Samsung K4D263238E-GC40, K4D263238E-GC36, K4D263238E-GC33, K4D263238E-GC2A, K4D263238E-GC25 Datasheet

...
K4D263238E-GC
128Mbit GDDR SDRAM
with Bi-directional Data Strobe and DLL
128M GDDR SDRAM
1M x 32Bit x 4 Banks
Synchronous DRAM
(144-Ball FBGA)
Revision 1.7
November 2003
Samsung Electronics reserves the right to change products or specification without notice.
- 1 -
Rev 1.7 (Nov. 2003)
K4D263238E-GC
Revision History
Revision 1.7 (November 14, 2003)
• Typo corrected
Revision 1.6 (August 14, 2003)
• Added a note for the input reference voltage of clock in case of differential clocks
Revision 1.5 (August 11, 2003)
• Typo corrected
Revision 1.4 (April 30, 2003)
• Added Lead free package part number in the datasheet
Revision 1.3 (April 14, 2003)
• K4D263238E-GC2A/33/36 support wide voltage range from 2.375V to 2.94V
Revision 1.2 (April 7, 2003)
• Removed K4D263238E-GL36 from the spec.
Revision 1.1 (March 17, 2003)
• Typo corrected
128M GDDR SDRAM
Revision 1.0 (February 13, 2003)
• Defined DC spec
• Added K4D263238E-GC25 and K4D263238E-GL36 in the spec.
- 2 -
Rev 1.7 (Nov. 2003)
K4D263238E-GC
128M GDDR SDRAM
1M x 32Bit x 4 Banks Graphic Double Data Rate Synchronous DRAM with Bi-directional Data Strobe and DLL
FEATURES
• VDD/VDDQ = 2.8V ± 5% for -GC25
• VDD/VDDQ = 2.5V ± 5% for -GC2A/33/36/40/45
• SSTL_2 compatible inputs/outputs
• 4 banks operation
• MRS cycle with address key programs
-. Read latency 3, 4, 5 (clock)
-. Burst length (2, 4, 8 and Full page)
-. Burst type (sequential & interleave)
• Full page burst length for sequential burst type only
• Start address of the full page burst should be even
• All inputs except data & DM are sampled at the positive going edge of the system clock
• Differential clock input
• No Wrtie-Interrupted by Read Function
• 4 DQS’s ( 1DQS / Byte )
• Data I/O transactions on both edges of Data strobe
• DLL aligns DQ and DQS transitions with Clock transition
• Edge aligned data & data strobe output
• Center aligned data & data strobe input
• DM for write masking only
• Auto & Self refresh
• 32ms refresh period (4K cycle)
• 144-Ball FBGA
• Maximum clock frequency up to 400MHz
• Maximum data rate up to 800Mbps/pin
ORDERING INFORMATION
Part NO. Max Freq. Max Data Rate Interface Package
K4D263238E-GC25 400MHz 800Mbps/pin K4D263238E-GC2A 350MHz 700Mbps/pin
K4D263238E-GC33 300MHz 600Mbps/pin K4D263238E-GC36 275MHz 550Mbps/pin K4D263238E-GC40 250MHz 500Mbps/pin K4D263238E-GC45 222MHz 444Mbps/pin
SSTL_2
(VDD/VDDQ=2.8V)
SSTL_2
(VDD/VDDQ=2.5V)
144-Ball FBGA
K4D263238E-VC is the Lead Free package part number.
GENERAL DESCRIPTION
FOR 1M x 32Bit x 4 Bank DDR SDRAM
The K4D263238E is 134,217,728 bits of hyper synchronous data rate Dynamic RAM organized as 4 x1,048,576 words by 32 bits, fabricated with SAMSUNGs high performance CMOS technology. Synchronous features with Data Strobe allow extremely high performance up to 3.2GB/s/chip. I/O transactions are possible on both edges of the clock cycle. Range of operating frequencies, programmable burst length and pro grammable latencies allow the d evice to be useful for a variety of high performance memory system applications.
- 3 -
Rev 1.7 (Nov. 2003)
K4D263238E-GC
PIN CONFIGURATION (Top View)
2345678910111213
DQS0
B
DM0
VSSQ
DQ3
DQ2
DQ0
DQ31
DQ29
128M GDDR SDRAM
DQ28
VSSQ
DM3
DQS3
DQ4
C
DQ6
D
DQ7
E
DQ17
F
DQ19
G
DQS2
H
DQ21
J
DQ22
K
CAS
L
RAS
M
N
CS
VDDQ
DQ5
VDDQ
DQ16
DQ18
DM2
DQ20
DQ23
WE
NC
NC
VSSQ VSSQ VSSQ
VDD
VDDQ
VDDQ
VDDQ
VDDQ
VDD
NOTE:
1. RFU1 is reserved for A12
2. RFU2 is reserved for BA2
3. VSS Thermal balls are optional
NC
NC
NC
BA0
A2
A1
VDDQ
VDD
VSS
Thermal
VSS
Thermal
VSS
Thermal
VSS
Thermal
VDD VDD
A11
A3
VDDQ
VSS VSS VSS VSS
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSS
BA1
A0
DQ1
VSSQ
VSS
Thermal
VSS
Thermal
VSS
Thermal
VSS
Thermal
A10
VDDQ
VDD
VSS
Thermal
VSS
Thermal
VSS
Thermal
VSS
Thermal
A9
A4
DQ30
VSSQ
VSSQ
VSS
Thermal
VSS
Thermal
VSS
Thermal
VSS
Thermal
VSSVSSVSSVSS
RFU
1
A6
VDDQ NC
VSSQ VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSS
RFU
A7
VDDQ
DQ26
VDD
VDDQ
VDDQ
NC
VDDQ
VDDQ
VDD
CK
2A5
A8/AP
VDDQ
DQ15
DQ13
DM1
DQ11
DQ9
NC
CK
CKE
DQ27
DQ25
DQ24
DQ14
DQ12
DQS1
DQ10
DQ8
NC
MCL
VREF
PIN DESCRIPTION
CK,CK Differential Clock Input BA0, BA1 Bank Select Address CKE Clock Enable A0 ~A11 Address Input CS Chip Select DQ0 ~ DQ31 Data Input/Output RAS CAS WE Write Enable VDDQ Power for DQs DQS Data Strobe VSSQ Ground for DQs DM Data Mask NC No Connection RFU Reserved for Future Use MCL Must Connect Low
Row Address Strobe VDD Power Column Address Strobe VSS Ground
- 4 -
Rev 1.7 (Nov. 2003)
K4D263238E-GC
128M GDDR SDRAM
INPUT/OUTPUT FUNCTIONAL DESCRIPTION
Symbol Type Function
The differential system clock Input.
CK, CK*1 Input
CKE Input
CS Input
RAS
CAS Input
WE Input
DQS0 ~ DQS3 Input/Output
DM0 ~ DM3 Input
DQ0 ~ DQ31 Input/Output Data inputs/Outputs are multiplexed on the same pins.
BA0, BA1 Input Selects which bank is to be active.
A0 ~ A11 Input
V
DD/VSS Power Supply Power and ground for the input buffers and core logic.
VDDQ/VSSQ Power Supply
VREF Power Supply Reference voltage for inputs, used for SSTL interface.
NC/RFU No connection/
MCL Must Connect Low Must connect low
*1 : The timing reference point for the differential clocking is the cross point of CK and CK. For any applications using the single ended clocking, apply V
Input
Reserved for future use
All of the inputs are sampled on the rising edge of the clock except DQs and DMs that are sampled on both edges of the DQS.
Activates the CK signal when high and deactivates the CK signal when low. By deactivating the clock, CKE low indicates the Power down mode or Self refresh mode.
CS enables the command decoder when low an d di sa bl e d th e com­mand decoder when high. When the command decoder is disabled, new commands are ignored but previous operations continue.
Latches row addresses on the positive going edge of the CK with RAS
low. Enables row access & precharge.
Latches column addresses on the positive going edge of the CK with CAS low. Enables column access.
Enables write operation and row precharge. Latches data in starting from CAS, WE active.
Data input and output are synchronized with both edge of DQS. DQS0 for DQ0 ~ DQ7, DQS1 for DQ8 ~ DQ15, DQS2 for DQ16 ~ DQ23, DQS3 for DQ24 ~ DQ31.
Data In mask. Data In is masked by DM Latency=0 when DM is high in burst write. DM0 for DQ0 ~ DQ7, DM1 for DQ8 ~ DQ15, DM2 for DQ16 ~ DQ23, DM3 for DQ24 ~ DQ31.
Row/Column addresses are multiplexed on the same pins. Row addresses : RA0 ~ RA11, Column addresses : CA0 ~ CA7. Column address CA
Isolated power supply and ground for the output buffers to provide improved noise immunity.
This pin is recommended to be left "No connection" on the device
REF to CK pin.
8 is used for auto precharge.
- 5 -
Rev 1.7 (Nov. 2003)
K4D263238E-GC
BLOCK DIAGRAM (1Mbit x 32I/O x 4 Bank)
128M GDDR SDRAM
32
Intput Buffer
LWE
CK,CK
ADDR
LCKE
Address Register
Bank Select
LRAS
Refresh Counter
Row Buffer
LCBR
LRAS
LCBR
LWE
CK, CK
Row Decoder
Col. Buffer
LCAS
Data Input Register
Serial to parallel
64
1Mx32
1Mx32
1Mx32
1Mx32
Column Decoder
Latency & Burst Length
Programming Register
LWCBR
Sense AMP
2-bit prefetch
64 32
DLL
CK,CK
LDMi
Output BufferI/O Control
x32
DQi
Strobe
Gen.
LDMi
Data Strobe
(DQS0~DQS3)
CK,CK
Timing Register
CKE CS RAS CAS WE DMi
- 6 -
Rev 1.7 (Nov. 2003)
Loading...
+ 11 hidden pages