Samsung S832GWS Service manual

WASHING MACHINE

S832GWS/YLP

Manual

ERVICE

WASHING MACHINE

Caution for the safety during servicing

1. SPECIFICATIONS

2. SAFETY DEVICES

3. OVERVIEW OF THE WASHING MACHINE

4. OVERVIEW OF THE CONTROL PANEL

5. MAIN FUNCTION

6. TECHNICAL POINT

7. GENERAL ERROR FUNCTION

8. TROUBLE DIAGNOSIS

9. TEST MODE

10. DESIGNATION OF MAIN COMPONENTS

CONTENTS

11. PCB SCHEMATIC DIAGRAM

11-1. PCB CIRCUIT DIAGRAM

12. SETTING UP A WASH MACHINE

13. ASSEMBLE AND DISASSEMBLE

. TOOLS FOR DISASSEMBLY AND ASSEMBLY

15. EXPLODED VIEW AND PARTS LIST

Cautionforthesafetyduringservicing

1. Do not allow the customer to repair the product.

☞

The person may be injured or the product life may be shortened.

2. Execute A/S after unplugging the power supply unit.

☞

Be care of the electric shock.

3. Do not plug several plugs in the same outlet.

☞

It may cause the fire due to overheat.

4. Check the damage, pressing or burning of the power plug or outlet.

☞

Replace it promptly if it has problem.((may cause the electric shock or fire)

5. Do not clean the main body with the water.

☞

It may cause the electric shock and fire and shorten the product life))

6. The wiring of the harness shall be free from the moisture and tightened during serving.

☞

It shall not be deviated by certain impact.

7. Remove any dust or filth on the housing section,wiring section,connection section during servicing.

☞

Protect the cause of the fire such as the tracking,and etc.

8. Check any mark of the moisture on the electrical parts, harness section and etc.

☞

Replace the parts or remove the moisture.

9. Check the assembly status of the parts after servicing.

☞

Maintain the status before servicing.

10. Pull out the power cord with holding the plug.

☞

Be care of the electric shock and fire when the cord is damaged.

11. Unplug the power plug from the outlet when the wash machine is not used.

☞

Be care of the electric shock and fire due to the strike of the lightening.

12. Do not use or store the spray or flammable materials(including gasoline,alcohol and e tc.)

around the wash machine.

☞

Be care of the explosion or fire due to the electric spark.

13. Do not put the bowl of water or wet laundry on the wash machine.

☞

If the water is penetrated to the wash machine, this may cause the electric shock or fire.

14. Do not install the wash machine in the place where the snow or rain falls.

☞

It may cause the electric shock and fire and shorten the product life.

15. Do not push the control buttons with the awl,pin, or sharp materials.

☞

It may the electric shock and trouble.

16. Check the wash machine is leveled horizontally and installed properly on the floor.

☞

The vibration may shorten the product life.

17. Joint the wire by the connector correctly.

☞

When the wire is jointed by the tape, this may cause the fire due to the tracking.

18. When the wash machine is to be laid for the service, put the pad on the floor and lay the product at

side slowly.

☞

If the wash machine is laid front, the relay may be damaged by the tub.

19. When the wash-heater is replaced, check it is inserted in the bracket-heater and screw the nut.

☞

If the wash--is not inserted in the bracket-heater properly, this may cause the noise and

leakage since it is contacted to the drum.

- 1 -

1. Specifications

WASH TYPE

DIMENSION

WATER PRESSURE

WEIGHT

WASH and SPIN CAPA CITY

POWER CONSUMPTION

WATER CONSUMPTION

SPIN REVOLUTION

FRONT LOADING TYPE

GROSS W 665mm X D 470mm X H 890mm

NET W 598mm X D 340mm X H 844mm

50 kPa ~ 800 kPa

GROSS 58 kg

NET 55 kg

3.5 kg (DRY LAUNDRY)

220 V 110 W

WASHING

WASHING and HEATING

MODEL S832

SPIN

220-240V

PUMPING 34 W

MODEL S832

rpm 800

240 V 110 W

220 V 900 W

240 V 1050 W

170 W

43ℓ(STANDARD COURSE)

- 2 -

2. Safety Devices

※

We adapt 5 safety devices for users to use this wash machine safely.

1) Balancing device (ASSY-Main PCB)

→

When the laundry is out of balance, to prevent the noises and vibrations, the unbalance

detecting sensor helps the laundry laid even and continue the dehydating process.

2) Anti-over water supply device

→

Because water supply value is broken, once water is supplied to the 2/3 level of the door, the

water supplied is drained automatically, Over -flow error is displayed on the panel

3) Temperature-regulating device(thermistor)

→

To prevent over-heating over the temperature setted up, THERMISTOR senses the temperature of

the machine continuously and helps the wash machine to work at the temperature given by users.

4 Overheating- controlling system

→

Under the circumstances of THERMISTOR inferiority or abnormal condition, if wash-heater is

overheated, automatically, assy -thermal fuse cuts off the power supply to protect the machine to

keep it safe.

5) Delicate clothing safeguard function(ASSY-Main PCB)

→

To protect the clothings which is weak to high temperature, the wash machine senses the

temperature inside the washing tub. if the temperature rises over 50℃wool washing course and

Delicate washing course display abnormal water temperature on the panel , after draining the

water.

- 3 -

3. Overview of the Washing Machine

- 4 -

4. Overview of the control panel

S832

2 3 4 5 6

1. Detergent dispenser

2. Display panel

Displays wash cycle and error messages by LED lamps.

3. Course button

Press the button repeatedly to select one of the six availabel wash program.

{Cotton.Synthetics.Delicates .Quick.Rinse+Spin.Spin.Cotton }.

Temperature selection button

Press the button repeatedly to cycle through the available water temperature options

(cold, 40 ° C , 60 °C and Bio 60 °C).

Bio 60°C : To improve the Wash efficiency, heating during 30 min.

5. Spin selection button

Press the button repeatedly to cycle through the available spin speed options.

S832

6. Start/Pause button

Press to pause and restart programs.

7. 1(

On/Off) button

Press once to turn the washing machine on, press again to turn the washing machine off.

If the washing machine power is left on for longer than 10 minutes without any buttons

being touched, the power automatically turns off.

no spin, 600, 800 rpm

- 5 -

5. Main function

1) Auto power S/W off function

●

After power on, the auto power S/W off function automatically switches power off for you if you do not press

selection button for 10 minutes

●

After selecting the function, the auto power S/W off function automatically switches power off for you if you do

not press start/pause button for 10 minutes

●

After finishing the last function, the auto power S/W off function automatically switches

power off for you if you do not re-select the course button or manual button

2) Door open function

●

If door is open during the operating, all operating is halted, and door error message will be displayed.

●

Door open error can be cleared by colosing the door. the operating keeps going on

3) No spin function

●

If no spin function selected, the operating is finished after last rinse

- 6 -

5. Main function

4) Power-out compensation function

●

If power is out on selected process, the process before power out is stored to EEPROM, once power is back

the process before power out continues.

●

When power is back, washing process starts from the process at the point of the power out, rinse/drain process

starts from the initial process.

POWER-OUT COMPENSATION FUNCTION PROCESS

WASHINGSTART

POWER OUT

SAVE DATA

to EEPROM

READ DATA

(PROCESS+TIME)

5) Water heater Error function

①

This function starts working, when the heater works abnormally.

(this function begins sensing the heater 1 minutes later, after the heater operating)

②

The value of the initial thermistor(A1) is compared with that of the thermistor(A2) in 2 minutes (Y=A2-A1)

- For 10 minutes, the variance of temperature(Y) is less than 2

message is displayed on the panel.

③

The value of the initial thermistor(A1) is compared with that of the thermistor(A2) in 2 minutes (Y=A2-A1)

- For 2 minute the variance of temperature increases more than 4.5

led on" message is displayed on the panel.

④

At this time heater, Error "course led 6ea on cold/60℃led on" is displayed and all working process off

⑤

The heater operating continues during heating hours, if washing hour is left over, the residual washing process

keeps going without heating.

POWER BACK

MICOM RESTORE

RESTART

PROCESS

RINSE/DRAIN

START

SAVE DATA

to EEPROM

℃

"courseled6eaon40℃/60℃led on"

℃

(0.2148V) "course led 6ea on cold/60

RINSE/DRAIN

PROCESS

POWER OUT

POWER BACK

MICOM RESTORE

FINISH

℃

- 7 -

5. Main function

6) Fuzzy washing function ( weight-sensing)

☞

After finishing initial water supply, when the fall of the water level needs supplementary water supply,

Sensing function perceives the weght with the supplementary water supply numbers and starts to work.

Under the course of Cotton, if the supplementary water supply numbers become 3 - 4 times the

function is going at default condition ( high water level ), if 1-2 below that is going at middle level, if 0 below

low water level, heating hours and rinse hours depend on the above data.

Washing hours

Rinse water level

Cotton

High Default Default

Middle Default-12 min 22.80KHZ

Low Default-25 min 23.30KHZ

※

After sensing weight, above hours is decreased from above default hours

7) Bubble -detecting function

At the each condition of washing&dehydrating , rinse&dehydrating , hydrating, bubble -detecting function works,

this function works 5times normally, if the function detects bubbles at 6 times , the bubble-detecting function

stops and go on to the next process.

●

The bubble-detecting function during washing & dehydrating to rinse & dehydrating

after 2 times instant dehydrating and before main dehydrating, if the water level is under 25.45KHZ, Bubble

→

Detecting function thinks there are bubbles and add the bubbles-removing rinse, needing hours are above

hours and 6 min 40 sec.

→

The bubble-detecting function during single hydrating process

after 2 times instant dehydrating and before main dehydrating , if the water level is 25.45KHZ below or

during main dehydrating, water level data is 23.80KHZ below Bubble-detecting function thinks there are

bubbles and add the bubbles-removing rinse 1 times, needing hours are above hours and 5 min 50 sec.

Bubble-detecting function operating process

20 sec

laundry scattering

draining &reverse

1min20sec

unbalance

detecting range

- 8 -

210rpm

5sec20sec 15sec 5sec

bubble detection

(default water level 25.45KHZ below)

210rpm

15sec

5. Main function

8) Unbalance detecting & laundry balance positioning system

①

Just before the hydrating process and just after reversal rotation for balancing laundry position, this function is

carried out

②

The initial 6 sec is the period of reversal rotation for balancing laundry position , Drum rotates 50rpm for

initial 6 sec

③

Next 10 sec, the rotation increases the speed from 50 rpm to 90 rpm slowly

④

During the next 18 sec, drum rotates at the speed of 90 rpm, the sensor decides the degree of laundry

unbalance with TACHO data which is attached to motor

⑤

If the degree of unbalanced laundry is over 6 times to default value, laundry balancing system carryies out

feed back process 6 times

- 9 -

6. Technical point

1) Motor on/off time at each course

Washing Rinse

Course

Cw Off Ccw Off Cw Off Ccw Off

Cotton

Synthetics

Delicates

Quick

13 3 13 3 10 5 10 5 50

7 8 7 8 7 8 7 8 40

5 10 5 10 5 10 5 10 30

12 3 12 3 10 5 10 5 45

2) Final dehydrating r.p.m at each course

Model

Course

Cotton

Synthetics

unit:sec

Motor r.p.m

unit:rpm

S832

800

Delicates

Quick

※

You can change the r.p.m to the above a table by use spin button under no spin situation.

600

800

- 10 -

6. Technical point

3) The water level data at each course

Course

Cotton

Synthetics

Delicates

Quick

Water level

Washing

Rinse

Washing

Rinse

Washing

Rinse

Washing

Rinse

Default water level(khz)

23.50 24.00 23.70

large 22.45

small 23.30

23.50 24.00 23.70

22.45 24.00 23.50

22.80 23.55 23.35

22.65 23.55 23.35

23.50 24.00 23.70

22.45 24.00 23.50

4) The other water level data

The water data unter each conditon

Supplemetary water

START(Khz)

24.00 23.50middle 22.80

unit:Khz

Supplemetary water

end(khz)

1st water supply (only preparation)

Overflow error

Bubble

detectingatwashing/rinse/dehydrating

Bubble detecting rinse water level

Water level which can open door

Water level which can drive heater

Water level which can reset the drain

※

If water level is 15KHZ below or 30 KHZ above , sensor-pressur is out of order so needs changing.

24.60(1.8ℓ) 1st water supply level to washing tub

20.50 The water supplied reach 2/3 of door

25.45 Bubble -detecting water level

22.00 The water level which can detect bubbles

over

23.80

24.50(2ℓ) Safety water level of wash heater

24.50 The water level can be detected after 1st draining

It is possible to open the door

unit:Khz

- 11 -

7. General Error Function

When an error occurs, this function starts to keep generating error melody sounds and displays error indicators as shown in the followings per corresponding error by blinking in 0.5sec interval until the error status is completely cleared out. In this case, all the driving devices are turned off until the error is cleared out.

1. WATER SUPPLY ERROR

- Display shows such as fig. 1

- Water Supply Error occurs when water level frequency does not show changes more than 100Hz or water is not supplied up to the water level presetting for 20 min or more at the time of initial water supply.

-The error status can be cleared by turning POWER S/W OFF and resuming the POWER ON initial status.

2. WATER DRAIN ERROR

- Display shows such as fig.2

- In case the water level frequency is 24.5KHz or less in the initial phase of UNB-detecting cycle.

- Water Drain error can be cleared by turning POWER S/W OFF and resuming the POWER ON initial status.

3. OVER-FLOW ERROR

- Display shows such as fig.3

- Over-Flow error occurs when the water level is in abnormal operation. ItcanbeclearedbyturningPOWERS/WOFF. Water is drained prior to POWER S/W OFF and it is forced to be drained for 2 min if a frequency of more than 24.5 KHz is detected.

fig. 1

fig. 2

fig. 3

○:Lighton

●:Lightoff

4. UNBALANCE ERROR

- Display shows such as fig4.

- Laundry load is unbalanced; loosen any tangled laundry.

- If only one item of clothing needs washing, such as a bathrobe or jeans, the final spin result might be unsatisfactory and an error message will be shown in the display panel such as fig 4..

- Unbalance error is cleared by POWER S/W OFF and by resuming the POWER ON initial status.

5.WATERHEATERERROR

- Display shows such as fig.5 or fig.6

- In case the water temperature rises by 7° C or more in 1 min. or by 2°C less in 10 min after heating is started.

- It can be cleared by turning POWER S/W OFF.

6 DOOR OPEN ERROR

- Display shows such as fig.7

- Door Open error can be cleared by closing the door.

fig. 4

fig. 5

fig. 6

7. ASS’ Y PRESSURE S/W ERROR

* Generated Frequency Signal of WATER LEVEL(W/L) S/W (KHz)

Level Low Level High Level

Abnormal W/L Frequency 30.00 KHz 15.00 KHz

- 12 -

fig. 7

+ 30 hidden pages