Samsung PS63A766T1, PS50A766T1, PS63A756T1W User Manual

Contact SAMSUNG WORLD-WIDE
Country
AUSTRIA 0810 - SAMSUNG(7267864, € 0.07/min) www.samsung.com/at BELGIUM 02 201 2418 www.samsung.com/be
CZECH REPUBLIC
DENMARK 8 - SAMSUNG(7267864) www.samsung.com/dk EIRE 0818 717 100 www.samsung.com/ie
ESTONIA 800-7267 www.samsung.ee FINLAND
FRANCE
GERMANY 01805 - SAMSUNG(7267864, € 0.14/Min) www.samsung.de HUNGARY 06 - 80 - SAMSUNG(7267864) www.samsung.com/hu ITALIA 800 - SAMSUNG(7267864) www.samsung.com/it KAZAKHSTAN 8-10-800-500-55-500 www.samsung.com/kz_ru KYRGYZSTAN 00-800-500-55-500 LATVIA 8000-7267 www.samsung.com/lv LITHUANIA 8-800-77777 www.samsung.lt LUXEMBURG 02 261 03 710 www.samsung.com/lu NETHERLANDS 0900 - SAMSUNG(7267864, € 0.10/Min) www.samsung.com/nl
NORWAY 3 - SAMSUNG(7267864) www.samsung.com/no
POLAND
PORTUGAL 808 20 - SAMSUNG(7267864) www.samsung.com/pt RUSSIA 8-800-555-55-55 www.samsung.ru SLOVAKIA 0800 - SAMSUNG(7267864) www.samsung.com/sk SPAIN 902 - 1 - SAMSUNG (902 172 678) www.samsung.com/es SWEDEN 075 - SAMSUNG(726 78 64) www.samsung.com/se Switzerland 0848 - SAMSUNG(7267864, CHF 0.08/min) www.samsung.com/ch TADJIKISTAN 8-10-800-500-55-500 Turkey 444 77 11 www.samsung.com/tr
U.K 0845 SAMSUNG(7267864) www.samsung.com/uk UKRAINE 8-800-502-0000 www.samsung.ua UZBEKISTAN 8-10-800-500-55-500 www.samsung.com/kz_ru
800 - SAMSUNG (800-726786) www.samsung.com/cz Samsung Zrt., česká organizační složka, Oasis Florenc, Sokolovská394/17, 180 00, Praha 8
30 - 6227 515 3260 SAMSUNG(7267864, € 0,15/Min)
0825 08 65 65 (€ 0.15/Min)
0 - 801 - 1SAMSUNG(172678) 022 - 607 - 93 - 33
Customer Care Centre
www.samsung.com/fi
www.samsung.com/fr
www.samsung.com/pl
Web Site
Plasma TV
user manual
BN68-01757B-00
imagine the possibilities
Thank you for purchasing this Samsung product. To receive more complete service, please register your product at
www.samsung.com/global/register
Model Serial No.

User Instructions

Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.
Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height so do
not install and operate there.
Heat on the top of the PDP TV
The top side of the product may be hot after long period of use as heat dissipates from the panel through the vent hole in the
upper part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children
should be prevented from touching the upper part of the product.
The product is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as
temperature or humidity. This is normal and not a defect of the unit.
Cell Defects
The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require sophisticated technology to produce. However, there may be few bright or dark pixels on the screen. These pixels will have no impact on the
performance of the product.
Avoid operating the TV at temperatures below 5°C(41°F)
A still image displayed too long may cause permanent damage to the PDP Panel.
Watching the PDP TV in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and centre of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause similar effect to the screen. Damages caused by the above effect are not covered by the Warranty.
Afterimage on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may produce partial afterimages.
To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.
Warranty
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.
Installation
Be sure to contact an authorized service centre, when installing your set in a location with heavy dust, high or low temperatures, high humidity, chemical substance and where it operates continually such as the airport, the train station etc. Failure to do so may cause a serious damage to your set.
Digital TV (DVB-T) Notice
1. FUNCTIONALITIES RELATED TO DIGITAL TV (DVB) ARE ONLY AVAILABLE IN COUNTRIES OR AREAS WHERE DVB-T (MPEG2 AND MPEG4 AVC) DIGITAL TERRESTRIAL SIGNALS ARE BROADCAST. DVB-T is the European
consortium standard for the broadcast transmission of digital terrestrial television. Please check with your local dealer about the availability of DVB-T service in your area.
2.
Although this TV set meets the current DVB-T standards as of [August, 2008], compatibility with future DVB-T digital
terrestrial broadcast cannot be guaranteed.
3. Some Digital TV functions may not be available or operate correctly in some countries or regions.
4. For more information, please contact your local SAMSUNG customer care centre.
Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care centre. (See back cover for more informations.)
© 2008 Samsung Electronics Co., Ltd. All rights reserved.
English - 2

Contents

English
Connecting and Preparing Your TV
User Instructions .................................................................2
Checking Parts ....................................................................4
Using the Stand-Base .........................................................4
How to assemble the Stand-Base
(depending on the model) ...................................................4
Viewing the Control Panel ...................................................5
Viewing the Connection Panel.............................................6
Remote Control ...................................................................8
Installing Batteries in the Remote Control ...........................9
Switching On and Off...........................................................9
Placing Your Television in Standby Mode ............................9
Viewing the Menus ............................................................10
Using the TOOLS Button ...................................................10
Using the Wheel button .....................................................10
Plug & Play Feature ..........................................................11
Channel Control
Storing Channels and channel .........................................11
Managing Channels ..........................................................15
Picture Control
Changing and Resetting the Picture Settings ....................16
Viewing Picture-in-Picture .................................................20
Setting up the TV with your PC .........................................20
PC Display .........................................................................21
Sound Control
Changing the Sound Standard ..........................................22
Selecting the Sound Mode ................................................23
Function Description
Conguring the Setup Menu ..............................................24
Setting the Time ................................................................27
Network Connection ..........................................................28
Network Setup ...................................................................30
Source List / Edit Name .....................................................32
Product Guide ...................................................................32
WISELINK Pro-DLNA
Setting the DLNA Network .................................................45
Installing the DLNA Application .........................................45
Using the DLNA Application ..............................................47
Using the DLNA Function ..................................................50
Content Library
Activating the Content Library ...........................................51
Using the Content Library ..................................................52
■ Using Additional Content Using External USB Memory
Storage ..............................................................................53
About Anynet
Connecting Anynet+ Devices ............................................54
Setting Up Anynet+............................................................55
Scanning and Switching between Anynet+ Devices..........55
Recording ..........................................................................56
Listening through a Receiver (Home theater) ...................57
Troubleshooting for Anynet+ ............................................57
+
InfoLive
Using InfoLive ....................................................................58
Using the Weather Service ................................................59
Using the News Service ....................................................59
Using the Stock Service ....................................................60
InfoLive Setup ...................................................................61
Recommendations for Use
Teletext Feature .................................................................62
Wall Mount Kit Specications (VESA) ...............................63
Auto Wall-Mount Adjustment (Sold separately) ................64
Preparing before installing Wall- Mount on the wall ..........65
Securing the TV to the Wall ...............................................65
Troubleshooting .................................................................66
Specications ....................................................................67
Additional Terms of Service ...............................................68
WISELINK Pro
Connecting a USB Device .................................................33
Using the WISELINK Pro Function ....................................34
Using and Sorting Photo List .............................................36
Viewing a Photo or Slide Show .........................................37
Using and Sorting the Music List .......................................39
Playing a Music .................................................................40
Using and Sorting the Movie List .......................................41
Playing a Movie File ..........................................................42
Deleting the Photo/Music/Movie File .................................43
Picture/Music Settings Using WISELINK Pro ....................44
Using the Setup Menu .......................................................44
N O T
Symbol Press Note One-Touch Button TOOLS
English - 3

Connecting and Preparing Your TV

Checking Parts

Owner’s Instructions Remote Control/
Cover-Bottom / Screws (2ea)
(PS50A766)
Ferrite Core (Power Cord)
N
The ferrite core is used to shield the cable from interference. When connecting a cable, open the ferrite core and clip it around the cable near the plug.
AAA Batteries
Holder-Ring (4ea) (Refer to page 65)
Power Cord Cloth-Clean Warranty Card/
Program CD Ferrite Core for Power
Cord (2ea)

Using the Stand-Base

Two or more people should carry the PDP. Never lay the PDP on the floor
N
because of possible damage to the screen. Always keep the PDP upright.
The PDP can rotate 20 degrees in right and left directions.
N
Safety Guide Manual
(Not available in all locations)
-20° ~ 20°

How to assemble the Stand-Base (depending on the model)

Using the 6 screws for securing the stand base and the monitor, firmly attach the monitor to the stand base. (The exterior of the set may be different than the picture.)
Warning
Firmly secure the stand to the TV before moving it, as the stand may fall and could cause serious injury.
Two or more people should carry the TV.
N
Never lay the TV on the floor because of possible damage to the screen.
Always store the TV upright.
English - 4
In case of installing your TV on the wall, close the cover (1) on the stand-base connection part using two screws for hiding.
English - 5

Viewing the Control Panel

The product colour and shape may vary depending on the model.
N
Front Panel buttons
Touch each button to
operate.
1
SOURCE
Toggles between all the available input sources
(TV, Ext1, Ext2, AV, S-Video, Component, PC, HDMI1,
HDMI2/DVI
N
2
MENU
Press to see an on-screen menu of your TV’s features.
+
3
Press to decrease or increase the volume. In the on-screen
menu, use the – + buttons as you would use the ◄
and ► buttons on the remote control.
4
Press to change channels. In the on-screen menu, use
the C/P. buttons as you would use the ▲ and ▼
buttons on the remote control.
5
POWER INDICATOR
Blinks and turns off when the power is on and lights up in
stand-by mode.
6
REMOTE CONTROL SENSOR
Aim the remote control towards this spot on the TV.
, HDMI3, HDMI4, USB, DLNA).
In the on-screen menu, use this button as you would
use the ENTER button on the remote control.
C/P.
7
SPEAKERS
8 (
POWER)
Touch the silver sensor below the (
on and off.
Silver sensor
) mark to turn the TV

Viewing the Connection Panel

Rear Panel
1
0
or
Cable Television
Network
or
2
The product colour and shape may vary depending on the model.
N
Whenever you connect an audio or video system to your set, ensure that all elements are switched off.
N
When connecting an external device, match the colour of the connection terminal to the cable.
N
1
POWER IN
Connect the supplied power cord.
2
COMPONENT IN
Audio (AUDIO L/R) and video (Y/P
Component.
3
LAN
Connect a LAN cable to this port to connect to the Network.
4
PC IN(PC) / AUDIO
Connect to the video and audio output jack on your PC.
5
EXT 1, EXT 2
Inputs or outputs for external devices, such as VCR, DVD,
video game device or video disc players.
Input/Output Specification
Connector
EXT 1
EXT 2 Output you can choose.
6
DIGITAL AUDIO OUT (OPTICAL)
Video Audio(L/R) RGB
Connect to a Digital Audio Component.
7
AUDIO OUT(AUDIO R/L)
Connect RCA audio signals from the TV to an external
source, such as Audio equipment.
8
SERVICE
Input Output
5 7 96
B/PR) inputs for
Video + Audio(L/R)
Only TV or DTV output is
available.
9
HDMI IN 1, 2, 3
- No additional Audio connection is needed for an HDMI to HDMI connection.
- When using an HDMI/DVI cable connection, you must use the HDMI IN 2 jack.
What is HDMI?
N
High Definition Multimedia interface allows the
­transmission of high definition digital video data and multiple channels of digital audio.
- The HDMI/DVI terminal supports DVI connection to an extended device with the appropriate cable (not supplied). The difference between HDMI and DVI is that the HDMI device is smaller in size, has the HDCP (High Bandwidth Digital Copy Protection) coding feature
installed, and supports multi - channel digital audio.
DVI IN(HDMI2) AUDIO L/R
DVI audio outputs for external devices.
0
ANT IN
75Ω Coaxial connector for Aerial/Cable Network.
Supported modes for HDMI/DVI and Component
HDMI/DVI 50Hz X X X O O O O HDMI/DVI 60Hz X O X X O O O
Component O O O O O O O
83 4
480i 480p 576i 576p 720p 1080i 1080p
Connector for service.
or
English - 6
English - 7
Side Panel
4
1
2
3
4
The product colour and shape may vary depending on the model.
N
1
COMMON INTERFACE Slot
Insert CI (Common Interface) card into the slot. (refer to page 26)
− When not inserting
Signal is displayed on the screen.
− The pairing information containing a telephone number, CI CARD ID, Host ID, and other information will be displayed in about 2~3 minutes. If an error message is displayed,
please contact your service provider.
− When the channel information configuration has finished,
the message Updating Completed is displayed, indicating that the channel list is now updated.
Insert the CI-Card in the direction marked on it.
N
2
HDMI IN 4
Connect to the HDMI jack of a device with HDMI output.
3
WISELINK PRO
Connect a USB mass storage device to view and play photo
files (JPEG), audio files (MP3) and movie files. You can connect to SAMSUNG’s network wirelessly.
4
S-VIDEO or VIDEO / AUDIO L/R
Video (S-Video or Video) and audio inputs for external
devices, such as a camcorder or VCR.
CI CARD in some channels, Scramble
or
5
5
HEADPHONES JACK
You can connect a set of headphones if you wish to
watch a television programme without disturbing the
other people in the room.
Prolonged use of headphones at a high volume may
N
damage your hearing.

Remote Control

You can use the remote control up to a distance of about 23 feet from the TV.
The performance of the remote control may be affected by bright light.
N
1
POWER button
(turns the TV on and off)
2
Selects the TV mode directly.
3
Number buttons for direct channel
access
4
One or more digit channel selection
5
Temporary sound switch-off
6
Available source selection
7
Volume increase
Volume decrease
8
Electronic Program Guide (EPG)
display
9
Use to quickly select frequently used
functions.
0
Control the cursor in the menu
!
Use to see information on the
current broadcast
@
Use these buttons in the Channel
list and WISELINK, etc.
$
Press to select the optional display
and sound modes for sports, cinema and games.
%
Use these buttons in the Channel
list, WISELINK Pro and Anynet+.
^
ON/OFF
Press to backlight the buttons on the
remote. This function is convenient for using at night or when the room
is dark. (Using the remote control with the ON/OFF( ) light button set to On will reduce the battery usage time.)
&
Previous channel
*
Next channel
Previous channel
(
Displays the main on-screen menu
)
This function enables you to view
and play photo (JPEG) , audio files (MP3) and movie files from an external device.
a
Returns to the previous menu
b
Exit the on-screen menu
c
Press to use the News, Stock
Market and Weather Forecast information services available over the network.
d Use this when connecting a
SAMSUNG DMA (Digital Media
Adapter) device through an HDMI
interface and switching to DMA mode.
(The DMA button is optional.) For
more information on the operating procedures, refer to the user manual
of the DMA. This button is available
when Anynet+(HDMI-CEC) is On
(see page 55)
e
This function enables you to view
Content Library.
f
Digital subtitle display
Teletext Functions
2
Exit from the teletext display
(depending on the model)
6
Teletext mode selection (LIST/
FLOF)
8
Teletext store
9
Teletext size
!
Teletext reveal
@
Fastext topic selection
#
Teletext display/mix both teletext
information and the normal
broadcast
&
Teletext sub page
*
P :Teletext next page
P :Teletext previous page
(
Teletext index
a
Teletext hold
b
Teletext cancel
English - 8
English - 9

Installing Batteries in the Remote Control

1.
Lift the cover at the back of the remote control upward as shown in the gure.
2.
Install two AAA size batteries.
Make sure to match the ‘+’ and ‘–’ ends of the batteries with the diagram
N
inside the compartment.
3.
Close the cover.
Remove the batteries and store them in a cool, dry place if you won’t be
N
using the remote control for a long time. Using the remote control with the ON / OFF @ light button set to on will
N
reduce the battery usage time.
If the remote control doesn’t work, check the following:
N
1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power outage or is the power cord unplugged?
5. Is there a special uorescent light or neon sign nearby?

Switching On and Off

The mains lead is attached to the rear of your set.
1.
Plug the mains lead into an appropriate socket.
The standby indicator lights up on your set.
N
2.
Press the POWERP button on your set.
You also can press the POWERP button or the TV button on the remote control to turn the TV on.
N
The programme that you were watching last is reselected automatically.
N
3.
Press the numeric button (0~9) or channel up / down (< / >) button on the remote control or >C/P.P< button on your
set.
When you switch the set on for the very rst time, you will be asked to choose language in which the menus are to be
N
displayed.
4.
To switch your set off, press the POWERP button again.

Placing Your Television in Standby Mode

Your set can be placed in standby mode in order to reduce the power consumption. The standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).
Press the POWERP button on the remote control.
1.
The screen is turned off and a red standby indicator appears on your set.
N
2.
To switch your set back on, simply press the POWERP, numeric buttons (0~9), TV button or channel up / down (< / >) button again.
Do not leave your set in standby mode for long periods of time (when you are away on holiday, for example). It is best to
N
unplug the set from the mains and aerial.

Viewing the Menus

1. With the power on, press the MENU button. The main menu appears on the
screen. The menu’s left side has icons: Picture, Sound, Channel, Setup, Input,
Application.
2.
Press the ▲ or ▼ button to select one of the icons. Then press the ENTERE button to access the icon’s sub-menu.
3.
Press the EXIT button to exit.
The on-screen menus disappear from the screen after about one minute.
N

Using the TOOLS Button

You can use the TOOLS button to select your frequently used functions quickly and easily. The Tools menu changes depending on which external input mode you are viewing.
1.
Press the TOOLS button. The Tools menu will appear.
2.
Press the ▲ or ▼ button to select a menu, then press the ENTERE button.
3.
Press the ▲ / ▼ / ◄ / ► / ENTERE buttons to display, change, or use the selected items. For a more detailed description of each function, refer to the
corresponding page.
Anynet+ (HDMI-CEC): see page 54
Picture Size: see page 18
Picture Mode: see page 16
Sound Mode: see page 22
Sleep Timer: see page 27
SRS TS XT: see page 22
Energy Saving: see page 26
Dual l ll: see page 23
PIP: see page 20
Auto Adjustment: see page 20
Picture
Mode
:
Cell Light : 7 Contrast : 95 Brightness : 45 Sharpness : 50 Colour : 50
Tint (G / R) : G50 / R50
Detailed Settings
Tools
Anynet+ (HDMI-CEC) Picture Size : Auto Wide Picture Mode : Standard Sound Mode : Custom Sleep Timer : Off SRS TS XT : Off Energy Saving : Off Dual l ll : Mono
U
Move E Enter e Exit
Standard

Using the Wheel button

To increase the channel number, turn the wheel clockwise when the Channel
Display is displayed. To decrease the channel number, turn the wheel counterclockwise.
To turn the volume up, turn the wheel clockwise when the Volume
Control window is displayed. To turn the volume down, turn the wheel
counterclockwise.
To move to a lower menu, turn the wheel clockwise when the menu Display is
displayed. To move to a higher menu, turn the wheel counterclockwise.
English - 10
English - 11

Plug & Play Feature

When the TV is initially powered on, basic settings proceed automatically and subsequently.
1.
Press the POWER button on the remote control. The message Valitse valikkokieli, myymälädemo, kanavat ja kellonaika. is displayed.
E
2.
Press the ENTER automatically displayed. Press the ENTER
3.
Select the appropriate language by pressing the ▲ or ▼ button. Press the
E
ENTER
4.
Press the ◄ or ► button to select Store Demo or Home Use, then the ENTER
N N N
button to conrm your choice.
We recommend setting the TV to Home Use mode for the best picture in your home environment.
Store Demo mode is only intended for use in retail environments. If the unit is accidentally set to Store Demo mode and you want to return to Home Use (Standard): Press the Volume
button, then Valitse kuvaruutuvalikon kieli. menu is
E
button.
Valitse valikkokieli, myymälädemo, kanavat ja kellonaika.
E
button.
button on the TV. When the volume OSD is displayed, press and hold the MENU button on the TV for 5 seconds. The Screen Saver is activated if there is no remote control key input for longer than 1 minute while Plug & Play is
N
running.
The Screen Saver is activated if there is no operating signal for longer than 15 minutes.
N
5.
Press the ENTERE button. Select the appropriate country by pressing the ▲ or ▼ button. Press the ENTERE button to
conrm your choice.
E
6.
Press the ▲ or ▼ button to select the channel source to memorize. Press the ENTER
Digital & Analogue: Digital and Analogue channels.
N
button to select Start.
Digital: Digital channels. Analogue: Analogue channels.
7.
Press the ▲ or ▼ button to memorize the channels of the selected connection, then press the ENTERE button.
Air: Air antenna signal.
N
Cable: Cable antenna signal.
The channel search will start and end automatically.
N
Press the ENTER
N
After all the available channels are stored, the message Set the Clock Mode. is displayed.
N
8.
Press the ENTERE button. Press the ▲ or ▼ button to select Auto, then Press the ENTERE button.
If you select Manual, Set current date and time is displayed. (See page 27)
N
If you have received a digital signal, the time will be set automatically. If
N
not, see page 27 to set the clock.
9.
The message Enjoy your viewing is displayed. When you have nished, press the ENTER
E
button.
E
button at any time to interrupt the memorization process.
Setup
If you want to reset this feature...
1.
Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER
2.
Press the ENTER
3.
Enter your 4 digit PIN number. The default PIN number of a new TV set is
E
E
button.
button again to select Plug & Play.
‘0-0-0-0’.
If you want to change PIN number, refer to 23 page.
N
The Plug & Play feature is only available in the TV mode.
N
Plug & Play
OK
Plug & Play
Language : English
Time
Network Selection : Cable Wireless Network Setup
Cable Network Setup Child Lock : On
Change PIN
E Hyväksy

Channel Control

Storing Channels and channel

Country
Analogue Channel: You can change the country for analogue channels.
Digital Channel: You can change the country for digital channels.
The PIN number input screen appears. Enter your 4 digit PIN number.
N
Channel
Country
Auto Store Manual Store
Full Guide
Mini Guide
Default Guide : Mini Guide
Channel List
Channel Mode : Added Ch.

Auto Store
You can scan for the frequency ranges available to you (and availability depends on your country). Automatically allocated programme numbers may not correspond to actual or desired programme numbers.
Digital & Analogue: Digital and Analogue channels.
Digital: Digital channels.
Analogue: Analogue channels.
You can memorize the channels of the selected connection.
Air: Air antenna signal.
Cable: Cable antenna signal.
Scans for all channels with active broadcast stations and stores them in the TV’s memory.
N
If you want to stop Auto Store, press the ENTER
N
The Stop Auto Store? message will be displayed.
N
Select Yes by pressing the ◄ or ► button, then press the ENTER
N
If a channel is locked using the Child Lock function, the PIN input window appears.
N
Digital & Analogue / Digital
The update procedures differ depending on the selected Country.
Update the channel list by selecting an appropriate option.
When the Country was set to Finland
Cable: Scans cable channels.
-
Air: Scans aerial channels.
-
This product cannot scan both cable and aerial channels at the sametime.
N
When it has nished, the number of scanned services will be displayed.
N
The existing favourite channel list will not be deleted when the channel list is updated.
N
When the Country was set to Sweden, or Denmark
When selecting Cable:
N
Frequency: Displays the frequency for the channel. (Differs in each country)
-
Modulation: Displays available modulation values.
-
Symbol Rate: Displays available symbol rates.
-
Network ID: Displays the network identication code.
-
Press the red button to start the scan for digital services. When it has nished, channels are updated in the channel list. When selecting Air:
N
Press the ENTERE button to select Start.
E
button.
E
button.
Manual Store
Scans for a channel manually and stores it in the TV’s memory.
N
If a channel is locked using the Child Lock function, the PIN input window appears.
N
Digital Channel
Manual store for digital channels.
When the Country was set to Finland
Press the ▲ or ▼ button to select Cable or Air, then press the ENTERE button.
When selecting Cable:
N
Frequency: Displays the frequency for the channel. (Differs in each country)
-
Modulation: Displays available modulation values.
-
Symbol Rate: Displays available symbol rates.
­Press the ENTERE button to start the scan for digital services.
When it has nished, channels are updated in the channel list. When selecting Air:
N
Channel: Channel “21” to “69” in sequence are displayed (depending on the country)
-
Frequency: The frequency available in the Channel group is displayed.
-
Bandwidth: The available bandwidths are 8 MHz.
­Press the ENTERE button to start the scan for digital services.
When it has nished, channels are updated in the channel list.
English - 12
English - 13
When the Country was set to Sweden, Denmark, or Norway
Channel: Channel “21” to “69” in sequence are displayed (depending on the country)
-
Frequency: The frequency available in the Channel group is displayed.
-
Bandwidth: The available bandwidths are 8 MHz.
-
Press the ENTERE button to start the scan for digital services.
When it has nished, channels are updated in the channel list.
Analogue Channel
Manual store for analogue channel.
Programme (Programme number to be assigned to a channel): Sets the programme number using the ▲, ▼ or number
(0~9) buttons.
ColourSystem→Auto/PAL/SECAM/NTSC4.43
Sound SystemBG / DK / I / L: Sets the sound system value using the ▲ or ▼ button.
Channel (When you know the number of the channel to be stored): Press the ▲ or ▼ button to select C (Air channel) or S
(Cable channel). Press the ► button, then press the ▲, ▼ or number (0~9) buttons to select the required number.
You can also select the channel number directly by pressing the number (0~9) buttons.
N
If there is abnormal sound or no sound, reselect the sound standard required.
N
Search (When you do not know the channel numbers): Press the ▲ or ▼ button to start the search. The tuner scans the
frequency range until the rst channel or the channel that you selected is received on the screen. Store (When you store the channel and associated programme number): Set to OK by pressing the ENTER
Channel mode
N
P (Programme mode): When completing tuning, the broadcasting stations in your area have been assigned to position
-
numbers from P00 to P99. You can select a channel by entering the position number in this mode. C (Air channel mode): You can select a channel by entering the assigned number to each air broadcasting station in
­this mode.
S (Cable channel mode): You can select a channel by entering the assigned number for each cable channel in this
­mode.
Full Guide / Mini Guide
The EPG (Electronic Programme Guide) information is provided by the broadcasters. Programme entries may appear blank or out of date as a result of the information broadcast on a given channel. The display will dynamically update as soon as new information becomes available.
For the detailed procedures on using Full Guide and Mini Guide, refer to
N
the descriptions on page 13. You can also display the guide menu simply by pressing the GUIDE button.
O
(To congure the Default Guide, refer to the descriptions.)
Full Guide:
is displayed which may be scrolled forwards or backwards in time. Mini Guide:
the current programme onwards according to the programme starting time order.
Displays the programme information as time ordered One hour segments. Two hours of programme information
The information of each programme is displayed by each line on the current channel Mini Guide screen from
: Sets the colour system value using the ▲ or ▼ button.
E
button.
Default Guide
Mini Guide / Full Guide:
button on the remote control is pressed.
Channel List
For the detailed procedures on using the Channel List, refer to the descriptions on pages 15~16.
Channel Mode
When the press the P >/< button, Channels will be switched within the selected channel list. Added Ch.: Channels will be switched within the memorized channel list.
Favourite Ch.: Channels will be switched within the favourite channel list.
You can decide whether to display either the Mini Guide or the Full Guide when the GUIDE
Fine Tune
If the reception is clear, you do not have to ne tune the channel, as this is done automatically during the search and store operation. If the signal is weak or distorted, you may have to ne tune the channel manually.
Fine tuned channels that have been saved are marked with an asterisk * on the right-hand side of the channel number in
N
the channel banner.
E
To reset the ne-tuning, select Reset by pressing the ▲ or ▼ button and then press the ENTER
N
Only Analogue TV channels can be ne tuned.
N
Signal Information
button.
You can get information about the signal status.
If the signal status is poor, the Weak or No Signal message is displayed.
N
While viewing a Digital channel, this function can be selected.
N
The technical information for signal status is displayed.
N
- Frequency / Service ID / Multiplex / Network / Bit error level / Signal Strength
Using the Full / Mini Guide
Full Guide
900 f tn 901 ITV Play 902 Kerrang! 903 Kiss 903 oneword 903 Smash Hits!
Watch
DTV Cable 900 f tn 2:10 Tue 1 Jun Freshmen On Campus 2:00 - 2:30
No Detailed Information
Today 2:00 - 3:00 3:00 - 4:00
Freshmen O..
Street Hypn..
Mint Extra
Loaded
Fresh 40 with Dynamite MC
The Distillery Smash Hits! Sunday
Information
No Information
No Information Kisstory No Information
Mini Guide +24 Hours Exit
Select a programme by pressing the ▲/▼/◄/► button.
▲/▼/◄/►,
(ENTER)
If the next progrmme is selected, it is scheduled with the clock icon displayed. If the ENTERE button is pressed again, press the ▲/▼/◄/► button to select Cancel Schedules, the scheduling is canceled with the clock icon gone. For details about scheduling programmes, refer to the section.
RED Toggle between the Mini Guide or Full Guide.
GREEN
YELLOW
Full Guide: Scroll backwards quickly (24 hours). Mini Guide: Display next page quickly.
Full Guide: Scroll forwards quickly (24 hours). Mini Guide: Display previous page quickly.
BLUE Exit the guide.
INFO button for the detailed information. Channel Number, Running Time, Status Bar, Parental Level,
INFO
Video Quality Information (HD/SD), Sound Modes, Subtitle or Teletext, languages of Subtitle or Teletext and brief summary of the highlighted programme are included on the detailed information. “…” will be
appeared if the summary is long.
Mini Guide DTV Cable 900 f tn
2:00 2:30 5:00
Watch
Freshmen On Campus
Street Hypnosis
Booze Britain
Information
Full Guide Next Page Exit
English - 14
English - 15

Managing Channels

Using this menu, you can Add / Delete or set Favourite channels and use the programme guide for digital broadcasts.
Select a channel in the All Channels, Added Channels ,Favourites or
N
Programmed screen by pressing the ▲ / ▼ buttons, and pressing the ENTERE button. Then you can watch the selected channel.
All Channels:
Added Channels:
Favourites:
Programmed:
Shows all currently available channels.
Shows all added channels.
Shows all favourite channels.
Shows all current reserved programmes.
Mini Guide
Default Guide : Mini Guide
Channel
Channel List
Channel Mode : Added Ch. Fine Tune
Signal Information
Using the Colour buttons with the Channel List
N
Red (Channel Type): Toggle between your TV, Radio, Data / Other and All.
-
Green (Zoom): Enlarges or shrinks a channel number.
-
Yellow (Select): Selects multiple channel lists.
-
TOOLS (Option): Displays the Delete (or Add), Add to Favourite (or Delete
-
from Favourite), Lock (or Unlock), Timer Viewing, Edit Channel Name, Sort, Edit Channel Number, Select All, Deselect All or Auto Store menu.
(The Options menus may differ depending on the situation.)
Channel Status Display Icons
N
An Analogue channel.
A
A channel set as a Favourite.
\
A locked channel.
c
A channel selected by pressing the yellow button.
(
A programme currently being broadcast.
)
A reserved programme
824 UKTV Gold
Added Channels
825 UKTV style
A 1 C --
A 2 C A 3 ♥ C A 4 C A 5 C A 6 C A 7 C A 8 C
All
Channel Type Zoom Select
--
--
--
--
--
--
--
Option
Channel List Option Menu (in All Channels / Added Channels / Favourites)
Press the TOOLS button to use the option menu.
N
Option menu items may differ depending on the channel status.
N
Add / Delete
You can delete or add a channel to display the channels you want.
All deleted channels will be shown on All Channels menu.
N
A gray-coloured channel indicates the channel has been deleted.
N
The Add menu only appears for deleted channels.
N
You can also delete a channel in the Added Channels or Favourite menu
N
in the same manner.
Add to Favourite / Delete from Favourite
You can set channels you watch frequently as favourites.
The ♥ symbol will be displayed and the channel will be set as a favourite.
N
All favourite channels will be shown on Favourite menu.
N
Lock / Unlock
You can lock a channel so that the channel cannot be selected and viewed. This function is available only when the Child Lock is set to on. (see page 24)
The PIN number input screen appears. Enter your 4 digit PIN number.
N
The default PIN number of a new TV set is 0-0-0-0. You can change the PIN, by selecting Change PIN from the menu.
N
The \ symbol will be displayed and the channel will be locked.
N
Timer Viewing
If you reserve a programme you want to watch, the channel is automatically switched to the reserved channel in the Channel
List; even when you are watching another channel. To reserve a programme , set the current time rst. (See page 27.)
Only memorized channels can be reserved.
N
You can set the channel, month, day, year, hour and minute directly by pressing the number buttons on the remote
N
control. Reserving a programme will be shown on Programmed menu.
N
Digital Programme Guide and Viewing Reservation
N
When a digital channel is selected, and you press the ► button, the Programme Guide for the channel appears. You can reserve a programme according to the procedures described above.
824 UKTV Gold
All Channels
825 UKTV style
A 1 C --
A 2 C A 3 C A 4 C A 5 C A 6 C A 7 C A 8 C
All
Channel Type Zoom Select
--
--
--
--
--
--
--
Delete
Add to Favourite Lock
Timer Viewing Edit Channel Name Sort
Option
Edit Channel Name (only analogue channel)
Channels can labeled so that their call letters appear whenever the channel is selected.
The names of digital broadcasting channels are automatically assigned and cannot be labeled.
N
Edit Channel Number (only digital channel)
You can also edit the channel number by pressing the number buttons on the remote control.
Sort
This operation allows you to change the programme numbers of the stored channels. This operation may be necessary after
using the auto store.
The function is only available in Analouge.
N
Select All / Deselect All
Select All: You can select all the channels in the channel list.
Deselect All: You can deselect all the selected channels in the channel list.
You can perform the add / delete, add to Favourites / delete from Favourites, or lock / unlock function for multiple
N
channels at the same time. Select the required channels and press the yellow button to set all the selected channels at
the same time. The c mark appears to the left of the selected channels.
N
You can only select Deselect All when there is a selected channel.
N
Auto Store
For further details on setting up options, refer to page 11.
N
If a channel is locked using the Child Lock function, the PIN input window appears.
N
Channel List Option Menu (in Programmed )
You can view, modify or delete a reservation.
Press the TOOLS button to use the option menu.
N
Change Info: Select to change a viewing reservation.
Cancel Schedules: Select to cancel a viewing reservation.
Information: Select to view a viewing reservation. (You can also change
the reservation information.) Select All: Select all reserved programmes.
Programmed
1 / 1 / 2008
13:59 5 TV1 Quincy, M.E
18:59 2 TV3 The Equalizer 20:59 2 TV3 McMillan & Wife 21:59 2 TV3 M.Spillane’s mike Hammer
All
Channel Type Zoom Select
Change Info
Cancel Schedules Information Select All
Option Information

Picture Control

Changing and Resetting the Picture Settings

Mode
You can select the type of picture which best corresponds to your viewing
requirements.
Dynamic: Selects the picture for high-definition in a bright room.
Standard: Selects the picture for the optimum display in a normal
environment.
Movie: Selects the picture for viewing movies in a dark room.
Press the TOOLS button to display Tools menu.
T
You can also set the picture mode by selecting Tools→PictureMode.
Cell Light / Contrast / Brightness / Sharpness / Colour / Tint(G/R)
Your television has several setting options that allow you to control the picture quality.
Cell Light: Adjusts the pixel brightness. 10 is brightest.
Contrast: Adjusts the contrast level of the picture.
Brightness: Adjusts the brightness level of the picture.
Sharpness: Adjusts the edge definition of the picture.
Colour: Adjusts Colour saturation of the picture.
English - 16
Picture
Mode : Standard
Cell Light : 7 Contrast : 95 Brightness : 45 Sharpness : 50 Colour : 50
Tint(G/R) : G50 / R50
Detailed Settings
English - 17
Tint(G/R): Adjusts the Colour tint of the picture.
Select a picture mode to be adjusted rst. The adjusted values are saved for each picture mode.
N
When you make changes to Cell Light, Contrast, Brightness, Sharpness, Colour or Tint(G/R), the OSD will be
N
adjusted accordingly. In Analogue TV, Ext., AV, S-Video modes of the PAL system, you cannot use the Tint Function.
N
In PC mode, you can only make changes to Cell Light, Contrast and Brightness.
N
Settings can be adjusted and stored for each external device you have connected to an input of the TV.
N
The energy consumed during use can be signicantly reduced if the level of brightness of the picture is reduced, and then
N
this will reduce the overall running cost.
Detailed Settings
Samsung’s new TVs allow you to make even more precise picture settings than previous models. See below to adjust detailed picture settings.
Detailed Settings is available in Standard or Movie mode.
N
In PC mode, you can only make changes to Dynamic Contrast, Gamma
N
and White Balance from among the Detailed Settings items.
BlackAdjust→Off/Low/Medium/High
Colour : 50
Tint (G / R) : G50 / R50
Picture
DetailedSettings 
Picture Options
Picture Reset
You can select the black level on the screen to adjust the screen depth.
DynamicContrast→Off/Low/Medium/High
You can adjust the screen contrast so that the optimal contrast is provided.
Gamma
You can adjust the Primary Colour (Red, Green, Blue) Intensity.
Colour Space
Colour Space is a colour matrix composed of red, green and blue colours. Select your favourite Colour Space to experience
the most natural colour.
Auto: Auto Colour Space automatically adjusts to the most natural colour tone based on programme sources.
Native: Native Colour Space offers deep and rich colour tone.
Custom: Adjusts the colour range to suit your preference.
Customizing the Colour Space
N
Colour→Red/Green/Blue/Yellow/Cyan/Magenta
­Adjusts the Colour range to suit your preference. Colour is available when Colour Space is set to Custom.
-
Red / Green / Blue: In Colour, you can adjust the RGB values for the selected colour.
-
Reset: Resets the colour space to the default values.
-
White Balance
You can adjust the colour temperature for more natural picture colours.
R-Offset / G-Offset / B-Offset / R-Gain / G-Gain / B-Gain: Changing the adjustment value will refresh the adjusted screen.
Reset: The previously adjusted white balance will be reset to the factory defaults.
Flesh Tone
You can emphasize the pink Flesh Tone in the picture.
Changing the adjustment value will refresh the adjusted screen.
N
EdgeEnhancement→Off/On
You can emphasize object boundaries in the picture.
xvYCC→Off/On
Setting the xvYCC mode to on increases detail and colour space when watching movies from an external device (i.e. DVD player).
xvYCC is available when the picture mode is set to Movie, and the external input is set to HDMI or Component mode.
N
If xvYCC function is active, PIP cannot be selected.
N
Picture Options
In PC mode, you can only make changes to the Colour Tone, Size and
N
Screen Burn Protection from among the items in Picture Options.
Colour Tone→Cool2 / Cool1 / Normal / Warm1 / Warm2
You can select the most comfortable colour tone to your eyes.
The adjusted values are stored according to the selected Picture mode.
N
Warm1 or Warm2 is only activated when the picture mode is Movie.
N
Tint (G / R) : G50 / R50
Detailed Settings
Picture
PictureOptions
Picture Reset
Size
You can select the picture size which best corresponds to your viewing requirements.
Press the TOOLS button to display Tools menu.
T
You can also set the size by selecting Tools→PictureSize.
Auto Wide: Automatically adjusts the picture size to the 16:9 aspect ratio.
16:9
: Adjusts the picture size to 16:9 appropriate for DVDs or wide broadcasting.
Wide Zoom: Magnify the size of the picture more than 4:3.
Zoom: Magnies the 16:9 wide picture (in the vertical direction) to t the screen size.
4:3: This is the default setting for a video movie or normal broadcasting.
Just Scan: Use the function to see the full image without any cutoff when HDMI (720p / 1080i / 1080p)
or Component (1080i / 1080p) signals are input.
Depending on the input source, the picture size options may vary.
N
The items available may differ depending on the selected mode.
N
In PC Mode, only 16:9 and 4:3 mode can be adjusted.
N
Settings can be adjusted and stored for each external device you have connected to an input of the TV.
N
Temporary image retention may occur when viewing a static image on the set for more than two hours.
N
E
Wide Zoom: Press the ► button to select Position, then press the ENTER
N
move the screen up / down. Then press the ENTER Zoom: Press the ► button to select Position, then press the ENTER
N
picture up and down. Then press the ENTER
E
button.
E
button. Press the ► button to select Size, then press the ENTER
button. Press the ▲ or ▼ button to
E
button. Press the ▲ or ▼ button to move the
E
button. Press the ▲ or ▼ button to magnify or reduce the picture size in the vertical direction. Then press the
E
ENTER After selecting Just Scan in HDMI (1080i / 1080p) or Component (1080i / 1080p) mode: Select Position by pressing
N
button.
the ◄ or ►button. Use the ▲, ▼, ◄ or ► button to move the picture.
E
Reset: Press the ◄ or ► button to select Reset, then press the ENTER
N
If you use the Just Scan function with HDMI 720p input, 1 line will be cut at the top, bottom, left and right as in the
N
button. You can initialize the setting.
overscan function. When Double ( , ) mode has been set in PIP, the Picture Size cannot be set.
N
Screen Mode→16:9 / Wide Zoom / Zoom / 4:3
When setting the picture size to Auto Wide in a 16:9 wide TV, you can determine the picture size you want to see the 4:3 WSS (Wide Screen Service) image or nothing. Each individual European country requires different picture size so this function
is intended for users to select it.
16:9
: Sets the picture to 16:9 wide mode.
Wide Zoom: Magnify the size of the picture more than 4:3.
Zoom: Magnify the size of the picture vertically on screen.
4:3: Sets the picture to 4:3 normal mode.
This function is available in Auto Wide mode.
N
This function is not available in PC, Component or HDMI mode.
N
Digital NR→Off / Low / Medium / High / Auto
If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction feature to help reduce any
static and ghosting that may appear on the screen.
When the signal is weak, select one of the other options until the best picture is displayed.
N
DNIe→Off / Demo / On
This TV includes the DNIe function so as to provide a high visual quality. If you set DNIe to on, you can view the screen with the DNIe feature activated. If you set the DNIe to Demo, you can view the applied DNIe and normal pictures on the screen, for demonstration purposes. Using this function, you can view the difference in the visual quality.
DNIe™ (Digital Natural Image engine)
N
DNIe™
This feature brings you more detailed image with 3D noise reduction, detail enhancement, contrast enhancement and white enhancement. New image compensation Algorithm gives brighter, clearer, more detailed image to you. DNIe™ technology will t every signal into your eyes.
This function is not available in Movie and Standard mode.
N
HDMI Black Level→Normal / Low
You can directly select the black level on the screen to adjust the screen depth.
This function is active only when the external input connects to HDMI (RGB signals).
N
English - 18
English - 19
Real100HzDemo→Off/On
You can get a clear distinction between Real 100Hz and 50Hz, especially when watching fast moving scenes. Therefore, when seeing slow moving scenes, you will not be able to distinguish between Real 100Hz and 50Hz. Demo 100Hz works only with 50Hz signal. Real 100Hz demo mode is provided for shop demonstration with special pictures.
Movie Plus→Off / Low / Medium / High / Demo
You can view more natural skin and clear text even in fast moving scenes.
Use this function when watching movies.
N
This function is not available in Wide Zoom and Zoom modes.
N
This function is not available when PIP is set to On.
N
It is not supported in HDMI 1080p/24Hz, 25Hz, 30Hz mode.
N
Blue Only Mode→Off / On
This function is for AV device measurement experts. This function displays the blue signal only by removing the red and green signals from the video signal so as to provide a Blue Filter effect that is used to adjust the Colour and Tint of video equipment such as DVD players, Home Theaters, etc. Using this function, you can adjust the Colour and Tint to preferred values appropriate to the signal level of each video device using the Red / Green / Blue / Cyan / Magenta / Yellow Colour Bar Patterns, without using an additional Blue Filter.
Blue Only Mode is available when the picture mode is set to Movie or Standard.
N
Screen Burn Protection
To reduce the possibility of screen burn, this unit is equipped with screen burn prevention technology. This technology enables you to set picture movement up/down (Vertical Line) and side to side (Horizontal Dot). The Time setting allows you to program the time between movement of the picture in minutes.
Pixel Shift: Using this function, you can minutely move pixels on the PDP in horizontal or vertical direction to minimize after
• image on the screen.
Set Pixel Shift to On by pressing the ▲ or ▼ button, then press the ENTERE button.
N
Select the required option by pressing the ▲ or ▼ button, then press the ENTERE button.
N
Available options: Horizontal Dot, Vertical Line, Time.
N
Optimum condition for pixel shift;
N
PC TV/Ext/AV/Component/HDMI
Horizontal Dot 4 4
Vertical Line 4 4
Time (minute) 4 2 min
The Pixel Shift value may differ depending on the monitor size (inches) and mode.
N
This function is not available in the Just Scan mode.
N
All White: This function helps remove after images on the screen by changing the colour of pixels to white. Use this
function when there are remaining after images or symbols on the screen especially when you displayed a still image on the
screen for a long time.
Scrolling: This function helps remove after images on the screen by moving all the pixels on the PDP according to a
pattern Use this function when there are remaining after images or symbols on the screen especially when you displayed a
still image on the screen for a long time.
Side Gray: When you watch TV with the screen ratio of 4:3, the screen is prevented from any damage by adjusting the
white balance on both extreme left and right sides.
Dark: When you set the screen ratio to 4:3, it darkens the left and right sides.
-
Light: When you set the screen ratio to 4:3, it brightens the left and right sides.
-
PictureReset→ResetPictureMode/Cancel
Resets all picture settings to the default values.
Select a picture mode to be reset. The reset is performed for each picture mode.
N

Viewing Picture-in-Picture

You can display a sub picture within the main picture of set programme or video
input. In this way, you can watch the picture of set programme or video input from any connected equipment while watching the main picture.
You may notice that the picture in the PIP window becomes slightly unnatural
N
when you use the main screen to view a game or karaoke. Press the TOOLS button to display Tools menu.
T
You can also congure PIP related settings by selecting Tools→PIP.
PIP→Off / On
You can activate or deactivate the PIP function.
Main picture Sub picture
Component HDMI 1, HDMI2/DVI, HDMI 3,
HDMI 4 PC
Source
You can select a source of the sub-picture. Size → / /
You can select a size of the sub-picture.
If main picture is in HDMI mode, Size is available.
N
Position → / / /
You can select a position of the sub-picture.
In Double ( , ) mode, Position cannot be selected.
N
Channel
You can select a channel of the sub-picture only when the Source is set to TV.
Press the TOOLS button to display Tools menu.
T
You can also set the picture mode by selecting Tools→PIP
TV, Ext.1, Ext.2, AV
Entertainment : Off Energy Saving : Off
Setup
PIP
Software Upgrade
Common Interface
PIP
PIP : On Source : TV Size : Position : Channel : ATV 11
L
Move E Enter R Return

Setting up the TV with your PC

Preset: Press the SOURCE button to select PC mode.
N
Auto Adjustment
Auto Adjustment allows the PC screen of set to self-adjust to the incoming PC video signal. The values of ne, coarse and position are adjusted automatically.
This function does not work in DVI-HDMI mode.
N
Press the TOOLS button to display Tools menu.
T
You can also set the Auto Adjustment by selecting Tools→Auto
Adjustment.
Screen
Coarse / Fine:
The purpose of picture quality adjustment is to remove or reduce picture noise. If the noise is not removed by Fine-tuning alone, then adjust the frequency as best as possible (Coarse) and Fine-tune again. After the noise has been reduced, readjust the picture so that it is aligned on the center of screen.
PC Position:
Adjust the PC’s screen positioning if it does not t the TV screen.
Press the ▲ or ▼ button to adjusting the
Vertical-Position. Press the ◄ or ► button to adjust the Horizontal-Position. Image Reset:
You can replace all image settings with the factory default values.
English - 20
Picture
Brightness : 45
Sharpness : 50
Auto Adjustment
Screen Detailed Settings
Picture Options
Picture Reset
English - 21

PC Display

Setting Up Your PC Software (Based on Windows XP)
The Windows display-settings for a typical computer are shown below. The actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card. However, even if your actual screens look different, the same basic set-up information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
1.
First, click on ‘Control Panel’ on the Windows start menu.
2.
When the control panel window appears, click on ‘Appearance and Themes’ and a display dialog-box will appear.
3.
When the control panel window appears, click on ‘Display’ and a display dialog­box will appear.
4.
Navigate to the ‘Settings’ tab on the display dialog-box. The correct size setting (resolution)
Optimum: 1920 X 1080 pixels If a vertical-frequency option exists on your display settings dialog box, the
correct value is ‘60’ or ‘60 Hz’. Otherwise, just click ‘OK’ and exit the dialog box.
Display Modes
Both screen position and size will vary depending on the type of PC monitor and its resolution. The resolutions in the table are recommended.
D-Sub Input
Mode Resolution
IBM
VESA
CVT 1920 x 1080RB 66.587 59.934 138.500 + / -
640 x 350 720 x 400 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600
800 x 600 1024 x 768 1024 x 768 1024 x 768
1280 x 1024 1280 x 1024
1360 x 768
1600 x 1200
Horizontal
Frequency (kHz)
31.469
31.469
31.469
37.861
37.500
37.879
48.077
46.875
48.363
56.476
60.023
63.981
79.976
47.712
75.000
Vertical Frequency
(Hz)
70.086
70.087
59.940
72.809
75.000
60.317
72.188
75.000
60.004
70.069
75.029
60.020
75.025
60.015
60.000
Frequency (MHz)
Pixel Clock
25.175
28.322
25.175
31.500
31.500
40.000
50.000
49.500
65.000
75.000
78.750
108.000
135.000
85.500
162.000
Sync Polarity
(H / V)
+ / -
- / +
- / -
- / -
- / ­+ / + + / + + / +
- / -
- / ­+ / + + / + + / + + / + + / +
HDMI / DVI Input
Mode Resolution
640 x 480 800 x 600
VESA
CEA 1920 x 1080p 67.500 60.000 148.500 + / +
When using an HDMI / DVI cable connection, you must use the HDMI IN 2 jack.
N
The interlace mode is not supported.
N
The set might operate abnormally if a non-standard video format is selected.
N
Separate and Composite modes are supported. SOG is not supported.
N
Too long or low quality VGA cable can cause picture noise at high resolution modes (1920x1080).
N
1024 x 768
1280 x 1024
1360 x 768
1600 x 1200
Horizontal
Frequency (kHz)
31.469
37.879
48.363
63.981
47.712
75.000
Vertical Frequency
(Hz)
59.940
60.317
60.004
60.020
60.015
60.000
Pixel Clock
Frequency (MHz)
25.175
40.000
65.000
108.000
85.500
162.000
Sync Polarity
(H / V)
- / ­+ / +
- / ­+ / + + / + + / +

Sound Control

Changing the Sound Standard

Mode→Standard/Music/Movie/Speech/Custom
You can select the type of special sound effect to be used when watching a given broadcast.
Press the TOOLS button to display Tools menu.
T
You can also congure the sound mode by selecting Tools→Sound
Mode.
Equalizer
The sound settings can be adjusted to suit your personal preferences. Mode: You can select a sound mode to suit your personal preferences.
Balance: Controls the balance between the right and left speakers.
100Hz / 300Hz / 1kHz / 3kHz / 10kHz (Bandwidth Adjustment): To adjust the level of different bandwidth frequencies
Reset: Resets the equalizer settings to the default values.
SRSTruSurroundXT→Off/On
TruSurround XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers. TruSurround delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal television speakers. It is fully compatible with all multichannel formats.
Press the TOOLS button to display Tools menu.
T
You can also set the SRS TruSurround XT by selecting Tools→SRSTSXT.
TruSurround XT, SRS and Symbol are trademarks of SRS Labs, Inc. TruSurround XT
technology is incorporated under license from SRS Labs, Inc.
Sound
Mode : Custom
Equalizer SRS TruSurround XT : Off
Audio Language : ---­Audio Format : ----
Audio Description
Auto Volume : Off Select Speaker : TV Speaker
Audio Language
You can change the default value for audio languages. Displays the language information for the incoming stream.
While viewing a digital channel, this function can be selected.
N
You can only select the language among the actual languages being broadcast.
N
AudioFormat→MPEG/DolbyDigital
When sound is emitted from both the main speaker and the audio receiver, a sound echo may occur due to the decoding speed difference between the main speaker and the audio receiver. In this case, use the TV Speaker function.
While viewing a digital channel, this function can be selected.
N
You can only select the language among the actual languages being broadcast.
N
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
Audio Description
This is an auxiliary audio function that provides an additional audio track for visually challenged persons. This function handles the Audio Stream for the AD (Audio Description), when it is sent along with the Main audio from the broadcaster. Users can turn the Audio Description On or Off and control the volume.
AudioDescription→Off/On: Turn the audio description function on or off.
Volume: You can adjust the audio description volume.
Volume is active when Audio Description is set to On.
N
While viewing a Digital channel, this function can be selected.
N
English - 22
English - 23
Auto Volume→Off/On
Each broadcasting station has its own signal conditions, and so it is not easy to adjust the volume every time the channel is changed. This feature lets you automatically adjust the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when
the modulation signal is low.
SelectSpeaker→ExternalSpeaker/TVSpeaker
If you want to hear the sound through separate speakers, cancel the internal amplier.
The – +, MUTE buttons do not operate when the TV Speaker is set to Off.
N
If you select External Speaker in the Select Speaker menu, the sound settings will be limited.
N
TV's Internal Speakers Audio Out (Optical, L / R Out) to Sound System
TV / Ext. / AV / S-Video / Component / PC / HDMI TV / Ext. / AV / S-Video / Component / PC / HDMI
TV Speaker Speaker Output Sound Output
External Speaker Mute Sound Output
Video No Signal Mute Mute
Sound Select
When the PIP feature is activated, you can listen to the sound of the sub (PIP) picture. Main: Used to listen to the sound of the main picture.
Sub: Used to listen to the sound of the sub picture.
Press the TOOLS button to display Tools menu.
T
You can also set the sound of the sub picture by selecting Tools→PIP→SoundSelect.
Sound Reset
Reset All / Reset Sound Mode / Cancel:
You can restore the Sound settings to the factory defaults.
Select Speaker : TV Speaker
Sound Select : Main
Sound
SoundReset

Selecting the Sound Mode

You can set the sound mode in the Tools menu. When you set to Dual l ll, the current sound mode is displayed on the screen.
Type of broadcast
Regular broadcast
(Standard audio)
Regular + NICAM Mono
NICAM Stereo
A2
Stereo
If the stereo signal is weak and an automatic switching occurs, then switch to the mono.
N
This function is only activated in stereo sound signal. It is deactivated in mono sound signal.
N
This function is only available in TV mode.
N
NICAM-Stereo
NICAM Dual-I/II
Regular broadcast
(Standard audio)
Bilingual or DUAL-I/II
Stereo Stereo
On-screen indication
Mono (Normal use)
NICAM
NICAM Stereo
NICAM Dual-1
Mono (Normal use)
Dual I Dual II
NICAM
Dual-2
(Forced mono)
Mono
(Normal)
Mono
(Normal)
Mono
(Normal)
Mono
Tools
Anynet+ (HDMI-CEC) Picture Size : Auto Wide Picture Mode : Standard Sound Mode : Custom Sleep Timer : Off SRS TS XT : Off Energy Saving : Off Dual l ll Mono ►
U
Move L Adjust e Exit

Function Description

ConguringtheSetupMenu
Language
You can set the menu language.
ChildLock→Off/On
This feature allows you to prevent unauthorized users, such as children, from watching unsuitable programmes by muting out video and audio.
N
Before the setup screen appears, the PIN number input screen appears. Enter your 4 digit PIN number.
N
The default PIN number of a new TV set is 0-0-0-0. You can change the PIN by selecting Change PIN from the menu.
N
You can lock some channels in Channel List. (refer to page 16)
N
Child Lock is available only in TV mode.
Change PIN
You can change your personal ID number that is required to set up the TV.
N
Before the setup screen appears, the PIN number input screen appears. Enter your 4 digit PIN number.
N
The default PIN number of a new TV set is 0-0-0-0.
N
If you forget the PIN code, press the remote control buttons in the following sequence, which resets the PIN to 0-0-0-0: POWER (Off), MUTE, 8, 2, 4, POWER (On).
ParentalLock→ParentalRating
This feature allows you to prevent unauthorized users, such as children, from watching unsuitable programmes by a 4-digit PIN (Personal Identication Number) code that is dened by the user.
-
In the Parental Rating screen, congure the parental ratings.
N
Before the setup screen appears, the PIN number input screen appears. Enter your 4 digit PIN number.
N
The default PIN number of a new TV set is 0-0-0-0. You can change the PIN by selecting Change PIN from the menu.
N
When the parental ratings are set, the \ symbol is displayed.
N
Allow All: Press to unlock all TV ratings. Block All: Press to lock all TV ratings.
Plug & Play
Setup
Language : English
Time
Network Selection : Cable Wireless Network Setup
Cable Network Setup Child Lock : On
Change PIN
Parental Lock
Subtitle
You can activate and deactivate the subtitles. Use this menu to set the Subtitle Mode. Normal under the menu is the basic subtitle and Hard of hearing is the subtitle for a hearing-impaired person.
Subtitle→Off/On: Switches subtitles off or on. Mode→Normal/Hardofhearing
Subtitle Language: Set the subtitle language.
N
If the programme you are watching does not support the Hard of hearing function, Normal automatically activates even though Hard of hearing mode is selected.
N
English is the default in cases where the selected language is unavailable in the broadcast.
N
You can select these options simply by pressing the SUBT. button on the remote control.
Teletext Language
You can set the Teletext language by selecting the language type.
N
English is the default in cases where the selected language is unavailable in the broadcast.
: Sets the subtitle mode.
English - 24
English - 25
Preference
Primary Audio Language / Secondary Audio Language / Primary Subtitle Language / Secondary Subtitle Language /
Primary Teletext Language / Secondary Teletext Language
Using this feature, users can select one of the languages. The language selected here is the default when the user selects a channel.
If you change the language setting, the Subtitle Language, Audio Language, and the Teletext Language of the Language
menu are automatically changed to the selected language.
The Subtitle Language, Audio Language, and the Teletext Language of the Language menu show a list of languages supported by the current channel and the selection is highlighted. If you change this language setting, the new selection is only valid for the current channel. The changed setting does not change the setting of the Primary Subtitle Language, Primary Audio Language, or the Primary Teletext Language of the Preference menu.
LightEffect→Off/InStandby/WatchingTV/Always
You can turn on/off the blue LED on the front of TV according to the situation. Use it for saving power or when the LED dazzles
your eyes.
Off: The blue LED is always off.
In Standby: The blue LED lights while in Standby mode and it turns off when your TV is turned on.
Watching TV: The blue LED lights when watching TV and it turns off when your TV is turned off.
Always: The blue LED always lights.
Set the Light Effect to Off to reduce the power consumption.
N
Melody
Off / Low / Medium / High
The TV power on / off melody sound can be adjusted.
The Melody does not play
N
When no sound is output from the TV because the MUTE button has been pressed.
­When no sound is output from the TV because the (Volume) button has been pressed.
­When the TV is turned off by Sleep Timer function.
-
Entertainment
The Entertainment mode enables you to select the optimal display and sound for sports, cinema and games. Off: Switches the Entertainment function off.
Sports: Provides the optimal picture and sound quality for sports.
Cinema: Provides the optimal picture and sound quality for movie watching. You can experience a richer picture and
enhanced sound.
Game: Provides the optimal picture and sound quality for games. This mode accelerates the playing speed when
using an external game console connected to the TV. If you set any of the three Entertainment modes to On, the settings will be locked and can not be adjusted. In addition,
N
Picture and Sound mode settings are not allowed. If you want to make Picture and Sound mode adjustments, the Entertainment mode must be turned off.
The Entertainment settings are saved for each input source.
N
The Entertainment mode is not available at PC source
N
You can press the E.MODE button on the remote control repeatedly to change
O
the Entertainment setting.
Energy Saving
4
This feature adjusts the brightness of the TV in order to reduce power consumption. When watching TV at night, set the
Energy Saving mode option to High to reduce eye fatigue as well as power consumption. Off: Turns off the energy saving function.
Low: Sets the TV to low energy saving mode.
Medium: Sets the TV to medium energy saving mode.
High: Sets the TV to high energy saving mode.
Press the TOOLS button to display Tools menu.
T
You can also set the Energy Saving option by selecting Tools→EnergySaving.
Software Upgrade
To keep your product up-to-date with new Digital Television features then
TV Side Panel
software upgrades are periodically broadcast as part of the normal Television
signal. It will automatically detect these signals and display the software
upgrade banner. You are given the option to install the upgrade.
By USB
USB Drive
Insert a USB drive containing the rmware upgrade into TV. Please be careful to not disconnect the power or remove the USB drive while upgrades are being
applied. The TV will turn off and turn on automatically after completing the
rmware upgrade. Please check the rmware version after the upgrades are complete. When software is upgraded, video and audio settings you have made will return to their default (factory) settings. We recommend you write down your settings so that
you can easily reset them after the upgrade.
By Channel
Upgrades the software using the broadcasting signal.
Standby Mode Upgrade
To continue software upgrade with master power on, Select On by pressing the ▲ or ▼ button. 45 minutes after entering standby mode, a manual upgrade is automatically conducted. Since the power of the unit is turned on internally, the screen may be on slightly for the product. This phenomenon may continue for more than 1 hour until the software upgrade is
completed.
Alternative Software
To display the software version information.
Common Interface
Installing the CI Card
a. Purchase the CI CAM module by visiting your nearest dealer or by phone. b. Insert the CI CARD into the CAM in the direction of the arrow until it ts.
c. Insert the CAM with the CI CARD installed into the common interface slot.
Insert the CAM in the direction of the arrow, right up to the end so that it is
N
parallel with the slot.
d. Check if you can see a picture on a scrambled signal channel.
CI Menu
This enables the user to select from the CAM-provided menu. Select the CI Menu based on the menu PC Card.
Application Info.
This contains information on CAM inserted in the CI slot and displays it.
The Application Info inserting is about the CI CARD. You can install the CAM anytime whether the TV is ON or OFF.
1. Purchase the CI CAM module by visiting your nearest dealer or by phone.
2. Insert the CI CARD into the CAM in the direction of the arrow until it ts.
3. Insert the CAM with the CI CARD installed into the common interface slot. (Insert the CAM in the direction of the arrow, right
up to the end so that it is parallel with the slot.)
4. Check if you can see a picture on a scrambled signal channel.
English - 26
English - 27

Setting the Time

Clock
Setting the clock is necessary in order to use the various timer features of the
TV.
The current time will appear every time you press the INFO button.
N
If you disconnect the power cord, you have to set the clock again.
N
Clock Mode
You can set up the current time manually or automatically.
Auto: Set the current time automatically using the time from the digital
broadcast. Manual: Set the current time to a manually specied time.
Clock Set
You can set the current time manually.
Set up this item when you have set Clock Mode to Manual.
N
You can set the day, month, year, hour, minute directly by pressing the
N
number buttons on the remote control.
SleepTimer→Off/30min/60min/90min/120min/150min
/ 180 min
The sleep timer automatically shuts off the TV after a preset time (30, 60, 90, 120, 150 and 180 minutes).
The TV automatically switches to standby mode when the timer reaches 0.
N
To cancel the Sleep Timer function, select Off.
N
Press the TOOLS button to display Tools menu.
T
You can also set the sleep timer by selecting Tools→SleepTimer.
Plug & Play
Language : English
Setup
Time
Network Selection : Cable Wireless Network Setup
Cable Network Setup Child Lock : On
Change PIN
Parental Lock Subtitle
Time
Clock : -- : -- Sleep Timer : Off
Timer 1 : Inactivated Timer 2 : Inactivated Timer 3 : Inactivated
U
Move E Enter R Return
Timer 1 / Timer 2 / Timer 3
Three different on / off timer settings can be made.
On Time:
Set the hour, minute, and Activate / Inactivate.
(To activate timer with the setting you’ve chosen, set to Activate.)
Off Time:
Set the hour, minute, and Activate / Inactivate.
(To activate timer with the setting you’ve chosen, set to Activate.)
Volume:
Contents:
Set the required volume level.
When the On Timer is active, you can turn on a specic channel or play back contents such as photo or audio
les.
TV / USB: Select TV or USB. (Make sure that an USB device is connected to your TV.)
Antenna: Select ATV or DTV.
Channel: Select the desired channel.
Music: Select the folder containing MP3 les on the USB device.
Photo: Select the folder containing JPEG les on the USB device.
Repeat:
Select Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun, or Manual.
When Manual is selected, press the ► button to select the desired day of the week. Press the ENTER
N
E
button over the
desired day and the c mark will appear. You must set the clock rst.
N
You can set the hour, minute and channel by pressing the number buttons on the remote control.
N
Auto Power Off
N
When you set the timer On, the television will eventually turn off, if no controls are operated for 3 hours after the TV was turned on by the timer. This function is only available in timer On mode and prevents overheating, which may occur if a TV is
on for too long time.

Network Connection

Network Connection - Cable
Cable Connection for a DHCP Environment
The procedures to set up the network using Dynamic Host Conguration Protocol (DHCP) are described below. Since an IP address, subnet mask, gateway, and DNS are automatically allocated when DHCP is selected, you do not have to enter them
manually.
TV Rear Panel
The Modem Port
on the Wall
1. Connect the [LAN] port on the rear panel of the TV and the external modem with a LAN Cable.
2.
Connect the LAN port on the wall and the external modem with a Modem Cable.
You can connect the LAN via a Sharer (Router).
External Modem
(ADSL/VDSL/Cable TV)
Modem Cable
2
IP Sharer
LAN Cable
1
The Modem Port
on the Wall
You can connect the LAN port and the TV directly depending on your network status.
The LAN Port
on the Wall
The terminals (the position of the port and the type) of the external device may differ depending on the manufacturer.
N
If the IP address allocation by the DHCP server has failed, turn the external modem off, turn it on again after at least 10
N
External Modem
(ADSL/VDSL/
Cable TV)
Modem Cable
LAN Cable
LAN Cable
LAN Cable
TV Rear Panel
TV Rear Panel
seconds and then try again.
For the connections between the external modem and the Sharer (Router), refer to the owner’s manual of the corresponding
N
product.
You can connect the TV to the LAN directly without connecting it through a Sharer (Router).
N
You cannot use a manual-connection-type ADSL modem becaus;e it does not support DHCP. You have to use an automatic-
N
connection-type ADSL modem.
English - 28
English - 29
LAN Connection for Static IP Environment
The procedures to set up the network using a static IP address are described below. You have to manually enter the IP address, subnet mask, gateway, and DNS that are provided by your Internet Service Provider (ISP).
TV Rear Panel
The LAN Port
on the Wall
LAN Cable
1
1. Connect the [LAN] port on the rear panel of the TV and the LAN port on the wall using the LAN cable.
You can connect the LAN via a Sharer (Router).
The LAN Port
on the Wall
LAN Cable
The terminals (the position of the port and the type) of the external device may differ depending on the manufacturer.
N
If you are using a static IP address, your ISP will inform you of the IP address, subnet mask, gateway, and DNS. You must
N
IP Sharer
LAN Cable
TV Rear Panel
enter these values to complete the network settings. If you do not know the values, ask your network administrator. For the information on how to congure and connect a Sharer (Router), refer to the owner’s manual for the corresponding
N
product.
You can connect the TV to the LAN directly without connecting it through a Sharer (Router).
N
If you use an IP Sharer (IP Router) that supports DHCP, you can set up the device as either DHCP or static IP.
N
For the procedures to use a static IP address, ask your Internet Service Provider.
N
Network Connection - Wireless
You can connect to the network wirelessly through a wireless IP sharer.
TV Side Panel
The LAN Port
on the Wall
Wireless IP sharer
LAN Cable
1. Connect the ‘Samsung Wireless LAN Adapter for InfoLive’ into the Wiselink terminal of the TV.
You must use the ‘Samsung Wireless LAN Adapter for InfoLive’(WIS-08BG) to use a wireless network.
N
The ‘Samsung Wireless LAN Adapter for InfoLive’ is sold separately. Contact a Samsung Electronics agent or service center
N
for purchasing.
To use a wireless network, your TV must be connected to a wireless IP sharer.
N
If the wireless IP sharer supports DHCP, you TV can use a DHCP or static IP address to connect to the wireless network.
N
You must use a wireless IP sharer that supports IEEE 802.11 B or IEEE 802.11G.
N
If the wireless IP sharer allows you to turn on / off the Ping connection function, turn it on.
N
Set the wireless IP sharer to Infrastructure mode. Ad-hoc mode is not supported.
N
Select a channel for the wireless IP sharer that is not currently being used. If the channel set for the wireless IP sharer is
N
currently being used by another device nearby, this will result in interference and communications may fail. When applying the security key for the AP (wireless IP sharer), only the following is supported.
N
1) Authentication Mode : WEP, WPAPSK, WPA2PSK
2) Encryption Type : WEP, TKIP, AES If you apply a security system other than the systems listed above, it will not work with the TV.
Samsung Wireless LAN
Adapter for InfoLive

Network Setup

Network Selection
Select Cable or Wireless as the method to connect to the network.
The menu is activated only if the ‘Samsung Wireless LAN Adapter’ for
N
InfoLive’ is connected.
Cable:
Connect to network using a cable.
Wireless:
Connect to network wirelessly.
Cable Network Setup
InternetProtocolSetup→AutoSetup/ManualSetup
Network Test:
When unable to connect to a wired network
N
You can test or conrm the network connection status after setting up the network.
If your Internet service provider has registered the MAC address of the device used to connect to the Internet for the rst time and authenticates the MAC address each time you connect to the Internet, your TV may not be able to connect to the Internet as the MAC address differs from that of the device (PC) used to connect to the Internet the rst time. In this case, ask your Internet service provider about the procedures to connect devices other than your PC (such as your TV) to the Internet. If your Internet service provider requires an ID or password to connect to the Internet (network), your TV may not be able to connect to the Internet. In this case, you have to enter your ID or password when connecting to the Internet using an Internet Sharer (Router).
The internet connection may fail due to a rewall problem. In this case, contact your Internet service provider. If you
cannot connect to the Internet even if you have followed the procedures of your Internet service provider, please contact a Samsung Electronics Service Center.
Wireless Network Setup
InternetProtocolSetup→AutoSetup/ManualSetup
Network Test: You can test or confirm the network connection status after setting up the network.
When unable to connect to a wireless network
N
Your TV may fail to locate an AP that is congured as a private SSID type. In this case, please change the AP settings and
try again. If your Internet service provider has registered the MAC address of the device used to connect to the Internet
for the rst time and authenticates the MAC address each time you connect to the Internet, your TV may not be able to connect to the Internet as the MAC address differs from that of the device (PC) used to connect to the Internet the rst time. In this case, ask your Internet service provider about the procedures to connect devices other than your PC (such as your TV) to the Internet. If you cannot connect to the Internet even if you have followed the procedures of your Internet
service provider, please contact a Samsung Electronics Service Center.
Select Access Point:
If a wireless Access Point is not in the Access Point list, press the Red button.
N
When the connection is made, you will be returned to the screen automatically.
N
If you selected an Access Point that requires security authentication, enter the security key.
N
If you have selected an Access Point with a security authentication:
N
The Security Key input screen appears.
-
Enter the security key and press the ENTERE button.
­Using the Remote Control Buttons on the Security Key Input Screen.
-
Setup Screen can be different depending on the security types.
N
You can select the IP sharer to use when using a wireless network.
Language : English
Time
Setup
NetworkSelection :Cable
Wireless Network Setup
Cable Network Setup Child Lock : On
Change PIN
Parental Lock Subtitle
Teletext Language : - - - -
Button Operations
▲/▼/◄/►,
(Wheel)
(ENTER)
Red button
Green button
Blue button
Moves the selection up/down/left/right.
Enters (Inputs) the selected character.
Switch between Upper- and Lower-Case Letters
You can delete an already entered character.
Press this button to nish entering the security key.
English - 30
Loading...
+ 311 hidden pages