Samsung PNM-9085RQZ, PNM-9084RQZ User Manual

NETWORK CAMERA

User Manual

PNM-9084RQZ/PNM-9085RQZ

Network Camera

User Manual

Hanwha Techwin

Trademark

Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company.

Restriction

Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.

Disclaimer

Hanwha Techwin

provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. right to change the contents of this document without prior notice.

Design and specications are subject to change without prior notice.

The initial administrator ID is “admin” and the password should be set when logging in for the rst time.

Please change your password every three months to safely protect personal information and to prevent the damage of the information theft. Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.

makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be

Co., Ltd. All r ights reser ved.

Hanwha Techwin

reserves the

overview

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.

(Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.)

7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/ accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lighting storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated from 12 Vdc, 3.2 A or PoE(55 Vdc), 0.77 A. (PNM-9084RQZ)

16. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated from 12 Vdc, 3.5 A or PoE(55 Vdc), 0.82 A. (PNM-9085RQZ)

17. Do not use DC power and HPoE injector at the same time.

18. This product is intended to be supplied by isolation power.

19. If you use excessive force when installing the product, the camera may be damaged and malfunction.

If you forcibly install the product using non-compliant tools, the product may be damaged.

20. Do not install the product in a place where chemical substances or oil mist exists or may be generated. As edible oils such as soybean oil may damage or warp the product, do not install the product in the kitchen or near the kitchen table. This may cause damage to the product.

21. When installing the product, be careful not to allow the surface of the product to be stained with chemical substance. Some chemical solvents such as cleaner or adhesives may cause serious damage to the product’s surface.

22. If you install/disassemble the product in a manner that has not been recommended, the production functions/ performance may not be guaranteed. Install the product by referring to “Installation & connection” in the user manual.

23. Installing or using the product in water can cause serious damage to the product.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT.

Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance with the installation instructions.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION

: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

● OVERVIEW

English _3

overview

Class construction

An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection.

Battery

Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

Disconnection Device

Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location.

When used outside of the U.S., it may be used HAR code with fittings of an approved agency is employed.

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

ATTENTION

IL Y A RISQUE D’EXPLOSION SI LA BATTERIE EST REMPLACÉE PAR UNE BATTERIE DE TYPE INCORRECT. METTRE AU REBUT LES BATTERIES USAGÉES CONFORMÉMENT AUX INSTRUCTIONS.

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

Please use the input power with just one camera and other devices must not be connected.

The ITE is to be connected only to PoE networks without routing to the outside plant.

The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE

802.3bt shall be a UL Listed device with the output evaluated as a Limited Power Source as defined in UL60950-1.

Unit is intended for installation in a Network Environment 0 as defined in IEC TR 62102. As such, associated Ethernet wiring shall be limited to inside the building.

Please read the following recommended safety precautions carefully.

yDo not place this apparatus on an uneven surface. yDo not install on a surface where it is exposed to direct sunlight, near heating equipment or

heavy cold area. yDo not place this apparatus near conductive material. yDo not attempt to service this apparatus yourself. yDo not place a glass of water on the product. yDo not install near any magnetic sources. yDo not block any ventilation openings. yDo not place heavy items on the product. yPlease wear protective gloves when installing/removing the camera.

The high temperature of the product surface may cause a burn. yDo not adjust or move the lens directly with your hands. Doing so could damage the lens or

degrade its performance. yThe life expectancy of driving the lens motor is 200 rotations. yTo move the location of your camera, privacy masking needs to be reset.

User’s Manual is a guidance book for how to use the products. The meaning of the symbols are shown below.

yReference : In case of providing information for helping of product’s usages yNotice : If there’s any possibility to occur any damages for the goods and human caused by

not following the instruction

 Please read this manual for the safety before using of goods and keep it in the safe place.

WARNING

To Prevent damage which may caused by IR LED, don't stare at operating lamp.

For below models only.

PNM-9084RQZ/PNM-9085RQZ

4_ overview

Risk Group 1

WARNING IR emitted from this product.

Do not stare at operating lamp.

Product tested against IEC 62471

CONTENTS

OVERVIEW

INSTALLATION & CONNECTION

NETWORK CONNECTION AND

SETUP

3 Important Safety Instructions 6 Product Features 6 Recommended PC Specifications 6 Recommended Micro SD/SDHC/SDXC

Memory Card Specifications

7 What’s Included 8 Optional Accessories for Installation 8 At a Glance

10 Installation 16 Connecting with other Device

19 Connecting the Camera Directly to Local

Area Networking

19 Connecting the Camera Directly to a DHCP

Based DSL/Cable Modem

20 Using Device Manager 20 Automatically searching camera 20 Configuring IP address 21 Manually registering camera 21 Automatically configuring IP 22 Port Range Forward (Port Mapping) Setup 23 Connecting to the Camera from a Shared

Local PC

23 Connecting to the Camera from a Remote

PC via the Internet

WEB VIEWER

APPENDIX

24 Connecting to the Camera 25 Password setting 25 Login 25 Camera Web Viewer Setup

26 Specification 28 Product Overview 29 Troubleshooting 30 Open Source Announcement

● OVERVIEW

English _5

overview

PRODUCT FEATURES

• 4-way Camera Each of the four camera lenses monitors a different direction.

• Dustproof/Waterproof The dust-resistant/water-resistant design protects the product from rain and dust when installed outdoors.

(IP66)

• IR mode If the IR indicator turns on, the product switches to the IR mode for preventing an object from being too bright,

which helps you identify the object in near distance.

• Supports 5M resolution videos (PNM-9085RQZ)

• Multi-Streaming This network camera can display videos in different resolutions and qualities simultaneously using different

CODECs.

• Web Browser-based Monitoring Using the Internet web browser to display the image in a local network environment.

• Alarm When an event occurs, related images are sent to the user’s registered e-mail and FTP server, stored on the micro

SD memory card, or signaled to the alarm output terminal.

• Tampering Detection Detects tempering attempts on video monitoring.

• Defocus detection function Detects the defocus phenomenon of the camera lens.

• Motion Detection Detects motion from the camera’s video input.

• Fog detection Detects fog that is heavier than the detection level.

• Face Detection Detects faces in the specified area from the camera’s video input.

• IVA (Intelligent Video Analysis) function Detects a motion or situation that meets the configured event rules.

• ONVIF Compliance This product supports ONVIF Profile S/T.

For more information, refer to www.onvif.org.

RECOMMENDED PC SPECIFICATIONS

• CPU : Intel(R) Core(TM) i7 3.4 GHz or higher

• RAM : 8G or higher

• Supported OS : Windows 7, 8.1, 10, Mac OS X 10.13

• Recommended browser : Google Chrome

• Supported browsers : MS Explore11, MS Edge, Mozilla Firefox(Window 64bit only), Apple Safari(Mac OS X only)

• VGA : PCIe 256MB GDDR3 video graphics card or higher Please see the appendix for detailed information on verified OS and browsers.



Some functions may be restricted even in supported browsers.

RECOMMENDED MICRO SD/SDHC/SDXC MEMORY CARD SPECIFICATIONS

• Recommended capacity : 16GB ~ 256GB(MLC type)

• Recommended Manufacturers : SanDisk, Transcend

• Product Type : High endurance

• The compatibility varies depending on the card manufacturers and types.

• It is recommended to use a memory card of 16GB or more that conforms to the UHS-3 class (MLC type)

specification.

6_ overview

WHAT’S INCLUDED

Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.)

Appearance Item Name Quantity Description

Cable bush

Spare bushes for Lan cables or alarm & audio cables.

● OVERVIEW

Camera 1

Quick Guide

(Optional)

LAN PoE

PoE INJECTOR

ACTIVE

POWER

HPoE injector 1

Audio/alarm cable 1 Used to connect with the audio and alarm port

Connects power supply and network

Template 1 Product installation guide

Power Terminal Block 1 Plugged in the power plug

CAUTION: Be ware of the Rated Voltage and Polarity

of the power connection.

Power Cable 1 Used to plug into the power port

Machine Screws 4

Screws used for mounting your camera on the

hanging mount, GangBox, etc.

Cap Installer 1 Used to connect the RJ45 cable.

Drill bit 1

Used for dome cover disassembly, assembly and camera installation.

English _7

overview

OPTIONAL ACCESSORIES FOR INSTALLATION

You can purchase appropriate optional accessories available.

Product type Wall mount

Model Name SBP-390WMW2

Product type Hanging mount Ceiling mount

Model Name SBP-317HMW SBP-300CMW

Product type Corner mount Pole mount

Model Name SBP-300KMW SBP-300PMW

AT A GLANCE

Appearance

Dome cover

Item Description

Case cover used to protect the lens and the main unit.

8_ overview

Camera body

Mount plate

Body part where the camera lens and connection terminals are included.

Plate that fixes the camera when mounting it to the ceiling or attaching it to a separately sold mount.

Components

b c d

Item Description

Cables

Audio and alarm cable port

Power Port

Color - CH 1: Red

ARM-IN Used to connect the alarm input sensor or external day/night sensor.

ARM-OUT Used to connect the alarm output signal.

GND These are common ports to connect alarm input/output signals.

MIC Used to connect to a microphone.

SPEAKER Used to connect to speakers.

Port for power terminal block.

CH 2: Green CH 3: Blue CH 4: Black

● OVERVIEW

Lens

Illumination Sensor

Micro SD Memory Card

Compartment

IR LED

Reset Button

HPoE Connection port

4 camera lenses show different directions.

Detects incoming light to control the IR LED.

Compartment for the Micro SD memory card.

These infrared LED’s are controlled by the illumination sensor.

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.

If you reset the camera, the network settings will be adjusted so that DHCP can be

enabled. If there is no DHCP server in the network, you must run the Device Manager program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network.

This terminal connects power and network via HPoE injector or connects to network via ethernet cable.

English _9

installation & connection

INSTALLATION

This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are

recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.

Precautions before installation

Ensure you read out the following instructions before installing the camera:

• Select an installation site that can hold at least 5 times the camera’s weight.

• Stuck-in or peeled-off cables can cause damage to the product or a fire.

• For safety purposes, keep anyone else away from the installation site. And put aside personal belongings from the site, just in case.

• If the product is installed with excessive force, it may cause damage to the camera due to malfunction. Forcing assembly using non-compliant tools may damage the product.

Disassembling

1. Remove the dome cover by loosening the fastening bolt of the

dome cover. This can be done by turning it counterclockwise using the drill bit provided.

Dome cover

2. Loosen the fastening screw on the camera body.

Do not adjust or move the lens directly with your hands. Doing so could

damage the lens or degrade its performance.

3. Remove the camera body and mounting plate by pulling the plate spring, as shown in the figure.

10_ installation & connection

Inserting a Micro SD Memory Card

1. Remove the dome cover of the camera.

2. Insert a Micro SD card in the arrow direction shown in the figure.

Disconnect the power cable from the camera before inserting the Micro SD memory card.

Do not forcefully insert it in the reverse direction. It might damage your Micro SD memory card and your product.

When it rains or the humidity is high, insertion or ejection of a Micro SD card is not recommended.

Disassembly of the product cover should be finished within 5 minutes, or there will be the risk of internal dew condensation.

If your camera's IR LED blocks the Micro SD slot, access the web viewer and move the lens not to block the slot.

Removing a Micro SD Memory Card

Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot.

You should save an SD card for each channel.

Please note that if you firmly push and release the Micro SD memory card when it is ejected, it may pop out.

Before removing the Micro SD memory card, in <Setup ( )>-<Event>-<Storage>, set the device to <Off> and press

the [Apply] button and turn the camera off.

If you turn off the camera or remove the Micro SD memory card that contains data from the product, the data may be lost or

damaged.

● INSTALLATION & CONNECTION

English _11

installation & connection

Installation (mount plate)

[Directly installing on ceiling]

1-1. Attach the installation template on the desired surface and drill

holes for screws and cables.

1-2. Fix the mount plate using appropriate screws.

1-3. Pull out necessary cables among Power / LAN / audio &

alarm cables through the hole in the mount plate.

[Installing using pipe]

2-1. Attach the installation template and drill holes for screws

and cables.

2-2. Separate the pipe cover of the mount plate by pressing its

sides.

2-3. Place the pipe on the mount plate.

2-4. Fix the mount plate using appropriate screws.

12_ installation & connection

2-5. Pull out necessary cables among Power / LAN / audio &

alarm cables through the pipe.

[Attaching to the unbundled adapter]

Choose and purchase a necessary one of the following options (unbundled) that is suitable to the installation site or for your convenience.

Installation (camera body and dome cover)

1. Connect the safety cable.

3-1. Install the hanging mount to the wall mount adapter.

Wall mount adapters and hanging mounts are sold separately.

3-2. Connect the mounting plate and the hanging mount.

2. Mount the camera body to the mount plate.

Mount it to fit the hinges as shown in the image.

3. Open the cable cover on the camera body.

4. Connect the terminals inside the camera with the necessary

cables, and then close the cable cover.

● INSTALLATION & CONNECTION

English _13

+ 28 hidden pages