PDP-TELEVISION
(PLASMADISPLAYPANEL)
Owner’s Instructions
Before operating the unit, please read this manual thoroughly, and retain it for future reference.
ON-SCREEN MENUS
Picture In Picture (PIP)
Energy Saving
TELETEXT (Option)
SRS TruSurround XT
Digital Natural Image engine
Register your product at www.samsung.com/global/register Record your Model and Serial number here for future reference.
▪ Model _______________ ▪ Serial No. _______________
Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.
Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height so do not install and operate there.
Heat on the top of the PDP TV
The top side of the product may be hot after long period of use as heat dissipates from the panel through the vent hole in the upper part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children should be prevented from touching the upper part of the product.
The product is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as temperature or humidity. This is normal and not a defect of the unit.
Cell Defects
The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require sophisticated technology to produce. However, there may be few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product.
Avoid operating the TV at temperatures below 5°C(41°F)
A still image displayed too long may cause permanent damage to the PDP Panel.
Watching the PDP TV in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and centre of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause similar effect to the screen. Damages caused by the above effect are not covered by the Warranty.
Afterimage on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may produce partial afterimages. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.
Warranty
-Warranty does not cover any damage caused by image retention.
-Burn-in is not covered by the warranty.
Installation
Be sure to contact an authorized service centre, when installing your set in a location with heavy dust, high or low temperatures, high humidity, chemical substance and where it operates continually such as the airport, the train station etc. Failure to do so may cause a serious damage to your set.
Any functions related to Digital TV (DVB) will only work in countries or areas where DVB-T (MPEG2) digital terrestrial signals are broadcasted. Please confirm with your local dealer if you can receive DVB-T signals. Although this TV set follows the DVB-T specification, maintaining compatibility with the future coming DVB-T digital terrestrial broadcasts is not guaranteed. Several functions may not be available in some countries.
© 2007 Samsung Electronics Co., Ltd. All rights reserved.
English - 2
Contents |
|
General Information |
|
User Instructions............................................. |
2 |
Checking Parts................................................ |
4 |
Using the Stand-Base..................................... |
4 |
Control Panel ................................................. |
5 |
Connection Panel............................................ |
6 |
Viewing the Remote Control........................... |
8 |
Operation |
|
Switching Your Television On and Off............. |
9 |
Plug & Play Feature...................................... |
10 |
Viewing the Display....................................... |
11 |
Viewing the Menus........................................ |
12 |
Using the TOOLS Button .............................. |
12 |
Viewing External Signal Sources.................. |
13 |
Editing Device Names................................... |
14 |
Using the DTV Feature |
|
Setting the Guide.......................................... |
15 |
Setting the Default Guide.............................. |
15 |
Checking the Digital-Signal Strength - Digital.. |
16 |
Channel Control |
|
Storing Channels Automatically.................... |
16 |
Storing Channels Manually........................... |
17 |
Managing Channels...................................... |
18 |
Fine Tuning Channel Reception.................... |
24 |
LNA (Low Noise Amplifier)............................ |
25 |
Picture Control |
|
Changing the Picture Standard..................... |
26 |
Customizing the Picture Settings.................. |
27 |
Configuring Detailed Settings on the Picture .. |
28 |
Selecting the Picture Size............................. |
29 |
Digital NR / Active Colour / DNIe .................. |
30 |
Freezing the Current Picture......................... |
30 |
Viewing Picture-in-Picture............................. |
31 |
Sound Control |
|
Sound Features ............................................ |
33 |
Selecting the Sound Mode |
|
(depending on the model)............................. |
34 |
Function Description |
|
Setting the Time............................................ |
35 |
Menu Transparency / Energy Saving / HDMI Black Level / Film Mode /
Light Effect(PS50P91FD/PS58P91FD) /
Blue Screen / Melody / Function Help........... |
37 |
Activating the Child Lock............................... |
38 |
Setting the Subtitle........................................ |
39 |
Using the Game Mode.................................. |
40 |
Setting up the Parental Lock......................... |
41 |
Screen Burn Protection................................. |
43 |
Wallmount adjustment (Sold separately) |
|
(PS50P91FD/PS58P91FD)........................... |
44 |
Upgrading the Software................................ |
45 |
Over the Air Download................................... |
46 |
PC Display |
|
Setting up Your PC Software |
|
(Based on Windows XP)............................... |
47 |
Display Modes .............................................. |
48 |
Setting the PC............................................... |
49 |
Changing the Picture Size (PC Mode).......... |
50 |
Setting the Home theatre PC........................ |
50 |
WISELINK |
|
Using the WISELINK Function...................... |
51 |
Using the WISELINK Mode........................... |
52 |
Using the Photo (JPEG) List......................... |
53 |
Using the Music (MP3) List........................... |
61 |
About Anynet+ |
|
What is Anynet+?.......................................... |
64 |
Connecting Anynet+ Devices........................ |
64 |
Setting Up Anynet+....................................... |
65 |
Scanning and Switching between Anynet+ |
|
Devices......................................................... |
66 |
Recording...................................................... |
67 |
Listening through a Home theatre................. |
68 |
Troubleshooting for Anynet+......................... |
68 |
Appendix |
|
Teletext Feature (depending on the model).. |
69 |
Setting Up Your Remote Control................... |
71 |
Wall Mount Kit Specifications (VESA)........... |
76 |
How to assemble the Stand-Base |
|
(depending on the model)............................. |
77 |
Troubleshooting ............................................ |
77 |
Specifications................................................ |
78 |
Symbols |
|
|
Press |
Important |
Note |
|
English - 3 |
|
Owner’s Instructions |
Remote Control/ |
Power Cord |
Cloth-Clean |
|
AAABatteries |
|
|
Warranty Card/ |
Cover-Bottom / Screws (2ea) |
Ferrite Core for Power Cord/ |
Registration Card/ |
(Refer to page 77) |
Ferrite Core for |
Safety Guide Manual |
|
Headphones Cable |
Sold Separately
S-Video Cable |
Antenna Cable |
Component Cables |
Audio Cables |
Video Cable |
|
PC Cable |
PCAudio Cable |
HDMI Cable |
HDMI/DVI Cable |
Ferrite Core (Power Cord, Headphones Cable) |
|
|||
|
The ferrite core is used to shield the cable from interference. |
|
||
|
When connecting a cable, open the ferrite core and bind cable |
|
||
|
round the ferrite core to secure it around the cable. |
|
||
Using the Stand-Base |
|
|
||
|
Two or more people should carry |
|
|
|
|
the PDP. Never lay the PDP on the |
|
|
|
|
floor because of possible damage |
|
|
|
|
to the screen. Always keep the |
|
|
|
|
PDP upright. |
|
|
|
|
The PDP can rotate 20 degrees in |
|
|
|
|
right and left directions. |
|
-20° ~ 20° |
|
|
|
|
|
English - 4
Front (or Side) Panel
PS50P91FD/
PS58P91FD
PS63P71FD
The product colour and shape may vary depending on the model.
1SOURCE
Displays a menu of all of the available input sources (TV, AV1, AV2, S-Video, Component1, Component2, PC, HDMI1, HDMI2/DVI, and HDMI3, USB).
In the on-screen menu, use this button as you would use the ENTER/OK button on the remote control. (PS50P91FD)
2MENU
Press to see the on-screen menu of your TV’s features.
3+ VOL −
Press to increase or decrease the volume. In the on-screen menu, use the + VOL − buttons as you use the ◄ and ► buttons on the remote control.
4 CH
Press to change channels. In the on-screen menu, use the CH
buttons as you use the ▲ and ▼ buttons on the remote control.
5 (ENTER)
Press to confirm a selection.(PS63P71FD)
6 (Power) button
Press to turn the TV on and off.
Power Indicator
−Power Off: Blue/Red(PS50P91FD/PS58P91FD)
−Power On: Off
Remote Control Sensor
Aim the remote control towards this spot on the TV.
7 Speaker
English - 5
Side Panel
1
2
or
3
The product colour and shape may vary depending on the model.
1 |
HDMI IN 3 |
3 Headphones jack |
|
Connect to the HDMI jack of a device with |
You can connect a set of headphones if you |
|
HDMI output. |
wish to watch a television programme without |
2 |
S-VIDEO or VIDEO / AUDIO L/R |
disturbing the other people in the room. |
|
Video (S-Video or Video) and audio inputs for |
Prolonged use of headphones at a high |
|
external devices, such as a camcorder or VCR. |
volume may damage your hearing. |
Rear Panel |
|
1 |
|
or |
9 |
Cable Television |
|
|
Network |
3 |
|
|
or |
2 |
4 |
5 |
6 |
7 |
8 |
The product colour and shape may vary depending on the model.
Whenever you connect an audio or video system to your set, ensure that all elements are switched off.
When connecting an external device, match the colour of the connection terminal to the cable.
Continued...
English - 6
1POWER IN
Connect the supplied power cord.
2Connecting external Audio Devices
Connect RCA audio signals from the TV to an external source, such as Audio equipment.
3SERVICE
−Connector for service.
−Connect the serial jack between the electromotion wall mount bracket and your TV when you want to adjust the TV viewing angle using your remote control.
4VIDEO / AUDIO L/R
Video and audio inputs for external devices, such as a camcorder or VCR.
9ANT IN
75Ω Coaxial connector for Aerial/Cable
Network.
Supported modes for HDMI and Component
|
480i |
480p |
576i |
576p |
720p |
1080i |
1080p |
HDMI/ |
X |
X |
X |
O |
O |
O |
O |
DVI 50Hz |
|||||||
HDMI/ |
X |
O |
X |
X |
O |
O |
O |
DVI 60Hz |
|||||||
Component |
O |
O |
O |
O |
O |
O |
O |
5COMPONENT IN 1, COMPONENT IN 2
Audio (AUDIO L/R) and video (Y/PB/PR) inputs for Component.
6DIGITAL AUDIO OUT (OPTICAL)
Connect to a Digital Audio Component. According to the received audio signal, optical output is selectcted by Dobly or PCM signal. The level of sound can change according to received signal and sound level's difference can be.
7PC IN / AUDIO
Connect to the video and audio output jack on your PC.
8HDMI IN 1, HDMI IN 2
−Connect to the HDMI jack of a device with HDMI output. These inputs can also be used as a DVI connection with separate analog audio inputs. An optional HDMI/DVI cable will be necessary to make this connection. When using the optional HDMI/DVI adapter, the DVI analog audio inputs on your TV allow you to receive left and right audio from your DVI device. (Not compatible with PC)
−When connecting this product via HDMI or DVI to a Set Top Box, DVD Player or Games
Console etc, make sure that it has been set to a compatible video output mode as shown in the table below. Failure to observe this may result in picture distortion, image breakup or no picture.
−Do not attempt to connect the HDMI/DVI
connector to a PC or Laptop Graphics Card. (This will result in a blank screen being displayed)
DVI IN (HDMI 2) AUDIO L/R
DVI audio outputs for external devices. The external devices that support lower
version HDMI mode may not implement sound ouput for theTV with the latest HDMI version (HDMI 1.3.) In this case, connect to HDMI IN2 and DVI IN (HDMI 2) “ R-AUDIO-L” on the back panel of the TV.
Part of lower version HDMI cables may cause annoying flickers or no screen display in this case use the cable that supports the latest HDMI version(HDMI 1.3).
English - 7
This is a special remote control for the visually impaired persons, and has Braille points on the Power, Channel, Volume, STOP, and PLAY/PAUSE buttons.
The performance of the remote control may be affected by bright light.
1POWER button
(turns the TV on and off)
2Number buttons for direct channel access
3One/Two/Three-digit channel selection
4 Channel control button
5This function enables you to view and play photo (JPEG) and audio files (MP3) from an external device.
6 Volume increase
Volume decrease
7 Temporary sound switch-off
8Displays the main on-screen menu
9Returns to the previous menu
@ Picture size selection
#Electronic Program Guide (EPG) display
$ Sound mode selection % Remote control setup
^Selects a target device to be controlled by the Samsung remote control (TV, DVD, STB, CABLE, VCR)
&Press to backlight the VOL, CH, and the active source button (TV, DVD, CABLE,
STB, VCR) on the remote.
* Available source selection
( Previous channel
)Press to switch to your favourite channels.
aRecords for Live Broadcasting
bVCR/DVD Function (Rewind, Stop, Play/Pause, Fast/ Forward)
c Next channel
Previous channel
d Exit the on-screen menu
eControl the cursor in the menu
fUse to see information on the current broadcast
gTOOLS : Use to quickly select frequently used functions.
Anynet+ : Runs the Anynet+ view functions and sets up Anynet+ devices.
h Picture-In-Picture On/Off i Picture effect selection
j Digital subtitle display k Picture freeze
lIf your remote control is not functioning properly, take out the batteries and press the reset button for about 2~3 seconds.
Reinsert the batteries and try using the remote control again.
Teletext Functions
8 Teletext index
9Exit from the teletext display (depending on the model)
0 Fastext topic selection
!Teletext display/mix both teletext information and the normal broadcast
@ Teletext size
*Teletext mode selection (LIST/FLOF)
( Teletext sub page
cP :Teletext next page
P :Teletext previous page
d Teletext cancel f Teletext reveal h Teletext hold i Teletext store
English - 8
Installing Batteries in the Remote Control
1Lift the cover at the back of the remote control upward as
shown in the figure.
2 Install two AAA size batteries.
Make sure to match the “+” and “–” ends of the batteries with the diagram inside the compartment.
Do not mix battery types, i.e. alkaline and manganese. 3 Close the cover as shown in the figure.
Remove the batteries and store them in a cool and dry place if you won’t be using the remote control for a long time. The remote control can be used up to about 23 feet from the TV. (Assuming typical TV usage, the batteries last for about one year.)
If the remote control doesn’t work! Check the following: 1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed? 3. Are the batteries drained?
4. Is there a power cut, or is the power cord unplugged? 5. Is there a special fluorescent light or a neon sign nearby?
The main lead is attached to the rear of the television. 1 Plug the main lead into an appropriate socket.
The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.
2 Press the (Power) button (On/Off) on the front of the television or press the POWER button on the remote control to switch the television on. The programme that you were watching last is reselected automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Storing Channels Automatically” on page 16 or “Storing Channels Manually” on page 17.
If the television is initially powered on, several basic customer settings proceed automatically. Refer to “Plug & Play Feature” on page 10.
3To switch the television off, press the (Power) button (On/Off) on the front of the television or press the POWER button on the remote control.
4To switch the TV on, press the (Power) button (On/Off) on the front of the TV or press the POWER button or number buttons on the remote control.
English - 9
When the TV is initially powered on, basic settings proceed automatically:
1Press the POWER button on the remote control. The message Runs the Plug & Play function when
setting the TV up for the first time or when resetting it. Sets the channels, the clocks, as well as other functions.is automatically displayed.
2The message Select Home Mode when installing this TV at home. is automatically displayed.
3Press the ◄ or ► button to select Shop or Home, then press the ENTER/OK button.
The default selection is Home.
We recommend setting the TV to Home mode for the best picture in your home environment.
Shop mode is only intended for use in retail environments.
If the unit is accidentally set to Shop mode, and you want to return to Dynamic (Home) mode, press the Volume button and then hold down the MENU button for five seconds on the TV panel.
4The TV will begin memorizing all of the available channels.
After all the available channels are stored, the Auto program menu reappears.
Press the ENTER/OK button when channel memorization is complete.
The Clock Mode menu is displayed.
To stop the search before it has finished, press the ENTER/OK button with stop selected.
5Press the ENTER/OK button.
Press the ▲ or ▼ button to select Manual for setting the current time manually, then press the ENTER/OK button. The message Set current date and time. is displayed.
If you select Auto. Select the time zone in which you live. is displayed, then go to step 8.
6Press the ◄ or ► button to move to Month, Day, Year, Hour, Minute or am/pm.Set the date and time you want bypressing the ▲ or ▼ button, then press the ENTER/OK button.
You can set the month, day, year, hour, and minute directly by pressing the number buttons on the remote control.
7The message Enjoy your watching. is displayed.
When you have finished, press the ENTER/OK button.
Even if the ENTER/OK button is not pressed, the message will automatically disappear after several seconds.
Plug&Play
Runs thePlug&Playfunctionwhen setting theTV up for the first time or when resetting it.Sets the channels,clocks, as well as other functions.
|
|
OK |
|
|
|
|
|
Enter |
Return |
|
Plug&Play |
|
||
SelectHomeModewheninstallingthisTVathome. |
||||
|
Shop |
|
Home |
|
|
Move |
Enter |
Skip |
|
|
Plug&Play |
|
||
PressEntertostartchannelmemory. |
|
|||
|
|
|
|
0% |
|
|
Start |
|
|
|
|
|
Enterf |
Skip |
|
Plug&Play |
|
||
AutoStoreinProgress. |
DigitalChannelfound:0 |
|||
6 |
|
|||
|
|
|
|
3% |
DigitalChannelsareaddedonthefavourite |
||||
channellist. |
|
|
|
|
|
|
Stop |
|
|
|
|
|
Enter |
Skip |
|
Plug&Play |
|
||
AutoStoreiscompleted. |
|
|
||
3channelsarememorized. |
|
|||
Digital:1 |
Analog:2 |
|
|
|
|
|
OK |
|
|
|
|
|
Enter |
Skip |
|
Plug&Play |
|
||
SettheClockMode. |
|
|
|
|
|
|
|
|
|
ClockMode |
|
:Auto |
|
|
|
|
|
Enter |
Skip |
|
Plug&Play |
|
||
SettheClockMode. |
|
|
|
|
|
|
|
|
|
ClockMode |
|
: Auto |
|
|
|
|
|
Manual |
|
|
Move |
Enter |
Skip |
Plug&Play
Setcurrentdateandtime |
|
|
Month |
Day |
Year |
01 |
01 |
2007 |
Hour |
Minute |
am/pm |
00 |
04 |
am |
Move
Adjust
Enter
Skip
English - 10 |
Continued... |
|
Plug&Play
Selectthetimezoneinwhichyoulive.
NewSouthWales/ACT
Victoria
QueenSland
SouthAustralia
WestAustralia
Tasmania
Move
Enter
Skip
Plug&Play
Enjoyyourwatching.
OK
ATV
3No Time Information
1 With the power on, press the MENU button. |
|
The main menu will appear at the bottom of the screen. |
Picture |
There are seven menu groups: Picture, Sound, Channel, |
|
Setup, Input, Guide, and PIP. |
2Press the ▲ or ▼ button, then press the ENTER/OK button to select an item you want in the menu. Press the
▲/▼/◄/►/ENTER/OK button to display, change, or use the selected items.
3Press the EXIT button to exit.
The Tools button allows you to display frequently used Menu and Connection items with a Single button press.
1Press the TOOLS button. The TOOLS menu will appear.
2Press the ▲/▼ button to select a menu, then press the
ENTER/OK button.
3Press the ▲/▼/◄/►/ENTER/OK buttons to display, change, or use the selected items.
For a more detailed description of each function, refer to the corresponding page.
Device List, see page 63 Picture Setting, see page 27 Sound Setting, see page 33 Sleep Timer, see page 36
Delete Favourite Channel, see page 20 Auto Store, see page 16
Mode |
:Dynamic |
Contrast |
:100 |
Brightness |
:45 |
Sharpness |
:75 |
Colour |
:55 |
Tint(G/R) |
:G50/R50 |
ColourTone |
:Cool1 |
DetailedSettings |
|
TOOLS
DeviceList |
|
|
PictureSize |
: |
16:9 |
PictureMode |
: |
Dynamic |
SoundMode |
: |
Standard |
SleepTimer |
: |
Off |
DeletefromFavourite |
|
|
AutoStore |
|
|
|
Move |
Enter |
English - 12
Viewing External Signal Sources |
|
||
You can switch between viewing signals from connected |
|
||
equipment, such as a VCR, DVD, Set-Top Box, and the TV |
|
||
source (broadcast or cable). |
Input |
||
1 |
Press the MENU button to display the menu. |
||
|
2Press the ▲ or ▼ button to select Input, then press the
ENTER/OK button.
3 Press the ENTER/OK button again to select Source List.
4Press the ▲ or ▼ button to select the signal source, then press the ENTER/OK button.
Available signal sources: TV, AV1, AV2, S-Video,
Component1, Component2, PC, HDMI1, HDMI2/DVI, HDMI3, USB
You can select these options simply by pressing the SOURCE button on the remote control.
SourceList
EditName
TV
AV1 |
---- |
AV2 |
---- |
S-Video |
---- |
Component1 |
---- |
Component2 |
---- |
PC |
---- |
|
|
Refresh |
Option |
English - 13
You can give a name to the external source.
1Press the MENU button to display the menu.
2Press the ▲ or ▼ button to select Input, then press the
ENTER/OK button.
3Press the ▲ or ▼ button to select Edit Name, then press the ENTER/OK button.
4Press the ▲ or ▼ button to select the external source to be edited, then press the ENTER/OK button.
5Select the required device by pressing ▲ or ▼, then press the ENTER/OK button.
Available device names: VCR, DVD, D-VHS, Cable STB,
HD STB, Satellite STB, PVR STB, AV Receiver, DVD Receiver, Game, Camcorder, DVD Combo, DVD HDD Recorder, PC, Internet TV Recv., Interactive TV Recv., VOD STB, TV.
6Press the EXIT button to exit.
When a PC with a resolution of 1920 x 1080@60Hz is connected to the HDMI IN 1 port, you should set the HDMI1 mode to PC in the Source List of the Input mode. If the HDMI1 mode is not PC, it works depending on the TV setting.
SourceList
Input |
EditName |
|
|
EditName
AV1 |
:---- |
|
|
AV2 |
:---- |
|
|
S-Video |
:---- |
|
|
Component1 |
:---- |
|
|
Component2 |
:---- |
|
|
PC |
:---- |
|
|
HDMI1 |
:---- |
|
|
|
|
|
|
|
Move |
Enter |
Return |
EditName
AV1 |
: |
---- |
|
AV2 |
: |
VCR |
|
S-Video |
: |
DVD |
|
Component1 |
: |
D-VHS |
|
Component2 |
: |
CableSTB |
|
PC |
: |
HDSTB |
|
HDMI1 |
: |
|
|
|
|
|
|
|
Move |
Enter |
Return |
English - 14
You can set the guide as your preference.
1Press the MENU button to display the menu.
2Press the ▲ or ▼button to select Guide. Press the
ENTER/OK button.
3Select your required guide (Now & Next Guide or Full Guide) by pressing the ▲ or ▼ button.
4Press the ENTER/OK button.
5Select a programme of your choice by pressing the ▲, ▼, ◄, or ► button.
6Press the INFO button to display information about the highlighted programme.
7Press the red button to exchange Now & Next Guide or
Full Guide.
8Press the EXIT button or blue button to exit.
WISELINK
Guide |
FullGuide |
|
|
|
|
|
Now&NextGuide |
|
|
DefaultGuide |
:FullGuide |
Full Guide
|
|
DTV 77 Digital |
|
|
|
|
|
|
NBC TODAY |
|
|
|
|
|
|
AM 4:00 - AM 6:00 |
|
|
|
|
77 Digital |
|
International news and weather. Including interviews with ne.. |
||||
|
|
|
|
|
|
|
Today |
|
AM6:00-AM7:00 |
|
AM7:00-AM8:00 |
|
|
7 Digital |
NBC TODAY |
|
SUNRISE |
|
||
7 HD Digital |
NBC TODAY |
|
SUNRISE |
|
||
7 Digital 1 |
NBC TODAY |
|
SUNRISE |
|
||
7 Digital 2 |
NBC TODAY |
|
SUNRISE |
|
||
7 Digital 3 |
NBC TODAY |
|
SUNRISE |
|
||
7 Guide |
NBC TODAY |
|
SUNRISE |
|
||
Watch |
INFO |
Info Now&Next |
-2Hours |
+2Hours |
Exit |
You can preset the default guide style.
1Press the MENU button to display the menu.
2Press the ▲ or ▼button to select Guide. Press the
ENTER/OK button.
3Press the ▲ or ▼ button to select Default Guide, then press the ENTER/OK button.
4Select Now/Next or Full Guide using the ▲ or ▼ button, and press the ENTER/OK button.
5Press the EXIT button to exit.
You can select these options by simply pressing the GUIDE button on the remote control.
Guide
FullGuide
Now&NextGuide
DefaultGuide |
: Now&Next |
|
FullGuide |
English - 15
Unlike analog channels, which can vary in reception quality from “snowy” to clear, digital (HDTV) channels have either perfect reception quality or you will not receive them at all. So, unlike analog channels, you cannot fine tune a digital channel.
You can, however, adjust your antenna to improve the reception of available digital channels.
1Press the MENU button to display the menu.
2Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button.
3Press the ▲ or ▼ button to select Signal Strength, then press the ENTER/OK button.
4If the signal strength meter indicates that the signal is weak, physically adjust your antenna to increase the signal strength.
Continue to adjust the antenna until you find the best position with the strongest signal.
5Press the EXIT button to exit.
Channel
ManualStore
FineTune
SignalStrength |
|
LNA |
:On |
SignalStrength
OK
Enter
Return
You can scan for the frequency ranges available to you |
|
|
|
|
(availability depends on your country). |
|
ChannelList |
|
|
Automatically allocated programme numbers may not |
Channel |
AutoStore |
|
|
correspond to actual or desired programme numbers. |
||||
However you can sort numbers manually and clear any |
|
ManualStore |
|
|
channels you do not wish to watch. |
|
FineTune |
|
|
1 |
Press the MENU button to display the menu. |
|
SignalStrength |
|
2 |
Press the ▲ or ▼ button to select Channel, then press the |
|
LNA |
:On |
|
ENTER/OK button. |
|
|
|
3 |
Press the ▲ or ▼ button to select Auto Store, then press |
|
|
|
|
the ENTER/OK button. |
|
|
|
4Press the ENTER/OK button again to start the search. The search will end automatically.
To stop the search before it has finished, press the MENU or the ENTER/OK button.
English - 16
You can store television channels, including those |
|
ChannelList |
|
|
received via cable networks. |
|
AutoStore |
|
|
When storing channels manually, you can choose: |
Channel |
ManualStore |
|
|
Whether or not to store each of the channels found. |
||||
The programme number of each stored channel which you |
|
FineTune |
|
|
|
wish to identify. |
|
SignalStrength |
|
1 |
Press the MENU button to display the menu. |
|
LNA |
:On |
2 |
Press the ▲ or ▼ button to select Channel, then press |
|
|
|
|
the ENTER/OK button. |
|
|
|
3 |
Press the ▲ or ▼ button to select Manual Store, then |
|
|
|
|
press the ENTER/OK button. |
|
|
|
4Select the required option by pressing the ▲ or ▼ button,
|
then press the ENTER/OK button. |
|
|
ChannelList |
|
|
||
|
On digital mode, you can choose Digital Channel, on |
Channel |
AutoStore |
|
|
|||
|
|
analog mode ,you can choose Digital Channel and |
ManualStore |
: DigitalChannel |
||||
|
|
Analog Channel. |
||||||
5 |
|
FineTune |
AnalogChannel |
|||||
When you are satisfied with your setting, press the |
|
|
||||||
|
|
SignalStrength |
|
|
||||
|
ENTER/OK button. |
|
|
|
|
|||
|
|
|
LNA |
|
:On |
|||
6 |
Press the EXIT button to exit. |
|
|
|
||||
|
|
|
|
|
|
|||
Programme (Programme number to be assigned to a |
|
|
|
|
|
|
||
|
channel) |
|
|
|
|
|
|
|
|
− |
Press the ▲ or ▼ button until you find the correct |
|
|
|
|
|
|
|
|
number. |
|
|
|
|
|
|
|
|
You can also select the channel number directly by |
|
|
|
ManualStore |
|
|
|
|
pressing the numeric buttons (0~9). |
|
|
|
|
||
Colour System: Auto/PAL |
|
|
Channel |
Frequency |
|
Bandwidth |
||
|
− |
Press the ▲ or ▼ button to select the required colour |
|
|
|
|||
|
|
standard. |
|
|
|
634500 KHz |
7 MHz |
|
|
|
|
|
43 |
||||
Sound System: DK/I/BG |
|
|
|
|
|
|
||
|
− |
Press the ▲ or ▼ button to select the required sound |
|
|
|
Start |
|
|
|
|
standard. |
|
|
|
|
|
|
Channel (When you know the number of the channel to |
|
|
Adjust |
Move |
Enter |
Return |
||
|
be stored) |
|
|
|
ManualStore |
|
||
|
− |
Press the ▲ or ▼ button to select C (Air channel) or S |
|
|
|
|
||
|
|
(Cable channel). |
|
Programme |
ColourSystem |
SoundSystem |
||
|
− |
Press the ► button, then press the ▲ or ▼ button to |
|
|
|
Auto |
|
BG |
|
|
select the required number. |
|
|
1 |
|
||
|
|
You can also select the channel number directly by |
|
|
Channel |
Search |
|
Store |
|
|
pressing the numeric buttons (0~9). |
|
C |
2 |
62 MHz |
|
? |
|
|
If there is abnormal sound or no sound, reselect the |
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
sound standard required. |
|
|
Adjust |
Move |
Enter |
Return |
Search (When you do not know the channel numbers) |
|
|
||||||
|
|
|
|
|
|
|||
|
− |
Press the ▲ or ▼ button to start the search. |
|
|
|
|
|
|
|
− |
The tuner scans the frequency range until the first channel or the channel that you selected is |
||||||
|
|
received on the screen. |
|
|
|
|
|
|
Store (When you store the channel and associated programme number) − Set to OK by pressing the ENTER/OK button.
Channel mode
P (Programme mode): When completing tuning, the broadcasting stations in your area have been assigned to position numbers from P00 to P99. You can select a channel by entering the position number in this mode.
C (Air channel mode): You can select a channel by entering the assigned number to each air broadcasting station in this mode.
S (Cable channel mode): You can select a channel by entering the assigned number for each cable channel in this mode.
English - 17
Using this menu, you can Add/Delete or set Favourite channels and use the program guide for digital broadcasts.
Viewing All Channels
Show all currently available channels.
To use the Channel List function, first run Auto Program.
1Press the MENU button to display the menu.
2Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button.
3Press the ▲ or ▼ button to select Channel List, then press the ENTER/OK button.
4Press the ◄ button to select Added Channels.
5Press the ▲ or ▼ button to select All Channels, then press the ENTER/OK button.
Shows all currently available channels.
6Press the ▲ or ▼ button to select a channel to view, then press the ENTER/OK button.
You can watch the selected channel.
You can press Number buttons on Remote control for direct channel access,press the same Number button again to switch between digital channel and ATV channel.
Channel
Channels Added
Channels All
ChannelList |
|
AutoStore
ManualStore
FineTune
SignalStrength
LNA :On
1♥7HDDigital
2♥7Digital1
3♥7Digital2
4♥7Digital3
ATV0 |
C1 |
|
ATV1 |
C2 |
|
ATV2 |
C3 |
|
ATV3 |
C4 |
|
ATV4 |
C5 |
|
Zoom |
Select |
Option |
1 ♥7HDDigital
2♥7Digital1
3 ♥7Digital2
4♥7Digital3
ATV0 |
C1 |
|
ATV1 |
C2 |
|
ATV2 |
C3 |
|
ATV3 |
C4 |
|
ATV4 |
C5 |
|
Zoom |
Select |
Option |
You can select these options simply by pressing the CH LIST button on the remote control.
Using the Colour buttons on the Remote with the Channel List
Green (Zoom): Enlarges or shrinks a channel number. Yellow (Select): Selects multiple channel lists.
Blue (Option): Displays the Add (or Delete), Add Favourite (or Delete Favourite), Timer Viewing, and
Channel Name Edit menus. |
|
|
|
|
|
A gray-coloured channel refers to a deleted channel. The Add menu only appears for deleted |
|||||
channels. |
|
|
|
|
|
If you select multiple channel include “favourite |
All |
1 |
♥7HDDigital |
|
|
channels”,“delete channel etc. channels”and other |
|
||||
Channels |
2 |
7Digital1 |
Add |
||
channels, you can choose “Add to Favourite or Delete from |
|||||
3 |
♥7Digital2 |
Delete |
|||
Favourite or Add or Deselect All”etc. |
|
AddtoFavourite |
|||
|
4 |
♥7Digital3 |
|||
|
|
ATV0 |
C1 |
DeletefromFavourite |
|
|
|
DeselectAll |
|||
|
|
ATV1 |
C2 |
||
|
|
|
|||
|
|
ATV2 |
C3 |
|
|
|
|
ATV3 |
C4 |
|
|
|
|
ATV4 |
C5 |
|
|
|
|
Zoom |
Select |
Option |
Continued...
English - 18
Adding and Erasing Channels
You can add or delete a channel to display the channels you want.
1Press the MENU button to display the menu.
2 |
Press the ▲ or ▼ button to select Channel, then press the |
Channel |
|
ENTER/OK button. |
|
3 |
Press the ▲ or ▼ button to select Channel List, then |
|
|
press the ENTER/OK button. |
|
4Press the ◄ button to select Added Channels.
5Press the ▲ or ▼ button to select All Channels, then press the ENTER/OK button.
Shows all currently available channels.
6Press the ▲ or ▼ button to select a channel to add, then press the blue button.
7 |
Press the ENTER/OK button to select Add. |
|
|
All added channels will be shown on Added |
All |
|
Channels menu. |
|
8 |
Press the ▲ or ▼ button to select a channel to delete, |
Channels |
|
then press the blue button. |
|
Press the ENTER/OK button to select Delete.
9Press the EXIT button to exit.
You can also delete a channel in the Added Channels menu in the same manner.
Channels All
You can select these options simply by pressing the CH LIST button on the remote control.
ChannelList |
|
AutoStore
ManualStore
FineTune
SignalStrength
LNA :On
1♥7HDDigital
2♥7Digital1
3♥7Digital2
4♥7Digital3
ATV0 |
C1 |
|
ATV1 |
C2 |
|
ATV2 |
C3 |
|
ATV3 |
C4 |
|
ATV4 |
C5 |
|
Zoom |
Select |
Option |
1♥7HDDigital
2 |
♥7Digital1 |
Delete |
|
3 |
♥7Digital2 |
DeletefromFavourite |
|
TimerViewing |
|||
4 |
♥7Digital3 |
||
ChannelNameEdit |
|||
ATV0 |
C1 |
||
|
|||
ATV1 |
C2 |
|
|
ATV2 |
C3 |
|
|
ATV3 |
C4 |
|
|
ATV4 |
C5 |
|
|
Zoom |
Select |
Option |
Continued...
English - 19
Setting Your Favourite Channels
You can set channels you watch frequently as favourites.
1Press the MENU button to display the menu.
2Press the ▲ or ▼ button to select Channel, then press the ENTER/OK button.
3Press the ▲ or ▼ button to select Channel List, then press the ENTER/OK button.
4Press the ◄ button to select Added Channels.
5Press the▲ or ▼button to select Favourite,then press the
ENTER/OK button. You can view all favourite channels.
6Press the▲ or ▼button to select Added Channels,
then press the ENTER/OK Button.
7Press the ▲ or ▼ button to select a channel as a favourite channel, then press the blue button.
8Press the ▲ or ▼ button to select Add to Favourite, then press the ENTER/OK button.
The “♥” symbol will be displayed and the channel will be set as a favourite.
9To cancel your favourite channel selection, press the blue button when a favourite channel is selected. Press the ▲ or ▼ button to select Delete from Favourite, then press the ENTER/OK button. The channel is deleted from
Favourites and the “♥” mark also disappears.
10Press the EXIT button to exit.
You can also Add or Delete a channel from Favourites in the All Channels menu in the same manner.
Onlychannels.memorized channels can be set as favourite
All favourite channels will be shown on Favourite menu.
You can select these options simply by pressing the CH LIST button on the remote control.
Easy Setting
1Press the TOOLS button on the remote control.
2Press the ▲/▼ button to select Add to Favourite or
Delete from Favourite, then press the ENTER/OK button. The current channel is added to or deleted from Favourites.
To select the favourite channels you have set up, press the FAV.CH button on the remote control.
Channel
Channels Added
Channels Added
ChannelList |
|
AutoStore
ManualStore
FineTune
SignalStrength
LNA :On
1♥7HDDigital
2♥7Digital1
3♥7Digital2
4♥7Digital3
ATV0 |
C1 |
|
ATV1 |
C2 |
|
ATV2 |
C3 |
|
ATV3 |
C4 |
|
ATV4 |
C5 |
|
Zoom |
Select |
Option |
1♥7HDDigital
2 |
♥7Digital1 |
Delete |
|
3 |
♥7Digital2 |
DeletefromFavourite |
|
TimerViewing |
|||
4 |
♥7Digital3 |
||
ChannelNameEdit |
|||
ATV0 |
C1 |
||
|
|||
ATV1 |
C2 |
|
|
ATV2 |
C3 |
|
|
ATV3 |
C4 |
|
|
ATV4 |
C5 |
|
|
Zoom |
Select |
Option |
TOOLS
DeviceList |
|
|
PictureSize |
: |
16:9 |
PictureMode |
: |
Dynamic |
SoundMode |
: |
Standard |
SleepTimer |
: |
Off |
DeletefromFavourite |
|
|
AutoStore |
|
|
|
Move |
Enter |
Continued...
English - 20
Reserving a Program (Time Viewing)
If you reserve a program you want to watch, the channel is automatically switched to the reserved channel in the Channel List even when you are watching another channel.
To reserve a program set the current time first. See pages 35~36. Reserved channels can only be set if they are in the Channel List (See page 18).
1Press the MENU button to display the menu.
2Press the ▲ or ▼ button to select Channel, then press the ENTER/OK button.
3Press the ▲ or ▼ button to select Channel List, then press the ENTER/OK button.
4Press the ▲ or ▼ button to select a channel, then press the Blue (Options) button.
5Press the ▲ or ▼ button to select Timer Viewing, then press the ENTER/OK button.
The Reserve a Program (Timer Viewing) screen appears.
6Press the ▲/▼/◄/► buttons to reserve a program and then press the ENTER/OK button.
Reserving a program has been completed.
7Press the EXIT button to exit.
You can also reserve a program in the All Channels or Favourite menus using the same procedures.
For information on how to confirm a viewing reservation, refer to page 22.
Channel
Channels Added
ChannelList |
|
AutoStore |
|
ManualStore |
|
FineTune |
|
SignalStrength |
|
LNA |
:On |
1♥7HDDigital
2♥7Digital1
3♥7Digital2
4♥7Digital3
ATV0 |
C1 |
ATV1 |
C2 |
ATV2 |
C3 |
ATV3 |
C4 |
ATV4 |
C5 |
Delete
DeletefromFavourite
TimerViewing
ChannelNameEdit
Zoom |
Select |
Option |
|
TimerViewing |
|
|
Antenna |
Channel |
Repeat |
|
DTV |
2 |
once |
|
Date |
|
StartTime |
|
2007-01-10 |
10:09am |
|
|
Move |
Adjust |
Enter |
Return |
You can select these options simply by pressing the CH LIST button on the remote control.
Digital Program Guide and Viewing Reservation
When a digital channel is selected, and you press the ► button, the Program Guide for the channel appears. You can reserve a program according to the procedures described above.
: A program currently being broadcast.
: A reserved program
Channels Added
1 |
♥7HDDigital |
2007/2/3 |
||
2 |
♥7Digital1 |
|
1:30 |
am |
3 |
♥7Digital2 |
|
2:27 |
am |
4 |
♥7Digital3 |
|
2:35 |
am |
ATV0 |
C1 |
|
3:21 am |
|
ATV1 |
C2 |
|
4:33 am |
|
ATV2 |
C3 |
|
6:00 am |
|
ATV3 |
C4 |
|
6:36 am |
|
ATV4 |
C5 |
|
|
|
Zoom |
Option |
Watch |
|
|
Continued...
English - 21
Confirming a Viewing Reservation
You can view, modify or delete a reservation.
1Press the MENU button to display the menu.
2Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button.
3Press the ▲ or ▼ button to select Channel List, then press the ENTER/OK button.
4Press the ◄ button to select Added Channels.
5Press the ▲ or ▼ button to select Programed, then press the ENTER/OK button.
You can view reservations.
Channel
ChannelList |
|
AutoStore
ManualStore
FineTune
SignalStrength
LNA :On
Channels Added
1♥7HDDigital
2♥7Digital1
3♥7Digital2
4♥7Digital3
ATV0 |
C1 |
|
|
ATV1 |
C2 |
|
|
ATV2 |
C3 |
|
|
ATV3 |
C4 |
|
|
ATV4 |
C5 |
|
|
|
Zoom |
Select |
Option |
Programed
2007/2/3 |
|
|
|
3:15 |
am |
6-1 |
NoProgramName |
4:15 |
am |
6-1 |
NoProgramName |
2007/2/4 |
|
|
|
2:14 |
am |
6-1 |
NoProgramName |
2007/2/5 |
|
|
|
2:15 |
am |
6-1 |
NoProgramName |
Zoom |
Select |
Option Information |
Modifying a viewing reservation |
|
|
6To select a reservation item to be modified, press the ▲
7 |
or ▼ button and then press the blue button. |
Programed |
2007/2/3 |
|
|
|
|
Press the ENTER/OK button to select Change Info. |
3:15 |
am |
6-1 |
|
ChangeInfo |
||
|
|
|
|
||||
8 |
Press the ▲/▼/◄/► buttons to change a reservation |
|
4:15 |
am |
6-1 |
|
Cancelschedules |
|
|
Information |
|||||
|
2007/2/4 |
|
|
||||
|
setting and then press the ENTER/OK button. |
|
2:14 |
am |
6-1 |
|
NoProgramName |
|
The reservation modification is applied. |
|
2:15 |
am |
6-1 |
|
NoProgramName |
|
|
|
2007/2/5 |
|
|
|
|
Cancelling a reservation |
|
|
|
|
|
|
|
6 |
To select a reservation item to be cancelled, press the ▲ |
|
|
|
Zoom |
Select |
Option Information |
|
|
|
|
|
or ▼ button, and then press the blue button.
7 Press the ▲ or ▼ button to select Cancel schedules, then press the ENTER/OK button.
8Press the ◄ or ► button to select OK, then press the ENTER/OK button. The viewing reservation has been cancelled.
9Press the EXIT button to exit.
Programed Menu
Change Info: Select to change a viewing reservation.
Cancel schedules: Select to cancel a viewing reservation.
Information: Select to view a viewing reservation.
You can select these options simply by pressing the CH LIST button on the remote control.
Continued...
English - 22
Labeling Channels - Analog
Channels can labeled so that their call letters appear whenever the channel is selected.
1Press the MENU button to display the menu.
2 |
Press the ▲ or ▼ button to select Channel, then press |
Channel |
|
|
3 |
the ENTER/OK button. |
ChannelList |
|
|
Press the ▲ or ▼ button to select Channel List, then |
||||
|
|
|
||
|
press the ENTER/OK button. |
|
AutoStore |
|
4 |
Press the ▲ or ▼ button to select the channel to be |
|
ManualStore |
|
|
assigned a new name, then press the blue button. |
|
FineTune |
|
5Press the ▲ or ▼ button to select Channel Name Edit, then press the ENTER/OK button.
6Press the ▲/▼/◄/► button to select a letter, then press the ENTER/OK button.
Numeric buttons: You can enter numbers.
Red button: You can switch between English and Characters.
Green button: You can delete an already entered character.
Yellow button: You can enter a blank space.
Blue button: Press this button to finish renaming a channel.
7When you have finished, press the blue button to assign the new name.
8Press the EXIT button to exit.
The names of digital broadcasting channels are automatically assigned and thus cannot be assigned by users.
Channels Added
Channels Added
SignalStrength
LNA :On
3♥7Digital2
4 |
♥7Digital3 |
|
ATV0 |
C1 |
|
ATV1 |
C2 |
|
ATV2 |
C3 |
|
ATV3 |
C4 |
|
ATV4 |
C5 |
|
ATV5 |
C6 |
|
ATV6 |
C7 |
|
Zoom |
Select |
Option |
3♥7Digital2
4♥7Digital3
ATV0 |
C1 |
Delete |
|
ATV1 |
C2 |
AddtoFavourite |
|
TimerViewing |
|||
ATV2 |
C3 |
||
ChannelNameEdit |
|||
ATV3 |
C4 |
||
|
|||
ATV4 |
C5 |
|
|
ATV5 |
C6 |
|
|
ATV6 |
C7 |
|
Zoom |
Select |
Option |
ChannelNameEdit
6_
ANumber Character Delete
Blank
VDone
Move
Enter
Return
English - 23
If the reception is clear, you do not have to fine tune the channel, as this is done automatically during the search and store operation.
If the signal is weak or distorted, you may have to fine tune the channel manually.
1Press the MENU button to display the menu.
2Press the ▲ or ▼ button to select Channel, then press the ENTER/OK button.
3Press the ▲ or ▼ button to select Fine Tune, then press the ENTER/OK button.
4To obtain a sharp, and clear picture and good sound quality, press the ◄ or ► button until you reach the optimal setting. Press the ENTER/OK button.
To reset the fine tuning to 0, select Reset by pressing the ▲ or ▼ button. Press the ENTER/OK button.
5Press the EXIT button to exit.
Fine tuned channels that have been saved are marked with an asterisk “*” on the right-hand side of the channel number in the channel banner.
AutoStore
ManualStore
Channel |
FineTune |
|
|
||
|
SignalStrength |
|
|
LNA |
:On |
FineTune
ATV6
|
|
|
0 |
|
Reset |
|
|
Move |
Adjust |
Save |
Return |
|
FineTune |
|
|
ATV6* |
|
|
FineTuned |
|
|
|
+3 |
|
Reset |
|
|
Move |
Adjust |
Save |
Return |
|
FineTune |
|
|
ATV6 |
|
|
|
|
|
|
0 |
|
Reset |
|
|
|
Move |
Enter |
Return |
English - 24