Samsung Electronics owns the copyright for this manual.
Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited.
Trademarks other than that of Samsung Electronics are owned by their respective owners.
(For India Only)
This product is RoHS compliant.
For more information on safe disposal and recycling visit our
website www.samsung.com/in or contact our Helpline numbers -
1800 40 SAMSUNG(1800 40 7267864) (Toll-Free)
Table of contents
Before Using the Product
Securing the Installation Space 4
Safety Precautions 4
Cleaning 5
Electricity and Safety 5
Installation 6
Operation 7
Preparations
Parts 9
Control Panel 9
Function Key Guide 10
Changing Brightness, Contrast and Sharpness
settings 12
Changing the Volume setting 12
Types of Ports 13
Adjusting the Product Tilt 13
Anti-theft Lock 14
Precautions for moving the product 14
Installation 15
Attaching the Stand 15
Removing the Stand 16
Connecting and Using a Source Device
Read below before installing the product. 17
Connecting and Using a PC 17
Connection Using the HDMI Cable 17
Connection Using an HDMI-DVI Cable 17
Connection Using an DP Cable 18
Connecting to Headphones 18
Connecting the Power 18
Correct posture to use the product 19
Driver Installation 19
Setting Optimum Resolution 19
Game
Picture Mode 20
Refresh Rate 21
Black Equalizer 21
Response Time 21
FreeSync 22
Low Input Lag 23
Picture
Picture Mode 26
Brightness 27
Contrast 27
Sharpness 27
Color 27
HDMI Black Level 28
Eye Saver Mode 28
Screen Adjustment 28
OnScreen Display
Language 29
Display Time 29
Screen Size 23
Virtual Aim Point 24
2
Table of contents
System
Self Diagnosis 30
Volume 31
Smart ECO Saving+ 31
Off Timer Plus 32
PC/AV Mode 32
DisplayPort Ver. 32
HDMI Mode 32
Source Detection 32
Key Repeat Time 33
Power LED On 33
Reset All 33
Information
Information 34
Installing the Software
Easy Setting Box 35
Restrictions and Problems with the Installation 35
Upgrade by downloading the firmware from the
website 35
System Requirements 35
Troubleshooting Guide
Requirements Before Contacting Samsung Customer
Service Centre 36
Monitor diagnosis (Screen issue) 36
Checking the Resolution and Frequency 36
Check the following. 36
Q & A 38
Specifications
General 39
Standard Signal Mode Table 40
Appendix
Responsibility for the Pay Service (Cost to
Customers) 42
Not a product defect 42
A Product damage caused by customer's fault 42
Others 42
3
Chapter 01
Before Using the Product
Securing the Installation Space
Make sure to have enough space for ventilation when placing the product. An internal temperature rise
may cause fire and damage the product. Maintain enough space around the product as shown in the
diagram when installing the product.
―
The exterior may differ depending on the product.
10 cm
10 cm
10 cm10 cm
10 cm
Safety Precautions
Warning
Caution
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). THERE ARE
NO USER SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO QUALIFIED PERSONNEL.
This symbol indicates that high voltage
is present inside. It is dangerous to
make any kind of contact with any
internal part of this product.
This symbol indicates that this
product has included important
literature concerning operation and
maintenance.
Class II product: This symbol indicates
that a safety connection to electrical
earth (ground) is not required. If this
symbol is not present on a product
with a mains lead, the product
MUST have a reliable connection to
protective earth (ground).
A serious or fatal injury may result if instructions are not followed.
Personal injury or damage to properties may result if instructions are
not followed.
CAUTION
RISK OF ELECTRIC SHOCK. DO NOT OPEN.
AC voltage: Rated voltage marked with
this symbol is AC voltage.
DC voltage: Rated voltage marked with
this symbol is DC voltage.
Caution. Consult instructions for use:
This symbol instructs the user to
consult the user manual for further
safety related information.
4
Cleaning
Electricity and Safety
High-glossy models can develop white stains on the surface if an ultrasonic wave humidifier is used
nearby.
―
Contact your nearest Samsung Customer Service Centre if you want to clean the inside of the product (Service
fee will be charged.)
―
Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched.
―
Take the following steps when cleaning.
Power off the product and PC.
1
Disconnect the power cord from the product.
2
―
Hold the power cable by the plug and do not touch the cable with wet hands. Otherwise, an electric shock
may result.
Wipe the product with a clean, soft and dry cloth.
3
‒ Do not apply a cleaning agent that contains alcohol, solvent, or surfactant to the product.
‒ Do not spray water or detergent directly on the product.
Wet a soft cloth in water, wing it out well, and then use the cloth to wipe the exterior of the product
4
clean.
Connect the power cord to the product when cleaning is finished.
5
Power on the product and PC.
6
Warning
• Do not use a damaged power cord or plug, or a loose power socket.
• Do not use multiple products with a single power socket.
• Do not touch the power plug with wet hands.
• Insert the power plug all the way in so it is not loose.
• Connect the power plug to a grounded power socket (type 1 insulated devices only).
• Do not bend or pull the power cord with force. Be careful not to leave the power cord under a heavy
object.
• Do not place the power cord or product near heat sources.
• Clean any dust around the pins of the power plug or the power socket with a dry cloth.
Caution
• Do not disconnect the power cord while the product is being used.
• Only use the power cord provided with your product by Samsung. Do not use the power cord with
other products.
• Keep the power socket where the power cord is connected unobstructed.
‒ The power cord must be disconnected to cut off power to the product when an issue occurs.
• Hold the plug when disconnecting the power cord from the power socket.
5
Installation
Warning
• DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF THE PRODUCT. DO NOT
INSTALL THE PRODUCT NEAR HEAT SOURCES.
• Do not install the product in poorly ventilated spaces such as a bookcase or closet.
• Install the product at least 10cm away from the wall to allow ventilation.
• Keep the plastic packaging out of the reach of children.
‒ Children may suffocate.
• Do not install the product on an unstable or vibrating surface (insecure shelf, sloped surface, etc.)
‒ The product may fall and become damaged and/or cause an injury.
‒ Using the product in an area with excess vibration may damage the product or cause a fire.
• Do not install the product in a vehicle or a place exposed to dust, moisture (water drips, etc.), oil, or
smoke.
• Do not expose the product to direct sunlight, heat, or a hot object such as a stove.
‒ The product lifespan may be reduced or a fire may result.
• Do not install the product within the reach of young children.
‒ The product may fall and injure children.
• Edible oil, such as soybean oil, can damage or deform the product. Do not install the product in a
kitchen or near a kitchen counter.
Caution
• Do not drop the product while moving.
• Do not set down the product on its front.
• When installing the product on a cabinet or shelf, make sure that the bottom edge of the front of the
product is not protruding.
‒ The product may fall and become damaged and/or cause an injury.
‒ Install the product only on cabinets or shelves of the right size.
• Set down the product gently.
‒ Product failure or personal injury may result.
• Installing the product in an unusual place (a place exposed to a lot of fine dust, chemical substances,
extreme temperatures or a significant presence of moisture, or a place where the product will
operate continuously for an extended period of time) may seriously affect its performance.
‒ Be sure to consult Samsung Customer Service Centre if you want to install the product at such a
place.
6
Operation
Warning
• There is a high voltage inside the product. Never disassemble, repair or modify the product yourself.
‒ Contact Samsung Customer Service Centre for repairs.
• To move the product, first disconnect all the cables from it, including the power cable.
• If the product generates abnormal sounds, a burning smell or smoke, disconnect the power cord
immediately and contact Samsung Customer Service Centre.
• Do not let children hang from the product or climb on top of it.
‒ Children may become injured or seriously harmed.
• If the product is dropped or the outer case is damaged, turn off the power and disconnect the power
cord. Then contact Samsung Customer Service Centre.
‒ Continued use can result in a fire or electric shock.
• Do not leave heavy objects or items that children like (toys, sweets, etc.) on top of the product.
‒ The product or heavy objects may fall as children try to reach for the toys or sweets resulting in a
serious injury.
• During a lightning or thunderstorm, power off the product and remove the power cable.
• Do not drop objects on the product or apply impact.
• Do not move the product by pulling the power cord or any cable.
• If a gas leakage is found, do not touch the product or power plug. Also, ventilate the area
immediately.
• Do not lift or move the product by pulling the power cord or any cable.
• Do not use or keep combustible spray or an inflammable substance near the product.
• Ensure the vents are not blocked by tablecloths or curtains.
‒ An increased internal temperature may cause a fire.
• Do not insert metallic objects (chopsticks, coins, hairpins, etc) or objects that burn easily (paper,
matches, etc) into the product (via the vent or input/output ports, etc).
‒ Be sure to power off the product and disconnect the power cord when water or other foreign
substances have entered the product. Then contact Samsung Customer Service Centre.
• Do not place objects containing liquid (vases, pots, bottles, etc) or metallic objects on top of the
product.
‒ Be sure to power off the product and disconnect the power cord when water or other foreign
substances have entered the product. Then contact Samsung Customer Service Centre.
7
Caution
• Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage
burn-in or defective pixels.
‒ Set the screen to power-saving mode or moving-picture screen saver when not using the product
for an extended period of time.
• Disconnect the power cord from the power socket if you do not plan on using the product for an
extended period of time (vacation, etc).
‒ Dust accumulation combined with heat can cause a fire, electric shock or electric leakage.
• Use the product at the recommended resolution and frequency.
‒ Your eyesight may deteriorate.
• Do not put AC/DC adapters together.
• Remove the plastic bag from the AC/DC adapter before you use it.
• Do not let water enter the AC/DC adapter device or get the device wet.
‒ An electric shock or fire may result.
‒ Avoid using the product outdoors where it can be exposed to rain or snow.
‒ Be careful not to get the AC/DC adapter wet when you wash the floor.
• Do not put the AC/DC adapter near to any heating apparatus.
‒ Otherwise, a fire may result.
• Keep the AC/DC adapter in a well-ventilated area.
• If you place the AC/DC power adapter hanging with the cord input facing upwards, water or other
foreign substances could enter the Adapter and cause the Adapter to malfunction.
Make sure to rest the AC/DC power adapter flat on a table or the floor.
• Do not hold the product upside-down or move it by holding the stand.
‒ The product may fall and become damaged or cause an injury.
• Looking at the screen too close for an extended period of time can deteriorate your eyesight.
• Do not use humidifiers or stoves around the product.
• Rest your eyes for more than 5 minutes or look at distance objects for every 1 hour of product use.
• Do not touch the screen when the product has been turned on for an extended period of time as it
will become hot.
• Store small accessories out of the reach of children.
• Exercise caution when adjusting the product angle.
‒ Your hand or finger may get stuck and injured.
‒ Tilting the product at an excessive angle may cause the product to fall and an injury may result.
• Do not place heavy objects on the product.
‒ Product failure or personal injury may result.
• When using headphones or earphones, do not turn the volume too high.
‒ Having the sound too loud may damage your hearing.
8
Chapter 02
Preparations
Parts
Control Panel
―
The colour and shape of parts may differ from what is shown. Specifications are subject to change without
notice to improve quality.
JOG Button
UP
LEFTRIGHT
PRESS(ENTER)
DOWN
Function Key Guide
PartsDescription
Multi directional button that helps navigate.
JOG Button
Power LED
Function Key Guide
―
The JOG button is located on the rear left side of the product. The button can be
used to move up, down, left or right, or as Enter.
This LED is power status indicator and works as
• Power On (Power button): Power LED Off
• Power saving mode: Power LED Blinking
• Power Off (Power button): Power LED On
―
The Power LED operation can be swapped by changing in the menu. (System →
Power LED On) Actual models because of functional variation maybe haven’t this
function.
―
power button is located on the left of the rear and used to turn on or off
The
the product.
Press the JOG button when the screen is turned on. The Function Key Guide
will appear. To access the onscreen menu when the guide is displayed, press
the corresponding direction button again.
―
Function Key Guide may vary depending on the function or product model. Please
refer to the actual product.
Power LED
Return
9
Function Key Guide
―
To use the Function Key Guide, press the JOG button. Then the following window appears.
UP/DOWN/LEFT/RIGHT: Move to the item you want. The
description for each item will appear when the focus changes.
PRESS(ENTER): The selected item will be applied.
Return
PartsDescription
Menu
Source
Eye Saver Mode
Power Off
Selects by moving the JOG button in the Function Key Guide screen.
This product shows the menu as an on-screen display.
Selects to change the input source by moving the JOG button in the
Function Key Guide screen. A message will appear on the top left corner
of the screen if the input source has been changed.
Selects by moving the JOG button in the Function Key Guide screen.
Press to enable or disable Eye Saver Mode.
The items below are not available if the Eye Saver Mode function is
enable.
• Game → Picture Mode, Black Equalizer
• Picture → Picture Mode, Brightness, Color
• System → Smart ECO Saving+
Selects to turn the product off by moving the JOG button in the
Function Key Guide screen.
Return
―
Actual models because of functional variation, Function Key Guide options will be different.
Return to the previous menu by using the JOG button to select the
icon when the Function Key Guide Screen is displayed.
10
When the product displays nothing (i.e. Power saving mode or Non-signal mode), 2 direct keys for control
source and power could be used as below.
JOG ButtonPower saving/Non-signal mode
UPSource Change
DOWN
PRESS(ENTER) for 2 secondsPower Off
When the product displays the menu the JOG Button could be used as below.
JOG ButtonAction
UP/DOWNMove the option
Exit the menu.
LEFT
RIGHT
PRESS(ENTER)Save the value and close Sublist.
Close Sublist without saving value.
Value decreases in the slider.
Move to sublist.
Value increases in the slider.
11
Changing Brightness, Contrast and Sharpness settings
Changing the Volume setting
You can adjust Brightness, Contrast or Sharpness by moving the JOG button up or down, if no OSD menu
is displayed.
Sharpness
Brightness
Contrast
―
The displayed image may differ depending on the model.
Brightness
―
This menu is not available when Eye Saver Mode is enabled.
―
This menu is not available when Picture Mode is set to Dynamic Contrast mode.
Contrast
―
This menu is not available when Picture Mode is set to Cinema or Dynamic Contrast mode.
Sharpness
―
This menu is not available when Picture Mode is set to Cinema or Dynamic Contrast mode.
100
You can adjust Volume by moving the JOG button left or right, if no OSD menu is displayed.
Volume
―
The displayed image may differ depending on the model.
―
If the audio quality of a connected input device is poor, the Auto Mute function on the product may mute the
sound or cause choppy audio when applying the headphones or speakers. Set the input volume for the input
device to at least 20% and control the volume using the volume control (JOG button LEFT/RIGHT) on the
product.
―
What is Auto Mute?
The function mutes the audio to improve sound effect when there is sound noise or when the input source
is weak, usually due to a problem with the volume of an input device.
―
To activate the Mute function, access the Volume control screen, then use the JOG button to move the focus
down.
To deactivate the Mute function, access the Volume control screen, then increase or decrease the Volume.
50
Mute
12
Types of Ports
HDMI IN 1
HDMI IN 2
DP IN
Adjusting the Product Tilt
―
The functions available may vary depending on the product model. The colour and shape of parts may differ
from what is shown. Specifications are subject to change without notice to improve quality. Refer to the
actual product.
HDMI IN 2DP IN
DC 14V
HDMI IN 1
HDMI IN 1HDMI IN 2DP IN
DC 14V
PortDescription
Connects to a source device using an HDMI cable or HDMI-DVI cable.
Connects to a PC using a DP cable.
Connect to an audio output device such as headphones.
―
The sound could only be heard when using the HDMI to HDMI cable or DP cable.
―
The colour and shape of parts may differ from what is shown. Specifications are subject to change without
notice to improve quality.
-2.0° (±2.0°) ~ 20.0° (±2.0°)
• The product tilt can be adjusted.
• Hold the lower part of the product and adjust the tilt carefully.
DC 14V
Connects to the AC/DC adapter.
13
Loading...
+ 29 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.