SAMSUNG HW-R470 User Manual [nl]

FULL MANUAL
HW-R470
Imagine the possibilities
Thank you fo r purchasing this Samsung product.
To receive more complete s ervice, please register
your product at www.samsung.com/register
SAFETY INFORMATION
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Refer to the table below for an explanation of symbols which may be on your Samsung product.
CAUTION
RISK OF E LECTRIC S HOCK.
DO NOT OP EN.
This symbol indicates that high voltage is present inside. It is dangerous to make any kind of contact with any internal part of this product.
This symbol indicates that this product has included important literature concerning operation and maintenance.
Class II product : This symbol indicates that it does not require a safety connection to electrical ear th (ground).
If this symbol is not present on a product with a power cord, the produc t MUST have a reliable connection to protective ear th (ground).
WARNING
• To reduce the risk of re or electric shock, do not expose this appliance to rain or moisture.
CAUTION
• TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
• This apparatus shall always be connected to a AC outlet with a protective grounding connection.
• To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.
• Do not expose this apparatus to dripping or
splashing. Do not put objects lled with
liquids, such as vases on the apparatus.
• To turn this apparatus off completely, you must pull the power plug out of the wall socket. Consequently, the power plug must be easily and readily accessible at all times.
AC voltage : This symbol indicates that the rated voltage marked with the symbol is AC voltage.
DC voltage : This symbol indicates that the rated voltage marked with the symbol is DC voltage.
Caution, Consult instructions for use : This symbol instructs the user to consult the user manual for further safety related information.
ENG - ii
PRECAUTIONS
1. Ensure that the AC power supply in your
house complies with the power
requirements listed on the identication
sticker located on the bottom of your product. Install your product horizontally, on a suitable base (furniture), with enough space around it for ventilation (7~10 cm). Make sure the ventilation slots are not
covered. Do not place the unit on ampliers
or other equipment which may become hot. This unit is designed for continuous use. To fully turn off the unit, disconnect the AC plug from the wall outlet. Unplug the unit if you intend to leave it unused for a long period of time.
2. During thunderstorms, disconnect the AC plug from the wall outlet. Voltage peaks due to lightning could damage the unit.
3. Do not expose the unit to direct sunlight or other heat sources. This could lead to overheating and cause the unit to malfunction.
4. Protect the product from moisture (i.e.
vases), and excess heat (e.g. a replace) or
equipment creating strong magnetic or
electric elds. Unplug the power cable from
the AC wall socket if the unit malfunctions. Your product is not intended for industrial use. It is for personal use only. Condensation may occur if your product has been stored in cold temperatures. If transporting the unit during the winter, wait approximately 2 hours until the unit has reached room temperature before using.
5. The battery used with this product contains chemicals that are harmful to the environment. Do not dispose of the battery in the general household trash. Do not expose the battery to excess heat, direct
sunlight, or re. Do not short circuit,
disassemble, or overheat the battery. Danger of explosion if the battery is replaced incorrectly. Replace only with the same or equivalent type.
ABOUT THIS MANUAL
The user manual has two parts: this simple paper USER MANUAL and a detailed FULL MANUAL you can download.
USER MANUAL
See this manual for safety instructions, product installation, components,
connections, and product specications.
FULL MANUAL
You can access the FULL MANUAL on Samsung’s on-line customer support centre by scanning the QR code. To see the manual on your PC or mobile device, download the manual in document format from Samsung’s website. (http://www.samsung.com/support)
Design and specications are subject to change
without prior notice.
ENG - iii
CONTENTS
01 Checking the Components 2
Inserting Batteries before using the Remote Control (AA batteries X 2) ------------------------- 3
02 Product Overview 4
Front Panel / Right Side Panel of the Soundbar ------------------------- 4
Bottom Panel of the Soundbar ------------------------- 5
03 Connecting the Soundbar 6
Connecting Electrical Power
Connecting the Soundbar to the Subwoofer
– Automatic connection between the Subwoofer and the Soundbar – Manually connecting the Subwoofer if automatic connection fails
Connecting an SWA-8500 to your Soundbar
-------------------------
-------------------------
-------------------------
-------------------------
-------------------------
04 Connecting to your TV 13
Method 1. Connecting with a Cable
– Connecting using an Optical Cable
Method 2. Connecting Wirelessly
– Connecting a TV via Bluetooth
-------------------------
-------------------------
-------------------------
-------------------------
05 Connecting an External Device 16
Connecting using an Optical or Analogue Audio (AUX) Cable
-------------------------
06 Connecting a USB Storage Device 17
6
7
7 8
10
13
13
14
14
16
ENG - iv
07 Connecting a Mobile Device 19
Connecting via Bluetooth
Using the Samsung Audio Remote App
– Installing the Samsung Audio Remote App – Launching the Samsung Audio Remote App
-------------------------
-------------------------
-------------------------
-------------------------
08 Using the Remote Control 23
How to Use the Remote Control
Adjusting the Soundbar volume with a TV remote control
Using the Hidden Buttons (Buttons with more than one function)
Output specications for the different sound effect modes
-------------------------
-------------------------
-------------------------
-------------------------
09 Installing the Wall Mount 28
Installation Precautions
Wallmount Components
Detaching the Soundbar from the Wall
-------------------------
-------------------------
-------------------------
30
10 Software Update 31
Updating Procedure
If UPDATE is not displayed
-------------------------
-------------------------
32
19
22
22 22
23
26
27
27
28
28
31
11 Troubleshooting 33
12 Licence 34
13 Open Source Licence Notice 34
14 Important Notes About Service 34
15 SpecicationsandGuide 35
Specications
-------------------------
ENG - v
35

01 CHECKING THE COMPONENTS

PAIR
SOUND MODE
VOL WOOFER
SOUNDBAR
Soundbar Main Unit Subwoofer Remote Control /
1 3
Power Cord (Subwoofer) AC/DC Adapter
(Main Unit)
2
Connect the AC plug to the adapter until you hear a “snapping” sound to ensure they are securely fastened.
AC Plug
(Depending on the country and
model)
x 2
x 2
Do not detach the AC plug from the adapter (it will not be removed once it has been attached).
Holder-Screw Screw Bracket-Wall Mount L Bracket-Wall Mount R
Wireless Surround Speaker SET (SWA-8500)
STANDBY
LINK
x 2
Optic al Cable
Batteries
Wall Mount Guide
Surround Speaker Power Cord
x 2
Wirele ss Receiver Modul e Speaker Cable
• For more information about the power supply and power consumption, refer to the label attached to the product. (Label: Bottom of the Soundbar Main Unit)
• The appearance of the accessories may differ slightly from the illustrations above.
• The power components are labelled (1, 2, 3). For more information about power connections, see page 6.
ENG - 2
• To purchase additional components or optional cables, contact a Samsung Service Centre or Samsung Customer Care.
• Depending on the region, the AC plug may vary in appearance, or it may be supplied integrated with the AC/DC adapter.

Inserting Batteries before using the Remote Control (AA batteries X 2)

Slide the battery cover in the direction of the arrow until it is completely removed. Insert 2 AA batteries (1.5V) oriented so that their polarity is correct. Slide the battery cover back into position.
ENG - 3

02 PRODUCT OVERVIEW

Front Panel / Right Side Panel of the Soundbar

Position the product so that the SAMSUNG logo is located on the top.
󱂓
Display
󱂓
Displays the product’s status and current mode.
+/- (Volume) But ton
Adjusts the volume.
󱂔
• When adjusted, the volume level appears on the Soundbar ’s front display.
󱂕
(Power) Button
Turns the power on and off.
(Source) But ton
Selects the source input mode.
󱂔
Right Sid e of the Soundbar
󱂕 󱂖
Input mode Display
Optical Digital input D.IN
󱂖
• To turn on “BT PAIRING” mode, change the source to “ BT” mode, and then press and hold the
• When you plug in the AC cord, the power button will begin working in 4 to 6 seconds.
• When you turn on this unit, there will be a 4 to 5 second delay before it produces sound.
• If you want to enjoy sound only from the Soundbar, you must turn off the TV’s speakers in the Audio Setup menu of your TV. Refer to the owner’s manual supplied with your TV.
AUX input AUX
BLUETOOTH mode BT
USB mode USB
(Source) button for more than 5 seconds.
ENG - 4

Bottom Panel of the Soundbar

󱂓
󱂔
󱂕
DIGITAL AUD IO IN (OPTIC AL)
󱂓
Connect to the digital (optical) output of an ex ternal device.
USB (5V 0. 5A)
󱂔
Connect a USB device here to play music les on the USB device through the Soundbar.
AUX IN
󱂕
Connect to the Analogue output of an external device.
DC 19V (Powe r Supply In)
󱂖
Connect the AC/DC power adapter.
DIGITAL AUDIO IN (OPTICAL)
USB (5V 0.5A)
AUX IN
DIGITAL AUDIO IN (OPTICAL)
USB (5V 0.5A)
AUX IN
DC 19V
DC 19V
󱂖
• When disconnecting the power cord from a wall outlet, pull the plug. Do not pull the cable.
• Do not connect this unit or other components to an AC outlet until all connections between components are complete.
ENG - 5

03 CONNECTING THE SOUNDBAR

Connecting Electrical Power

Use the power components (1, 2 the following order:
, 3
) to connect the Subwoofer and Soundbar to an electrical outlet in
1 Connect the power cord to the Subwoofer. 2 Connect the AC plug to the adapter.
3
Connect the power adapter to the Soundbar and then to a wall socket.
See the illustrations below.
• For more information about the required electrical power and power consumption, refer to the label attached to the product. (Label: Bottom of the Soundbar Main Unit)
2 AC Plug 3 AC/DC Adapter
POWER
Rear of Subwoofer
1 Power Cord
Connecting
Electric al Power
DC 19V
DC 19V
Bott om of the
Soundbar Main Unit
DC 19V (Power Jack)
• Make sure to rest the AC/DC Adapter at on a table or the oor. If you place the AC/DC Adapter so that it is hanging with the AC cord input facing upwards, water or other foreign substances could enter the Adapter and cause the Adapter to malfunction.
ENG - 6

Connecting the Soundbar to the Subwoofer

When the subwoofer is connected, you can enjoy rich bass sound.
Automatic connection between the Subwoofer and the Soundbar
When you turn the power on after connecting the power cables to the Soundbar and subwoofer, the subwoofer is automatically connected to the Soundbar.
• When auto pairing is complete, the blue indicators at the rear of the subwoofer turn on.
LED Indicator Lights on the Rear of Subwoofer
LED Status Description Resolution
Successfully connected (normal operation)
Standby (with the Soundbar main unit turned off)
Connection failed
-
Check if the power cable attached to the main Soundbar unit is connected properly or wait about 5 minutes. If blinking persists, try manually connecting the subwoofer. See page 8.
Check if the power cable attached to the main Soundbar unit is connected properly.
Connect again. See the instructions for manual connection on page 8.
See the contact information for the Samsung Service Centre in this manual.
Blue
Red On
Red and
blue
On
Blinking Recovering the connection
Blinking Malfunction
ENG - 7
Manually connecting the Subwoofer if automatic connection fails
Before per forming the manual connection procedure below:
• Check whether the power cables for the Soundbar and subwoofer are connected properly.
• Make sure that the Soundbar is turned on.
1. Press and hold ID SET on the rear of the subwoofer for at least 5 seconds.
• The red indicator on the rear of the subwoofer turns off and the blue indicator blinks.
5 Sec
Rear of Subwoofer
2. Press and hold the Up button on the remote control for at least 5 seconds.
• The ID SET message appears on the display of the Soundbar for a moment, and then it disappears.
• The Soundbar will automatically power on when ID SET is complete.
PAIR
5 Sec
3. Check if the LINK LED is solid blue (connection complete).
The LINK LED indicator stops blinking and glows a solid blue when a connection is established between the Soundbar and the Wireless Subwoofer.
Blue is On
ENG - 8
ID SET
NOTES
• Do not connect the power cord of this product or your TV to a wall outlet until all connections between components are complete.
• Before moving or installing this product, be sure to turn off the power and disconnect the power cord.
• If the main unit is powered off, the wireless subwoofer will go into stand-by mode and the STANDBY LED on the rear will turn red after blinking in blue several times.
• If you use a device that uses the same frequency (5.8GHz) as the Soundbar near the Soundbar, interference may cause some sound interruption.
• The maximum transmission distance of the main unit’s wireless signal is about 10 meters, but may vary depending on your operating environment. If a steel-concrete or metallic wall is between the main unit and the wireless subwoofer, the system may not operate at all because the wireless signal cannot penetrate metal.
PRECAUTIONS
• Wireless receiving antennas are built into the wireless subwoofer. Keep the unit away from water and moisture.
• For optimal listening performance, make sure that the area around the wireless subwoofer and the Wireless Receiver Module is clear of any obstructions.
ENG - 9

Connecting an SWA-8500 to your Soundbar

L
R
Expand to true wireless surround sound by connecting the Samsung Wireless Surround Speaker SET (SWA-8500) to your Soundbar.
1. Connect the Wireless Receiver Module to 2 Surround Speakers
Use the speaker cables to connect the two surround sound speakers to the Wireless Receiver Module.
• The speaker cables are colour coded.
L
R
SURROUND SPEAKERS OUT SPEAKER IMPEDANCE : 3Ω
SURROUND-LEFT SURROUND-RIGHT
ID SET
SURROUND-LEFT
POWER
SURROUND-RIGHT
When connecting the speaker cables to the Wireless Receiver Module, follow these steps:
1. Insert the grey plug into the grey jack on the Wireless Receiver.
2. Insert the blue plug into the blue jack on the Wireless Receiver.
When connecting the speaker cables to the surround speakers, follow these steps:
1. Match the speaker cable connected to the grey jack to the speaker with the grey label.
2. Match the speaker cable connected to the blue jack to the speaker with the blue label.
3. Insert the red and black coloured ends of each speaker cable into the red and black jacks of the
appropriate speakers.
• The labels are on the backs of the speakers.
ENG - 10
2. Check the standby status after plugging into an electrical outlet
POWER
ID SET
LINK
The LINK LED indicator (blue LED) on the Wireless Receiver Module blinks. If the LED does not blink, press the ID SET button on the back of the Wireless Receiver Module with a pen tip for 5~6 seconds until the LINK LED indicator blinks (in Blue).
L
SURROUND SPEAKERS OUT SPEAKER IMPEDANCE : 3Ω
R
ID SET
POWER
5 Sec
STANDBY
LINK
Blue blinking
3.Congure“IDSET”usingtheSoundbar’sremotecontrol
Press and hold the Up button on the remote control for at least 5 seconds.
• The ID SET message appears on the display of the Soundbar for a moment, and then it disappears.
• The Soundbar will automatically power on when ID SET is complete.
PAIR
5 Sec
ID SET
CAUTION
• If your Soundbar was playing music when it connects to the SWA-8500, you may hear some
stuttering from the woofer as the connection nalises.
ENG - 11
4. Check if the LINK LED is solid blue (connection complete)
LINK
ID SET
The LINK LED indicator stops blinking and
STANDBY
LINK
glows a solid blue when a connection is established between the Soundbar and the Wireless Receiver Module.
Blue is On
5. If the SWA-8500 does not connect, take the necessary steps according to the
LEDIndicator’sstatus
LED status Action
On Connected with the Soundbar -
LINK (Blue)
STANDBY (Red)
Blinking Connection standby status
On Connection failure
Check if the Soundbar is turned on
Repeat steps 3 through 4.
Check if the Soundbar is turned on
1. Press the ID SET button on the back of the Wireless Receiver Module with a pen tip for 5~6 seconds until the LINK LED indicator blinks (in Blue).
L
SURROUND SPEAKERS OUT SPEAKER IMPEDANCE : 3Ω
R
ID SET
5 Sec
2. Repeat steps 3 through 4.
Others - Errors Contact a Samsung Service Centre.
ENG - 12

04 CONNECTING TO YOUR TV

Hear TV sound from your Soundbar through wired or wireless connections.
• When the Soundbar is connected to selected Samsung TVs, the Soundbar can be controlled using the TV’s remote control.
– This feature is supported by 2017 and later Samsung Smart TVs that support Bluetooth when
you connect the Soundbar to the TV using an optical cable.
This function also allows you to use the TV menu to adjust the sound eld and various settings
as well as the volume and mute.

Method 1. Connecting with a Cable

When the audio in a broadcast is encoded in Dolby Digital and the “Digital Output Audio Format ” on your TV is set to PCM, we recommend that you change the setting to Dolby Digital. When the setting on the TV is changed, you will experience better sound quality. (The TV menu may use different words for Dolby Digital and PCM depending on the TV manufacturer.)
Connecting using an Optical Cable
Bott om of the Soundba r
DIGITAL AUDIO IN (OPTICAL)
USB (5V 0.5A)
OPTICAL OUT
󱂓
Optic al Cable
󱂔
D.IN
1. Connect the DIGITAL AUDIO IN (OPTICAL) jack on the Soundbar to the OPTICAL OUT jack of the TV
with a digital optical cable.
2. Press the (Source) button on the right side panel or remote control, and then select the “D.IN mode.
ENG - 13
Right Sid e of the Soundbar
Auto Power Link
Auto Power Link automatically turns on the Soundbar when the TV is turned on.
1. Connect the Soundbar and a TV with a digital optical cable.
2. Press the Left button on the remote control for 5 seconds to turn Auto Power
Link on or off.
• Auto Power Link is set to ON by default. (To turn off this function, hold the Left button on the remote for 5 seconds.)
• Depending on the connected device, Auto Power Link may not function.
• This function is only available in the “D.IN” mode.

Method 2. Connecting Wirelessly

Connecting a TV via Bluetooth
When a TV is connected using Bluetooth, you can hear stereo sound without the hassle of cabling.
• Only one TV can be connected at a time.
PAIR
OR
The initial connection
1. Press the PAIR button on the remote control to enter the “BT PAIRING” mode.
(OR)
a. Press the (Source) button on the right side panel and then select “BT”.
BT” changes to “BT READY” in a few seconds automatically if there is no Bluetooth device connected to the Soundbar.
b. When “BT READY” appears, press and hold the (Source) button on the right side panel
of the Soundbar for more than 5 seconds to display “BT PAIRING”.
2. Select Bluetooth mode on the TV. (For more information, see the TV’s manual.)
3. Select “[AV] Samsung Soundbar R4-Series” from the list on TV’s screen.
An available Soundbar is indicated with “Need Pairing” or “Paired” on the TV’s Bluetooth device list. To connect the TV to the Soundbar, select the message, and then establish a connection.
• When the TV is connected, [TV Name] → “BT” appears on the Soundbar’s front display.
4. You can now hear TV sound from the Soundbar.
ENG - 14
If the device fails to connect
• If a previously connected Soundbar listing (e.g. “[ AV] Samsung Soundbar R4-Series”) appears in the list, delete it.
• Then repeat steps 1 through 3.
NOTE
• After you have connected the Soundbar to your TV the rst time, use the “BT READY” mode to reconnect.
Disconnecting the Soundbar from the TV
Press the (Source) button on the right side panel or on the remote control and switch to any mode but “BT”.
• Disconnecting takes time because the TV must receive a response from the Soundbar. (The time required may differ, depending on the TV model.)
• To cancel the automatic Bluetooth connection between the Soundbar and TV, press the p (Play/Pause) button on the remote control for 5 seconds with the Soundbar in “BT READY” status.
(Toggle On → Off)
What is the difference between BT READY and BT PAIRING?
BT READY : In this mode, you can search for previously connected TVs or connect a previously connected mobile device to the Soundbar.
BT PAIRING : In this mode, you can connect a new device to the Soundbar. (Press the PAIR button on the remote control or press and hold the (Source) button on the right side of the Soundbar for more than 5 seconds while the Soundbar is in “BT” mode.)
NOTES
• If asked for a PIN code when connecting a Bluetooth device, enter <0000>.
• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the Soundbar and the Bluetooth device exceeds 10 meters.
• The Soundbar automatically turns off after 20 minutes in the Ready state.
• The Soundbar may not perform Bluetooth search or connection correctly under the following circumstances:
If there is a strong electrical eld around the Soundbar. – If several Bluetooth devices are simultaneously paired with the Soundbar. – If the Bluetooth device is turned off, not in place, or malfunctions.
• Electronic devices may cause radio interference. Devices that generate electromagnetic waves must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc.
ENG - 15

05 CONNECTING AN EXTERNAL DEVICE

Connect to an external device via a wired or wireless network to play the external device’s sound through the Soundbar.

Connecting using an Optical or Analogue Audio (AUX) Cable

BD / DVD play er / Set-top box / Game cons ole
OPTICAL OUT
R L
- AUDIO -
󱂓
Optic al Cable
󱂔
Audio (AU X) Cable
(not supplied)
DIGITAL AUDIO IN (OPTICAL)
USB (5V 0.5A)
AUX IN
Bott om of the Soundba r
Right Sid e of the Soundbar
1 Optical Cable
X Connect DIGITAL AUDIO IN (OPTICAL) on the main unit to the OPTICAL OUT jack of the Source
Device using a digital optical cable.
Y Select “D.IN” mode by pressing the (Source) button on the right side panel or on the remote
control.
2 Audio (AUX) Cable
X Connect AUX IN (Audio) on the main unit to the AUDIO OUT jack of the Source Device using an
audio cable.
Y Select “AUX” mode by pressing the (Source) button on the right side panel or on the remote
control.
ENG - 16

06 CONNECTING A USB STORAGE DEVICE

You can play music les located on USB storage devices through the Soundbar.
USB por t
DIGITAL AUDIO IN (OPTICAL)
USB (5V 0.5A)
AUX IN
DC 19V
USB (5V 0.5A)
Display
USB
Micro USB t o
USB adap ter Cable
(not supplied)
1. Connect a Micro USB to USB adapter cable with a male USB 2.0 Micro USB plug (Type B) on one
end and a standard female 2.0 USB jack (Type A) on the other end to the micro USB jack on your Soundbar.
• The Micro USB to USB adapter cable is sold separately. To purchase, contact a Samsung Service Centre or Samsung Customer Care.
2. Connect your USB device to the female end of the adapter cable.
3. Press the (Source) button on the right side panel or on the remote control, and then select USB”.
4. USB” appears in the display screen.
5. Play music les from the USB storage device through the Soundbar.
• The Soundbar automatically turns off (Auto Power Down) if no USB device has been connected for more than 20 minutes.
ENG - 17
File Format Type Compatibility list
Extension Codec Sampling Rate Bitrate
*.m p3 MPEG 1 Layer2 16kHz ~ 48kHz 80kbps~320kbps
MPEG 1 Layer3 16kHz ~ 48kHz 80kbps~320kbps
MPEG 2 Layer3 16kHz ~ 48kHz 80kbps~320kbps
MPEG 2.5 Layer3 16kHz ~ 48kHz 80kbps~320kbps
*.wma Wave_Format_MSAudio1 16kHz ~ 48kHz 56kbps~128kbps
Wave_Format_MSAudio2 16kHz ~ 48kHz 56kbps~128kbps
*.a ac AAC 16kHz ~ 96kHz 48kbps~320kbps
A A C-LC 16kHz ~ 96kHz
HE-AAC 24kHz ~ 96kHz
*.wav - 16kHz ~ 48kHz up to 3000kbps
*.o gg OGG 1.1.0 16kHz ~ 48kHz 50kbps~500kbps
128kbps~192kbps
5.1ch 320kbp s
48kbps~64kbps
5.1ch 160kbp s
• If there are too many folders and les stored on the USB device, it may take the Soundbar some
time to access and play les.
ENG - 18

07 CONNECTING A MOBILE DEVICE

Connecting via Bluetooth

When a mobile device is connected using Bluetooth, you can hear stereo sound without the hassle of cabling.
• You cannot connect more than one Bluetooth device at a time.
PAIR
Bluetooth device
OR
The initial connection
1. Press the PAIR button on the remote control to enter the “BT PAIRING” mode.
(OR)
a. Press the (Source) button on the right side panel and then select “BT”.
BT” changes to “BT READY” in a few seconds automatically if there is no Bluetooth device connected to the Soundbar.
b. When “BT READY” appears, press and hold the (Source) button on the right side panel
of the Soundbar for more than 5 seconds to display “BT PAIRING”.
2. On your device, select “[ AV] Samsung Soundbar R4-Series” from the list that appears.
• When the Soundbar is connected to the Bluetooth device, [Bluetooth Device Name] → “BT appears in the front display.
3. Play music les from the device connected via Bluetooth through the Soundbar.
If the device fails to connect
• If a previously connected Soundbar listing (e.g. “[ AV] Samsung Soundbar R4-Series”) appears in the list, delete it.
• Then repeat steps 1 and 2.
NOTE
• After you have connected the Soundbar to your mobile device the rst time, use the “BT READY mode to reconnect.
ENG - 19
What is the difference between BT READY and BT PAIRING?
BT READY : In this mode, you can search for previously connected TVs or connect a previously connected mobile device to the Soundbar.
BT PAIRING : In this mode, you can connect a new device to the Soundbar. (Press the PAIR button on the remote control or press and hold the (Source) button on the right side of the Soundbar for more than 5 seconds while the Soundbar is in “BT” mode.)
NOTES
• If asked for a PIN code when connecting a Bluetooth device, enter <0000>.
• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the Soundbar and the Bluetooth device exceeds 10 meters.
• The Soundbar automatically turns off after 20 minutes in the Ready state.
• The Soundbar may not perform Bluetooth search or connection correctly under the following circumstances:
If there is a strong electrical eld around the Soundbar. – If several Bluetooth devices are simultaneously paired with the Soundbar. – If the Bluetooth device is turned off, not in place, or malfunctions.
• Electronic devices may cause radio interference. Devices that generate electromagnetic waves must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc.
• The Soundbar supports SBC data (44.1kHz, 48kHz).
• Connect only to a Bluetooth device that supports the A2DP (AV) function.
• You cannot connect the Soundbar to a Bluetooth device that supports only the HF (Hands Free) function.
• Once you have paired the Soundbar to a Bluetooth device, selecting “[ AV] Samsung Soundbar R4-Series” from the device’s scanned devices list will automatically change the Soundbar to “BT” mode.
– Available only if the Soundbar is listed among the Bluetooth device’s paired devices.
(The Bluetooth device and the Soundbar must have been previously paired at least once.)
• The Soundbar will appear in the Bluetooth device’s searched devices list only when the Soundbar is displaying “BT READY”.
• The Soundbar cannot be paired to another Bluetooth device if already in Bluetooth mode and paired to a Bluetooth device.
Bluetooth Power On (SOUND MODE)
If a previously paired Bluetooth device tries to pair with the Soundbar when the Bluetooth Power On function is on and the Soundbar is turned off, the Soundbar turns on automatically.
1. Press and hold the SOUND MODE button for more than 5 seconds on the remote while the Soundbar is turned on.
2. ON-BLUETOOTH POWER ” appears on the Soundbar’s display.
ENG - 20
Disconnecting the Bluetooth device from a Soundbar
You can disconnect a Bluetooth device from the Soundbar. For instructions, see the Bluetooth device’s user manual.
• The Soundbar will be disconnected.
• When the Soundbar is disconnected from the Bluetooth device, the Soundbar will display BT DISCONNECTED” on the front display.
Disconnecting the Soundbar from the Bluetooth device
Press the (Source) button on the right side panel or on the remote control, and then change to any mode except “BT”.
• Disconnecting takes time because the Bluetooth device must receive a response from the Soundbar. (Disconnection time may differ, depending on the Bluetooth device)
• When the Soundbar is disconnected from the Bluetooth device, the Soundbar will display BT DISCONNECTED” on the front display.
NOTES
• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the Soundbar and the Bluetooth device exceeds 10 meters.
• The Soundbar automatically turns off after 20 minutes in the Ready state.
More About Bluetooth
Bluetooth is a technology that enables Bluetooth-compliant devices to interconnect easily with each other using a short wireless connection.
• A Bluetooth device may cause noise or malfunction, depending on usage, if:
– A part of your body is in contact with the receiving/transmitting system of the Bluetooth
device or the Soundbar. – It is subject to electrical variation from obstructions caused by a wall, corner, or ofce partition. – It is exposed to electrical interference from same frequency-band devices including medical
equipment, microwave ovens, and wireless LANs.
• Pair the Soundbar with the Bluetooth device while they are close together.
• The further the distance between the Soundbar and Bluetooth device, the worse the quality is. If the distance exceeds the Bluetooth operational range, the connection is lost.
• In poor reception areas, the Bluetooth connection may not work properly.
• The Bluetooth connection only works when it is close to the unit. The connection will be automatically cut off if the Bluetooth device is out of range. Even within range, the sound quality may be degraded by obstacles such as walls or doors.
• This wireless device may cause electric interference during its operation.
ENG - 21

Using the Samsung Audio Remote App

Installing the Samsung Audio Remote App
To control the Soundbar with your smart device and the Samsung Audio Remote app, download the Samsung Audio Remote app from the Google Play store.
Market se arch : Samsung Au dio Remote
Launching the Samsung Audio Remote App
To launch and use the Samsung Audio Remote app, touch the Audio Remote icon on your smart device, and then follow the directions on the screen.
Audio Remote
• The Samsung Audio Remote app is only compatible with Android mobile phones and mobile devices running Android OS 3.0 or later.
ENG - 22

08 USING THE REMOTE CONTROL

PAIR
PAIR

How to Use the Remote Control

󱂓
󱂔
󱂕
󱂖
PAIR
SOUND
MODE
VOL WOOFER
SOUNDBAR
󱂗
󱂘
󱂙
󱂚
󱂛
󱂜
󱂓
󱂔
󱂕
󱂖
SOUND MODE
Power
Source
Mute
SOUND
MODE
Turns the Soundbar on and off.
Press to select a source connected to the Soundbar.
BT PAIRING mode To turn on “BT PAIRING” mode, change the source to “BT” mode, and then press and hold the (Source) but ton for more than 5 seconds.
Press the (Mute) button to mute the sound. Press it again to unmute the sound.
You can selec t the desired sound effect by choosing STANDARD, or SURROUND SOUND. Select the “STANDARD” mode if you want to enjoy the original sound.
DRC (Dynamic Rang e Control) Lets you apply dynamic range control to Dolby Digital tracks. Press and hold the SOUND MODE button while the Soundbar is powered off to turn DRC (Dynamic Range Control) on or off. With the DRC turned on, loud sound is reduced. (The sound may be distorted.)
Bluetooth Power This feature automatically turns the Soundbar on when it receives a connection request from a previously connected TV or Bluetooth device. The set ting is On by
default.
– Press and hold the SOUND MODE
button for more than 5 seconds to turn off the Bluetooth Power function.
ENG - 23
󱂗
PAIR
Bluetooth
PAIR
Press the PAIR button. “BT PAIRING” appears in the Soundbar’s display. You can connec t the Soundbar to a new Bluetooth device in this mode by selecting the Soundbar from the Bluetooth device's search list.
󱂘
󱂙
Play / Pau se
Up/Down/ Left/Right
Press the p button to pause a music le temporarily. When you press the button again, the music le plays.
Auto Power Down Function The unit turns off automatically in the following situations:
– In D.IN / BT / USB Mode : If there is no audio signal for 20 minutes. – In AUX Mode :
– If the Audio (AUX) Cable is disconnected for 20 minutes. – If there is no KE Y input for 8 hours when the Audio (AUX) Cable is connec ted.
(The Auto Power Down function can be turned off only when the unit is in “AUX” mode.)
– To turn off Auto Power Down function while the unit is in “AUX” mode, press
and hold the p button for 5 seconds. “ON -AUTO POWER DOW N” / “OFF-
AUTO POW ER DOWN” appears on the display.
Press the indicated areas to select Up/Down/Left/Right.
Press Up/Down/Left /Right on the button to select or set functions.
Repeat To use the Repeat function in “USB” mode, press the Up but ton.
Music Skip Press the Right button to select the next music le. Press the Left button to select the
previous music le.
Auto Power Link You can turn Auto Power Link on or off. Auto Power Link is turned on and turned of f by the Left button respectively.
– Auto Power Link : If the Soundbar is connected to your TV through a digital optical
cable, the Soundbar can automatically turn on when you turn on your TV. Press and hold the Left button for 5 seconds to toggle Auto Power Link ON and OFF.
– Auto Power Link is set to ON by default.
ID SET Press and hold the Up button for 5 seconds to complete ID SET (when connec ting to an accessary item).
ENG - 24
Volume Restriction function
PAIR
SOUNDBAR
SOUNDBAR
SOUND
MODE
PAIR
SOUND
MODE
VOL
WOOFER
SOUNDBAR
SOUND
MODE
VOL
WOOFER
SOUNDBAR
SOUNDBAR
SOUNDBAR
To protect your hearing, the Volume Restric tion function restricts the volume to 20 if you turn on the Soundbar when the volume is set higher than 20.
– The default value for the Volume Restric tion function is Off. You must turn it on to
activate it.
– When turned on, the Volume Restric tion function stays on even when the power is
turned off.
– To turn Volume Restric tion on or off, press and hold the Down button on the
remote control for 5 seconds. With Volume Restriction off, “V FREE ” appears on the front display. With the function on, “V LO CK” appears.
󱂚
󱂛
󱂜
Sound Control
WOOFER
VOL
You can selec t TREBLE, BASS, or AUDIO SYNC.
• To control the volume of the treble or bass sound, selec t TREBLE or BASS in Sound Settings, and then adjus t the volume between -6~+6 by using the Up/Down buttons.
• Press and hold the (Sound Control) but ton for about 5 seconds to adjust the sound for each frequency band. 150Hz, 300Hz, 600Hz, 1. 2kHz, 2.5kHz, 5kHz, and 10kHz are selectable using the Left/Right buttons and each can be adjusted to a setting between
-6 to +6 using the Up/Down buttons.
• If the video on the T V and audio from the Soundbar are not synchronised, select AUDIO SYNC in Sound Settings, and then
set the audio delay between 0~300 milliseconds
using the Up/Down buttons. (Not available in “USB” mode.)
AUDIO SYNC is only suppor ted for some functions.
SOUND
MODE
WOOFER
VOL
SOUND
MODE
WOOFER
VOL
Push the WOOFER but ton up or down to adjust the volume of the subwoofer to -12 or between -6 to +6. To set the subwoofer volume level to 0, press the button.
SOUND
MODE
WOOFER
VOL
SOUND
MODE
WOOFER
VOL
Push the VOL button up or down to adjust the volume.
Mute Press the VOL but ton to mute the sound. Press it again to unmute the sound.
by
ENG - 25
Adjusting the Soundbar volume
SOUNDBAR
SOUNDBAR
SOUNDBAR
with a TV remote control
If you have a Samsung TV, you can adjust
theSoundbar’svolumeusingtheIRremote
control that came with your Samsung TV.
First use the TV menu to set the TV audio on your Samsung TV to external speakers, then use your Samsung remote to control the Soundbar’s volume. For more information, see the TV’s user manual. The default mode for this function is control by a Samsung TV remote. If your TV is not a Samsung TV, follow the directions below to change the settings of this function.
1. Turn Off the Soundbar.
BYE
2. If you do not want to use this function, push
up and hold the WOOFER button for 5 seconds repeatedly until “OFF-TV
REMOTE” appears in the display.
4. If you want to return the Soundbar to the
default mode (control by a Samsung TV remote), push up and hold the WOOFER button for 5 seconds repeatedly until “SAMSUNG-TV REMOTE” appears in the display.
(Default mode)
SOUND
MODE
5 Sec
WOOFER
VOL
SAMSUNG-TV REMOTE
– Each time you push the WOOFER button
up and hold it for 5 seconds, the mode switches in the following order: “SAMSUNG-TV REMOTE” (Default mode) → “OFF‑TV REMOTE” → “ALL‑TV REMOTE”.
– This function may not be available,
depending on the remote control.
– Manufacturers supporting this function:
VIZIO, LG, Sony, Sharp, PHILIPS, PANASONIC, TOSHIBA, GRUNDIG, Hisense, RCA
SOUND
MODE
5 Sec
WOOFER
VOL
OFF-TV REMOTE
3. If you want to control the Soundbar with
your TV’s remote, push up and hold the
WOOFER button for 5 seconds repeatedly
until “ALL-TV REMOTE” appears in the display. Then, use your TV’s menu to select external speakers.
SOUND
MODE
5 Sec
WOOFER
VOL
ALL-TV REMOTE
ENG - 26
Loading...
+ 128 hidden pages