Samsung PS-63P76FDR, PS-50P96FDR User Manual

PDP-TELEVISION
Contact SAMSUNG WORLD-WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.
Связывайтесь с SAMSUNG по всему миру
Если у вас есть предложения или вопросы по продуктам Samsung, связывайтесь с информационным центром Samsung.
Country
RUSSIA 8-800-200-0400 www.samsung.ru UKRAINE 8-800-502-0000 www.samsung.com/ur
Customer Care Centre
Web Site
(PLASMA DISPLAY PANEL)
PS-50P96FDR PS-63P76FDR
Owner’s Instructions
Before operating the unit,
and retain it for future reference.
BN68-01183N-00
ON-SCREEN MENUS
Picture In Picture (PIP)
Energy Saving TELETEXT (Option) SRS TruSurround XT
Digital Natural Image engine
Register your product at www.samsung.com/global/register Record your Model and Serial number here for future reference.
▪ Model _______________ ▪ Serial No. _______________

User Instructions

Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.
Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height so do not install and operate there.
Heat on the top of the PDP TV
The top side of the product may be hot after long period of use as heat dissipates from the panel through the vent hole in the upper part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children should be prevented from touching the upper part of the product.
The product is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as temperature or humidity. This is normal and not a defect of the unit.
Cell Defects
The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require sophisticated technology to produce. However, there may be few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product.
Avoid operating the TV at temperatures below 5°C(41°F)A still image displayed too long may cause permanent damage to the PDP Panel.
Afterimage on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may produce partial afterimages. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.
Warranty
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.
Installation
Be sure to contact an authorized service centre, when installing your set in a location with heavy dust, high or low temperatures, high humidity, chemical substance and where it operates continually such as the airport, the train station etc. Failure to do so may cause a serious damage to your set.
Watching the PDP TV in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and centre of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause similar effect to the screen. Damages caused by the above effect are not covered by the Warranty.
Any functions related to Digital TV (DVB) will only work in countries or areas where DVB-T (MPEG2) digital terrestrial signals are broadcasted. Please confirm with your local dealer if you can receive DVB-T signals. Although this TV set follows the DVB-T specification, maintaining compatibility with the future coming DVB-T digital terrestrial broadcasts is not guaranteed. Several functions may not be available in some countries.
© 2007 Samsung Electronics Co., Ltd. All rights reserved.
English - 2
English - 3

Contents

General Information
User Instructions .............................................2
Checking Parts ................................................ 4
Using the Stand-Base .....................................4
Control Panel ................................................. 5
Connection Panel ............................................ 6
Viewing the Remote Control .......................... 8
Operation
Switching Your Television On and Off ............. 9
Viewing the Menus ........................................ 10
Plug & Play Feature ......................................10
Viewing External Signal Sources ..................12
Editing Device Names ................................... 13
Channel Control
Storing Channels Automatically ....................13
Storing Channels Manually ...........................14
Adding / Locking Channels ........................... 15
Sorting the Stored Channels ......................... 16
Assigning Names to Channels ...................... 16
Fine Tuning Channel Reception .................... 17
LNA (Low Noise Amplifier) ............................ 17
Picture Control
Changing the Picture Standard ..................... 18
Customizing the Picture Settings ..................18
Configuring Detailed Settings on the Picture
Selecting the Picture Size .............................20
Selecting the Screen Mode ........................... 20
Digital NR / Active Colour / DNIe / Movie Plus
Freezing the Current Picture ......................... 21
.. 19
.. 21
Sound Control
Sound Features ............................................22
Selecting the Sound Mode (depending on
the model) .....................................................23
Function Description
Time Features ............................................... 24
Language / Blue Screen / Melody /
Energy Saving / HDMI Black Level ...............25
Using the Game Mode ..................................26
Wall- mount adjustment (Sold separately)
(PS-50P96FDR) ............................................ 27
Viewing the Picture in Picture (PIP) ..............28
Screen Burn Protection ................................. 29
PC Display
Setting up Your PC Software (Based on
Windows XP) ................................................ 30
Display Modes .............................................. 31
Setting the PC ............................................... 32
Setting the Home Theatre PC ....................... 33
Using the DTV Feature
Previewing the DTV Menu System ............... 34
Displaying Programme Information ............... 35
Operating the DTV Menu ..............................36
About Anynet+
What is Anynet+? ........................................46
Connecting Anynet+ Devices ........................46
Setting Up Anynet+ ....................................... 47
Scanning and Switching between Anynet+
Devices ......................................................... 47
Recording ...................................................... 48
Listening through a Receiver ........................ 49
Check Points before Requesting Service ..... 49
Appendix
Teletext Feature (depending on the model) .. 50
Wall Mount Kit Specifications (VESA) ........... 52
Setting Up Your Remote Control ................... 53
How to assemble the Stand-Base
(depending on the model) .............................58
Troubleshooting ............................................ 58
Specifications ................................................ 59
Symbols
Press
Important
Note

Checking Parts

Owner’s Instructions Remote Control/
Cover-Bottom /
Screws (2ea)
(PS-50P96FDR,
Refer to page 58)
S-Video Cable Antenna Cable Component Cables Audio Cables Video Cable
PC Cable Scart Cable PC Audio Cable HDMI Cable HDMI/DVI Cable
Ferrite Core (Power Cord, Audio/Video Cable, S-Video Cable,
Headphone) The ferrite core is used to shield the cable from interference. When connecting a cable, open the ferrite core and clip it around the cable.
AAA Batteries
Ferrite Core for
Power Cord/
S-Video Cable
Power Cord Cloth-Clean Warranty Card/
Ferrite Core for
Side-AV / S-VIDEO
Sold Separately
Ferrite Core for
Headphone
Registration Card/
Safety Guide Manual

Using the Stand-Base

Two or more people should carry
➢ 
the PDP. Never lay the PDP on the floor because of possible damage to the screen. Always keep the PDP upright.
 The PDP can rotate 20 degrees in
right and left directions.
-20° ~ 20°
English - 4
English - 5

Control Panel

Front (or Side) Panel
PS-50P96FDR
PS-63P76FDR
The product colour and shape may vary depending on the model.
1
SOURCE
Displays a menu of all of the available input sources (TV, Ext.1, Ext.2, AV, S-Video, Component, PC, HDMI1, HDMI2, HDMI3, and DTV).
In the on-screen menu, use this button as
you would use the ENTER/OK button on the remote control. (PS-50P96FDR)
2
MENU
Press to see the on-screen menu of your TV’s features.
3
+ VOL −
Press to increase or decrease the volume. In the on-screen menu, use the + VOL − buttons as you use the ◄ and ► buttons on the remote control.
4
CH
Press to change channels. In the on-screen menu, use the CH buttons as you use the ▲ and ▼ buttons on the remote control.
5
(ENTER)
Press to confirm a selection.
6
(Power) button
Press to turn the TV on and off.
Power Indicator
− Power Off: Blue
− Power On: Off
Remote Control Sensor
Aim the remote control towards this spot on the TV.
7
Speaker

Connection Panel

Side Panel
1
2
or
3
The product colour and shape may vary depending on the model.
1
HDMI IN 3
Connect to the HDMI jack of a device with HDMI output.
2
S-VIDEO or VIDEO / AUDIO L/R
Video (S-Video or Video) and audio inputs for external devices, such as a camcorder or VCR.
Rear Panel
1
3
Headphones jack
You can connect a set of headphones if you wish to watch a television programme without disturbing the other people in the room.
Prolonged use of headphones at a high
volume may damage your hearing.
0
or
Cable Television
Network
7
8
or
9
Continued...
6
2
The product colour and shape may vary depending on the model.
 Whenever you connect an audio or video system to your set, ensure that all elements are
switched off.
 When connecting an external device, match the colour of the connection terminal to the cable.
3
4
5
English - 6
English - 7
1
POWER IN
Connect the supplied power cord.
2
Connecting external Audio Devices
Connect RCA audio signals from the TV to an external source, such as Audio equipment.
3
EXT 1, EXT 2
Inputs or outputs for external devices, such as VCR, DVD, video game device or video disc players.
Input/Output Specification
Connector
EXT 1
EXT 2
4
COMPONENT IN
Input Output
Video Audio(L/R) RGB Video + Audio(L/R)
Only TV or DTV
output is available.
Output you can
choose.
Audio (AUDIO L/R) and video (Y/PB/PR) inputs for Component.
5
DIGITAL AUDIO OUT (OPTICAL)
Connect to a Digital Audio Component.
6
SERVICE
− Connector for service.
− Connect the serial jack between the electro-motion wall mount bracket and your TV when you want to adjust the TV viewing angle using your remote control.
7
PC IN / AUDIO
Connect to the video and audio output jack on your PC.
8
COMMON INTERFACE Slot
Insert CI (Common Interface) card into the slot. (refer to page 45)
− When not inserting “CI CARD” in some channels, “Scramble Signal” is displayed on the screen.
− The pairing information containing a telephone number, CI CARD ID, Host ID, and other information will be displayed in about 2~3 minutes. If an error message is displayed, please contact your service provider.
− When the channel information configuration has finished, the message “Updating Completed” is displayed, indicating that the channel list is now updated.
Insert the CI-Card in the direction marked
on it.
9
HDMI IN 1, HDMI IN 2
− Connect to the HDMI jack of a device with HDMI output. These inputs can also be used as a DVI connection with separate analog audio inputs. An optional HDMI/DVI cable will be necessary to make this connection. When using the optional HDMI/DVI adapter, the DVI analog audio inputs on your TV allow you to receive left and right audio from your DVI device. (Not compatible with PC)
− When connecting this product via HDMI or DVI to a Set Top Box, DVD Player or Games Console etc, make sure that it has been set to a compatible video output mode as shown in the table below. Failure to observe this may result in picture distortion, image breakup or no picture.
− Do not attempt to connect the HDMI/DVI connector to a PC or Laptop Graphics Card. (This will result in a blank screen being displayed)
− The TV may not output sound and pictures may be displayed with abnormal color when DVD players/Cable Boxes/Satellite receivers supporting HDMI versions older than 1.3 are connected. When connecting an older HDMI cable and there is no sound, connect the HDMI cable to the HDMI IN 1 jack and the audio cables to the DVI IN (HDMI2) [R-AUDIO-L] jacks on the back of the TV. If this happens, contact the company that provides the external device to confirm the HDMI version, then request an upgrade.
DVI IN (HDMI 2) AUDIO L/R
DVI audio outputs for external devices.
0
ANT IN
75Ω Coaxial connector for Aerial/Cable Network.
Supported modes for HDMI and Component
HDMI/DVI 50Hz X X X O O O O HDMI/DVI 60Hz X O X X O O O
Component O O O O O O O
480i 480p 576i 576p 720p 1080i 1080p

Viewing the Remote Control

This is a special remote control for the visually impaired persons, and has Braille points on the
➢ 
Power, Channel, Volume, STOP, and PLAY/PAUSE buttons.
 The performance of the remote control may be affected by bright light.
1
POWER button
(turns the TV on and off)
2
Number buttons for direct
channel access
3
One/Two-digit channel
selection
4
Channel control button
(Refer to page 15)
5
Selects the TV and DTV
mode directly
6
Volume increase
Volume decrease
7
Temporary sound switch-off
8
Displays the main on-screen
menu
9
Returns to the previous
menu
@
Picture size selection
#
Electronic Program Guide
(EPG) display
$
Sound mode selection
%
Remote control setup
^
Selects a target device to be
controlled by the Samsung remote control (TV, DVD, STB, CABLE, VCR)
&
Press to backlight the VOL,
CH, and the active source button (TV, DVD, CABLE, STB, VCR) on the remote.
*
Available source selection
(
Previous channel
)
DTV menu display
a
Records for Live
Broadcasting
b
VCR/DVD Function (Rewind,
Stop, Play/Pause, Fast/ Forward)
c
Next channel
Previous channel
d
Exit the on-screen menu
e
Control the cursor in the
menu
f
Use to see information on
the current broadcast
g
Runs the Anynet+ view
functions and sets up Anynet+ devices.
h
Picture-In-Picture On/Off
i
Picture effect selection
(Refer to page 18)
j
Digital subtitle display
k
Picture freeze
l
If your remote control is not
functioning properly, take out the batteries and press the reset button for about 2~3 seconds. Reinsert the batteries and try using the remote control again.
Teletext Functions
(Refer to page 50)
5
Exit from the teletext display
(depending on the model)
8
Teletext index
0
Fastext topic selection
!
Teletext display/mix both
teletext information and the normal broadcast
@
Teletext size
*
Teletext mode selection
(LIST/FLOF)
(
Teletext sub page
c
P :Teletext next page
P :Teletext previous page
d
Teletext cancel
f
Teletext reveal
h
Teletext hold
i
Teletext store
Continued...
English - 8
English - 9
Installing Batteries in the Remote Control 1 Lift the cover at the back of the remote control upward as
shown in the figure.
2 Install two AAA size batteries.
Make sure to match the “+” and “” ends of the
batteries with the diagram inside the compartment.
Do not mix battery types, i.e. alkaline and manganese.
3 Close the cover as shown in the figure.
Remove the batteries and store them in a cool and dry
place if you won’t be using the remote control for a long time. The remote control can be used up to about 23 feet from the TV. (Assuming typical TV usage, the batteries last for about one year.)
If the remote control doesn’t work! Check the following:
1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power cut, or is the power cord unplugged?
5. Is there a special fluorescent light or a neon sign nearby?

Switching Your Television On and Off

The main lead is attached to the rear of the television. 1 Plug the main lead into an appropriate socket.
The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.
2 Press the (Power) button (On/Off) on the front of the television or press the POWER button on the
remote control to switch the television on. The programme that you were watching last is reselected automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Storing Channels Automatically” on page 13 or “Storing Channels Manually” on page 14.
If the television is initially powered on, several basic customer settings proceed automatically.
Refer to “Plug & Play Feature” on page 10.
3 To switch the television off, press the (Power) button (On/Off) on the front of the television or press
the POWER button on the remote control.
4 To switch the TV on, press the (Power) button (On/Off) on the front of the TV or press the POWER
button or number buttons on the remote control.

Viewing the Menus

1 Press the MENU button.
The main menu is displayed on the screen. Its left side has five icons: Picture, Sound, Channel, Setup, and Input.
2 Press the ▲ or ▼ button to select one of the icons.
Press the ENTER/OK button to access the icon’s sub-menu.
3 Press the ▲ or ▼ button to move to items in the menu.
Press the ENTER/OK button to enter items in the menu.
4 Press the ▲/▼/◄/► button to change the selected items.
Press the RETURN button to return to the previous menu.
5 Press the EXIT button to exit from the menu.

Plug & Play Feature

When the television is initially powered on, several basic customer settings proceed automatically and subsequently. The following settings are available.
If you accidentally select the wrong country for your TV, the
characters on the screen may be wrongly displayed. Any functions related to Digital TV (DVB) will only work in
countries or areas where DVB-T (MPEG2) digital terrestrial signals are broadcasted. Please confirm with your local dealer if you can receive DVB-T signals. Although this TV set follows the DVB-T specification, maintaining compatibility with the future coming DVB-T digital terrestrial broadcasts is not guaranteed. Several functions may not be available in some countries.
1 If the television is in standby mode, press the POWER button
on the remote control. The message Start Plug & Play is displayed. Press the ENTER/OK button.
2 The Language menu will automatically appear after several
seconds.
3 Select the appropriate language by pressing the ▲ or ▼ button.
Press the ENTER/OK button. The message Select Home
Mode when installing this TV at home. is displayed.
4 Press the ◄ or ► button to select Shop or Home, then press
the ENTER/OK button. The message to check the connected status of the antenna is displayed.
The default selection is Home.
We recommend setting the TV to Home mode for the best
picture in your home environment. Shop mode is only intended for use in retail environments.
If the unit is accidentally set to Shop mode, and you want to
return to Dynamic (Home) mode, press the Volume button and then hold down the MENU button for five seconds on the TV panel.
5 Make sure that the antenna is connected to the TV.
Press the ENTER/OK button. The Country menu is displayed.
T V
Mode : Contrast 100 Brightness 45 Sharpness 75 Colour 55 Tint G 50 R 50 Colour Tone :
Detailed Settings
More
Language
Move
Select Home Mode When installing this TV at home.
Shop
Move
Country
Move
Picture
Move
Plug & Play
Start Plug & Play.
OK
Enter
Plug & Play
English
Deutsch Français
Italiano
Enter
Plug & Play
Enter
Plug & Play
Check antenna input.
OK
Enter
Plug & Play
United Kingdom
Austria
Eastern Europe
Enter
Dynamic
Cool1
Enter
Exit
Skip
Home
Skip
Skip
Skip
Exit
English - 10
Continued...
English - 11
6 Select your country or area by pressing the ▲ or ▼ button.
Press the ENTER/OK button. The message Some DTV functions may not be available. Digitally Scan? is displayed.
This function is supported for all countries except for the
following 6 countries: the United Kingdom, Austria, France, Germany, Italy, Spain.
If your country supports the DTV functions, the message is not displayed. Then you can follow the instructions from step
12. When the local service provider does not support DTV broadcasting but you choose a DTV supporting country, it enters the DTV Plug & Play but DTV functions may not work properly.When No is selected, follow the instructions from step 7 to 10. When Yes is selected, follow the instructions from step 11.
7 Select No pressing the ◄ or ► button, then press the ENTER/
OK button. Auto Store menu is displayed.
8 Press the ENTER/OK button to start search the channels. The
channel search will start and end automatically. After all the available channels are stored, Clock Set menu is automatically displayed. Press the ENTER/OK button.
To stop the search before it has finished, press the
ENTER/OK button with Stop selected.
Some DTV functions may not be available.
Auto Store P 1 C -- 40 MHz 0 %
Clock Set
Month Day Year Hour
01 01
Move
Adjust
Plug & Play
Digitally Scan?
Yes
Plug & Play
Plug & Play
2007
Plug & Play
Enter
Enter
Move
Start
00
No
:
Skip
Skip
Minute
00
Enter
9 Press the ◄ or ► button to select Month, Day, Year, Hour, or
Minute. Set these by pressing the ▲ or ▼ button.
You can set the Month, Day, Year, Hour, or Minute
directly by pressing the numeric buttons on the remote control.
10 Press the ENTER/OK button to confirm your setting. The
message Enjoy your viewing is displayed. When you have finished, press the ENTER/OK button.
Even if the ENTER/OK button is not pressed, the message
will automatically disappear after several seconds.
11
Select Yes pressing the ◄ or ► button, then press the
ENTER/OK button. Auto Store menu is displayed.
12 Press the ENTER/OK button to start search the analog
channels. The analog channel search will start and end automatically. After all the available analog channels are stored, the screen for searching digital channels is automatically displayed.
To stop the search before it has finished, press the
ENTER/OK button with Stop selected.
13 Press the ENTER/OK button to start search the digital
channels. The digital channel search will start and end automatically.
After all the available digital channels are stored,
0% Services found: 0 Channel:
Skip
Plug & Play
Scanning for digital services...
29% Services found: 6 Channel: 35
Skip
Plug & Play
The Iberian Peninsula and Balears Islands
Canarian Islands
-
Start
Stop
the screen to select a time zone is displayed depending on the country.
To stop the search before it has finished, press the
ENTER/OK button with Stop selected. If the DTV channel is updated, the Source in the source list
of the Input menu is automatically changed to DTV. For detailed descriptions about DTV channel update, refer
to page 36 of this manual.
Move Select
Skip
14 Press the ▲ or ▼ button to select required time zone, then press the ENTER/OK button. The screen
for setting the time is displayed. Press the ENTER/OK button.
Continued...
15 Press the ◄ or ► button to select Month, Day, Year, Hour, or
Minute. Set these by pressing the ▲ or ▼ button.
You can set the Month, Day, Year, Hour, or Minute
directly by pressing the numeric buttons on the remote control.
16 Press the ENTER/OK button to confirm your setting. The
message Enjoy your viewing is displayed. When you have finished, press the ENTER/OK button.
Even if the ENTER/OK button is not pressed, the message
will automatically disappear after several seconds.
If you want to reset this feature … 1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Setup, then press the
ENTER/OK button.
3 Press the ENTER/OK button again to select Plug & Play.
The message Start Plug & Play is displayed.

Viewing External Signal Sources

Set the current time.
Adjust
T V
Plug & Play
Month Day Year
01
Hour Minute
12 00
Move
Enjoy your viewing
Plug & Play Language : Time
Game Mode : Off
Blue Screen : Melody :
PC Home Theatre PC : Off
More
Move
15
OK
Setup
2007
Select
English
Off Off
Enter
Skip
Return
You can switch between viewing signals from connected equipment, such as a VCR, DVD, Set-Top Box, and the TV
T V
source (broadcast or cable). 1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Input, then press the
ENTER/OK button. 3 Press the ENTER/OK button again to select Source List. 4 Press the ▲ or ▼ button to select the signal source, then press
the ENTER/OK button. Available signal sources:
Component, PC, HDMI1, HDMI2, HDMI3, DTV
You can select these options simply by pressing the SOURCE
button on the remote control.
To watch television programme again, press the TV/DTV button
and select the channel number required.
TV, Ext.1, Ext.2, AV, S-Video,
English - 12
T V
Move
Move
Input
Source List
Enter
−−−−
−−−−
−−−−
−−−−
−−−−
−−−−
−−−−
−−−−
Enter
Source List : TV Edit Name Anynet+(HDMI-CEC)
TV Ext.1 : Ext.2 : AV : −−−− S-Video : Component : PC : HDMI1 : HDMI2 : −−−− HDMI3 : DTV :
Return
Return
English - 13

Editing Device Names

You can give a name to the external source.
T V
1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Input, then press the
ENTER/OK button. 3 Press the ▲ or ▼ button to select Edit Name, then press the
ENTER/OK button. 4 Press the ▲ or ▼ button to select the external source to be
edited, then press the ENTER/OK button. 5 Select the required device by pressing ▲ or ▼, then press the
ENTER/OK button.
Available device names:
VCR, DVD, D-VHS, Cable STB, HD
T V
STB, Satellite STB, AV Receiver, DVD Receiver, Game,
Camcorder, DVD Combo, DHR (DVD HDD Recorder), PC. 6 Press the EXIT button to exit.
When a PC with a resolution of 1920 x 1080@60Hz is
connected to the HDMI IN 1 port, you should set the HDMI1 mode to PC in the Source List of the Input mode. If the HDMI1 mode is not PC, it works depending on the TV setting.

Storing Channels Automatically

Not available in DTV or external input mode.
You can scan for the frequency ranges available to you (availability depends on your country). Automatically allocated programme numbers may not correspond to actual or desired programme numbers. However you can sort numbers manually and clear any channels you do not wish to watch.
1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button. 3 Press the ENTER/OK button again. The available countries are
listed. 4 Select your country by pressing the ▲ or ▼ button, then press
the ENTER/OK button.
Even though you have changed the country setting in this
menu, the country setting for DTV is not changed. Use the Plug & Play function to change the country setting for DTV. (Refer to page 10 to 12)
5 Press the ▲ or ▼ button to select Auto Store, then press the
ENTER/OK button. 6 Press the ENTER/OK button again to start the search.
The search will end automatically.
To stop the search before it has finished, press the MENU
or the ENTER/OK button.
T V
T V
Input
Edit Name
Channel
Channel
Auto Store
Start
Enter
TV
Enter
−−−−
−−−−
VCR
−−−−
DVD
−−−−
D-VHS
−−−−
Cable STB
−−−−
HD STB
−−−−
Satellite STB
−−−−
−−−−
Enter
United Kingdom
Switzerland
United Kingdom
Austria
Eastern Europe
Others
Off
Enter
United Kingdom 
Off
Enter
Return
Return
Return
Return
Return
Source List : Edit Name Anynet+(HDMI-CEC)
Move
Ext.1 : −−−−
Ext.2 : AV : S-Video : Component : PC : HDMI1 : HDMI2 : HDMI3 :
Move
Country :
Auto Store Manual Store Channel Manager Sort Name Fine Tune LNA :
Move
Country : Auto Store Manual Store Channel Manager Sort Name Fine Tune LNA :
Move
P 1 C -- 40 MHz 0 %
     

Storing Channels Manually

Not available in DTV or external input mode.
You can store television channels, including those received via cable networks. When storing channels manually, you can choose:
Whether or not to store each of the channels found.The programme number of each stored channel which you wish
to identify.
T V
Country : Auto Store Manual Store Channel Manager Sort Name Fine Tune LNA :
Channel
United Kingdom
Off
1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button. 3 Press the ▲ or ▼ button to select Manual Store, then press
T V
the ENTER/OK button. 4 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button. 5 When you are satisfied with your setting, press the ENTER/OK
Move
Manual Store
Programme : Colour System : Sound System : Channel : Search : Store :
Enter
P 1 Auto BG C 4 63 MHz ?
Return
button.
6 Press the EXIT button to exit.
Move
Enter
Programme (Programme number to be assigned to a channel)
Return
− Press the ▲ or ▼ button until you find the correct number. You can also select the channel number directly by pressing the numeric buttons (0~9).
Colour System: Auto/PAL/SECAM/NTSC4.43
− Press the ▲ or ▼ button to select the required colour standard.
Sound System: BG/DK/I/L
− Press the ▲ or ▼ button to select the required sound standard.
Channel (When you know the number of the channel to be stored)
− Press the ▲ or ▼ button to select C (Air channel) or S (Cable channel).
− Press the ► button, then press the ▲ or ▼ button to select the required number. You can also select the channel number directly by pressing the numeric buttons (0~9).
If there is abnormal sound or no sound, reselect the sound standard required.
Search (When you do not know the channel numbers)
− Press the ▲ or ▼ button to start the search.
− The tuner scans the frequency range until the first channel or the channel that you selected is
received on the screen.
Store (When you store the channel and associated programme number)
− Set to OK by pressing the ENTER/OK button.
Channel mode
P (Programme mode): When completing tuning, the broadcasting stations in your area have
been assigned to position numbers from P00 to P99. You can select a channel by entering the position number in this mode.
C (Air channel mode): You can select a channel by entering the assigned number to each air
broadcasting station in this mode.
S (Cable channel mode): You can select a channel by entering the assigned number for each
cable channel in this mode.
      
English - 14
English - 15

Adding / Locking Channels

Not available in DTV or external input mode.
Using the Channel Manager, you can conveniently lock or add
T V
channels. 1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button.
3 Press the ▲ or ▼ button to select Channel Manager, then
press the ENTER/OK button.
Adding channels
Using the Channel List, you can add channels.
T V
4 Select Channel List by pressing the ENTER/OK button. 5 Move to the ( ) field by pressing the ▲/▼/◄/► buttons,
select a channel to be added, and press the ENTER/OK button to add the channel.
If you press the ENTER/OK button again, the ( ) symbol
next to the channel disappears and the channel is not added.
Locking channels
This feature allows you to prevent unauthorized users, such as children, from watching unsuitable programmes by muting out video and audio.
6 Press the ▲ or ▼ button to select Child Lock, then press the ENTER/
OK button.
7 Select On by pressing the ▲ or ▼ button, then press the ENTER/OK
button.
8 Press the ▲ or ▼ button to select Channel List, then press the
ENTER/OK button.
9 Move to the ( ) field by pressing the ▲/▼/◄/► buttons, select a
channel to be locked, and press the ENTER/OK button.
If you press the ENTER/OK button again, the ( ) symbol next to
the channel disappears and the channel lock is canceled. A blue screen is displayed when Child Lock is activated.
10 Press the EXIT button to exit.
You can select these options simply by pressing the CH LIST
button on the remote control.
Channel
Country : Auto Store Manual Store Channel Manager Sort Name Fine Tune LNA :
Move
Channel List Child Lock :
Move
P 1 C 4
Prog. 0 C -
1 C 4 2 C 24 3 C 2 4 C 5 5 C 80 6 C 7 7 C 36 8 C 52 9 C 11
Add Lock Move Enter
Page
United Kingdom
Off
Enter
Channel Manager
Off
Enter
Channel List
-
Return
      
Return
Return
1 / 10

Sorting the Stored Channels

Not available in DTV or external input mode.
This operation allows you to change the programme numbers
T V
of the stored channels. This operation may be necessary after using the auto store.
1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button.
3 Press the ▲ or ▼ button to select Sort, then press the ENTER/
OK button.
4 Select the channel that you wish to move by pressing the ▲ or
▼ button, then press the ENTER/OK button.
T V
5 Select the number of the programme to which the channel is to
be moved by pressing the ▲ or ▼ button. Press the ENTER/OK button. The channel is moved to its new position and all other channels are shifted accordingly.
6 Repeat steps 4 to 5 until you have moved all the channels to
the required programme numbers.
7 Press the EXIT button to exit.

Assigning Names to Channels

Not available in DTV or external input mode.
Channel names will be assigned automatically when channel information is broadcast. These names can be changed, allowing you to assign new names.
1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button.
3 Press the ▲ or ▼ button to select Name, then press the
ENTER/OK button.
4 Press the ▲ or ▼ button to select the channel to be assigned to
a new name, then press the ENTER/OK button.
5 Press the ▲ or ▼ button to select a letter, a number, or a
symbol (Results in this sequence: A~Z, 0~9, +, -, *, /, blank). Move on to the previous or next letter by pressing the ◄ or ► button, then press the ENTER/OK button.
6 Repeat steps 4 to 5 for each channel to be assigned to a new
name.
7 Press the EXIT button to exit.
T V
T V
Channel
United Kingdom
Country : Auto Store Manual Store Channel Manager Sort Name Fine Tune LNA :
Move
Move
Move
Move
Enter
Sort
Enter
Channel
Enter
Name
Enter
Prog. Ch. Name
0 C−− 1 C76 2 C5 3 C6 4 C7
Country : Auto Store Manual Store Channel Manager Sort Name Fine Tune LNA :
Prog. Ch. Name
0 C−− −−−−− 1 C76 −−−−− 2 C5 −−−−− 3 C6 −−−−− 4 C7 −−−−−
      
Off
Return
Return
United Kingdom
      
Off
Return
Return
English - 16
English - 17

Fine Tuning Channel Reception

Not available in DTV or external input mode.
If the reception is clear, you do not have to fine tune the
T V
channel, as this is done automatically during the search and store operation. If the signal is weak or distorted, you may have to fine tune the channel manually.
1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button.
3 Press the ▲ or ▼ button to select Fine Tune, then press the
ENTER/OK button.
4 To obtain a sharp, and clear picture and good sound quality,
press the ◄ or ► button until you reach the optimal setting. Press the ENTER/OK button.
To reset the fine tuning to 0, select Reset by pressing the
▲ or ▼ button. Press the ENTER/OK button.
P 1 +3
5 Press the EXIT button to exit.
Fine Tune Store will change the colour of the Channel OSD
(On Screen Display) from White to Red and add the “*” mark.
P 1 * Mono
Picture : Dynamic Sound : Custom SRS TS XT : Off
−−

LNA (Low Noise Amplifier)

This function is very useful in the situation that the TV is used in weak signal. LNA amplifies the TV signal in the weak signal area, a low-noise preamplifier boosts the incoming signal.
1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button.
3 Press the ▲ or ▼ button to select LNA, then press the ENTER/
OK button.
4 Select Off or On by pressing the ▲ or ▼ button, then press the
ENTER/OK button.
5 Press the EXIT button to exit.
Depending on areas, factory mode of LNA, will be set up as On or Off.
T V
Country : Auto Store Manual Store Channel Manager Sort Name Fine Tune LNA :
Adjust
:
−−
Country : Auto Store Manual Store Channel Manager Sort Name Fine Tune LNA :
Move
Move
Fine Tune
Reset
Save
Channel
United Kingdom
Off
Enter
Channel
United Kingdom
Off
Enter
Return
      
Return
      
Return

Changing the Picture Standard

You can select the type of picture which best corresponds to your viewing requirements.
1 Press the MENU button to display the menu. 2 Press the ENTER/OK button to select Picture. 3 Press the ENTER/OK button again to select Mode. 4 Select the required mode by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available modes:
The settings values may vary depending on the input
source. (ex. RF, Video, Component, PC, or HDMI)
Dynamic, Standard, Movie
5 Press the EXIT button to exit.
You can select these options simply by pressing the P.MODE
button on the remote control.
Choose Dynamic for viewing the TV during the day or
➢ 
when there is bright light in the room.
Choose Standard for general TV watching mode. Choose Movie when viewing the movie.
T V
Mode : Contrast 100 Brightness 45 Sharpness 75 Colour 55 Tint G 50 R 50 Colour Tone :
Detailed Settings
More
Move
T V
Mode : Dynamic
Contrast 100 Brightness 45 Sharpness 75 Colour 55 Tint G 50 R 50 Colour Tone :
Detailed Settings
More
Move

Customizing the Picture Settings

Your television has several setting options that allow you to control the picture quality.
1 Press the MENU button to display the menu. 2 Press the ENTER/OK button to select Picture. 3 Press the ENTER/OK button again to select Mode. 4 Select the required mode by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available modes:
Dynamic, Standard, Movie
5 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
6 When you are satisfied with your setting, press the ENTER/OK
button.
7 Press the EXIT button to exit. Contrast – BrightnessSharpnessColourTint
In TV, AV, S-Video modes of the PAL system, you cannot
use the Tint Function.
Contrast – BrightnessColour Tone : PC Mode
Press the ◄ or ► button until you reach the optimal setting.
Colour Tone: Cool2/Cool1/Normal/Warm1/Warm2
When the picture mode is set to Dynamic or Standard, Warm1 and Warm2 cannot be selected.
Reset: Cancel/OK Select
OK. You can return to the factory defaults picture settings.
The reset function is set for each picture mode and colour tone.
T V
Mode : Contrast 100 Brightness 45 Sharpness 75 Colour 55 Tint G 50 R 50 Colour Tone :
Detailed Settings
More
Move
T V
Mode : Dynamic Contrast 100 Brightness 45 Sharpness 75 Colour 55 Tint G 50 R 50
: Cool1
Colour Tone
Detailed Settings
More
Move
Picture
Dynamic
Cool1
Enter
Picture
Cool1
Enter
Picture
Dynamic
Cool1
Enter
Picture
Enter
Dynamic
Standard
Movie
Cool2
Cool1
Normal
Warm1 Warm2
Return
Return
Return
Return
English - 18
English - 19

Configuring Detailed Settings on the Picture

You can set detailed picture settings. 1 Press the MENU button to display the menu. 2 Press the ENTER/OK button to select Picture. 3 Press the ▲ or ▼ button to select Detailed Settings, then
press the ENTER/OK button.
4 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available options: Black Adjust
, Dynamic Contrast, Gamma,
White Balance, My Colour Control, Edge Enhancement, Colour Space, xvYCC
5 When you are satisfied with your setting, press the ENTER/OK
button.
6 Press the EXIT button to exit.
When the picture mode is set to Movie or Standard, Detailed
Settings can be selected. If DNIe is Off, the Detailed Settings cannot be selected when
the Picture mode is in Standard mode.
T V
Mode : Contrast 80 Brightness 45 Sharpness 10 Colour 53 Tint G 50 R 50 Colour Tone : Detailed Settings
More
T V
Black Adjust : Off Dynamic Contrast : Gamma : White Balance My Colour Control Edge Enhancement Colour Space : xvYCC : Off
Move
Detailed Settings
Move
Picture
Movie
Warm2
Enter
Return
Off 0
: Off
Auto
Enter
Return
Black Adjust: Off/Low/Medium/High
You can directly select the black level on the screen to adjust the screen depth.
Dynamic Contrast: Off/Low/Medium/High
You can adjust the screen contrast so that the optimal contrast is provided.
Gamma: -3 ~ +3
You can adjust the middle brightness of pictures. Press the ◄ or ► button until you reach the optimal setting.
White Balance: R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain/Reset
You can adjust the colour temperature for more natural picture colors. R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain: Changing the adjustment value will refresh the adjusted screen. Select the required option by pressing the ▲ or ▼ button, then press the ENTER/OK button. Press the ◄ or ► button until you reach the optimal setting. Reset: The previously adjusted white balance will be reset to the factory defaults.
My Colour Control: Pink/Green/Blue/White/Reset
This setting can be adjusted to suit your personal preferences. Pink/Green/Blue/White: Changing the adjustment value will refresh the adjusted screen. Select the required option by pressing the ▲ or ▼ button, then press the ENTER/OK button. Press the ◄ or ► button until you reach the optimal setting. Reset: The previously adjusted colours will be reset to the factory defaults.
Edge Enhancement: Off/On
You can emphasize object boundaries.
Colour Space: Auto/Wide
You can set the colour reproduction space for the input signal to Auto or Wide.
xvYCC: Off/On Setting the xvYCC mode to On increases detail and colour space when watching movies from an
external device (ie. DVD player) connected to the HDMI or Component IN jacks. You must set the Picture Mode to Movie to enjoy this feature.
The xvYCC function works only in Component or HDMI mode.

Selecting the Picture Size

You can select the picture size which best corresponds to your viewing requirements.
1 Press the MENU button to display the menu. 2 Press the ENTER/OK button to select Picture. 3 Press the ▲ or ▼ button to select Size, then press the ENTER/
OK button.
4 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available options: Auto Wide
, 16:9, Wide Zoom, Zoom, 4:3,
Just Scan
Auto Wide: Expands and pulls up the picture from 4:3 to
16:9 ratio.
16:9: Sets the picture to 16:9 wide mode.Wide Zoom: Magnifies the size of the picture more than
4:3. Move the screen up/down using the ▲ or ▼ button
T V
More Size : Screen Mode : 16 : 9 Digital NR : Active Colour : On DNIe : Movie Plus : Reset :
Move
T V
Auto Wide 16:9 Wide Zoom Zoom 4:3 Just Scan
Picture
Auto Wide
Auto
On On OK
Enter
Size
Return
after selecting the by pressing the ► or ENTER/OK button.
Zoom: Magnifies the size of the picture vertically on
screen.
Move
Enter
Return
4:3: Sets the picture to 4:3 normal mode.Just Scan: Displays the input scenes as they are without
any cutoff when HDMI 720p, 1080i, 1080p signals are input.
With the HDMI Just Scan picture size, depending on
the AV devices, the screen may be cut off or a specific colour appears on the screen.
5 Press the EXIT button to exit.
You can change the picture size simply by pressing the P.SIZE button on the remote control.
Depending on the input source, the picture size options may vary.
The items available may differ depending on the selected mode.
Positioning and Sizing the screen using Zoom
Resizing the screen using the Zoom enables the positioning and sizing of the screen to up/down
direction using the ▲ or ▼ button as well as the screen size.
Move the screen up/down using the ▲ or ▼ button after selecting the by pressing the ◄ or ►
button.
Resize the screen vertically using the ▲ or ▼ button after selecting the by pressing the ◄ or ►
button.

Selecting the Screen Mode

When setting the picture size to Auto Wide in a 16:9 wide TV, you can determine the picture size you want to see the 4:3
T V
WSS (Wide Screen Service) image or nothing. Each individual European country requires different picture size so this function is intended for users to select it.
1 Press the MENU button to display the menu. 2 Press the ENTER/OK button to select Picture. 3 Press the ▲ or ▼ button to select Screen Mode, then press
the ENTER/OK button.
4 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available options:
16:9, Wide Zoom, Zoom, 4:3
16:9: Sets the picture to 16:9 wide mode.Wide Zoom: Magnifies the size of the picture more than 4:3. Zoom: Magnifies the size of the picture vertically on screen.4:3: Sets the picture to 4:3 normal mode.
5 When you are satisfied with your setting, press the ENTER/OK button. 6 Press the EXIT button to exit.
English - 20
Move
Picture
Auto Wide
Auto
On On OK
Enter
More Size : Screen Mode : 16 : 9 Digital NR : Active Colour : On DNIe : Movie Plus : Reset :
Return
English - 21

Digital NR / Active Colour / DNIe / Movie Plus

1 Press the MENU button to display the menu.
T V
2 Press the ENTER/OK button to select Picture. 3 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available options:
Digital NR, Active Colour, DNIe, Movie
Plus
More Size : Screen Mode : 16 : 9 Digital NR : Active Colour : On DNIe : Movie Plus : Reset :
Picture
Auto Wide
Auto
On On OK
4 When you are satisfied with your setting, press the ENTER/OK
button.
5 Press the EXIT button to exit.
Move
Enter
Return
Digital NR: Off/Low/Medium/High/Auto
If the signal received by the television is weak, you can activate this feature to reduce any static and ghosting that may appear on the screen.
Active Colour: Off/On
If you turn on this option, the colours of the sky and grass will be stronger and clearer for a more vivid on-screen picture.
This function is not available in PC mode.
This function is not available in Movie and Standard mode.
DNIe: Off/Demo/On
This TV includes the DNIe function so as to provide a high visual quality. If you set DNIe to on, you can view the screen with the DNIe feature activated. If you set the DNIe to Demo, you can view the applied DNIe and normal pictures on the screen, for demonstration purposes. Using this function, you can view the difference in the visual quality.
DNIeTM (Digital Natural Image engine)
This feature brings you more detailed image with 3D noise reduction, detail enhancement, contrast enhancement and white enhancement. New image compensation Algorithm gives brighter, clearer, more detailed image to you. DNIeTM technology will fit every signal into your eyes. This function is not available in PC mode.
Movie Plus: Off/On
You can view more natural skin and clear text even in fast moving scenes.
The Wide Zoom, Zoom and Just Scan mode are not supported.

Freezing the Current Picture

You can freeze the picture when watching a television programme simply by pressing the “STILL” button. To return to normal viewing, press it again.
This function will automatically cancel five minutes later.

Sound Features

1 Press the MENU button to display the menu.
T V
2 Press the ▲ or ▼ button to select Sound, then press the
ENTER/OK button.
3 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available options: Mode, Equalizer, SRS TS XT, Auto Volume
,
Mode : Equalizer SRS TS XT : Auto Volume Internal Mute :
Sound Select : Main Reset
Sound
Custom
Off
: Off
Off
Internal Mute, Sound Select, Reset
4 When you are satisfied with your setting, press the ENTER/OK
button.
5 Press the EXIT button to exit. Mode: Standard/Music/Movie/Speech/Custom
You can select the type of special sound effect to be used when watching a given broadcast.
Equalizer: Balance/100Hz/300Hz/1kHz/3kHz/10kHz
The television has several settings which allow you to control the sound quality.
If you make any changes to these settings, the sound mode
is automatically switched to Custom.
SRS TS XT: Off/On
TruSurround XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers. TruSurround delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal television speakers. It is fully compatible with all multichannel formats.
TruSurround XT, SRS and
Symbol are trademarks of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc.
< If Game Mode is On >
T V
T V
Move
Mode : Custom
Equalizer SRS TS XT : Auto Volume Internal Mute :
Sound Select : Main
Reset
Enter
Sound
Off
: Off
Off
Move
Enter
Equalizer
R
+
0
-
L
Balance 100Hz 300Hz 1kHz 3kHz 10kHz
Move Adjust
Return
Return
+
0
-
Return
Auto Volume: Off/On
Each broadcasting station has its own signal conditions, and so it is not easy to adjust the volume every time the channel is changed. This feature lets you automatically adjust the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low.
Internal Mute: Off/On
If you want to hear the sound through separate speakers, cancel the internal amplifier.
The +, - and MUTE buttons do not operate when the Internal Mute is set to On.
When Internal Mute is set to On, the Sound menus except for Sound Select (in PIP mode)
cannot be adjusted.
Sound Select: Main/Sub
When the PIP feature is activated, you can listen to the sound of the sub (PIP) picture.
Main: Used to listen to the sound of the main picture.
Sub: Used to listen to the sound of the sub picture.
Reset
If Game Mode is On, the Reset Sound function is activated. Selecting the Reset function after setting the equalizer resets the equalizer setting to the factory defaults.
TRADEMARK & LABEL LICENSE NOTICE
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
English - 22
English - 23

Selecting the Sound Mode (depending on the model)

The DUAL I-II button displays/controls the processing and output of the audio signal. When power is switched on, the mode is automatically preset to either “DUAL-I” or “Stereo”, depending on the current transmission.
Type of broadcast On-screen indication
Regular broadcast
(Standard audio)
Regular + NICAM Mono NICAM
NICAM
Stereo
NICAM Stereo
Mono (Normal use)
NICAM
stereo
Mono
(Normal)
Mono
(Normal)
NICAM DUAL-I/II
Regular broadcast
A2
Stereo
➢ 
(Standard audio)
Bilingual or DUAL-I/II Dual I
Stereo Stereo
If the receiving conditions deteriorate, listening will be easier if the mode is set to Mono. If the stereo signal is weak and automatic switching occurs, switch to Mono. When receiving a mono sound in the AV mode, connect to the “AUDIO-L” input connector on the
panel (front or side). If the mono sound comes out only from the left speaker, press the DUAL I-II
NICAM
dual-1
NICAM
dual-2
Mono (Normal use)
Mono
(Normal)
Dual II
Mono
(Forced mono)
button.

Time Features

1 Press the MENU button to display the menu.
T V
2 Press the ▲ or ▼ button to select Setup, then press the
ENTER/OK button.
3 Press the ▲ or ▼ button to select Time, then press the
ENTER/OK button.
4 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available options:
Clock Set, Sleep Timer, Timer 1, Timer 2,
Timer 3
5 When you are satisfied with your setting, press the ENTER/OK
T V
button.
6 Press the EXIT button to exit.
Clock Set
You can set the television clock so that the current time is
Plug & Play Language : Time
Game Mode : Off
Blue Screen : Melody :
PC Home Theatre PC : Off
More
Clock Set : 00 : 00 Sleep Timer : Timer 1 : Timer 2 : Timer 3 :
Move
Setup
English
Off Off
Enter
Time
Off Inactivated Inactivated Inactivated
displayed when pressing the INFO button on the remote control. You must also set the time if you wish to use the automatic on or off timers.
− Press the ◄ or ► button to select Month, Day, Year, Hour, or Minute. Set these by pressing the ▲ or ▼ button.
You can set the Month, Day, Year, Hour, or Minute
directly by pressing the numeric buttons on the remote control. In the event of a power interruption or the set being turned
off at the supply, the settings for the Clock will be lost.
Sleep Timer
You can select a time period of between 30 and 180 minutes after which the television automatically switches to standby mode.
T V
Move
Timer 1
On Time
00 : 00 No
Off Time
00 : 00 No
Repeat Volume
Once 10
Programme
01
Move Adjust
Enter
− Select the preset time interval (Off, 30, 60, 90, 120, 150, or
180) for staying on by pressing the ▲ or ▼ button.
Timer 1 / Timer 2 / Timer 3
You can set the On/Off timers so that the television will switch on or off automatically at the time you select.
You must set the clock first.
− Press the ◄ or ► button to select the required item below.
Press the ▲ or ▼ button to adjust to the setting satisfied.
On Time : Select hour, minute, and No/Yes. (To activate timer with the setting satisfied, set to Yes.) Off Time : Select hour, minute, and No/Yes. (To activate timer with the setting satisfied, set to Yes.) Repeat : Select Once, Everyday, Mon~Fri, Mon~Sat, or Sat~Sun. Volume : Select the required volume level. Programme : Select the required channel.
You can set the hour, minute, and channel directly by pressing the number buttons on the remote
control.
Auto Power Off
When you set the timer “On”, the TV will eventually turn off, if no controls are operated for 3 hours after the TV was turned on by the timer. This function is only available in timer “On” mode and prevents overheating, which may occur if a TV is on for too long time.
Return
Return
Return
English - 24
English - 25
Language / Blue Screen / Melody / Energy Saving / HDMI Black Level
1 Press the MENU button to display the menu.
T V
2 Press the ▲ or ▼ button to select Setup, then press the
ENTER/OK button.
3 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available options:
Language, Blue Screen, Melody, Energy
Saving, HDMI Black Level
4 When you are satisfied with your setting, press the ENTER/OK
button.
5 Press the EXIT button to exit.
T V
Language
It is variable depending on the model. When you start using the television for the first time, you must select the language which will be used for displaying menus and indications.
Plug & Play Language : Time
Game Mode : Off
Blue Screen : Melody :
PC Home Theatre PC : Off
More
More
Wall-
Energy Saving : Off HDMI Black Level : PIP Screen Burn Protection
Setup
English
Off Off
Move
Enter
Setup
Mount Adjustment
Return
Normal
Blue Screen: On/Off
If no signal is being received or the signal is very weak, a blue screen automatically replaces the noisy picture background. If you wish to continue viewing the poor picture, you must set the
Move
Enter
Return
Blue Screen to Off.
Melody: Off/Low/Medium/High
The TV power on/off melody sound can be adjusted.
Energy Saving: Off/Low/Medium/High
This feature adjusts the screen brightness depending on the surrounding lighting conditions.
Off: Switches off the Energy Saving mode.
Low: Operates in standard mode regardless of the surrounding illumination.
Medium: Enters Medium power saving mode regardless of the surrounding illumination.
High: Enters maximum power saving mode regardless of the surrounding illumination.
HDMI Black Level: Normal/Low
Using this function, you can adjust the image quality when the screen burn (appearance of black level, low contrast, low colour, etc.) is encountered by the HDMI input for RGB limited range (16 to
235).
This function is active only when the externel input connects to HDMI(RGB signals).

Using the Game Mode

When connecting to a game console such as PlayStationTM or XboxTM, you can enjoy a more realistic gaming experience by selecting game menu.
1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Setup, then press the
ENTER/OK button.
3 Press the ▲ or ▼ button to select Game Mode, then press the
ENTER/OK button.
4 Select Off or On by pressing the ▲ or ▼ button, then press the
ENTER/OK button.
T V
Plug & Play
Language : Time Game Mode : Off Blue Screen : Melody :
PC Home Theatre PC : Off
More
Move
Setup
English
Off Off
Enter
5 Press the EXIT button to exit.
To disconnect the game console and connect another external device, cancel game mode in the
picture menu. If you display the TV menu in Game mode, the screen shakes slightly.
Game Mode is not available in TV mode.
If Game Mode is On :
Picture Mode is automatically changed to Standard and users cannot change the mode.Sound Mode in the Sound menu is deactivated. Adjust the sound using the equalizer.The Reset Sound function is activated. Selecting the Reset function after setting the
equalizer resets the equalizer setting to the factory defaults.
Return
English - 26
English - 27

Wall- mount adjustment (Sold separately) (PS-50P96FDR)

Once the wall mount is installed, the position of your TV can be easily adjustable.
Rear Panel Auto Wall-Mount
Serial Cable(1P to 1P)(Not supplied)
Entering the menu 1 Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the ENTER/OK button.
2 Press the ▲ or ▼ button to select Wall-Mount Adjustment,
then press the ENTER/OK button.
T V
More Wall­Energy Saving : Off
HDMI Black Level : Normal PIP
Screen Burn Protection
3 Adjust to the desired position using the ▲/▼/◄/► buttons.
Press the EXIT button to exit.
If you press an arrow button when no OSD is displayed on the
TV screen, the Adjustment screen appears. When you turn the power off, your TV moves to the initial
installation position.When you turn the power on, your TV
Wall-Mount Adjustment
Position1
moves to the last remembered position you adjusted.
Using the remote Control Buttons
Button Operations
Wall-mount angle adjustment
Reset
Remembering the position and
(Red) (Green) (Yellow)
moving to the remembered position
For installation, refer to the Installation Manual provided.
For product installation and the installation and moving of the wall mount, make sure to consult a
specialized installation company. This installation manual is to be used when attaching the wall mount to a wall. When attaching to
other building materials, please contact your nearest dealer.
Tilt Up, Tilt Down, Move right, Move left
Moves to the initial installation position
Remembers 3 positions with the Red, Green and Yellow buttons. Moves to the remembered position using these 3 colour buttons.
Position
Adjust Centre
Setup
Mount Adjustment
Move
Enter
Return
1 2 3
INFO
Exit

Viewing the Picture in Picture (PIP)

You can display a sub picture within the main picture. In this way you can watch TV programme or monitor the video input from any connected devices.
1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Setup, then press the
ENTER/OK button.
T V
More
Mount Adjustment
Wall-
Energy Saving : Off
HDMI Black Level : Normal
PIP Screen Burn Protection
3 Press the ▲ or ▼ button to select PIP, then press the ENTER/
OK button.
4 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available options:
PIP(On/Off), Source, Size, Position,
T V
Programme
5 When you are satisfied with your setting, press the ENTER/OK
button.
Move
PIP : On Source : TV Size :
Position :
Programme : P 1
6 Press the EXIT button to exit.
PIP: On/Off
You can activate or deactivate the PIP function.
You can select these options simply by pressing the PIP
button on the remote control.
Move
Source: TV/Ext.1/Ext.2/AV
You can select a source of the sub-picture.
Size:
/
/
You can select a size of the sub-picture.
If main picture is in PC and Component mode, Size is not
available.
Position:
/
/
/
You can select a position of the sub-picture.
Programme
You can select a channel of the sub-picture only when the Source is set to TV.
Table of PIP Settings
X - This PIP combination is not available. O - This PIP combination is available.
Sub
Main
TV analog Ext.1 Ext.2 AV S-Video Component HDMI PC TV digital
Component O O O O X X X X X HDMI O O O O X X X X X PC O O O O X X X X X
Setup
Enter
PIP
Enter
Return
Return
English - 28
English - 29

Screen Burn Protection

To reduce the possibility of screen burn, this unit is equipped with screen burn prevention technology. This technology enables you to set picture movement up/down (Vertical Line) and side to side (Horizontal Dot). The Time setting allows you to programme the time between movement of the picture in minutes.
T V
More
Mount Adjustment
Wall-
Energy Saving : Off
HDMI Black Level : Normal PIP
Screen Burn Protection
Setup
1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Setup, then press the
ENTER/OK button.
3 Press the ▲ or ▼ button to select Screen Burn Protection,
then press the ENTER/OK button.
T V
4 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available options:
Pixel Shift, All White, Signal Pattern, Side
Move
Pixel Shift All White Signal Pattern Side Gray :
Enter
Screen Burn Protection
Dark
Return
Gray
5 When you are satisfied with your setting, press the ENTER/OK
button.
6 Press the EXIT button to exit. Pixel Shift: Using this function, you can minutely move pixels
on the PDP in horizontal or vertical direction to minimize after image on the screen.
− Set Pixel Shift to On by pressing the ▲ or ▼ button, then press the ENTER/OK button.
T V
Move
Pixel Shift
Enter
2 2 min
Pixel Shift : On Horizontal Dot : 2 Vertical Line : Time :
Return
− Select the required option by pressing the ▲ or ▼ button, then press the ENTER/OK button.
Available options: Horizontal Dot, Vertical Line, Time
Optimum condition for pixel shift;
PC
TV/Ext/AV/S-Video/
Component/HDMI/DTV
Move
Enter
Return
Horizontal Dot 1 2
Vertical Line
1 2
Time (minute) 2 min 2 min
The Pixel Shift value may differ depending on the monitor size (inches) and mode.
All White: This function helps remove after images on the screen by changing the colour of pixels to
white. Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image on the screen for a long time.
Signal Pattern: This function helps remove after images on the screen by moving all the pixels on
the PDP according to a pattern. Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image on the screen for a long time.
Side Gray: When you watch TV with the screen ratio of 4:3, the screen is prevented from any
damage by adjusting the white balance on both extreme left and right sides.
Dark: When you set the screen ratio to 4:3, it darkens the left and right sides. Light: When you set the screen ratio to 4:3, it brightens the left and right sides.
To remove after images on the screen, use either All White or Signal Pattern function. Although
both of the two functions remove after images on the screen, Signal Pattern is more effective. The after image removal function has to be executed for a long time (approximately 1 hour) to
effectively remove after images on the screen. If after image is not improved after the execution of the function, repeat the function again.
Press any button on the remote control to cancel this feature.

Setting up Your PC Software (Based on Windows XP)

The Windows display-settings for a typical computer are shown below. But the actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card. But even if your actual screens look different, the same, basic set-up information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
1 Right click the mouse on the Windows Desktop, then click on
Properties. The Display Properties will be displayed.
2 Click on Settings tab, then set the Display Mode with
reference to the Display Modes Table. You do not need to change the Colours settings.
3 Click on Advanced. A new settings dialog box will be
displayed.
4 Click on the Monitor tab, then set the Screen refresh rate with reference to the Display Modes
Table. Set the Vertical Frequency and Horizontal Frequency individually if you can do so instead of setting the Screen refresh rate.
5 Click on OK to close the window, then Click on OK button to the Display Properties window.
Automatic rebooting may commence at this moment.
English - 30
+ 90 hidden pages