Samsung S803J, S803JGW3 Service Manual

Caution for the safety during servicing

1. Do not allow the customer to repair the product.

☞

The person may be injured or the product life may be shortened.

2. Execute A/S after unplugging the power supply unit.

☞

Be care of the electric shock.

3. Do not plug several plugs in the same outlet.

☞

It may cause the fire due to overheat.

4. Check the damage, pressing or burning of the power plug or outlet.

☞

Replace it promptly if it has problem. (may cause the electric shock or fire)

5. Do not clean the main body with the water.

☞

It may cause the electric shock and fire and shorten the product life.

6. The wiring of the harness shall be free from the moisture and tightened during serving.

☞

It shall not be deviated by certain impact.

7. Remove any dust or filth on the housing section,wiring section,connection section during servicing.

☞

Protect the cause of the fire such as the tracking,and etc.

8. Check any mark of the moisture on the electrical parts, harness section and etc.

☞

Replace the parts or remove the moisture.

9. Check the assembly status of the parts after servicing.

☞

Maintain the status before servicing.

10. Pull out the power cord with holding the plug.

☞

Be care of the electric shock and fire when the cord is damaged.

11. Unplug the power plug from the outlet when the wash machine is not used.

☞

Be care of the electric shock and fire due to the strike of the lightening.

12. Do not use or store the spray or flammable materials(including gasoline,alcohol and etc.) around the wash machine.

☞

Be care of the explosion or fire due to the electric spark.

13. Do not put the bowl of water or wet laundry on the wash machine.

☞

If the water is penetrated to the wash machine, this may cause the electric shock or fire.

14. Do not install the wash machine in the place where the snow or rain falls.

☞

It may cause the electric shock and fire and shorten the product life.

15. Do not push the control buttons with the awl,pin, or s harp materials.

☞

It may the electric shock and trouble.

16. Check the wash machine is leveled horizontally and installed properly on the floor.

☞

The vibration may shorten the product life.

17. Joint the wire by the connector correctly.

☞

When the wire is jointed by the tape, this may cause the fire due to the tracking.

18. W hen the wash machine is to be laid for the service, put the pad on the floor and lay the product at

side slowly.

☞

If the wash machine is laid front, the relay may be damaged by the tub.

19. When the wash-heater is replaced, check it is inserted in the bracket-heater and screw the nut.

☞

If the wash is not inserted in the bracket-heater properly, this may cause the noise and

leakage since it is contacted to the drum.

1. Specifications

WASH TYPE DIMENSION

WATER PRESSURE WEIGHT

WASH and SPIN CAPA CITY POWER CONSUMPTION

WATER CONSUMPTION

SPIN REVOLUTION

FRONT LOADING TYPE

GROSS W 680mm X D 470mm X H 892mm

NET W 598mm X D 340mm X H 844mm

50 kPa ~ 800 kPa

GROSS 58 kg

NET 55 kg

3.5 kg (DRY LAUNDRY)

220 V 70 W

WASHING

WASHING and HEATING

MODEL S803J

SPIN

220-240V

PUMPING 34 W

MODEL S803J

rpm 800

240 V 70 W

220 V 1800

240 V 2100

200 W

43ℓ(STANDARD COURSE)

2. Safety Devices

※

We adapt 5 safety devices for users to use this wash machine safely.

1) Balancing device (ASSY-Main PCB)

→

When the lauandry is out of balance, to prevent the noises and vibrations, the unbalance

detecting sensor helps the laundry laid even and continue the dehydating process.

2) Anti-over water supply device

→

Because water supply value is broken, once water is supplied to the 2/3 level of the door, the

water supplied is drained automatically, Over -flow error (E3) is displayed on the panel

3) Temperature-regulating device(thermistor)

→

To prevent over-heating over the temperature set up, THERMISTOR senses the temperature of

the machine continuously and helps the wash machine to work at the temperature given by users.

4 Overheating- controlling system

→

Under the circumstances of THERMISTOR inferiority or abnormal condition, if wash-heater is

overheated, automatically, assy -thermal fuse cuts off the power supply to protect the machine to

keep it safe.

5) Delicate clothing safeguard function(ASSY-Main PCB)

→

To protect the clothings which is weak to high temperature, the wash machine senses the

temperature inside the washing tub. if the temperature rises over 50℃wool washing coure and

Delicate washing course display abnormal water temperature on the panel , after draining the

water.

3. Overview of the Washing Machine

4. Overview of the control panel

S803J

1. Detergent dispenser

2. Display panel

Displays the remaining wash cycle time and error messages.

3. Wash Button

Press the button repeatedly to cycle through the available partial wash options

{Eco

Note

4. Rinse Button

Press the button repeatedly to cycle through the available partial rinse options (Water

Note

→

rewash → Soak Wash → Cancel → Eco+}.

: Prewash/Eco+ is available only with Cotton, Colour, Synthetic or Delicate programs.

→ Rinse+→ Water

+Rinse

→ Cancel → Water

: Prewash/Eco+ is available only with Cotton, Colour, Synthetic or Delicate programs.

5. Spin selection button

Press the button repeatedly to cycle through the available spin speed options.

S803J no spin, rinse hold, 400, 600, 800 rpm

When pressing this button during operation, you can see the selected spin speed in the display panel.

6. Temperature selection button

Press the button repeatedly to cycle through the available water temperature options

(cold water, 30 ∞C, 40 ∞C,60∞C and 95∞C).

When pressing this button during washing, you can see the selected temperature in the display panel.

7. Delay Start button

Press the button repeatedly to cycle through the available delayed start options (from 1 hour to 24 hours in one hour increments).

8. Fuzzy Control dial

Turn the dial to select one of the nine available wash programs.

Baby Cotton, Cotton, Colour, Synthetic, Delicate, Wool, Quick, Rinse+Spin, Spin, Drain

9. Start/Pause button

Press to pause and restart programs.

(On/Off) button

10.

Press once to turn the washing machine on, press again to turn the washing machine off. If the washing machine power is left on for longer than 10 minutes without any buttons being touched, the power automatically turns off.

5. Main function

1) Auto power S/W off function

●

After power on, the auto power S/W off function automatically switches power off for you if you do not press

selection button for 10 minutes

●

After selecting the function, the auto power S/W off function automatically switches power off for you if you do

not press start/pause button for 10 minutes

●

until 5 minutes past, After finishing the last function, the auto power S/W off function automatically switches

power off for you if you do not re-select the course button or manual button

2) Door open function

●

If door is open during the operating, all operating is halted, and door error message will be displayed (2-digit

panel displays "Ed" 4-digit panel displays "door") and error melody will coming out

●

Door open error can be cleared by closing the door. the operating keeps going on

3) Rinse hold function

●

If rinse hold function selected, the operating is finished , the machine do not drain the water after last rinse

4) No spin function

●

If no spin function selected, the operating is finished after last rinse

5) Drain function

●

Drain function is over, after pumping out the water for 2 minutes , without motor rotating

6) Pre-washing function

●

Pre-washing function can be selected ,when you choice the following mode; cotton, coloreds, sythetics, delicates,

baby cotton

●

Water level/reverse time is the same with the selected course

●

Pre-washing takes about 15 minutes

7) Rinse+ function

●

This function practises rinse process once more

5. Main function

8) Power-out compensation function

●

If power is out on selected process, the process before power out is stored to EEPROM, once power is back

the process before power out continues.

●

When power is back, washing process starts from the process at the point of the power out, rinse/drain process

starts from the initial process.

POWER-OUT COMPENSATION FUNCTION PROCESS

WASHINGSTART

POWER OUT

SAVE DATA

to EEPROM

READ DATA

(PROCESS+TIME)

9) Water heater Error function

①

This function starts working, when the heater works abnormally.

(this function begins sensing the heater 2 minutes later, after the heater operating)

②

The value of the initial thermistor(A1) is compared with that of the thermistor(A2) in 2 minutes (Y=A2-A1)

- For 10 minutes, the variance of temperature(Y) is less than 2℃"E5"message is displayed on the panel.

③

The value of the initial thermistor(A1) is compared with that of the thermistor(A2) in 11 minutes (Y=A2-A1)

- For 1 minute the variance of temperature(Y) increases more than 7℃(0.3V) "E6"message is displayed on the

panel.

④

At this time heater, Error "E5 (heater do not work), E6(overheated)" is displayed and all working process off

⑤

The heater operating continues during heating hours, if washing hour is left over, the residual washing process

keeps going without heating.

POWER BACK

MICOM RESTORE

RESTART

PROCESS

RINSE/DRAIN

START

SAVE DATA

to EEPROM

RINSE/DRAIN

PROCESS

POWER OUT

POWER BACK

MICOM RESTORE

FINISH

5. Main function

10) Fuzzy washing function ( weight-sensing)

☞

After finishing initial water supply, when the fall of the water level needs supplementary water supply,

Sensing function perceives the weight with the supplementary water supply numbers and starts to work.

Under the course of Cotton, or Coloureds, if the supplementary water supply numbers become 3 - 4 times the

function is going at default condition ( high water level ), if 1-2 below that is going at middle level, if 0 below

low water level, heating hours and rinse hours depend on the above data.

ECO PRE mode is selected, the process going on at default condition.

Washing hours

Cotton Coloureds

High Default Default Default

Middle Default-12 min Default-7min 22.80KHZ

Low Default-25 min Default-15min 23.30KHZ

※

After sensing weight, above hours is decreased from above default hours

11) Bubble -detecting function

At the each condition of washing&dehydrating , rinse&dehydrating , hydrating, bubble -detecting function works,

this function works 5times normally, if the function detects bubbles at 6 times , the bubble-detecting function

stops and go on to the next process.

●

The bubble-detecting function during washing & dehydrating to rinse & dehydrating

after 2 times instant dehydrating and before main dehydrating, if the water level is under 25.45KHZ, Bubble

→

Detecting function thinks there are bubbles and add the bubbles-removing rinse, needing hours are above

hours and 8 min 40 sec.

→

The bubble-detecting function during single hydrating process

after 2 times instant dehydrating and before main dehydrating , if the water level is 25.45KHZ below or

during main dehydrating, water level data is 23.80KHZ below Bubble-detecting function thinks there are

bubbles and add the bubbles-removing rinse 1 times, needing hours are above hours and 5 min 55 sec.

Rinse water level

Bubble-detecting function operating process

20 sec

laundry scattering

draining &reverse

1min

unbalance

detecting range

600rpm

500rpm

bubble detection

(default water level 25.45KHZ below)

5. Main function

12) Unbalance detecting & laundry balance positioning system

①

Just before the hydrating process and just after reversal rotation for balancing laundry position, this function is

carried out

②

The initial 6 sec is the period of reversal rotation for balancing laundry position , Drum rotates 50rpm for

initial 6 sec

③

Next 10 sec, the rotation increases the speed from 50 rpm to 90 rpm slowly

④

During the next 18 sec, drum rotates at the speed of 90 rpm, the sensor decides the degree of laundry

unbalance with TACHO data which is attached to motor

⑤

If the degree of unbalanced laundry is over 6 times to default value, laundry balancing system carries out

feed back process 6 times

Unbalance detecting & laundry balance positioning system

600rpm

500rpm

20 sec

laundry scattering

unbalance

detecting range

90rpm

13) R.P.M control

The rotating motor enables the magnetics( i.e generator) to generate magnetic flux in proportion to r.p.m,

magnetic flux induced by coil sensor in the opposite side produces the wave like the figure below to and

via rectangual wave generating circuit, the waves reaches MICOM and micom controls r.p.m with the pulse,

count and cycle inputted by program.

V(VOLT)

T (HOUR)

6. Technical point

1) Motor on/off time at each course

Washing Rinse

Course

Cw Off Ccw Off Cw Off Ccw Off

Baby cotton Cotton Coloureds

Synthetics Delicates Wools Quick

※

Motor on/off time is measured in cold water, in heating time motor on/off time is 10 sec on and 5sec off in

the cotton course, beside cotton course, in the other course motor on/off time is the same with that of cold

water use.

5 15 5 15 5 15 5 15 45

13 3 13 3 10 5 10 5 50

11 4 11 4 10 5 10 5 50

7 8 7 8 7 8 7 8 40

5 10 5 10 5 10 5 10 30

2 58 2 58 2 28 2 28 25

12 3 12 3 10 5 10 5 45

2) Final dehydrating r.p.m at each course

unit:sec

Motor r.p.m

unit:rpm

Model

Course

Baby cotton Cotton Coloureds Synthetics Delicates Wools Quick

※

You can change the r.p.m to the above a table by use spin button under no spin situation.

3) The water supply control at each process cycle

Process cycle

Washing Rinse

Model

Cold water 4.5L/min + cold 10L/min

S803J

800

600

400

800

Final rinse

Cold water 4.5L/min + cold 10L/min + cold 2L/min

6. Technical point

4) The water level data at each course

Course

Baby cotton

Cotton

Coloureds

Synthetics

Delicates

Wools

Quick

Water level

Washing Rinse

Washing

Rinse

Washing Rinse Washing Rinse Washing Rinse Washing Rinse Washing Rinse

Default water level(khz)

23.50 24.00 23.70

22.45 24.00 23.50

23.50 24.00 23.70

large 22.45

small 23.30

23.50 24.00 23.70

22.45 24.00 23.50

23.50 24.00 23.70

22.45 24.00 23.50

22.80 23.55 23.35

22.65 23.55 23.35

22.45 23.35 23.00

22.15 23.35 23.00

23.50 24.00 23.70

22.45 24.00 23.50

Supplemetary w ater

START(Khz)

24.00 23.50middle 22.80

unit:Khz

Supplemetary w ater

end(khz)

5) The other water level data

The water data unter each conditon 1st water supply (only preparation) Overflow error

Bubble detectingatwashing/rinse/dehydrating

Bubble detecting rinse water level Water level which can open door Water level w hich can drive heater Water level which can reset the drain

※

If water level is 15KHZ below or 30 KHZ above , sensor-pressur is out of order so needs changing.

24.60 1st water supply level to washing tub

20.50 The water supplied reach 2/3 of door

25.45 Bubble -detecting water level

22.00 The water level which can detect bubbles

over

23.80

24.50 Safety water level of wash heater

24.50 The water level can be detected after 1st draining

It is possible to open the door

unit:Khz

+ 23 hidden pages