Samsung HW-M460 Operating Instructions

FULL MANUAL

HW-M460

Imagine the possibilities

Thank you fo r purchasing this Samsung product.

To receive more complete s ervice, please register

your product at www.samsung.com/register

SAFETY INFORMATION

SAFETY WARNINGS

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE THE COVER (OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.

CAUTION

RISK OF E LECTRIC S HOCK.

DO NOT OP EN.

This symbol indicates that high voltage
is present inside. It is dangerous to make
any kind of contact with any internal
part of this product.

This symbol indicates that important
literature concerning operation and
maintenance has been included with
this product.

Class II product : This symbol indicates

that it does not require a safety

connection to electrical ear th (ground).

AC voltage : This symbol indicates that

the rated voltage marked with the

symbol is AC voltage.

DC voltage : This symbol indicates that

the rated voltage marked with the

symbol is DC voltage.

Caution, Consult instructions for use :

This symbol instructs the user to consult

the user manual for fur ther safety

related information.

WARNING

• To reduce the risk of re or electric shock, do
not expose this appliance to rain or moisture.

CAUTION

• TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.

• This apparatus shall always be connected to a
AC outlet with a protective grounding
connection.

• To disconnect the apparatus from the mains,
the plug must be pulled out from the mains
socket, therefore the mains plug shall be
readily operable.

• Do not expose this apparatus to dripping or

splashing. Do not put objects lled with

liquids, such as vases on the apparatus.

• To turn this apparatus of f completely, you
must pull the power plug out of the wall
socket. Consequently, the power plug must
be easily and readily accessible at all times.

Wiring the Main Power Supply
Plug (UK Only)

IMPORTANT NOTICE

The mains lead on this equipment is supplied with
a moulded plug incorporating a fuse. The value of
the fuse is indicated on the pin face of the plug
and if it requires replacing, a fuse approved to
BS1362 of the same rating must be used.
Never use the plug with the fuse cover removed.
If the cover is detachable and a replacement is
required, it must be of the same colour as the fuse

tted in the plug. Replacement covers are
available from your dealer. If the tted plug is not

suitable for the power points in your house or the
cable is not long enough to reach a power point,
you should obtain a suitable safety approved
extension lead or consult your dealer for assistance.

ENG - ii

However, if there is no alternative to cutting off the
plug, remove the fuse and then safely dispose of
the plug. Do not connect the plug to a mains
socket as there is a risk of shock hazard from the

bared exible cord. Never attempt to insert bare

wires directly into a mains socket. A plug and fuse
must be used at all times.

IMPORTANT

The wires in the mains lead are coloured in
accordance with the following code:– BLUE =
NEUTRAL BROWN = LIVE As these colours may not
correspond to the coloured markings identifying
the terminals in your plug, proceed as follows:– The
wire coloured BLUE must be connected to the
terminal marked with the letter N or coloured
BLUE or BLACK. The wire coloured BROWN must
be connected to the terminal marked with the
letter L or coloured BROWN or RED.

WARNING : DO NOT CONNECT EITHER WIRE TO
THE EARTH TERMINAL WHICH IS MARKED WITH
THE LET TER E OR BY THE EARTH SYMBOL ,
OR COLOURED GREEN OR GREEN AND YELLOW.

PRECAUTIONS

1. Ensure that the AC power supply in your

house complies with the power

requirements listed on the identication

sticker located on the back of your product.
Install your product horizontally, on a
suitable base (furniture), with enough space
around it for ventilation (7~10 cm). Make sure
the ventilation slots are not covered. Do not

place the unit on ampliers or other

equipment which may become hot. This unit
is designed for continuous use. To fully turn
off the unit, disconnect the AC plug from the
wall outlet. Unplug the unit if you intend to
leave it unused for a long period of time.

2. During thunderstorms, disconnect the AC

plug from the wall outlet. Voltage peaks due
to lightning could damage the unit.

3. Do not expose the unit to direct sunlight or

other heat sources. This could lead to
overheating and cause the unit to
malfunction.

4. Protect the product from moisture (i.e.

vases), and excess heat (e.g. a replace) or

equipment creating strong magnetic or

electric elds. Unplug the power cable from

the AC wall socket if the unit malfunctions.
Your product is not intended for industrial
use. It is for personal use only. Condensation
may occur if your product has been stored in
cold temperatures. If transporting the unit
during the winter, wait approximately
2 hours until the unit has reached room
temperature before using.

5. The battery used with this product contains

chemicals that are harmful to the
environment. Do not dispose of the battery
in the general household trash. Do not
expose the battery to excess heat, direct

sunlight, or re. Do not short circuit,

disassemble, or overheat the battery.
Danger of explosion if the battery is replaced
incorrectly. Replace only with the same or
equivalent type.

ENG - iii

ABOUT THIS MANUAL

The user manual has two parts: this simple paper USER MANUAL and a detailed FULL MANUAL you can
download.

USER MANUAL

See this manual for safety instructions, product installation,

components, connections, and product specications.

FULL MANUAL

You can access the customer support centre by scanning the
QR code. To see the manual on your PC or mobile device,
download the manual in document format from the website.
(http://www.samsung.com/support)

Design and specications are subject to change without prior notice.

CONTENTS

01 Checking the Components 2

Inserting Batteries before using the Remote Control (AA batteries X 2) ------------------------- 2

02 Product Overview 3

Front Panel / Right Side Panel of the Soundbar ------------------------- 3

Bottom Panel of the Soundbar ------------------------- 4

03 Connecting the Soundbar 5

Connecting Electrical Power

Connecting the Soundbar to the Subwoofer

– Automatic connection between the subwoofer and the Soundbar
– Manually connecting the subwoofer if automatic connection fails

-------------------------

-------------------------

-------------------------

-------------------------

04 Connecting to your TV 9

Method 1. Connecting with a Cable

– Connecting a TV using an HDMI Cable
– Connecting using an Optical Cable

Method 2. Connecting Wirelessly

– Connecting a TV via Bluetooth

-------------------------

-------------------------

-------------------------

-------------------------

-------------------------

ENG - iv

5

6

6
7

9

9

10

11

11

05 Connecting an External Device 13

Connecting using an HDMI Cable

Connecting using an Optical or Analogue Audio (AUX) Cable

-------------------------

-------------------------

06 Connecting a USB 15

07 Connecting a Mobile Device 17

Connecting via Bluetooth

Using the Samsung Audio Remote App

– Installing the Samsung Audio Remote App
– Launching the Samsung Audio Remote App

-------------------------

-------------------------

-------------------------

-------------------------

20

20
20

08 Using the Remote Control 21

How to Use the Remote Control

Adjusting the Soundbar volume with a TV remote control ------------------------- 24

Using the Hidden Buttons

Output specications for the different sound effect modes

-------------------------

-------------------------

-------------------------

25

25

09 Installing the Wall Mount 26

Installation Precautions

Wallmount Components

Detaching the Soundbar from the Wall

-------------------------

-------------------------

-------------------------

26

26

29

13

14

17

21

10 Software Update 29

Updating Procedure

If UPDATE is not displayed

-------------------------

-------------------------

30

30

11 Troubleshooting 31

12 Licence 32

13 Open Source Licence Notice 32

14 Important Notes About Service 32

15 SpecicationsandGuide 33

Specications

-------------------------

ENG - v

33

01 CHECKING THE COMPONENTS

Soundbar Main Unit Subwoofer Remote Control / Batteries

1 2 3

Bluetooth

Surround

POWER

SOUND
MODE

VOL WOOFER

SOUNDBAR

Power Cord

(Subwoofer)

AC/DC Adapter

(Main Unit)

Power Cord

(AC/DC Adapter)

• The power connection steps are labelled (1, 2, 3). For more information about power

connections, see page 5.

• For Soundbar wall mounting components, see page 26.

• Micro USB to USB adapter and HDMI cables are sold separately. To purchase, contact a Samsung
Service Centre or Samsung Customer Care.

• The appearance of the accessories may differ slightly from the illustrations above.

Inserting Batteries before using the Remote Control (AA batteries X 2)

Slide the battery cover in the direction of the arrow until it is completely removed. Insert 2 AA batteries

(1.5V) oriented so that their polarity is correct. Slide the battery cover back into position.

ENG - 2

02

PRODUCT OVERVIEW

Front Panel / Right Side Panel of the Soundbar

Position the product so that the
SAMSUNG logo is located on the top.

Right Sid e of the Soundbar

󱂓

Display

󱂓

Displays the product’s status and current mode.

+/- (Volume) But ton

Adjusts the volume.

󱂔

• When adjusted, the volume level appears on the Soundbar ’s front display.

󱂕

󱂖

(Power) Button

Turns the power on and off.

(Source) But ton

Selects the source input mode.

Input mode Display

Optical Digital input D.IN

ARC (HDMI OUT) input D.IN  TV ARC (Auto conversion)

AUX input AUX

HDMI input HDMI

BLUETOOTH mode BT

USB mode USB

• To turn on “BT PAIRING” mode, change the source to “ BT” mode, and then press and hold the
(Source) button for more than 5 seconds.

󱂔

󱂕 󱂖

• When you plug in the AC cord, the power button will begin working in 4 to 6 seconds.

• When you turn on this unit, there will be a 4 to 5 second delay before it produces sound.

• If you want to enjoy sound only from the Soundbar, you must turn off the TV’s speakers in the Audio
Setup menu of your TV. Refer to the owner ’s manual supplied with your TV.

ENG - 3

Bottom Panel of the Soundbar

DIGITAL AUDIO IN

󱂓

(OPTICAL)

HDMI IN

󱂔

󱂕

DIGITAL AUD IO IN (OPTIC AL)

󱂓

Connect to the digital (optical) output of an ex ternal device.

USB (5V 0. 5A)

󱂔

Connect a USB device here to play music les on the USB device through the Soundbar.

AUX IN

󱂕

Connect to the Analogue output of an external device.

HDMI IN

Inputs digital video and audio signals simultaneously using an HDMI cable.

󱂖

Connect to the HDMI output of an external device.

HDMI OUT (TV-ARC)

󱂗

Connect to the HDMI (ARC) jack on a TV.

USB (5V 0.5A)

AUX IN

HDMI OUT

(TV-ARC)

DIGITAL AUDIO IN

HDMI IN

(OPTICAL)

USB (5V 0.5A)

HDMI OUT

(TV-ARC)

AUX IN

DC 24V

DC 24V

󱂗

󱂖

󱂘

DC 24V

DC 24V (P ower Supply In)

󱂘

Connect the AC/DC power adapter.

• When disconnecting the power cable of the AC/DC power adaptor from a wall outlet, pull the plug.
Do not pull the cable.

• Do not connect this unit or other components to an AC outlet until all connections between
components are complete.

ENG - 4

03 CONNECTING THE SOUNDBAR

Connecting Electrical Power

Use the power components (1, 2, 3) to connect the units to electrical outlets in the following order:

1.) Subwoofer  2.) Soundbar Main Unit. See the illustrations below.

• For more information about the required electrical power and power consumption, refer to the
label attached to the product. (Label : Bottom of the Soundbar Main Unit)

1 Power Cord

3 Power Cord

POWER

DC 24V

Connecting

Electric al Power

2 AC/DC Adapter

Rear of Subwoofer

Connecting

Electric al Power

HDMI IN

HDMI OUT
(TV-ARC)

DC 24V

DC 24V

Bott om of the

Soundbar Main Unit

• Make sure to rest the AC/DC Adapter at on a table or the oor. If you place the AC/DC Adapter so
that it is hanging with the AC cord input facing upwards, water or other foreign substances could
enter the Adapter and cause the Adapter to malfunction.

ENG - 5

Connecting the Soundbar to the Subwoofer

When the subwoofer is connected, you can enjoy rich bass sound.

Automatic connection between the subwoofer and the Soundbar

When you turn the power on after connecting the power cables to the Soundbar and subwoofer, the
subwoofer is automatically connected to the Soundbar.

• When auto pairing is complete, the blue indicators at the rear of the subwoofer turn on.

LED Indicator Lights on the Rear of Subwoofer

LED Status Description Resolution

Successfully connected
(normal operation)

Standby (with the Soundbar
main unit turned off)

Connection failed

-

Check if the power cable to the main
Soundbar unit is connected properly or
wait for a while. (If blinking persists, try
manually connecting the subwoofer.
See page 7.)

Check if the power cable to the main
Soundbar unit is connected properly.

Connect again. See the instructions for
manual connection on page 7.

See the contact information for the
Samsung Service Centre in the manual.

Blue

Red On

Red and

blue

On

Blinking Recovering the connection

Blinking Malfunction

ENG - 6

Manually connecting the subwoofer if automatic connection fails

Bluetooth

POWER

SOUNDBAR

Check before performing the manual connection

• Check whether the power cables for the Soundbar and subwoofer are connected properly.

• Make sure that the Soundbar is turned on.

1. Press and hold ID SET on the rear of the subwoofer for at least 5 seconds.

The red indicator on the rear of the subwoofer turns off and the blue indicator blinks.

5 Sec

Rear of Subwoofer

2. Turn off the Soundbar.

3. Press and hold the VOL button on the remote control for at least 5 seconds with the Soundbar

turned off (OFF).

4. The ID SET message appears on the display of the Soundbar for 1.3 seconds, and then disappear.

5 Sec

Surround

SOUND

MODE

WOOFER

VOL

ID SET

5. When the blue indicator on the subwoofer blinks, turn on the Soundbar’s power by pressing
(Power) button on the right side of the main unit or on the remote control.

6. When the connection is successfully established, the blue indicator on the rear of the subwoofer

stops blinking and glows continuously.

• If the connection process fails, the blue indicator will ash continuously. Go to Step 1 and start again.

NOTES

• Do not connect the power cord of this product or your TV to a wall outlet until all connections
between components are complete.

• Before moving or installing this product, be sure to turn off the power and disconnect the power
cord.

ENG - 7

• If the main unit is powered off, the wireless subwoofer will go into stand-by mode and the
STANDBY LED on the rear will be Red after blinking Blue several times.

• If you use a device that uses the same frequency (5.8GHz) as the Soundbar near the Soundbar,
interference may cause some sound interruption.

• The maximum transmission distance of the wireless signal of the main unit is about 10 meters, but
may vary depending on your operating environment. If a steel-concrete or metallic wall is between
the main unit and the wireless subwoofer the system may not operate at all, because the wireless
signal cannot penetrate metal.

PRECAUTIONS

• Wireless receiving antennas are built into the wireless subwoofer. Keep the units away from water
and moisture.

• For optimal listening performance, make sure that the area around the wireless subwoofer and
Wireless Receiver Module (Sold separately) location is clear of any obstructions.

Expand to true wireless surround sound by connecting the Samsung Wireless Rear Speaker
Kit (SWA-8500S) to your Soundbar (Sold separately). For more information, see the
Samsung Wireless Rear Speaker Kit manual.

ENG - 8

04 CONNECTING TO YOUR TV

Hear TV sound from your Soundbar through wired or wireless connections.

• When the Soundbar is connected to a Samsung smart TV released in 2017 or later, the Soundbar
can be controlled using the TV’s remote control.

– This function also allows you to use the TV menu to adjust the sound eld and various settings

as well as the volume and mute.

Method 1. Connecting with a Cable

Connecting a TV using an HDMI Cable

Check th e (ARC) at

HDMI IN po rt of your TV.

󱂓

HDMI IN

(ARC)

1. With the Soundbar and TV turned on, connect the HDMI cable (not supplied) as shown in the gure.

2. “TV ARC” appears in the display window of the Soundbar main unit and the Soundbar plays TV

sound.

• If TV sound is inaudible, press the (Source) button on the remote control or on the right side
of the Soundbar to switch to “D.IN” mode. The screen displays “D.IN” and “T V ARC” in sequence,
and TV sound is played.

• If “T V ARC” does not appear in the display window of the Soundbar main unit, conrm that the
cable is connected to the correct port.

• Use the volume buttons on the TV’s remote control to change the volume on the Soundbar.

HDMI Cable

(not supplied)

Check th e HDMI OUT (T V-ARC)

port o f the Soundbar mai n unit.

󱂔

TV ARC

Bott om of the Soundba r

HDMI IN

HDMI OUT

(TV-ARC)

Right Sid e of the Soundbar

ENG - 9

NOTES

• HDMI is an interface that enables the digital transmission of video and audio data with just a single
connector.

• If the TV provides an ARC port, connect the HDMI cable to the HDMI IN (ARC) port.

• We recommend you use a coreless HDMI cable if possible. If you use a cored HDMI cable, use one
whose diameter is less than 14 mm.

• Anynet+ must be turned on.

• This function is not available if the HDMI cable does not support ARC.

Connecting using an Optical Cable

Bott om of the Soundba r

DIGITAL AUDIO IN
(OPTICAL)

USB (5V 0.5A)

OPTICAL OUT

󱂓

Optic al Cable

(not supplied)

󱂔

D.IN

1. Connect the DIGITAL AUDIO IN (OPTICAL) jack on the Soundbar to the OPTICAL OUT jack of the TV

with a digital optical cable (not supplied).

2. Press the (Source) button on the right side panel or remote control, and then select mode
“D.IN”.

• When the Soundbar is connected to a Samsung smart TV released in 2017 or later, the
Bluetooth POWER function automatically turns on to enable the Soundbar to be controlled with
the TV remote control. (See page 23 for details on Bluetooth POWER.)

Auto Power Link

Auto Power Link automatically turns on the Soundbar when the TV is turned on.

1. Connect the Soundbar and a TV with a digital optical cable (not supplied).

2. Press the (Source) button on the right side panel or on the remote control, and then select
“D.IN”.

Right Sid e of the Soundbar

ENG - 10

3. Press the Left button on the remote control for 5 seconds to turn Auto Power
Link on or off.

• Auto Power Link is set to ON by default.
(To turn off this function, turn off Auto Power using the Soundbar.)

• Depending on the connected device, Auto Power Link may not function.

• This function is only available in the “D.IN” mode.

Method 2. Connecting Wirelessly

Connecting a TV via Bluetooth

When a TV is connected using Bluetooth, you can hear stereo sound without the hassle of cabling.

• Only one TV can be connected at a time.

The initial connection

1. Press the (Source) button on the right side panel or on the remote control, and then select
“BT”.

2. Change “BT” to “BT PAIRING”.

• If “BT READY” appears, press and hold the (Source) button on the right side panel of the
Soundbar or on the remote control for more than 5 seconds to display “BT PAIRING”.

3. Select Bluetooth mode on the TV. (For more information, see the TV’s manual.)

4. Select “[AV] S amsung Soundbar Mxxx M-Series” from the list on TV’s screen.

An available Soundbar is indicated with “Need Pairing” or “Paired” on the TV Bluetooth device list.
To connect to the Soundbar, select the message and establish a connection.

• When the TV is connected, [TV Name] → “BT” appears on the Soundbar’s front display.

5. You can now hear TV sound from the Soundbar.

If the device fails to connect

• If the previously connected Soundbar listing (e.g. “[AV] Samsung Soundbar Mxxx M-Series ”)

appears in the list, delete it.

• In “BT” mode, press and hold the (Source) button for more than 5 seconds on the right side
panel of the Soundbar or on the remote control to switch to “BT PAIRING” mode.
Then, select “[ AV] Samsung Soundbar Mxxx M-Series” from the TV’s search list.

ENG - 11

What are the BT READY and BT PAIRING statuses?

• BT READY : In this mode, you can search for previously connected TVs or connect to the Soundbar
from a previously connected mobile device.

• BT PAIRING : In this mode, you can connect to a new device. (While in “BT” mode, press and hold the

(Source) button for more than 5 seconds on the right side of the Soundbar or on the remote

control.)

NOTES

• If asked for a PIN code when connecting a Bluetooth device, enter <0000>.

• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the
Soundbar and the Bluetooth device exceeds 10 meters.

• The Soundbar automatically turns off after 5 minutes in the Ready state.

• The Soundbar may not perform Bluetooth search or connection correctly under the following
circumstances:

– If there is a strong electrical eld around the Soundbar.
– If several Bluetooth devices are simultaneously paired with the Soundbar.
– If the Bluetooth device is turned off, not in place, or malfunctions.

• Electronic devices may cause radio interference. Devices that generate electromagnetic waves
must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc.

Disconnecting the Soundbar from the TV

Press the (Source) button on the right side panel or on the remote control and switch to any mode
but “BT”.

• Disconnecting takes time because the TV must receive a response from the Soundbar.
(The time required may differ, depending on the TV model.)

ENG - 12

05 CONNECTING AN EXTERNAL DEVICE

Connect to an external device via a wired or wireless network to play the external device’s sound
through the Soundbar.

Connecting using an HDMI Cable

Bott om of the Soundba r

External Dev ice

HDMI OUT

HDMI IN

(ARC)

HDMI Cable (not supplied)

󱂓

HDMI Cable

(not supplied)

󱂔

HDMI IN

HDMI OUT

(TV-ARC)

󱂕

HDMI

󱂖

1. Connect an HDMI cable (not supplied) from the HDMI IN jack on the back of the product to the

HDMI OUT jack on your digital device.

2. Connect an HDMI cable (not supplied) from the HDMI OUT (TV-ARC) jack on the back of the

product to the HDMI IN jack on your TV.

3. Press the (Source) button on the right side panel or on the remote control, and then select
“HDMI”.

4. “HDMI” mode is displayed on the Soundbar display panel and sound plays.

Right Sid e of the Soundbar

ENG - 13

Connecting using an Optical or Analogue Audio (AUX) Cable

BD / DVD play er / Set-top box /

Game cons ole

OPTICAL OUT

R L

- AUDIO -

󱂓

Optic al Cable

(not supplied)

󱂔

Audio (AU X) Cable

(not supplied)

DIGITAL AUDIO IN
(OPTICAL)

USB (5V 0.5A)

AUX IN

Bott om of the Soundba r

Right Sid e of the Soundbar

1 Optical Cable

X Connect DIGITAL AUDIO IN (OP TICAL) on the main unit to the OPTICAL OUT jack of the Source

Device using a digital optical cable (not supplied).

Y Select “D.IN” mode by pressing the (Source) button on the right side panel or on the remote

control.

2 Audio (AUX) Cable

X Connect AUX IN (Audio) on the main unit to the AUDIO OUT jack of the Source Device using an

audio cable.

Y Select “AUX” mode by pressing (Source) button on the right side panel or on the remote

control.

ENG - 14

06 CONNECTING A USB

You can play music les located on USB storage devices through the Soundbar.

USB por t

DIGITAL AUDIO IN

HDMI IN

(OPTICAL)

USB (5V 0.5A)

HDMI OUT
(TV-ARC)

AUX IN

DC 24V

DC 24V

USB (5V 0.5A)

Display

USB

Micro USB t o

USB adap ter Cable

(not supplied)

1. Connect a Micro USB to USB adapter cable with a male USB 2.0 Micro USB plug (Type B) on one

end and a standard female 2.0 USB jack (Type A) on the other end to the micro USB jack on your
Soundbar.

• Micro USB to USB adapter Cable is sold separately. To purchase, contact a Samsung Service
Centre or Samsung Customer Care.

2. Connect your USB device to the female end of the adapter cable.

3. Press the (Source) button on the right side panel or on the remote control, and then select
“USB”.

4. “USB” appears in the display screen.

5. Play music les from the USB storage device through the Soundbar.

• The Soundbar automatically turns off (Auto Power Off) if no USB device has been connected for
more than 5 minutes.

ENG - 15

File Format Type Compatibility list

Extension Codec Sampling Rate Bit Rate

*.m p3 MPEG 1 Layer2 16KHz ~ 48KHz 80kbps~320kbps

MPEG 1 Layer3 16KHz ~ 48KHz 80kbps~320kbps

MPEG 2 Layer3 16KHz ~ 48KHz 80kbps~320kbps

MPEG 2.5 Layer3 16KHz ~ 48KHz 80kbps~320kbps

*.wma Wave_Format_MSAudio1 16KHz ~ 48KHz 56kbps~128kbps

Wave_Format_MSAudio2 16KHz ~ 48KHz 56kbps~128kbps

*.a ac AAC 16KHz ~ 96KHz 48kbps~320kbps

A A C-L C 16KHz ~ 96KHz

HE-AAC 24KHz ~ 96KHz

*.wav - 16KHz ~ 48KHz up to 3000kbps

*.o gg OGG 1.1.0 16KHz ~ 48KHz 50kbps~500kbps

*. ac FL AC 1.1.0, FLAC 1.2.1 16KHz ~ 96KHz up to 3000kbps

128kbps~192kbps

5.1ch 320kbp s

48kbps~64kbps

5.1ch 160kbp s

• If there are too many folders and les stored on the USB device, it may take the Soundbar some

time to access and play les.

ENG - 16

07 CONNECTING A MOBILE DEVICE

Connecting via Bluetooth

When a mobile device is connected using Bluetooth, you can hear stereo sound without the hassle of
cabling.

• You cannot connect more than one Bluetooth device at a time.

Bluetooth device

The initial connection

1. Press the (Source) button on the right side panel or on the remote control, and then select
“BT”.

2. Change “BT” to “BT PAIRING”.

• If “BT READY” appears, press and hold the (Source) button on the right side panel of the
Soundbar or on the remote control for more than 5 seconds to display “BT PAIRING”.

3. Select “[AV] Samsung Soundbar Mxxx M-Series ” from the list.

• When a Soundbar is connected to the Bluetooth device, “[Bluetooth Device Name] → “BT”
appears in the front display.

4. Play music les from the device, connected via Bluetooth, through the Soundbar.

If the device fails to connect

• If the previously connected Soundbar listing (e.g. “[AV] Samsung Soundbar Mxxx M-Series ”)

appears in the list, delete it.

• In “BT” mode, press and hold the (Source) button for more than 5 seconds on the right side
panel of the Soundbar or on the remote control to switch to “BT PAIRING” mode.
Then, select “[ AV] Samsung Soundbar Mxxx M-Series” from the Bluetooth device search list.

ENG - 17

What are the BT READY and BT PAIRING statuses?

• BT READY : In this mode, you can search for previously connected TVs or connect to the Soundbar
from a previously connected mobile device.

• BT PAIRING : In this mode, you can connect to a new device. (While in “BT” mode, press and hold the

(Source) button for more than 5 seconds on the right side of the Soundbar or on the remote

control.)

NOTES

• If asked for a PIN code when connecting a Bluetooth device, enter <0000>.

• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the
Soundbar and the Bluetooth device exceeds 10 meters.

• The Soundbar automatically turns off after 5 minutes in the Ready state.

• The Soundbar may not perform Bluetooth search or connection correctly under the following
circumstances:

– If there is a strong electrical eld around the Soundbar.
– If several Bluetooth devices are simultaneously paired with the Soundbar.
– If the Bluetooth device is turned off, not in place, or malfunctions.

• Electronic devices may cause radio interference. Devices that generate electromagnetic waves
must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc.

• The Soundbar supports SBC data (44.1kHz, 48kHz).

• Connect only to a Bluetooth device that supports the A2DP (AV) function.

• You cannot connect the Soundbar to a Bluetooth device that supports only the HF (Hands Free)
function.

• Once you have paired the Soundbar to a Bluetooth device, selecting “[ AV] Samsung Soundbar
Mxxx M-Series” from the device’s scanned devices list will automatically change the Soundbar to
“BT” mode.

– Available only if the Soundbar is listed among the Bluetooth device’s paired devices.

(The Bluetooth device and the Soundbar must have been previously paired at least once.)

• The Soundbar will appear in the Bluetooth device’s searched devices list only when the Soundbar is
displaying “BT READY”.

• Soundbar cannot be paired to another Bluetooth device, while using the Bluetooth function.

Bluetooth POWER On (Bluetooth POWER)

If a previously paired Bluetooth device tries to pair with the Soundbar when the Bluetooth POWER On
function is on and the Soundbar is turned off, the Soundbar turns on automatically.

1. Press the Bluetooth POWER button on the remote while the Soundbar is turned on.

2. “ON - BLUETOOTH POWER” appears on the Soundbar’s display.

ENG - 18

Disconnecting the Bluetooth device from a Soundbar

You can disconnect a Bluetooth device from the Soundbar. For instructions, see the Bluetooth device’s
user manual.

• The Soundbar will be disconnected.

• When the Soundbar is disconnected from the Bluetooth device, the Soundbar will display
“BT DISCONNECTED” on the front display.

Disconnecting the Soundbar from the Bluetooth device

Press the (Source) button on the right side panel or on the remote control, and then change to any
mode except “BT”.

• Disconnecting takes time because the Bluetooth device must receive a response from the
Soundbar. (Disconnection time may differ, depending on the Bluetooth device)

• When the Soundbar is disconnected from the Bluetooth device, the Soundbar will display
“BT DISCONNECTED” on the front display.

NOTES

• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the
Soundbar and the Bluetooth device exceeds 10 meters.

• The Soundbar automatically turns off after 5 minutes in the Ready state.

More About Bluetooth

Bluetooth is a technology that enables Bluetooth-compliant devices to interconnect easily with each
other using a short wireless connection.

• A Bluetooth device may cause noise or malfunction, depending on usage, if:

– A part of your body is in contact with the receiving/transmitting system of the Bluetooth

device or the Soundbar.
– It is subject to electrical variation from obstructions caused by a wall, corner, or ofce partition.
– It is exposed to electrical interference from same frequency-band devices including medical

equipment, microwave ovens, and wireless LANs.

• Pair the Soundbar with the Bluetooth device while they are close together.

• The further the distance between the Soundbar and Bluetooth device, the worse the quality is.
If the distance exceeds the Bluetooth operational range, the connection is lost.

• In poor reception areas, the Bluetooth connection may not work properly.

• The Bluetooth connection only works when it is close to the unit. The connection will be
automatically cut off if the Bluetooth device is out of range. Even within range, the sound quality
may be degraded by obstacles such as walls or doors.

• This wireless device may cause electric interference during its operation.

ENG - 19

Using the Samsung Audio Remote App

Installing the Samsung Audio Remote App

To control the Soundbar with your smart device and the Samsung Audio Remote app, download the
Samsung Audio Remote app from the Google Play store.

Market se arch : Samsung Au dio Remote

Launching the Samsung Audio Remote App

To launch and use the Samsung Audio Remote app, touch the Audio Remote icon on your smart device,
and then follow the directions on the screen.

Audio Remote

• The Samsung Audio Remote app is only compatible with Android mobile phones and mobile devices
running Android OS 3.0 or later.

ENG - 20

08 USING THE REMOTE CONTROL

Bluetooth

POWER

How to Use the Remote Control

󱂓

󱂔

󱂕

󱂖

Surround

SOUND

MODE

VOL WOOFER

SOUNDBAR

Bluetooth

POWER

󱂗

󱂘

󱂙

󱂚

󱂛

󱂜

󱂓

󱂔

Power

Sound Control

Turns the Soundbar on and off.

You can selec t from TREBLE, BASS, or AUDIO
SYNC.

• To control the volume of the treble or bass

sound, select TREBLE or BASS in Sound
Settings, and then adjus t the volume
between -6~+6 by using the Up/Down
buttons.

• Press and hold the (Sound Control)

button for about 5 seconds to adjust the
sound for each frequency band. 150Hz,
300Hz, 600Hz, 1.2KHz, 2.5KHz, 5KHz, and
10KHz are selectable (Left/Right) and each
can be adjusted to a setting between

-6 ~ +6 (Up/Down).

• If the video and audio between the TV and
your Soundbar are not synchronised, select
AUDIO SYNC in Sound Settings, and then
set audio delay bet ween 0~300
milliseconds by using the Up/Down
buttons. (Except “USB” mode)

• Audio Sync is only suppor ted in some
functions.

󱂕

Surround

Surround

The Surround Sound function adds depth and a sense of space to sound.
Each time you press this but ton, ON and OFF alternate.

• ON : Play sound over all the speakers.

• OFF : You can hear the sound of the original source channel from several speakers.

ENG - 21

󱂖

Bluetooth

POWER

SOUND

MODE

SOUND MODE

You can selec t the desired sound effect by choosing STANDARD, MUSIC, CLEAR VOICE,
SPORTS, or MOVIE.

Select the “STANDARD” mode if you want to enjoy the original sound.

• DRC (Dynamic Rang e Control)

Lets you apply dynamic range control to Dolby Digital tracks. If you press and hold the
SOUND MODE button while in standby mode, DRC (Dynamic Range Control) turns on
or off. With the DRC turned on, loud sound is reduced. (The sound may be distorted.)

󱂗

󱂘

Source

Play / Pau se

Press to select a source connected to the Soundbar.

• BT PAIRING mode
To turn on “BT PAIRING” mode in “ BT” mode, press and hold the (S ource) button
for more than 5 seconds. See page 17 for details.

• Auto Power Down Function
The unit turns off automatically in the following situations.

– D.IN / HDMI / BT / USB Mode : If there is no audio signal for 5 minutes.
– AUX Mode :

– If the Audio (AUX) Cable is disconnected for 5 minutes.
– If there is no KE Y input for 8 hours when the Audio (AUX) Cable is connec ted.

(Auto Power Down function can be turned off only in that case.)

– To turn off Auto Power Down function, while in “AUX” mode, press and hold the

p button for 5 seconds. “ON - AU TO POWER DOWN ” / “OFF - AUTO POWE R
DOWN” appears on the display.

Press the p button to pause a music le temporarily.
If you press the button again, the music le plays.

ENG - 22

󱂙

Up/Down/

Left/Right

Press the indicated areas to select Up/Down/Left/Right.

Press Up/Down/Left /Right on the button to select or set functions.

• Repeat

To use the Repeat function in “USB” mode, press the Up but ton.

• Music Skip
Press the Right button to select the next music le. Press the Left button to select

the previous music le.

• Anynet+ / Auto P ower Link
You can turn Anynet+ and Auto Power Link on or off.
Anynet+ and Auto Power Link are controlled by the Right and Left buttons
respe ctively.

– Anynet+ : If the Soundbar is connected to a Samsung TV through an HDMI cable,

you can control your Soundbar with a Samsung TV remote control.
Press and hold the Right but ton for 5 seconds to toggle Anynet+ ON and OFF.

– Auto Power Link : If the Soundbar is connected to your TV through a digital

optical cable, the Soundbar can automatically turn on when you turn on your TV.
Press and hold the Left button for 5 seconds to toggle Auto Power Link ON and
OFF.

– Anynet+ / Auto Power Link are set to ON by default.

󱂚

Bluetooth

POWER

Bluetooth

POWER

Press to turn the Bluetooth POWER function on and off.
When the Bluetooth POWER function is on, “ON - BLUETOOTH POWER” appears in the
Soundbar’s display.

• Bluetooth POWER function : If the Soundbar is in standby mode and the Bluetooth
POWER function is On, when you turn on a previously connected Bluetooth device,
the Soundbar automatically turns on and connects via Bluetooth to the device.

• If you press the Bluetooth P OWER button again to turn off the BT function,
“OFF-BLUETOOTH POWER” appears in the Soundbar ’s display.

• If the “D.IN” mode is on and the Soundbar is connected to a Samsung smart TV
released in 2017 or later, the Soundbar can be controlled with the T V remote control.
In this mode, you cannot turn off Bluetooth POWER.

ENG - 23

󱂛

Bluetooth

POWER

SOUNDBAR

SOUNDBAR

Surround

SOUND

MODE

Bluetooth

POWER

Surround

SOUND

MODE

Bluetooth

POWER

VOL

WOOFER

SOUNDBAR

Surround

SOUND

MODE

Bluetooth

POWER

VOL

WOOFER

SOUNDBAR

SOUNDBAR

SOUNDBAR

WOOFER

Surround

Bluetooth

POWER

SOUND

MODE

WOOFER

VOL

Surround

Bluetooth

POWER

SOUND

MODE

WOOFER

VOL

Push the button up or down to adjust the volume of the subwoofer to -12 or -6 to +6.
Pressing the but ton reverts the subwoofer volume to level 0.

󱂜

VOL

Surround

Bluetooth

POWER

SOUND

MODE

WOOFER

VOL

Surround

Bluetooth

POWER

SOUND

MODE

WOOFER

VOL

Push the button up or down to adjust the volume.

• Mute
Press the VOL but ton to mute the sound. Press it again to unmute the sound.

Adjusting the Soundbar volume with a TV remote control

Use the TV menu to set the TV speaker on a Samsung TV external speakers.
(For more information, see the TV’s user manual.)

• After installing the Soundbar, you can adjust the Soundbar’s volume using the IR remote control
that came with a Samsung TV. (If you do not want to use this function, when the Soundbar is on,
press and hold the Surround button for 5 seconds. “OFF-TV REMOTE” appears in the Soundbar’s
display and the function turns off.)
To adjust the volume using only the Samsung TV remote control, press and hold the Surround
button for more than 5 seconds until “SAMSUNG-TV REMOTE” appears in the Soundbar display.

– Each time the Surround button is held for 5 seconds, the mode switches in the following order:

“SAMSUNG-TV REMOTE” (Default mode) → “OFF-TV REMOTE” → “ALL-TV REMOTE”.

• To adjust the Soundbar volume with the remote control that came with a TV made by a third party
manufacturer, turn the Soundbar on, press and hold the Surround button for 5 seconds
(“OFF-TV REMOTE” appears on the Soundbar’s display), release the Surround button, and then
press and hold the Surround button again for more than 5 seconds. (“ALL-TV REMOTE” appears on
the Soundbar’s display.)

– This function may not be available, depending on the remote control.
– Manufacturers supporting this function:

VIZIO, LG, Sony, Sharp, PHILIPS, PANASONIC, TOSHIBA, GRUNDIG, Hisense, RCA

ENG - 24

Using the Hidden Buttons

Bluetooth

POWER

Bluetooth

POWER

Hidden Button

Remote Control Button Function

Surround TV remote control On/Off page 24

(Source)

p (Play / Pause)

VOL ID SET (Standby) page 7

Left Auto Power Link ON/OFF page 10

Right Anynet+ ON/OFF page 23

(Sound Control)

SOUND MODE DRC ON/OFF (Standby) page 22

Auto Power Down On/Off (AUX mode) page 22

BT Paring page 17

Initialise (Standby) page 30

7 Band EQ page 21

Reference page

Outputspecicationsforthedifferentsoundeffectmodes

Output

Surround

Surround

Effect Input

2.0 ch

ON

5.1 ch 2.1 ch 4.1 ch

Except Wireless Rear

Spea ker Kit

2.1 ch 4.1 ch

Include Wireless Rear

Spea ker Kit

SOUND

MODE

SOUND MODE

STANDARD

2.0 ch

5.1 ch 2.1 ch 4.1 ch

2.0 ch

MUSIC

5.1 ch 2.1 ch 4.1 ch

2.0 ch

CLEAR VOICE

5.1 ch 2.1 ch 4.1 ch

2.0 ch

SPORTS

5.1 ch 2.1 ch 4.1 ch

2.0 ch

MOVIE

5.1 ch 2.1 ch 4.1 ch

2.1 ch 4.1 ch

2.1 ch 4.1 ch

2.1 ch 4.1 ch

2.1 ch 4.1 ch

2.1 ch 4.1 ch

• Samsung Wireless Rear Speaker Kit can be purchased separately. To purchase a Kit, contact the
vendor you purchased the Soundbar from.

ENG - 25

09 INSTALLING THE WALL MOUNT

Installation Precautions

• Install on a vertical wall only.

• Do not install in a place with high temperature or humidity.

• Verify whether the wall is strong enough to support the product’s weight. If not, reinforce the wall
or choose another installation point.

• Purchase and use the xing screws or anchors appropriate for the kind of wall you have (plaster

board, iron board, wood, etc.). If possible, x the support screws into wall studs.

• Purchase wall mounting screws according to the type and thickness of the wall you want to mount
the Soundbar on.

– Diameter: M5
– Length: 35 mm or longer recommended.

• Connect cables from the unit to external devices before you install the Soundbar on the wall.

• Make sure the unit is turned off and unplugged before you install it. Otherwise, it may cause an
electric shock.

Wallmount Components

ENG - 26

A-TYPE : 616mm
B-TYPE : 360mm

A B B A

Holder-Screw (2 EA) Screw (2E A) Bracket-Wall Mount L Bracket-Wall Mount R

CENTER LINE

Wall Mount Guide

1. Place the Wall Mount Guide against the wall

B

CENTER LINE

surface.

• The Wall Mount Guide must be level.

• If your TV is mounted on the wall, install
the Soundbar at least 5 cm below the TV.

5 cm or more

2. Align the Paper Template’s Centre Line with

the centre of your TV (if you are mounting

the Soundbar below your TV), and then x

the Wall Mount Guide to the wall using tape.

• If you are not mounting below a TV, place
the Centre Line in the centre of the
installation area.

3. Push a pen tip or sharpened pencil tip
through the centre of the B-TYPE images on
each end of the Guide to mark the holes for
the supporting screws, and then remove the
Wall Mount Guide.

A B B A

CENTER LINE

A-TYPE : 616mm
B-TYPE : 360mm

4. Using an appropriately sized drill bit, drill a
hole in the wall at each marking.

• If the markings do not correspond to the
positions of studs, make sure you insert
appropriate anchors or mollies into the
holes before you insert the support
screws. If you use anchors or mollies,
make sure the holes you drill are large
enough for the anchors or mollies you
use.

5. Push a screw (not supplied) through each
Holder-Screw, and then screw each screw

rmly into a support screw hole.

A B B A

CENTER LINE

A-TYPE : 616mm
B-TYPE : 360mm

Centre Line

ENG - 27

6. Use the two Screws (M4 x L12) to attach both
Bracket-Wall Mount L and R to the

Soundbar’s bottom.

For a proper t, make sure to align the

bumps on the Soundbar to the holes on the
brackets.

• When assembling, make sure the hanger

part of the Bracket-Wall Mounts are
located behind the rear of the Soundbar.

Rear of S oundbar

• The left and right mounts are different
shapes. Make sure to position them

correc tly.

Wall Mount R Wall Mount L

7. Install the Soundbar with the attached
Bracket-Wall Mounts by hanging the
Bracket-Wall Mounts on the Holder-Screws

on the wall.

• Slightly tilt the Soundbar to insert both

Holder-Screw heads into Bracket-Wall
Mount holes. Push the Soundbar in the

direction of the arrow to make sure both sides

are rmly xed.

Right end o f Soundbar

ENG - 28

Detaching the Soundbar from the Wall

1. To separate the Soundbar from the wall

mount, push it in the direction of arrow, tilt it
up slightly, and then pull it away from the
wall as shown.

• Do not hang onto the installed unit and avoid
striking or dropping the unit.

• Secure the unit rmly to the wall so that it
does not fall off. If the unit falls off, it may
cause an injury or damage the product.

• When the unit is installed on a wall, please
make sure that children do not pull any of the
connecting cables, as this may cause it to fall.

• For the optimal performance of a wall mount
installation, install the speaker system at
least 5 cm below the TV, if the TV is mounted
on the wall.

• For your safety, if you do not mount the unit

on the wall, install it on a secure, at surface

where it is unlikely to fall.

10 SOFTWARE

UPDATE

Samsung may offer updates for the Soundbar’s

systemrmwareinthefuture.

USB por t

DIGITAL AUDIO IN

HDMI IN

(OPTICAL)

DC 24V

DC 24V

USB (5V 0.5A)

HDMI OUT
(TV-ARC)

AUX IN

USB (5V 0.5A)

Micro USB t o

USB adap ter Cable

(not supplied)

If an update is offered, you can update the

rmware by connecting a USB device with the
rmware update stored on it to the USB port on

your Soundbar.
For more information about how to download

update les, go to the Samsung Electronics

website at (www.samsung.com  Support).
Then, enter or select the model of your Soundbar,
select Software & Apps, and then Downloads.
The option name can vary.

ENG - 29

Updating Procedure

If UPDATE is not displayed

1. Connect a Micro USB to USB adapter cable

with a male USB 2.0 Micro USB plug (Type B)
on one end and a standard female 2.0 USB
jack (Type A) on the other end to the micro
USB jack on your Soundbar.

• The Micro USB to USB adapter cable is
sold separately. To purchase, contact a
Samsung Service Centre or Samsung
Customer Care.

2. Follow the steps below to download the

product software:
Go to the Samsung website at
(samsung.com)  search for the model
name - select the customer suppor t option
(the option name is subject to change)

3. Save the downloaded software to a USB

stick and select “Extract Here” to unzip the
folder.

4. Turn off the Soundbar and connect the USB

stick containing the software update to the
female port on a Micro USB adapter cable.
Connect the cable to the USB port on the
Soundbar.

5. Turn on the Soundbar. Within 3 minutes,
“UPDATE” is displayed and updating begins.

6. When the update nishes, the Soundbar

turns off. Press the p button on the remote
control for 5 seconds. “INIT” appears on the
display and then the Soundbar turns off.
The update is complete.

• This product has a DUAL BOOT function.

If the rmware fails to update, you can
update the rmware again.

1. Turn off the Soundbar, disconnect and then

reconnect the USB storage device that

contains the update les to the Soundbar’s

USB port.

2. Disconnect the Soundbar’s power cord,

reconnect it, and then turn on the Soundbar.

• Updating rmware may not work

properly if audio les supported by the

Soundbar are stored in the USB storage
device.

• Do not disconnect the power or remove
the USB device while updates are being
applied. The main unit will turn off
automatically after completing the

rmware update.

• After update is completed, the user setup
in Soundbar is initialised. We recommend
you write down your settings so that you
can easily reset them after the update.

Note that updating rmware resets the

subwoofer connection too.
If the connection to the subwoofer is not
re-established automatically after the
update, refer to page 6.
If the software update fails, check if the
USB stick is defective.

• Mac OS users should use MS-DOS (FAT)
as the USB format.

• Updating via USB may not be available,
depending on the USB storage device
manufacturer.

ENG - 30

11 TROUBLESHOOTING

Before seeking assistance, check the following.

The unit will not turn on.

Is the power cord plugged into the outlet?

; Connect the power plug to the outlet.

A function does not work when the button is pressed.

Is there static electricity in the air?

; Disconnect the power plug and connect it again.

Sound dropouts occur in BT mode.

; See the Bluetooth connection sections on pages 11 and 17.

Sound is not produced.

Is the Mute function on?

; Press the VOL button to cancel the function.

Is the volume set to minimum?

; Adjust the Volume.

The remote control does not work.

Are the batteries drained?

; Replace with new batteries.

Is the distance between the remote control and Soundbar main unit too far?

; Move the remote control closer to the Soundbar main unit.

The red LED on the subwoofer blinks and the subwoofer is not producing sound.

This issue can occur if the subwoofer is not connected to the Soundbar main unit.

; Try to connect your subwoofer again. (See page 6.)

The subwoofer drones and vibrates noticeably.

Try to adjust the vibration of your subwoofer.

; Push the WOOFER button on your remote control up or down to adjust the subwoofer volume.

(between -12, -6 ~ +6).

ENG - 31

12 LICENCE

13 OPEN SOURCE

LICENCE NOTICE

Manufactured under licence from Dolby
Laboratories. Dolby, Dolby Audio and the
double-D symbol are trademarks of Dolby
Laboratories.

For DTS patents, see http://patents.dts.com.
Manufactured under licence from DTS
Licencing Limited. DTS, the Symbol, & DTS and
the Symbol together are registered
trademarks, and DTS 2.0 Channel is a
trademark of DTS, Inc. © DTS, Inc.
All Rights Reserved.

The terms HDMI and HDMI High-Denition

Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI
Licencing LLC in the United States and other
countries.

To send inquiries and requests regarding open
sources, contact Samsung via Email
([e-mail]).

14 IMPORTANT

NOTES ABOUT
SERVICE

• Figures and illustrations in this User Manual
are provided for reference only and may differ
from actual product appearance.

• An administration fee may be charged if
either
(a) an engineer is called out at your request

and there is no defect with the product (i.e.
where the user manual has not been read).

(b) you bring the unit to a repair centre and

there is no defect with the product (i.e.
where the user manual has not been read).

• You will be informed of the administration fee
amount before a technician visits.

ENG - 32

15 SPECIFICATIONS AND GUIDE

Specications

USB

Weight

GENERAL

AMPLIFIER

Supported play formats

(DTS 2.0 sound is played in DTS format.)

Dimensions
(W x H x D)

Operating Temperature Range

Operating Humidity Range

Rated Output
power

Soundbar Main Unit

Subwoofer (PS-WM30)

Soundbar Main Unit

Subwoofer (PS-WM30)

Soundbar Main Unit

Subwoofer (PS-WM30)

5V/ 0.5A

2.0 kg

7.2 kg

908.5 x 53.5 x 70.5 mm

200.0 x 392.0 x 378.0 mm

+5°C to +35°C

10 % ~ 75 %

40W x 4, 6 ohm

160W, 3 ohm

LPCM 2ch, Dolby Audio™
(supporting Dolby® Digital), DTS

NOTES

• Samsung Electronics Co., Ltd reserves the right to change the specications without notice.

• Weight and dimensions are approximate.

• For more information about the power supply and power consumption, refer to the label attached
to the product. (Label : Bottom of the Soundbar Main Unit)

Overall Standby Power Consumption (W)

Bluetooth Port deactivation method

2.9W

Press the “Bluetooth POWER” button on the
remote control when “BT” mode.

Wireless Models (including the frequency of 5.15GHz-5.35GHz)

• Hereby, Samsung Electronics, declares that this equipment is in compliance
with the essential requirements and other relevant provisions of Directive
1999/5/EC.
The original Declaration of Conformity may be found at http://www.samsung.com,
go to Support > Search Product Support and enter the model name.
This equipment may be operated in all EU countries.
This equipment may only be used indoors.

ENG - 33

Wireless Models (excluding the frequency of 5.15GHz-5.35GHz)

• Hereby, Samsung Electronics, declares that this equipment is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.
The original Declaration of Conformity may be found at http://www.samsung.com,
go to Support > Search Product Support and enter the model name.
This equipment may be operated in all EU countries.

[Correct disposal of bat teries in this product]

(Applicable in countries with separate collec tion systems)

This marking on the battery, manual or packaging indicates that the batteries in this product should not be
disposed of with other household waste at the end of their working life. Where marked, the chemical
symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference
levels in EC Directive 2006/66.
If batteries are not properly disposed of, these substances can cause harm to human health or the
environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of
waste and recycle them through your local, free battery return system.

Correc t Disposal of This Produc t

(Waste Electrical & Electronic Equipment)

(Applicable in countries with separate collec tion systems)

This marking on the product, accessories or literature indicates that the product and its electronic
accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the
end of their working life. To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate these items from other types of waste and recycle them responsibly to
promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local

government ofce, for details of where and how they can take these items for environmentally safe

recycling.
Business users should contac t their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

For information on Samsung’s environmental commitments and product specic regulatory obligations

e.g. REACH visit: samsung.com/uk/aboutsamsung/samsungelectronics/corporatecitizenship/data_corner.

html

ENG - 34

UNITED KINGDOM

EIRE

EIRE

EIRE

This Samsung product is warranted for the period of
twelve (12) months from the original date of purchase,
against defective materials and workmanship. In the
event that warranty service is required, you should return
the product to the retailer from whom it was purchased.
However, Samsung Authorised Dealers and Authorised
Service Centres in other EC Countries will comply with
the warranty on the terms issued to purchasers in the

country concerned. In case of difculty, details of our

Authorised Service Centres are available from:

Samsung Electronics U.K. Ltd
Samsung Customer Support Centre
Selectapost38,Shefeld,S973FJ
United Kingdom

United Kingdom
Tel : 0330 SAMSUNG (7267864)
www.samsung.com/uk/support

EIRE
Tel : [phone]
www.samsung.com/ie/support

@ WARRANTY CONDITIONS

1. The warranty is only valid if, when warranty

service is required, the warranty card is fully
and properly completed and is presented with

the original invoice or sales slip or conrmation,

and the serial number on the product has not
been defaced.

2. Samsung’s obligations are limited to the repair

or, at its discretion, replacement of the product
or the defective part.

3. Warranty repairs must be carried out by

Authorised Samsung Dealers or Authorised
Service Centres. No re-imbursement will be
made for repairs carried out by non Samsung
Dealers and, any such repair work and damage
to the products caused by such repair work will
not be covered by this warranty.

4. This product is not considered to be defective

in materials nor workmanship by reason that it
requires adaptation in order to conform to
national or local technical or safety standards
in force in any Countr y other than the one for
which the product was originally designed and
anufactured.
re-imbursement will be made for such adaptation
nor any damage which may result

5. This warranty covers none of the following:

a)

Periodic check ups, maintenance and repair or

replacement of parts due to normal wear and
tear.

b) Cost relating to transport, removal or

installation of the product.

c) Misuse, including the faiure to use this

product for its normal purposes or incorrect
installation.

d) Damage caused by Lightning, Water, Fire,

Acts of God, War, Public Disturbances,
incorrect mains voltage, improper
ventilation or any other cause beyond the
control of Samsung.

6. This warranty is valid for any person who

legally acquired possession of the product
during the warranty period.

7. The consumers statutory rights in any

applicable national legislation whether
against the retailer arising from the
purchase contract or otherwise are not
affected by this warranty. Unless there is
national legislation to the contrary, the
rights under this warranty are the
consumers sole rights and Samsung, its
subsidiaries and distributors shall not be
liable for indirect or consequential loss or
any damage to records, compact discs,
videos or audio taper or any other related
equipment or material.

This warranty will not cover, and no

.

SAMSUNG ELECTRONICS (U.K.) LTD.

© 2017 Sam sung Electronics Co. , Ltd. All rights reser ved.

Contact SAMSUNG WORLD WIDE

If you have any questions or co mments rela ting to Samsung pr oducts, pl ease contac t the SAMSUNG customer

care Centre.

Country Contact Centre

`

Europe

U.K 0330 SAM SUNG (726 7864)

EIRE 0818 717100

0180 6 SA MSUNG bzw.

GERMANY

FRANCE 01 48 63 0 0 00

ITALIA 800-SAMSUNG (800.7267864)

SPAIN 349021 72678

PORTUGAL 808 20 7267

LUXEMBURG 261 03 710

NETHERLANDS

BELGIUM 02-20 1-24-18

NO RWAY 815 5 6480

DENMARK 70 70 19 70

FINLAND 030- 6227 515

SWEDEN 0 771 72 6 7864 (07 71-SAMS UNG)

POLAND

HUNGARY

0180 6 7 267864*
(*0,20 € /Anruf aus dem d t. Festn etz,
aus dem M obilfunk max . 0,60 €/
Anruf)

0900 -SAMSUN G (0900-7 267864)
(€ 0,10/ Min)

801-17 2-678* lub [phone] *

* (koszt po łączenia we dług taryf y

operatora)

0680SAMSUNG (0680-726-786)
0680PREMIUM (0680-773-648)



www.samsung .com/uk/
support

www.samsung.com/ie/
support

www.samsung.com/de/
support

www.samsung.com/fr/
support

www.samsung.com/it/
support

www.samsung.com/es/
support

www.samsung.com/pt/
support

www.samsung.com/be_fr/
support

www.samsung.com/nl/
support

www.samsung.com/be/
suppor t (Dutch)
www.samsung.com/be_fr/
support (French)

www.samsung.com/no/
support

www.samsung .com/dk/
support

www.samsung.com//

support

www.samsung.com/se/
support

www.samsung.com/pl/
support

www.samsung.com/hu/
support

Web Site

Country Contact Centre

AUSTRI A

SWITZERLAND 0800 726 78 6 4 (0800-S AMSUNG)

CZECH 800 - S AMSUNG (800 -726786)

SLOVA KIA 0800 - SAM SUNG (0800 -726 786)

CROATIA 072 7 26 786

BOSNIA 055 2 33 999

MONTENEGRO 02 0 405 888

SLOVENIA 0 80 697 267 (bre zplačna štev ilka) ww w.samsung.com/si

SERBIA 011 321 6 899

BULGARIA

ROMANIA

CYPRUS

GREECE

LITHUANIA 8-800-77777

LAT VIA 8000-7267

ESTONIA 80 0-7267

0800-SAMSUNG (0800-7267864)
[Only for P remium HA] 080 0-3666 61
[Only for De alers] 0810 -112233

*3000 Цен а в мрежа та
0800 111 31 , Без платна тел ефонна
линия

*8000 ( apel in retea)
080 08-726 -78-6 4
(0800 8-SAMSUNG )
Apel GRATUIT

8009 4 000 only from l andline, tol l
free

80111- SAMSUNG (80 111 726 786 4)
only from l and line (+30) 210
6897691 from mobile and land line



Web Site

www.samsung.com/at/
support

www.samsung.com/ch/
suppo rt (Germa n)
www.samsung.com/ch_fr/
support (French)

www.samsung.com/cz/
support

www.samsung.com/sk/
support

www.samsung.com/hr/
support

www.samsung.com/
support

www.samsung.com/
support

www.samsung.com/rs/
support

www.samsung.com/bg/
support

www.samsung.com/ro/
support

www.samsung .com/gr/
support

www.samsung.com/lt/
support

www.samsung.com/lv/
support

www.samsung.com/ee/
support