Samsung LA32R71W 07 Alignment & Adjustment
3 Alignments and Adjustments
3-1
3 Alignments and Adjustments
3-1 Ser vice Instr uction
1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation.
Check the basic characteristics such as height, horizontal and vertical sync.
2. Use the specified test equipment or its equivalent.
3. Correct impedance matching is essential.
4. Avoid overload. Excessive signal from a sweep generator might overload the front-end
of the TV. When inserting signal markers, do not allow the marker generator to distort
test result.
5. Connect the TV only to an AC power source with voltage and frequency as specified on
the backcover nameplate.
6. Do not attempt to connect or disconnect any wire while the TV is turned on. Make sure
that the power cord is disconnected before replacing any parts.
7. To protect aganist shock hazard, use an isolation transform.
3 Alignments and Adjustments
3-2
3-2 How to Access Service Mode
3-2-1 Entering Factory Mode
" "
- If you have Factory remote - control
- The buttons are active in the service mode.
1. Remote - Control Key : Power, Arrow Up, Arrow Down, Arrow Left
Arrow Right, Menu, Enter, Number Key(0~9)
2. Function - Control Key : Power, CH +, CH -, VOL +, VOL -,
Menu, TV/VIDEO(Enter)
3-2-2 Panel Check
Specially for LA26,32R7**, You have to check Panel Maker Because of different adjustments as follows.
First of all, Check the label rating!
1) Label Rating File
If Panel Mark is "A", Set the factory mode
indicating as follows.
Panel BOM(Bill of material) : BN07-00289A
Connector between Panel and Power Unit
: BN39-00603A (250mm)
* Option Byte
1. Gamma "AUO"
2. Panel Option "AUO_AMVA"
If Panel Mark is "S" or not printed.
Set the factory mode indicating as follows.
Panel BOM(Bill of material) : BN07-00247A
Connector between Panel and Power Unit
: BN39-00603M (300mm)
* Option Byte
1. Gamma "OFF"
2. Panel Option "AMLCD_INT"
Others are same shown below.
Panel check
3 Alignments and Adjustments
3-3
3-3 Factory Data
1. Calibration
2. Option Table XXXX XXXX
3. White Balance
4. SVP-PX
5. Option Block
6. STV8257/STA323W
7. YC Delay
8. Adjust
9. I2C Check
10. W/B MOVIE
11. Checksum
12. Reset
13. Spread Spectrum
T-BRDMPEA-0161 (Main Micom Ver)
T-BRDMPEUS-1000 (Sub Micom Ver)
Month / Day / Year / Hour / Min. / Sec.
1. Calibration
1) AV Calibration
2) COMP Calibration
3) PC Calibration
4) HDMI Calibration
2. Option Table XXXX XXXX
Inch Option 32" Carrier Mute ON TTX Group Auto
Gamma OFF Language English Auto Power ON
Panel Option AMLCD_INT Auto FM ON Magazine LNA OFF
2HDMI OFF High Deviation OFF ---- G
Brt.Sensor OFF TTX ON ---- OFF
EnergySave ON TTX List Flof Debug OFF
LBE/FBE OFF ACR OFF Ch.Table SUWON
FRC(Micronas) OFF Dynamic CE ON iDTV_Cntry UK
FRC(Samsung) OFF Dynamic Dimming ON Dynamic Contrast OFF
LNA OFF Tuner TOP 8
3 Alignments and Adjustments
3-4
1. Calibration
2. Option Table
AV Calibration EXE
COMP Calibration EXE
PC Calibration EXE
HDMI Calibration EXE
Inch Option 23"/32"/37"/40"/46"/57"
Gamma OFF/AUO/CMO/AMLCD
Panel Option
AUO / CMO/AMLCD_INT/Panel3 / Panel4 / Panel5 / Panel6
2Hdmi OFF
Brt. Sensor FF
EnergySave ON
LBE/FBE OFF
FRC(Micronas) OFF
FRC2X OFF
LNA OFF
Carrier Mute ON
Language English
Auto FM ON
High Deviation OFF
TTX ON
TTX List Flof
ACR OFF
Dynamic CE ON
Dynamic Dimming ON
Tuner TOP 8
TTX Group Auto
Auto Power ON
Magazine LNA OFF
Debug OFF
Ch. Table SUWON
iDTV_Cntry UK
Dynamic Contrast OFF
BORDEAUX INCH OPTION
Panel Maker Gamma Panel Option
26 AUO AUO AUO
32 AUO AUO AUO
32 AMLCD OFF AMLCD_INT
37 AUO AUO AUO
40 AMLCD AMLCD AMLCD_INT
Loading...