Samsung PS-37S4A User Manual

Download

Page 1

PDP-TELEVISION (PLASMA DISPLAY PANEL)

Owner’s Instructions

Before operating the unit,

please read this manual thoroughly,

and retain it for future reference.

ON-SCREEN MENUS

PICTURE IN PICTURE (PIP)

TELETEXT / TELEWEB

(OPTION)

Page 2

ENG

User Instructions

◆ Screen Image retention

Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of this screen when displaying a still image.

◆ Cell Defect

The plasma display panel consists of fine cells. Although the panels are produced with more than

99.9 percent active cells, there may be some cells that do not produce light or remain lit.

◆ Height

The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height and do not install and operate there.

◆ Heat

PDP TV displays picture by Plasma discharge. For this reason, using the PDP TV for a long period of time results in dissipation of heat by the panel. Please note that the top side of the product may be hot after use for long periods of time as the heat dissipation from the panel through the vent hole in the upper part of the product. You don't have to worry since PDP TV’s heat dissipation does not necessarily indicate any defect or operation failure of the product. Particularly when watching TV with children, adults should prevent children from touching the upper part of the product.

◆ Warranty

- Warranty does not cover any damage caused by image retention.

- Burn-in is not covered by the warranty.

Page 3

Checking Parts

ENG

Sold Separately

Owner’s Instructions

S-VIDEO Cable

Remote Control/

AAA Batteries

Component Cables

Power Cord

Antenna Cable

Scart Cable PC Audio Cable

DNIeTM(Digital Natural Image engine)

This feature bring you more detailed image with 3D noise reduction, detail enhancement, contrast enhancement and white enhancement. New image compensation Algorithm gives brighter, clearer, much detailed image to you. DNIe every signals into your eyes.

technology will fit

DVI Cable

PC Cable

(RCA)

Page 4

ENG

◆ FOREWORD

■ User Instructions............................................................................................ 2

◆ CONNECTING AND PREPARING YOUR DISPLAY

■ Your New Plasma Display Panel................................................................... 6

■ Infrared Remote Control ................................................................................ 8

■ Inserting the Batteries in the Remote Control................................................ 9

■ Assembling the Stand-Base .......................................................................... 9

■ Installing the Display on the Wall Attachment Panel ..................................... 10

■ Connecting to an Aerial or Cable Television Network ................................... 12

■ Connecting a Satellite Receiver or Decoder.................................................. 12

■ Switching On and Off..................................................................................... 13

■ Placing in Standby Mode............................................................................... 13

■ Becoming Familiar with the Remote Control ................................................. 14

■ Setting Up Your Remote Control ................................................................... 15

■ Plug & Play Feature....................................................................................... 16

■ Choosing Your Language.............................................................................. 17

◆ SETTING THE CHANNELS

■ Storing Channels Automatically..................................................................... 18

■ Storing Channels Manually............................................................................ 19

■ Skipping Unwanted Channels ....................................................................... 21

■ Sorting the Stored Channels ......................................................................... 22

■ Assigning Names to Channels ...................................................................... 23

■ Using the LNA (Low Noise Amplifier) Feature............................................... 24

■ Activating the Child Lock ............................................................................... 25

■ Displaying Information ................................................................................... 26

◆ USING YOUR DISPLAY

■ Changing the Picture Standard ..................................................................... 26

■ Adjusting the Picture Settings........................................................................ 27

■ Adjusting the Picture Settings (PC or DVI Mode) .......................................... 28

■ Setting the Picture (PC Mode)....................................................................... 29

■ Using the Fine Tune ...................................................................................... 31

■ Viewing the Channel Scan Picture ................................................................ 32

■ Freezing the Current Picture ......................................................................... 32

■ Selecting the Picture Size.............................................................................. 33

■ Selecting the Film Mode ................................................................................ 34

■ DNIe

■ Setting the Blue Screen................................................................................. 35

■ Setting the Melody Sound ............................................................................. 35

■ Viewing the Picture In Picture (PIP) .............................................................. 36

■ Using the Digital NR (Digital Noise Reduction) Feature ................................ 38

■ Changing the Sound Standard ...................................................................... 39

(Digital Natural Image engine) ............................................... 34

Page 5

Contents (continued)

◆ USING YOUR DISPLAY (continued)

■ Adjusting the Sound Settings ........................................................................ 40

■ Adjusting the Volume Automatically .............................................................. 40

■ Setting the TruSurround XT........................................................................... 41

■ Selecting the Internal mute............................................................................ 41

■ Selecting the Sound Mode (depending on the model) .................................. 42

■ Setting the Sleep Timer ................................................................................. 43

■ Setting and Displaying the Current Time....................................................... 44

■ Switching the Television On and Off Automatically ....................................... 45

■ Viewing an External Signal Source ............................................................... 46

■ Redirecting an Input to the External Output .................................................. 47

◆ USING THE TELETEXT FEATURE

■ Teletext Feature ............................................................................................ 48

■ Displaying the Teletext Information ............................................................... 49

■ Selecting Display Options.............................................................................. 50

■ Selecting a Teletext Page.............................................................................. 51

◆ USING THE TELEWEB FEATURE (OPTION)

■ TeleWeb Feature........................................................................................... 52

■ Using the TeleWeb Menu after Displaying the TeleWeb............................... 53

■ Easy Accessing the TeleWeb Service via the Remote Control ..................... 54

ENG

◆ ADDITIONAL INFORMATION AND CONNECTIONS

■ Connecting to the External Devices .............................................................. 55

■ Connecting to the S-Video Input.................................................................... 56

■ Connecting to the DVI Input .......................................................................... 57

■ Connecting to the PC Input ........................................................................... 57

■ Connecting to the Component Input.............................................................. 58

■ Connecting and Using the Home Theater System ........................................ 59

■ Setting up Your PC Software (Windows only) ............................................... 60

■ Input Mode (PC/DVI) ..................................................................................... 61

■ Pin Configurations ......................................................................................... 62

◆ RECOMMENDATIONS FOR USE

■ Troubleshooting: Before Contacting Service Personnel................................ 63

■ Programming the Remote Control for Other Components ............................ 64

Symbols

Press Important Note

☛

➢

Page 6

ENG

Your New Plasma Display Panel

The actual configuration on your PDP may be different,

➢

depending on your model.

Front Panel

Speaker

SOURCE

External input selection.

Menu display.

Volume adjustment. Also used to select or adjust items on the on-screen menu.

C/P.

Channel selection. Auto power On. Also used to move up or down in the on-screen menu.

Confirm your choice (Store or Enter).

a c

Touch button

Touch the printed names

of each button using your

finger to operate it.

I /

Press to turn the PDP on and off.

Power Indicator

-Power Off: Blue

- Power On: Off

Remote Control Signal Receiver

Aim the remote control towards this spot on the PDP.

Page 7

Your New Plasma Display Panel (continued)

The actual configuration on your PDP may be different,

➢

depending on your model.

Rear Panel

For further details about connection, refer to pages 55~59.

➢

ENG

a) DVI INPUT (DVI-D / L-AUDIO-R)

Connect to the digital video and audio output jack for device with DVI output.

b) MONITOR OUT (VIDEO / L-AUDIO-R)

Outputs for external devices.

c) EXT.1, EXT.2, EXT.3

Inputs or outputs for external devices, such as VCR, DVD, video game device or video disc players.

d) PC INPUT (RGB IN / AUDIO)

Connect to the video and audio output jack on your PC.

e) ONLY FOR SERVICE

Connector for service only.

f) AV2 (S-VIDEO / L-AUDIO-R)

Video and audio inputs for external devices with an S-Video output, such as a camcorder or VCR.

g) AV1, AV2

(VIDEO / L-AUDIO-R)

Video and audio inputs for external devices, such as a camcorder or VCR.

h) COMPONENT1, COMPONENT2

Video (Y/Pb/Pr) and audio (L-AUDIO-R) inputs for Component.

i) ANT IN VHF/UHF (75Ω)

75Ω Coaxial connector for Aerial/Cable Network.

j) POWER IN

Connect the supplied power cord.

Page 8

ENG

Infrared Remote Control

TURNS THE PDP ON AND OFF

PICTURE EFFECT SELECTION

WHEN YOU PRESS A BUTTON , ‘ APPEARS ALONG WITH SELECTED MODE

(TV, VCR, CATV, DVD OR STB) AND REMAINING BATTERIES ON LCD

’

SOUND EFFECT SELECTION

TELETEXT CANCEL

DIRECT CHANNEL SELECTION

TELETEXT SIZE SELECTION

TEMPORARY SOUND SWITCH-OFF

MIX BOTH TELETEXT INFORMATION

AND THE NORMAL BROADCAST

MOVE TO THE REQUIRED

ADJUST AN OPTION VALUE

(DEPENDING ON THE MODEL)

FASTEXT TOPIC SELECTION

PICTURE SIZE/

VOLUME INCREASE

VOLUME DECREASE

TELETEXT DISPLAY/

MENU DISPLAY/

TELETEXT INDEX

MENU OPTION/

RESPECTIVELY

PICTURE STILL

TELEWEB DISPLAY

MAKE THE REMOTE CONTROL WORKS FOR TV, VCR, CATV, DVD PLAYER, STB

AUTOMATIC SWITCH-OFF/ TELETEXT SUB-PAGE

NEXT CHANNEL/ TELETEXT NEXT PAGE/ TELEWEB FORWARD

EXTERNAL INPUT SELECTION/ TELETEXT PAGE HOLD

PREVIOUS CHANNEL/ TELETEXT PREVIOUS PAGE/ TELEWEB BACKWARD

INFORMATION DISPLAY/ TELETEXT REVEAL

TV MODE SELECTION EXIT TELETEXT EXIT TELEWEB (DEPENDING ON THE MODEL)

CONFIRM YOUR CHOICE (STORE OR ENTER)

SOUND MODE SELECTION

TruSurround XT MODE SELECTION

REMOTE CONTROL SETUP

IF YOUR REMOTE CONTROL IS NOT

FUNCTIONING PROPERLY, TAKE

OUT THE BATTERIES AND PRESS

THE RESET BUTTON FOR ABOUT

2~3 SECONDS. RE-INSERT THE

BATTERIES AND TRY USING THE

REMOTE CONTROL AGAIN.

The performance of the remote control may be affected by bright light.

➢

PIP FUNCTIONS;

- PIP ACTIVATING OR DEACTIVATING (PIP ON)

- SWAPPING THE MAIN AND THE SUB PICTURE (SWAP)

- LOCATION SELECTION (POSITION)

- SOURCE SELECTION (SOURCE)

- SIZE SELECTION (SIZE)

- SCAN

- SELECTING THE CHANNEL OF SUB PICTURE (P )

VCR/DVD FUNCTIONS;

- REWIND (REW)

- STOP

- PLAY/PAUSE

- FAST FORWARD (FF)

Page 9

Inserting the Batteries in the Remote Control

You must insert or replace the batteries in the remote control when you:

◆ Purchase the PDP

◆ Find that the remote control is no longer operating

correctly

1 Remove the cover on the rear of the remote control by pressing

the symbol ( ) downwards and then pulling firmly to remove it.

2 Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking

care to respect the polarities:

◆-on the battery against -on the remote control

◆+on the battery against +on the remote control

3 Replace the cover by aligning it with the base of the remote

control and pressing it back into place.

ENG

Assembling the Stand-Base

1 Assemble the PDP with the stand and firmly secure the PDP using

4 screws provided.

◆

➢

Two or more people should carry the PDP. Never lay the PDP on the floor because of possible damage to the screen. Always store the PDP upright.

Page 10

ENG

Installing the Display on the Wall Attachment Panel

Installation Notes

◆

Do not install the PDP on any place other than vertical walls.

◆

To protect the performance of the PDP and prevent troubles, avoid the followings:

Do not install next to smoke and fire detectors.

Do not install in an area subjected to vibration or high voltage.

Do not install near or around any heating apparatus.

◆

Use only recommended parts and components.

Mounting Kits (Sold Separately)

Wall Mount Bracket

Plastic Hanger Screws

4 EA 4 EA

Page 11

Installing the Display on the Wall Attachment Panel (continued)

The exterior of the PDP may be different than the picture.

➢

(Assembly and installation of the plastic hanger is the same.)

1 Remove the screws from the back of the PDP.

2 Use the screws and assemble the plastic hanger.

◆ Please ask the installers to install the wall mount bracket.

☛

◆ Please be sure to check if the plastic hanger is

completely secured on both the left and right side after hanging the PDP on the wall mount bracket.

◆ Please avoid catching your fingers while installing and adjusting the angle.

◆ Please tightly secure the wall mount bracket to the wall to avoid injury from a falling PDP.

ENG

3 Tighten the screws of the plastic hanger to the back side of the PDP.

4 Put the 4 pegs on the PDP in the grooves of the wall mount bracket and pull down on the PDP (!) to

secure it to the wall mount bracket ( separated from wall mount bracket.

PDP panel

Wall attachment panel bracket Wall

@). Tighten the screws as shown (#) so that the PDP cannot be

Page 12

ENG

Connecting to an Aerial or Cable Television Network

To view television channels correctly, a signal must be received by the set from one of the following sources:

◆ An outdoor aerial

◆ A cable television network

◆ A satellite network

Rear of the PDP

1 In the first three cases, connect the aerial or network input cable to

the 75Ω coaxial socket on the rear of the PDP.

2 If you are using an indoor aerial, you may need to turn it when

tuning your PDP until you obtain a picture that is both sharp and

Cable Television

Network

clear. For further details, refer to:

◆ “Storing Channels Automatically” on page 18

◆ “Storing Channels Manually” on page 19

When installing or re-installing your PDP, be sure to use the

➢

supplied coaxial antenna cable. If you connect using a different coaxial cable, there is risk of noise or interference to the screen image. (You must not use another general purpose cable. Use the 3M/5M/7M cable supplied by Samsung.)

Connecting a Satellite Receiver or Decoder

In order to watch television programmes broadcast via a satellite network, you must connect a satellite receiver to the rear of the PDP. Also, in order to descramble a coded transmission signal, you must connect a decoder to the rear of the PDP.

Satellite receiver/

Decoder

Using a Coaxial cable

Connect a coaxial cable to the:

◆ Receiver (or Decoder) output socket.

◆ Television aerial input socket.

If you wish to connect both a satellite receiver (or decoder)

➢

and a VCR, you should connect the:

◆ Receiver (or Decoder) to the VCR

◆ VCR to the PDP

Otherwise, connect the receiver (or decoder) directly to the PDP.

Page 13

Switching On and Off

The mains lead is attached to the rear of your PDP.

ENG

1 Plug the mains lead into an appropriate socket.

Result

: The Standby indicator on the front of the PDP lights up.

The main voltage is indicated on the rear of the PDP and

➢

the frequency is 50 or 60Hz.

2 Press the “ I / ” button on the front of the PDP (or POWER ()

button on the remote control) to switch the PDP on.

Result

: The programme that you were watching last is re-

selected automatically.

If you have not yet stored any channels, No clear picture

➢

appears. Refer to “Storing Channels Automatically” on page 18 or “Storing Channels Manually” on page 19.

3 To switch your PDP off, press the “ I / ” button again.

Placing in Standby Mode

Front of the PDP

Your PDP can be placed in Standby mode, in order to reduce the Power consumption.

The Standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).

1 Press the POWER () button on the remote control.

Result

: The screen is turned off and the Standby indicator on

the front of the PDP lights.

2 To switch the PDP back on, simply press the POWER () button

again or a numeric button.

You can also switch on by pressing the P or button.

➢

Page 14

ENG

Becoming Familiar with the Remote Control

The remote control is used mainly to:

◆ Change channels and adjust the volume

◆ Display the on-screen menu system

The following table presents the most frequently used buttons and their functions.

Button Viewing Function Menu Function

Used to display the next stored channel.

Used to display the previous stored channel.

to Used to display the corresponding channels.

For double digit channels, the second digit must be

➢

pushed immediately after the first. Failure to do this will result in a single digit channel being displayed.

SLEEP Used to select a preset time interval (off - 30 - 60 - 90 - 120 -

MUTE Used to switch the sound off temporarily.

MENU Used to display the Used to return to the previous

150 - 180).

Used to increase the volume.

Used to decrease the volume.

To turn the sound back on, press this button again, or

➢

press the or button.

on-screen menu system. menu or normal viewing.

Used to:

◆ Display a submenu containing selections for the current menu option

◆ Increase/decrease a menu option value

EXIT/TV

Used to confirm your choice.

Used to exit from the menu system and return to normal viewing directly.

Page 15

Setting Up Your Remote Control

This PDP’s remote control can operate VCR, CATV , DVD, or Settop box (STB), in addition to controlling the PDP.

The remote control is not compatible with the TV

➢

manufactured by another company.

1 Turn off your VCR, Cable box, DVD or STB.

2 Press the SELECT button. Mode is changed whenever SELECT

button is pressed.

3 Press the POWER () button on the remote control. The

component you select should turn on. If it turns on, your remote control is now set correctly.

4 Once your remote control is set up, press the SELECT button any

time you want to use the remote control to operate your VCR, Cable box, DVD or STB.

When your remote control is in the VCR, CATV, DVD or

➢

STB mode, the volume buttons still control your television’s volume.

ENG

VCR

To program the cable receiver controls:

➢

◆ Press the SELECT button to select CATV.

◆ Point the remote control at the cable receiver and press

the

SET button. Then press the company code number(s) for the component in page 64. Ex) If the component is manufactured by Oak, press 026.

To program the VCR controls:

➢

◆ Press the SELECT button to select VCR

◆ Point the remote control at the VCR and press the SET

button. Then press the company code number(s) for the component in page 65.

To program the DVD controls:

➢

◆ Press the SELECT button to select DVD

◆ Point the remote control at the DVD and press the SET

button. Then press the company code number(s) for the component in page 64.

Page 16

ENG

Plug & Play Feature

Plug & Play

Press ENTER to start Plug & Play

Start

Enter Exit

Language

Move Enter

When the television is initially powered ON, several basic customer settings proceed automatically and subsequently. The following settings are available.

1 If the television is in Standby mode, press the POWER () button

on the remote control.

Result

: The message Plug & Play is displayed, and then the

Language menu is automatically displayed a few seconds later.

2 Select the appropriate language by pressing the † or … button.

3 Press the ENTER () button to confirm your choice.

Result

: The message Antenna Input Check is displayed.

Plug & Play

Antenna Input Check

Country

Austria

Belgium

Croatia

Denmark

Finland France

Germany

▼ More

Move Enter

Press ENTER to start channel memory

Channel store in process. Storing.

Auto Store

40 MHz

Start

Enter Stop

Auto Store

57 MHz

Stop

Enter Stop

4 Make sure that the antenna is connected to the TV, and then

press the

Result

ENTER () button.

: The Country menu is displayed.

5 Select your country by pressing the † or … button.

6 Press the ENTER () button to confirm your choice.

Result

: The Auto Store menu is displayed.

7 To start the search, press the ENTER () button.

Result

: The search will end automatically. Channels are sorted

and stored in an order which reflects their position in the frequency range (with lowest first and highest last). When it has finished, the Clock Set menu is displayed.

➢ To stop the search before it has finished or return to normal

viewing, press the

MENU () button.

➢ Press the ENTER () button to set the clock.

8 Press the œ or √ button to move to the hour or minute.

Set the hour or minute by pressing the

9 When it has finished, the message Enjoy Your Watching is

displayed, and then the channel which has been stored will be activated.

† or … button.

Clock

Hour Min

01 00

Adjust Move Stop

Enjoy Your Watching

Page 17

Plug & Play Feature (continued)

If you want to reset this feature...

1 Press the MENU button.

: The main menu is displayed.

Result

2 Press the † or … button to select Setup.

: The options available in the Setup group are displayed.

Result

3 Press the ENTER () button.

4 Press the † or … button to select Miscellaneous.

Press the Result

5 Press the † or … button to select Plug & Play.

Press the

Result

6 For further details on how to set, refer to the opposite page.

ENTER () button.

: The options available in the Miscellaneous group are

displayed.

ENTER () button.

: The message Plug & Play is displayed.

Time

Language : English

AV Setup

Digital NR : On

Miscellaneous

PC Setup

Move Enter Return

Melody : Off

Plug & Play

Blue Screen : Off

Move Enter Return

ENG

Setup

√√ √√ √√ √√ √√

√√

Miscellaneous

√√ √√ √√

Choosing Your Language

When you start using your television for the first time, you must select the language which will be used for displaying menus and indications.

1 Press the MENU button.

: The main menu is displayed.

Result

2 Press the † or … button to select Setup.

: The options available in the Setup group are displayed.

Result

3 Press the ENTER () button

4 Press the † or … button to select Language.

Press the Result

5 Select the appropriate language by pressing the † or … button.

6 Press the ENTER () button to confirm your choice.

7 When you are satisfied with your choice, press the EXIT/TV ()

button to return to normal viewing.

ENTER () button.

: The available languages are listed.

Time

Language : English

AV Setup

Digital NR : On

Miscellaneous

PC Setup

Move Enter Return

Time

Language : English

AV Setup

Digital NR : On

Miscellaneous

PC Setup

Move Enter Return

Setup

√√ √√ √√ √√ √√

√√

Setup

√√ √√

√√

Page 18

ENG

Country : Austria

Auto Store

Manual Store

Edit

Fine Tune

Ch. Scan

Move Enter Return

Country : Austria

Auto Store

Manual Store

Edit

Fine Tune

Ch. Scan

Move Enter Return

Country : Austria

Auto Store

Manual Store

Edit

Fine Tune

Ch. Scan

Move Enter Return

Channel store in process. Storing.

Auto Store

Stop

Enter Return

Storing Channels Automatically

You can scan for the frequency ranges available to you, (availability

Channel

57 MHz

√√ √√ √√ √√ √√ √√

Austria

Belgium

Croatia

Denmark

Finland

France

†

√√ √√ √√ √√ √√ √√

depends on your country). Automatically allocated programme numbers may not correspond to actual or desired programme numbers. However you can sort numbers manually and clear any channels you do not wish to watch.

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button to select Channel.

Result

The options available in the displayed

3 Press the ENTER () button.

4 Press the † or … button to select Country.

Press the

Result

ENTER () button.

: The countries available are listed.

5 Select your country (or area) by pressing the † or … button.

➢ If you have selected the Others option but do not wish to

scan the PAL frequency range, store the channels manually (see page 19).

6 Press the ENTER () button to confirm your choice

7 Press the † or … button to select Auto Store.

Press the

Result

ENTER () button.

: The Auto Store menu is displayed.

8 Press the ENTER () button to start the search.

Result

: The search will end automatically. Channels are sorted

and stored in an order which reflects their position in the frequency range, (with lowest first and highest last). The programme originally selected is then displayed.

➢ To stop the search before it has finished, press the

MENU () button.

Channel

group are

9 When the channels have been stored, you can:

◆ Sort them in the order required (see page 22)

◆ Clear a channel (see page 21)

◆ Fine-tune channel reception if necessary (see page 31)

◆ Assign a name to the stored channels (see page 23)

◆ Activate/deactivate the Digital Noise Reduction feature

(see page 38)

Page 19

Storing Channels Manually

You can store up to 100 television channels, including those received via cable networks.

When storing channels manually, you can choose:

◆ Whether or not to store each of the channels found

◆ The programme number of each stored channel which

you wish to identify

Country : Austria

Auto Store

Manual Store

Edit

Fine Tune

Ch. Scan

ENG

Channel

√√ √√ √√ √√ √√ √√

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button to select Channel.

Result

The options available in the

Channel

group are

displayed.

3 Press the ENTER () button.

4 Press the † or … button to select Manual Store.

Press the

Result

ENTER () button.

: The option available in the Manual Store group are

displayed with

Prog. is selected.

5 To assign a programme number to a channel, find the correct

number by pressing the

† or … button.

6 If necessary, select the broadcasting standard required. Press the

œ or √ button to select Colour System and press the † or … button. The colour standards are displayed in the following order. (depending on the model).

Auto- PAL- SECAM Auto

- NT3.58 - NT4.43 - PAL60

7 Press the œ or √ button to select Sound System and press the †

or … button. The sound standards are displayed in the following order. (depending on the model).

BG- DK- I- L

Move Enter Return

Manual Store

Prog. Colour Sound

9 Auto BG

Channel Search Store

√√

Move Adjust Return

Prog. Colour Sound

9 Auto BG

Channel Search Store

œœ √√

Move Adjust Return

Prog. Colour Sound

9 Auto BG

Channel Search Store

œœ √√

Move Adjust Return

Manual Store

System System

59MHz ?

System System

59MHz ?

System System

59MHz ?

Page 20

ENG

Storing Channels Manually (continued)

Manual Store

Prog. Colour Sound

Channel Search Store

œœ √√

Move Adjust Return

Prog. Colour Sound

Channel Search Store

C 02 59MHz ?

œœ √√

Move Adjust Return

Prog. Colour Sound

Channel Search Store

C02 59MHz ?

œœ √√

Move Adjust Return

System System

9 Auto BG

59MHz ?

Manual Store

System System

9 Auto BG

Manual Store

System System

9 Auto BG

8 If you know the number of the channel to be stored, see the

following steps.

◆

Press the œ or √ button to select Channel.

◆

Press the † or … button to select C (Air channel) or S (Cable channel).

◆

Press the √ button.

◆

Press the numeric buttons (0~9), † or … button to select indicate the required number.

If no sound or abnormal sound, re-select the sound standard

➢

required.

9 If you do not know the channel numbers, select the Search by

pressing the search.

Result

œ or √ button. Press the † or … button to start the

: The tuner scans the frequency range until the first

channel or the channel that you selected is received on your screen.

10 To assign a programme number to a channel, select the Prog. by

pressing the the correct number.

œ or √ button. Press the † or … button until you find

11 To store the channel and associated programme number, select

the

Store by pressing the œ or √ button. Press the ENTER ()

button.

Manual Store

Prog. Colour Sound

Channel Search Store

C02 59MHz OK

œœ √√

Move Enter Return

System System

9 Auto BG

12 Repeat Steps 8 to 11 for each channel to be stored.

Channel mode

☛

◆ C (Real channel mode):

entering the assigned number to each air broadcasting station in this mode.

◆ S (Cable channel mode):

entering the assigned number for each cable channel in this mode.

You can select a channel by

Page 21

Skipping Unwanted Channels

◆ Skipping unwanted channels

You can exclude the channels of your choice from the channel scan operation. When you scan through the stored channels, those that you have chosen to skip are thus not displayed. All channels that you do not specifically choose to skip are displayed during scanning.

1 Press the MENU button.

Result

: The main menu is displayed.

Country : Austria

Auto Store

Manual Store

Edit

Fine Tune

Ch. Scan

Move Enter Return

ENG

Channel

√√ √√ √√ √√ √√ √√

2 Press the † or … button to select Channel.

Result

: The options available in the

displayed.

Channel group are

3 Press the ENTER () button.

4 Press the † or … button to select Edit.

Press the

Result

ENTER () button.

: The Edit menu is displayed.

5 Press the † or … button to select Add/Delete.

Press the

Result

ENTER () button.

: The Add/Delete menu is displayed with the current

channel automatically is selected.

6 Press the † or … button to select the channel to be deleted.

Press the

ENTER () button.

7 To add or delete the channel, select Added or Deleted by

pressing the confirm.

† or … button. Press the ENTER () button to

Add/Delete

Sort

Name

LNA : Off

Child Lock

Prog.

Edit

Move Enter Return

Add/Delete

----- -----

Move Enter Return

Add/Delete

----- -----

Added Deleted Deleted Deleted Deleted

Added Deleted

Deleted

Deleted Deleted

√√ √√ √√ √√ √√

Adjust Enter Return

Page 22

ENG

Country : Austria

Auto Store

Manual Store

Edit

Fine Tune

Ch. Scan

Move Enter Return

Add/Delete

Sort

Name

LNA : Off

Child Lock

Move Enter Return

Prog.

----- -----

Move Enter Return

Sorting the Stored Channels

This operation allows you to change the programme numbers of

Channel

√√ √√ √√ √√ √√ √√

Edit

√√ √√ √√ √√ √√

Sort

stored channels. This operation may be necessary after using ATM. You can delete those channels you do not want to keep.

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button to select Channel.

Result

The options available in the displayed.

3 Press the ENTER () button.

4 Press the † or … button to select Edit.

Press the

Result

ENTER () button.

: The Edit menu is displayed.

5 Press the † or … button to select Sort.

Press the

Result

ENTER () button.

: The Sort menu is displayed.

6 Select the channel that you wish to move by pressing the † or …

button. Press the ENTER () button.

7 Select the number of the programme to which the channel is to be

moved by pressing the Press the

Result

ENTER () button.

: The channel is moved to its new position and all other

channels are shifted accordingly.

† or … button.

Channel

group are

8 Repeat Steps 6 to 7 until you have moved all the channels to the

Prog.

----- ----- ----- -----

----- -----

Move Enter Return

Sort

required programme numbers.

Page 23

Assigning Names to Channels

Channel names will be assigned automatically when channel information is broadcast. These names can be changed, allowing you to assign new names.

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button to select Channel.

Result

The options available in the displayed.

3 Press the ENTER () button.

4 Press the † or … button to select Edit.

Press the

Result

ENTER () button.

: The Edit menu is displayed.

5 Press the † or … button to select Name.

Press the

Result

ENTER () button.

: The Name menu is displayed with the current channel

automatically is selected.

6 If necessary, select the channel to be assigned a new name by

pressing the

Result

† or … button. Press the ENTER () button.

: Arrow indications are displayed around the name box.

7 Press the † or … button to select a letter (A~Z), a number (0~9)

or a symbol ( pressing the

, space). Move on the previous or next letter by

œ or √ button.

Channel

group are

Country : Austria

Auto Store

Manual Store

Edit

Fine Tune

Ch. Scan

Move Enter Return

Add/Delete

Sort

Name

LNA : Off

Child Lock

Move Enter Return

Prog. Name

----- -----

Move Enter Return

ENG

Channel

√√ √√ √√ √√ √√ √√

Edit

√√ √√ √√ √√ √√

Name

8 When you have finished entering the name, press the ENTER ()

button to confirm the name.

Prog. Name

----- -----

Adjust Enter Return

Name

Page 24

ENG

Country : Austria

Auto Store

Manual Store

Edit

Fine Tune

Ch. Scan

Move Enter Return

Add/Delete

Sort

Name

LNA : Off

Child Lock

Move Enter Return

Add/Delete

Sort

Name

LNA : Off

Child Lock

Using the LNA (Low Noise Amplifier) Feature

This function is very useful in the situation that the TV is used in

Channel

√√ √√ √√ √√ √√ √√

Edit

√√ √√ √√ √√ √√

Edit

Off

weak signal. LNA amplifies the TV signal in the weak signal area, but not noise.

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button to select Channel.

Result

The options available in the

Channel

displayed.

3 Press the ENTER () button.

4 Press the † or … button to select Edit.

Press the

Result

ENTER () button.

: The Edit menu is displayed.

5 Press the † or … button to select LNA.

Press the

Result

ENTER () button.

: The options available are listed.

6 Select On or Off by pressing the † or … button.

➢

Press the

◆

ENTER () button to confirm.

If the picture is noisy with the LNA set to On, select Off.

LNA setting is to be made for each channel.

group are

Move Enter Return

Page 25

Activating the Child Lock

◆ Activating the child lock

This feature allows you to lock the television so that it cannot be switched on via the front panel. It can, however, still be switched on via the remote control. Thus, by keeping the remote control away from unauthorised users, such as children, you can prevent them from watching unsuitable programme.

1 Press the MENU button.

Result

: The main menu is displayed.

Country : Austria

Auto Store

Manual Store

Edit

Fine Tune

Ch. Scan

Move Enter Return

ENG

Channel

√√ √√ √√ √√ √√ √√

2 Press the † or … button to select Channel.

Result

The options available in the

displayed.

Channel

group are

3 Press the ENTER () button.

4 Press the † or … button to select Edit.

Press the

Result

ENTER () button.

: The Edit menu is displayed.

5 Press the † or … button to select Child Lock.

Press the

Result

ENTER () button.

: The Child Lock menu is displayed with the current

channel automatically is selected. Blue Screen is displayed when the

Child Lock is

activated.

6 Press the † or … button to select the channel to be locked.

7 Press the ENTER () button. To lock the channel, select

Locked by pressing the † or … button (to unlock the channel, select

Unlocked). Press the ENTER () button to confirm.

Add/Delete

Sort

Name

LNA : Off

Child Lock

Prog.

Edit

Move Enter Return

Child Lock

----- -----

Move Enter Return

----- -----

Child Lock

Unlocked Unlocked Unlocked Unlocked Unlocked

Unlocked Unlocked

Unlocked

Unlocked Unlocked

√√ √√ √√ √√ √√

Adjust Enter Return

Page 26

ENG

Displaying Information

You can view the channel information and setting status you select by pressing the “INFO

()

” button on the remote control.

P 1 ✽

Picture : Dynamic Sound : Music 00 : 00

Mode : Dynamic Custom Colour Tone : Normal

Colour Control

Film Mode : Off Size : 16 : 9 DNIe : On PIP

Move Enter Return

Mode : Dynamic

Custom Colour Tone : Normal

Colour Control

Film Mode : Off Size : 16 : 9 DNIe : On PIP

Move Enter Return

Mono

Changing the Picture Standard

You can select the type of picture which best corresponds to your

Picture

√√ √√ √√

√√

√√ √√ √√ √√

Picture

Dynamic

Standard

Movie

Custom

viewing requirements.

1 Press the MENU button.

: The main menu is displayed.

Result

2 Press the † or … button to select Picture.

Result

The options available in the displayed.

3 Press the ENTER () button.

: The Mode is selected

Result

4 Press the ENTER () button again.

Result

The options available are listed.

5 Select the option by pressing the † or … button.

: The following modes are available depending on the

Result

input source.

◆ Dynamic - Standard - Movie - Custom

◆ High - Middle - Low - Custom

(PC or DVI Mode)

Picture

group are

6 Press the ENTER () button to confirm.

You can also set these options simply by pressing the

➢

P.MODE (: Picture Mode) button.

Page 27

Adjusting the Picture Settings

Your television has several settings which allow you to control picture quality.

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button to select Picture.

Result

The options available in the displayed.

Picture

group are

Mode : Dynamic Custom Colour Tone : Normal

Colour Control

Film Mode : Off Size : 16 : 9 DNIe : On PIP

Move Enter Return

ENG

Picture

√√ √√ √√

√√

√√ √√ √√ √√

3 Press the ENTER () button.

4 Select the required option (Custom, Colour Tone) pressing the

† or … button.

5 Press the † or … button to select Custom.

Press the

Result

ENTER () button.

The

Custom

menu is displayed.

6 Press the ENTER () button to change the setting.

The options are displayed in the following order.

◆ Custom : Contrast , Brightness, Sharpness, Colour,

Tint(NTSC ONLY)

Custom Options available in PC, DVI Mode: Contrast,

➢

Brightness, Sharpness.

The horizontal bar is displayed. Move the horizontal bar’s

➢

cursor left or right by pressing the

When the picture mode is set to Custom, the settings values

➢

œ or √ button.

may vary depending on the input source. (ex. RF, Video, Component, PC or DVI)

If you make any changes to these settings, the picture

➢

standard is automatically switched to the

Custom.

◆ Colour Tone : Cool2 , Cool1, Normal, Warm1, Warm2

7 When you are satisfied with the settings, press the EXIT/TV ()

button to return to normal viewing.

Contrast 70

Brightness 50

Sharpness 70

Colour 50

Tint G50 R50

Move Enter Return

Contrast 70

Mode : Dynamic Custom

Colour Tone : Normal

Colour Control

Film Mode : Off Size : 16 : 9 DNIe : On PIP

Move Enter Return

Custom

Picture

Cool2

Cool1

Normal

Warm1

Warm2

If you make any changes to these settings, the picture

➢

standard is automatically switched to the

Custom.

Page 28

ENG

Adjusting the Picture Settings (PC or DVI Mode)

Preset to the PC or DVI mode by using the SOURCE button.

➢

Mode : High Custom Colour Tone : Custom Colour Control

Film Mode : Off

Size : 16 : 9 DNIe : On PIP

Move Enter Return

Contrast 70

Brightness 50

Sharpness 70

Colour 50

Tint G50 R50

Move Enter Return

Mode : High Custom

Colour Tone : Normal

Colour Control

Film Mode : Off

Size : 16 : 9 DNIe : On PIP

Move Enter Return

R70

G50

B70

Picture

√√ √√ √√ √√

√√

√√ √√ √√

Custom

Picture

Custom

Colour1

Colour2

Colour3

Colour Control

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button to select Picture.

Result

The options available in the

Picture

group are

displayed.

3 Press the ENTER () button.

4 Press the † or … button to select Custom.

Press the

Result

ENTER () button.

: The Custom menu is displayed.

5 Press the † or … button to select the option (Contrast,

Brightness, Sharpness) to be adjusted.

Press the

Result

ENTER () button.

: The horizontal bar is displayed. Move the horizontal

bar’s cursor left or right by pressing the

œ or √ button.

6 Press the MENU button to confirm your choice.

7 Press the MENU button.

Result

: The options available in the Picture group are

displayed again.

8 Press the † or … button to select Colour Tone.

Press the

ENTER () button.

9 Select the option by pressing the † or … button. The colour tones

are displayed in the following order.

Custom (PC mode only)- Colour1- Colour2- Colour3

10 Press the MENU button.

Result

: The options available in the Picture group are

displayed again.

Move Enter Return

11 Press the † or … button to select Colour Control.

Press the

Result

ENTER () button.

: The

Colour Control menu is displayed.

12 Press the † or … button to select the option (R, G, B) to be

adjusted. Press the

Result

: The horizontal bar is displayed. Move the horizontal

The Colour Control is not available in the DVI Mode.

➢

ENTER () button.

bar’s cursor left or right by pressing the

œ or √ button.

Page 29

Setting the Picture (PC Mode)

Preset to the PC mode by using the SOURCE button.

➢

ENG

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button to select Setup.

Result

: The options available in the Setup group are

displayed.

3 Press the ENTER () button.

4 Press the † or … button to select PC Setup.

Press the

Result

ENTER () button.

: The options available in the PC Setup group are

displayed.

5 Press the † or … button to select Image Lock.

Press the ENTER () button.

Result

: The options available in the Image Lock group are

displayed.

6 Press the † or … button to select the option (Coarse, Fine) to be

adjusted. Press the

Result

: The horizontal bar is displayed. Move the horizontal

ENTER () button.

bar’s cursor left or right by pressing the

œ or √ button.

7 Press the MENU () button to confirm your choice.

Time

Language : English

AV Setup

Digital NR : On

Miscellaneous

PC Setup

Move Enter Return

Image Lock

Position

Information

Auto Adjustment

Coarse 50

Fine 20

PC Setup

Move Enter Return

Image Lock

Setup

√√ √√ √√ √√ √√ √√

√√ √√ √√ √√

8 Press the MENU button.

Result

: The options available in the PC Setup group are

displayed again.

9 Press the † or … button to select Position.

Press the

Result

ENTER () button.

: The options available in the Position group are

displayed.

10 Adjust the position by using the †, …, œ or √ button.

11 Press the MENU () button to confirm your choice

Coarse

Move Enter Return

PC Setup

Image Lock

Position

Information

Auto Adjustment

Move Enter Return

Position

œœ √√

Move

Move Return

√√ √√ √√ √√

Page 30

ENG

Setting the Picture (PC Mode) (continued)

Preset to the PC mode by using the SOURCE button.

➢

Image Lock

Position

Information

Auto Adjustment

Move Enter Return

Resolution : 1024 ✻ 768

H-Frequency : 48.5KHz

V-Frequency : 60.2Hz

Image Lock

Position

Information

Auto Adjustment

PC Setup

Information

PC Setup

√√ √√ √√ √√

Return

√√ √√ √√ √√

12 If you get the PC information, select the Information by pressing

the

† or … button. Press the ENTER () button.

Result

: The resolution, horizontal and vertical frequency are

displayed.

13 Press the MENU button.

Result

: The options available in the PC Setup group are

displayed again.

14 Press the † or … button to select Auto Adjustment.

Press the

Result

ENTER () button.

: The screen quality and position are automatically reset

with the

Auto Adjusting displayed.

15 When you are satisfied with the settings, press the MENU ()

button repeatedly to return to the normal viewing.

Move Enter Return

Auto Adjustment

Auto Adjusting

Page 31

Using the Fine Tune

If reception is weak, you can fine tune a channel manually.

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button to select Channel.

Result

The options available in the displayed.

3 Press the ENTER () button.

4 Press the † or … button to select Fine Tune.

Press the

Result

ENTER () button.

: The horizontal bar is displayed. Move the horizontal

bar’s cursor left or right by pressing the

to reach the required setting.

Channel

group are

œ or √ button

Country : Austria

Auto Store

Manual Store

Edit

Fine Tune

Ch. Scan

Move Enter Return

P 1

Reset

Move

Channel

Fine Tune

Return

œœ √√

Adjust Store

ENG

√√ √√ √√ √√ √√ √√

5 Press the œ or √ button until the picture and sound are both clear

and sharp. Press the

ENTER () button.

6 To reset the fine tuning to 0, select Reset by pressing the † or …

button then press the ENTER () button.

If you are unable to fine tune a channel, check that the

➢

Colour System

Fine tune Store will change the colour of the Channel

➢

OSD(On Screen Display) from White to Red.

and

Sound System

settings are correct.

P 1

Move

P 1 is fine tuned

Move

P1 C11

Fine Tune

Reset

œœ √√

Adjust Store

Fine Tune

Reset

œœ √√

Adjust Store

Return

Page 32

ENG

Viewing the Channel Scan Picture

Country : Austria

Auto Store

Manual Store

Edit

Fine Tune

Ch. Scan

Move Enter Return

Ch. Scan

P 1 ✽

Channel

Return

1 Press the MENU button.

Result

√√ √√ √√ √√ √√ √√

2 Press the † or … button to select Channel.

: The main menu is displayed.

Result

The options available in the displayed.

Channel

group are

3 Press the ENTER () button.

4 Press the † or … button to select Ch. Scan.

Press the

Result

ENTER () button.

: You can view every memorized channel in order.

5 Press the MENU () button to exit.

When PIP ON is activated, the PIP will appear in Large

➢

mode and PIP channel will be scanned.

Freezing the Current Picture

You can freeze the picture when watching a television programme simply by pressing the “STILL” button. To return to normal viewing, press it again.

In the PIP mode, the main and sub pictures are stilled at

➢

the same time.

This function will automatically cancel after 5 minutes.

➢

Page 33

Selecting the Picture Size

You can select the picture size which best corresponds to your viewing requirements.

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button to select Picture.

Result

The options available in the displayed.

Picture

group are

Mode : Dynamic Custom Colour Tone : Normal

Colour Control

Film Mode : Off Size : 16 : 9 DNIe : On PIP

Move Enter Return

ENG

Picture

√√ √√ √√

√√

√√ √√ √√ √√

3 Press the ENTER () button.

4 Press the † or … button until the Size is selected.

Press the

ENTER () button

5 Press the † or … button to change the setting.

◆ Auto Wide : Expanding and pulling up the picture from 4:3 to

◆ 16:9 : Sets the picture to 16:9 wide mode.

◆ Panorama : Use this mode for the wide aspect ratio of a

◆ Zoom : Magnify the size of the picture vertically on

◆ 14:9 : Magnify the size of the picture more than 4:3.

◆ 4:3 : Sets the picture to 4:3 normal mode.

16:9 ratio.

panoramic picture.

screen.

6 Press the ENTER () button to confirm.

◆ You can select these options by simply pressing the

➢

Positioning and Sizing the screen using Zoom

➢

P.SIZE button on the remote control.

◆ The picture size can not be changed in the PIP mode.

◆ Depending on the input source, the P.SIZE options

may vary.

◆ Resizing the screen using the Zoom enables the positioning and sizing of the screen to up/down direction using the

†or…

button as well as the

screen size.

◆ Move the screen up/down using the †or…button after selecting the by pressing the

†or…

◆ Resize the screen vertically using the †or…button after selecting the by pressing the

†or…

◆ Screen enlargement operates only in TV/Video/ S-Video/Component1,2 input modes.

◆ PC/DVI modes prevents the screen enlargement function.

button.

Auto Wide

16:9

Panorama

Zoom

14:9

4:3

Move Enter Return

PC to DVI Mode

Auto Wide

16:9

Panorama

Zoom

14:9

4:3

Move Enter Return

Size

Page 34

ENG

Mode : Dynamic Custom Colour Tone : Normal

Colour Control

Film Mode : Off Size : 16 : 9 DNIe : On PIP

Move Enter Return

Selecting the Film Mode

You can automatically sense and process film signals from some

Picture

√√ √√ √√

√√

√√ √√ √√ √√

sources and adjust the picture for optimum quality.

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button to select Picture.

Result

: The options available in the Picture group are displayed.

3 Press the ENTER () button.

Mode : Dynamic Custom Colour Tone : Normal

Colour Control

Film Mode : Off

Size : 16 : 9 DNIe : On PIP

Move Enter Return

Mode : Dynamic Custom Colour Tone : Normal

Colour Control

Film Mode : Off Size : 16 : 9 DNIe : On PIP

Move Enter Return

Picture

4 Press the † or … button to select Film Mode.

Press the

ENTER () button.

5 Press the † or … button to change the setting (Off or On).

Off

◆ On : Automatically senses and processes film signals from some sources and adjusts the picture for optimum quality.

◆ Off : Switches off the Film Mode.

6 Press the ENTER () button to confirm.

◆

➢

Not available in the PC, Component (480P, 576P, 720P, 1080i) or DVI modes.

◆

Mode discrepancies, such as turning off Film Mode while viewing a film source or turning on Film Mode while viewing non-film sources, may affect the picture quality.

DNIeTM(Digital Natural Image engine)

This feature bring you more detailed image with 3D noise reduction, detail

Picture

√√ √√ √√

√√

√√ √√ √√ √√

enhancement, contrast enhancement and white enhancement. New image compensation Algorithm gives brighter, clearer, much detailed image to you.

DNIe

technology will fit every signals into your eyes.

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button until the Picture is selected.

Result

: The options available in the Picture group are

displayed.

Mode : Dynamic Custom Colour Tone : Normal

Colour Control

Film Mode : Off Size : 16 : 9

DNIe : On

PIP

Move Enter Return

Picture

Off

Demo

3 Press the ENTER () button.

4 Press the † or … button until the DNIe is selected.

Press the

ENTER () button.

5 Press the † or … button to change the setting.

◆ On : Switches on the DNIe mode.

◆ Off: Switches off the DNIe mode.

◆ Demo (Option): The screen before applying DNIe appears on

the right and the screen after applying DNIe appears on the left.

6 Press the ENTER () button to confirm.

Page 35

Setting the Blue Screen

If no signal is being received or the signal is very weak, a blue screen automatically replaces the noisy picture background. If you wish to continue viewing the poor picture, you must set the “

Blue Screen“ mode to “Off “.

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button to select Setup.

Result

: The options available in the Setup group are displayed.

3 Press the ENTER () button.

4 Press the † or … button to select Miscellaneous.

Press the ENTER () button.

Result

: The options available in the Miscellaneous group are

displayed.

5 Press the † or … button to select Blue Screen.

Press the ENTER () button.

6 Press the † or … button to change the setting (Off or On ).

7 Press the ENTER () button to confirm.

◆

➢

Blue Screen is displayed while no signal from the external device in the External Mode, regardless of the Blue Screen Setting.

Time

Language : English

AV Setup

Digital NR : On

Miscellaneous

PC Setup

Move Enter Return

Melody : Off

Plug & Play

Blue Screen : Off

Move Enter Return

Melody : Off

Plug & Play

Blue Screen : Off

Move Enter Return

Setup

ENG

√√ √√ √√ √√ √√

√√

Miscellaneous

√√ √√ √√

Miscellaneous

Off

Setting the Melody Sound

You can hear clear melody sound when the television is powered on or off.

1 Press the MENU button.

: The main menu is displayed.

Result

2 Press the † or … button to select Setup.

: The options available in the

Result

3 Press the ENTER () button.

4 Press the † or … button to select Miscellaneous.

Press the ENTER () button.

Result

: The options available in the Miscellaneous group are

displayed.

5 Press the † or … button to select Melody.

Press the ENTER () button.

6 Press the † or … button to change the setting (Off or On).

7 Press the ENTER () button to confirm.

Setup group are displayed.

Melody : Off

Plug & Play

Blue Screen : Off

Melody : Off

Plug & Play

Blue Screen : Off

Miscellaneous

√√ √√ √√

Move Enter Return

Miscellaneous

Off

Move Enter Return

Page 36

ENG

Mode : Dynamic Custom Colour Tone : Normal

Colour Control

Film Mode : Off Size : 16 : 9 DNIe : On PIP

Move Enter Return

Viewing the Picture In Picture (PIP)

You can display a sub picture within the main picture of TV program or external

Picture

√√ √√ √√

√√

√√ √√ √√ √√

A/V devices. In this way you can watch TV program or monitor the video input from any connected devices while watching TV or other video input.

1 Press the MENU button.

: The main menu is displayed.

Result

2 Press the † or … button to select Picture.

: The options available in the Picture group are displayed.

Result

3 Press the ENTER () button.

PIP : On

Source : TV

Swap

Size

Position

Prog. : P 8

PIP : On

Source : TV

Swap

Size

Position

Prog. : P08

PIP : On

Source : TV

Swap

Size

Position

Prog. : P 8

PIP

Off

Move Enter Return

PIP

Ext.1

Ext.2

Ext.3

AV1

AV2

†

Move Enter Return

PIP

√√

4 Press the † or … button to select PIP.

Press the ENTER () button.

Result

: The options available in the PIP group are displayed.

5 Press the ENTER () button again.

To activate, set the Press the

ENTER () button.

PIP to on by pressing the † or … button.

6 Press the † or … button to select Source.

Press the Result

ENTER () button.

: The sources are displayed in the following order:

TV - Ext.1 - Ext.2 - Ext.3 - AV1 - AV2 S-Video - Component1 - Component2 - PC - DVI

◆ The PC can not be selected in DVI mode.

➢

◆ The DVI can not be selected in PC mode.

7 Select a source of the sub picture by pressing the † or … button.

Press the ENTER () button.

8 Press the † or … button to select Swap.

Press the ENTER () button. Result

: The main picture and sub picture are interchanged.

9 Press the † or … button to select Size.

Press the ENTER () button.

Result

: The sizes are displayed in the following order:

(Large)

(Small) -(Double1) -(Double2)

PIP : On

Source : TV

Swap

Size

Position

Prog. : P08

Move Enter Return

PIP

Move Enter Return

10 Select a size of the sub picture by pressing the † or … button.

Press the ENTER () button.

Table of PIP Settings

Main

PIP

Ext.1 OXOOOO O O O OO Ext.2 OOX OOO O O O OO Ext.3 OOOXOO O O O OO AV1 OOOOXO O O O OO AV2 OOOOO X O O O OO S-Video Component1 Component2 PC OOOOOO O X X XX DVI OOOOOO O X X XX

TV Ext.1 Ext.2 Ext.3 AV1 AV2

OOOOOO O O O OO

OOOOOO X O O OO OOOOOO O X X XX OOOOOO O X X XX

X - This PIP combination is not available. O - This PIP combination is available.

S-Video Component1 Component2

PC DVI

Page 37

Viewing the Picture In Picture (PIP) (continued)

ENG

11 Press the † or … button to select Position .

Press the

Result

ENTER () button.

: The positions available are displayed.

---

12 Select a position by pressing the † or … button.

Press the

ENTER () button.

13 Press the † or … button to select Prog. .

Press the

ENTER () button.

14 Select the channel that you want to view through sub picture

by pressing the

If the sub picture is no signal and the main picture is

➢

output from a Component, PC or DVI signal, the sub picture will be blue. If the main picture is output from a Video signal, the sub picture will be black.

Easy functions of remote control.

Buttons Feature

† or … button. Press the ENTER () button.

PIP : On

Source : TV

Swap

Size

Position

Prog. : P08

PIP : On

Source : TV

Swap

Size

Position

Prog. : P08

PIP

Move Enter Return

PIP

P 1

Move Enter Return

PIP ON Used to activate or deactivate the PIP function directly.

SWAP Used to interchange the main picture and the sub

picture.

When the main picture is in the Video mode and

➢

the sub picture is in the TV mode, you might not hear the sound of main picture when pressing the SWAP () button after changing the sub picture channel. At this time, reselect the channel of main picture.

POSITION Used to move the sub picture counterclockwise.

SOURCE Used to assign a source of sub picture (TV, Ext.1,

Ext.2, Ext.3 , AV1, AV2 , S-Video, Component1, Component2, PC , DVI).

SIZE Used to select a size of sub picture (Large, Small,

Double1, Double2).

SCAN Used to scan every memorized channel in order.

To stop scanning, press it again.

P/ Used to select the channel of sub picture.

Page 38

ENG

Time

Language : English

AV Setup

Digital NR : On

Miscellaneous

PC Setup

Using the Digital NR (Digital Noise Reduction) Feature

If the signal received by your television is weak, you can activate

Setup

√√ √√ √√ √√ √√

√√

this feature to help reduce any static and ghosting that may appear on the screen.

1 Press the MENU button.

: The main menu is displayed.

Result

Move Enter Return

Time

Language : English

AV Setup

Digital NR : On

Miscellaneous

PC Setup

Move Enter Return

Setup

Off

2 Press the † or … button until the Setup is selected.

Result

The options available in the

Setup

group are displayed.

3 Press the ENTER () button.

4 Press the † or … button until the Digital NR is selected.

Press the

ENTER () button.

5 Select Off or On by pressing the † or … button.

Press the

ENTER () button to confirm.

Page 39

Changing the Sound Standard

You can select the type of special sound effect to be used when watching a given broadcast.

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button to select Sound .

Result

The options available in the

3 Press the ENTER () button.

Result

: The Mode is selected.

4 Press the ENTER () button again.

5 Select the option by pressing the † or … button. The sound

effects are displayed in the following order.

Standard- Music- Movie- Speech- Custom.

Sound

group are displayed.

Mode : Standard

Equalizer

Auto Volume : Off

SRS TSXT : Off

Internal Mute : Off

Move Enter Return

Mode : Standard

Equalizer

Auto Volume : Off

SRS TSXT : Off

Internal Mute : Off

ENG

Sound

√√ √√ √√ √√ √√

Sound

Standard

Music

Movie

Speech

Custom

6 Press the ENTER () button to confirm.

You can also set these options simply by pressing the

➢

S.MODE (: Sound Mode) button.

Move Enter Return

Page 40

ENG

Mode : Standard

Equalizer

Auto Volume : Off

SRS TSXT : Off

Internal Mute : Off

Adjusting the Sound Settings

The sound settings can be adjusted to suit your personal preferences.

Sound

√√ √√ √√ √√ √√

1 Press the MENU button.

: The main menu is displayed.

Result

2 Press the † or … button to select Sound.

Result

The options available in the

Sound

group are displayed.

Move Enter Return

Adjust√√Move Return

Mode : Standard

Equalizer

Auto Volume : Off

SRS TSXT : Off

Internal Mute : Off

Move Enter Return

Mode : Standard

Equalizer

Auto Volume : Off

SRS TSXT : Off

Internal Mute : Off

3 Press the ENTER () button.

4 Press the † or … button to select Equalizer.

Equalizer

Press the Result

ENTER () button.

: The Equalizer menu is displayed with the current

option.

5 Select the option (volume, balance, equalizer) to be adjusted by

pressing the required setting.

100 300 1K 3K 10K

œ or √ button. Press the † or … button to reach the

6 When you are satisfied with the settings, press the MENU ()

button to store them.

If you make any changes to the equalizer settings, the

➢

sound standard is automatically switched to the

Adjusting the Volume Automatically

Each broadcasting station has its own signal conditions, and so it

Sound

√√ √√ √√ √√ √√

Sound

Off

is not easy for you to adjust the volume every time the channel is changed. This feature lets you automatically adjust the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low.

1 Press the MENU button.

: The main menu is displayed.

Result

2 Press the † or … button to select Sound.

The options available in the

Result

3 Press the ENTER () button.

4 Press the † or … button to select Auto Volume.

Press the

ENTER () button.

Sound

group are displayed.

Custom.

Move Enter Return

5 Select the option (Off or On ) by pressing the † or … button.

6 Press the ENTER () button to confirm.

Page 41

Setting the TruSurround XT

TruSurround XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers. TruSurround delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal television speakers. It is fully compatible with all multichannel formats.

1 Press the MENU button.

: The main menu is displayed.

Result

2 Press the † or … button until the Sound is selected.

Result

The options available in the

3 Press the ENTER () button.

4 Press the † or … button until the SRS TSXT is selected.

Press the

ENTER () button.

5 Press the † or … button to change the setting (Off

Stereo).

6 Press the ENTER () button to confirm.

Sound

group are displayed.

3D Mono or

Mode : Standard

Equalizer

Auto Volume : Off

SRS TSXT : Off

Internal Mute : Off

Move Enter Return

Mode : Standard

Equalizer

Auto Volume : Off

SRS TSXT : Off

Internal Mute : Off

Move Enter Return

ENG

Sound

√√ √√ √√ √√ √√

Sound

Off

3D Mono

Stereo

TruSurround XT, SRS and ( ) Symbol

➢

are trademarks of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc.

You can also set these options simply by pressing the

➢

SRS TSXT ()button.

Selecting the Internal Mute

If you want to hear the sound through separate speakers, cancel the internal amplifier.

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button to select Sound.

Result

The options available in the

3 Press the ENTER () button.

4 Press the † or … button to select Internal Mute.

Press the

ENTER () button.

5 Press the † or … button to change the setting (Off or On).

6 Press the ENTER () button to confirm.

Sound

group are displayed.

Mode : Standard

Equalizer

Auto Volume : Off

SRS TSXT : Off

Internal Mute : Off

Move Enter Return

Mode : Standard

Equalizer

Auto Volume : Off

SRS TSXT : Off

Internal Mute : Off

Move Enter Return

Sound

√√ √√ √√ √√ √√

Sound

Off

Page 42

ENG

Selecting the Sound Mode (depending on the model)

The “DUAL I-II” button displays/controls the processing and output of the audio signal. When power is switched on, the mode is automatically preset to either “DUAL-I ” or “Stereo”, depending on the current transmission.

Type of broadcast

Regular broadcast

(Standard audio)

Regular +

NICAM

Stereo

◆ If the receiving conditions deteriorate, listening will be

➢

◆ If the stereo signal is weak and an automatic switching

◆ When receiving a mono sound in the AV mode, connect

NICAM Mono

NICAM Stereo

NICAM DUAL-I/II

Regular broadcast

(Standard audio)

Bilingual or DUAL-I/II

Stereo

easier if the mode is set to the

occurs, then switch to the

to the “AUDIO-L” input connector on the side of the television. If the mono sound comes out only from left speaker, press the

DUAL I-II button.

On-screen indication

(Normal use)

Mono

NICAM Mono↔Mono

NICAM Stereo↔Mono

NICAM DUAL-I

NICAM DUAL-II

Mono

DUAL-

I↔DUAL-II

Stereo↔Mono

Mono.

(Forced mono)

→

(Forced mono)

Page 43

Setting the Sleep Timer

You can select a time period of between 30 and 180 minutes after which the television automatically switches to Standby mode.

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button to select Setup.

Result

: The options available in the Setup group are

displayed.

3 Press the ENTER () button.

4 Press the † or … button to select Time.

Press the

Result

5 Press the † or … button to select Sleep Timer.

Press the

Result

ENTER () button.

: The options available in the Time group are displayed.

ENTER () button.

: The Sleep Timer menu is displayed with the Min is

selected.

Time

Language : English

AV Setup

Digital NR : On

Miscellaneous

PC Setup

Move Enter Return

Clock 00 : 00

Sleep Timer Off

On Timer Off

Off Timer Off

Move Enter Return

ENG

Setup

√√ √√ √√ √√ √√

√√

Time

√√ √√ √√ √√

6 Select the preset time intervals (Off, 30 , 60 , 90, 120, 150, 180) by

pressing the

† or … button.

7 Press the œ or √ button to move to the Activation.

8 When you are satisfied with the settings, select Activation to

Yes or No by pressing the † or … button.

9 Press the ENTER () button to confirm your selection.

◆

➢

You can also set these options simply by pressing the SLEEP button.

◆

If the sleep timer is not yet set,

Off

is displayed. If the sleep timer is already set, the remaining time before which the television switches to Standby mode is displayed.

Sleep Timer

Min Activation

Adjust√√Move Return

Min Activation

30 Yes

Adjust

Sleep Timer

œœ √√

Move Return

Off

Page 44

ENG

Time

Language : English

AV Setup

Digital NR : On

Miscellaneous

PC Setup

Move Enter Return

Clock 00 : 00

Sleep Timer Off

On Timer Off

Off Timer Off

Move Enter Return

Setting and Displaying the Current Time

You can set the television’s clock so that the current time is displayed

Setup

√√ √√ √√ √√ √√

√√

Time

√√ √√ √√ √√

Clock

by pressing the “INFO ( )” button. You must also set the time if you wish to use the automatic on or off timers.

When pressing the “I / ” button (On/Off) on the front of

➢

the television, the clock setting will be reset.

1 Press the MENU button.

: The main menu is displayed.

Result

2 Press the ▼ or ▲ button to select Setup.

: The options available in the Setup group are

Result

displayed.

3 Press the ENTER () button.

4 Press the ▼ or ▲ button to select Time.

Press the Result

ENTER () button.

: The options available in the Time group are displayed

with

Clock is selected.

5 Press the ENTER () button.

6 Press the ¦ or button to move to the hour or minute.

Set the hour or minute by pressing the

▼ or ▲ button.

Hour Min

01 00

Adjust√√Move Return

7 When you have finished, press the MENU () button to exit.

8 Press the INFO () button to display the current time.

Page 45

Switching the Television On and Off Automatically

You can set the television’s clock and set the On or Off timers so that the television will:

◆ Switch on automatically and tune to the channel of your choice at the time you select

◆ Switch off automatically at the time you select

The first step is to set the television’s clock (refer to

➢

“Setting and Displaying the Current Time” on the previous page).

1 Press the MENU button.

: The main menu is displayed.

Result

2 Press the ▼ or ▲ button to select Setup.

: The options available in the Setup group are

Result

displayed.

3 Press the ENTER () button.

Setup

Time

Language : English

AV Setup

Digital NR : On

Miscellaneous

PC Setup

Move Enter Return

Time

Clock 00 : 00

Sleep Timer Off

On Timer Off

Off Timer Off

ENG

√√ √√ √√ √√ √√

√√

√√ √√ √√ √√

4 Press the † or … button to select Time.

Press the Result

ENTER () button.

: The options available in the Time group are displayed.

5 Press the ▼ or ▲ button to select On Timer.

Press the Result

ENTER () button.

: The options available in the On Timer group are

displayed.

6 Select the Hour, Min , Prog., Volume by pressing the œ or √

button. Set these by pressing the † or … button.

7 Press the œ or √ button to move to the Activation.

8 When you are satisfied with the settings, select Activation to

Yes or No by pressing the † or … button.

9 Press the MENU button.

: The options available in the Time group are displayed

Result

again.

10 Press the † or … button to select Off Timer.

Press the Result

ENTER () button.

: The Off Timer menu is displayed.

11 Select the Hour, Min or Activation by pressing the œ or √

button. Set these by pressing the † or … button.

12 Press the ENTER () button to confirm.

Move Enter Return

On Timer

Hour Min Prog.

00 00 1

Volume Activation

10 No

Adjust√√Move Return

Off Timer

Hour Min

00 00

Activation

Adjust√√Move Return

Absent Power Off

➢

When you set the timer “On”, your television will eventually be turned off, if you do not operate any controls during the 3 hours after the TV is turned on by timer. This function is available in only the timer “On” mode and will prevent a leakage accident or overheating, caused by your TV left on for a long time due to the timer “On” (when you are away on holiday, for example).

If no signal is received for 15 minutes, the TV will be

➢

automatically turned off.

Page 46

ENG

Source List : TV

Edit Name

Viewing an External Signal Source

Use the remote control to switch between viewing signal from

Input

√√ √√

connected equipment, such as VCR, DVD, Set-Top-boxs and the TV source (broadcast or cable)

1 Press the MENU button.

Result

: The main menu is displayed.

Ext.1 Ext.2 Ext.3 AV1 AV2 S-Video ▼ More

Source List : TV

Edit Name

Ext.1 :

Ext.2 : Ext.3 : AV1 : AV2 : S-Video : Component1 : ▼ More

Move Enter Return

Source List

----

Move Enter Return

Input

√√ √√

Move Enter Return

Edit Name

----

VCR

DVD

Cable STB

HD STB

----

Satellite STB

†

Move Enter Return

2 Press the ▼ or ▲ button to select Input.

Result

: The options available in the Input group are

displayed.

3 Press the ENTER () button.

4 Press the ▼ or ▲ button to select Source List.

Press the

Result

ENTER () button.

: The options available in the Source List group are

displayed.

5 Press the ▼ or ▲ button to select signal source, then press the

ENTER () button.

➢ When you connect equipment to the TV, you can choose

between the following sets of jacks : AV1, AV2 , S-Video, Component1 , Component2, PC or DVI on the TV’s rear panel.

6 Press the MENU button and select Input.

7 Press the ▼ or ▲ button to select Edit Name.

Press the

Result

ENTER () button.

: The options available in the Edit Name group are

displayed.

8 Press the ▼ or ▲ button to select external device :

Ext.1 - Ext.2 - Ext.3 - AV1 - AV2 - S-Video Component1 - Component2 - PC - DVI

9 Press the ENTER () button.

The

Result

Edit Name

available are listed

10 Select the name by pressing the † or … button.

Press the

ENTER () button.

Ext.1, Ext.2 , Ext.3,

11 Set other signal sources (VCR , DVD, Cable STB, HD STB,

Satellite STB, AV Receiver, DVD Receiver, Game, Camcorder, DVD Combo, DHR or PC) using the same method as

listed above.

You can also set these options simply by pressing the

➢

SOURCE ()button. If you change the external source while viewing, pictures might take a short period of time to be switched.

DHR : DVD HDD Recorder

➢

Page 47

Redirecting an Input to the External Output

Your television enables you to choose which audio/video signals are output to the external connector.

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button to select Setup.

Result

: The options available in the Setup group are

displayed.

Time

Language : English

AV Setup

Digital NR : On

Miscellaneous

PC Setup

Move Enter Return

ENG

Setup

√√ √√ √√ √√ √√

√√

3 Press the ENTER () button.

4 Press the † or … button to select AV Setup.

Press the

Result

ENTER () button.

: The AV Setup menu is displayed.

5 Press the † or … button to select required input (Ext.2 or Ext.3).

Select the source to be directed to the output by pressing the

… button.

† or

6 Press the ENTER () button to confirm the change.

AV Setup

Ext.1 : TV

Ext.2 : TV

Ext.3 : TV

Move Enter Return

AV Setup

Ext.1 : TV

Ext.2 : TV

Ext.3 : TV

Move Enter Return

Ext.1

Ext.2

Ext.3

AV1

AV2

†

√√

√√ √√

Page 48

ENG

Teletext Feature

Most television channels provide written information services via teletext. Information provided includes:

This information is divided into numbered pages (see diagram).

◆

Television programme times

◆

News bulletins and weather forecasts

◆

Sports results

◆

Travel information

Part Contents

A Selected page number.

B Broadcasting channel identity.

C Current page number or search indications.

D Date and time.

EText.

F Status information.

FASTEXT information.

Teletext information is often divided between several

➢

pages displayed in sequence, which can be accessed by:

◆ Entering the page number

◆ Selecting a title in a list

◆ Selecting a coloured heading (FASTEXT system)

Page 49

Displaying the Teletext Information

You can display Teletext information at any time on your television

For Teletext information to be displayed correctly,

☛

channel reception must be stable; otherwise:

◆ Information may be missing

◆ Some pages may not be displayed

1 Select the channel providing the Teletext service by pressing the

P or button.

2 Press the TTX/MIX () button to activate the teletext mode.

Result

The contents page is displayed. It can be redisplayed at any time by pressing the (index) button.

3 Press the TTX/MIX () button again.

Result

4 If you wish to display the actual broadcast and teletext information

on a single screen, press the

5 To exit from the teletext display, press the EXIT/TV () button.

The screen will be split into two. This Double Teletext feature lets you view the information separately on the screen.

actual broadcast

TTX/MIX ()button again.

and teletext

ENG

Page 50

ENG

Selecting Display Options

When you have displayed a Teletext page, you can select various options to suit your requirements.

To display... Press the...

◆ Hidden text (reveal) (answers to quiz games, for example)

◆ The normal screen (reveal) again

◆ A secondary page by entering its number (sub-page)

◆ The broadcast when searching for a page (cancel)

◆ The next page (page up)

◆ The previous page (page down)

◆ Double-size letters in the: (size)

• Upper half of the screen • Once

• Lower half of the screen • Twice

◆ The normal screen • Three times

Page 51

Selecting a Teletext Page

You can enter the page number directly by pressing the numeric buttons on the remote control.

1 Enter the three-digit page number given in the content by

pressing the corresponding numeric buttons.

Result

: The current page counter is incremented and the

page is then displayed. If the selected page is linked with several secondary pages, the secondary pages are displayed in sequence. To freeze the display on a given page, press the (hold). Press it again to resume.

2 If the FASTEXT system is used by the broadcasting company,

the different topics covered on a Teletext page are colour-coded and can be selected by pressing the coloured buttons on the remote control. Press the coloured button corresponding to the topic that you wish to select; the available topics are given on the status line.

Result

: The page is displayed with other coloured information

that can be selected in the same way.

3 To display the previous or next page, press the corresponding

coloured button.

ENG

4 To display the subpage, see the following steps.

◆

Press the (sub-page) button. Result

: The available subpages appear.

◆

Select the required sub-page. Sub-pages can be scrolled by pressing the or button.

5 When you have finished, press the EXIT/TV () button to

return to your normal broadcast.

Page 52

ENG

Time Language : English AV Setup Digital NR : On Miscellaneous

PC Setup

TeleWeb

TeleWeb Feature (Option)

TeleWeb is the new television broadcasting standard for Teletext

Setup

√√ √√ √√ √√ √√

√√

services. TeleWeb is similar to Teletext, just easy to use. TeleWeb can transmit the News, TV programme information, and advertising in excellent picture quality and directly access via the remote control.

1 Press the MENU button.

Result

: The main menu is displayed.

Move Enter Return

TeleWeb

TeleWeb : On

Provider Search

Provider Select

Download : Off

Move Enter Return

TeleWeb

TeleWeb : On

Provider Search

Provider Select

Download : Off

Move Enter Return

Provider Search

Provider store in progress

Stop

Enter Return

TeleWeb

TeleWeb : On

Provider Search

Provider Select

Download : Off

Move Enter Return

TeleWeb

TeleWeb : On

Provider Search

Provider Select

Download : Off

Move Enter Return

Off

C11

P 9

2 Press the † or … button to select Setup.

: The options available in the Setup group are displayed.

Result

3 Press the ENTER () button.

4 Press the † or … button to select TeleWeb.

Press the Result

ENTER () button.

: The TeleWeb menu is displayed.

5 To activate the TeleWeb feature, set the TeleWeb to On by

pressing the

◆

If you set to On, 400 teletext pages can be stored.

◆

If you set to Off, 2100 teletext pages can be stored.

√√ √√

√√

6 Press the † or … button to select Provider Search. Start the

provider search by pressing the Result

œ or √ button.

: It will be search only the channels stored. If it find a

provider, the Added is displayed and continue the search.

➢ To stop the search before it has finished, press the EXIT/TV

() button.

7 When the search has been finished, press the † or … button to

select

Provider Select. Find the required provider by pressing

the

œ or √ button.

➢ Select a provider and then the TeleWeb downloading will

start.

8 Press the TeleWeb button to enter the TeleWeb mode.

√√ √√ √√ √√

9 If you want to download the TeleWeb information before switch

the television off, select the button. Press the œ or √ button to set to On.

: Even though you turn off the TV on the channel no

Result

provider is selected, the channel will be automatically switched to the selected channel and TeleWeb downloading will start. During downloading, the picture will not be shown and only status bar will be displayed on the screen. (It takes 30 minutes to one hour depending on the program.)

◆ When pressing the “

➢

panel of the television, the existing downloaded information will disappear.

◆ If you enter the TeleWeb mode on the channel where no provider is selected, you can view only the information downloaded up to now.

Download by pressing the † or …

I /

” button (On/Off) on the

Page 53

Using the TeleWeb Menu after Displaying the TeleWeb

Bookmarking the current page.

1 On the page you wish to add to the bookmark list press the

MENU button.

: The TeleWeb menu is displayed.

Result

2 Press the † or … button to select Add Bookmark.

Press the

Result

➢

ENTER () button.

: The current page is added to the bookmark list.

You can register up to six pages. If you add another URL when six bookmarks have been listed, the first URL will be deleted and the new URL will be listed as the sixth.

Bookmark List

Add Bookmark

Home Page

Current programme.

Selected provider.

Service is loading.

Move Add Exit

ENG

TeleWeb

√√

TeleWeb

Entering the bookmarked URL.

1 Press the MENU button.

: The TeleWeb menu is displayed with the Bookmark

Result

List

is selected.

2 Press the ENTER () button.

: The stored URLs are listed.

Result

3 To erase a URL, select a required URL and press the TeleWeb

(red) button.

Result

: The selected URL is erased and the listed URLs

moves up one by one.

4 Select the URL you wish to enter by pressing the † or … button

and press the

Result

Opening the Home Page

ENTER () button.

: The current page moves to the selected URL and the

menu is disappeared.

1 Press the MENU button.

Result

: The

TeleWeb menu is displayed.

2 Press the † or … button to select Home Page.

Press the

Result

ENTER () button.

: It moves to a home page.

Bookmark List

Add Bookmark

Home Page

Current programme. ----

Selected provider. ----

Service is loading.

Move Enter Exit

Bookmark List

SAMSUNG ELECTRONICS

TARA SYSTEMS

KIA MOTORS

MICRONAS

OLYMPIC NEWS

ECONOMICS

Move Delete Exit

TeleWeb

Bookmark List

Add Bookmark

Home Page

Current programme. ----

Selected provider. ----

Service is loading.

Move Enter Exit

√√

Page 54

ENG

Easy Accessing the TeleWeb Service via the Remote Control

Button Function

TeleWeb Activate or deactivate the TeleWeb feature directly.

Display the forward page of the TeleWeb

Display the backward page of the TeleWeb

Select a option.

Confirm your choice.

Page 55

Connecting to the External Devices

“MONITOR OUT” are used for the equipment with an RGB output, such as video game devices or video disc players.

ENG

Rear of the TV

(Input/Output)

①

VCR

②

DVD

Decoder /

Video game device

Video disc player

Satellite receiver

③

①

This end can be fitted with:

◆ A SCART connector

◆ Three RCA connectors (VIDEO + AUDIO-L/R)

②

If you have a second VCR and wish to copy cassettes tape, connect the source VCR to

EXT.3, AV1 or AV2) “EXT.1(EXT.2, EXT.3, AV1 or AV2)”

③

When you wish to record a programme, connect the receiver to and the VCR to

or AV2)

”

“MONITOR OUT”

Input/Output Specification

Connector

EXT.1 ✔✔ ✔✔ Only TV output is available.

EXT.2 ✔✔ ✔ Output you can choose.

EXT.3 ✔✔ ✔ Output you can choose.

”

and the target VCR to

“MONITOR OUT”

Video Audio (L/R) S-Video RGB Video + Audio (L/R)

so that you can redirect the signal from

“MONITOR OUT”

Input Output

so that you can redirect the signal from

“EXT.1(EXT.2, EXT.3, AV1 or AV2)”

“EXT.1(EXT.2, EXT.3, AV1

“EXT.1(EXT.2,

Page 56

ENG

Connecting to the S-Video Input

The S-VIDEO and RCA (AUDIO-L/R) connectors are used for equipment with an S-Video output, such as a camcorder or VCR.

Rear of the TV

①

and

①

To play picture and sound, both the S-VIDEO and RCA connectors must be used.

Whenever you connect an audio or video system to your television,

☛

ensure that all elements are switched off. Refer to the documentation supplied with your equipment for detailed connection instructions and associated safety precautions.

Camcorder

VCR

Page 57

Connecting to the DVI Input

The “DVI” (video) and “L-AUDIO-R” connectors are used for equipment with a DVI output.

ENG

Rear of the TV

Connecting to the PC Input

Personal Computer

and

The “RGB” (video) and “AUDIO” connectors are used for interfacing with your PC.

Rear of the TV

Personal Computer

and

Page 58

ENG

Connecting to the Component Input

Rear of the TV

①

The “COMPONENT 1” connectors are used for equipment with a DVD output. (480i/480P/576i/576P/720P/1080i)

②

The “COMPONENT 2” connectors are used for DTV receiver. (480i/480P/576i/576P/720P/1080i)

①

DVD

DTV receiver

②

Page 59

Connecting and Using the Home Theater System

Use the Monitor Out ports of the PDP for Home Theater System Connections.

Rear of the TV

Connecting the Home Theater System

①

Connect the monitoring audio out L, and R jacks of the MONITOR OUT on the rear-side connection panel of the PDP TV to the AUDIO IN jacks of the DVD Home Theater System (or AV Receiver) using the audio cable.

②

Press the SOURCE button to select the desired external device connected to the PDP TV.

③

If you want to hear the sound through separate speakers, cancel the internal amplifier.

ENG

①

DVD Home Theater

◆ Refer to corresponding user’s manual from the manufacturer for wiring the

☛

To Display the DVD Home Theater

Turn the PDP on and press the SOURCE button to select the Ext.1 (or Ext.2, Ext.3).

Be sure to connect the video cable properly if desired external input (Ext.1, Ext.2, or Ext.3) cannot be selected.

Play the DVD after activating the DVD Home Theater System.

Use the volume control of the Home Theater System while watching the PDP using the DVD Home Theater, where the PDP TV does not produce the audio.

speakers to the DVD Home Theater System (or AV Receiver).

◆ Disable the PDP TV internal speaker to enjoy the rich sound through the speakers of your Home Theater System.

◆ In this case, enjoy the sound from the Home Theater System while the PDP TV does not produce the audio.

②

AV Receiver Amplifier

Page 60

ENG

Setting up Your PC Software (Windows only)

The Windows display-settings for a typical computer are shown below. But the actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card. But even if your actual screens look different, the same, basic set-up information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)

On the windows screen, select in the following sequence:

Start ➞ Settings ➞ Control Panel.

When the control panel screen appears, click on Display and a display dialog-box will appear.

Select the Settings tab in the display dialog-box.

The two key variables that apply the television-PC interface are “Resolution” and “Colours”. The correct settings for these two variables are:

◆ Size (sometimes called “Resolution”)

1024 x 768 pixels

◆ Colour

32-bit colour Shown at left is a typical screen for “Display” dialog box.

If a vertical-frequency option exists on your display settings dialog box, the correct value is Otherwise, just click

OK and exit the dialog box.

60 Hz.

Page 61

Input Mode (PC/DVI)

Both screen position and size will vary depending on the type of PC monitor and its resolution. The table below shows all of the display modes that are supported:

ENG

Video Signal

IBM PC / AT

Compatible

◆ The interlace mode is not supported.

◆ The television might operate abnormally if a non-standard video format is selected.

Dot x Line

640 x 350

640 x 400 720 x 400

640 x 480

800 x 600

848 x 480

1024 x 768

Vertical

frequency (Hz)

70.086

85.080

70.087

85.039

59.940

72.809

75.000

85.008

56.250

60.317

72.188

75.000

85.061

60.000

72.000

75.000

60.004

70.069

75.029

84.997

Horizontal

frequency (kHz)

31.469

37.861

31.469

37.927

31.469

37.861

37.500

43.269

35.156

37.879

48.077

46.875

53.674

29.838

36.072

37.650

48.363

56.476

60.023

68.677

Vertical polarity

N N P P P N N N N

N/P

P P P P

nVidia chipset

N N P P

(N: Negative / P: Positive)

Horizontal

polarity

P P N N N N N N N

N/P

P P P P

N N P P

Notes

◆ The PC text quality for PS-37S4A is optimum in XGA mode (1024 x 768@60Hz).

◆ When this television is used as a PC display, 32-bit colour is supported.

◆ Your PC display screen might appear different depending on the manufacturer (and your particular version of

Windows). Check your PC instruction book for information about connecting your PC to a television.

◆ If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 48.3kHz (horizontal). In some cases, abnormal signals (such as stripes) might appear on the screen when the PC power is turned off (or if the PC is disconnected). If so, press the that the PC is connected.

◆ When connecting a notebook PC to the television, make sure that the PC screen is displayed through only the television (Otherwise, random signals might appear).

◆ When horizontal synchronous signals seem irregular in PC mode, check PC power saving mode or cable connections.

◆ The Display Settings Table above complies to the IBM/VESA standards, and based on the analog input.

◆ The DVI support mode is regarded as same to the PC support mode.

◆ The best timing for the vertical frequency to each mode is 60Hz.

SOURCE button to enter the Video mode. Also, make sure

Page 62

ENG

Pin Configurations

SCART Connector (EXT.1/EXT.2/EXT.3)

Pins 5, 7, 9, 11, 13, 15 and 16 are used for RGB processing and are

➢

only wired on the

EXT.1 or EXT.3 connector.

Pin Signal

1 Audio output R 2 Audio input R 3 Audio output L 4 Audio chassis return 5 Video chassis return (RGB blue) 6 Audio input L 7 RGB blue input 8 Switching voltage

9 Video chassis return (RGB green) 10 AV-Link (Ext 1) 11 RGB green input

PC Input Connector (15Pin)

Pin PC IN

1 Red (R)

2 Green (G)

3 Blue (B)

4 Grounding

5 Grounding (DDC)

6 Red (R) Grounding

7Green (G) Grounding

8 Blue (B) Grounding

9 Reserved 10 Sync Grounding 11 Grounding 12 Data (DDC) 13 Horizontal sync. 14 Vertical sync. 15 Clock (DDC)

Pin Signal

12 13 Video chassis return (RGB red) 14 15 RGB red input 16 Blanking signal (RGB switching) 17 Video chassis return 18 Blanking signal ground 19 Video output 20 Video input 21 Screening/chassis return

DVI Input Connector (24Pin)

Pin Signal

1T.M.D.S. Data22 T.M.D.S. Data2+ 3 T.M.D.S. Data2/4 Shield 4T.M.D.S. Data45 T.M.D.S. Data4+ 6 Clock (DDC) 7Data (DDC) 8 Not Connected

9T.M.D.S. Data110 T.M.D.S. Data1+ 11 T.M.D.S. Data1/3 Shield 12 T.M.D.S. Data313 T.M.D.S. Data3+ 14 +5V Power 15 5V Grounding 16 Hot Plug Detect 17 T.M.D.S. Data018 T.M.D.S. Data0+ 19 T.M.D.S. Data0/5 Shield 20 T.M.D.S. Data521 T.M.D.S. Data5+ 22 T.M.D.S. Clock Shield 23 T.M.D.S. Clock+ 24 T.M.D.S. Clock-

Page 63

Troubleshooting: Before Contacting Service Personnel

Before contacting Samsung after-sales service, perform the following simple checks.

If you cannot solve the problem using the instructions below, note the model and serial number of the television and contact your local dealer.

ENG

No sound or picture

Normal picture but no sound

No picture or black and white picture

Sound and picture interference

Blurred or snowy picture, distorted sound

Remote control malfunctions

◆ Check that the mains lead has been connected to a wall socket.

◆ Check that you have pressed the “ I ” button (On/Off) and the

POWER () button.

◆ Check the picture contrast and brightness settings.

◆ Check the volume.

◆ Check whether the volume MUTE () button on the remote control

has been pressed.

◆ Adjust the colour settings.

◆ Check that the broadcast system selected is correct.

◆ Try to identify the electrical appliance that is affecting the television,

then move it further away.

◆ Plug your television into a different mains socket.

◆ Check the direction, location and connections of your aerial.

This interference often occurs due to the use of an indoor aerial.

◆ Replace the remote control batteries.

◆ Clean the upper edge of the remote control (transmission window).

◆ Check the battery terminals.

Page 64

ENG

Programming the Remote Control for Other Components

CABLE CODE LIST

Anvision 017, 018

GI 041

Hamlin 003, 024, 031

Hitachi 025, 030

Jerrold 038, 039

Macom 025, 030

Magnavox 019, 023, 028

Oak 026

Panasonic 003, 022, 027, 037, 044

Samsung

JVC

PROSCAN, RCA

Panasonic

LG(Goldstar)

Sony

Denon

Curtis Mathes

Philips 019, 021, 023, 028

Pioneer 018, 020, 004, 044

RCA 014, 022, 040

Regal 003

Regency 015, 023

SA 042, 043

Samsung 000, 001, 002, 003, 004, 005, 006, 007

Scientific Atlanta 042, 043

Sprucer 022

Stargate 2000 036

Sylvania 016

Texscan 016

Tocom 032

Universal 033, 034

Viewstar 019, 021,023, 028

Wamer amex 046

Zenith 017, 029, 035, 037, 045

DVD CODE LIST

000

001

002

003

005

006

007

008

009

Page 65

Programming the Remote Control for Other Components (continued)

VCR CODE LIST

ENG

Admiral 020 Aiwa 025 Akai 027, 004, 032 Audio Dynamics 007, 026 Bell&Howell 018 Broksonic 022 Candle 002, 006, 003, 015, 008, 055 Canon 021, 056 Citizen 002, 006, 003, 015, 008, 055 Colortyme 007 Craig 002, 024 Curtis Mathes 002, 017, 007, 008, 021, 025, 056, 064, 066 Daewoo 003, 015, 010, 011, 012, 013, 014, 016 DBX 007, 026 Dimensia 017 Dynatech 034 Emerson 001, 003, 006, 021, 022, 025, 030, 032, 034,

040, 047, 050, 052, 060, 063, 065, 066, 067, 069 Fisher 018, 024, 028, 029, 048, 051, 061 Funai 025 General Electric 017, 002, 021, 005, 056 Go Video 002 LG(Goldstar) 006, 007, 008, 009, 010 Harman Kardon 007 Hitachi 019, 025, 041, 042 Instant Replay 021 JC Penny 002, 007, 018, 019, 021, 026, 037, 041, 054, 056 JVC 007, 008, 018, 021, 026, 037 Kenwood 007, 008, 018, 026, 037 KLH 070 Lioyd 025 Logik 038 LXI 025 Magnavox 021, 036, 056, 059 Marantz 018, 021, 007, 026, 037, 008, 062, 036 Marta 006 MEI 021 Memorex 006, 021, 024, 025 MGA 034 Midland 005 Minolta 019, 041 Mitsubishi 019, 034, 041, 046 Montgomery Ward 020 MTC 002, 025 Multitech 002, 025, 038, 005

NEC 018, 007, 026, 037, 008, 062, 064 Optimus 020 Panasonic 021, 056, 071, 072 Pentax 019, 041 Pentex Research 008 Philco 021, 036, 056, 059 Philips 021, 036 Pioneer 019, 026, 039, 053 Portland 015, 049, 055 PROSCAN 017 Quartz 018 Quasar 021, 056 Radio Shack/Realistic 006, 018, 020, 021, 024,

RCA 017, 019, 002, 021, 035, 041, 043, 057, 068 Samsung 000, 001, 002, 003, 004, 005 Sansui 026 Sanyo 018, 024 Scott 003, 047, 052, 067 Sears 018, 019, 006, 024, 028, 029, 041, 048, 051 Sharp 020, 034, 045, 015 Shimom 027, 033, 038, 058 Signature 025 Sony 027, 033, 044 Sylvania 021, 025, 036, 056, 059 Symphonic 025 Tandy 018, 025 Tashika 006 Tatung 037 Teac 025, 037, 068 Technics 021 Teknika 021, 006, 025, 031 TMK 066 Toshiba 003, 019, 029, 051, 052 Totevision 002, 006 Unitech 002 Vector Research 007, 026 Victor 026 Video Concepts 007, 026 Videosonic 002 Wards 002, 003, 006, 019, 020, 021, 024,

Yamaha 007, 008, 018, 026, 037 Zenith 023, 027, 033, 073

025, 029, 034, 048, 056

025, 034, 038, 041

Page 66

AFTER SALES SERVICE

Do not hesitate to contact your retailer or service agent if a change in the performance of your product indicates that a faulty condition may be present.

ELECTRONICS

BN68-00700A-00

Samsung PS-37S4A User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

User Instructions

Checking Parts

Contents

Your New Plasma Display Panel

Infrared Remote Control

Inserting the Batteries in the Remote Control

Assembling the Stand-Base

Installing the Display on the Wall Attachment Panel

Connecting to an Aerial or Cable Television Network

Connecting a Satellite Receiver or Decoder

Switching On and Off

Placing in Standby Mode

Becoming Familiar with the Remote Control

Setting Up Your Remote Control

Plug & Play Feature

Choosing Your Language

Storing Channels Automatically

Storing Channels Manually

Skipping Unwanted Channels

Sorting the Stored Channels

Assigning Names to Channels

Using the LNA (Low Noise Amplifier) Feature

Activating the Child Lock

Displaying Information

Changing the Picture Standard

Adjusting the Picture Settings

Adjusting the Picture Settings (PC or DVI Mode)

Setting the Picture (PC Mode)

Using the Fine Tune

Viewing the Channel Scan Picture

Freezing the Current Picture

Selecting the Picture Size

Selecting the Film Mode

DNIeTM(Digital Natural Image engine)

Setting the Blue Screen

Setting the Melody Sound

Viewing the Picture In Picture (PIP)

Using the Digital NR (Digital Noise Reduction) Feature

Changing the Sound Standard

Adjusting the Sound Settings

Adjusting the Volume Automatically

Setting the TruSurround XT

Selecting the Internal Mute

Selecting the Sound Mode (depending on the model)

Setting the Sleep Timer

Setting and Displaying the Current Time

Switching the Television On and Off Automatically

Viewing an External Signal Source

Redirecting an Input to the External Output

Teletext Feature

Displaying the Teletext Information

Selecting Display Options

Selecting a Teletext Page

TeleWeb Feature (Option)

Using the TeleWeb Menu after Displaying the TeleWeb

Easy Accessing the TeleWeb Service via the Remote Control

Connecting to the External Devices

Connecting to the S-Video Input

Connecting to the DVI Input

Connecting and Using the Home Theater System

Setting up Your PC Software (Windows only)

Pin Configurations

Troubleshooting: Before Contacting Service Personnel

Programming the Remote Control for Other Components