(S0), SHUTTER(S1) and
SHUTTER(S2) on the rear.

Connect each of the terminals to GND.

See the below table for the operation.

SHUTTER(S0) SHUTTER(S1) SHUTTER(S2)

OFF

(NTSC: 1/60,

OFF OFF OFF

PAL:1/50)

1/100

(PAL:1/120)

ON OFF OFF

1/250 OFF ON OFF

1/500 ON ON OFF

1/1000 OFF OFF ON

No



–

–

–

❖

I
1

f

❖

[

i

l

❖

I

D

•

I

18 – DIGITAL COLOR CAMERA

TO

,

s
st
e

ill

h

,

120)

ct.

C

r

EO

F

(S2)

How to use OSD Menu

1/2000 ON OFF ON

1/4000 OFF ON ON

1/10K ON ON ON

Note :



If IRIS mode is set to ELC, the SHUTTER menu will be

–

deactivated as you adjust the brightness using the
electronic shutter.

If the SENS-UP function is set to AUTO, only items of

–

OFF and AUTO are available in the SHUTTER menu.

–

If the FLICKERLESS function is set to ON, the SHUTTER menu
will be deactivated.

Automatically detects the ambient level of
darkness in the dark or low contrast scene to
extend the accumulated time, keeping the image
bright and sharp;

❖

FLICKERLESS [OFF, ON]

If set to ON, the shutter speed will be fi xed to
1/100(PAL:1/120) second. This will prevent possible screen
distortion due to a mismatch between the vertical sync
frequency and the blinking frequency of the lighting.

❖

XDR (eXtended Dynamic Range)
[OFF, LOW, MID, HIGH]

Actively controls the gamma compensation in the
way it operates the ambient luminance contrast
in a certain pixel unit to determine the optimal
visibility.

Select one from OFF, LOW, MID and HIGH.
Closing to HIGH will increase the compensation
level.

❖

WHITE BAL [DAY/NIGHT]

If you want to adjust the color scheme, use the
WHITE BALANCE function.

•

DAY

In DAY mode, you can set the color values of
RED and BLUE. The screen will be displayed in

colors according to your settings.

WHITE BAL

DAY/NIGHT DAY
MODE AWC
RED [00]----I---­ BLUE [00]----I---­ R-GAIN [0248]
B-GAIN [0247]

  

Note :



You can set the values of R-GAIN and B-GAIN only in

–

AWC mode.

If AGC is set to OFF or FIX, you can not access the

–

NIGHT menu.

–

For adjusting the white balance, the following
5 modes are provided:

•

ATW1(Auto Tracing White Balance mode

1): The camera can automatically adjust the
color temperature in real time, according to
the ambient conditions. The color temperature
ranges from approx. 2500K to 9300K.

•

ATW2: The color temperature ranges from
approx. 2,000K to 10,000K.

•

AWC ( Auto White Balance Control): If you
press the SETUP switch in the appropriate item
position, Auto White Balance will perform once.

•

3200K : Set color temperature to 3200K

•

5600K : Set color temperature to 5600K

–

RED : Adjusts the strength of the red color.

–

BLUE : Adjusts the strength of the blue color.

–

R-GAIN/B-GAIN : Enables you to set the current
color temperature manually.

–

BRIGHTNESS : Select a brightness level in
switching from setting in DAY mode to setting in
NIGHT mode.

–

ENG

English – 19

How to use OSD Menu

T

E

M

R

e

E

e

M

S

S
p

D

W

u

d

S

DIGITAL ZOOM [ON/OFF]

❖

You can set the digital zoom factor and position.
If you press the SETUP switch with the DIGITAL
ZOOM function set to ON, you will see the
appropriate screen.

When the zoom factor and position are defi ned,
the digital zoom function will operate.

DIGITAL ZOOM

RATIO [X1.0]
< LOCATION >



  

-

LOCATION : If you press the SETUP switch in the
condition where the image is enlarged as much as the
ratio setting, you can watch an invisible area of the
effective screen as well using the



Note :

The DIGITAL ZOOM function enlarges the pixel itself, which can

–

cause deterioration of the quality.

DETAIL [0~3]

❖

Controls the horizontal or vertical distinction.

V-SYNC [INT, LINE]

❖

Select the vertical sync mode for INT or LINE.

If you select INT, the camera will use the internal
synchronization.

If selecting LINE, the camera will use the external
power source frequency for the synchronization.

You can adjust the LL-PHASE.



Note :

Use of DC 12V will fi x V-SYNC to INT, which can not be

–

changed.

❖

AGC COLOR SUP [LOW , MID, HIGH]

Adjust the color scheme according to the AGC
value.

cdef

switch.

20 – DIGITAL COLOR CAMERA

REVERSE [OFF, H, V, H/V]

❖

Mirrors video signals horizontally, vertically, or
both.

POSI/NEGA [+, -]

❖

Output as it is or mirror the video brightness
signal.

PIP [OFF, ON]

❖

Displays a sub image together with the main
image on the same screen using the Picture In
Picture function.



Note :

If more than one privacy zone is set and the PRIVACY

–

SET is set to ON, the PIP function will be deactivated.

–

If the INTELLIGENCE function is set to FENCE mode, the
PIP menu will be deactivated.

DIS [OFF, ON]

❖

Digital Image Stabilization will set the anti-shake
compensation.

Note :



If you set DIS to ON, the compensation area will be

–

enlarged as set in the digital zoom factor.
If you set the digital zoom factor to greater than the
enlarged zoom factor for the compensation, the DIS
function will be deactivated.

IN

You

INT

❖

•

•

❖

❖

❖

T

D

D

D

f

How to use OSD Menu

Y

.

he

INTELLIGENCE

eINTELLIGENCEf

MOTION OFF
MASK AREA
DISPLAY ON
SENSITIVITY [4]
RESOLUTION [5]
ALARM OUT 

 

You can set the motion detection and tracking in the

INTELLIGENCE menu.

MOTION

❖

•

TRACKING

Detects and tracks a moving object.

•

DETECTION

Detects a moving object.

❖

MASK AREA [1~4]

Specify a detection exception area to mask.

Select a mask number and specify the size and
position.

<SIZE> 
<LOCATION>

    

DISPLAY [ON, OFF]

❖

With the DISPLAY option set to ON, a motion
function will be displayed on the screen, if
detected.

SENSITIVITY [1~7]

❖

1 2 3 4

[OFF,TRACKING,DETECTION]



MASK AREA



Set the sensitivity of the motion detection.

RESOLUTION [1~5]

❖

If setting it to high, the camera can detect even a
trivial movement of the target.

ALARM OUT

❖

If you set a desired menu item to ON, the camera
will sound an alert if it detect the appropriate
motion.

ALARM OUT

MOTION ON

  

English – 21

ENG

How to use OSD Menu

H

F

A
d

O

Y
C

PRIVACY ZONE SETUP

ePRIVACY ZONEf

1 2 3 4 5 6
7 8 9

PRIVACY SET ON
STYLE

 

The PRIVACY function will protect your privacy by
screening the privacy area that you have specifi ed
during monitoring. You can specify up to 12 privacy
zones.

If you set the PRIVACY SET to ON, your PRIVACY
ZONE settings will be applied.

You can change the style to adjust the mosaic size
and color of the PRIVACY ZONE.

ePRIVACY ZONEf

1 2 3 4 5 6
7 8 9

PRIVACY SET ON
STYLE COLOR
Y-LEVEL [128]
RED [128]
BLUE [128]



cdef

Use the
PRIVACY 1 through 12.

Select one from PRIVACY 1~12 and press the
SETUP switch to confi rm your setting. You can
specify a pixel that moves as you change the PIXEL
LEVEL to set the position.

10 11 12

MOSAIC1

10 11 12



switch to select one from

PRIVACY ZONE SET1

PIXEL LEVEL [4]
<POINT>
<POSITION>

    

- How to set the point

You can set each position of the 4 points.

① If you press the SETUP switch in <POINT>,

you will see the points available in the

PRIVACY ZONE. Each time you press the
SETUP switch, the points available will move.

② Use the

cdef

cdef

switch to set the position

switch to move the

of each point. Set each position of the four
points and press the SETUP switch to
complete the positioning.

- How to set the position

You can move the position of the overall area.

① By pressing the SETUP switch in

<POSITION>, you can move the overall

position of the privacy zone.

② Use the

position and press the SETUP switch to
confi rm it.

Note :



If more than one PRIVACY ZONE is specifi ed and the

–

PRIVACY SET is set to ON, the PIP function will be
deactivated.

If the 12th PRIVACY ZONE is specifi ed, the LINE function

–

of FENCE will be deactivated.

OT

❖

❖

22 – DIGITAL COLOR CAMERA

How to use OSD Menu

t

OTHER SET

eOTHER SETf

FACTORY DEFAULTS
OSD COLOR BW

 

>,

ve.

ion

r

.

tion

FACTORY DEFAULTS

❖

All the settings will be restored to the factory
default.

OSD COLOR [BW, R/G/B]

❖

You can set the OSD(On-screen Display) color to
COLOR or B/W.



SYSTEM INFORMATION

eSYSTEM INFOf

TYPE 3_BOX_WDR_N
SERIAL NO.

000000000000000

CAMERA VER. 0.50_090101

 

You can view the system information including,
camera version

LANGUAGE

eLANGUAGEf

ÃENGLISH

FRANÇAIS

ESPAÑOL

日文

INGLÊS

 

The camera supports 5 different languages.

Select a preferred language.

ENG

English – 23

How to use OSD Menu

S

E

Initial Confi guration Table

❖

Camera Confi guration

•

CAMERA ID OFF

IRIS ALC

AGC VERY HIGH

DNR MID

SHUTTER OFF

FLICKERLESS OFF

XDR MID

DIGITAL ZOOM OFF

DETAIL [2]

AGC COLOR SUP MID

REVERSE OFF

POSI/NEGA +

PIP OFF

DIS OFF

SP

24 – DIGITAL COLOR CAMERA

Specifi cations

SPECIFICATIONS

Items Sub-items SCC-B1331N

Camera Type

Image

Scanning

Min. Scene

Illumination

Functions

Resolution

Video Output

S/N Ratio

Pixels

System Interlace/Progressive

Scanning Line 525 lines

Frame 30frame/1sec

Horizontal
Frequency

Vertical

Frequency

Number of Privacy Zone 12 (Polygonal Method)

Motion Detection OFF/Tracking/Detection

eXtended Dynamic Range(XDR) Off/On (Level Setting)

D-Zoom x1 ~ x16 (x0.1 STEP)

High Speed Shutter 1/60 ~ 1/10Ksec (OSD/External Control)

Flickerless Off/On

Sens-Up x2 ~ x512

Line Lock Off/On (Phase Control)

Camera ID Off/On (Max.54ea/2Line)

White Balance ATW1/ATW2/AWC/3200K/5600K

Digital Noise Reduction(DNR) Off/On (Adaptive 3D+2D)

Digital Image Stabilization(DIS)

Intelligent Video Fixed/Moved, Fence

Etc. Function Detail, Reverse(H/V), Posi/Nega

Horizontal 600 TV Lines

S/N Ratio Approx. 52dB

CCTV Camera (WDR & DAY/NIGHT)

Device 1/3” Super-HAD IT CCD

Total 811 x 508

Effective 768 x 494

Internal Mode 15,734 Hz

Line-lock Mode 15,750 Hz

Internal Mode 59.94 Hz

Line-lock Mode 60 Hz

Condition Min. Scene illumination

Sens-up F No. Level DAY NIGHT

OFF 1.2 50 IRE 0.4 Lux 0.4 Lux
OFF 1.2 30 IRE 0.24 Lux 0.24 Lux

OFF 1.2 15 IRE 0.12 Lux 0.12 Lux

PIP Off/On

BLC Off/On (Area Setting)

AGC Off/On (Max.Level Setting)

ELC Off/On ( ~ 1/200K sec)

Vertical 350 TV Lines

- VBS 1.0Vp-p, 75 Ω

ENG

Off/On

English – 25

Specifi cations

Items Sub-items SCC-B1331N

Lens

Alarm

Remote

Control

Environmental

Conditions

Power

Physical

Specifi cation

Lens Drive Type MANUAL/AI(VIDEO/DC)

Mount Type CS/C

Input N/A

Output 1 Output

Coaxitron (Data On Coax cable) Yes (with SCX-RD100)

Operating Temperature -10˚C ~ +50˚C

Humidity Less than 90%

Power Requirement

Power Consumption

(With DC Lens)

LED Indicator Yes

Dimensions

(WxHxD)

Weight

Color Body Silver

Net 64(W) x 58(H) x 109.2(D) mm

Package 173(W) x 99(H) x 115(D) mm

Net 305g

Package 530g

AC24V ± 10%(60Hz ± 0.3Hz)

DC12V ± 10%

In normal operation : 2.6W

In switching the DAY/NIGHT fi lter : 3.2W

26 – DIGITAL COLOR CAMERA

Specifi cations

Items Sub-items SCC-B1331P / SCC-B1031P

Camera Type

Image

Scanning

Min. Scene
Illumination

Functions

Device 1/3” Super-HAD IT CCD

Pixels

System Interlace/Progressive

Scanning Line 625 lines

Frame 25frame/1sec

Horizontal

Frequency

Vertical

Frequency

Number of Privacy Zone 12 (Polygonal Method)

Motion Detection OFF/Tracking/Detection

eXtended Dynamic Range(XDR) Off/On (Level Setting)

D-Zoom Max. x16

High Speed Shutter 1/50 ~ 1/10Ksec (OSD/External Control)

Flickerless Off/On

Sens-Up x2 ~ x512

Line Lock Off/On (Phase Control)

Camera ID Off/On (Max.54ea/2Line)

White Balance ATW1/ATW2/AWC/3200K/5600K

Digital Noise Reduction(DNR) Off/On (Adaptive 3D+2D)

Digital Image Stabilization(DIS)

Intelligent Video Fixed/Moved, Fence

Etc. Function Detail, Reverse(H/V), Posi/Nega

CCTV Camera (WDR & DAY/NIGHT)

Total 795 x 596

Effective 752 x 582

Internal Mode 15,625 Hz

Line-lock Mode 15,625 Hz

Internal Mode 50 Hz

Line-lock Mode 50 Hz

Condition Min. Scene illumination

Sens-up F No. Level DAY NIGHT

OFF 1.2 50 IRE 0.4 Lux 0.4 Lux
OFF 1.2 30 IRE 0.24 Lux 0.24 Lux

OFF 1.2 15 IRE 0.12 Lux 0.12 Lux

PIP Off/On

BLC Off/On (Area Setting)

AGC Off/On (Max.Level Setting)

ELC Off/On ( ~ 1/200K sec)

Off/On

ENG

English – 27

Items Sub-items SCC-B1331P / SCC-B1031P

Image

Device 1/3” Super-HAD IT CCD

Horizontal 600 TV Lines

Resolution

Video Output

S/N Ratio

Lens

Alarm

Remote
Control

Environmental

Conditions

Vertical 350 TV Lines

- VBS 1.0Vp-p, 75 Ω

S/N Ratio Approx. 52dB

Lens Drive Type MANUAL/AI(VIDEO/DC)

Mount Type CS/C

Input N/A

Output 1 Output

Coaxitron (Data On Coax cable) Yes (with SCX-RD100)

RS-485 Yes (Multi Protocol, 8ea)

Operating Temperature -10˚C ~ +50˚C

Humidity Less than 90%