Samsung HW-N850 User Manual

FULL MANUAL

HW-N850

Imagine the possibilities

Thank you fo r purchasing this Samsung product.

To receive more complete s ervice, please register

your product at www.samsung.com/register

SAFETY INFORMATION

SAFETY WARNINGS

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF E LECTRIC S HOCK.

DO NOT OP EN.

This symbol indicates that high voltage is present inside. It is dangerous to make any kind of contact with any internal part of this product.

This symbol indicates that this product has included important literature concerning operation and maintenance.

Class II product : This symbol indicates

that it does not require a safety

connection to electrical ear th (ground).

AC voltage : This symbol indicates that

the rated voltage marked with the

symbol is AC voltage.

DC voltage : This symbol indicates that

the rated voltage marked with the

symbol is DC voltage.

Caution, Consult instructions for use :

This symbol instructs the user to

consult the user manual for further

safety related information.

WARNING

• To reduce the risk of re or electric shock, do not expose this appliance to rain or moisture.

CAUTION

• TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

• This apparatus shall always be connected to a AC outlet with a protective grounding connection.

• To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.

• Do not expose this apparatus to dripping or

splashing. Do not put objects lled with

liquids, such as vases on the apparatus.

• To turn this apparatus of f completely, you must pull the power plug out of the wall socket. Consequently, the power plug must be easily and readily accessible at all times.

Wiring the Main Power Supply Plug (UK Only)

IMPORTANT NOTICE

The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug and if it requires replacing, a fuse approved to BS1362 of the same rating must be used. Never use the plug with the fuse cover removed. If the cover is detachable and a replacement is required, it must be of the same colour as the fuse

tted in the plug. Replacement covers are available from your dealer. If the tted plug is not

suitable for the power points in your house or the cable is not long enough to reach a power point, you should obtain a suitable safety approved extension lead or consult your dealer for assistance.

ENG - ii

However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect the plug to a mains socket as there is a risk of shock hazard from the

bared exible cord. Never attempt to insert bare

wires directly into a mains socket. A plug and fuse must be used at all times.

IMPORTANT

The wires in the mains lead are coloured in accordance with the following code:– BLUE = NEUTRAL BROWN = LIVE As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows:– The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.

WARNING : DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE LET TER E OR BY THE EARTH SYMBOL , OR COLOURED GREEN OR GREEN AND YELLOW.

PRECAUTIONS

1. Ensure that the AC power supply in your

house complies with the power

requirements listed on the identication

sticker located on the bottom of your product. Install your product horizontally, on a suitable base (furniture), with enough space around it for ventilation (7~10 cm). Make sure the ventilation slots are not

covered. Do not place the unit on ampliers

or other equipment which may become hot. This unit is designed for continuous use. To fully turn off the unit, disconnect the AC plug from the wall outlet. Unplug the unit if you intend to leave it unused for a long period of time.

2. During thunderstorms, disconnect the AC

plug from the wall outlet. Voltage peaks due to lightning could damage the unit.

3. Do not expose the unit to direct sunlight or

other heat sources. This could lead to overheating and cause the unit to malfunction.

4. Protect the product from moisture (i.e.

vases), and excess heat (e.g. a replace) or

equipment creating strong magnetic or

electric elds. Unplug the power cable from

the AC wall socket if the unit malfunctions. Your product is not intended for industrial use. It is for personal use only. Condensation may occur if your product has been stored in cold temperatures. If transporting the unit during the winter, wait approximately 2 hours until the unit has reached room temperature before using.

5. The battery used with this product contains

chemicals that are harmful to the environment. Do not dispose of the battery in the general household trash. Do not expose the battery to excess heat, direct

sunlight, or re. Do not short circuit,

disassemble, or overheat the battery. Danger of explosion if the battery is replaced incorrectly. Replace only with the same or equivalent type.

ENG - iii

ABOUT THIS MANUAL

The user manual has two parts: this simple paper USER MANUAL and a detailed FULL MANUAL you can download.

USER MANUAL

See this manual for safety instructions, product installation,

components, connections, and product specications.

FULL MANUAL

You can access the FULL MANUAL on Samsung’s on-line customer support centre by scanning the QR code. To see the manual on your PC or mobile device, download the manual in document format from Samsung’s website. (http://www.samsung.com/support)

Design, specications, and App screen are subject to change without prior notice.

CONTENTS

01 Checking the Components 2

Inserting Batteries before using the Remote Control (AA batteries X 2) ------------------------- 2

02 Product Overview 3

Front Panel / Top Panel of the Soundbar ------------------------- 3

Bottom Panel of the Soundbar ------------------------- 4

03 Connecting the Soundbar 5

Connecting Electrical Power

Connecting the Soundbar to the Subwoofer

– Automatic connection between the Subwoofer and the Soundbar – Manually connecting the Subwoofer if automatic connection fails

Connecting the SWA-9000S to a Soundbar (Sold Separately)

-------------------------

04 Connecting to a TV 10

Method 1. Connecting with a Cable

– Connecting a TV using an HDMI Cable – Connecting using an Optical Cable

-------------------------

ENG - iv

6 7

Method 2. Connecting Wirelessly

– Connecting a TV via Bluetooth – Connecting via Wi-Fi

-------------------------

05 Connecting an External Device 16

12 14

Connecting using an HDMI Cable (Dolby Atmos® supported)

Connecting using an HDMI Cable

Connecting using an Optical Cable

-------------------------

06 Connecting a Mobile Device 19

Connecting via Bluetooth

Connecting via Wi-Fi (Wireless Network)

-------------------------

07 Connecting an Amazon product 24

Connect and use with an Amazon product (Amazon Echo) ------------------------- 24

Use voice commands to control the Soundbar

-------------------------

08 Using the Remote Control 27

How to Use the Remote Control

Adjusting the Soundbar volume with a TV remote control

Using the Hidden Buttons (Buttons with more than one function)

Output specications for the different sound effect modes

-------------------------

09 Installing the Wall Mount 32

Installation Precautions

Wallmount Components

-------------------------

10 Software Update 34

11 Troubleshooting 35

12 Licence 36

13 Open Source Licence Notice 37

14 Important Notes About Service 37

15 SpecicationsandGuide 38

Specications

-------------------------

ENG - v

01 CHECKING THE COMPONENTS

PAIR

SOUND MODE

VOL WOOFER

SOUNDBAR

Soundbar Main Unit Remote Control

/ Bat teries

Subwoofer

1 2

x 2

Power Cord (Subwoofer) Power Cord

(Main Unit)

x 2

Bracket-Wall Mount

x 2

(M4 x L10)

Wall Mount Guide Holder-Screw Screw

• For more information about the power supply and power consumption, refer to the label attached to the product. (Label : Bottom of the Soundbar Main Unit)

• The power components are labelled (1, 2). For more information about power connections, see page 5.

• For Soundbar wall mounting components, see page 32.

• To purchase additional components or optional cables, contact a Samsung Service Centre or Samsung Customer Care.

• The appearance of the accessories may differ slightly from the illustrations above.

Inserting Batteries before using the Remote Control (AA batteries X 2)

Slide the battery cover in the direction of the arrow until it is completely removed. Insert 2 AA batteries (1.5V) oriented so that their polarity is correct. Slide the battery cover back into position.

ENG - 2

02 PRODUCT OVERVIEW

Front Panel / Top Panel of the Soundbar

Position the product so that the "Samsung Harman Kardon" logo is located on the top.

Top

Panel

󱂓 󱂔 󱂕

󱂖

󱂓

󱂔

󱂕

󱂖

(Power) Button

Turns the power on and off.

(Source) But ton

Selects the source input mode.

Input mode Display

Optical Digital input D.IN

ARC (HDMI OUT) input D.IN  TV ARC (Auto conversion)

HDMI input HDMI 1 / HDMI 2

Wi-Fi mode WIFI

BLUETOOTH mode BT

• To turn on “BT PAIRING” mode, change the source to “BT” mode, and then press and hold the

 (Source) button on the top panel for more than 5 seconds.

-/+ (Volume) But ton

Adjusts the volume.

• When adjusted, the volume level appears on the Soundbar ’s front display.

Display

Displays the product’s status and current mode.

• When you plug in the AC cord, the power button will begin working in 4 to 6 seconds.

• When you turn on this unit, there will be a 4 to 5 second delay before it produces sound.

• If you want to enjoy sound only from the Soundbar, you must turn off the TV’s speakers in the Audio Setup menu of your TV. Refer to the owner ’s manual supplied with your TV.

ENG - 3

Bottom Panel of the Soundbar

SERVICE

NETWORK

ID SET (WOOFER/REAR)

DIGITAL AUDIO IN

(OPTICAL)

HDMI IN 1

HDMI IN 2

HDMI OUT (TV-ARC)

DIGITAL AUDIO IN

(OPTICAL)

HDMI IN 1

HDMI IN 2

HDMI OUT

(TV-ARC)

POWER

SERVICE

NETWORK

ID SET (WOOFER/REAR)

DIGITAL AUDIO IN

(OPTICAL)

HDMI IN 1

HDMI IN 2

HDMI OUT (TV-ARC)

DIGITAL AUDIO IN

(OPTICAL)

HDMI IN 1

HDMI IN 2

HDMI OUT

(TV-ARC)

SERVICE

NETWORK

ID SET (WOOFER/REAR)

󱂕󱂔 󱂖

POWER

ID SET (WOOFER/REAR)

󱂓

POWER

󱂓

Connect the Soundbar's AC power cord.

POWER

NETWORK

ID SET (WOOFER/REAR)

Press to connect the Soundbar to surround speakers and a subwoofer wirelessly.

󱂔

• Press and hold the Up button on the remote for 5 seconds to complete ID SET.

NETWORK

󱂕

Press to connect to a wireless network (Wi-Fi) via the SmartThings app.

SERVICE

󱂖

Connect a USB storage device to upgrade the product's software.

DIGITAL AUD IO IN (OPTIC AL)

󱂗

Connect to the digital (optical) output of an ex ternal device.

SERVICE

ID SET (WOOFER/REAR)

NETWORK

DIGITAL AUDIO IN

(OPTICAL)

HDMI IN 1

HDMI IN 2

HDMI OUT

(TV-ARC)

(OPTICAL)

HDMI IN 1

HDMI IN 2

HDMI OUT (TV-ARC)

󱂗

󱂘

󱂙

HDMI IN 1 / HD MI IN 2

Inputs digital video and audio signals simultaneously using an HDMI cable.

󱂘

Use when connecting a supported external device.

HDMI OUT (TV-ARC)

󱂙

Connect to the HDMI (ARC) jack on a TV.

• When disconnecting the power cord from a wall outlet, pull the plug. Do not pull the cable.

• Do not connect this unit or other components to an AC outlet until all connections between components are complete.

ENG - 4

03 CONNECTING THE SOUNDBAR

SERVICE

NETWORK

ID SET (WOOFER/REAR)

DIGITAL AUDIO IN

(OPTICAL)

HDMI IN 1

HDMI IN 2

HDMI OUT

(TV-ARC)

Connecting Electrical Power

Use the power components (

1, 2

) to connect the Subwoofer and Soundbar to an electrical outlet in

the following order:

Connect the power cord to the Subwoofer.

Connect the power cord to the Soundbar.

See the illustrations below.

• For more information about the required electrical power and power consumption, refer to the label attached to the product. (Label : Bottom of the Soundbar Main Unit)

1 Power Cord

POWER

Rear of Subwoofer

Connecting

Electric al Power

POWER

Bott om of the Soundba r

Main Unit

POWER

2 Power Cord

Connecting Ele ctrical Power

ENG - 5

Connecting the Soundbar to the Subwoofer

When the subwoofer is connected, you can enjoy rich bass sound.

Automatic connection between the Subwoofer and the Soundbar

When you turn the power on after connecting the power cables to the Soundbar and subwoofer, the subwoofer is automatically connected to the Soundbar.

• When auto pairing is complete, the blue indicators at the rear of the subwoofer turn on.

LED Indicator Lights on the Rear of Subwoofer

LED Status Description Resolution

Successfully connected (normal operation)

Blue

Red On

Red and

blue

Standby (with the Soundbar main unit turned off)

Blinking

Connection failed

Standby (with the Soundbar main unit turned off)

Connection failed

Blinking Malfunction

Check the power supply to the Soundbar main unit.

Connect again. (Refer to the instructions on manual connection on page 7.)

Check the power supply to the Soundbar main unit.

Connect again. (Refer to the instructions on manual connection on page 7.)

See the contact information for the Samsung Service Centre in this manual.

ENG - 6

Manually connecting the Subwoofer if automatic connection fails

Before per forming the manual connection procedure below:

• Check whether the power cables for the Soundbar and subwoofer are connected properly.

• Make sure that the Soundbar is turned on.

1. Press and hold ID SET on the rear of the subwoofer for at least 5 seconds.

• The red indicator on the rear of the subwoofer turns off and the blue indicator blinks.

5 Sec

Rear of Subwoofer

Blue LED B linking Fast

2. Press and hold the Up button on the remote control for at least 5 seconds.

• The ID SET message appears on the display of the Soundbar for a moment, and then it

disappears.

• The Soundbar will automatically power on when ID SET is complete.

PAIR

5 Sec

“Sam sung Harman Kard on” logo is on the top

3. Check if the LINK LED is solid blue (connection complete).

The LINK LED indicator stops blinking and glows a solid blue when a connection is established between the Soundbar and the

Blue is On

Wireless Subwoofer.

ID SET

ENG - 7

NOTES

• Do not connect the power cord of this product or your TV to a wall outlet until all connections between components are complete.

• Before moving or installing this product, be sure to turn off the power and disconnect the power cord.

• If the main unit is powered off, the wireless subwoofer will go into stand-by mode and the STANDBY LED on the rear will be Red after blinking Blue several times.

• If you use a device that uses the same frequency (5.8GHz) as the Soundbar near the Soundbar, interference may cause some sound interruption.

• The maximum transmission distance of the wireless signal of the main unit is about 10 meters, but may vary depending on your operating environment. If a steel-concrete or metallic wall is between the main unit and the wireless subwoofer the system may not operate at all, because the wireless signal cannot penetrate metal.

PRECAUTIONS

• Wireless receiving antennas are built into the wireless subwoofer. Keep the units away from water and moisture.

• For optimal listening performance, make sure that the area around the wireless subwoofer and Wireless Receiver Module (Sold separately) location is clear of any obstructions.

Connecting the SWA-9000S to a Soundbar (Sold Separately)

Expand to true wireless surround sound by connecting the Samsung Wireless Rear Speaker Kit (SWA-9000S) to your Soundbar (Sold separately).

1. Connect the Wireless Receiver Module to 2 Surround Speakers.

– The speaker cables are color coded.

SURROUND SPEAKERS OUT SPEAKER IMPEDANCE : 3Ω

SURROUND-LEFT SURROUND-RIGHT

SURROUND-LEFT

ID SET

ENG - 8

SURROUND-RIGHT

POWER

2. Check the standby status of the Wireless Receiver Module after plugging it into an electrical outlet.

POWER

ID SET

LINK

• The LINK LED indicator (blue LED) on the Wireless Receiver Module blinks. If the LED does not

blink, press the ID SET button on the back of the Wireless Receiver Module with a pen tip for 5~6 seconds until the LINK LED indicator blinks (in Blue). For more about the LED, please refer to the SWA-9000S user manual.

SURROUND SPEAKERS OUT SPEAKER IMPEDANCE : 3Ω

ID SET

5 Sec

STANDBY

LINK

Blue blinking

POWER

3. Press and hold the Up button on the remote control for at least 5 seconds.

• The ID SET message appears on the display of the Soundbar for a moment, and then it disappears.

• The Soundbar will automatically power on when ID SET is complete.

PAIR

5 Sec

“Sam sung Harman Kard on” logo is on the top

ID SET

CAUTION

• If your Soundbar was playing music when it connects to the SWA-9000S, you may hear some

stuttering from the woofer as the connection nalises.

4. Check if the LINK LED is solid blue (connection complete)

The LINK LED indicator stops blinking and

STANDBY

LINK

glows a solid blue when a connection is established between the Soundbar and the Wireless Receiver Module.

Blue is On

5. If SWA-9000S is not connected, repeat the procedure from Step 2.

ENG - 9

04 CONNECTING TO A TV

Hear TV sound from your Soundbar through wired or wireless connections.

• When the Soundbar is connected to selected Samsung TVs, the Soundbar can be controlled using the TV’s remote control.

– This feature is available on 2017 and later Samsung Smart TVs that support Bluetooth when the

Soundbar is connected to the TV using an optical cable.

– This function also allows you to use the TV menu to adjust the sound eld and various settings

as well as the volume and mute.

Method 1. Connecting with a Cable

When the audio in a broadcast is encoded in Dolby Digital and the “Digital Output Audio Format” on your TV is set to PCM, we recommend that you change the setting to Dolby Digital. When the setting on the TV is changed, you will experience better sound quality. (The TV menu may use different words for Dolby Digital and PCM depending on the TV manufacturer.)

Connecting a TV using an HDMI Cable

Connec t to the HDMI IN

(ARC) p ort of your T V.

HDMI Cable

(not supplied)

Bott om of the Soundba r

󱂓

HDMI IN

(ARC)

Connec t to the HDMI OUT ( TV-ARC)

port o f the Soundbar mai n unit.

Top of the Soun dbar

HDMI OUT

(TV-ARC)

󱂔

TV ARC

1. With the Soundbar and TV turned on, connect the HDMI cable (not supplied) as shown in the gure.

2. “TV ARC” appears in the display window of the Soundbar main unit and the Soundbar plays TV

sound.

• If TV sound is inaudible, press the (Source) button on the remote control or on the top of the Soundbar to switch to “D.IN” mode. The screen displays “D.IN” and “TV ARC ” in sequence, and TV sound is played.

ENG - 10

+ 32 hidden pages