If you have any questions or comments relating to Samsung products,
please contact the SAMSUNG customer care centre.
Country
REPUBLIC OF IRELAND 0818 717 100 www.samsung.com/ie
U.K0870-SAMSUNG(726-7864)www.samsung.com/uk
Customer Care Centre
Web Site
LCD TV
LE40F8
LE46F8
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
BN68-01312A-00
ON-SCREEN MENUS
PC DISPLAY
PICTURE IN PICTURE (PIP)
TELETEXT
Register your product at www.samsung.com/global/register
Record your Model and Serial number here for future reference.
▪ Model _______________ ▪ Serial No. _______________
Page 2
Precautions When Displaying a Still Image
A still image may cause permanent damage to the TV screen.
WARNINGS:
Image retention, commonly known as screen burn-in, can occur on most types of television if the same
image is displayed continuously. The most common causes of image retention are logos that remain
stationary on the TV screen. These logos are common on many programmes received via a Setop Box.
To reduce this risk, avoid displaying still images for long durations and lower the brightness or contrast
settings to decrease the intensity of the picture. Extended viewing of movies and programs in aspect
ratios that are different from the aspect ratio of the TV may cause image retention. Always endeavour
to avoid black borders top or bottom by using the zoom function. This will help eliminate the black
borders and t the picture to the entire area of the screen. Using a video game console may cause
image retention and is not recommended. When using a PC input, avoid displaying still images for long
durations and reduce the brightness or contrast settings to decrease the intensity of the picture.
IMPORTANT:
Image retention issues are not covered by your Samsung® warranty.
• Do not display a still image on the LCD panel for more than 2 hours as it can cause screen image
retention. This image retention is also known as "screen burn".
To avoid such image retention, reduce the degree of brightness and contrast of the screen when
displaying a still image.
• Watching the LCD TV in 4:3 format for a long period of time may leave traces of borders
displayed on the left, right and center of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause a similar effect to the
screen. Damages caused by the above effect are not covered by the Warranty.
• Displaying still images from Video games and PC for longer than a certain period of time may produce
partial after-images. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still
images.
Listening through a Receiver ........................... 60
Check Points before Requesting Service ........ 60
SymbolPressImportantNoteOne-Touch
+
+ ..........................................
58
Button
English - 2
Page 5
List of Parts
Please make sure the following items are included with your LCD TV.
If any items are missing, contact your dealer.
Remote Control &
Batteries
(AAA x 2)
Owner’s Instructions
Registration Cards (Not available in all locations)
Power CordCover-BottomCleaning Cloth
Installing the Wall Mount Kit
Wall mount items (sold separately) allow you to mount
the TV on the wall.
For detailed information on installing the wall mount,
see the instructions provided with the Wall Mount items.
Contact a technician for assistance when installing the
wall mounted bracket.
Samsung Electronics is not responsible for any damage
to the product or injury to yourself or others
if you elect to install the TV on your own.
Do not install your Wall Mount Kit while your TV
is turned on. It may result in personal injury due
to electric shock
Remove the stand and cover the bottom hole with a
cap and fasten with two screws.
Registration Cards
English - 3
Page 6
Viewing the Control Panel
The product colour and shape may vary depending on the model.
Front Panel buttons
Touch the each button to
operate.
1 SOURCE Toggles between all the available input
sources (TV, Ext.1, Ext.2, AV, S-Video,
Component, PC, HDMI1, HDMI2, HDMI3,
DTV). In the on-screen menu, use this button
as you use the ENTER/OK button on the
remote control.
2 MENU Press to see an on-screen menu of your TV’s
features.
3 Press to decrease or increase the volume.
In the on-screen menu, use the buttons as you use the ◄ and ► buttons on
the remote control.
4 Press to change channels.
In the on-screen menu, use the buttons as you use the ▼ and ▲ buttons on
the remote control.
(Without the Remote Control, you can turn on
the TV by using the Channel buttons.)
English - 4
5 Power Indicator Blinks and turns off when the power is on and
lights up in stand-by mode.
6 Remote Control Sensor Aim the remote control towards this spot on
the TV.
7 Speakers
(Power)
8
Touch the silver sensor below the ( ) mark to
turn the TV on and off.
Silver sensor
Page 7
Viewing the Connection Panel
1234
[Side Panel Jacks]
5
3
6
8
7
#
Power Input
90!@
The product colour and shape may vary depending on the model.
Whenever you connect an external device to your TV, make sure that power on the unit is turned off.
When connecting an external device, match the colour of the connection terminal to the cable.
1 EXT 1, EXT 2
Connector
EXT 1
EXT 2
Video
o
o
Input
Audio (L/R)
o
o
RGB
o
Output
Video + Audio (L/R)
Only TV or DTV output is available.
Output you can choose.
-Inputs or outputs for external devices, such as VCR, DVD, video game device or video disc players.
2AUDIO OUT(R-AUDIO-L)
- Connect RCA audio cables to AUDIO OUT "R-AUDIO-L" on the rear of your set and the other ends to
corresponding audio in connectors on the Amplifier or DVD Home Theatre.
3 HDMI IN 1, HDMI IN 2, HDMI IN 3
- Supports connections between HDMI-connection-enabled AV devices (Set-Top Boxes, DVD players)
- No additional Audio connection is needed for an HDMI to HDMI connection.
- When using an HDMI/DVI cable connection, you must use the HDMI IN2 jack.
What is HDMI?
- “High Definition Multimedia interface” allows the transmission of high definition digital video data
and multiple channels of digital audio (5. 1 channels).
- The HDMI/DVI terminal supports DVI connection to an extended device with the appropriate cable
(not supplied). The difference between HDMI and DVI is that the HDMI device is smaller in size,
has the HDCP (High Bandwidth Digital Copy Protection) coding feature installed, and supports
multi - channel digital audio.
The TV may not output sound and pictures may be displayed with abnormal colour when DVD
players/Cable Boxes/Satellite receivers supporting HDMI versions older than 1.3 are connected. When
connecting an older HDMI cable and there is no sound, connect the HDMI cable to the HDMI IN 2 jack
and the audio cables to the DVI IN (HDMI2) "R-AUDIO-L" jacks on the back of the TV. If this happens,
contact the company that provided the DVD player/Cable Box/Satellite receiver to confirm the HDMI
version, then request an upgrade.
HDMI cables that are not 1.3 may cause annoying flicker or no screen display.
DVI IN (HDMI 2) (R-AUDIO-L)
- DVI audio outputs for external devices.
English - 5
Page 8
Supported modes for HDMI/DVI and Component
HDMI/DVI 50Hz
HDMI/DVI 60Hz
Component
480i
X
X
O
480p
X
O
O
576i
X
X
O
576p
O
X
O
720p
O
O
O
1080i
O
O
O
1080p
O
O
X
4 ANT IN
To view television channels correctly, a signal must be received by the set from one of the following
sources:
- An outdoor aerial / A cable television network / A satellite network
5
COMMON INTERFACE Slot
- When not inserting "CI CARD" in some channels,"Scrambled Signal" is displayed on the screen.
- The pairing information containing a telephone number, CI CARD ID, Host ID and other information
will be displayed in about 2~3 minutes. If an error message is displayed, please contact your
service provider.
- When the channel information configuration has finished, the message "Updating Completed" is
displayed, indicating that the channel list is now updated.
You must obtain a CI CARD from a local cable service provider.
Remove the CI CARD by carefully pulling it out with your hands since dropping the CI CARD
may cause damage to it.
Insert the CI-Card in the direction marked on it.
6 WISELINK
- Connect a USB mass storage device to view photo files (JPEG) and play audio files (MP3)
7 Headphones jack
- Headphone may be connected to the headphone output on your set. While the head phone is
connected, the sound from the built-in speakers will be disabled.
8
S-VIDEO or VIDEO / R-AUDIO-L
- Connect RCA or S-VIDEO cable to an appropriate external A/V device such as VCR, DVD or
Camcorder.
- Connect RCA audio cables to "R - AUDIO - L" on your set and the other ends to corre
sponding audio out connectors on the A/V device.
9PC IN (PC)/(AUDIO)
- Connect to the video and audio output jack on your PC.
0
DIGITAL AUDIO OUT (OPTICAL)
- Connect to a Digital Audio Component.
! SERVICE
- Connect this to the jack on the optional wall mount bracket. This will allow you to adjust the TV
viewing angle using your remote control.
@
COMPONENT IN
- Connect component video cables (optional) to component connector ("PR", "PB", "Y") on the rear of
your set and the other ends to corresponding component video out connectors on the DTV or DVD.
- If you wish to connect both the Set-Top Box and DTV (or DVD), you should connect the Set-Top Box
to the DTV (or DVD) and connect the DTV (or DVD) to component connector ("PR", "PB", "Y") on your
set.
- The PR, PB and Y connectors on your component devices (DTV or DVD) are sometimes labeled Y,
B-Y and R-Y or Y, Cb and Cr.
- Connect RCA audio cables (optional) to "R - AUDIO - L" on the rear of your set and the other ends to
corresponding audio out connectors on the DTV or DVD.
- This LCD TV displays its optimum picture resolution in 1080p mode.
- This LCD TV displays its maximum picture resolution in 1080p mode.
# Kensington Lock (depending on the model)
- The Kensington lock (optional) is a device used to physically fix the system when used in a public
place.
- If you want to use a locking device, contact the dealer where you purchased the TV.
- The place of the Kensington Lock may be different depending on its model.
English - 6
Page 9
Viewing the Remote Control
1 Selects a target device to be
controlled by the Samsung
remote control (TV, DVD,
STB, CABLE, VCR)(Refer to pages 43~46)
2 Television Standby button
3 Number buttons for direct
channel access
4
One/Two-digit channel
selection
5 It display "Channel List"
on the screen.
6 Selects the TV and DTV
mode directly
7 VCR/DVD Functions
Rewind, Stop, Play/Pause,
Fast/Forward
8 Volume increase
Volume decrease
9 Temporary sound switch-off
0 Displays the main on-screen
CH, and the active source
button(TV, DVD, CABLE, STB,
VCR) on the remote.
* Available source selection
( Previous channel
)
This function enables you to
view and play photo (JPEG)
and audio files (MP3) from an
external device.
a This remote can be used to
control recording on Samsung
recorders.
(Anynet+ function only)
b P
: Next channel
P : Previous channel
c Exit the on-screen menu
d
Control the cursor in the
menu
e Use to see information on
the current broadcast
f Runs the Anynet view
functions and sets up Anynet+
devices.
g Colour buttons :
Press to add or delete
channels and to store
channels to the favorite
channel list in the “Channel
List” menu.
h Picture-In-Picture On / Off
i Digital subtitle display
j Picture effect selection
k Picture freeze
l
When your remote does not
work, change the batteries
and press the "RESET"
button for 2-3 seconds before
use.
Teletext Functions
6 Exit from the teletext display
0 Teletext index
@
Alternately select Teletext,
Double, or Mix.
$ Teletext size selection
*
Teletext mode selection
(LIST/FLOF)
( Teletext sub page
b P
: Teletext next page
P : Teletext previous page
c Teletext cancel
e Teletext reveal
g Fastext topic selection
h Teletext hold
j Teletext store
The performance of the remote control may be affected by bright light.
This is a special remote control for the visually impaired, and has Braille points on the Power,
Channel, STOP, PLAY/PAUSE and Volume buttons.
English - 7
Page 10
Installing Batteries in the Remote Control
1. Lift the cover at the back of the remote control upward as shown in the
figure.
2. Install two AAA size batteries.
Make sure to match the "+" and "–" ends of the batteries with the
diagram inside the compartment.
3. Replace the cover.
Remove the batteries and store them in a cool, dry place if you won’t be
using the remote control for a long time. The remote control can be used
up to about 23 feet from the TV.
(Assuming typical TV usage, the batteries last for about one year.)
If the remote control doesn’t work, check the following:
1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power outage, or is the power cord unplugged?
5. Is there a special fluorescent light or neon sign nearby?
Switching On and Off
The mains lead is attached to the rear of your set.
1.
Plug the mains lead into an appropriate socket.
The standby indicator lights up on the front of the set.
Press the button on the front of the set.
2.
You also can press the POWER button or the TV/DTV button on the remote control to turn
the TV on.
The programme that you were watching last is reselected automatically.
3. Press the numeric button (0~9) or channel up/down ( / ) button on the remote control or
button on the right side of the set.
When you switch the set on for the very first time, you will be asked to choose language in
which the menus are to be displayed.
4. To switch your set off, press the POWER button again.
Placing Your Television in Standby Mode
Your set can be placed in standby mode in order to reduce the power consumption. The standby
mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).
1.
Press the POWER button on the remote control.
The screen is turned off and a red standby indicator appears on the front of your set.
To switch your set back on, simply press the POWER , numeric buttons (0~9), TV/DTV button or
2.
channel up/down ( / ) button again.
Do not leave your set in standby mode for long periods of time (when you are away on holiday,
for example).
It is best to unplug the set from the mains and aerial.
English - 8
Page 11
Plug & Play
When the TV is initially powered on, several basic settings
proceed automatically and subsequently. The following
settings are available.
Any functions related to Digital TV (DVB) will only work in
countries or areas where DVB-T (MPEG2) digital terrestrial
signals are broadcasted. Please confirm with your local
dealer if you can receive DVB-T signals. Although this TV set
follows the DVB-T specification, maintaining compatibility with
the future coming DVB-T digital terrestrial broadcasts is not
guaranteed. Several functions may not be available in some countries.
1.
Press the POWER button on the remote control.
The message "Start Plug & Play" is displayed with "OK" selected.
2. Select the appropriate language by pressing the ▲ or ▼ button.
Press the ENTER/OK button to confirm your choice.
3. Press the ◄ or ► button to select “Shop” or “Home”, then the ENTER/OK button.
We recommend setting the TV to Home mode for the best picture in your home environment.
Shop mode is only intended for use in retail environments.
If the unit is accidentally set to Shop mode and you want to return to Dynamic (Home) mode, press the Volume button and then hold down the MENU button for five seconds on the side
panel of the TV.
4. The message "Check antenna input." is displayed with "OK" selected.
Press the ENTER/OK button.
Please check that the antenna cable is connected correctly.
5. Select the appropriate country by pressing the ▲ or ▼ button.
Press the ENTER/OK button to confirm your choice.
6. The message “Some DTV functions may not be available. Digital Scan?” is displayed.
Press the ◄ or ► button to select “Yes” or “No”, then press the
ENTER/OK button.
Yes: First an ATV search is performed and then a DTV ch. auto search is performed.
No: Only an ATV search is performed.
This function is supported for all countries except for the following countries: France, Germany,
Italy, Netherlands, Spain, Switzerland, United Kingdom, Austria.
7.
The "Auto Store" menu is displayed with the "Start" selected. Press the
ENTER/OK
The channel search will start and end automatically.
The DTV channel scan menu appears and the DTV channel is automatically updated.
If the DTV channel is updated, the Source in the source list of the Input menu is automatically
changed to DTV.
After all the available channels are stored, the "Clock Set" menu appears.
Press the ENTER/OK button at any time to interrupt the memorization process.
For detailed descriptions about DTV channel update, refer to page 28 of this manual.
After all the available digital channels are stored, the screen to select a time zone is displayed
depending on the country.
8. Press the ENTER/OK button.
Select the "Month", "Day", "Year", "Hour", or "Minute" by pressing the ◄ or ► button.
Set the "Month", "Day", "Year", "Hour", or "Minute" by pressing the ▲ or ▼ button.
You can also set the “Month”, “Day”, “Year”, “Hour” and “Minute” by pressing the number buttons
on the remote control.
9.
Press the ENTER/OK button to confirm your setting. The message “Enjoy your viewing” is
displayed. When you have finished, press the
ENTER/OK button.
Even if the ENTER/OK button is not pressed, the message will automatically disappear after
several seconds.
Language
Country
Auto Store
Clock Set
: Select your language.
: Select your country.
: Automatically scans for and stores channels available in the local area.
: Sets the current time for the TV clock.
English - 9
Plug & Play
Start Plug & Play.
OK
button.
Enter
Page 12
If you want to reset this feature...
Press the MENU button to display the menu.
1.
Press the ▲ or ▼ button to select "Setup", then press the
ENTER/OK button.
Press the ENTER/OK button again, to select "Plug & Play".
2.
3. The message "Start Plug & Play" is displayed.
(Refer to page 9)
TV
Plug & Play
Language : English
Time
Game Mode : Off
Blue Screen : Off
Melody : Off
PC
Home Theatre PC
Light Effect :
More
Move Enter Return
: Off
Plug & Play
Start Plug & Play.
OK
Enter Return
Setup
In Watching TV
TV
- Storing Channels Automatically
- Storing Channels Manually
Analog Channel
Country : Belgium
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA : Off
Move Enter Return
Storing Channels Automatically
You can scan for the frequency ranges available to you (and availability depends on your country).
Automatically allocated programme numbers may not correspond to actual or desired programme
numbers. However, you can sort numbers manually and clear any channels you do not wish to watch.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Analog Channel", then press the ENTER/OK button.
2. Press the ENTER/OK button to select "Country".
3. Select the appropriate country by pressing the ▲ or ▼ button.
Press the ENTER/OK button to confirm your choice.
Even though you have changed the country setting in this menu, the country setting for DTV is not
changed. (Refer to page 28)
4. Press the ▲ or ▼ button to select "Auto Store", then press the ENTER/OK button.
5. Press the ENTER/OK button.
The TV will begin memorizing all of the available channels.
Press the ENTER/OK button at any time to interrupt the memorization process and return to the
"Analog Channel" menu.
6. After all the available channels are stored, the "Sort" menu appears. (refer to page 13)
English - 10
Page 13
Storing Channels Manually
Not available in DTV or external input mode.
TV
You can store television channels, including those received
via cable networks.
When storing channels manually, you can choose:
♦ Whether or not to store each of the channels found.
♦ The programme number of each stored channel which you wish
to identify.
Press the MENU button to display the menu.
1.
Press the ▲ or ▼ button to select "Analog Channel", then
press the ENTER/OK button.
2.
Press the ▲ or ▼ button to select "Manual Store", then press
TV
the ENTER/OK button.
3. Select the required option by pressing the ▲ or ▼ button,
then press the ENTER/OK button.
4. When you are satisfied with your setting, press the
ENTER/OK button.
5.
Press the EXIT button to exit.
♦Programme (Programme number to be assigned to a channel)
− Press the ▲ or ▼ button until you find the correct number.
You can also select the channel number directly by pressing the numeric buttons (0~9).
Colour System: Auto/PAL/SECAM/NTSC4.43
♦
− Press the ▲ or ▼ button to select the required colour standard.
♦ Sound System: BG/DK/I/L
− Press the ▲ or ▼ button to select the required sound standard.
Channel (When you know the number of the channel to be stored)
♦
− Press the ▲ or ▼ button to select C (Air channel) or S (Cable channel).
− Press the ► button, then press the ▲ or ▼ button to select the required number.
You can also select the channel number directly by pressing the numeric buttons (0~9).
If there is abnormal sound or no sound, re-select the sound standard required.
Search (When you do not know the channel numbers)
♦
− Press the ▲ or ▼ button to start the search.
− The tuner scans the frequency range until the first channel or the channel that you selected is
received on the screen.
♦ Store (When you store the channel and associated programme number)
− Set to "OK" by pressing the ENTER/OK button.
Channel mode
− P (Programme mode): When completing tuning, the broadcasting stations in your area have
been assigned to position numbers from P00 to P99. You can select a channel by entering the
position number in this mode.
− C (Air channel mode): You can select a channel by entering the assigned number to each air
broadcasting station in this mode.
− S (Cable channel mode): You can select a channel by entering the assigned number for each
cable channel in this mode.
Analog Channel
Country : Belgium
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA : Off
Move Enter Return
Programme : P 2
Colour System : Auto
Sound System : BG
Channel : C 3
Search : 77 MHz
Store : ?
Manual Store
Move Enter Return
English - 11
Page 14
Adding / Locking Channels
Not available in DTV or external input mode.
➣
Using the Channel Manager, you can conveniently lock or
add channels.
Press the MENU button to display the menu.
1.
Press the ▲ or ▼ button to select "Analog Channel", then
press the ENTER/OK button.
2.
Press the ▲ or ▼ button to select "Channel Manager",
then press the ENTER/OK button.
♦ Adding channels
Using the Channel List, you can add channels.
3. Select Channel List by pressing the ENTER/OK button.
4. Move to the ( ) field by pressing the ▲, ▼, ◄ or ►
button, select a channel to be added, and press the ENTER/
OK button to add the channel.
If you press the
➣
symbol next to the channel disappears and the channel
is not added.
"
" is active when "Child Lock" is selected to "On".
➣
♦ Locking channels
This feature allows you to prevent unauthorized users, such
as children, from watching unsuitable programmes by muting
out video and audio.
5. Press the ▲ or ▼ button to select "Child Lock", then press the ENTER/OK button.
6. Select "On" by pressing the ▲ or ▼ button, then press the
ENTER/OK button.
7. Press the ▲ or ▼ button to select "Channel List",
then press the ENTER/OK button.
8. Move to the ( ) field by pressing the ▲, ▼, ◄ or ► button,
select a channel to be locked, and press the ENTER/OK
button.
If you press the
➣
next to the channel disappears and the channel lock is
canceled.
A blue screen is displayed when Child Lock is activated.
➣
9.
Press the EXIT button to exit.
Select "On" or "Off" in "Child Lock" to easily turn the channels
which selected on " " to be active or inactive.
ENTER/OK button again, the ( )
ENTER/OK button again, the ( ) symbol
TV
TV
P 1 C3
Prog.
0 C--
1 C3
2 BBC 1
3 C74
4 C75
5 C76
6 S3
7 S4
8 S6
9 S7
Add Lock
Move Enter
Page Return
Analog Channel
Country : Belgium
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA : Off
Move Enter Return
Channel Manager
Channel List
Child Lock : Off
Move Enter Return
Channel List
1 / 10
You can select these options by simply pressing the CH LIST
button on the remote control
English - 12
Page 15
Sorting the Stored Channels
This operation allows you to change the programme
numbers of the stored channels.
This operation may be necessary after using the auto store.
Not available in DTV or external input mode.
➣
Press the MENU button to display the menu. Press the ▲ or ▼
1.
button to select "Analog Channel", then press the ENTER/OK button.
TV
Country : Belgium
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA : Off
2. Press the ▲ or ▼ button to select "Sort", then press the
ENTER/OK button.
3. Select the channel number that you wish to change by press
ing the ▲ or ▼ button repeatedly. Press the ENTER/OKbutton.
The selected channel number and name are moved to
right side.
4. Press the ▲ or ▼ button to move to the position in which
you would like to change and then press the ENTER/OK
TV
Prog. Ch. Name
0 C--
1 C23
2 C16
3 C3
4 S1
button.
The selected channel is exchanged with the one
previously stored to the chosen number.
5. Repeat steps 3 to 4 for another channel to be sorted.
6. Press the EXIT button to exit.
Assigning Channels Names
Channel names will be assigned automatically when channel
information is broadcast. These names can be changed,
allowing you to assign new names.
Not available in DTV or external input mode.
➣
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Analog Channel", then
press the ENTER/OK button.
Press the ▲ or ▼ button to select "Name", then press the
2.
ENTER/OK button.
3. If necessary, select the channel to be assigned to a new
name by pressing the ▲ or ▼ button. Press the ENTER/OKbutton.
The selection bar is displayed around the name box.
4.
To...
Select a letter, number or symbol
Move on the next letter
Move back the previous letter
Confirm the name
Then...
Press the ▲ or ▼ button
Press the ► button
Press the ◄ button
ENTER/OK button
Press the
The characters available are : Letters of the alphabet (A~Z) / Numbers (0~9)
Special characters (+, -, *, /, space)
5. Repeat steps 3 to 4 for each channel to be assigned to a new name.
6. Press the EXIT button to exit.
TV
Country : Belgium
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA : Off
TV
Prog. Ch. Name
0 C-- -----
1 C23 -----
2 C16 ----3 C3 ----4 S1 ----
Analog Channel
Move Enter Return
Sort
Move Enter Return
Analog Channel
Move Enter Return
Name
Move Enter Return
English - 13
Page 16
Fine Tuning Channel Reception
Use fine tuning to manually adjust a particular channel for
optimal reception.
Not available in DTV or external input mode.
➣
Use the number buttons to directly select the channel that
1.
you want to fine tune.
2. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Analog Channel", then
press the ENTER/OK button.
3. Press the ▲ or ▼ button to select "Fine Tune", then press
the ENTER/OK button.
4. Press the ◄ or ► button to adjust the fine tuning.
Press the ENTER/OK button.
5. Press the EXIT button to exit.
Fine tuned channels that have been saved are marked with
an asterisk "*" on the right-hand side of the channel number
in the channel banner. And the channel number turns red.
To reset the fine-tuning, select "Reset" by pressing the
▲ or ▼ button and then press the ENTER/OK button.
LNA (Low Noise Amplier)
If the TV is operating in a weak-signal area, the LNA function
can improve the reception (a low-noise preamplifier boosts
the incoming signal).
➣
Not available in DTV or external input mode.
Press the MENU button to display the menu.
1.
Press the ▲ or ▼ button to select "Analog Channel", then
press the ENTER/OK button.
Press the ▲ or ▼ button to select "LNA", then press the
2.
ENTER/OK button.
3. Press the ▲ or ▼ button to select "On" or "Off".
Press the ENTER/OK button.
4. Press the EXIT button to exit.
TV
P 1
Adjust Save Return
TV
TV
Analog Channel
Country : Belgium
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA : Off
Move Enter Return
Fine Tune
Reset
Analog Channel
Country : Belgium
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA : Off
Move Enter Return
Analog Channel
Country : Belgium
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA :
Move Enter Return
Off
On
0
English - 14
Page 17
Changing the Picture Standard
You can select the type of picture which best corresponds to
your viewing requirements.
Press the MENU button to display the menu.
1.
Press the ENTER/OK button, to select "Picture".
2.
Press the ENTER/OK button again, to select "Mode".
3. Press the ▲ or ▼ button to select the desired picture effect.
Press the ENTER/OK button.
4. Press the EXIT button to exit.
♦ Dynamic: Selects the picture for high-definition in a bright
room.
♦ Standard: Selects the picture for optimum display in a
normal environment.
♦ Movie: Selects the picture for comfortable display in a
dark room.
The Picture mode must be adjusted separately for each input
source.
You can also press the P.MODE button on the remote control to
Your set has several settings which allow you to control
picture quality.
To select the desired picture effect, follow the
1.
"Changing the Picture Standard" instructions number 1 to 3.
2. Press the ▲ or ▼ button to select a particular item. Press
the ENTER/OK button.
3. Press the ◄ or ► button to decrease or increase the value
of a particular item. Press the ENTER/OK button.
4. Press the EXIT button to exit.
♦ Contrast: Adjusts the lightness and darkness between objects and the background.
♦ Brightness: Adjusts the brightness of the whole screen.
♦ Sharpness: Adjusts the outline of objects to either sharpen them or make them more dull.
♦ Colour: Adjusts the colours, making them lighter or darker.
♦ Tint:
Adjusts the colour of objects, making them more red or green for a more natural look.
The adjusted values are stored according to the selected Picture mode.
In PC Mode, Only "Contrast" and "Brightness" can be adjusted.
"Tint" is only activated for NTSC broadcasting, DTV broadcasting, " Ext.", "AV", "S-Video",
"Component" and "HDMI" modes.
You can return to the factory defaults picture settings by selecting the "Reset".
(Refer to "Resetting the Picture Settings to the Factory Defaults" on page 19)
Black Adjust : Off
Dynamic Contrast
Gamma : 0
White Balance
My Colour Control
Edge Enhancement
Colour Space
xvYCC
Move Enter Return
Picture
Detailed Settings
: Auto
: Off
: Off
: Off
♦ Black Adjust: Off/Low/Medium/High You can directly select the black level on the screen to adjust
the screen depth.
Dynamic Contrast: Off/Low/Medium/High
♦
You can adjust the screen contrast so that the optimal contrast is provided.
♦ Gamma: -3 ~ +3 You can adjust the Primary Color (Red, Green, Blue) Intensity.
Press the ◄ or ► button until you reach the optimal setting.
♦ White Balance: R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain/Reset
You can adjust the colour temperature for more natural picture colours.
R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain: Changing the adjustment value will refresh the
adjusted screen.
Select the required option by pressing the ▲ or ▼ button, then press the ENTER/OK button. Press the ◄ or ► button until you reach the optimal setting.
Reset: The previously adjusted white balance will be reset to the factory defaults.
♦
My Colour Control: Pink/Green/Blue/White/ResetThis setting can be adjusted to suit your personal preferences.
Pink/Green/Blue/White: Changing the adjustment value will refresh the adjusted screen.
Select the required option by pressing the ▲ or ▼ button, then press the ENTER/OK button. Press the ◄ or ► button until you reach the optimal setting.
Reset: The previously adjusted colours will be reset to the factory defaults.
Edge Enhancement: Off/On
♦
You can emphasize object boundaries.
♦ Colour Space: Auto/Wide
You can set the colour reproduction space for the input signal to Auto or Wide.
♦ XVYCC: Off/OnSetting the xvYCC mode to On increases detail and colour space when watching
movies from an external device (ie. DVD player) connected to the HDMI orComponent IN jacks. You must set the Picture Mode to Movie to enjoy this feature.
Only available in "HDMI" and "Component" on "Movie" mode.
If xvYCC function is active, PIP cannot be selected.
English - 17
Page 20
Changing the Picture Size
You can select the picture size which best corresponds to
your viewing requirements.
1.
Press the MENU button to display the menu.
Press the ENTER/OK button, to select "Picture".
2.
Press the ▲ or ▼ button to select "Size", then press the
ENTER/OK button.
3. Select the required option by pressing the ▲ or ▼ button. Press the ENTER/OK button.
4. Press the EXIT button to exit.
♦
Auto Wide: Automatically adjusts the picture size to the "16:9"
aspect ratio.
♦
16:9: Adjusts the picture size to 16:9 appropriate for DVDs or
wide broadcasting.
♦
Wide Zoom: Magnify the size of the picture more than 4:3.
♦
Zoom: Magnifies the 16:9 wide picture (in the vertical direction)
to fit the screen size.
♦
4:3: This is the default setting for a video movie or normal
broadcasting.
♦
Just Scan: Use the function to see the full image without any
cutoff when HDMI (720p/1080i/1080p) or Component
(720p/1080i/1080p) signals are input.
"Auto Wide" function is available only in "TV", "DTV", "Ext.1",
➣
"Ext.2", "AV", and "S-Video" mode.
In PC Mode, only "16:9" and "4:3" mode can be adjusted.
➣
Depending on the input source, the picture size options may vary.
➣
The items available may differ depending on the selected mode
➣
Zoom : Select by pressing the ◄or ►button.
➣
Use the ▲or ▼button to move the picture up and down.
After selecting
, use the ▲or ▼ button to magnify or
reduce the picture size in the vertical direction.
Wide Zoom : Move the screen up/down using the ▲or ▼ button
➣
after selecting the by pressing the ► or
ENTER/OK button.
TV
More
Size : Auto Wide
Screen Mode : 16 : 9
Digital NR : Auto
Active Colour : On
DNle : On
100Hz Motion Plus
Reset : OK
Move Enter Return
TV
Auto Wide
16 : 9
Wide Zoom
Zoom
4 : 3
Just Scan
Move Enter Return
Picture
: Low
Size
You can select these options
by simply pressing the P.SIZE button on the remote control.
Selecting the Screen Mode
When setting the picture size to Auto Wide in a 16:9 wide TV,
you can determine the picture size you want to see the 4:3
WSS (Wide Screen Service) image or nothing. Each individual
European country requires different picture size so this
function is intended for users to select it.
1.
Press the MENU button to display the menu.
Press the ENTER/OK button, to select “Picture”.
Press the ▲ or ▼ button to select "Screen Mode", then press
2.
the ENTER/OK button.
3. Select the required option by pressing the ▲ or ▼ button.
Press the ENTER/OK button.
♦ 16:9: Sets the picture to 16:9 wide mode.
♦ Wide Zoom: Magnify the size of the picture more than 4:3.
♦ Zoom: Magnify the size of the picture vertically on screen.
♦ 4:3: Sets the picture to 4:3 normal mode.
4. Press the EXIT button to exit.
This function is available in "Auto Wide" mode.
This function is not available in PC, Component or HDMI mode.
English - 18
TV
TV
More
Size : Auto Wide
Screen Mode : 16 : 9
Digital NR : Off
Active Colour : Off
DNle : Off
100Hz Motion Plus
Reset : OK
Move Enter Return
Picture
: Low
16:9
Wide Zoom
Zoom
4:3
Page 21
Digital NR / Active Colour / DNIe / 100Hz Motion Plus
1. Press the MENU button to display the menu. Press the ENTER/OK button, to select “Picture”.
2.
Select the required option by pressing the ▲ or ▼ button,
then press the ENTER/OK button.
Available options: Digital NR, Active Colour, DNIe, 100Hz
Motion Plus.
3. When you are satisfied with your setting, press the
ENTER/OK button.
4. Press the EXIT button to exit.
♦
Digital NR: Off/Low/Medium/High/Auto
If the signal received by the television is weak, you can activate this feature to reduce any static and
ghosting that may appear on the screen.
This function is not available in PC mode.
♦
Active Colour: Off/On
If you turn on this option, the colours of the sky and grass will be stronger and clearer for a more
vivid on-screen picture.
This function is not available in PC mode.
This function is not available in "Movie" and "Standard" mode.
♦
DNIe: Off/On
This TV includes the DNIe function so as to provide a high visual quality. If you set DNIe to on, you
can view the screen with the DNIe feature activated.
DNIeTM (Digital Natural Image engine)
This feature brings you more detailed image with 3D noise reduction, detail enhancement,
contrast enhancement and white enhancement. New image compensation Algorithm gives brighter,
clearer, more detailed image to you. DNIeTM technology will fit every signal into your eyes.
This function is not available in PC mode.
This function is not available in "Movie" mode
♦
100Hz Motion Plus: Off/Low/Medium/High/DemoYou can view more natural skin and clear text even in fast moving scenes.You can view more natural skin and clear text even in fast moving scenes.
This function is not available in PC mode.
TV
More
Size : Auto Wide
Screen Mode : 16 : 9
Digital NR : Auto
Active Colour : On
DNle : On
100Hz Motion Plus
Reset : OK
Move Enter Return
Picture
: Low
Resetting the Picture Settings to the Factory Defaults
You can return to the factory defaults picture settings.
To select the desired picture effect, follow the
1.
"Changing the Picture Standard" instructions number 1 to 3
on page 15.
2. Press the ▲ or ▼ button to select "Reset", then press the ENTER/OK button.
3. Press the ▲ or ▼ button to select "OK" or "Cancel". Press the ENTER/OK button.
4. Press the EXIT button to exit.
The "Reset" will be set for each picture mode.
English - 19
TV
More
Size : Auto Wide
Screen Mode : 16 : 9
Digital NR : Auto
Active Colour : On
DNle : On
100Hz Motion Plus
Reset : OK
Move Enter Return
Picture
: Low
Page 22
Viewing the Picture In Picture (PIP)
You can display a sub picture within the main picture of set
programme or video input. In this way, you can watch the
picture of set programme or video input from any connected
equipment while watching the main picture.
1.
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Setup", then press the
ENTER/OK button.
2.
Press the ▲ or ▼ button to select "PIP", then press the
ENTER/OK button.
3. Select the required option by pressing the ▲ or ▼ button,
then press the ENTER/OK button.
4. When you are satisfied with your setting, press the
ENTER/OK button.
5. Press the EXIT button to exit.
You may notice that the picture in the PIP window becomes
slightly unnatural when you use the main screen to view a
game or karaoke.
♦ PIP: On/Off
You can activate or deactivate the PIP function.
Main pictureSub picture
Component
HDMI 1, 2, 3
PC
Analog TV broadcasts
Ext.1, Ext.2
AV
♦ Source: TV/Ext.1/Ext.2/AV
You can select a source of the sub-picture.
♦ Size: / /
You can select a size of the sub-picture.
If main picture is in "PC" and "Component" mode, "Size" is not available.
➣
♦ Position: / / /
You can select a position of the sub-picture.
♦ Programme
You can select a channel of the sub-picture only when the "Source" is set to "TV".
TV
More
Wall-Mount Adjustment
Energy Saving : Off
HDMI Black Level : Low
PIP
SW Upgrade
Mode : Custom
TV
Equalizer
PIP : On
SRS TS XT : Off
Source : TV
Auto Volume : Off
Size :
Internal Mute : Off
Position : Reset
Programme : P 1
Press the PIP button on the
remote control repeatedly to
activate or deactivate the "PIP".
Setup
Move Enter Return
PIP
Move Enter Return
Move Enter Return
Freezing the Current Picture
Press the STILL button to freeze a moving picture into a
still one. Press again to cancel.
English - 20
Page 23
Sound Features
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Sound", then press the
ENTER/OK button.
2.
Select the required option by pressing the ▲ or ▼ button,
then press the ENTER/OK button.
Available options: Mode, Equalizer, SRS TS XT, Auto
TV
Mode : Custom
Equalizer
SRS TS XT : Off
Auto Volume : Off
Internal Mute : Off
Sound Select : Main
Reset
Sound
Volume, Internal Mute, Sound Select(in
PIP mode), Reset (If Game Mode is On)
3. When you are satisfied with your setting, press the
ENTER/OK button.
4. Press the EXIT button to exit.
Move Enter Return
TV
R
Equalizer
♦ Mode: Standard/Music/Movie/Speech/Custom
You can select the type of special sound effect to be used
when watching a given broadcast.
♦
Equalizer: Balance/100Hz/300Hz/1kHz/3kHz/10kHz
The sound settings can be adjusted to suit your personal
preferences.
If you make any changes to these settings, the sound mode is automatically switched to
➣
L
Balance 100Hz 300Hz 1kHz 3kHz 10kHz
Move Adjust Return
"Custom".
♦ SRS TS XT: Off/On
TruSurround XT is a patented SRS technology that solves the problem of playing 5.1 multichannel
content over two speakers. TruSurround delivers a compelling, virtual surround sound experience
through any two-speaker playback system, including internal television speakers. It is fully
compatible with all multichannel formats.
TruSurround XT, SRS and symbol are trademarks of
SRS Labs, Inc. TruSurround XT technology is incorporated
under license from SRS Labs, Inc.
♦ Auto Volume: Off/On
Each broadcasting station has its own signal conditions, and so it is not easy to adjust the volume
every time the channel is changed. This feature lets you automatically adjust the volume of the
desired channel by lowering the sound output when the modulation signal is high or by raising the
sound output when the modulation signal is low.
♦ Internal Mute: Off/On
If you want to hear the sound through separate speakers, cancel the internal amplifier.
+, - and MUTE buttons do not operate when the "Internal Mute" is set to On.
The
➣
When "Internal Mute" is set to "On", the Sound menus except for "Sound Select" (in PIP
➣
cannot be adjusted.
♦ Sound Select: Main/Sub
When the PIP feature is activated, you can listen to the sound of the sub (PIP) picture.
− Main: Used to listen to the sound of the main picture.
− Sub: Used to listen to the sound of the sub picture.
♦ Reset
If "Game Mode" is On, the Reset Sound function is activated(refer to page 25). Selecting the
Reset function after setting the equalizer resets the equalizer setting to the factory defaults.
mode)
TRADEMARK & LABEL LICENSE NOTICE
Manufactured under license from Dolby Laboratorories.
"Dolby" and the double-D symbol are trademarks of Dolby Laboratories.
English - 21
Page 24
Connecting Headphones
You can connect a set of headphones to your set if you wish to
watch a TV programme without disturbing the other people in the
room.
When you insert the head set jack into the corresponding port, you
➣
can operate only "SRS TS XT", "Auto Volume and "Sound Select"(in
PIP mode) in Sound menu.
Prolonged use of headphones at a high volume may damage your
➣
hearing.
You will not receive sound from the speakers when you connect headphones to the system.
➣
The headphone volume and TV volume are adjusted differently.
➣
Selecting the Sound Mode
You can set the sound mode by pressing the “DUAL” button.
When you press it, the current sound mode is displayed on the
screen.
Audio Type
A2
Stereo
NICAM
Stereo
Mono
Stereo
Dual
Mono
Stereo
Dual
If the stereo signal is weak and an automatic switching occurs, then switch to the Mono.
This function is only activated in stereo sound signal. It is deactivated in mono sound signal.
DUAL 1/2
MONO
STEREO ↔ MONO
DUAL 1 ↔ DUAL 2
MONO
MONO ↔ STEREO
MONO ↔ DUAL 1
DUAL 2
Default
Automatic
change
DUAL 1
Automatic
change
DUAL 1
You can also set these options
simply by pressing the DUALbutton on remote control.
TV Side Panel
Setting and Displaying the Current Time
Mode : Custom
You can set the TV’s clock so that the current time is
displayed when you press the INFO button. You must also
set the time if you wish to use the automatic On/Off timers.
Press the MENU button to display the menu.
1.
Press the ▲ or ▼ button to select "Setup", then press the
ENTER/OK button.
2.
Press the ▲ or ▼ button to select "Time", then press the
ENTER/OK button.
3. Press the ENTER/OK button to select "Clock Set".
4.
To...
Move to Month, Day, Year, Hour or Minute
Set the Month, Day, Year, Hour or Minute
Confirm the setting
Press the...
◄
or ► button.
▲ or ▼ button.
ENTER/OK button.
5. Press the EXIT button to exit.
TV
Equalizer
Plug & Play
SRS TS XT : Off
Language : English
Auto Volume : Off
Time
Internal Mute : Off
Game Mode : Off
Reset
Blue Screen : Off
Melody : Off
PC
Home Theatre PC
Light Effect :
More
Move Enter Return
TV
Move Adjust Return
If you disconnect the power cord, you have to set the clock again
You can also set Year, Month, Day, Hour and Minute by pressing the number buttons on the remote
control.
English - 22
Setup
: Off
p
01
q
00
In Watching TV
Clock Set
Day
01
Move Enter Return
Month
Hour00Minute
Year
2007
Page 25
Setting the Sleep Timer
You can select a time period of between 30 and 180 minutes
after which the television automatically switches to standby
mode.
SRS TS XT : Off
Language : English
Auto Volume : Off
Time
Internal Mute : Off
Game Mode : Off
Reset
Blue Screen : Off
Melody : Off
PC
Home Theatre PC
Light Effect :
More
TV
On Time
Off Time
Repeat
: Off
Move Enter Return
Move Enter Return
Timer 1
5
:
00
00
6
:
0000No
Once
► Move Adjust Return
Setup
In Watching TV
Off
30
60
90
120
150
180
In Watching TV
No
Volume
10
English - 23
Page 26
Choosing Your Language
When you start using your set for the first time, you must
select the language which will be used for displaying menus
and indications.
Press the MENU button to display the on-screen menu.
1.
Press the ▲ or ▼ button to select "Setup", then press the
ENTER/OK button.
2.
Press the ▲ or ▼ button to select "Language", then press
the ENTER/OK button.
3. Select a particular language by pressing the ▲ or ▼ button
repeatedly.
Press the ENTER/OK button.
4. Press the EXIT button to exit.
Upgrading the Software
Samsung may offer upgrades for TV's firmware in the
future. Please contact the Samsung call center to receive
information about downloading upgrades and using a USB
drive. Upgrades will be possible by connecting a USB drive to
the USB port located on located on the side of your TV.
1. Insert a USB drive containing the firmware upgrade into the
WISELINK port on the side of the TV.
Press the MENU button to display the menu.
2.
Press the ▲ or ▼ button to select "Setup", then press the
ENTER/OK button.
3. Press the ▲ or ▼ button to select "SW Upgrade", then press
the ENTER/OK button.
4. Press the ENTER/OK button.
The message "Scanning for USB... It may take up to 30
seconds." is displayed. Please be careful to not disconnect
the power or remove the USB drive while upgrades are being
applied. The TV will shut off and turn on automatically after
completing the firmware upgrade. Please check the firmware
version after the upgrades are complete.
Mode : Custom
TV
Equalizer
Plug & Play
SRS TS XT : Off
Language : English
Auto Volume : Off
Time
Internal Mute : Off
Game Mode : Off
Reset
Blue Screen : Off
Melody : Off
PC
Home Theatre PC
Light Effect :
More
Move Enter Return
Mode : Custom
TV
Equalizer
Plug & Play
SRS TS XT : Off
Language : English
Auto Volume : Off
Time
Internal Mute : Off
Game Mode : Off
Reset
Blue Screen : Off
Melody : Off
PC
Home Theatre PC
Light Effect :
More
Move Enter Return
Setup
: Off
Move Enter Return
Setup
: Off
Move Enter Return
TV Side Panel
TV
More
Wall-Mount Adjustment
Energy Saving : Off
HDMI Black Level
PIP
SW Upgrade
Move Enter Return
TV
USB
Setup
: Low
SW Upgrade
In Watching TV
English
Deutsch
Français
Italiano
Español
Nederlands
q
In Watching TV
USB Drive
English - 24
Enter Return
SW Upgrade
Scanning for USB...
It may take up to 30 seconds.
Page 27
Game Mode/ Blue Screen / Melody / Light Effect / Energy Saving / HDMI Black Level
Mode : Custom
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Setup", then press the
ENTER/OK button.
Select the required option by pressing the ▲ or ▼ button,
2.
then press the ENTER/OK button.
Available options: Game Mode,Blue Screen, Melody, Light
Effect, Energy Saving, HDMI Black Level
3. When you are satisfied with your setting, press the ENTER/
OK button.
4. Press the EXIT button to exit.
♦ Game Mode: Off/On
When connecting to a game console such as PlayStation™
or Xbox™, you can enjoy a more realistic gaming
experience by selecting game menu.
To disconnect the game console and connect another
external device, cancel game mode in the setup menu.
If you display the TV menu in Game mode, the screen
shakes slightly.
"Game Mode" is not available in TV mode.
If Game Mode is On:
• Picture Mode changes to "Standard" and Sound Mode changes to "Custom" automatically.
The user cannot change these to other modes.
• Sound Mode in the Sound menu is deactivated. Adjust the sound using the equalizer.
• The Reset Sound function is activated. Selecting the Reset function after setting the equalizer
resets the equalizer setting to the factory defaults.
♦ Blue Screen: Off/On
If no signal is being received or the signal is very weak, a blue screen automatically replaces the
noisy picture background. If you wish to continue viewing the poor picture, you must set the Blue
Screen to Off.
♦ Melody: Off/Low/Medium/High
The TV power on/off melody sound can be adjusted.
♦ Light Effect: Off/
In Standby
/In Watching TV/Always
You can turn on/off the LED on the front of TV according to the situation. Use it for saving power or
when the LED dazzles your eyes.
− Off: LED will not come on.
− In Standby: Turns the LED on in standby mode.
− In Watching TV: Turns the LED on while watching TV.
− Always: LED will come on after you turn the TV off.
Set the Light Effect to Off to reduce the power consumption.
♦ Energy Saving: Off/Low/Medium/High/Auto
This feature adjusts the screen brightness depending on the surrounding lighting conditions.
− Off: Switches off the Energy Saving mode.
− Low: Operates in standard mode regardless of the surrounding illumination.
− Medium: Enters Medium power saving mode regardless of the surrounding illumination.
− High: Enters maximum power saving mode regardless of the surrounding illumination.
♦ HDMI Black Level: Normal/Low
You can directly select the black level on the screen to adjust the screen depth.
This function is active only when the external input connects to HDMI(RGB signals).
TV
Equalizer
Plug & Play
SRS TS XT : Off
Language :English
Auto Volume : Off
Time
Internal Mute : Off
Game Mode :Off
Reset
Blue Screen :Off
Melody :Off
PC
Home Theatre PC
Light Effect :
More
Move Enter Return
TV
More
Wall-Mount Adjustment
Energy Saving : Off
HDMI Black Level
PIP
SW Upgrade
Move Enter Return
Setup
:Off
Move Enter Return
In Watching TV
Setup
: Low
English - 25
Page 28
Selecting the Source
You can select among external sources connected to your
TV’s input jacks.
Press the MENU button to display the menu.
1.
Press the ▲ or ▼ button to select "Input", then press the
ENTER/OK button.
Press the ENTER/OK button again, to select "Source List".
2.
When no external device is connected to your
set, only "TV", "Ext.1", "Ext.2", "DTV" are activated in the
"Source List". "AV", "S-Video", "Component", "PC",
"HDMI1", "HDMI2","HDMI3" are activated only
when they are connected to your set.
3. Select the required device by pressing the ▲ or ▼ button. Press the ENTER/OK button.
Press the SOURCE button on the remote control to toggle
between all the available source.
TV mode can be selected by pressing the TV/DTV button,
number buttons(0~9), and the P / button on the remote
control. But it cannot be selected using the SOURCE button.
Mode : Custom
TV
Equalizer
Source List : TV
SRS TS XT : Off
Edit Name
Auto Volume : Off
Anynet+(HDMI-CEC)
Name the device connected to the input jacks to make your
input source selection easier.
Press the MENU button to display the menu.
1.
Press the ▲ or ▼ button to select "Input", then press the
ENTER/OK button.
2.
Press the ▲ or ▼ button to select "Edit Name", then press
the ENTER/OK button.
3. Press the ▲ or ▼ button to select the device that you wish to edit.
Press the ENTER/OK button.
4. Press the ▲ or ▼ button to select the required device. Press the ENTER/OK button.
5. Press the EXIT button to exit.
When a PC with a resolution of 1920 x 1080@60Hz is
connected to the HDMI IN 2 port, you should set the"
HDMI2" mode to "PC" in the "Edit Name" of the "Input"
mode.
English - 26
Mode : Custom
TV
Equalizer
Source List : TV
SRS TS XT : Off
Edit Name
Auto Volume : Off
Anynet+(HDMI-CEC)
Internal Mute : Off
WISELINK Reset
Move Enter Return
Move Enter Return
Mode : Custom
TV
Equalizer
Ext.1 : ----
SRS TS XT : Off
Ext.2 : ----
Auto Volume : Off
AV : ----Internal Mute : Off
S-Video : ----
Component : ----
Reset
PC : ----
HDMI1 : ----
HDMI2 : ----
HDMI3 : ----
Edit Name
Move Enter Return
Move Enter Return
Input
----
VCR
DVD
D-VHS
Cable STB
HD STB
Satellite STB
q
Page 29
Previewing the DTV Menu System
♦ The company does not guarantee the normal operation of the
DTV menu for countries other than the supported countries
(France, Germany, Italy, Netherlands, Spain, Switzerland,
United Kingdom, Austria) because only these country standards
are supported.
In addition, when the country of the broadcast stream differs
from the country selected by the current user, the string
appearing in the channel banner, Info, Guide, Channel
Manager, etc. may not be displayed properly.
♦ Available in DTV mode. Preset to the DTV mode by using the
TV/DTV button on your remote control. To help you navigate
around the on-screen menu system and adjust the various
settings available, refer to the following illustration.
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press the
ENTER/OK button.
Guide
Now & Next Guide
Full Guide
Scheduled List
Default Guide
Channel
Country
Auto Store
Manual Store
Edit Favourite Channels
Channel List
Setup
Menu Transparency
Change PIN
Parental Lock
Subtitle
Subtitle Mode
Audio Format
Digital Text
Time Zone
System
Language
Audio Language
Subtitle Language
Teletext Language
Preference
Now/Next, Full Guide
All, Favourites, Default
High, Medium, Low, Opaque
Off, On
Normal, Hard of hearing
PCM, Dolby Digital
Disable, Enable
Product Information
Signal Information
Software Upgrade
Common Interface
Reset
Primary Audio Language
Secondary Audio Language
Primary Subtitle Language
Secondary Subtitle Language
Primary Teletext Language
Secondary Teletext Language
Mode : Custom
TV
Equalizer
Guide
SRS TS XT : Off
Channel
Auto Volume : Off Internal Mute : Off
Setup
Reset
Language
Mode : Custom Equalizer
Now & Next Guide SRS TS XT : Off
Full Guide
Auto Volume : Off
Scheduled List
Internal Mute : Off
Default Guide : Full Guide
Reset
Country :
Auto Store
Manual Store
Edit Favourite Channels
Channel List
Menu Transparency
Change PIN
Parental Lock
Subtitle : On
Subtitle Mode : Normal
Audio Language
Subtitle Language
Teletext Language
Preference
Digital Menu
Move Enter Return
Move Enter Exit
Guide
Move Enter Return
Move Enter Exit
Channel
Move Enter Return
Move Enter Exit
Setup
: Medium
Move Enter Return
Move Enter Exit
Language
Move Enter Return
Move Enter Exit
United Kingdom
The sub-items of the CI Menu may vary depending on the CAM model.
English - 27
Page 30
Updating the Channel List Automatically
You can update the channel list when the broadcaster
adds new Services or if you move the TV to a new
location.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then
press the ENTER/OK button.
2.
Press the
the ENTER/OK button.
3. Press the ENTER/OK button again, to select "Country".
4. Select the appropriate country by pressing the ▲ or ▼
button. Press the ENTER/OK button to confirm your choice.
5. Press the Press the ENTER/OK button.
6. Press the EXIT button to exit.
▲ or ▼
button to select "Channel", then press
Even though you have changed the country setting
in this menu, the country setting for Analog TV is not
changed.(Refer to page 10)
▲ or ▼
button again, to select "Auto Store".
When it has finished, the number of scanned services
will be displayed.
The existing favourite channel list will not be deleted
when the channel list is updated.
To stop the scan before it has finished, press the ENTER/OK button with "STOP"
selected.
If the signal status is poor, the "No Service found! Check the aerial connection" message
is displayed.
Country :
Auto Store
Manual Store
Edit Favourite Channels
Channel List
Move Enter Return
Mode : Custom
Equalizer SRS TS XT : Off Auto Volume : Off
Scanning for digital services...
Internal Mute : Off
Reset
Services found: 24 Channel: 38
Channel
United Kingdom
Auto Store
35%
Stop
Move Enter Return
Return
Updating the Channel List Manually
You can specify the channel for a fast channel search.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then
Channel
press the ENTER/OK button.
2.
Press the
▲ or ▼
button to select "Channel", then press
the ENTER/OK button.
3. Press the
▲ or ▼
button to select "Manual Store", then
press the ENTER/OK button.
4. Press the
▲ or ▼
button to select the required option,
then press the ENTER/OK button.
− Channel : Channel "5" to "69" in sequence are displayed (depending on the country)
− Frequency : The frequency available in the Channel group is displayed.
− Bandwidth : The available bandwidths are 7 and 8 MHz.
Press the red button to start the scan for digital services.
When it has finished, channels are updated in the channel list.
5. When it has finished, the number of scanned services will be displayed.
6. Press the EXIT button to exit.
English - 28
Manual Store
FrequencyBandwidth
▲
5
177500
▼
Search
Adjust Return
KHzMHz
7
Page 31
Editing Your Favourite Channels
You can edit your favourite channels using the four colour
buttons.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press
the ENTER/OK button.
2. Press the ▲ or ▼ button to select "Channel", then press the
ENTER/OK button.
3. Press the ▲ or ▼ button to select "Edit Favourite Channels",
then press the ENTER/OK button.
4. Press the red button to display all currently stored channels.
5. Press the ▲ or ▼ button to select a channel you want.
Press the ENTER/OK button.
A "" icon is shown next to the selected channel and the
channel will be added to the favourite channel list.
•
6. Press the EXIT button to exit.
To undo, press the
•
Select All: Select all channels currently displayed.
•
Select None: Deselect all selected channels.
•
Preview: Displays (a) currently selected channel(s).
The Favorite Channels settings have been completed.
ENTER/OK button again.
Edit Favourite Channels
(no Channels)
Move Enter Return
Add Channels
Return
Edit Favourite Channels
2 BBC TWO
5 Five
7 BBC THREE
15 abc1
16 QVC
Move Enter Return
Select All Select None Preview
Move Select Return
♦ Add
You can use this function when one or more favourite
channels have been selected.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press
the ENTER/OK button.
2. Press the ▲ or ▼ button to select "Channel", then press the
ENTER/OK button.
3. Press the ▲ or ▼ button to select "Edit Favourite Channels",
then press the ENTER/OK button.
4. Press the red button in the "Edit Favourite Channels" menu.
To add more channels, refer to the step 5 on the previous
description.
5.
If you want to check the channel to be stored, press
RETURN button.
Press the
EXIT button to exit.
• To add all channels to the favourite channel list, press theTo add all channels to the favourite channel list, press the
red button.
• To remove all channels, press the green button.• To remove all channels, press the green button.To remove all channels, press the green button.
•• Preview : Displays (a) currently selected channel(s).
• Press the• Press thePress the CH LIST button to display the favourite channel
manager.
Edit Favourite Channels
2 BBC TWO ★
7 BBC THREE ★
15 abc1 ★
Move Enter Return
Add
Renumber
Preview Delete
Move Return
Edit Favourite Channels
2 BBC TWO ★
5 Five
7 BBC THREE ★
15 abc1 ★
16 QVC
Move Enter Return
Select All Select None Preview
Move Select Return
English - 29
Page 32
♦ Renumber (depending on the country)
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press
the ENTER/OK button.
2. Press the ▲ or ▼ button to select "Channel", then press the ENTER/OK button.
3. Press the ▲ or ▼ button to select "Edit Favourite Channels", then press the ENTER/OK button.
4. Select the required channel using the ▲ or ▼ button.
5. Press the green button.
The space for entering the number is a blank.
6. Enter the new channel number. Press ENTER/OK button to
store or RETURN button to cancel.
Press the ◄ button to delete an entered digit.
If you enter a number already assigned to another channel,
the number is assigned to the selected channel and the
previous number assigned to the selected channel is
assigned to the other channel.
That is, the two numbers are exchanged.
The favorite channels are automatically sorted in
ascending order of channel numbers.
7. Press the EXIT button to exit.
Edit Favourite Channels
2 BBC TWO ★
BBC THREE ★
-- 15 abc1 ★
Move Enter Return
Edit Return Conrm
♦ Preview
1. In the "Edit Favourite Channels" menu,
select the channel to be previewed by pressing the ▲ or ▼
button.
2. Press the yellow button.
The selected channel is displayed on the screen.
♦ Delete
1. In the "Edit Favourite Channels" menu, select the channel to
be deleted from the favourite channels list by pressing the
▲ or ▼ button.
2. Press the blue button.
The selected channel and number will be deleted.
To add a deleted channel back in to the favourite channel
list, see "Add" on page 29.
English - 30
Edit Favourite Channels
2 BBC TWO ★
7 BBC THREE ★
15 abc1 ★
Add
Renumber
Preview Delete
Move Return
Edit Favourite Channels
2 BBC TWO ★
7 BBC THREE ★
Add
Renumber
Move Return
Preview Delete
Page 33
Selecting Channel List
You can exclude the channels you have chosen from the
channels you have scanned.When you scan through the
stored channels, those you have chosen to skip are not
displayed. All channels that you do not specifically choose
to skip are displayed during scanning.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press
2. Press the ▲ or ▼ button to select "Channel", then press the ENTER/OK button.
3. Press the ▲ or ▼ button to select "Channel List". Press the ENTER/OK button.
4.
Press the ▲ or ▼ button to select "All", "Favourites" or
"Default".
It can be displayed simply by
pressing the CH LIST button.
Press the ENTER/OK button.
5. Press the yellow button to toggle between your favourite
channels and all channels.
Your favourite channels are only displayed if they were previously set in the "Editing Your
Favourite Channels" menu (refer to page 29).
6. Press the red or green button to display the previous or next channel List page.
7. Press the ▲ or ▼ button to select a channel to be tuned.
Press the ENTER/OK button.
The channel number, name and an icon are displayed in the top left corner while changing the
channel. The channel number and name are displayed if the channel is one of the all channels,
and a icon if the channel is one of the favourite channels.
8. Press the blue button to toggle between your TV, Radio, Data/Other and All.
9. Press the CH LIST button to exit from the channel List.
60 Television X
70 BBC Radio 1
72 BBC Radio 2
73 BBC Radio 3
74 BBC Radio 4
84 heat
91 MOJO
800 ARD-MHP-Data
More
1/2
Displaying Programme Information
While viewing a channel, additional information about the
current programme may be displayed.
1. While viewing a programme, press the INFO button.
The programme information is displayed.
➣
2. To exit from banner information, press the INFO button.
➣
The information is displayed:
− Parental Rating
− Video Type: SD, HD, Radio
− Audio Type: Mono, Stereo, Dual, Dolby Digital
− Existence of Teletext or DVB Subtitle
− Audio Language
English - 31
1 AFDO,16:9
AFDO 16:9
No Block
SD
Stereo
Subtitle
English
Exit
14:30 Sat 1 Sep
AII Channels
A
14:30~14:33
Contains video with AFD O; coded frame
is 16:9
Move Enter Return
Page 34
Viewing the EPG (Electronic Programme Guide) Information
The EPG (Electronic Programme Guide) information is
provided by the broadcasters. Programme entries may
appear blank or out of date as a result of the information
broadcast on a given channel. The display will dynamically
update as soon as new information becomes available.
♦ Now & Next Guide
For the six channels indicated in the left-hand column,
displays the Current programme and the Next programme
information.
♦ Full Guide
Displays the programme information as time ordered One
hour segments. Two hours of programme information is
displayed which may be scrolled forwards or backwards in
time.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press
the ENTER/OK button.
2. Press the ENTER/OK button, to select "Guide".
3. Press the ▲ or ▼ button to select "Now & Next Guide" or
"Full Guide".
Press the ENTER/OK button.
You can also display the guide menu simply by pressing
the GUIDE button.
4.
To...Then...
Watch a programme in the EPG list
If the next programme is selected, it is scheduled with the clock icon
displayed. If the
canceled with the clock icon gone. For details about scheduling
programmes, refer to the next page.
View programme information
Toggle between the "Now & Next
Guide" or "Full Guide"
Display the "Favourites" and the "All
Channels" list
Scrolls backwards quickly (24 hours).• Press the yellow button repeatedly.
Scrolls forward quickly (24 hours).• Press the blue button repeatedly.
Exit the guide• Press the
ENTER/OK button is pressed again, the scheduling is
• Select a programme by pressing
the ▲, ▼, ◄, ► button.
• Press the
ENTER/OK button.
• Select a programme of your choice by
pressing the ▲, ▼, ◄, ► button.
• Press the INFO button when the
programme of your choice is
highlighted.
• Press the red button repeatedly.
• Press the green button repeatedly.
EXIT button.
AllChannels
Watch
Watch
Now/Next Favourites -24Hours +24Hours Exit
Now & Next Guide
Full Guide
13:28 Wed 16 Feb
INFO
13:28 Wed 16 Feb
INFO
27 Discovery
Extreme Machines: Armoured Cars
NowNext
Full Guide Favourites Exit
27 Discovery
Extreme Machines: Armoured Cars
13:0014:00Today
The programme title is on the upper part of the screen center. Please click on INFO button for
the detailed information. Channel Number, Running Time, Status Bar, Parental Level, Video Quality
Information(HD/SD), Sound Modes, Subtitle or Teletext, Languages of Subtitle or Teletext, and
brief summary of the highlighted programme are included on the detailed information. "..." will be
appeared if the summary is long.
Six channels are displayed. To scroll between channels, move to a channel using the ▲ or ▼
button. To display page by page, use the P or button.
English - 32
Page 35
Using the Scheduled List
If you make a scheduled viewing list of programs you may
like to see, the channel will be automatically switched to the
scheduled programme at the scheduled time even if you are
watching another programme.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press
the ENTER/OK button.
2. Press the ENTER/OK button, to select "Guide".
3. Press the ▲ or ▼ button to select "Scheduled List", then press the ENTER/OK button.
4. Press the red button.
The channel will be switched to the scheduled programme.
5. Press the ENTER/OK button to select an item and adjust with
the ▲ or ▼ button .
You can also set hour and minute by pressing the number
buttons on the remote control.
•
Channel: Set the channel.
•
Time: Set the time.
•
Date: Set Year, Month and Day.
•
Frequency: Set the frequency.
("Once", "Daily", or "Weekly")
6. After setting the schedule, Press the red button.
7. Press the EXIT button to exit.
•
Save: Save the adjusted schedule.
•
Cancel: Cancel the adjusted schedule.
•
Add Programme: Add a new schedule.
• Edit: Re-adjust the selected schedule.
•
Delete: Delete the selected schedule.
Scheduled List
(No programmes)
Add Programme
Return
Scheduled List
Tuesday 22 Apr 15:30 ~ 16:00 Once
801 RaiTre
Add Programme
Move Return
SaveCancel
Adjust Move Return
Channel
Time
Date
Frequency
EditDelete
Scheduled List
802 RaiUno
15 : 20 to -- : --
Tue 22 Apr 2007
Once
Setting the Default Guide
You can preset the default guide style.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press
the ENTER/OK button.
2. Press the ENTER/OK button, to select "Guide".
3. Press the ▲ or ▼ button to select "Default Guide", then
press the ENTER/OK button.
4. Select "Now/Next" or "Full Guide" using the ▲ or ▼ button, and press the ENTER/OK button.
5. Press the EXIT button to exit.
English - 33
Now & Next Guide
Full Guide
Scheduled List
Default Guide : Full Guide
Guide
Now/Next
Full Guide
Move Enter Return
Move Enter Return
You can select these options
by simply pressing the GUIDE
button on the remote control.
Page 36
Viewing All Channels and Favourite Channels
In the EPG menu, you can display all channels or favourite
channels.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press
the ENTER/OK button.
2. Press the ENTER/OK button again, to select "Guide".
3. Select the your required guide ("Now & Next Guide" or "Full
Guide") by pressing the ▲ or ▼ button.
4. Press the ENTER/OK button.
5. Press the green button.
All the channel lists and the favorite channel lists will be
toggled.
6. Select a programme of your choice by pressing the ▲, ▼, ◄,
or ► button.
7. Press the INFO button to display information about the
highlighted programme.
8. When the Edit Favourite Channels list has not been set up:
••
"The favourites list is empty.
Would you like to choose your favourites now?" message is
displayed.
•
Select "Yes".
The "Edit Favourite Channels" menu is displayed.
If you select "No", all channels will remain unchanged.
• To edit the favourite channels, refer to pageTo edit the favourite channels, refer to page 29 for more
details.
9 . Press the EXIT button to exit.
All Channels" is the list of channels that have been scanned by
"
the channel list update.
All channels are displayed in the all channel mode.
Favourites" (favourite channels) is the list of channels that has
"
been set in the "Edit Favourite Channels" menu (refer to page 29).
AllChannels
Watch
27 Discovery
Extreme Machines: Armoured Cars
Watch
Full Guide Favourites Exit
27 Discovery
Extreme Machines: Armoured Cars
The favourites list is empty.
Would you like to choose your
favourites now?
Now/Next Favourites -24Hours +24Hours Exit
Now & Next Guide
NowNext
Full Guide
13:0014:00Today
YesNo
13:28 Wed 16 Feb
INFO
13:28 Wed 16 Feb
INFO
Adjusting the Menu Transparency
You can set the Transparency of the menu.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press
the ENTER/OK button.
2. Press the ▲ or ▼ button to select "Setup", then press
the ENTER/OK button.
3. Press the ▲ or ▼ button to select "Menu Transparency" then press the ENTER/OK button.
4. Select the required option ("High", "Medium", "Low", or
"Opaque") by pressing the ▲ or ▼ button, and press the
ENTER/OK button to change the setting.
5. Press the EXIT button to exit.
English - 34
Menu Transparency
Change PIN
Parental Lock
Subtitle :On
Subtitle Mode : Normal
Setup
: Medium
High
Medium
Low
Opaque
Move Enter Return
Page 37
Setting up the Parental Lock
This feature allows you to prevent unauthorized users, such
as children, from watching unsuitable programmes by a
4-digit PIN (Personal Identification Number) code that is
defined by the user. The on-screen menu will instruct you to
assign a PIN code (you can change it later, if necessary).
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press
the ENTER/OK button.
2. Press the ▲ or ▼ button to select "Setup", then press the ENTER/OK button.
3. Press the ▲ or ▼ button to select "Parental Lock.", then press the ENTER/OK button.
4.
The "Enter PIN" is displayed.
5. Enter your current 4-digit PIN code by using the numeric
buttons (0~9). The default PIN code for a new TV set is 0000.
If you enter an invalid PIN code,the "Invalid PIN code.
Please try again." message is displayed.
6. Press the ENTER/OK button.
7. Press the ▲ or ▼ button to select the age rating you want to
lock out.
Press the ENTER/OK button.
Change PIN
♦
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press
the ENTER/OK button.
2. Press the ▲ or ▼ button to select "Setup", then press the ENTER/OK button.
3. Press the ▲ or ▼ button to select "Change PIN", then press the ENTER/OK button.
➣
The "Enter PIN" is displayed.
4. Enter your current 4-digit PIN code by using the numeric
buttons (0~9).
The “Enter New PIN” is displayed.
➣
5. Enter your new PIN code by using the numeric buttons (0~9)
The "Conrm New PIN" is displayed.
➣
6. Re-enter your new PIN code to confirm by using the numeric
buttons (0~9).
The Your PIN code has been changed successfully
➣
message is displayed.
7. Press the ENTER/OK button.
8. Press the EXIT button to exit.
If you forget the PIN code, press the remote control buttons
➣
in the following sequence, which resets the PIN to 0-0-0-0:
POWER (Off), MUTE, 8, 2, 4, POWER (On).
Menu Transparency
Change PIN
Parental Lock
Subtitle : On
Subtitle Mode : Normal
Enter PIN
Parental Rating: No Block
Menu Transparency
Change PIN
Parental Lock
Subtitle : On
Subtitle Mode : Normal
Confirm New PIN
Your PIN code has been changed
successfully.
Setup
: Medium
Move Enter Return
Move Enter Return
Parental Lock
Enter PIN Return
Parental Lock
▲
No Block
No Block
3
4
5
6
Setup
: Medium
Change PIN
OK
▼
Move Enter Return
Move Enter Return
Move Enter Return
Move Enter Return
Enter PIN Return
English - 35
Page 38
Setting the Subtitle
You can activate and deactivate the subtitles.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press
the ENTER/OK button.
2. Press the ▲ or ▼ button to select "Setup", then press the ENTER/OK button.
3. Press the ▲ or ▼ button to select "Subtitle ", then press the ENTER/OK button.
4. Select "On" by pressing the ▲ or ▼ button. Press the ENTER/OK button.
5. Press the EXIT button to exit.
Setting the Subtitle Mode
Use this menu to set the Subtitle Mode. "Normal" under
the menu is the basic subtitle and "Hard of hearing" is the
subtitle for a hearing-impaired person.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press
the ENTER/OK button.
2. Press the ▲ or ▼ button to select "Setup", then press the
ENTER/OK button.
3. Press the ▲ or ▼ button to select "Subtitle Mode", then
press the ENTER/OK button.
4. Press the ▲ or ▼ button to select "Normal" or "Hard of hearing". Press the ENTER/OK button.
5. Press the EXIT button to exit.
If the programme you are watching does not support the
"Hard of hearing" function, "Normal" automatically activates
even though "Hard of hearing" mode is selected.
Menu Transparency
Change PIN
Parental Lock
Subtitle: On
Subtitle Mode : Normal
Menu Transparency
Change PIN
Parental Lock
Subtitle : On
Subtitle Mode : Normal
Setup
: Medium
Off
On
Move Enter Return
Move Enter Return
Setup
: Medium
Normal
Hard of hearing
Move Enter Return
Move Enter Return
Selecting the Audio Format
You can only hear Dolby Digital sound through the audio
receiver connected through an optical cable. You can only
hear PCM sound through the main speaker.
When sound is emitted from both the main speaker and the
audio receiver, a sound echo may occur due to the decoding
speed difference between the main speaker and the audio
Audio Format : PCM
Digital Text : Enable
Time Zone
System
receiver. In this case, use the internal mute function.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press
the ENTER/OK button.
2. Press the ▲ or ▼ button to select "Setup", then press the ENTER/OK button.
3. Press the ▲ or ▼ button to select "Audio Format", then press the ENTER/OK button.
4. Press the ▲ or ▼ button to select "PCM" or "Dolby Digital". Press the ENTER/OK button.
5. Press the EXIT button to exit.
The Audio Format appears according to the broadcasting signal.
Dolby digital sound is only available when the TV is connected with an external speaker using an
optical cable.
English - 36
Setup
Move Enter Return
Page 39
Selecting the Digital Text
If the programme is broadcast with digital text, this feature
is enabled.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press
the ENTER/OK button.
Audio Format : PCM
Digital Text : Enable
Time Zone
System
2. Press the ▲ or ▼ button to select "Setup", then press the ENTER/OK button.
3. Press the ▲ or ▼ button to select "Digital Text", then press the ENTER/OK button.
4. Press the ▲ or ▼ button to select "Disable" or "Enable". Press the ENTER/OK button.
5. Press the EXIT button to exit.
MHEG(Multimedia and Hypermedia Information Coding Experts Group) An International standard for data
encoding systems used in multimedia and hypermedia. This is at a higher level than the MPEG system
which includes data-linking hypermedia such as still images, character service, animation, graphic and
video files as well as multimedia data. MHEG is user runtime interaction technology and is being applied
to various fields including VOD (Video-On-Demand), ITV (Interactive TV), EC (Electronic Commerce),
tele-education, tele-conferencing, digital libraries and network games.
Setup
Move Enter Return
Selecting the Time Zone (Spain only)
Select the time zone where locate
1.
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press
the ENTER/OK button.
2. Press the ▲ or ▼ button to select "Setup", then press the ENTER/OK button.
3. Press the ▲ or ▼ button to select "Time Zone", then press the ENTER/OK button.
4. Select the time zone where you locate by pressing the
▲ or ▼
button.
Press the ENTER/OK button.
The following options are available
The Iberian Peninsula and Balearic Islands -
Canary Islands
5. Press the EXIT button to exit.
Audio Format : PCM
Digital Text : Enable
Time Zone
System
The Iberian Peninsula and Balearic Islands
Canary Islands
Setup
Move Enter Return
Time Zone
Disable
Enable
Viewing Product Information
You can view your product information. For service or
repair, please contact a Samsung approved dealer.
1.
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press
the ENTER/OK button.
2.
Press the ▲ or ▼ button to select "Setup", then press the
ENTER/OK button.
3. Press the
the ENTER/OK button.
4. Press the ENTER/OK button again, to select "Product
Information".
- Software Version, Firmware Version
5. Press the EXIT button to exit.
▲ or ▼
button to select "System", then press
The Product Information menu is selected.
English - 37
Adjust Enter Return
Product Information
Software Version: T-PNRDEUCW-0808
Firmware Version: T-MOJODEUB-101k
Return
Page 40
Checking the Signal Information
You can get information about the signal status.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press
the ENTER/OK button.
2.
Press the ▲ or ▼ button to select "Setup", then press the
ENTER/OK button.
3. Press the ▲ or ▼ button to select "System", then press the ENTER/OK button.
4. Press the ▲ or ▼ button to select "Signal Information",
Signal Information
Service: ?
Service ID:0000
Multiplex: ? (TSID 0000, ONID 0000)
Network: ? (ID 0000)
Bit error level: 10
Signal Strength: 0
Move Enter Return
Return
then press the ENTER/OK button.
5. Press the EXIT button to exit.
If the signal status is poor, the "No signal." message is
displayed.
Upgrading the Software
To keep your product up-to-date with new Digital Television
features then software upgrades are periodically broadcast
as part of the normal Television signal.
It will automatically detect these signals and display the
software upgrade banner. You are given the option to install
the upgrade.
Product Information
Signal Information
Software Upgrade
Common Interface
Reset
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press
the ENTER/OK button.
2. Press the ▲ or ▼ button to select "Setup", then press the
ENTER/OK button.
3. Press the ▲ or ▼ button to select "System", then press the
ENTER/OK button.
Software Information
Manual Upgrade
Standby Mode upgrade : On
4. Press the ▲ or ▼ button to select "Software Upgrade", then press the ENTER/OK button.
5.
Press the
▲ or ▼
button to select “Software Infomation”,
“Manual Upgrade” or “Satandby Mode upgrade”.
Press the ENTER/OK button.
♦ Software Inforamtion
Press the ENTER/OK button, then the current software version is shown. To display the software
version information, press the ENTER/OK button again.
To switch to an alternative version, press the red button.
Press the blue button to reset, activate the upgrade and restart.
♦
Manual Upgrade
Press the ENTER/OK button to search for new software from the currently broadcasting channels.
♦
Standby Mode Upgrade : On / Off
Press the ENTER/OK button. To continue software upgrade with master power on, Select On
by pressing the ▲ or ▼ button. 45 minutes after entering standby mode, a manual upgrade is
automatically conducted. Since the power of the unit is turned on internally, the screen may be on
slightly for the LCD product. This phenomenon may continue for more than 1 hour until the software
upgrade is completed.
6. Press the EXIT button to exit.
System
Move Enter Return
Software Upgrade
Move Enter Return
English - 38
Page 41
Viewing Common Interface
This contains information on CAM inserted in the CI slot and
displays it.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press
Type : CA
Manufacturer : Channel Plus
Info : Top Up TV
the ENTER/OK button.
2. Press the ▲ or ▼ button to select "Setup", then press the ENTER/OK button.
3. Press the ▲ or ▼ button to select "System", then press the ENTER/OK button.
4. Press the ▲ or ▼ button to select "Common Interface", then press the ENTER/OK button.
5. Press the ENTER/OK button to display the information for
your application.
6. Press the EXIT button to exit.
The Application Info inserting is about the CI CARD.
You can install the CAM anytime whether the TV is ON or
OFF.
1. Purchase the CI CAM module by visiting your nearest dealer
or by phone.
2. Insert the CI CARD into the CAM in the direction of the
arrow until it fits.
3. Insert the CAM with the CI CARD installed into the common
interface slot.
(Insert the CAM in the direction of the arrow, right up to the end
so that it is parallel with the slot.)
4. Check if you can see a picture on a scrambled signal
channel.
Selecting the CI (Common Interface) Menu
Application Info
Return
This enables the user to select from the CAM-provided menu.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press
the ENTER/OK button.
2. Press the ▲ or ▼ button to select "Setup", then press the ENTER/OK button.
3. Press the ▲ or ▼ button to select "System", then press the ENTER/OK button.
4. Press the ▲ or ▼ button to select "Common Interface", then press the ENTER/OK button.
5. Select to "CI Menu" by pressing the ▲ or ▼ button, and press the ENTER/OK button.
6. Select the required option by pressing the ▲ or ▼ button, and press the ENTER/OK button.
7. Press the EXIT button to exit.
Select the CI Menu based on the menu PC Card.
English - 39
Main menu
Module informa tion
Smart card inf ormation
Language
Software Downl oad
Press OK to select, or Exit to quit
Move Enter Exit
CI Menu
Page 42
Resetting
You can reset the values stored to the factory default
values.
The Reset operation deletes all channel information and
Enter PIN
Reset
user preferences returningall values to their default factory
state.
1.
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press
the ENTER/OK button.
2. Press the ▲ or ▼ button to select "Setup", then press the ENTER/OK button.
3. Press the
▲ or ▼
button to select "System", then press
the ENTER/OK button.
4. Press the
▲ or ▼
button to select "Reset", then press the
Enter PIN Return
WARNING: All channel settings and user
preferences will be lost and returned to the factory
defaults. It is recommended that a reset is performed
only when serious problems are experienced.
Reset
ENTER/OK button.
5. The "Enter PIN" screen will appear.
6. Enter your current 4-digit PIN code by using the numeric
buttons (0~9).
The warning message is displayed.All values will be
Return
reset by pressing the coloured buttons (red, green,
yellow, and blue)in turn.
7. Press the EXIT button to exit.
Selecting the Preferred Language (Subtitle , Audio or Teletext)
You can change the default value for subtitle, audio teletext
languages.
Displays the language information for the incoming stream.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Digital Menu", then press
the ENTER/OK button.
2. Press the ▲ or ▼ button to select "Language", then press the ENTER/OK button.
3.
Press the
▲ or ▼
button to select "Audio Language",
"Subtitle Language" or "Teletext Language".
Press the ENTER/OK button.
4. Select a particular language by pressing the ▲ or ▼ button repeatedly.
Press the ENTER/OK button.
English is the default in cases where the selected
language is unavailable in the broadcast.
5. Press the EXIT button to exit.
While viewing a programme, the subtitle can be selected
While viewing a programme, audio languages can be
selected.
Audio Language
Subtitle Language
Teletext Language
Preference
Audio Language
Subtitle Language
Teletext Language
Preference
Audio Language
Subtitle Language
Teletext Language
Preference
Language
Move Enter Return
Language
Move Enter Return
Language
English - 40
Move Enter Return
Page 43
Preference
This menu consists of 6 sub-menus:
Primary Audio Language, Secondary Audio Language,
Primary Subtitle Language, Secondary Subtitle Language,
Primary Teletext Language, Secondary Teletext Language.
Using this feature, users can select one of the languages
(English, German, Italian, Swedish, French, Welsh, Gaelic, Irish,
Danish, Finnish, Spanish, Dutch). The language selected here is
the default when the user selects
a channel.
Audio Language
Subtitle Language
Teletext Language
Preference
Language
Move Enter Return
Move Enter Return
♦ Press the ▲ or ▼ button to select required menu (Primary Audio Language, Secondary Audio
Language, Primary Subtitle Language, Secondary Subtitle Language, Primary Teletext Language,
Secondary Teletext Language), then press the ENTER/OK button. The options of the selected menu
are displayed.
♦ Select the appropriate language by pressing the ▲ or ▼ button.
Press the ENTER/OK button to confirm your choice.
If you change the language setting, the Subtitle Language, Audio Language, and the Teletext
Language of the Language menu (refer to page 40) are automatically changed to the selected
language.
The Subtitle Language, Audio Language, and the Teletext Language of the Language menu show
a list of languages supported by the current channel and the selection is highlighted. If you change
this language setting, the new selection is only valid for the current channel. The changed setting
does not change the setting of the Primary Subtitle Language, Primary Audio Language, or the
Primary Teletext Language of the Preference menu.
Teletext Decoder
Most set channels carry " teletext ", pages of written
information that provide information such as:
♦ Television programme times.
♦ News bulletins and Weather forecasts.
♦ Sports results.
♦ Subtitles for the hard of hearing.
The teletext pages are organized according to six categories:
Part
A
B
C
D
E
F
Contents
Selected page number.
Broadcasting station identity.
Current page number or search status.
Date and time.
Text.
Status information.
English - 41
Page 44
Displaying the Teletext Information
You can display teletext information at any time, but signal
reception must be good. Otherwise:
♦ Information may be missing.
♦ Some pages may not be displayed.
To activate the teletext mode and display the contents page:
Using the P ( ) or P ( ) button, select the channel providing
1.
the teletext service.
2. Press the TEXT/MIX () button to activate the teletext mode. The contents page is displayed. It can be redisplayed at any
time by pressing the MENU ( ) button.
3. Press the TEXT/MIX () button again. The actual broadcast will be displayed with "Teletext", "Double",
and "Mix" in order on the screen.
4. Press the TV/DTV button to exit from the Text display.
If any broken character appears while Text is being viewed,
make sure that the Text language is identical with the language
in the "Setup" menu mode. If both languages are different, select
the same language with the Text language on the "Setup" menu.
Selecting a Specic Teletext Page
Press the number buttons on the remote control to enter the
page number directly:
Enter the three-digit page number listed in the contents by pressing
1.
the corresponding numeric buttons.
2
. If the selected page is linked with several secondary pages, the
secondary pages are displayed in sequence. To freeze the display
on a given page, press the PIP ( ) . Press the PIP ( ) button
again to resume.
3. Using the various display options:
To display...
Both teletext information and the normal broadcast
Hidden text (answers to quiz games, for example)
The normal screen
A secondary page, by entering its 4-digit number
The next page
The previous page
Double-size letters in the:
Upper half of the screen
Lower half of the screen
Normal screen
Press the...
TEXT/MIX ()
INFO ( )
INFO ( )
PRE-CH ( )
P ( )
P
( )
P.SIZE
( )
Once
Twice
Three times
English - 42
Page 45
Using Fastext to Select a Teletext Page
The various topics included in the teletext pages are colour-coded,
and can be selected by pressing the coloured buttons on the
remote control.
Display the teletext contents page by pressing the TEXT/MIX
1.
() button.
2. Press the coloured button corresponding to the topic that you wish
to select
(The available topics are listed on the status information line).
3. Press the Red button to display the previous page.
Press the Green button to display the next page.
4. Press the TV/DTV button to exit from the Text display.
Setting Up Your Remote Control
After it has been set up properly, your remote control can operate in
five different modes: TV, DVD, Cable, Set-Top Box, VCR. Pressing the
corresponding button on the remote control allows you to switch
between these modes, and control whichever piece of equipment you
choose.
The remote control might not be compatible with all DVD Players,
VCRs, Cable boxes, and Set-Top Boxes.
Setting Up the Remote to Operate Your VCR, CABLE, DVD and STB
1. Turn off your VCR, CABLE, DVD and STB.
Press the VCR, CABLE, DVD and STB button on your TV’s remote
2.
control.
3. Press the SET button on your TV’s remote control.
4. Using the number buttons on your remote control, enter three digits of the
VCR code listed on pages 44~46 of this manual for your brand of VCR.
Make sure you enter three digits of the code, even if the first digit is a "0".
(If more than one code is listed, try the first one.)
5. Press the POWER button on the remote control.
Your VCR should turn on if your remote is set up correctly.
If your VCR does not turn on after set up, repeat steps 2, 3, and 4, but try
one of the other codes listed for your brand of VCR.
If no other codes are listed, try each VCR code, 000 through 080.
The Windows display-settings for a typical computer are shown below. The
actual screens on your PC may be different depending upon your particular
version of Windows and your particular video card. Even if your actual
screens look different, the same, basic set-up information will apply in almost
all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
1.
First, click on "Control Panel" on the Windows start menu.
2. When the control panel window appears, click on "Appearance and Themes"
and a display dialog-box will appear.
3. When the control panel window appears, click on "Display" and a display
dialog-box will appear.
4. Navigate to the "Settings" tab on the display dialog-box.
The correct size setting (resolution): Optimum- 1920 X 1080If a vertical-frequency option exists on your display settings dialog box, the correct value is
"60" or "60 Hz". Otherwise, just click "OK" and exit the dialog box.
Display Modes
Both screen position and size will vary depending on the type of PC monitor and its resolution.
The resolutions in the table are recommended. (All resolutions between the supported limits are supported)
D-Sub Input
Mode
IBM
VESA
VESA GTF
Resolution
640x350
720×400
640×480
640×480
640×480
800×600
800×600
800×600
1024×768
1024×768
1024×768
1152x864
1152x864
1280x960
1280×1024
1280×1024
1600×1200
1920×1080
640×480
800×600
1024×768
Horizontal
Frequency (kHz)
31.469
31.469
31.469
37.861
37.500
37.879
48.077
46.875
48.363
56.476
60.875
53.783
67.500
60.000
63.981
79.986
75.000
66.587
35.000
43.750
57.672
Vertical
Frequency (Hz)
70.086
70.087
59.940
72.809
75.000
60.317
72.188
75.000
60.004
70.069
75.029
59.959
75.000
60.000
60.020
75.025
60.000
59.934
70.000
70.000
72.000
Pixel Clock
Frequency (MHz)
25.175
28.322
25.175
31.500
31.500
40.000
50.000
49.500
65.000
75.000
78.750
81.750
108.000
108.000
108.000
123.000
162.000
138.500
28.560
45.500
78.434
Sync Polarity
(H/V)
+/-
-/+
-/-
-/-
-/+/+
+/+
+/+
-/-
-/+/+
-/+
+/+
+/+
+/+
+/+
+/+
+/-
-/+
-/+
-/-
HDMI/DVI Input
Mode
IBM
VESA
Resolution
640x350
720×400
640×480
800×600
1024×768
1280×1024
1920×1080
Horizontal
Frequency (kHz)
31.469
31.469
31.469
37.879
48.364
63.981
66.587
Vertical
Frequency (Hz)
70.086
70.087
59.940
60.317
60.004
60.020
59.934
Pixel Clock
Frequency (MHz)
25.175
28.322
25.175
40.000
65.000
108.000
138.500
The interlace mode is not supported.
The set might operate abnormally if a non-standard video format is selected.
Separate and Composite modes are supported. SOG is not supported.
Too long or low quality VGA cable can cause picture noise at high resolution modes
(1920x1080 or 1600x1200).
English - 47
Sync Polarity
(H/V)
+/-
-/+
-/-
+/+
-/-
+/+
+/-
Page 50
Setting the PC
Coarse and Fine Tuning of the Image (Image Lock):
The purpose of picture quality adjustment is to remove or
reduce picture noise.
If the noise is not removed by Fine-tuning alone, then adjust
TV
Coarse 50
Fine 0
Image Lock
the frequency as best as possible (coarse) and Fine-tune
again.
After the noise has been reduced, re-adjust the picture so that
it is aligned on the center of screen.
Preset: Press the SOURCE button to select PC mode.
1.
Press the MENU button to display the menu.
2.
Press the ▲ or ▼ button to select "Setup", then press the
Move Enter Return
ENTER/OK button.
3. Press the ▲ or ▼ button to select "PC", then press the ENTER/OK button.
4. Press the ENTER/OK button to select "Image Lock".
5. Press the ▲ or ▼ button to select "Coarse" or "Fine", then press the ENTER/OK button.
6. Press the ◄ or ► button to adjust the screen quality.
Press the ENTER/OK button.
7. Press the EXIT button to exit.
Changing the Image Position:
Adjust the PC’s screen positioning if it does not fit the TV
TV
Position
screen.
Follow the "Coarse and Fine Tuning of the Image
1.
(Image Lock)" instructions number 1 to 3.
2. Press the ▲ or ▼ button to select "Position", then press the ENTER/OK button.
3. Press the ▲ or ▼ button to adjusting the Vertical-Position.
Move Enter Return
Press the ◄ or ► button to adjust the Horizontal-Position.
Press the ENTER/OK button.
4. Press the EXIT button to exit.
Adjusting the PC Screen Automatically (Auto Adjustment):
Auto adjustment allows the PC screen of set to self-adjust to
the incoming PC video signal. The values of fine, coarse and
position are adjusted automatically.
Follow the "Coarse and Fine Tuning of the Image
1.
(Image Lock)" instructions number 1 to 3.
TV
Image Lock
Position
Auto Adjustment
Image Reset
PC
2. Press the ▲ or ▼ button to select "Auto Adjustment", then press the ENTER/OK button.
3. Press the EXIT button to exit.
Move Enter Return
Initializing the Image Settings (Image Reset):
You can replace all image settings with the factory default
values.
Follow the "Coarse and Fine Tuning of the Image
1.
(Image Lock)" instructions number 1 to 3.
TV
Image Lock
Position
Auto Adjustment
Image Reset
PC
2. Press the ▲ or ▼ button to select "Image Reset", then press the ENTER/OK button.
3. Press the EXIT button to exit.
Move Enter Return
English - 48
Page 51
Setting the Home Theatre PC
You can view higher quality pictures by configuring the
screen settings in PC Mode.
If you set the Home Theatre PC function to On, you can
configure the Detail Settings (when Picture Mode is
set to Standard or Movie) as in PC Mode.
Press the MENU button to display the menu.
1.
Press the ▲ or ▼ button to select "Setup", then press the
ENTER/OK button.
Press the ▲ or ▼ button to select "Home Theatre PC".
2.
Press the ENTER/OK button.
3. Press the ▲ or ▼ button to select "Off" or "On". Press the ENTER/OK button.
4. Press the EXIT button to exit.
This function is available only in PC mode.
TV
Plug & Play
Language : English
Time
Game Mode : Off
Blue Screen : Off
Melody : Off
PC
Home Theatre PC
Light Effect :
More
Move Enter Return
TV
Plug & Play
Language : English
Time
Game Mode : Off
Blue Screen : Off
Melody : Off
PC
Home Theatre PC
Light Effect :
More
Move Enter Return
Setup
: Off
Move Enter Return
Setup
: Off
Move Enter Return
In Watching TV
Off
In Watching TV
On
English - 49
Page 52
Using the WISELINK Function
This function enables you to view and listen to photo (JPEG)
and audio les (MP3) saved on a USB Mass Storage Class
(MSC) device.
Press the
Connect a USB device containing JPEG and/or MP3 les to
the WISELINK jack (USB jack) on the side of the TV.
If you enter the WISELINK mode with no USB device
connected the message “There is no device connected” will
appear. In this case, insert the USB device, exit the screen
by pressing the WISE LINK button on the remote control and
enter the WISELINK screen again.
Only alphanumeric characters must be used as a folder name or filename (photo, music).
The file system only supports FAT16/32 (The NTFS file system is not supported)
Certain types of USB Digital camera and audio devices may not be compatible with this TV.
Wiselink only supports the USB Mass Storage Class device (MSC). MSC is a Mass Storage Class
Bulk-Only Transport device. Examples of MSC are Thumb drives and Flash Card Readers (Both USB
HDD and HUB are not supported.)
Before connecting your device to the TV, please back up your files to prevent them from damage or loss
of data.SAMSUNG is not responsible for any data file damage or data loss.
Recommended image resolution for Wiselink is 600 mega pixels.
Please connect directly to the USB port of your TV. If you are using a separate cable connection, there
may be a USB Compatibility problem.
Only MP3 and JPEG file formats are supported.
The Wiselink mp3 format only supports music files with a high sampling frequency (32 kHz, 44.1 kHz, or
48 kHz).
We recommend the sequential jpeg format. Progressive jpeg uses a lot of memory and decoding may
fail.
Do not disconnect the USB device while it is “loading.”
Neither PTP (Picture Transfer Protocol) nor MTP (Media Transfer Protocol) is supported.
The playing duration of an mp3 file may be displayed as ‘00:00:00’ if its playing time information is not
found at the start of the file.
The higher the resolution of the image, the longer it takes to display on the screen.
If the horizontal resolution of an image is higher than 5000, it cannot be decoded.
If the vertical resolution of an image is higher than 4000, it cannot be decoded.
In the WISELINK mode, the
The Photo or Music List displays up to 300 folders or files.
POWER button on the remote control or front panel.
EXT 1(RGB) and EXT 2(AV) ports are disabled.
TV Side Panel
USB Drive
English - 50
Page 53
Using the WISELINK Menu
1. Press the MENU button. Press the ▲ or ▼ button to select
“Input”, then press the
2. Press the ▲ or ▼ button to select “WISELINK”, then press the
ENTER/OK button.
3. Press the ▲ or ▼ button to select the corresponding USB
Memory Device, then press the ENTER/OK button.
The "WISELINK" menu differs depending on the USB
➣
Memory Device connected to TV.
ENTER/OK button.
TV
Source List : TV ►
Edit Name ►
Anynet+ (HDMI-CEC)
WISELINK
Move Enter Return
STORAGE DEVICE
STORAGE DEVICE
STORAGE DEVICE
STORAGE DEVICE
Move Enter Exit
Input
Generio
4. Press the ◄ or ► button to move to an icon, then press the
ENTER/OK button.
To exit WISELINK mode, press the
➣
WISELINK button on
the remote control.
Press thePress the WISELINK button on the remote control to display a
WISELINK menu.
Using the Remote Control Button in WISELINK Menu
ButtonOperations
Move the cursor and select an item.
Select the currently selected item.
Play or pause the Slide Show or MP3 file.
Return to the previous menu.
Run various functions from the Photo and Music menus.
Stop the current slide show or MP3 file.
Page Up or Down (file list item)
Stop the current function and return to the previous high-level menu.
Music
XTICK
861MB/994MB Free
Move Enter Return
Stop WISELILNK mode. (Returns to TV mode )
English - 51
Page 54
Using the PHOTO (JPEG) List
This menu shows JPEG les and folders saved on an USB memory
device.
1. Complete Steps 1 to 3 of “Using the WISELINK Menu”. (Refer
to page 51)
2.
Press the ◄ or ► button to move to “Photo”, then press the
ENTER/OK button. The saved le information is displayed as a
folder or le.
3. Press the ▲, ▼, ◄ and ► buttons to select a le.
• Pressing the ENTER/OK button over a photo icon shows the
currently selected photo in full screen.
• Pressing the ENTER/OK button over a folder icon shows the
Photo
JPEG les included in the folder.
To exit WISELINK mode, press the
WISELINK button on the
remote control.
➣
Moving to a photo may take a few seconds to load the le.
At this point, the
icon will appear at the top left of
the screen.
➣
It takes time to show JPEG les as Thumbnail images.
➣
This menu only shows les whose le extension is jpg. Files of other formats such as bmp or tif
will not be displayed.
➣
The les are displayed on a page. 15 thumbnail photos are displayed per page.
The thumbnails are numbered from left to right and from top to bottom, from 1 to 15.
➣
Certain types of USB Digital camera and audio devices may not be compatible with this
➣
➣
Folders are displayed rst and they are followed by all JPEG les in the current folder
and JPEG les are sorted in alphabetical order.
If the photo is displayed in full screen, you can zoom in and out or rotate the photo on the screen.
➣
While a full screen is displayed, ◄ or ► button will let you see another photo image in the same
➣
folder.
Press the
➣
Photos without EXIF information may not be displayed as thumbnail images in the PHOTO LIST
➣
PLAY/PAUSE button when a Photo icon is selected to start a Slide Show.
depending on the picture quality and resolution.
Photo
XTICK
861MB/994MB Free
Move Enter Return
Up Folder
Forder1
File 4File 5File 6File 7File 8
File 9File 10File 11File 12File 13
Select Move Enter
Photo 0001 Photo 0001 None
INFO
Option Return
TV.
. The folders
1/10 Page
f
Viewing a Slide Show
4. Press the INFO button to display the option("Start Slide Show",
"Select All").
5. Press the ▲ or ▼ button to select “Start Slide Show” then press
the ENTER/OK button.
During the slide show, les are displayed in order from the
➣
currently shown le.
MP3 les can be automatically played during the Slide
➣
Show if the Default Background Music is set to On. To
enable this function, MP3 les and other photo les must be
located in the same folder on the USB Memory Device.
6. Press the INFO button during the slide show to set the
following options ("Slide Show Speed", "Background Music",
"Background Music Setting", "List"). Press the ▲ or ▼ button to
select the option, then press the ENTER/OK button.
• After setting the option press the ENTER/OK button to make
a change.
English - 52
Photo
Start Slide Show
Select All
INFO
Exit
Slide Show Speed : Fast
Background Music : On
Background Music Setting
List
INFO
Exit
Up Folder
Forder1
Photo 0001 Photo 0001 None
File 4File 5File 6File 7File 8
File 9File 10File 11File 12File 13
1/10 Page
Page 55
Using the Menu during a Slide Show
Slide Show Speed:
Select to control the slide show speed.
Press the ▲ or ▼ button to select the required option("Fast",
"Normal", Slow), then press the
ENTER/OK button.
Background Music:
Select to choose whether you want to play an MP3 le during a
slide show.
Press the ▲ or ▼ button to select the required option("On", "Off"),
then press the
ENTER/OK button.
Slide Show Speed : Fast
Fast
Normal
Background Music : On
Show
Background Music Setting
List
INFO
Exit
Slide Show Speed : Fast
Background Music : On
Off
Background Music Setting
On
List
INFO
Exit
Background Music Setting:
While the slide show is in progress, MP3 les and folders under the
same directory are displayed.
Select a folder using the ▲ or ▼ button and press the
ENTER/OK
button. The selected folder will be highlighted. Press the RETURN
button again to return to the slide show screen. The selected
background music is played.
If you turn Off the Background Music, even if the Background
➣
Music Settings have been set up, the background music will
not be played.
Photo
List:
The le information is displayed as a folder or JPEG le.
To exit WISELINK mode, press the
WISELINK button on the
remote control.
When selecting a photo le, the photo le information is
➣
Photo
displayed on the left side of the TV screen, such as the
resolution, the date modied and the order of the le in the
current directory (e.g. 10th out of 15).
: Folder icon
Such as the resolution
: Photo icon
: Move to the previous
modified
folder stage icon
English - 53
Background Music Setting
Choose a file for background music
Folder 01
Folder 02
Folder 03
Folder 04
Folder 05
Folder 06
◄◄ 1/1 Page ►►
Move Enter Return
Up Folder
Forder1
File 4File 5File 6File 7File 8
File 9File 10File 11File 12File 13
Select Move Enter
Up Folder
Forder1
File 4File 5File 6File 7File 8
File 9File 10File 11File 12File 13
Select Move Enter
Date
Order of the file
in thecurrent
directory
1/10 Page
Photo 0001 Photo 0001 None
INFO
Option Return
1/10 Page
Photo 0001 Photo 0001 None
INFO
Option Return
Photo
108 x 81
3KB
Dec20. 2006
4/25
Page 56
Using the Option Menu
1. Complete Steps 1 to 3 of “Using the WISELINK Menu”. (Refer
to page 51)
2. Press the ◄ or ► button to move to “Photo”, then press the
ENTER/OK button. The saved le information is displayed as a
folder or le.
3. Press the ▲, ▼, ◄ and ► button to select a le, then press the
ENTER/OK button. Pressing the button over a photo thumbnail
displays the photo in full screen.
Start Slide Show
Zoom : Original
Rotate : Original
List
4. Press the INFO button to display the option("Start Slide Show",
"Zoom", "Rotate", "List")
Zoom:
• Press the ▲ or ▼ button to select “Zoom”, then press the
ENTER/OK button.
• Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.(Original, X2, X4)
To pan up/down/left/right, press the ▲, ▼, ◄ and ► buttons.
➣
Images with a resolution larger than 1280 X 720 are not
➣
supported.
The "Rotate/Start Slide Show" option is disabled when the
➣
Start Slide Show
Zoom :
Rotate
List
"Zoom" option is selected.
Zoom function information icon (Displayed at the top left of the screen).
➣
"Original": Restore a photo to its original size.
➣
"X2": Zoom-in to a photo x2.
"X4": Zoom-in to a photo x4.
/ / /
: Move the zoomed-in photo up/down/right/left.
INFO
Exit
Original
x 2
x 4
INFO
Exit
Rotate:
Press the ▲ or ▼ button to select “Rotate”, then press the
•
ENTER/OK button.
Select the required option by pressing the ▲ or ▼ button, then
•
press the ENTER/OK button. (Original, 90, 180, 270)
The rotated le is not saved.
➣
The “Zoom/Start Slide Show” option is disabled when the
➣
“Rotate” option is selected.
The Rotating function information icon (Displayed at the top left
➣
of the screen).
"Original": This rotates a photo to its original position
➣
"90": This rotates a photo by 90 degrees
"180": This rotates a photo by 180 degrees
"270": This rotates a photo by 270 degrees
English - 54
Start Slide Show
Zoom : Original
Rotate :
List
INFO
Exit
Original
90
180
270
Page 57
Using the MP3 List
This menu shows MP3 les from among the les saved on a USB
memory device.
1. Complete Steps 1 to 3 of “Using the WISELINK Menu”. (Refer to
page 51)
2. Press the ◄ or ► button to move to “Music”, then press the
ENTER/OK button. The saved le information is displayed as a
folder or le.
3. Press the ▲ or ▼ button to move to an icon, then press the
ENTER/OK button.
•
Pressing the
immediately plays the music le.
Pressing the ENTER/OK button over a folder icon shows the
•
music les included in the folder.
To select a le on the next page, press the REW ◄◄ or FF
•
►► button to move to the next page.
4. To select all les or a le, press the INFO button to display the
Music menus. Press the ENTER/OK button to select “Play”,
“Repeat Music” or “Select All”.
To exit WISELINK mode, press the
remote control.
ENTER/OK button over a musical note icon
WISELINK button on the
Play
Repeat Music : On
Select All
XTICK
861MB/994MB Free
Move Enter Return
Music
Nat King Cole-Fly me to
Upper Folder
Folder 1
001 Swan Song feat.TBNY
002 Beatles-Yesterday
003 Fall in Love
004 Tom Waits-Time
005 Chuk Mangione-Feel So good
006 Nat King Cole-Fly me to the moon
007 Ryuichi Sakamoto-Rain
INFO
Select Move Enter
008 Bon jovi-This ain’t a love song
Exit
: Folder icon
: Music icon
Music
INFO
Option Return
1/10 Page
00:04:00
00:04:01
00:04:28
00:04:12
00:05:39
00:04:30
00:04:30
00:03:54
00:05:25
Using the Option Menu
Play:
: Move to the previous
folder stage icon
Select to play MP3 les.
Press the
➣
Press the STOP ▄ button to exit Play mode.
➣
This menu only shows les with the MP3 le extension. Files with other le extensions are not
➣
PLAY/PAUSE button while playing an MP3 le to pause the le.
displayed,even if they are saved on the same USB device.
The selected le is displayed on the top with its playing time.
➣
To adjust the music volume, press the
➣
sound, press the
FF ►► or REW ◄◄ button does not function during the play.
➣
MUTE button on the remote control.
VOL+ or VOL- button on the remote control. To mute the
Repeat Music:
Select to repeatedly play MP3 les in the current folder.
You can select On or Off
Music function information icon
: When all music les are being played.
: When a music le is being played.
: When pressing the PLAY/PAUSE button on the remote control while music is
/
playing. The music stops and the ‘Play’ text appears at the top of the screen.
: When pressing the STOP▄ button on the remote control when music is stopped. The music
resumes and the ‘Stop’ text appears at the top of the screen.
English - 55
Page 58
Using the Setup Menu
Setup displays the user settings of the WISELINK menu.
1. Complete Steps 1 to 3 of “Using the WISELINK Menu”. (Refer to page 51)
2. Press the ◄ or ► button to move to “Setup”, then press the
3. Press the ▲ or ▼ button to select an item you want, then press the ENTER/OK button. (“Slide Show
Speed”, “Background Music”, “Background Music Setting”, “Repeat Music”, “Screen Saver”)
4. Press the ▲ or ▼ button to select the option, then press the ENTER/OK button.
To exit WISELINK mode, press the WISELINK button on the remote control.
Slide Show Speed:
Select to control the slide show speed. You can select “Fast”,
“Normal” or “Slow”.
Background Music :
Select to determine whether to play an MP3 le during a slide
show. You can select Music “On” or Music “Off”.
Background Music Setting:
While a slide show is in progress, use the "Background Music
Setting" to select a music le to listen to. Select an MP3 le as the
background music.
Repeat Music:
Select to determine whether to repeat playing the music when all
MP3 les in the current folder have been played.
ENTER/OK button.
Setup
Setup
Background Music Setting
Choose a file for background music
Folder 01
Folder 02
Folder 03
Folder 04
Folder 05
Folder 06
Setup
Slide Show Speed : Fast
Background Music : On
Background Music Setting
Repeat Music : Off
Screen Saver : 5 min
Slide Show Speed : Fast
Background Music : On
Background Music Setting
Repeat Music : Off
Screen Saver : 5 min
◄◄ 1/1 Page ►►
Move Enter Return
Slide Show Speed : Fast
Background Music : On
Background Music Setting
Repeat Music :Off
Screen Saver :5 min
Fast
Normal
Slow
Move Enter Return
Off
On
Move Enter Return
Off
On
Screen Saver:
Select to set the waiting time before the screen saver appears. The
screensaver will appear when no button is pressed for 1, 5 or 10
minutes.
English - 56
Setup
Move Enter Return
Slide Show Speed : Fast
Background Music : On
Background Music Setting
Repeat Music : Off
Screen Saver : 5 min
Move Enter Return
1 min
5 min
10 min
Page 59
What is Anynet+?
Anynet+ is an AV network system that enables an easy-to-use AV interface for users by controlling
all connected AV devices through the Anynet+ menu when Samsung Electronics AV devices are
connected.
Connecting Anynet+ Devices
The Anynet+ system supports AV devices supporting Anynet+ only.
Check if there is an Anynet+ mark on the AV device to be connected to the TV.
Connect the [HDMI 1], [HDMI
2] or [HDMI 3] jack on the TV
and the HDMI OUT jack of the
corresponding Anynet+ device
using the HDMI cable.
HDMI 1.3 Cable
HDMI 1.3 Cable
HDMI 1.3 Cable
To connect to Home Theater
TV
1. Connect the [HDMI 1],
[HDMI 2] or [HDMI 3]
jack on the TV and the
Anynet+ Device 1Anynet+ Device 2
HDMI OUT jack of the
corresponding Anynet+
device using the HDMI
cable.
2.
Connect the HDMI IN jack
HDMI 1.3 Cable
Home Theatre
HDMI 1.3 Cable
Anynet+ Device 3
of the home theatre and
the HDMI OUT jack of the
corresponding Anynet+
device using the HDMI
cable.
HDMI 1.3 Cable
Optical Cable
Connect only the optical cable between [Digital Audio Out (Optical)] on your TV and Digital Audio
➣
HDMI 1.3 Cable
Input on the receiver.
Connect only one receiver.
➣
You can listen to 5.1 channel sound through the home theatre’s speakers. Otherwise, you can only
➣
listen to 2 channel stereo sound in other cases. Make sure to connect the Digital Audio IN (Optical) of
the home theatre and the TV correctly to listen to TV sound through the home theatre. However, you
cannot listen to sound from the BD recorder that is sent to the home theatre via the TV in 5.1 channel
sound because the TV outputs only 2 channel stereo sound. Please see the manual for the home
theatre.
You can connect an Anynet+ device using the HDMI 1.3 cable. Some HDMI cables may not support
➣
Anynet+ functions.
Anynet+ works when the AV device supporting Anynet+ is in the Standby or On status.
➣
Anynet+ supports up to 8 AV devices in total.
➣
English - 57
Page 60
Setting Up Anynet
+
The following settings are to use Anynet+ functions.
Using the Anynet+ Function
1. Press the Anynet+ button.
Press the ▲ or ▼ button to select Setup, then press the
ENTER/OK button.
2. Press the ENTER/OK button to select Anynet+ (HDMI-CEC),
then press the ENTER/OK button.
3. Press the ▲ or ▼ button to select On, then press the
ENTER/OK button.
The Anynet+ (HDMI-CEC) function is enabled.
➣
If you select Off, Anynet+ (HDMI-CEC) is disabled.
➣
When the Anynet+ (HDMI-CEC) function is disabled, all the
➣
Anynet+ related operations are deactivated.
View TV
Select Device
Record
Menu on Device
Device Operation
Receiver :Off
Setup
Move
Enter
Exit
Setup
Anynet+ (HDMI-CEC)
Auto Turn Off
Searching Connections
: Off
: Off
Off
On
EnterReturnMove
Turning an Anynet+ Device Off Automatically when the TV is Turned Off
1. Press the ▲ or ▼ button to select Auto Turn Off, then press
the ENTER/OK button.
2. Press the ▲ or ▼ button to select On, then press the
ENTER/OK button.
The Auto turn off function is enabled.
➣
If you select Off, the Auto turn off function is canceled.
➣
Press the EXIT button to exit.
The Select Device setting of the TV remote control is to be set
➣
Anynet+ (HDMI-CEC)
Auto Turn Off
Searching Connections
Move
Setup
: On
: Off
Off
On
EnterReturn
to TV to use the Anynet+ function.
If you set Auto Turn Off to On, connected external devices are also turned off when the TV is turned
➣
off. However, if the device is recording, it may not be turned off.
Scanning and Switching between Anynet+ Devices
1. Press the Anynet+ button.
2. Press the ▲ or ▼ button to select Select Device, then press
the ENTER/OK button.
3. Press the ▲ or ▼ button to select to a particular device and
press the ENTER/OK button.
It is switched to the selected device.
4. If you cannot find a device you want, press the ▲ or ▼ button
to select Searching Connections, then press the ENTER/OK
button.
The meassage Configuring Anynet+ connection... is
displayed. When searching devices completes, the connected
devices are listed in the Anynet+ menu.
Switching to the selected devices may take up to 2 minutes.
➣
You cannot cancel the operation during the switching
operation.
The time required to scan for devices is determined by the
➣
number of connected devices.
When the device scan is complete, the number of found
➣
devices is not displayed.
Although the TV automatically scans devices when it is turned on using the POWER button, devices
➣
connected when the TV is on or under a specic circumstance are not displayed in the device list.
Therefore select Searching Connections menu to search devices.
If you have selected external input mode by pressing the SOURCE button, you cannot use the
➣
Anynet+ function. Make sure to switch to an Anynet+ device by using the Anynet+ button.
English - 58
TVP9
View TV
Select Device
Record
Menu on Device
Device Operation
Receiver :Off
Setup
Move
Enter
Return
Anynet+ (HDMI-CEC)
Auto Turn Off
Searching Connections
: On
Setup
: On
EnterReturnMove
DVDR1
DVDR2
DVD1
DVD2
Page 61
Anynet+ Menu
The Anynet+ menu changes depending on the type and status of the Anynet+ devices connected
to the TV.
Anynet+ MenuDescription
View TVSwitches from Anynet+ to TV broadcast mode.
Select DeviceYour TV connects to the corresponding device.
RecordStarts a recording. (This menu works only for a device supporting
Menu on DeviceShows the menu of the connected device.
Device OperationShows the play control menu of the connected device.
ReceiverSound is output through the receiver.
SetupYou can set the environment for using Anynet+.
TV Remote Control Buttons Available in Anynet+ Mode
Device TypeOperating StatusAvailable Buttons
Anynet+ Device
Device with built-in Tuner
Audio DeviceWhen Receiver is activated
Anyview2When watching TV►
➣
The Anynet+ function only works when the remote control is set to TV.
➣
REC button works only while in the recordable state.
The
➣
You cannot control Anynet+ devices using the buttons on the side of the TV. You can control Anynet+
devices only using the TV remote control.
The TV remote control may not work under certain conditions. In this case, re-select the Anynet+
➣
device.
The Anynet+ functions don’t operate for the products from other manufacturers.
➣
In Anynet+ mode, the colour buttons may not work properly.
➣
The ◄◄, ►► operations may differ depending on the device.
➣
recording.)
Example. When a DVD Recorder is connected, the DVD Recorder’s
title menu appears.
Example. When a DVD Recorder is connected, the play control
menu of the DVD Recorder appears.
After switching to the
device, when the menu of
the corresponding device is
displayed on the screen.
After switching to the device,
while playing a file
After switching to the device,
when you are watching a TV
programme
Numeric buttons
▲/▼/◄/►/
Colour buttons
EXIT button
◄◄(Backward search)
►►(Forward search)
(Stop)
►
CH ▲/▼ button
VOL +/- button
MUTE button
ENTER/OK buttons
(Play/Pause)
(Play/Pause)
Recording
You can make a recording of a TV programme using a recorder.
Press the
Recording begins. (Only when the Anynet+ enabled recording device is connected.)
➣
➣
➣
REC button.
The current TV programme is recorded in the Watching TV status. If you are watching video from
another device, the video from the device is recorded.
You can also record the source streams by selecting Record after pressing the Anynet+ button.
Before recording, check whether the antenna jack is properly connected to the recording device. For
the antenna connection to the recording device, refer to its user manual.
English - 59
Page 62
Listening through a Receiver
You can listen to sound through a receiver instead of the TV speaker.
Press the Anynet+ button.
1.
Press the ▲ or ▼ button to select Receiver, then press the
ENTER/OK button.
Press the ◄ or ► button to select to On, then press the
2.
ENTER/OK button.
Now you can listen to sound through the receiver.
3. Press the EXIT button to exit.
➣
When the receiver is set to On, you can listen to the TV sound
through the 2-channel receiver.
If the receiver is exclusively for a home theatre only (supporting
➣
TVP9
View TV
Select Device
Record
Menu on Device
Device Operation
Receiver :On
Setup
Move
Exit
Enter
audio only), it may not appear in the device list.
Only when you have connected the optical jack of the TV and the receiver properly, does Receiver
➣
work.
In case of a content with copyright problem, listening through the receiver may not properly operate.
➣
When listening through the receiver, there are restrictions for using the PIP and audio-related menu.
➣
Check Points before Requesting Service
SymptomSolution
Anynet+ does not
work.
I want to start
Anynet+.
I want to exit Anynet+.
The Connecting to
Anynet+ device…
message appears on
the screen.
The Anynet+ device
does not play.
The connected device
is not displayed.
The TV programme
cannot be recorded.
The TV sound is not
output through the
receiver.
■ Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+
devices only.
■ Connect only one receiver.
■ Check if the Anynet+ device power cord is properly connected.
■ Check the Anynet+ device’s Video/Audio/HDMI 1.3 cable connections.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
■ Check whether the TV remote control is in TV mode.
■ Check whether it is Anynet+ exclusive remote control.
■ Anynet+ doesn’t work at a certain condition. (Searching channels)
■ When connecting or removing the HDMI 1.3 cable, please make sure to search
devices again or restart your TV.
■ Check if the Anynet+ Function of Anynet+ device is set on.
■ Check if the Anynet+ device is properly connected to the TV and check if the
Anynet+ (HDMI-CEC) is set to On in the Anynet+ Setup menu.
■ Press the TV button on the TV remote control to switch to TV. Then press the
Anynet+ button to show the Anynet+ menu and select a menu you want.
■ Select View TV in Anynet+ menu.
■ Press the SOURCE button on the TV remote control and select a device other
than Anynet+ devices.
■ Press any of CH, CH LIST, PRE-CH, and such to change to the
TV mode. (Note that the channel button operates only when a tuner-embedded
Anynet+ device is not connected.)
■ You cannot use the remote control when you are configuring Anynet+ or
switching to a view mode.
■ Use the remote control when the Anynet+ setting or switching to view mode is
complete.
You cannot use the play function when Plug & Play is in progress.
■ Check whether or not the device supports Anynet+ functions.
■ Check whether or not the HDMI 1.3 cable is properly connected.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
■ Search Anynet+ devices again.
■ You can connect an Anynet+ device using the HDMI 1.3 cable only. Some HDMI
cables may not support Anynet+ functions.
Check whether the antenna jack on the recording device is properly connected.
Connect the optical cable between TV and the receiver.
English - 60
Page 63
Wall-Mount Adjustment (Sold separately)
Once the wall mount is installed, the position of your TV can be easily adjustable.
TV Rear PanelAuto Wall-Mount
SERVICE Cable (Not supplied)
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select “Setup”, then press the
ENTER/OK button.
2. Press the ▲ or ▼ button to select “Wall-Mount Adjustment”, then press the ENTER/OK button.
TV
More
Wall-Mount Adjustment
Energy Saving : Off
HDMI Black Level
PIP
SW Upgrade
3. Adjust to the desired position using the ▲,▼,◄,► buttons.
4. Press the EXIT button to exit.
If you press an arrow button when no OSD is displayed on the
TV screen, the Adjustment screen appears.
When you turn the power off, your TV moves to the initial
installation position.
Move Enter Return
Wall Mount Adjusment
Position1
When you turn the power on, your TV moves to the last
remembered position you adjusted.
The auto wall mount will not work when Anynet+ is operating.
Position 1 2 3
Adjust Center Exit
INFO
Using the Remote Control Buttons
ButtonOperations
Wall-mount angle
adjustment
ResetMoves to the initial installation position
Remembering the
position and
red
button
green
button
yellow
button
moving to the
remembered
position
For installation, refer to the Installation Manual provided.
For product installation and the installation and moving of the wall mount, make sure to consult a
specialized installation company.
This installation manual is to be used when attaching the wall mount to a wall.
When attaching to other building materials, please contact your nearest dealer
Tilt Up, Tilt Down, Move right, Move left
1. Select the Direction buttons of the remote control.
2. Press the red button (Select Position 1).
3. Adjust the set to a desired position following the wall mount owner's
manual.
4. The position you adjusted last is memorized as Position 1.
5. By using the green button (Select Position 2) and the yellow button
(Select Position 3), you can save positions according to the
procedures above.
6. You can save 3 respective positions. To the red button (Select
Position 1), green button (Select Position 2) and yellow button
(Select Position 3). If you press a button after saving, the set
automatically moves to that saved angle.
7. If you additionally move the set from a saved position, the last
position is saved.
Setup
: Low
English - 61
Page 64
Using the Anti-Theft Kensington Lock (depending on the model)
The Kensington lock is a device used to physically fix the system when using it in a public place.
The locking device has to be purchased separately. The appearance and locking method may
differ from the illustration depending on the manufacturer. Please refer to the manual provided
with the Kensington lock for proper use.
1.
Insert the locking device into
the Kensington slot on the
LCD TV (Figure 1), and turn it in the locking direction
(Figure 2).
2. Connect the Kensington lock
cable.
3. Fix the Kensington lock to a
desk or a heavy stationary
object.
Cable
Figure 2
Figure 1
<Optional>
The place of the Kensington Lock may be
different depending on its model.
Troubleshooting: Before Contacting Service Personnel
No sound or picture
Normal picture but no sound
Screen is black and power
indicator light blinks steadily
No picture or black and
white picture
Sound and picture
interference
Blurred or snowy picture,
distorted sound
Remote control malfunctions
"Check signal cable."
message is displayed.
On PC mode, "Not Supported
Mode." message is displayed.
The damaged picture appears
in the corner of the screen.
The TFT LCD panel uses a panel consisting of sub pixels (6 220 800) which require sophisticated
technology to produce. However, there may be few bright or dark pixels on the screen. These pixels will
have no impact on the performance of the product.
Check that the mains lead has been connected to a wall socket.
Check that you have pressed the button on the front of the set.
Check the picture contrast and brightness settings.
Check the volume.
Check the volume.
Check whether the MUTE button has been pressed on the remote control.
Check if "Internal Mute" is off
On your computer check; Power, Signal Cable.
The TV is using its power management system.
Move the computer’s mouse or press any key on the keyboard.
Adjust the colour settings.
Check that the broadcast system selected is correct.
Try to identify the electrical appliance that is affecting the set and move it
further away.
Plug your set into a different mains socket.
Check the direction, location and connections of your aerial.
This interference is often due to the use of an indoor aerial.
Replace the remote control batteries.
Clean the upper edge of the remote control (transmission window).
Check the battery terminals.
Check that the signal cable is firmly connected to the PC or video sources.
Check that the PC or video sources are turned on.
Check the maximum resolution and the frequency of the video adaptor.
Compare these values with the data in the Display Modes.
If "Just Scan" is selected in some external devices, the damaged picture
may appear in the corner of the screen. This symptom is caused by external
devices, not TV.
English - 62
Page 65
Technical and Environmental Specications
Model Name
Screen Size (Diagonal)
PC Resolution
Sound
Output
Dimensions (WxDxH)
Body
With stand
Weight
With stand
Environmental Considerations
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
Design and specifications are subject to change without prior notice.
This device is a Class B digital apparatus.
For the power supply and Power Consumption, refer to the label attached to the product.
LE40F8LE46F8
40 inch46 inch
1920 x 1080 @ 60 Hz1920 x 1080 @ 60 Hz
10 W X 210 W X 2
1094 x 103 x 607 mm
1094 x 290 x 675 mm
24 kg33 kg
10 °C to 40 °C (50 °F to 104 °F)
10 % to 80 %, non-condensing
-20 °C to 45 °C (-4 °F to 113 °F)
5 % to 95 %, non-condensing
1222 x 111 x 687 mm
1222 x 320 x 752 mm
10 °C to 40 °C (50 °F to 104 °F)
10 % to 80 %, non-condensing
-20 °C to 45 °C (-4 °F to 113 °F)
5 % to 95 %, non-condensing
Stand Swivel (Left / Right)
-20˚ ~ 20˚
English - 63
Page 66
Warning! Important Safety Instructions
Please read the appropriate section that corresponds to the marking on your Samsung product before
attempting to install the product.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). THERE ARE
NO USER SERVICEABLE PARTS INSIDE. REFER ALL
SERVICING TO QUALIFIED PERSONNEL.
• The slots and openings in the cabinet and in the back or bottom are provided for necessary ventilation.
To ensure reliable operation of this apparatus, and to protect it from overheating, these slots and openings must never
be blocked or covered.
- Do not cover the slots and openings with a cloth or other materials.
- Do not block the slots and openings by placing this apparatus on a bed, sofa, rug or other similar surface.
- Do not place this apparatus in a confined space, such as a bookcase, or built-in cabinet, unless proper ventilation is
provided.
- Give your product 10 cm (4 inch) clearance from the wall.
• Do not place this apparatus near or over a radiator or heat resistor, or where it is exposed to direct sunlight.
• Do not place heat generating items such as candles, ashtrays, incense, flammable gas or explosive materials near the
product.
• Do not place a water containing vessel on this apparatus, as this can result in a risk of fire or electric shock.
• Do not expose this apparatus to rain or place it near water(near a bathtub, washbowl, kitchen sink, or laundry tub,
in a wet basement, or near a swimming pool etc.). If this apparatus accidentally gets wet, unplug it and contact an
authorized dealer immediately. Make sure to pull out the power cord from the outlet before cleaning.
• This apparatus use batteries. In your community there might be regulations that require you to dispose of these
batteries properly under environmental considerations. Please contact your local authorities for disposal or recycling
information.
• Do not overload wall outlets, extension cords or adaptors beyond their capacity, since this can result in fire or electric
shock.
• Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or
against them,
paying particular attention to cords at plug end, adaptors and the point where they exit from the appliance.
• To protect this apparatus from a lightning storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable system.
This will prevent damage to the set due to lightning and power line surges.
• Before connecting the AC power cord to the DC adaptor outlet, make sure the voltage designation of the DC adaptor
corresponds to the local electrical supply.
• Never insert anything metallic into the open parts of this apparatus. Doing so many create a danger of electric shock.
• To avoid electric shock, never touch the inside of this apparatus. Only a qualified technician should open this
apparatus.
• Make sure to plug the power cord in until it is firmly inserted. When removing the power cord, make sure to hold the
power plug when pulling the plug from the outlet. Do not touch the power cord with wet hands.
• If this apparatus does not operate normally - in particular, if there are any unusual sounds or smells coming from it
- unplug it immediately and contact an authorized dealer or service center.
• Be sure to pull the power plug out of the outlet if the TV is to remain unused or if you are to leave the house for an
extended period of time (especially when children, elderly or disabled people will be left alone in the house).
- Accumulated dust can cause an electric shock, an electric leakage or a fire by causing the power cord to generate
sparks and heat or the insulation to deteriorate.
• Be sure to contact an authorized service center, when installing your set in a location with heavy dust, high or low
temperatures,high humidity, chemical substances and where it operates for 24 hours such as the airport, the train
station etc. Failure to do so may cause serious damage to your set.
• Use only a properly grounded plug and receptacle.
- An improper ground may cause electric shock or equipment damage. (Class l Equipment only.)
• To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains
plug shall be readily operable.
• Do not allow children to hang onto the product.
• Store the accessories (battery, etc.) in a location safely out of the reach of children.
• Do not install the product in an unstable location such as a shaky self, a slanted floor or a location exposed to vibration.
• Do not drop or impart any shock to the product. If the product is damaged, disconnect the power cord and contact a
service center.
This symbol indicates that high voltage is
present inside. It is dangerous to make any
kind of contact with any internal part of this
product.
This symbol alerts you that important literature
concerning operation and maintenance has
been included with this product.
WARNING - TO PREVENT THE SPREAD OF FIRE,
•
KEEP CANDLES OR OTHER OPEN FLAMES
AWAY FROM THIS PRODUCT AT ALL TIMES.
Page 67
Wiring the Mains Power Supply Plug (UK Only)
IMPORTANT NOTICE
The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is
indicated on the pin face of the plug and, if it requires replacing, a fuse approved to BSI1362 of the same rating
must be used.
Never use the plug with the fuse cover omitted if the cover is detachable. If a replacement fuse cover is required,
it must be of the same colour as the pin face of the plug. Replacement covers are available from your dealer.
If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach
a power point, you should obtain a suitabl y approved extension lead or consult your dealer for assistance.
However, if there is no alternative but to cut off the plug, remove the fuse and then safely dispose of the plug.
Do NOT connect the plug to a mains socket as there is a risk of shock hazard from the bared flexible cord.
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:
BLUE - NEUTRAL BROWN - LIVE
As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as
follows :
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or
BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured
BROWN or RED.
WARNING:
DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL, WHICH IS MARKED WITH THE
LETTER E OR BY THE EARTH SYMBOL , OR COLOURED GREEN OR GREEN AND YELLOW.
Warranty Card
UNITED KINGDOM
This Samsung product is warranted for a period of twelve (12) months from the original date of purchase, against
defective materials and workmanship. In the event that warranty service is required, you should return the
product to the retailer from whom it was purchased. However, Samsung Authorised Dealers and Authorised
Service Centres in other EC Countries will comply with the warranty on the terms issued to purchasers in the
country concerned. In case of difficulty, details of our Authorised Service Centres are available from:
1. The warranty is only valid if, when warranty service is required, the warranty card is fully and properly
completed and is presented with the original invoice or sales slip or confirmation, and the serial number on
the product has not been defaced.
2. Samsung’s obligations are limited to the repair or, at its discretion, replacement of the product or the
defective part.
3. Warranty repairs must be carried out by Authorised Samsung Dealers or Authorised Service Centres.
No re-imbursement will be made for repairs carried out by non Samsung Dealers and, any such repair work
and damage to the products caused by such repair work will not be covered by this warranty.
4. This product is not considered to be defective in materials nor workmanship by reason that it requires
adaptation in order to conform to national or local technical or safety standards in force in any Country other
than the one for which the product was originally designed and manufactured.
Page 68
This page is intentionally
left blank.
Page 69
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at
the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal,
please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material
resources. Household users should contact either the retailer where they purchased this product, or their local
government office, for details of where and how they can take this item for environmentally safe recycling. Business users
should contact their supplier and check the terms and conditions of the purchase contract. This product should not be
mixed with other commercial wastes for disposal.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.