Samsung PS50B850Y1W, PS58B850Y1W User Manual [uk]

удивительные возможности

Благодарим за приобретение продукта компании Samsung. Для получения более полного обслуживания зарегистрируйте свое устройство по адресу:

www.samsung.ru/club/registration

Модель_______Серийный номер_________

Связывайтесь с SAMSUNG по всему миру

Если у вас есть предложения или вопросы по продуктам Samsung, связывайтесь с информационным центром Samsung.

Country

Customer Care Centre 

Web Site

RUSSIA 8-800-555-55-55 www.samsung.ru

UKRAINE 8-800-502-0000

www.samsung/ua

www.samsung.com/ua_ru

Плазменный

телевизор

руководство пользователя

BN68-02334G-01

User Instructions

Screen Image retention 

Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.

Height 

The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height so do not install and operate there.

Heat on the top of the PDP TV 

The top side of the product may be hot after long period of use as heat dissipates from the panel through the vent hole in the upper part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children should be prevented from touching the upper part of the product.

The product is making a ‘cracking’ noise. 

A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as temperature or humidity. This is normal and not a defect of the unit.

Cell Defects 

The PDP uses a panel consisting of 2,360,000(HD-level) to 6,221,000(FHD-level) pixels which require sophisticated technology to produce. However, there may be few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product.

Avoid operating the TV at temperatures below 5°C(41°F) 

A still image displayed too long may cause permanent damage to the PDP Panel. 

Watching the PDP TV in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and centre of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause similar effect to the screen. Damages caused by the above effect are not covered by the Warranty.

Afterimage on the Screen. 

Displaying still images from Video games and PC for longer than a certain period of time may produce partial afterimages. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.

Warranty 

Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty. -

Installation 

Be sure to contact an authorized service centre, when installing your set in a location with heavy dust, high or low temperatures, high humidity, chemical substance and where it operates continually such as the airport, the train station etc. Failure to do so may cause a serious damage to your set.

Digital TV Notice

1. Functionalities related to Digital TV(DVB) are only available in countries/areas where DVB-T (MPEG2 and MPEG4 AVC)

digital terrestrial signals are broadcasted or where you have access to a compatible DVB-C(MPEG2 and MPEG4 AAC) cable-TV service. Please check with your local dealer the possibility to receive DVB-T or DVB-C signal.

2. DVB-T is the DVB European consortium standard for the broadcast transmission of digital terrestrial television and DVB-C

is that for the broadcast transmission of digital TV over cable. However, some differentiated features like EPG (Electric Program Guide), VOD (Video on Demand) and so on, are not

included in this specication. So, they cannot be supported at this moment.

3. Although this TV set meets the latest DVB-T and DVB-C standards[August,2008], the compatibility with future DVB-T digital

terrestrial and DVB-C digital cable broadcasts cannot be guaranteed.

4. Some cable-TV providers may charge an additional fee for such a service and you may be required to agree to terms and

conditions of their business.

5. Some Digital TV functions might be unavailable in some countries or regions and DVB-C might not work correctly with all

providers.

6. For more information, please contact your local Samsung customer care centre.

Contact SAMSUNG WORLDWIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre. (See back cover for more informations.)

Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance. Product design and specications may be changed without notice in order to enhance product performance.

English - 2

English - 3

Contents

English

Connecting and Preparing Your TV

Checking Parts ■ ..........................................................................4

Using the Stand-Base ■ ..............................................................4

Viewing the Control Panel ■ .........................................................5

Viewing the Connection Panel ■ ................................................... 6

Remote Control ■ .........................................................................8

Installing Batteries in the Remote Control ■ .................................8

Using the Remote Control Backlight Buttons ■ ............................ 9

Switching On and Off ■ ................................................................. 9

Placing Your Television in Standby Mode ■ .................................. 9

Viewing the Display ■ ...................................................................9

Viewing the Menus ■ ..................................................................10

Using the TOOLS Button ■ ........................................................ 10

Plug & Play Feature ■ ................................................................ 11

Channel Control

Storing Channels ■ ................................................................... 12

Managing Channels ■ ................................................................14

Picture Control

Changing the Picture Settings ■ .................................................16

Setting up the TV with your PC ■ ...............................................19

PC Display ■ ...............................................................................20

Sound Control

Changing the Sound Setting ■ ...................................................21

Selecting the Sound Mode ■ ...................................................... 22

Function Description

Setting the Time ■ ...................................................................... 23

Conguring the Setup Menu ■ ....................................................24

Viewing the Picture in Picture (PIP) ■ ......................................... 26

Support / Input

Supported Program ■ .................................................................27

Source List / Edit Name ■ ...........................................................28

Media Play-DLNA

Setting the DLNA Network ■ .......................................................46

Installing the DLNA Application ■ ...............................................46

Using the DLNA Application ■ ....................................................48

Using the DLNA Function ■ ........................................................ 51

About Anynet+

Connecting Anynet ■ Setting Up Anynet ■ Switching between Anynet ■

Recording ■ ................................................................................55

Listening through a Receiver ■ ...................................................55

Troubleshooting for Anynet ■

Devices ................................................... 52

.................................................................53

Devices .......................................54

...................................................56

Content Library

Activating the Content Library ■ ................................................. 57

Using the Content Library ■ ........................................................ 58

Home Network Centre

Home Network Centre ■ ............................................................. 59

Setting Up the Home Network Centre ■ .....................................60

Using the Message Function ■ ................................................... 61

Using the Media Function ■ ........................................................ 62

Recommendations for Use

Teletext Feature ■ .......................................................................63

Wall Mount Kit Specications (VESA) ■ .....................................64

Preparing before installing Wall- Mount ■ ...................................65

Securing the TV to the Wall ■ ..................................................... 65

Securing the Installation Space ■ ............................................... 66

How to assemble the Stand-Base ■

(depending on the model) .......................................................66

Assembling the Cables ■ ............................................................67

Troubleshooting ■ .......................................................................68

Specications ■ ..........................................................................71

Software License ■ ..................................................................... 72

Network

Network Connection ■ ................................................................29

Network Setup ■ ......................................................................... 31

Media Play

Connecting a USB Device ■ ....................................................... 34

Using the Media Play Function ■ ................................................35

Using and Sorting Photo List ■ ................................................... 36

Viewing a Photo or Slide Show ■ ..............................................37

Using and Sorting the Music List ■ ............................................. 39

Playing a Music ■ ......................................................................40

Using and Sorting the Movie List ■ .............................................41

Playing a Movie File ■ ...............................................................42

Picture / Music Settings Using Media Play ■ .............................. 44

Using the Setup Menu ■ ............................................................. 45

Symbol Press Note One-Touch Button TOOLS

N O T

Connecting and Preparing Your TV

Checking Parts

Owner’s Instructions Remote Control/

Cover-Bottom

(PS50B850 only)

AV Cable Component Cable Holder-Wire Cable

Ferrite Core N

The ferrite cores are used to shield the cables from interference. When connecting a cable, open the ferrite core and clip it around the cable near the plug as

shown in the gure.

AAA Batteries (2ea)

Screws (5ea)

(PS50B850 only)

Program CD

Cover-Bottom/Screw

(PS58B850 only)

(Refer to page 67)

Cloth-Clean Holder-Ring (4ea)

Holder-Wire stand (Refer to page 67)

Ferrite Core (4ea)

Power Cord (2ea) LAN Cable

(Refer to page 65)

Holder-Wire (3ea) (Refer to page 67)

(1ea)

Warranty Card/

Safety Guide Manual

(Not available in all

locations)

Ext Cable

HDMI Cable

(1ea)

Using the Stand-Base

Two or more people should carry the PDP. Never lay the PDP on the oor N

because of possible damage to the screen. Always keep the PDP upright. The PDP can rotate 20 degrees in right and left directions.

English - 4

-20° ~ 20°

English - 5

Viewing the Control Panel

The product colour and shape may vary depending on the model. N

Front Panel buttons

Touch each button to operate.

REMOTE CONTROL SENSOR

Aim the remote control towards this spot on the TV.

SOURCE

Toggles between all the available input sources (TV, AV, Component, PC, HDMI1/DVI, HDMI2, HDMI3, HDMI4, USB).

In the on-screen menu, use this button as you would use

the ENTERE button on the remote control.

Press to see an on-screen menu of your TV’s features.

+ VOL –

Press to increase or decrease the volume. In the on-screen menu, use the + VOL – buttons as you would use the

◄ and ► buttons on the remote control.

Press to change channels. In the on-screen menu, use the buttons as you would use the ▲ and ▼ buttons on the remote control. You can use button to turn on the TV without the remote control.

POWER INDICATOR

Blinks and turns off when the power is on and lights up in stand-by mode.

(

POWER)

Press to turn the TV on and off.

SPEAKERS

Viewing the Connection Panel



TV Rear Panel

4 53

987

Cable Television

Network

The product colour and shape may vary depending on the model.

Whenever you connect an audio or video system to your set, ensure that all elements are switched off.

When connecting an external device, match the colour of the connection terminal to the cable.

English - 6

English - 7

For best cable connection to this product, be sure to use N cables with a maximum thickness as below.

Below 40 inch model: • Max 0.47inch (12mm)

40 inch and above model: • Max 0.55inch (14mm)

COMMON INTERFACE Slot

Insert CI(CI+) (Common Interface) card into the slot. (refer to page 24)

When not inserting - CI(CI+) CARD in some channels, Scramble Signal is displayed on the screen.

The pairing information containing a telephone number, CI(CI+) CARD ID, Host ID, and other information will be displayed in about 2~3 minutes. If an error message is displayed, please contact your service provider.

When the channel information conguration has nished, the message Updating Completed is displayed, indicating that the channel list is now updated.

Insert the CI(CI+)-Card in the direction marked on it.

CAM is not supported in some countries and N regions,check with your authorized dealer.

The CI+ function is only applicable to PS********P model.

If you have some problems, please contact to service provider

USB 1 (HDD), USB 2

Connect a USB mass storage device to view photo les (JPEG), play audio les (MP3) and movie les. You can connect to SAMSUNG’s network wirelessly.

The USB 1 (HDD) port is also used as the HDD.

HDD (Hard disk drive) is device which stores digitally encoded data

AV IN (AUDIO L/R / VIDEO)

Video and audio inputs for external devices, such as a camcorder or VCR.

COMPONENT IN

Audio (AUDIO L/R) and video (Y/P

PC IN / PC/DVI AUDIO IN

B/PR) inputs for Component.

Connect to the video and audio output jack on your PC.

HDMI IN 1 (DVI), 2, 3, 4

No additional Audio connection is needed for an HDMI to HDMI connection.

Whenusing an HDMI/DVI cable connection, you must use -

the HDMI IN 1 (DVI) jack.

What is HDMI?

High Definition Multimedia interface - allows the

transmission of high denition digital video data and

multiple channels of digital audio.

The HDMI/DVI terminal supports DVI connection to an extended device with the appropriate cable (not supplied). The difference between HDMI and DVI is that the HDMI device is smaller in size, has the HDCP (High Bandwidth Digital Copy Protection) coding feature installed, and supports multi - channel digital audio.

We recommend using HDMI cables no more than 14mm

wide.

PC/DVI AUDIO IN

DVI audio outputs for external devices.

Supported modes for HDMI/DVI and Component

POWER IN

Connect the supplied power cord.

LAN

Connect a LAN cable to this port to connect to the Network (SAMSUNG's Internet@TV Service).

ANT IN

75Ω Coaxial connector for Aerial/Cable Network.

6 EXT (RGB)

Inputs or outputs for external devices, such as VCR, DVD, video game device or video disc players.

In EXT mode, DTV Out only supports MPEG SD Video

and Audio. In EXT Mode, Game mode is not available

Input/Output Specification

Connector

Video Audio(L/R) RGB Video + Audio(L/R)

EXT ✔ ✔ ✔

Input Output

Only TV or DTV output

is available.

HDMI/DVI 50Hz X X X O O O O HDMI/DVI 60Hz X O X X O O O

Component O O O O O O O

480i 480p 576i 576p 720p 1080i 1080p

! SERVICE

Connector for service.

DIGITAL AUDIO OUT (OPTICAL)

Connect to a Digital Audio Component.

Remote Control

You can use the remote control up to a distance of about 23 feet from the TV.

The performance of the remote control may be affected by bright light.

POWER button

(turns the TV on and off)

Selects the TV mode directly.

Number buttons for direct channel

access.

Press to switch to your favorite

channels.

Use to see information on the current

broadcast.

Displays the main on-screen menu.

Use to quickly select frequently used

functions.

Use to select on-screen menu items

and change menu values.

This function enables you to view

Internet@TV.

Use these buttons in the Channel list,

Media Play, and Internet@TV, etc.

Available source selection

Volume increase

Volume decrease

Use to display Channel Lists on the

screen.

Turn the audio description function on

or off.

Use these buttons in the Anynet+ and

Media Play.

Press to backlight the buttons on the

remote. This function is convenient for using at night or when the room is

dark. (Using the remote control with

the ON/OFF( ) light button set to On will reduce the battery usage time.)

Previous channel

Electronic Program Guide (EPG)

(

display

Returns to the previous menu.

)

Exit the on-screen menu.

Next channel

Previous channel

Temporary sound switch-off.

This function enables you to view

Content Library.

This function enables you to view and

play photo, music and movie les from

an external device.

Digital subtitle display

Teletext Functions

Exit from the teletext display

(depending on the model)

Teletext reveal

Teletext index

Teletext size

Fastext topic selection

Teletext mode selection (LIST/FLOF)

Teletext display/mix both

teletext information and the normal broadcast

Teletext store

Teletext sub page

Teletext hold

)

Teletext cancel

P :Teletext next page

P :Teletext previous page

Installing Batteries in the Remote Control

1. Lift the cover at the back of the remote control upward as shown in the gure.

2. Install two AAA size batteries.

Make sure to match the ‘+’ and ‘–’ ends of the batteries with the diagram inside

the compartment.

3. Close the cover.

Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a long time.

If the remote control doesn’t work, check the following N

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power outage or is the power cord unplugged?

5. Is there a special uorescent light or neon sign nearby?

English - 8

English - 9

Using the Remote Control Backlight Buttons

Use this feature in dark surroundings and when you are unable to see the remote control buttons clearly.

1. Press the ON/OFF(

When

N ON, the button backlight is turned on for a moment.

Pressing a remote co

N ntrol button when the remote control is on turns the button backlight on for a moment.

) light button

Switching On and Off

The mains lead is attached to the rear of your set.

1. Plug the mains lead into an appropriate socket.

The standby indicator lights up on your set.

2. Press the POWERP button on your set.

You also can press the

N POWER

turn the TV on. The programme that you were watching last is reselected automatically.

3. Press the numeric button (0~9) or channel up / down (< / >) button on the remote control or < > button on your set.

When you switch the set on for the very rst time, you will be asked to choose language in which the menus are to be displayed.

4. To switch your set off, press the POWERP button again.

button or the TV button on the remote control to

Placing Your Television in Standby Mode

Your set can be placed in standby mode in order to reduce the power consumption. The standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).

1. Press the POWERP button on the remote control.

The screen is turned off and a red standby indicator appears on your set.

2. To switch your set back on, simply press the POWERP, numeric buttons (0~9), TV button or channel up / down (< / >) button

again.

Do not leave your set in standby mode for long periods of time (when you are away on holiday, for example). It is best to unplug

the set from the mains and aerial.

Viewing the Display

The display identifies the current channel and the status of certain audio-video settings.

O INFO button to viewing the information.

Press the

Press the INFO button on the remote control. The TV will display the channel, the type of sound, and the status of certain picture and sound settings.

▲, ▼: You can view other channel’s information. If you want to move to the currently • selected channel, press ENTERE button.

◄, ►: You can view the desired program’s information at the current channel. •

Press the

N INFO button once more or wait approximately 10 seconds and the display

disappears automatically.

Viewing the Menus

1. With the power on, press the MENU button. The main menu appears on the screen. The menu’s left side has icons: Picture, Sound, Channel, Setup, Input, Application, Support.

2. Press the ▲ or ▼ button to select one of the icons. Then press the ENTER button to access the icon’s sub-menu.

3. Press the EXIT button to exit.

The on-screen menus disappear from the screen after about one minute.

Using the TOOLS Button

You can use the TOOLS button to select your frequently used functions quickly and easily. The Tools menu changes depending on which external input mode you are viewing.

1. Press the TOOLS button. The Tools menu will appear.

2. Press the ▲ or ▼ button to select a menu, then press the ENTER

3. Press the ▲ / ▼ / ◄ / ► / ENTER

buttons to display, change, or use the selected

items. For a more detailed description of each function, refer to the corresponding page.

Anynet •

(HDMI-CEC), see page 53

Picture Size, see page 17 • Picture Mode, see page 16 •

Sound Mode, see page 21 • Sleep Timer, see page 23 • SRS TS HD, see page • 21 Energy Saving, see page 26 •

Dual l ll, see page 22 • Add to Favourite (or Delete from Favourite), see page 14 • PIP, see page 26 • Auto Adjustment, see page 19 •

button.

Picture

Mode

Cell Light : 4

Contrast : 95

Brightness : 45

Sharpness : 50

Colour : 50

Tint (G/R) : G50/R50

Advanced Settings

Picture Size : Auto Wide Picture Mode : Standard Sound Mode : Custom Sleep Timer : Off SRS TS HD : Off Energy Saving : Off

Dual l ll : Mono Add to Favourite

Anynet+ (HDMI-CEC)

Standard

Tools

Move E Ent er e Exit

English - 10

English - 11

Plug & Play Feature

When the TV is initially powered on, basic settings proceed automatically and subsequently.

The Screen Saver is activated if there is no remote control key input for longer than 1 minute while Plug & Play is running. The Screen Saver is activated if there is no operating signal for longer than 15 minutes. N

If you accidentally select the wrong country for your TV, the characters on the screen may be wrongly displayed. N

1. Press the POWER button on the remote control. Select the OSD Language. menu

is automatically displayed. Select the appropriate language by pressing the ▲ or ▼

button. Press the ENTERE button to conrm your choice.

2. Press the ◄ or ► button to select Store Demo or Home Use, then press the ENTER

button.

We recommend setting the TV to

N Home Use mode for the best picture in your

Select the OSD Language.

Language :

home environment.

Store Demo

N mode is only intended for use in retail environments.

If the unit is accidentally set to

N Store Demo mode and you want to return to Home Use (Standard): Press the Volume button on

the TV. When the volume OSD is displayed, press and hold the MENU button on the TV for 5 seconds.

3. Press the ENTER

button. Select the appropriate country by pressing the ▲ or ▼ button. Press the ENTERE button to conrm

your choice.

4. Press the ▲ or ▼ button to memorize the channels of the selected connection, then press the ENTER

Air • : Air antenna signal. Cable • : Cable antenna signal.

5. Press the ▲ or ▼ button to select the Antenna source to memorize. Press the ENTER

button to select Start.

Digital & Analogue • : Digital and Analogue channels. Digital • : Digital channels. Analogue • : Analogue channels.

The channel search will start and end automatically.

6. The message Set the Clock Mode. is displayed. Press the ENTERE button. Press the ▲ or ▼ button to select Auto, then press the ENTERE button.

If you select

N Manual, Set current date and time is displayed. (For a more detailed description of Manual, refer to page 23)

If you have received a digital signal, the time will be set automatically.

7. The brief instruction on How to get the best performance from your new HDTV is displayed. Press the ENTERE button.

This menu is available

N HD Connection Guide in the Support menu.

You can change previous or next page by pressing the

N ◄ / ► button.

8. The message Enjoy your TV. is displayed.

If you want to view the TV immediately, select the

N Watch TV.

If you want to view the

N See Product Guide, press the ENTER

button.

Plug & Play

button.

Nederlands

English

Eesti

▲

▼

E Enter

If you want to reset this feature...

1. Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER

2. Press the ENTER

button.

button again to select Plug & Play.

3. Enter your 4 digit PIN number. The default PIN number of a new TV set is ‘0-0-0-0’.

If you want to change PIN(Personal Identication Number), refer to page 25.

The N Plug & Play feature is only available in the TV mode.

Setup

Plug & Play ►

Menu Language : English

Time

Broadcast

Security Network

General

Channel Control

Storing Channels

Country

❑

Digital Channel  : You can change the country for digital channels.

 : You can change the country for analogue channels.

Analogue Channel

The PIN number input screen appears. Enter your 4 digit PIN number. N

Auto Store

❑

Scans for all channels with active broadcast stations (and availability depends on your country) and stores them in the TV's memory.

You set the TV to memorize the channels of the selected connection.

Air • : Air antenna signal. Cable • : Cable antenna signal.

You can select the antenna source to memorize.

Digital & Analogue • : Digital and Analogue channels. Digital • : Digital channels. Analogue • : Analogue channels.

N Cable,

When selecting Search Mode • : Displays the search mode. (Quick)

- Network ID: Displays the network identication code.

- Frequency: Displays the frequency for the channel.

- Modulation: Displays available modulation values.

- Symbol Rate: Displays available symbol rates. Search Mode • : Displays the search mode.(Full, Network)

- Start Frequency: Displays the frequency start values.

- End Frequency: Displays the frequency stop values.

- Modulation: Displays available modulation values.

- Symbol Rate : Displays available symbol rates.

If you want to stop

N Auto Store, press the ENTER

Select Yes by pressing the ◄ or ► button, then press the ENTER

Manual Store

❑

Scans for a channel manually and stores it in the TV’s memory.

Digital Channel  (Digital)

Digital Channel is only available in DTV mode. N

Channel • : Set the Channel number using the ▲, ▼ or number (0~9) buttons. Frequency • : Set the frequency using the number (0~9) buttons. Bandwidth • : Set the bandwidth using the ▲ or ▼ buttons.

When it has nished, channels are updated in the channel list.

Analogue Channel 

Manual store for analogue channel.

Programme • (Programme number to be assigned to a channel): Sets the programme number using the ▲, ▼ or number (0~9) buttons.

Colour System → Auto / PAL / SECAM / NTSC 4.43 • : Sets the colour system value using the ▲ or ▼ button. Sound System • → BG / DK / I / L : Sets the sound system value using the ▲ or ▼ button. Channel • (When you know the number of the channel to be stored): Press the ▲ or ▼ button to select C (Air channel) or S

(Cable channel). Press the ► button, then press the ▲, ▼ or number (0~9) buttons to select the required number.

If there is abnormal sound or no sound, reselect the sound standard required.

Search • (When you do not know the channel numbers): Press the ▲ or ▼ button to start the search. The tuner scans the frequency range until the rst channel or the channel that you selected is received on the screen.

Store • (When you store the channel and associated programme number): Set to OK by pressing the ENTER

Channel mode

- C (Air channel mode):

You can select a channel by entering the assigned number to each air broadcasting station in this mode

- S (Cable channel mode): You can select a channel by entering the assigned number for each cable channel in this mode.

button. The Stop Auto Store? message will be displayed.

button.

Channel

Country ►

Auto Store Manual Store Cable Search Option

Full Guide

Mini Guide

Default Guide : Full Guide

Channel List

button.

English - 12

English - 13

Cable Search Option

❑

You can set additional search options such as frequency and symbol rate for cable network searching. (Depending on the each country)

Freq.Start • : Displays the frequency start values. Freq.Stop • : Displays the frequency stop values. Modulation • : Displays available modulation values. Symbol Rate • : Displays available symbol rates.

If the

N Freq.Start value is bigger than Freq.Stop value, the warning message is displayed.

Full Guide / Mini Guide

❑

The EPG (Electronic Programme Guide) information is provided by the broadcasters. Programme entries may appear blank or out of date as a result of the information broadcast on a given channel. The display will dynamically update as soon as new information becomes available.

Full Guide • : Displays the programme information as time ordered one hour segments. One hours of programme information is displayed which may be scrolled forwards or backwards in time.

Mini Guide • : The information of each programme is displayed by each line on the current channel Mini Guide screen from the current programme onwards according to the programme starting time order.

Default Guide

❑

Mini Guide / Full Guide  You can decide whether to display either the Mini Guide or the Full Guide when the

GUIDE button on the remote control is pressed.

You can also display the guide menu simply by pressing the

O GUIDE button.

Full Guide

Mini Guide

Channel

Default Guide : Full Guide ►

Channel List

Channel Mode : Added Ch.

Fine Tune

Using the Full / Mini Guide

Full Guide

900 f tn 901 ITV Play

902 Kerrang!

903 Kiss 903 oneword

903 Smash Hits!

▼

DTV Cable 900 f tn 2:10 Tue 1 Jun

Freshmen On Campus 2:00 - 2:30

No Detailed Information

Today 2:00 - 3:00 3:00 - 4:00

Freshmen O..

Street Hypn..

Mint Extra

Loaded

Fresh 40 with Dynamite MC The Distillery

Smash Hits! Sunday

Watch Information

▲ / ▼ / ◄ / ►

ENTER

No Information

Kisstory

No Information



Mini Guide



Page

+24 Hours Exit

Select a programme by pressing the ▲/▼/◄/►/ENTERE button.

RED Toggle between the Mini Guide or Full Guide.

GREEN Full Guide: Scroll backwards quickly (-24 hours).

YELLOW Full Guide: Scroll forwards quickly (+24 hours).

BLUE Exit the guide.

INFO INFO button for the detailed information.

Channel Mode

❑

When the press the P (</>) button, Channels will be switched within the selected channel list.

Added Ch.: 

Favourite Ch.: 

Channels will be switched within the memorized channel list.

Channels will be switched within the favourite channel list.

Mini Guide DTV Cable 900 f tn

2:00 2:30

▼

5:00

Freshmen On Campus

Street Hypnosis

Booze Britain

Watch Information

Page



Full Guide Exit

Fine Tune ❑(Analogue channel only)

If the reception is clear, you do not have to ne tune the channel, as this is done automatically during the search and store operation. If the signal is weak or distorted, you may have to ne tune the channel manually.

Fine tuned channels that have been saved are marked with an asterisk

N * on the right-hand side of the channel number in the

channel banner.

If you do not store the ne-tuned channel in memory, adjustments are not saved.

To reset the ne-tuning, select N Reset by pressing the ▼ button and then press the ENTER

button.

Managing Channels

Using this menu, you can Add / Delete or set Favourite channels and use the programme

guide for digital broadcasts.

N All Channels, Added Channels, Favourites, or Programmed

Select a channel in the screen by pressing the ▲ or ▼ buttons, and pressing the ENTERE button.

Then you can watch the selected channel.

All Channels • : Shows all currently available channels. Added Channels • : Shows all added channels. Favourites • : Shows all favourite channels. Programmed • : Shows all current reserved programmes.

Press the

O CH LIST button on the remote control to bring up the channel lists.

Using the Colour buttons with the Channel List

Red - (Channel Type): Toggle between your TV, Radio, Data/Other and All. Green - (Zoom): Enlarges or shrinks a channel number. Yellow - (Select): Selects multiple channel lists. T - TOOLS (Tools): Displays the Delete (or Add), Add to Favourite (or Delete from

Favourite), Lock (or Unlock), Timer Viewing, Edit Channel Name, Edit Channel Number, Sort, Select All (or Deselect All), or Auto Store menu.

(The Tools menus may differ depending on the situation.)

Channel Status Display Icons

A channel selected by pressing the

An Analogue channel.

A channel set as a Favourite.

♥

A locked channel.

yellow button.

A programme currently being

(

broadcast.

)

A reserved programme

Channel Lis ❑t Tools Menu (in All Channels / Added Channels / Favourites)

Press the N TOOLS button to use the Tools menu. The

N Tools menu items may differ depending on the channel status.

Add / Delete 

You can delete or add a channel to display the channels you want.

All deleted channels will be shown on

N All Channels menu.

A gray-coloured channel indicates the channel has been deleted.

The N Add menu only appears for deleted channels. You can also delete a channel to the

N Added Channels or Favourites menu in the

same manner.

Add to Favourite / Delete from Favourite 

You can set channels you watch frequently as favourites.

Press the TTOOLS button to display Tools menu. You can also add the favourite channel by selecting Tools → Add to Favourite (or Delete from Favourite).

Mini Guide

Default Guide : Full Guide

Channel

Channel List

Channel Mode : Added Ch.

Fine Tune

824 UKTV Gold

All Channels

825 UKTV style

1 C --

2 C A 3 ♥ C A 4 C A 5 C A 6 C A 7 C A 8 C

All



Channel Type Zoom Select

824 UKTV Gold

All Channels

825 UKTV style

1 C --

2 C A 3 C A 4 C A 5 C A 6 C A 7 C A 8 C

All



Channel Type Zoom Select

Delete

Add to Favourite

Lock

Timer Viewing

Edit Channel Name

Sort

Tools

Page

▼

Tools

Page

O FAV.CH button on the

To select the Favourite channels you have set up, press the remote control.

The “♥” symbol will be displayed and the channel will be set as a favourite.

All favourite channels will be shown on Favourite menu. N

English - 14

Continued...

English - 15

Lock / Unlock 

You can lock a channel so that the channel cannot be selected and viewed. This function is available only when the Child Lock is set to on. (see page 25)

The PIN number input screen appears. Enter your 4 digit PIN number.

The default PIN number of a new TV set is ‘0-0-0-0’. You can change the PIN, by selecting Change PIN from the menu. N

The “ N \” symbol will be displayed and the channel will be locked.

Timer Viewing 

If you reserve a programme you want to watch, the channel is automatically switched to the reserved channel in the Channel List; even when you are watching another channel. To reserve a programme set the current time rst. (See page 23)

Only memorized channels can be reserved.

You can set the channel, month, day, year, hour and minute directly by pressing the number buttons on the remote control. N Reserving a programme will be shown on N Programmed menu.

Digital Programme Guide and Viewing Reservation

When a digital channel is selected, and you press the ► button, the Programme Guide for the channel appears. You can reserve a programme according to the procedures described above.

Edit Channel Name  (Analogue channel only)

Channels can be labeled so that their call letters appear whenever the channel is selected.

The names of digital broadcasting channels are automatically assigned and cannot be labeled. N

Edit Channel Number  (Digital channel only)

You can also edit the channel number by pressing the number buttons on the remote control.

Sort  (Analogue channel only)

This operation allows you to change the programme numbers of the stored channels. This operation may be necessary after using the auto store.

Select All / Deselect All 

You can deselect or select all channels in the channel list.

You can perform the Add / Delete, Add to Favourites / Delete from Favourites, or Lock / Unlock function for multiple channels at

the same time. Select the required channels and press the yellow button to set all the selected channels at the same time.

The

N c mark appears to the left of the selected channels.

You can only select

N Deselect All when there is a selected channel.

Auto Store 

For further details on setting up options, refer to page 12. N If a channel is locked using the N Child Lock function, the PIN input window appears.

Channel List Tools Menu ( ❑in Programmed )

You can view, modify or delete a reservation. Press the

N TOOLS button to use the Tools menu.

Change Info • : Select to change a viewing reservation. Cancel Schedules • : Select to cancel a viewing reservation. Information • : Select to view a viewing reservation. (You can also change the reservation

information.) Select All / Deselect All • : Select or deselect all reserved programmes.

Programmed

1 / 1 / 2009

13:59 5 TV1 Quincy, M.E

18:59 2 TV3 The Equalizer

20:59 2 TV3 McMillan & Wife

21:59 2 TV3 M.Spillane’s mike Hammer

All



Zoom Select

Change Info

Cancel Schedules

Information

Select All

Tools Information

Picture Control

Changing the Picture Settings

Mode

❑

You can select the type of picture which best corresponds to your viewing requirements.

Dynamic / Standard / Eco / Movie 

Press the TTOOLS button to display Tools menu. You can also set the picture mode by selecting Tools → Picture Mode.

When in

N PC mode, Eco is not available.

Cell Light / Contrast / Brightness / Sharpness / Colour / Tint (G/R)

❑

Your television has several setting options that allow you to control the picture quality.

Cell Light • : Adjusts the pixel brightness. Contrast • : Adjusts the contrast level. Brightness • : Adjusts the brightness level. Sharpness • : Adjusts the sharpness. Colour • : Adjusts the colour saturation of the picture using the bar on the screen. Tint (G/R) • : Adjusts the colour tint of the picture.

When you make changes to

N Cell Light, Contrast, Brightness, Sharpness, Colour or Tint (G/R), the OSD will be adjusted

accordingly. The adjusted values are saved for each picture mode.

In Analogue N TV, Ext., AV modes of the PAL system, you cannot use the Tint Function. In

N PC mode, you can only make changes to Cell Light, Contrast and Brightness.

Each adjusted setting will be stored separately according to its input mode.

The energy consumed during use can be signicantly reduced if the level of brightness of the picture is reduced, and then this N

will reduce the overall running cost.

Advanced Settings

❑

You can adjust the advanced settings for your screen including the colour and contrast.

Advanced Settings

N is available in Standard or Movie mode.

N PC mode, you can only make changes to Dynamic Contrast, Gamma and

White Balance from among the Advanced Settings items.

Black Tone →  Off / Dark / Darker / Darkest

You can enhance the picture depth by adjusting the black colour density.

Dynamic Contrast →  Off / Low / Medium / High

You can adjust the screen contrast so that the optimal contrast is provided.

Gamma 

You can adjust the primary colour (Red, Green, Blue) Intensity.

Colour Space 

Colour Space is a colour matrix composed of red, green and blue colours. Select your favourite Colour Space to experience the

most natural colour.

Auto • : Automatically sets the colour range depending on the input video source. Native • : Sets the colour range wider than the that of the input video source. Custom • : Adjusts the colour range to suit your preference.

Customizing the Colour Space

- Adjusts the Colour range to suit your preference. Colour is available when Colour Space is set to Custom.

- Colour → Red / Green / Blue / Yellow / Cyan / Magenta

- Red / Green / Blue: You can adjust the RGB values for the selected colour.

- Reset: Resets the colour space to the default values.

Picture

Mode : Standard ►

Cell Light : 4

Contrast : 95

Brightness : 45

Sharpness : 50

Colour : 50

Tint (G/R) : G50/R50

Advanced Settings

Colour : 50

Tint (G/R) : G50/R50

Picture

Advanced Settings ►

Picture Options

Picture Reset

White Balance 

You can adjust the colour temperature for more natural picture colours.

R-Offset / G-Offset / B-Offset / R-Gain / G-Gain / B-Gain • : Changing the adjustment value will refresh the adjusted screen. Reset • : Resets the default white balance.

Continued...

English - 16

English - 17

Flesh Tone 

You can adjust the esh tone to be more or less red.

Changing the adjustment value will refresh the adjusted screen.

Edge Enhancement →  Off / On

You can emphasize object boundaries in the picture.

xvYCC → Off / On 

Setting the xvYCC mode to on increases detail and colour space when watching movies from an external device (i.e. DVD player).

xvYCC

N is available when the picture mode is set to Movie, and the external input is set to HDMI or Component mode.

This function may not be supported depending on your external device.

Picture Options

❑

You can customize the additional picture settings to suit your preference.

N PC mode, you can only make changes to the Colour Tone, Size and Screen

Burn Protection from among the items in Picture Options.

Colour Tone →  Cool / Normal / Warm1 / Warm2 / Warm3

You can select the most comfortable colour tone to your eyes.

The adjusted values are stored according to the selected

N Picture mode.

Warm1, Warm2,

N or Warm3 is only activated when the picture mode is Movie.

Size → Auto Wide / 16:9 / Wide Zoom / Zoom / 4:3 / Screen Fit 

You can select the picture size which best corresponds to your viewing requirements.

Auto Wide • : Sets the picture in Auto Wide format. 16:9 • : Sets the picture to the 16:9 aspect ratio. Wide Zoom • : Select this menu to view 4:3 aspect ratio pictures over a 16:9 aspect ratio TV by stretching the 4:3 picture

vertically.

Zoom • : Stretches the 16:9 aspect ratio picture vertically. 4:3 • : Sets the picture to the 4:3 aspect ratio. Screen Fit • : Displays the full native HD signal that cannot be viewed using a normal TV.

Depending on the input source, the picture size options may vary.

The items available may differ depending on the selected mode.

In NPC Mode, only 16:9 and 4:3 mode can be adjusted. When Double

Settings can be adjusted and stored for each external device you have connected to an input of the TV.

Temporary image retention may occur when viewing a static image on the set for more than two hours.

Wide Zoom N: Press the ► button to select Position, then press the ENTERE button.

Press the ▲ or ▼ button to move the screen up / down. Then press the ENTERE button.

Zoom

picture up and down. Then press the ENTERE button. Press the ► button to select Size, then press the ENTERE button.

Press the ▲ or ▼ button to magnify or reduce the picture size in the vertical direction. Then press the ENTERE button.

After selecting

the ◄ or ►button. Use the ▲, ▼, ◄ or ► button to move the picture.

Reset

If you use the

function.

( , ) mode has been set in PIP, the Picture Size cannot be set.

: Press the ► button to select Position, then press the ENTERE button. Press the ▲ or ▼ button to move the

Screen Fit in HDMI (1080i / 1080p) or Component (1080i / 1080p) mode: Select Position by pressing

: Press the ◄ or ► button to select Reset, then press the ENTERE button. You can initialize the setting.

Screen Fit function with HDMI 720p input, 1 line will be cut at the top, bottom, left and right as in the overscan

Tint (G/R) : G50/R50

Advanced Settings

Picture

Picture Options ►

Picture Reset

Screen Mode  → 16:9 / Wide Zoom / Zoom / 4:3

When setting the picture size to Auto Wide in a 16:9 wide TV, you can determine the picture size you want to see the 4:3 WSS (Wide Screen Service) image or nothing. Each individual European country requires different picture size so this function is

intended for users to select it.

This function is available in

N Auto Wide mode.

This function is not available in

N PC, Component or HDMI mode.

Digital NR  → Off / Low / Medium / High / Auto

If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction feature to help reduce any static

and ghosting that may appear on the screen.

When the signal is weak, select one of the other options until the best picture is displayed.

HDMI Black Level  → Normal / Low

You can directly select the black level on the screen to adjust the screen depth.

This function is active only when the external input connects to HDMI (RGB signals).

Continued...



1080 Full HD Motion Demo → Off / On

Samsung's new generation PDP panels deliver stunning Full HD motion clarity when viewing fast action sports, movies, and games.

This function is not available in PC, Game or Media Play mode.

Film Mode 

You can optimize the picture mode for watching movies.

Off • : Turn the Film Mode function off. Auto1 • : Automatically adjusts the picture for the best quality when watching a lm. Auto2 • : Automatically optimizes the video text when watching a lm. Cinema Smooth • : Offers the ultimate cinema experience.

Film mode is supported in TV, Video, Component(480i / 1080i) and HDMI(1080i).

Real 100Hz Demo → Off / On 

You can get a clear distinction between Real 100Hz and 50Hz, especially when watching fast moving scenes. Therefore, when seeing slow moving scenes, you will not be able to distinguish between Real 100Hz and 50Hz. Demo 100Hz works only with 50Hz signal. Real 100Hz demo mode is provided for shop demonstration with special pictures.



Blue Only Mode → Off / On

This function is for AV device measurement experts. This function displays the blue signal only by removing the red and green signals from the video signal so as to provide a Blue Filter effect that is used to adjust the Colour and Tint of video equipment such as DVD players, Home Theaters, etc.

Blue Only Mode

N is available when the picture mode is set to Movie or Standard.

Screen Burn Protection 

To reduce the possibility of screen burn, this unit is equipped with screen burn prevention technology. This technology enables you to set picture movement up/down (Vertical) and side to side (Horizontal). The Time setting allows you to program the time between movement of the picture in minutes.

Pixel Shift • : Using this function, you can minutely move pixels on the PDP in horizontal or vertical direction to minimize after

image on the screen.

Optimum condition for pixel shift

Item TV/Ext./AV/Component/HDMI/PC

Horizontal 0~2 2

Vertical 0~4 4

Time (minute) 1~4 min 2 min

The Pixel Shift value may differ depending on the monitor size (inches) and mode.

This function is not available in the NScreen Fit mode.

Scrolling • : This function helps remove after images on the screen by moving all the pixels on the PDP according to a pattern. Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image

on the screen for a long time. Side Grey • : When you watch TV with the screen ratio of 4:3, the screen is prevented from any damage by adjusting the white

balance on both extreme left and right sides.

- Light: When you set the screen ratio to 4:3, it brightens the left and right sides.

- Dark: When you set the screen ratio to 4:3, it darkens the left and right sides.

Picture Reset → ❑Reset Picture Mode / Cancel

Resets all picture settings to the default values.

Select a picture mode to be reset. The reset is performed for each picture mode.

Advanced Settings

Picture

Picture Options

Picture

Picture Reset ►

English - 18

English - 19

Setting up the TV with your PC

Preset: Press the N SOURCE button to select PC mode.

Auto Adjustment

❑

Auto Adjustment allows the PC screen of set to self-adjust to the incoming PC video

signal. The values of ne, coarse and position are adjusted automatically.

This function does not work in DVI-HDMI mode.

Press the TTOOLS button to display Tools menu. You can also set the auto adjustment by selecting Tools → Auto Adjustment.

Screen

❑

The purpose of picture quality adjustment is to remove or reduce picture noise. If the noise is not removed by Fine-tuning alone, then adjust the frequency as best as possible (Coarse) and Fine-tune again. After the noise has been reduced, readjust the picture so that it is aligned on the center of screen.

Coarse 

Adjusts the frequency when vertical noise appears on the screen.

Fine 

Adjusts the screen to be clearer.

PC Position 

Adjust the PC’s screen positioning if it does not t the TV screen. Press the ▲ or ▼ button to adjusting the Vertical-Position. Press the ◄ or ► button to adjust the Horizontal-Position.

Image Reset 

You can replace all image settings with the factory default values.

Brightness : 45

Sharpness : 50

Picture

Auto Adjustment ►

Screen Advanced Settings

Picture Options

Picture Reset

PC Display

Setting Up Your PC Software (Based on Windows XP)

❑

The Windows display-settings for a typical computer are shown below. The actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card. However, even if your actual screens look different, the same basic set-up information will apply in almost all cases. (If not,

contact your computer manufacturer or Samsung Dealer.)

1. First, click on ‘Control Panel’ on the Windows start menu.

2. When the control panel window appears, click on ‘Appearance and Themes’ and a

display dialog-box will appear.

3. When the control panel window appears, click on ‘Display’ and a display dialog-box

will appear.

4. Navigate to the ‘Settings’ tab on the display dialog-box.

The correct size setting (resolution) Optimum: 1920 X 1080 pixels

If a vertical-frequency option exists on your display settings dialog box, the correct value is ‘60’ or ‘60 Hz’. Otherwise, just click ‘OK’ and exit the dialog box.

Display Modes

❑

Both screen position and size will vary depending on the type of PC monitor and its resolution. The resolutions in the table are recommended.

When using an HDMI/DVI cable connection, you must use the HDMI IN 1(DVI) jack.

The interlace mode is not supported.

The set might operate abnormally if a non-standard video format is selected.

Separate and Composite modes are supported. SOG is not supported.

Too long or low quality VGA cable can cause picture noise at high resolution modes (1920x1080).

D-Sub and HDMI/DVI Input 

Mode Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock Frequency (MHz) Sync Polarity (H/V)

IBM

MAC

VESA CVT

VESA DMT

VESA DMT /

DTV CEA

VESA GTF

640 x 350 31.469 70.086 25.175 + / -

720 x 400 31.469 70.087 28.322 - / +

640 x 480 35.000 66.667 30.240 - / -

832 x 624 49.726 74.551 57.284 - / -

1152 x 870 68.681 75.062 100.000 - / +

720 x 576 35.910 59.950 32.750 - / +

1152 x 864 53.783 59.959 81.750 - / +

1280 x 720

1280 x 960 75.231 74.857 130.000 - / +

640 x 480

800 x 600 37.879 60.317 40.000 + / +

800 x 600 48.077 72.188 50.000 + / +

800 x 600 46.875 75.000 49.500 + / +

1024 x 768

1152 x 864 67.500 75.000 108.000

1280 x 800

1280 x 960 60.000 60.000 108.000

1280 x 1024

1360 x 768 47.712 60.015 85.500

1440 x 900

1680 x 1050 65.290 59.954 146.250

1920 x 1080p 67.500 60.000 148.500

1280 x 720 52.500 70.000 89.040

1280 x 1024 74.620

44.772 59.855 74.500 - / +

56.456 74.777 95.750 - / +

31.469 59.940 25.175 - / -

37.861 72.809 31.500 - / -

37.500 75.000 31.500 - / -

48.363 60.004 65.000 - / -

56.476 70.069 75.000 - / -

60.023 75.029 78.750 + / +

49.702 59.810 83.500

62.795 74.934 106.500

63.981 60.020 108.000

79.976 75.025 135.000

55.935 59.887 106.500

70.635 74.984 136.750

70.000

128.943

+ / +

- / +

+ / +

- / +

+ / +

- / +

- / -

English - 20

English - 21

Sound Control

Changing the Sound Setting

Mode

❑

You can select the type of special sound effect to be used when watching a given broadcast.



Standard / Music / Movie / Clear Voice / Custom

Press the T TOOLS button to display Tools menu.

You can also congure the sound mode by selecting Tools → Sound Mode.

Equalizer

❑

The sound settings can be adjusted to suit your personal preferences.

Mode • : You can select a sound mode to suit your personal preferences. Balance • : Controls the balance between the right and left speakers. 100Hz / 300Hz / 1KHz / 3KHz / 10KHz • (Bandwidth Adjustment): Adjusts the level of different bandwidth frequencies Reset • : Resets the equalizer settings to the default values.

SRS TruSurround HD → Off / On

❑

SRS TruSurround HD is the combined technology of TruSurround and FOCUS, TruBass. SRS TruSurround HD enables you to enjoy a virtual 5.1 Surround Sound effect over the TV's two speakers.

This function provides not only rich deep bass also improves high frequency resolution.

Press the TTOOLS button to display Tools menu. You can also set the SRS TruSurround HD by selecting Tools → SRS TS HD.

Sound

Mode : Custom

Equalizer

SRS TruSurround HD : Off

Audio Language : ----

Audio Format : ----

Audio Description

Auto Volume : Off

Speaker Select : TV Speaker

►

TruSurround HD, SRS and the symbol are trademarks of SRS Labs, Inc. TruSurround HD technology is incorporated under license from SRS Labs, Inc.

N SRS TruSurround HD (Off/On).

If the sound is abnormal while TV is playing music, please adjust the equalizer and

Audio Language ❑ (Digital channel only)

You can change the default value for audio languages. Displays the language information for the incoming stream.

You can only select the language among the actual languages being broadcast.

Audio Format → MPEG / Dolby Digital ❑ (Digital channel only)

When sound is emitted from both the main speaker and the audio receiver, a sound echo may occur due to the decoding speed

difference between the main speaker and the audio receiver. In this case, use the TV Speaker function.

You can only select the language among the actual languages being broadcast.

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

Audio Description ❑ (Digital channel only)

This is an auxiliary audio function that provides an additional audio track for visually challenged persons. This function handles the

Audio Stream for the AD (Audio Description), when it is sent along with the Main audio from the broadcaster. Users can turn the

Audio Description On or Off and control the volume.

You can select these options simply by pressing the

O AD button on the remote

control.

Audio Description →  Off / On

Turn the audio description function on or off.

Volume 

Adjusts the audio description volume.

Volume

N is active when Audio Description is set to On.

Continued...

Auto Volume → Off / On

❑

Each broadcasting station has its own signal conditions, and so it is not easy to adjust the volume every time the channel is changed. This feature lets you automatically adjust the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low.

Speaker Select → External Speaker / TV Speaker

❑

If you want to hear the sound through separate speakers, cancel the internal amplier.

The

N – +, MMUTE buttons do not operate when the Speaker Select is set to External Speaker.

If you select

N External Speaker in the Speaker Select menu, the sound settings will be limited.

TV's Internal Speakers

TV / Ext. / AV / Component / PC / HDMI

Audio Out (Optical, L / R Out) to Sound System

TV / Ext. / AV / Component / PC / HDMI

TV Speaker Speaker Output Sound Output

External Speaker Mute Sound Output

Video No Signal Mute Mute

Sound Select

❑

When the PIP feature is activated, you can listen to the sound of the sub (PIP) picture.

Main • : Listen to the sound of the main picture. Sub • : Listen to the sound of the sub picture.

Press the TTOOLS button to to display Tools menu. You can also set the sound of the sub picture by selecting Tools → PIP → Sound Select.

You can select this option when

N PIP is set to On.

Sound Reset

❑

Reset All / Reset Sound Mode / Cancel  :

factory defaults.

You can restore the Sound settings to the

Speaker Select : TV Speaker

Sound Select : Main

Sound

Sound Reset ►

Selecting the Sound Mode

When you set to Dual l ll, the current sound mode is displayed on the screen.

Type of broadcast

Regular broadcast

(Standard audio)

NICAM

Stereo

Regular + NICAM Mono

NICAM-Stereo

NICAM Dual-I/II

Regular broadcast

(Standard audio)

Bilingual or DUAL-I/II

Stereo Stereo

If the stereo signal is weak and an automatic switching occurs, then switch to the mono. N This function is only activated in stereo sound signal. It is deactivated in mono sound signal. N This function is only available in N TV mode.

Press the TTOOLS button to to display Tools menu. You can also select the sound mode by selecting Tools → Dual l ll.

English - 22

NICAM

Stereo

NICAM

Dual-1

Dual I Dual II

On-screen indication

Mono (Normal use)

NICAM

Dual-2

Mono (Normal use)

Mono

(Normal)

Mono

(Normal)

Mono

(Normal)

Mono

(Forced mono)

English - 23

Function Description

Setting the Time

Clock

❑

Setting the clock is necessary in order to use the various timer features of the TV.

The current time will appear every time you press the

N INFO button.

If you disconnect the power cord, you have to set the clock again.

Clock Mode 

You can set up the current time manually or automatically.

Plug & Play

Menu Language : English

Setup

Time ►

Broadcast

Security Network

General

Auto • : Set the current time automatically using the time from the digital broadcast. Manual • : Set the current time to a manually specied time.

Clock Set 

You can set the current time manually.

Set up this item when you have set

N Clock Mode to Manual.

You can set the

N Day, Month, Year, Hour, Minute directly by pressing the number

buttons on the remote control.

Sleep Timer → Off / 30 min / 60 min / 90 min / 120 min / 150 min

❑

/ 180 min

Clock : -- : -- ► Sleep Timer : Off

Timer 1 : Inactivated

Timer 2 : Inactivated

Timer 3 : Inactivated

Time

Move E Enter R Return

The sleep timer automatically shuts off the TV after a preset time. (30, 60, 90, 120, 150 and 180 minutes).

The TV automatically switches to standby mode when the timer reaches 0.

To cancel the N Sleep Timer function, select Off.

Press the TTOOLS button to display Tools menu. You can also set the sleep timer by selecting Tools → Sleep Timer.

Timer 1 / Timer 2 / Timer 3

❑

You can set the TV to turn on or off at a desired time.

On Time • : Sets the time for the TV to turn on. Off Time • : Sets the time for the TV to turn off. Volume • : Set the required volume level. Source • : Selects TV, USB device.

When you select the

N TV, you can set the Antenna and Channel.

Antenna - : Selects Air or Cable. Channel - : Select the desired channel.

When you select the

N USB, you can set the Contents.

Contents - : Selects the desired contents on the USB.

Repeat • : Select Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual.

When

N Manual is selected, press the ► button to select the desired day of the week. Press the ENTER

button over the

desired day and the c mark will appear.

The whole folder on the USB are supports English 64 character.

You must set the clock rst. N

You can set the hour, minute and programme by pressing the number buttons on the remote control. N

Auto Power Off N

When you set the timer On, the television will eventually turn off, if no controls are operated for 3 hours after the TV was turned on by the timer. This function is only available in timer On mode and prevents overheating, which may occur if a TV is on for too long time.

Configuring the Setup Menu

Menu Language

❑

You can set the menu language.

Broadcast

❑

Subtitle 

You can activate and deactivate the subtitles. Use this menu to set the Subtitle Mode.

Normal under the menu is the basic subtitle and Hard of hearing is the subtitle for a hearing-impaired person.

Subtitle → • Off / On: Switches subtitles off or on. Mode → • Normal / Hard of hearing: Sets the subtitle mode.

Subtitle Language • : Set the subtitle language.

If the programme you are watching does not support the

N Hard of hearing function,

Normal automatically activates even though Hard of hearing mode is selected. English is the default in cases where the selected language is unavailable in the

broadcast. You can select these options simply by pressing the

O SUBT. button on the remote

control.

Digital Text → Disable / Enable 

If the programme is broadcast with digital text, this feature is enabled.

MHEG (Multimedia and Hypermedia Information Coding Experts Group)

An International standard for data encoding systems used in multimedia and hypermedia. This is at a higher level than the MPEG system which includes

data-linking hypermedia such as still images, character service, animation, graphic and video les as well as multimedia data. MHEG is user runtime interaction technology and is being applied to various elds including VOD (Video-On-Demand), ITV

(Interactive TV), EC (Electronic Commerce), tele-education, tele-conferencing, digital libraries and network games.

Plug & Play

Setup

Menu Language : English ►

Time

Broadcast

Security Network

General

Teletext Language 

You can set the Teletext language by selecting the language type.

English is the default in cases where the selected language is unavailable in the broadcast.

Preference 

Primary • Audio Language / Secondary Audio Language / Primary Subtitle Language / Secondary Subtitle Language / Primary Teletext Language / Secondary Teletext Language

Using this feature, users can select one of the languages. The language selected here is the default when the user selects a

channel.

If you change the language setting, the Subtitle Language, Audio Language, and the Teletext Language of the Language menu

are automatically changed to the selected language.

The Subtitle Language, Audio Language, and the Teletext Language of the Language menu show a list of languages supported

by the current channel and the selection is highlighted. If you change this language setting, the new selection is only valid for the

current channel. The changed setting does not change the setting of the Primary Subtitle Language, Primary Audio Language, or the Primary Teletext Language of the Preference menu.

Common Interface 

Installing the CI(CI+) Card •

1. Purchase the CI(CI+) CAM module by visiting your nearest dealer or by phone.

2. Insert the CI(CI+) CARD into the CAM in the direction of the arrow until it ts.

3. Insert the CAM with the CI(CI+) CARD installed into the common interface slot.

Insert the CAM in the direction of the arrow, right up to the end so that it is

parallel with the slot.

4. Check if you can see a picture on a scrambled signal channel. CI(CI+) • Menu

This enables the user to select from the CAM-provided menu.

Select the CI(CI+) Menu based on the menu PC Card.

Application Info. • This contains information on CAM inserted in the CI(CI+) slot and displays it. The Application Info inserting is about the CI(CI+) CARD. You can install the CAM

anytime whether the TV is ON or OFF.

CAM is not supported in some countries and regions, check with your authorized dealer.

English - 24

Continued...

English - 25

Security

❑

Child Lock → Off / On 

This feature allows you to prevent unauthorized users, such as children, from watching unsuitable programmes by muting out video and audio.

Before the setup screen appears, the PIN number input screen appears. Enter your 4 digit PIN number.

The default PIN number of a new TV set is N ‘0-0-0-0’. You can change the PIN by selecting Change PIN from the menu. You can lock some channels in Channel List.

N (refer to page 14)

Child Lock

N is available only in TV mode.

Parental Lock 

This feature allows you to prevent unauthorized users, such as children, from watching unsuitable programmes by a 4-digit PIN (Personal Identication Number) code that is dened by the user.

The Parental Rating item differs depending on the country.

Before the setup screen appears, the PIN number input screen appears. Enter your 4 digit PIN number. N The default PIN number of a new TV set is N ‘0-0-0-0’. You can change the PIN by selecting Change PIN from the menu.

When the parental ratings are set, the “

Allow All / Block All

N : Press to unlock or lock all TV ratings.

Change PIN 

You can change your personal ID number that is required to set up the TV.

Before the setup screen appears, the PIN number input screen appears. Enter your 4 digit PIN number

(The default PIN number : ‘0-0-0-0’). If you forget the PIN code, press the remote control buttons in the following sequence, which resets the PIN to ‘0-0-0-0’:

POWER (Off), MMUTE, 8, 2, 4, POWER (On).

General

❑

Game Mode → Off / On 

When connecting to a game console such as PlayStationTM or XboxTM, you can enjoy a more realistic gaming experience by

selecting the game menu.

When the Game Mode is On •

Picture Mode - is automatically changed to Standard and users cannot change the mode.

Sound Mode - is automatically changed to Custom and users cannot change the mode. Adjust the sound using the equalizer.

The - Reset in the Sound menu is activated. Reset function initializes the Equalizer settings to the factory default setting.

Game Mode

If the picture is poor when external device is connected to TV, check if

If you display the TV menu in

The mark

This function supports only game function.

Game mode N is not available in PC mode.

is not available in regular TV mode or Game Mode set to Off.

appears on the screen which means that Game Mode is on with the selected source.

” symbol is displayed.

Game mode, the screen shakes slightly.

Game Mode is On.

BD Wise → Off / On 

Wise is a function that enables you automatically to set the optimum condition all connected Samsung devices that support BD

Wise.

This function is active only when an external device is connected to the TV via HDMI.

When the N BD Wise set to On, picture mode is automatically changed under the conditions

Continued...

Energy Saving → Off / Low / Medium / High / Picture Off 

This feature adjusts the brightness of the TV in order to reduce power consumption. When watching TV at night, set the Energy Saving mode option to High to reduce eye fatigue as well as power consumption.

If you select Picture Off, the screen is turned off and you can only hear the sound. Press any button to get out of Picture Off.

In the Tools menu,

N Picture Off function is not supported.

Press the TTOOLS button to display Tools menu. You can also set the Energy Saving option by selecting Tools → Energy Saving.

Menu Transparency 

You can set the transparency of the on-screen menu.

Bright • : Sets the on-screen menu to normal. Dark • : changes the on-screen menu to opaque.

Melody → Off / Low / Medium / High 

The TV power on / off melody sound can be adjusted.

The Melody does not play

- When no sound is output from the TV because the M MUTE button has been pressed.

- When no sound is output from the TV because the –

(Volume) button has been pressed.

- When the TV is turned off by Sleep Timer function.

Viewing the Picture in Picture (PIP)

You can display a sub picture within the main picture of set programme me or video input. In this way, you can watch the picture of set programme me or video input from any connected equipment while watching the main picture.

You may notice that the picture in the PIP window becomes slightly unnatural when you use the main screen to view a game or karaoke.

Press the TTOOLS button to display Tools menu. You can also congure PIP related settings by selecting Tools → PIP.

PIP → Off / On

❑

Game Mode : Off

BD Wise : Off

Energy Saving : Off

Menu Transparency : Bright

Melody : Medium PIP ►

You can activate or deactivate the PIP function.

Main picture Sub picture

Component

HDMI1/DVI, HDMI 2, HDMI 3, HDMI 4

PIP : Off ►

Size :

Position :

Channel : ATV 1

Size →  / / /

You can select a size of the sub-picture.

If main picture is in

N HDMI mode, Size is not available.

Position →  / / /

You can select a position of the sub-picture.

In Double (

N , ) mode, Position cannot be selected.

Channel 

You can select a channel of the sub-picture.

General

Move E Enter R Return

PIP

E Enter R Return

English - 26

English - 27

Support / Input

Supported Program

Product Guide

❑

The Product Guide gives you information on the most important features of this TV.

For more detailed information, select the desired item.

Self Diagnosis

❑

Picture Test 

If you think you have a picture problem, perform the picture test. Check the colour pattern on the screen to see if the problem still exists.

Does the problem still exist with this test photo?

N appears on the screen.

If the test pattern does not appear or there is noise in the test pattern, select Yes. If the test pattern is properly displayed, select No.

Yes • : There may be a problem with the TV. Contact Samsung’s Call Center for assistance. No • : There may be a problem with your external equipment. Please check your connections. If the problem still persists,

refer to the external device’s user manual.

Sound Test 

If you think you have a sound problem, please perform the sound test. You can check the sound by playing a built-in melody sound through the TV.

Does the problem still exist with this sound test?

N appears on the screen.

If during the sound test you can hear sound only from one speaker or not at all, select Yes.If you can hear sound from the

speakers, select No.

to the external device’s user manual.

If you hear

N no sound from the TV’s speakers, before performing the sound test, make sure Speaker Select is set to TV speaker

in the Sound menu.

The melody will be heard during the test even if

N Speaker Select is set to External Speaker or the sound is muted by pressing

the MMUTE button.

Signal Information  (Digital channels only)

You can adjust your antenna to improve the reception of available digital channels.

If the signal strength meter indicates that the signal is weak, physically adjust your antenna to increase the signal strength.

Continue to adjust the antenna until you nd the best position with the strongest signal.

Continued...

Software Upgrade

❑

To keep your product up-to-date with new Digital Television features then software upgrades are periodically broadcast as part of the normal Television signal. It will automatically detect these signals and display the software upgrade banner. You are given the option to install the upgrade.

By USB 

Insert a USB drive containing the  rmware upgrade into TV. Please be careful to not disconnect the power or remove the USB drive while upgrades are being applied. The TV will turn off and turn on automatically after completing the  rmware upgrade. Please check the  rmware version after the upgrades are complete. When software is

upgraded, video and audio settings you have made will return to their default (factory) settings.

By Channel 

Upgrades the software using the broadcasting signal.

If the function is selected during the software transmission period, this function

searches for available software and downloads the software. The time required to download the software is determined by the signal status.

Standby Mode Upgrade 

To continue software upgrade with master power on, Select On by pressing the ▲ or ▼ button. 45 minutes after entering standby mode, a manual upgrade is automatically conducted. Since the power of the unit is turned on internally, the screen may be on

slightly for the product. This phenomenon may continue for more than 1 hour until the software upgrade is completed.

Alternative Software 

Show the previous version that would be replaced.

If software was changed, existing software is displayed.

You can change current software to alternative software by Alternative Software. N

HD Connection Guide

❑

The brief instruction on how to get the best performance from your new HDTV is displayed. We offer the connection method for HD devices.

You can move the previous or next page by pressing the ◄ or ► button.

TV Rear Panel

USB Drive

Contact Samsung

❑

You can know the Samsung Call center, website and information for product.

Source List / Edit Name

Source List

❑

Use to select TV or other external input sources such as DVD players or Cable Box / Satellite receivers (Set-Top Box) connected to the TV. Use to select the input source of

your choice.

TV, Ext., AV, Component, PC, HDMI1/DVI, HDMI2, HDMI3, HDMI4, USB. 

You can choose only those external devices that are connected to the TV. In the N Source List, connected inputs will be highlighted and sorted to the top. Inputs that are not connected will be sorted to the bottom.

Using the Colour buttons on the remote with the Source list

- Red (Refresh): Refreshes the connecting external devices.

- T TOOLS (Tools): Displays the Edit Name and Information menus.

Press the

O SOURCE button on the remote control to view an external signal

source.

Edit Name

❑

You can name the device connected to the input jacks to make your input source selection easier.

VCR / DVD / Cable STB / Satellite STB / PVR STB / AV Receiver / Game / Camcorder / PC / DVI / DVI PC / TV / IPTV /  Blu-ray / HD DVD / DMA

When a PC with a resolution of 1920 x 1080@60Hz is connected to the N HDMI IN 1 (DVI) port, you should set the HDMI1/DVI mode to PC in the Edit Name of the Input mode.

Input

Source List

Edit Name

English - 28

English - 29

Network

Network Connection

Network Connection is for DLNA, Contents Library-Internet download and Home Network Centre.

Network Connection - Cable

❑

LAN Connection for a DHCP Environment 

The procedures to set up the network using Dynamic Host Conguration Protocol (DHCP) are described below. Since an IP address, subnet mask, gateway, and DNS are automatically allocated when DHCP is selected, you do not have to enter

them manually.

TV Rear Panel

The Modem Port

on the Wall

1. Connect the LAN port on the rear panel of the TV and the external modem with a LAN Cable.

2. Connect the LAN port on the wall and the external modem with a Modem Cable.

External Modem

(ADSL/VDSL/Cable TV)

Modem Cable

LAN Cable

You can connect the LAN via a Sharer (Router).

IP Sharer

The Modem Port

on the Wall

You can connect the LAN port and the TV directly depending on your network status.

The LAN Port

on the Wall

External Modem

(ADSL/VDSL/

Cable TV)

Modem Cable

TV Rear Panel

LAN Cable

TV Rear Panel

The terminals (the position of the port and the type) of the external device may differ depending on the manufacturer. N If the IP address allocation by the DHCP server has failed, turn the external modem off, turn it on again after at least 10 seconds N

and then try again.

For the connections between the external modem and the Sharer (Router), refer to the owner’s manual of the corresponding

product.

You can connect the TV to the LAN directly without connecting it through a Sharer (Router).

You cannot use a manual-connection-type ADSL modem because it does not support DHCP. You have to use an automatic- N connection-type ADSL modem.

Continued...

LAN Connection for Static IP Environment 

The procedures to set up the network using a static IP address are described below. You have to manually enter the IP address,

subnet mask, gateway, and DNS that are provided by your Internet Service Provider (ISP).

TV Rear Panel

The LAN Port

on the Wall

LAN Cable

1. Connect the LAN port on the rear panel of the TV and the LAN port on the wall using the LAN cable.

You can connect the LAN via a Sharer (Router).

The LAN Port

on the Wall

LAN Cable

IP Sharer

TV Rear Panel

LAN Cable

The terminals (the position of the port and the type) of the external device may differ depending on the manufacturer. N If you are using a static IP address, your ISP will inform you of the IP address, subnet mask, gateway, and DNS. N

You must enter these values to complete the network settings. If you do not know the values, ask your network administrator.

For the information on how to congure and connect a Sharer (Router), refer to the owner’s manual for the corresponding product.

You can connect the TV to the LAN directly without connecting it through a Sharer (Router). N If you use an IP Sharer (IP Router) that supports DHCP, you can set up the device as either DHCP or static IP. N For the procedures to use a static IP address, ask your Internet Service Provider. N

Network Connection - Wireless

❑

You can connect to the network wirelessly through a wireless IP sharer.

TV Rear Panel

Samsung Wireless LAN Adapter

Wireless IP sharer

LAN Cable

The LAN Port

on the Wall

1. Connect the ‘Samsung Wireless LAN Adapter’ into the USB 1 (HDD) or USB 2 terminal of the TV.

You must use the ‘Samsung Wireless LAN Adapter to use a wireless network.

Samsung’s Wireless LAN adapter is sold separately. The WIS09ABGN Wireless LAN adapter is offered by select retailers, N Ecommerce sites and Samsungparts.com.

To use a wireless network, your TV must be connected to a wireless IP sharer.

If the wireless IP sharer supports DHCP, your TV can use a DHCP or static IP address to connect to the wireless network. N

Samsung’s Wireless LAN adapter supports IEEE 802.11A, IEEE 802.11B, IEEE 802.11G, IEEE 802.11N. When you play DLNA N

video over IEEE 802.11B/G connection, the video may not be played smoothly. If the wireless IP sharer allows you to turn the Ping connection function on/off, turn it on.

Select a channel for the wireless IP sharer that is not currently being used. If the channel set for the wireless IP sharer is currently N

being used by another device nearby, this will result in interference and communications may fail.

English - 30

Continued...

+ 193 hidden pages