PDP MONITOR
quick start guide
P42H, P50H, P42Hn, P50Hn
Introduction
Package Contents
Note
Please make sure the following items are included with your PDP Display. If any items are missing, contact your dealer.
Contact a local dealer to buy optional items.
Note
This stand is not for the Floor Standing Type.
Unpacking
PDP Display
Manuals
Quick Setup Guide |
Warranty Card |
User's Guide |
|
(Not available in all loca- |
|
|
tions) |
|
Cables
D-Sub Cable |
Power Cord |
Others
Introduction
Others |
|
|
Remote Control |
Batteries (AAA X 2) |
Ferrite Core for Power Cord |
|
(Not available in all loca- |
(3301-001110) |
|
tions) |
|
Sold separately |
|
|
DVI Cable |
Wall Mount KIT |
LAN Cable |
|
|
(Applicable to the P42HN / |
|
|
P50HN model only) |
TV tuner box |
NetWork Box |
Semi Stand KIT |
(Applicable to the P42H / P50H model only)
Note
•You can purchase and connect a separate network box or TV tuner box. For information on how to use these, refer to their respective user manuals.
•You can only connect one external box.
Ferrite Core (Power Cord)
•The ferrite cores are used to shield the cables from interference.
•When connecting a cable, open the ferrite core and clip it around the cable near the plug.
Introduction
Your PDP Display
Front
SOURCE button [SOURCE]
Switches from PC mode to Video mode. Changing the source is only allowed for external devices that are connected to the PDP Display at the time.
[PC] → [DVI] → [AV] → [HDMI] → [MagicInfo]
Note
•The TV menu is available when a TV tuner box is installed.
•The MagicInfo menu is available when a network box is installed in the HN or H model.
Enter button []
Activates a highlighted menu item.
MENU button [MENU]
Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu.
- VOL+
Moves from one menu item to another horizontally or adjusts selected menu values. When OSD is not on the screen, push the button to adjust volume.
SEL
Moves from one menu item to another vertically or adjusts selected menu values.
/ When OSD is not on the screen, push the button to adjust channel.
Power button []
Use this button for turning the PDP Display on and off.
Power indicator
Shows PowerSaver mode by blinking green
Introduction
Note
See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your PDP Display OFF when it is not needed or when leaving it unattended for long periods.
Remote Control Sensor
Aim the remote control towards this spot on the PDP Display.
Rear
Note
For detailed information concerning cable connections, refer to Connecting Cables under Setup. The PDP Display 's configuration at the back may vary slightly depending on the PDP Display model.
POWER IN
The power cord plugs into the PDP Display and the wall plug.
LAN (LAN Connection Terminal)
(Applicable to the P42HN / P50HN model only)
USB(USB Connection Terminal)
Keyboard / Mouse, Mass Storage Device Compatible.
(Applicable to the P42HN / P50HN model only)
Introduction
Note
The number of PDP Displays that can be connected to loopout may differ depending on the cables, signal source etc. With cables where there is no degradation or signal source, up to ten PDP Displays can be connected.
RS232C OUT/IN (RS232C Serial PORT)
MDC(Multiple Display Control) Program Port
DVI / PC / HDMI IN [DVI/PC/HDMI AUDIO IN] (PC/DVI/HDMI Audio Connection Terminal (Input))
DVI / PC / HDMI IN [HDMI]
Connect the HDMI terminal at the back of your PDP Display to the HDMI terminal of your digital output device using a HDMI cable.
DVI / PC / HDMI IN [RGB](PC Video Connection Terminal)
Using a D-Sub Cable (15 pin D-Sub) - PC mode (Analog PC)
DVI / PC / HDMI IN [DVI] (PC Video Connection Terminal)
Using a DVI Cable (DVI-D to DVI-D) - DVI mode (Digital PC)
DC Power [OUT]
Connect this to the POWER connector of a TV tuner box or network box.
AV IN [VIDEO]
Connect the [ VIDEO ] terminal of your monitor to the video output terminal of the external device using a VIDEO cable.
AV AUDIO IN [L- AUDIO - R]
Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the [ L- AUDIO - R ] port of the PDP Display.
Introduction
AUDIO OUT [L- AUDIO - R]
Headphone output terminal.
Kensington Lock
The Kensington Lock is a device used to physically fix the system when using it in a public place. The locking device has to be purchased separately. The appearance and locking method may differ from the illustration depending on the manufacturer. Refer to the manual provided with the Kensington Lock for proper use. The locking device has to be purchased separately.
Note
The location of the Kensington Lock may be different depending on its model.
Using the Anti-Theft Kensington Lock
1.Insert the locking device into the Kensington slot on the Monitor and turn it in the locking direction
.
2.Connect the Kensington Lock cable.
3.Fix the Kensington Lock to a desk or a heavy stationary object.
Note
See Connecting Cables for further information regarding cable connections.
Remote Control
Note
The performance of the remote control may be affected by a TV or other electronic device operating near the PDP Display , causing a malfunction due to interference with the frequency.