9. General Precaution ----------------------------------------------------------------------------------- (21)
9.1 Handling
9.2 Storage
9.3 Operation
9.4 Operation Condition Guide
9.5 Others
MODELLSJ460HQ02Doc. No06-000-G-20120730Page
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
2/24
www.panelook.com
Global LCD Panel Exchange Center
Revision History
DateRev. NoPageSummary
www.panelook.com
Samsung Secret
30. July.
2012
000allFirst issued
MODELLSJ460HQ02Doc. No06-000-G-20120730Page
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
3/24
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
General Description
Samsung Secret
Description
LSJ460HQ02 is a color active matrix liquid crystal display (LCD) that uses amorphous
silicon TFT( Thin Film Transistor) as switching components. This model is composed of a
TFT LCD panel, a driver circuit. The resolution of a 46“ is 1920 x 1080 and this model can
display up to 1.07 billion colors with wide viewing angle of 89¶ or higher in all directions.
This panel is intended to support applications to provide a excellent performance for Flat
Panel Display such as Home-alone Multimedia TFT-LCD TV and High Definition TV.
Features
High contrast & aperture ratio with wide color gamut
SVA (Super Vertical Align) mode
Wide viewing angle (·178¶)
High speed response
FHD resolution (16:9)
2Ch LVDS (Low Voltage Differential Signaling) interface
2D / 3D function compatible
General Information
ItemsSpecificationUnitNote
Panel Size
Weight2750gMax
Pixel Pitch0.17675(H) X 0.53025(V)mm
Active Display Area1018.08(H) X 572.67(V)mm
Surface TreatmentHaze 0%, Hard-coating (2H)
Display Colors1.07B (10 Bit)colors
Number of Pixels1920 x 1080pixel
Pixel ArrangementRGB vertical stripe
Display ModeNormally Black
1025.98(H
) x 580.57(V
TPY
1.80(D)
TPY
)
mm
·1.0mm
Max
MODELLSJ460HQ02Doc. No06-000-G-20120730Page
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
4/24
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Samsung Secret
1. Absolute Maximum Ratings
If the condition exceeds maximum ratings, it can cause malfunction or unrecoverable
damage to the device.
ItemSymbolMin.Max.UnitNote
(ڱ
ڮڮ ژٻڋٻڱڄ
Power Supply VoltageV
Storage temperatureT
Glass surface
temperature
(Operation)
CenterT
DD
STG
OPR
10.813.2V(1)
-2060
050
Note (1) Ta= 25 · 2 ¶C
(2) Temperature and relative humidity range are shown in the figure below.
a. 90 % RH Max. (Ta ≤ 39 ¶C)
b. Relative Humidity is 90% or less. (Ta > 39 ¶C)
c. No condensation
(2)
(2)
90
Fig. Temperature and Relative humidity range
MODELLSJ460HQ02Doc. No06-000-G-20120730Page
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
5/24
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
2. Optical Characteristics
The optical characteristics should be measured in a dark room or equivalent.
Measuring equipment :
ItemSymbolConditionMin.Typ.Max.UnitNote
Contrast Ratio
(Center of screen)
Response
Time
Color
Chromaticity
(CIE 1931)
G-to-GTg-412msec
Red
Green
Blue
D65,RD-80S,EZ-Contrast
C/R
Rx
Ry0.328
Gx0.281
Gy0.580
Bx0.133
By0.126
Normal
TL,R=0
TU,D=0
Viewing
Angle
3,0005,000-
TYP.
-0.03
(Ta = 25 · 2¶C, VDD=12V)
0.660
TYP. 0
+0.03
Samsung Secret
(1)
D65
(3)
RD-80S
(5),(6)
D65
White
Color gamut--66-%
Color Temperature--7,200-K
Hor.
Viewing
Angle
Ver.
Notice
(a) Test Equipment Setup
The measurement should be executed in a stable, windless and dark room between
40min and 60min after operating the Panel at the given temperature for stabilization
of the standard light(SEC use standard illuminant D65 Media).
This should be measured in the center of screen. Environment condition : Ta = 25 · 2 ¶C
Wx0.294
Wy0.361
T
L
T
R
T
U
T
D
C/R≥10
7589-
7589-
7589-
7589-
Degree
(5)
D65
(6)
EZ-
Contrast
(b) D65 Media means general available light source.
Color Temperature is 648704K , a color coordinate is Wx 0.313, Wy 0.329,
Luminance is 7217cd/༇
MODELLSJ460HQ02Doc. No06-000-G-20120730Page
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
6/24
www.panelook.com
Global LCD Panel Exchange Center
ྙ
ྚྛ
ྞ
ྡ
ྠ
ྜྷྜ
ྟ
www.panelook.com
Samsung Secret
Photo detectorField
SR3
RD-80S
TFT - LCD Module
- Definition of test point
1ദ
2ദ
Photo detector
Field
BM-5A : 50
RD-80S : 50
EZ-Contrast:0༃
LCD Panel
The center of the screen
3209601600
180
540
900
Note (1) Definition of Contrast Ratio (C/R)
: Ratio of gray max (Gmax) & gray min (Gmin) at the center point 䐣 of the panel
: The measurement goes in D65 Standard Light Source
/
CR
max
G
min
G
Gmax : Luminance with all pixels white
Gmin : Luminance with all pixels black
Active Area
Test Point
MODELLSJ460HQ02Doc. No06-000-G-20120730Page
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
7/24
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Note (2) Definition of 9 points Transmittance uniformity (Test pattern : Full White)
The measurement goes in D65 Standard Light Source
Samsung Secret
Tuni
TT
(max min)
T
max
u
100
Tmax : Maximum Transmittance
Tmin : Minimum Transmittance
Note (3) Definition of Response time : Sum of Tr, Tf
Display data
Optical Instruments
Response
100%
Black (data off)
T
R
White (data on)
90%
10%
0%
Black (data off)
T
F
G-to-G : Average response time between Gray to Gray (Scale)
Note (4) Definition of Transmittance : Transmittance at center point 䐣
The measurement goes in D65 Standard Light Source
Note (5) Definition of Color Chromaticity (CIE 1931)
Color coordinate of Red, Green, Blue & White at center point 䐣
The measurement goes in D65 Standard Light Source
Note (6) Definition of Viewing Angle
: Viewing angle range (C/R ≥10)
The measurement goes in D65 Standard Light Source
TIME
MODELLSJ460HQ02Doc. No06-000-G-20120730Page
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
8/24
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Samsung Secret
3. Electrical Characteristics
3.1 TFT LCD Module
The connector for display data & timing signal should be connected.
Ta = 25 ¶C · 2 ¶C
ItemSymbolMin.Typ.Max.UnitNote
Voltage of Power SupplyVDD10.812.013.2V(1)
Current
of Power
Supply
(a) Black
IDD
(c) N-pattern-7901000mA
-470550Ma
(2),(3)(b) White-490600mA
Vsync FrequencyfV95120125Hz
Hsync FrequencyfH120135140kHz
Main FrequencyFdclk260297305MHz
Rush CurrentIRUSH-46A(4)
Note (1) The ripple voltage should be controlled under 10% of V
(2) f
V= 120 Hz, fDCLK = 297 MHz, V
= 12.0V, DC Current.
DD
DD
.
(3) Power dissipation check pattern (LCD Module only)
a) Black Pattern b) White Pattern c) uT
(4) Measurement Conditions
V
100%
DD
90%
10%
GND
T
=470༕
RUSH
Rush Current I
can be measured when T
RUSH
. is 470༕.
RUSH
MODELLSJ460HQ02Doc. No06-000-G-20120730Page
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
9/24
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
5. Input Terminal Pin Assignment
Samsung Secret
5.1. Input Signal & Power
wzkwzk
X
Y
Z
[
\
]
^
_
`
XW
12VDC power supply
12VDC power supply
12VDC power supply
12VDC power supply
12VDC power supply
NCNOTE1
GNDGround
GNDGround
GNDGround
RO[0]NOdd LVDS Signal -
Y]
Y^
Y_
Y`
ZW
ZX
ZY
ZZ
Z[
Z\
RE[0]PEven LVDS Signal +
RE[1]NEven LVDS Signal -
RE[1]PEven LVDS Signal +
RE[2]NEven LVDS Signal -
RE[2]PEven LVDS Signal +
GNDGround
ROCLK-Even LVDS Clock -
ROCLK+Even LVDS Clock +
GNDGround
RE[3]NEven LVDS Signal -
Y\
XX
XY
XZ
X[
X\
X]
X^
X_
X`
YW
YX
YY
YZ
Y[
RO[0]POdd LVDS Signal +
RO[1]NOdd LVDS Signal -
RO[1]POdd LVDS Signal +
RO[2]NOdd LVDS Signal -
RO[2]POdd LVDS Signal +
GNDGround
ROCLK-Odd LVDS Clock -
ROCLK+Odd LVDS Clock +
GNDGround
RO[3]NOdd LVDS Signal -
RO[3]POdd LVDS Signal +
RO[4]NOdd LVDS Signal -, Note3
RO[4]POdd LVDS Signal +, Note3
GNDGround
RE[0]NEven LVDS Signal -
Z]
Z^
Z_
Z`
[W
[X
[Y
[Z
[[
[\
[]
[^
[_
[`
\W
RE[3]PEven LVDS Signal +
RE[4]NEven LVDS Signal -, Note3
RE[4]P
GNDGround
NC
NC
NC
NC
NC
LVDS_SELNOTE2
NC
NC
NC
NC
NC
Even LVDS Signal +,
Note3
NOTE1
\X
NCNOTE1
MODELLSJ460HQ02Doc. No06-000-G-20120730Page
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
10/24
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Samsung Secret
Note 1) NOT CONNECTED : THIS PINS ARE ONLY USED FOR SEC INTERNAL OPERATIONS.
Note 2) LVDS OPTION : IF THIS PIN : HIGH (3.3 V) → NORMAL NS LVDS FORMAT
OTHERWISE : LOW (GND) OR OPEN(NC) → JEIDA LVDS FORMAT
Note 3) IF LVDS 8Bit Input
Note 4) Pin number starts from Bottom side
PCB
Pin No. 1 Pin No. 51
#1
#1
Pin No. 1 Pin No. 41
#51
#51
#1#41
#1
#41
a. All GND pins should be connected together and also be connected to the LCD’s
metal chassis.
b. All power input pins should be connected together.
c. All NC pins should be separated from other signal or power.
MODELLSJ460HQ02Doc. No06-000-G-20120730Page
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
11/24
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
5.2 LVDS Interface
- LVDS Receiver : Tcon (merged) - Data Format (JEIDA)
LVDS pinVESA (Normal)JEIDA
TxIN/RxOUT0R0R4
TxIN/RxOUT1R1R5
TxIN/RxOUT2R2R6
TxOUT/RxINA
TxOUT/RxINB
TxIN/RxOUT3R3R7
TxIN/RxOUT4R4R8
TxIN/RxOUT6R5R9
TxIN/RxOUT7G0G4
TxIN/RxOUT8G1G5
TxIN/RxOUT9G2G6
TxIN/RxOUT12G3G7
TxIN/RxOUT13G4G8
TxIN/RxOUT14G5G9
Samsung Secret
TxOUT/RxINC
TxOUT/RxIND
TxIN/RxOUT15B2B4
TxIN/RxOUT18B3B5
TxIN/RxOUT19B4B6
TxIN/RxOUT20B5B7
TxIN/RxOUT21B6B8
TxIN/RxOUT22B7B9
TxIN/RxOUT24HsyncHsync
TxIN/RxOUT25VsyncVsync
TxIN/RxOUT26DEDE
TxIN/RxOUT27R6R2
TxIN/RxOUT5R7R3
TxIN/RxOUT10G6G2
TxIN/RxOUT11G7G3
TxIN/RxOUT16B6B2
TxIN/RxOUT17B7B3
TxIN/RxOUT23RESERVEDRESERVED
TxIN/RxOUT28R8R0
TxIN/RxOUT29R9R1
TxIN/RxOUT30G8G0
TxOUT/RxINE
TxIN/RxOUT31G9G1
TxIN/RxOUT32B8B0
TxIN/RxOUT33B9B1
TxIN/RxOUT34RESERVEDRESERVED
MODELLSJ460HQ02Doc. No06-000-G-20120730Page
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
12/24
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Samsung Secret
5.3 Input Signals, Basic Display Colors and Gray Scale of Each Color
Rn : Red Gray, Gn : Green Gray, Bn : Blue Gray (n = Gray level)
Input Signal : 0 = Low level voltage, 1 = High level voltage
MODELLSJ460HQ02Doc. No06-000-G-20120730Page
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
13/24
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
6. Interface Timing
6.1 Timing Parameters ( Timing-Controller )
SIGNALITEMSYMBOLMIN.TYP.MAX.UnitNOTE
Samsung Secret
ClockFrequency1/T
Frame
Frequency
Cycle
Active
Display
Vertical
Period
Display Term
Vertical
Total
Active
Display
Horizontal
Period
Display Term
Horizontal
Total
C
T
H
T
V
T
VD
T
VB
T
HD
T
H
260297305MHz
120135140kHz
95120125Hz
-1080-Lines
110011251350Lines
-1920-Clocks
209222002596clocks
2pixel/
Clock
Note) This product is DE only mode. The input of Hsync & Vsync signal does
not have an effect on normal operation.
(1) Test Point : TTL control signal and CLK at LVDS Tx input terminal in system
(2) Internal V
DD = 3.3V
(3) Spread spectrum
- Modulation rate (max) : · 1.5 %
- Modulation Frequency : 30 ~ 300KHz
MODELLSJ460HQ02Doc. No06-000-G-20120730Page
14/24
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
6.2 Timing diagrams of interface signal ( DE only mode )
TV
TVD
DE
TH
THD
Samsung Secret
DE
DCLK
DATA
SIGNALS
TC
MODELLSJ460HQ02Doc. No06-000-G-20120730Page
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
15/24
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
6.3 Power ON/OFF Sequence
To prevent a latch-up or DC operation of the LCD Module, the power on/off
sequence should be as the diagram below.
0.5ms<T1≤10ms
1ms<T2≤50ms
0ms<T3≤50ms
1000ms≤T4
Samsung Secret
1000ms≤T5
100ms≤T6
T1 : VDDrising time from 10% to 90%
T2 : The time from V
to valid data at power ON.
DD
T3 : The time from valid data off to VDDoff at power Off.
T4 : VDDoff time for Windows restart
T5 : The time from valid data to B/L enable at power ON.
T6 : The time from valid data off to B/L disable at power Off.
The supply voltage of the external system for the Module input should be the same
as the definition of VDD.
Apply the lamp voltage within the LCD operation range. When the back light turns on
before the LCD operation or the LCD turns off before the back light turns off,
the display may momentarily show abnormal screen.
In case of V
= off level,
DD
please keep the level of input signals low or keep a high impedance.
T4 should be measured after the Module has been fully discharged between power off
and on period.
Interface signal should not be kept at high impedance when the power is on.
MODELLSJ460HQ02Doc. No06-000-G-20120730Page
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
16/24
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
ACTIVE CENTER
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
8. PACKING
8.1 CARTON (Internal Package)
(1) Packing Form Corrugated fiberboard box and corrugated cardboard as shock absorber
(2) Packing Method
Packing- Upper Box
www.panelook.com
Samsung Secret
T
Pallet Tray
10EA
Pallet-Plastic
B
8.2 Packing Specification
ITEMSpecificationRemark
1. 2.00 Kg / LCD (15[ea]/Tray, 150[ea]/Pallet)
LCD Packing150ea / Box
2. 0.0194 Kg / Middle sheet (18[ea]/Tray, 180[ea]/Pallet)
3. 2.2 Kg / Panel tray (10ea/Pallet)
4. 0.56 Kg / Packing Box (1ea)
15EA
D
Pallet-Wood1Box / Pallet
Pallet sizeH x V x height1,200mm(H) x 1,000mm(V) x 1,230mm(height)
Pallet weight345.052 kg
MODELLSJ460HQ02Doc. No06-000-G-20120730Page
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
A nameplate bearing followed by is affixed to a shipped product at the specified
location on each product.
(1) Cell Label
LSJ460HQ02
Lot number : X X X X XXX
XX X
Cell Position No. (In the Glass)
Glass No. (In the one Lot)
Lot No. (Glass)
Month
Year (Note1)
Product code
Line
MODELLSJ460HQ02Doc. No06-000-G-20120730Page
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
19/24
www.panelook.com
Global LCD Panel Exchange Center
(2) Box Label
www.panelook.com
Samsung Secret
LSJ460HQ02
xxxx
150
MODELLSJ460HQ02Doc. No06-000-G-20120730Page
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
20/24
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
10. General Precautions
Samsung Secret
10.1 Handling
(a) When the Module is assembled, it should be attached to the system firmly
using all mounting holes. Be careful not to twist and bend the Module.
(b) Refrain from strong mechanical shock and / or any force to the Module.
In addition to damage, this may cause improper operation or damage to the Module
and CCFL back light.
(c) Note that polarizers are very fragile and could be damage easily.
Do not press or scratch the surface harder than a HB pencil lead.
(d) Wipe off water droplets or oil immediately. If you leave the droplets for a long
time, staining or discoloration may occur.
(e) If the surface of the polarizer is dirty, clean it using absorbent cotton or soft cloth.
(f) Desirable cleaners are water, IPA(Isopropyl Alcohol) or Hexane.
Do not use Ketone type materials(ex. Acetone), Ethyl alcohol, Toluene, Ethyl acid
or Methyl chloride. It might permanent damage to the polarizer due to chemical
reaction.
(g) If the liquid crystal material leaks from the panel, it should be kept away
from the eyes or mouth . In case of contact with hands, legs or clothes, it must
be washed away with soap thoroughly.
(h) Protect the module from Electrostatic discharge. Otherwise the ASIC IC or
Semiconductor would be damaged
.
(i) Use finger-stalls with soft gloves in order to keep display clean during the
incoming inspection and assembly process.
(k) Protection film for polarizer on the Module should be slowly peeled off just before use
so that the electrostatic charge can be minimized. Must put on antistatic glove while
handle a module
(l) Pins of I/F connector should not be touched directly with bare hands.
MODELLSJ460HQ02Doc. No06-000-G-20120730Page
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
21/24
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
* Process Control Standard
ItemManagement standard value and performance standard
1Anti-static mat (shelf)1 to 50 [Mohm]
2
3Ionizer
4Anti-static wrist band0.8 to 10 [Mohm]
5
Anti-static mat (floor,
desk)
Anti-static wrist band
entry and ground
resistance
1 to 100 [Mohm]
Attenuate from · 1,000V to · 100V within 2 sec
Below 1,000 [ohm]
Samsung Secret
6Temperature
0 35
7Humidity60 to 70 [%RH]
MODELLSJ460HQ02Doc. No06-000-G-20120730Page
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
22/24
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
10.2 Storage
We highly recommend to comply with the criteria in the table below
ITEMUnitMin.Max.
Storage
Temperature
Storage
Humidity
Storage life6 months
- The storage room should provide good ventilation and temperature control.
- Products should not be placed on the floor, but on the Pallet away from
- Prevent products from direct sunlight, moisture nor water; Be cautious of
Storage
Condition
- Avoid other hazardous environment while storing goods.
()540
(%rH)3575
a wall.
a build up of condensation.
Samsung Secret
After 1 month 2 month3 month4month5 month6month
Baking No backing50Ȕ+U50Ȕ+U
10.3 Operation
(a) Do not connect or disconnect the Module in the "Power On" condition.
(b) Power supply should always be turned on/off by the "Power on/off sequence"
(c) Module has high frequency circuits. Sufficient suppression to the electromagnetic
interference should be done by system manufacturers. Grounding and shielding methods
may be important to minimize the interference.
(d) The cable between the back light connector and its inverter power supply should
be connected directly with a minimized length. A longer cable between
the back light and the inverter may cause lower luminance of lamp(CCFT) and
may require higher startup voltage(Vs).
MODELLSJ460HQ02Doc. No06-000-G-20120730Page
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
23/24
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Samsung Secret
10.4 Operation Condition Guide
(a) The LCD product should be operated under normal conditions.
(b) If the product will be used in extreme conditions such as high temperature,
humidity, display patterns or operation time etc.., It is strongly recommended
to contact SEC for Application engineering advice. Otherwise, its reliability and
function may not be guaranteed. Extreme conditions are commonly found at
Airports, Transit Stations, Banks, Stock market, and Controlling systems.
10.5 Others
(a) Ultra-violet ray filter is necessary for outdoor operation.
(b) Avoid condensation of water. It may result in improper operation or disconnection
of electrode.
(c) Do not exceed the absolute maximum rating value. ( supply voltage variation,
input voltage variation, variation in part contents and environmental temperature,
and so on)
Otherwise the Module may be damaged.
(d) If the Module keeps displaying the same pattern for a long period of time,
the image may be "sticked" to the screen.
To avoid image sticking, it is recommended to use a screen saver.
(e) This Module has its circuitry PCB's on the rear side and should be handled
carefully in order not to be stressed.
(f) Please contact SEC in advance when you display the same pattern for a long time.
MODELLSJ460HQ02Doc. No06-000-G-20120730Page
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
24/24
www.panelook.com
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.