Samsung HT-H5550W, HT-H5500W User Manual

HT-H5500 HT-H5500W HT-H5530 HT-H5550 HT-H5550W

5.1CH Blu-ray™

Home Entertainment System

user manual

imagine the possibilities

Thank you for purchasing this Samsung product. To receive more complete service, please register your product at

www.samsung.com/register

HT-H5500_00W_30_50_50W-ENG_0402.indd 1HT-H5500_00W_30_50_50W-ENG_0402.indd 1 2014-04-02  1:07:152014-04-02  1:07:15

Safety Information

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE THE COVER (OR BACK). THERE ARE NO USER

SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO

• The slots and openings in the cabinet and in the back or bottom are provided for necessary ventilation. To ensure reliable operation of this apparatus, and to protect it from overheating, these slots and openings must never be blocked or covered.

- Do not place this apparatus in a confined space, such as a bookcase, or built-in cabinet, unless proper ventilation is provided.

- Do not place this apparatus near or over a radiator or heat register, or where it is exposed to direct sunlight.

- Do not place vessels (vases etc.) containing water on this apparatus. A water spill can cause a fire or electric shock.

• Do not expose this apparatus to rain or place it near water (near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc.). If this apparatus accidentally gets wet, unplug it and contact an authorized dealer immediately.

• This apparatus uses batteries. In your community, there might be environmental regulations that require you to dispose of these batteries properly. Please contact your local authorities for disposal or recycling information.

• Do not overload wall outlets, extension cords or adaptors beyond their capacity, since this can result in fire or electric shock.

• Route power-supply cords so that they are not likely to be walked on or pinched by items placed on or against them. Pay particular attention to cords at the plug end, at wall outlets, and the point where they exit from the apparatus.

• To protect this apparatus from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the set due to lightning and power line surges.

• Before connecting the AC power cord to the DC adaptor outlet, make sure the voltage designation of the DC adaptor corresponds to the local electrical supply.

• Never insert anything metallic into the open parts of this apparatus. Doing so may create a danger of electric shock.

QUALIFIED PERSONNEL.

• To avoid electric shock, never touch the inside of this

• Make sure to plug the power cord in until it is firmly

• If this apparatus does not operate normally - in

• Maintenance of Cabinet.

• Be sure to pull the power plug out of the outlet if the

• Contact an authorized service centre for information

• Use only a properly grounded plug and wall outlet.

• To turn this apparatus off completely, you must

• Do not allow children to hang on the product.

This symbol indicates that high voltage is present inside. It is dangerous to make any kind of contact with any internal part of this product.

This symbol indicates that important literature concerning operation and maintenance has been included with this product.

apparatus. Only a qualified technician should open this apparatus.

seated. When unplugging the power cord from a wall outlet, always pull on the power cord's plug. Never unplug by pulling on the power cord. Do not touch the power cord with wet hands.

particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service centre.

- Before connecting other components to this product, be sure to turn them off.

- If you move your product suddenly from a cold place to a warm place, condensation may occur on the operating parts and lens and cause abnormal disc playback. If this occurs, unplug the product, wait for two hours, and then connect the plug to the power outlet. Then, insert the disc, and try to play back again.

product is to remain unused or if you are leaving the house for an extended period of time (especially when children, elderly, or disabled people will be left alone in the house).

- Accumulated dust can cause an electric shock, an electric leakage, or a fire by causing the power cord to generate sparks and heat or the insulation to deteriorate.

if you intend to install your product in a location with heavy dust, high or low temperatures, high humidity, chemical substances, or where it will operate 24 hours a day such as in an airport, a train station, etc. Failing to do so may lead to serious damage of your product.

- An improper ground may cause electric shock or equipment damage. (Class l Equipment only.)

disconnect it from the wall outlet. Consequently, the wall outlet and power plug must be readily accessible at all times.

2 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 2HT-H5500_00W_30_50_50W-ENG_0402.indd 2 2014-04-02  1:07:292014-04-02  1:07:29

• Store the accessories (battery, etc.) in a location safely out of the reach of children.

• Do not install the product in an unstable location such as a shaky self, a slanted floor, or a location exposed to vibration.

• Do not drop or strike the product. If the product is damaged, disconnect the power cord and contact a service centre.

• To clean this apparatus, unplug the power cord from the wall outlet and wipe the product using a soft, dry cloth. Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air fresheners, lubricants, or detergent. These chemicals can damage the appearance of the product or erase the printing on the product.

• Do not expose this apparatus to dripping or splashing. Do not put objects filled with liquids, such as vases on the apparatus.

• Do not dispose of batteries in a fire.

• Do not plug multiple electric devices into the same wall

socket. Overloading a socket can cause it to overheat, resulting in a fire.

• There is danger of an explosion if you replace the batteries used in the remote with the wrong type of battery. Replace only with the same or equivalent type.

WARNING :

• TO PREVENT THE SPREAD OF FIRE,

KEEP CANDLES AND OTHER ITEMS WITH OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES.

CLASS 1 LASER PRODUCT

This product is classified as a CLASS 1 LASER product. Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

CAUTION :

• INVISIBLE LASER RADIATION WHEN OPEN AND

INTERLOCKS DEFEATED, AVOID EXPOSURE TO BEAM.

CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT PRODUCTO LÁSER CLASE 1

3D Precautions

IMPORTANT HEALTH AND SAFETY INFORMATION FOR 3D PICTURES. Read and understand the following safety information before using the 3D function.

• Some viewers may experience discomfort while viewing 3D TV such as dizziness, nausea, and headaches. If you experience any such symptom, stop viewing 3D TV, remove the 3D Active Glasses, and rest.

• Watching 3D images for an extended period of time may cause eye strain. If you feel eye strain, stop viewing 3D TV, remove your 3D Active Glasses, and rest.

• A responsible adult should frequently check on children who are using the 3D function. If there are any reports of tired eyes, headaches, dizziness, or nausea, have the child stop viewing 3D TV and rest.

• Do not use the 3D Active Glasses for other purposes (such as general eyeglasses, sunglasses, protective goggles, etc.)

• Do not use the 3D function or 3D Active Glasses while walking or moving around. Using the 3D function or 3D Active Glasses while moving around may cause you to bump into objects, trip, and/or fall, and cause serious injury.

• If you want to enjoy 3D content, connect a 3D device (3D compliant AV receiver or TV) to the product’s HDMI OUT port using a high-speed HDMI cable. Put on 3D glasses before playing the 3D content.

• The product outputs 3D signals only through an HDMI cable connected to the HDMI OUT port.

• The video resolution in 3D play mode is fixed to the resolution of the original 3D video. You can not change the resolution.

• Some functions such as BD Wise, screen size adjustment, and resolution adjustment may not operate properly in 3D play mode.

• You must use a high-speed HDMI cable for proper output of the 3D signal.

• Stay at least three times the width of the screen from the TV when watching 3D images. For example, if you have a 46 inch screen, stay 3.5 meters from the screen.

• Place the 3D video screen at eye level for the best 3D picture.

• When the product is connected to some 3D devices, the 3D effect may not function properly.

• This product does not convert 2D content into 3D.

• "Blu-ray 3D" and "Blu-ray 3D" logo are trademarks of

the Blu-ray Disc Association.

Safety Information

3 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 3HT-H5500_00W_30_50_50W-ENG_0402.indd 3 2014-04-02  1:07:292014-04-02  1:07:29

Contents

GETTING STARTED

5 Accessories 5 Speaker Components 7 Front Panel 7 Rear Panel 8 Remote Control

CONNECTIONS

9 Connecting the Speakers 12 Attaching the Toroidal Ferrite Core to the Power

Cord of the Wireless Receiver Module (SWA-

6000)

13 Connecting to a TV and External Devices 14 Connecting to a Network Router

SETTINGS

15 The Initial Settings Procedure 16 The Home Screen at a Glance 16 Accessing the Settings Screen 17 Settings Menu Functions 20 Network Setup 22 Wi-Fi Direct 23 Upgrading Software 25 Setting Up DLNA

PLAYING CONTENT

26 Switching the Source Device 26 Playing Commercial Discs 26 Playing a Disc with User Recorded Content 27 Playing Files on a USB Device 28 Controlling Video Playback 29 Playing a Pre-Recorded Commercial Audio Disc 30 Controlling Music Playback 31 Playing Photo Contents 32 Listening to the Radio 33 Using Bluetooth 36 Using the Special Effects Remote Control

Buttons

NETWORK SERVICES

37 Using BD-LIVE™ 37 Using DLNA 37 Apps 38 Using Opera TV Store 39 Screen Mirroring

APPENDIX

40 Additional Information 41 Disk and Format Compatibility 46 Troubleshooting 49 Specifications 51 Licences

Wiring the Main Power Supply Plug (UK Only)

IMPORTANT NOTICE : The mains lead on this equipment is supplied with a moulded plug incorporating a fuse.

The value of the fuse is indicated on the pin face of the plug and if it requires replacing, a fuse approved to BS1362 of the same rating must be used. Never use the plug with the fuse cover removed. If the cover is detachable and a replacement is required, it must be of the same colour as the fuse fitted in the plug. Replacement covers are available from your dealer. If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should obtain a suitable safety approved extension lead or consult your dealer for assistance. However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect the plug to a mains socket as there is a risk of shock hazard from the bared flexible cord. Never attempt to insert bare wires directly into a mains socket. A plug and fuse must be used at all times.

IMPORTANT : The wires in the mains lead are coloured in accordance with the following code:– BLUE = NEUTRAL BROWN = LIVE As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows:–The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.

IMPORTANT : DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH LETTER E OR BY THE EARTH SYMBOL

, OR COLOURED GREEN OR GREEN AND YELLOW.

4 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 4HT-H5500_00W_30_50_50W-ENG_0402.indd 4 2014-04-02  1:07:302014-04-02  1:07:30

Getting Started

Figures and illustrations in this User Manual are provided for reference only and may differ from actual

product appearance.

An administration fee may be charged if either

a. an engineer is called out at your request and there is no defect in the product (i.e. where you have

failed to read this user manual)

b. you bring the unit to a repair centre and there is no defect in the product (i.e. where you have failed

to read this user manual).

 The amount of such administration charge will be advised to you before any work or home visit is

carried out.

Check the box for the accessories and speaker components listed or shown below.

Accessories

• Remote Control • User Manual • Batteries

HT-H5500W/HT-H5550W only

(For Power cord)

Power Cable FM Antenna Toroidal Ferrite Core

Speaker Components

Getting Started

HT-H5500/HT-H5500W

HT-H5500W only

Centre

Front x 2 Surround x 2

Speaker Cable

x 6 Subwoofer

Wireless Receiver

Module (SWA-6000)

5 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 5HT-H5500_00W_30_50_50W-ENG_0402.indd 5 2014-04-02  1:07:302014-04-02  1:07:30

Getting Started

HT-H5530

Screw (5x20) x 8

Front x 2 Stand x 2 Surround x 2

HT-H5550/HT-H5550W

Screw (5x20) x 16

Centre

Speaker Cable

Centre

Stand Base x 2

x 6 Subwoofer

Stand Base x 4

HT-H5550W only

Front x 2

Surround x 2

Stand x 4 Subwoofer

Speaker Cable

Wireless Receiver

x 6

Module (SWA-6000)

6 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 6HT-H5500_00W_30_50_50W-ENG_0402.indd 6 2014-04-02  1:07:322014-04-02  1:07:32

Front Panel

5V 0.5A

SURROUND

NFC

DISPLAY ICONS

FUNCTION STOP PLAY/PAUSE

OPEN/ CLOSE

VOLUME CONTROL

DISPLAY

POWER

Getting Started

DISC TRAY

When the product is on, do not let children touch the product's surface. It will be hot.

✎

To upgrade the product's software through the USB jack, you must use a USB flash drive.

✎

When the product displays the Blu-ray Disc menu, you cannot start the movie by pressing the /6 button

✎

on the product or the remote. To play the movie, you must select Play Movie or Start in the disc menu, and then press the E button.

If you are using the Internet or are playing content from a USB device on your TV through the home cinema,

✎

you cannot select the BD/DVD mode with the Internet or stop the content you are playing on the TV, and then select the BD/DVD mode.

To use the NFC function, tag the compatible Bluetooth source device to the on the top of the product

✎

(See page 35).

FUNCTION button. To select the BD/DVD mode, exit the

USBREMOTE CONTROL SENSOR

Rear Panel

* In case of HT-H5500/HT-H5530/HT-H5550

COOLING FAN

POWER CORD LAN TERMINALEXTERNAL DIGITAL

* Connecting the FM Antenna

1. Connect the supplied FM antenna to the FM ANT Jack.

2. Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a

wall or other rigid surface.

Maintain a minimum of 10 cm of clear space on all sides of the home cinema to ensure adequate ventilation.

✎

Do not obstruct the cooling fan or ventilation holes. This product does not receive AM broadcasts.

✎

SPEAKER OUTPUT

CONNECTORS

AUX IN

* FM ANTENNA

HDMI OUT

AUDIO IN (OPTICAL)

7 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 7HT-H5500_00W_30_50_50W-ENG_0402.indd 7 2014-04-02  1:07:332014-04-02  1:07:33

Getting Started

Remote Control

Tour of the Remote Control

Turn the product on and off.

Adjust the volume.

Press numeric buttons to operate

options.

Press to view the disc menu.

VOLUME

RDS DISPLAY TA

DISC MENU

PTY - PTY SEARCH PTY +

56 89

Press to skip backwards or forwards.

Press to play a disc or files.

Press to stop a disc or files.

SUBTITLE HOME

Selects the disc subtitle language.

Press to move to the Home screen.

TOOLS

Press to use the Tools menu.

Select on-screen menu items

and change menu values.

Return to the previous menu.

These buttons are used both for

menus on the product and also

RETURN

ABCD

DPS/EQTV SOUND

several Blu-ray Disc functions.

Press to direct audio signal to home

cinema speaker or TV speaker.

(See page 36)

Select the desired DSP/EQ audio

mode.

Installing batteries in the Remote Control

Make sure to match the "+" and "–" ends of the batteries with

✎

the diagram inside the compartment. Assuming typical usage, the batteries last for about one year.

✎

The remote control can be used up to approximately 7 meters

✎

from the product in a straight line.

TITLE MENU

TUNER

MEMORY

TUNING

DOWN

FUNCTION

MUTE

POPUP

REPEAT

INFO

EXIT

MO/ST

Battery size: AAA

Press to select Home Cinema's mode. (BD/DVD, D. IN, AUX, etc.).

To open and close the disc tray.

Cut off the sound temporarily.

Use the RDS function to receive FM stations.

Use to enter the Popup menu/ Title menu.

Press to search backwards or forwards. Press to pause playing.

Allows you to repeat a title, chapter, track or disc.

Use to display the playback information when playing a Blu-ray/DVD disc or files.

Press to exit the menu. Use to set a preset radio frequency.

Select MONO or STEREO for radio broadcasts.

Search for active FM stations and to change channels.

8 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 8HT-H5500_00W_30_50_50W-ENG_0402.indd 8 2014-04-02  1:07:352014-04-02  1:07:35

Connections

This section describes various methods of connecting the product to other external components. Before moving or installing the product, be sure to turn off the power and disconnect the power cord.

Connecting the Speakers

Subwoofer

Front (L)

Surround (L)

* HT-H5500/HT-H5530/HT-H5550

Position of the product

Place it on a stand or cabinet shelf, or under the TV stand.

Selecting the Listening Position

The listening position should be located about 2.5 to 3 times the TV's screen size away from the TV. For example, if you have a 46 inch screen, locate the listening position 2.92 to 3.50 meters from the screen.

Front Speakers

Centre Speaker

Surround Speakers

Centre

Product

Front (R)

Surround (R)

Place these speakers in front of your listening position, facing inwards (about 45°) toward you. Place the front speakers so that their tweeters will be at the same height as your ear. Align the front face of the front speakers with the front face of the centre speaker or place them slightly in front of the centre speakers.

It is best to install the Centre Speaker at the same height as the front speakers. You can also install it directly over or under the TV.

Place these speakers to the side of your listening position. If there isn't enough room, place these speakers so they face each other. Position them about 60 to 90cm above your ear, facing slightly downward.

* Unlike the front and centre speakers, the surround speakers are used mainly

for sound effects. Sound will not come from them all the time.

Subwoofer

Front (L)

Surround (L)

* HT-H5500W/HT-H5550W

Surround speakers must be connected to the wireless receiver module.

Centre

Product

Front (R)

Surround (R)

Wireless

Receiver Module

Connections

Subwoofer

* The appearance of your speakers may differ from the illustrations in this manual. * Match the speaker cables to the coloured label on the back of the speaker, and then plug them into

the jack of the same colour. See page 10 for exact instructions.

The position of the subwoofer is not so critical. Place it anywhere you like.

9 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 9HT-H5500_00W_30_50_50W-ENG_0402.indd 9 2014-04-02  1:07:362014-04-02  1:07:36

Connections

Installing the Speakers on the Tallboy Stand

* HT-H5530/HT-H5550/HT-H5550W only

1. Turn the Stand Base upside-down and

connect it to the Stand.

2. Use the driver to combine the screws on the 3 marked holes.

3. Straighten a supplied speaker wire to the gravity direction and put in the hole on the centre of Stand Base.

4. Connect the upper Speaker to the assembled Stand.

5. Insert a screw clockwise into the hole on the rear of the speaker using a screwdriver. And then connect a speaker cable.

6. This is the appearance after the speaker is installed. Follow this steps to install other speaker.

Stand Base

Stand

5 6

Speaker

Stand

Speaker Cable Connections

1. Match each speaker cable bundle to the correct speaker by matching the colour coded plug on each

bundle to the coloured sticker on the bottom of each speaker.

2. Connect the speaker wire plugs from each speaker to the back of the product by matching the colours of the speaker plugs to the colours of the speaker jacks.

10 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 10HT-H5500_00W_30_50_50W-ENG_0402.indd 10 2014-04-02  1:07:372014-04-02  1:07:37

In case of HT-H5500

SURROUND

Centre Speaker

Front Speaker (L)

Subwoofer

Front Speaker (R)

* Refer to page 6 for the speakers of HT-H5530/HT-H5550.

In case of HT-H5500W

Centre Speaker

Subwoofer

Surround

Speaker (L)

Surround

Speaker (R)

Wireless Receiver Module

* HT-H5500W/HT-H5550W should be connected with the SWA-6000 only. * Refer to page 6 for the speakers of HT-H5550W.

Surround Speaker (L)

Surround Speaker (R)

Front Speaker (L)

Front Speaker (R)

Connections

If you place a speaker near your TV set, the screen colour may be distorted because of the magnetic field.

✎

Place the wireless receiver module at the rear of the listening position. If the wireless receiver module is too

✎

close to the product, sound from the speakers may be disrupted because of interference. If you use a device such as a microwave oven, wireless LAN Card, Bluetooth device, or any other device

✎

that uses the 2.4/5.8GHz frequencies near the product, sound from the speakers may be disrupted because of interference.

11 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 11HT-H5500_00W_30_50_50W-ENG_0402.indd 11 2014-04-02  1:07:382014-04-02  1:07:38

Connections

The maximum transmission distance from the product to the wireless receiver module is about 10m, but

✎

may vary depending on your operating environment. If a steel-concrete wall or metallic wall is between the product and the wireless receiver module, the system may not operate at all, because the radio waves cannot penetrate metal.

If the product doesn't make a wireless connection, you need to run an ID Set between the product and

✎

wireless receiver module. With the product turned off, press "0""1""3""5" on the remote control. Turn on the wireless receiver module. Then, press and hold the "ID SET" button on the back of the wireless receiver module for 5 seconds, and then turn the product on.

| CAUTION |

If you want to install the speakers on the wall, fasten screws or nails (not provided) firmly to the wall wherever



you want to hang a speaker, and then, using the hole in the rear of each speaker, carefully hang each speaker on a screw or nail.

Do not let children play with or near the speakers. They could get hurt if a speaker falls.



When connecting the speaker wires to the speakers, make sure that the polarity (+/ –) is correct.



Keep the subwoofer speaker out of reach of children to prevent children from inserting their hands or alien



substances into the duct (hole) of the subwoofer speaker. Do not hang the subwoofer on the wall using the duct (hole).



The wireless receiving antenna is built into the wireless receiver module. Keep it away from water and



moisture. For optimal listening performance, make sure that the area around the wireless receiver module location is



clear of any obstructions. In 2-CH mode, you will hear no sound from the wireless surround speakers.



Attaching the Toroidal Ferrite Core to the Power Cord of the Wireless Receiver Module (SWA-6000)

* HT-H5500W/HT-H5550W only

If you attach a Toroidal ferrite core to the power cord of the wireless receiver module, it will help prevent RF interference from radio signals.

1. Pull the fixing tab of the Toroidal ferrite core to open it.

2. Make two loops in the wireless receiver module power cord.

3. Attach the Toroidal ferrite core to the wireless receiver module

power cord as shown in the figure on the right, and then close it by pressiing it until it clicks.

• Attach the ferrite core as close to the Wireless Receiver Module

as possible.

12 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 12HT-H5500_00W_30_50_50W-ENG_0402.indd 12 2014-04-02  1:07:392014-04-02  1:07:39

Connecting to a TV and External Devices

OPTICAL OUT

AUDIO OUT

HDMI IN

Red

White

External Devices

Method 1 Method 2

Connecting to a TV

Connect an HDMI cable (not supplied) from the HDMI OUT jack on the back of the product to the HDMI IN jack on your TV. If the TV supports ARC, you can hear the audio from your TV through the home cinema with only this cable connected. See page 18 in this manual and the section on ARC in your TV's user's manual for details.

Connecting to External Devices

To select the correct mode for an external device after you have connected the device, press the FUNCTION button. Each time you press the button, the mode changes in this order :

BD/DVD  D. IN  AUX  FM  BT

Two methods of connecting external devices to your home cinema are explained below.

Method 1 AUX IN : Connecting an External Analogue Component

Using an RCA audio cable (not supplied), connect the AUDIO In jack on the product to the AUDIO Out jack on the external analogue component.  Select the AUX mode.

• Be sure to match the colours on the cable plugs to the colours on the input and output jacks.

Method 2 OPTICAL : Connecting an External Digital Audio Component

Use to connect the digital audio output of digital signal components such as Cable Boxes and Satellite Receivers (Set-Top-Boxes): Using a digital optical cable (not supplied), connect the Optical Digital Audio In jack on the product to the Digital Optical Out jack of the external digital device using a digital optical cable.

Select the D. IN mode.



To see video from your Cable Box/Satellite receiver, you must connect its video output directly to your TV.

✎

This system supports Digital sampling frequencies of 32 kHz or higher from external digital components.

✎

This system supports only DTS and Dolby Digital audio. MPEG audio, a bitstream format, is not supported.

✎

Connections

13 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 13HT-H5500_00W_30_50_50W-ENG_0402.indd 13 2014-04-02  1:07:402014-04-02  1:07:40

Connections

Connecting to a Network Router

You can connect your product to your network router using one of the methods illustrated below.

Wired Network

Broadband modem

(with integrated router)

Broadband

service

Router

Broadband

service

Broadband

modem

Your router or your Internet Service Provider's

✎

policies may prevent the product from accessing Samsung's software update server. If this occurs, contact your Internet Service Provider (ISP) for more information.

DSL users, please use a router to make a network

✎

connection. To use the DLNA function, you must connect your

✎

PC to your network as shown in the illustrations above. The connection can be wired or wireless.

Wireless Network

Wireless IP sharer

Broadband

service

If your wireless IP router supports DHCP, this

✎

product can use a DHCP or static IP address to connect to the wireless network.

Set your wireless IP router to Infrastructure mode.

✎

Ad-hoc mode is not supported. The product supports only the following wireless

✎

security key protocols:

- WEP (OPEN/SHARED), WPA-PSK (TKIP/AES), WPA2-PSK (TKIP/AES)

Select a channel on the wireless IP router that is

✎

not currently being used. If the channel set for the wireless IP router is currently being used by another device nearby, it will result in interference and communication failure.

In compliance with the newest Wi-Fi certification

✎

specifications, Samsung home cinemas do not support WEP, TKIP, or TKIP-AES (WPS2 Mixed) security encryption in networks running in the

802.11n mode. Wireless LAN, by its nature, may cause

✎

interference, depending on the operating conditions (AP performance, distance, obstacles, interference by other radio devices, etc).

14 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 14HT-H5500_00W_30_50_50W-ENG_0402.indd 14 2014-04-02  1:07:402014-04-02  1:07:40

Settings

The Initial Settings Procedure

• The Home menu will not appear if you do not configure the initial settings.

• The OSD (On Screen Display) may change in this product after you upgrade the software version.

• The access steps may differ depending on the menu you selected.

1. Turn on your TV after connecting the product, and then turn on the product. When you turn on the product for the first time, the product automatically displays the Initial Settings Language screen.

2. Press the ▲▼ buttons to select the desired language, and then press the E button.

3. Press the E button to start function setup.

Initial Settings

TV Aspect and Network will be set. Each setting may be changed later under "Settings"

Start

Previous " Select

4. The TV Aspect screen appears. Press the ▲▼

buttons to select a TV aspect ratio, and then press the E button. You have four choices: 16:9 Original - For widescreen TVs. Displays widescreen pictures in their original 16:9 format and 4:3 pictures (the old, standard format) in 4:3 pillar box format with black bars on the left and right. 16:9 Full - For widescreen TVs. Displays widescreen pictures in their original 16:9 format and expands 4:3 pictures to fill the 16:9 screen. 4:3 Letter Box - For older, standard screen, analogue TVs. Displays 4:3 pictures in full screen and 16:9 pictures in letter box format that retains the 16:9 aspect ratio but puts black bars above and below the picture.

4:3 Pan-Scan - For older, standard screen, analogue TVs. Displays 4:3 pictures in full screen and 16:9 pictures in Pan-Scan format that fills the screen, but cuts off the left and right sides of the picture and enlarges the middle vertically.

5. The Network screen appears.

- Before you begin, confirm that the product is connected to your router.

- Set to wired or wireless depending on your network environment.

- If you have a network with static IP addresses, we suggest you select Skip by pressing the

BLUE (D) button.

If you skip network setup here or the setup does

✎

not work correctly, you can set up the product's network connection later. (See page 20)

Initial Settings | Network

Select your network type. Network Type

6. The product verifies the network connection

and then connects to the network. When it is done, press the E button. The "Initial settings completed." screen appears, and then the Home screen appears.

If you want to display the Initial Settings screen

✎

again and make changes, select the Reset option. (See page 20)

If you use an HDMI cable to connect the product

✎

to an Anynet+ (HDMI-CEC)-compliant Samsung TV and 1.) You have set the Anynet+ (HDMI-CEC) feature to On in both the TV and the product and

2.) You have set the TV to a language supported by the product, the product will select that language as the preferred language automatically.

Connect

Wireless

Wired

㾎

Network cable connected.

Settings

15 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 15HT-H5500_00W_30_50_50W-ENG_0402.indd 15 2014-04-02  1:07:422014-04-02  1:07:42

Settings

The Home Screen at a Glance

Play disc

Blu-ray

App 1 App 2 App 3 App 4

Photos Videos Music

Opera TV

Store

Screen

Mirroring

Change

Device

Function

Settings

3456789

Play disc

The disc currently in the tray is displayed. Press E to start playing the disc.

Photos/Videos/Music

Play photos, videos, or music content from Disc, USB, PC, or mobile devices.

Apps

Access various for pay or free-of-charge applications.

Opera TV Store

Makes the Web-based App for TV available for use.

A list of useful and popular apps we recommend.

Screen Mirroring

Set up the wireless mirroring function between the home cinema and a smart phone or tablet.

Change Device

Displays a list of external devices connected to the main unit. Switch to the desired device.

Function

Use for switching to an external device, and for radio and mode switching for a Bluetooth connection. You can use the remote control’s

FUNCTION button and the main unit’s button

for mode switching.

Settings

Set various functions to suit your personal preferences.

To play or view video, photo, music files located

✎

on your PC, you must connect your home cinema and PC to a home network and you must download, install, and configure the DLNA software on your PC. (See page 25)

Accessing the Settings Screen

1. Select Settings on the Home screen, and then press E. The Settings screen appears.

Settings

Display

Audio Network System Language Security General Support

2. To access the menus, sub-menus, and options

on the Settings screen, please refer to the remote control illustration. (See page 17)

If you leave the product in the stop mode for more

✎

than 5 minutes without using it, a screen saver will appears on your TV. If the product is left in the screen saver mode for more than 20 minutes, the power automatically turns off.

3D Settings TV Aspect Ratio : 16:9 Original BD Wise : Off Resolution : Auto Movie Frame (24 fps) : Off HDMI Colour Format : Auto HDMI Deep Colour : Off Progressive Mode : Auto

16 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 16HT-H5500_00W_30_50_50W-ENG_0402.indd 16 2014-04-02  1:07:432014-04-02  1:07:43

Buttons on the Remote Control Used

TOOLS

RETURN

EXIT

INFO

SUBTITLE HOME

REPEAT

Settings Menu Functions

for the Settings Menu

Display

HOME Button : Press to move to the Home

screen.

RETURN Button : Press to return to the

previous menu.

ENTER) / DIRECTION Button :

(

• Press select an item.

• Press the E button to activate the currently selected item or confirm a setting.

EXIT Button : Press to exit the current

menu.

Detailed Function Information

Each Settings function, menu item, and individual option is explained in detail on-screen. To view an explanation, use the ▲▼◄► buttons to select the function, menu item, or option. The explanation will usually appear on the bottom of the screen.

A short description of each Settings function starts on this page. Additional information on some of the functions is also in the Appendix of this manual.

to move the cursor or

▲▼◄►

3D Settings

Set up the 3D related functions.

3D Blu-ray Playback Mode: Select whether to

play a Blu-ray Disc with 3D contents in 3D Mode. If you move to the Home menu while in 3D mode, the product will switch to 2D automatically.

Screen Size: Enter the size of the TV attached to

the product. The product will automatically adjust the 3D output to the screen size of the TV.

Carefully read the health and safety information

✎

before viewing 3D content. (See page 3)

TV Aspect Ratio

Lets you adjust the output of the product to the screen size of your TV. (See page 40)

BD Wise

BD Wise is Samsung’s latest inter-connectivity

feature. When you connect a Samsung product and a Samsung TV with BD Wise to each other via HDMI, and BD Wise is on in both the product and TV, the product outputs video at the video resolution and frame rate of the Blu-ray/DVD Disc.

Resolution

Lets you set the output resolution of the HDMI video signal to BD Wise, Auto, 1080p, 1080i, 720p, 576p/480p. The number indicates the number of lines of video per frame. The i and p indicate interlaced and progressive scan, respectively. The more lines, the higher quality.

Movie Frame (24 fps)

Setting the Movie Frame (24 fps) feature to Auto lets the product adjust its HDMI output to

24 frames per second automatically for improved picture quality if attached to a 24Fs compatible TV.

• You can enjoy the Movie Frame (24 fps) feature only on a TV supporting this frame rate.

• Movie Frame is only available when the product is in the HDMI 1080p output resolution modes.

Settings

HT-H5500_00W_30_50_50W-ENG_0402.indd 17HT-H5500_00W_30_50_50W-ENG_0402.indd 17 2014-04-02  1:07:442014-04-02  1:07:44

17 - English

Settings

HDMI Colour Format

Lets you set the colour space format for the HDMI output to match the capabilities of the connected device (TV, monitor, etc).

HDMI Deep Colour

Lets you set the product to output video from the HDMI OUT jack with Deep Colour. Deep Colour provides more accurate colour reproduction with greater colour depth.

Progressive Mode

Lets you improve picture quality when viewing DVDs.

Audio

Speaker Settings

Lets you adjust the following speaker settings and turn the test tone on and off so you can test the speakers.

Level

: Lets you adjust the relative loudness of each speaker from 6dB to -6dB. For example, if you like deep bass, you can increase the loudness of the subwoofer by 6dB.

Distance

Test Tone

Speaker Selection

Lets you select which speakers you want active, either the TV's speakers or the home cinema's speakers.

Audio Return Channel

Lets you direct the sound from the TV to the Home Cinema speakers. Requires an HDMI connection and an Audio Return Channel (ARC) compatible TV.

• If Audio Return Channel is set to on and you

• If Audio Return Channel is set to Auto and you

: Lets you adjust the relative distance of each speaker from the listening position up to 9 meters. The farther the distance, the louder the speaker will be.

: Lets you run the Test Tone function so you can test your adjustments. Setting Test Tone to On turns the Test Tone on. Setting it to Off turns it off.

are using an HDMI cable to connect the product to the TV, digital optical input will not work.

are using an HDMI cable to connect the product to the TV, ARC or digital optical input is selected automatically.

Digital Output

Lets you set the Digital Output to match the capabilities of the AV receiver you’ve connected to the product. For more details, please refer to the digital output selection table. (See page 45)

Dynamic Range Control

Lets you apply dynamic range control to Dolby Digital, Dolby Digital Plus, and Dolby TrueHD audio.



Auto: Automatically controls the dynamic range of Dolby TrueHD audio, based on information in the Dolby TrueHD soundtrack. Also turns dynamic range control off for Dolby Digital and Dolby Digital Plus.

Off: Leaves the dynamic range uncompressed,

letting you hear the original sound.

On: Turns dynamic range control on for all three

Dolby formats. Quieter sounds are made louder and the volume of loud sounds is reduced.

Downmixing Mode

Lets you select the multi-channel downmix method that is compatible with your stereo system. You can choose to have the product downmix to

Normal Stereo or to Surround Compatible.

Audio Sync

When the product is attached to a digital TV, lets you adjust the audio delay so that the audio syncs with the video. You can set the delay between 0 and 300 milliseconds.

Network

Network Settings

Lets you configure the network connection so you can enjoy various features such as Internet services or DLNA Wi-Fi functionality, and perform software upgrades.

Network Test

Lets you test the Internet Protocol setup to see if it is working correctly.

Network Status

Lets you check the current network and Internet status.

18 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 18HT-H5500_00W_30_50_50W-ENG_0402.indd 18 2014-04-02  1:07:452014-04-02  1:07:45

Wi-Fi Direct

Lets you connect a Wi-Fi Direct device to the product using a peer-to-peer network, without the need for a wireless router. Note that if the product is connected to a wireless network, it may be disconnected when you use Wi-Fi Direct. (

Text files, such as files with a .TXT or .DOC

✎

extension, will not display when you are using the

Wi-Fi Direct function.

Screen Mirroring

The Screen Mirroring function lets you view the screen of your smart phone or smart device on the TV you have connected to the home cinema system. (

Device Name

Lets you assign an identifying name to the product. You use this name to identify the product when you are connecting external Wi-Fi devices (smart phones, tablets, etc.) to it.

BD-Live Internet Connection

Lets you allow or prohibit an Internet connection for the BD-Live service.

Initial Settings

Lets you re-run the Initial Settings procedure. (See page 15)

Quick start

You can turn on the power quickly by decreasing the boot time.

If this function is set to On, Standby power

✎

consumption will be increased. (About 12W ~ 20W)

Anynet+ (HDMI-CEC)

Anynet+ is a convenient function that offers linked operations with other Samsung products that have the Anynet+ feature and lets you control those products with one Samsung TV remote. To operate this function, you must connect this product to an Anynet+ Samsung TV using a HDMI cable.

See page 22)

See page 39)

System

BD Data Management

Lets you manage the contents you downloaded through a Blu-ray disc that supports the BD-Live service. You can view the information about the USB device you are using for BD Live data storage including the storage space. You can also delete BD Live data and change the device.

DivX® Video On Demand

View DivX® VOD Registration Codes to purchase and play DivX® VOD contents.

Language

Lets you select the language you prefer for the OnScreen Menu, disc menu, etc.

• The selected language will only appear if it is supported on the disc.

Security

The default PIN is 0000. Enter the default PIN to access the security function if you haven't created your own PIN.

BD Parental Rating

Prevents playback of Blu-ray Discs with a rating equal to or above a specific age rating unless you enter the PIN.

DVD Parental Rating

Prevents playback of DVDs with a rating above a specific numerical rating unless you enter the PIN.

Change PIN

Changes the 4-digit PIN used to access security functions.

General

Time Zone

Lets you specify the time zone that is applicable to your area.

Settings

19 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 19HT-H5500_00W_30_50_50W-ENG_0402.indd 19 2014-04-02  1:07:452014-04-02  1:07:45

Settings

Support

Software Upgrade

For more information about this function see page

23.

Contact Samsung

Provides contact information for assistance with your product.

View the general disclaimer regarding third party contents and services.

Reset

Reverts all settings to their defaults except for the network. Requires that you enter your security PIN. The default security PIN is 0000.

Network Setup

When you connect this product to a network, you can use network based applications and functions such as BD-LIVE and upgrade the product's software through the network connection.

Configuring Your Network Connection

To begin configuring your network connection, follow these steps:

1. In the Home screen, select Settings, and then press the E button.

2. Select Network, and then press the E button.

3. Select Network Settings, and then press the

button.

4. Go to the instructions for Wired networks starting below or the instructions for Wireless networks. (See page 21)

Wired Network



Wired – Automatic

After following Steps 1 to 3 above:

1. In the Network Settings screen, change Network Type to Wired. Then, select Connect

and press the E button. The product detects the wired connection, verifies the network connection, and then connects to the network.

2. When it is done, highlight OK, and then press button.



Wired - Manual

If you have a static IP address or the automatic procedure does not work, you'll need to set the Network Settings values manually.

After following Steps 1 to 3 above:

1. In the Network Settings screen, change

Network Type to Wired. Then, select Connect

and press the E button. The product searches for a network, and then displays the connection failed message.

If it is possible to connect the home cinema to

✎

your network wirelessly, select Change Network at this point, change the Network Type to Wireless, and then go to the instructions for wireless networks. (See page 21)

Network Settings

Wired network connection failed.

IP auto setting failed. Try the following to set up the IP automatically, or set up the IP manually by selecting IP Settings.

Ensure that the DHCP server is enabled on the wireless network, then unplug and plug the wireless

network in again.

- Contact your internet service provider for more info.

Change Network

MAC Address XX:XX:XX:XX:XX:XX IP Address 0. 0. 0. 0 Subnet Mask 0. 0. 0. 0 Gateway 0. 0. 0. 0 DNS Server 0. 0. 0. 0

IP Settings Retry Close

a Previous d Skip < Move " Select

2. Use the ◄► buttons to select IP Settings,

and then press the E button. The IP Settings screen appears.

3. Select the IP setting field, and then set it to

Enter manually.

4. Select a parameter to enter (IP Address, for

example), and then press E. Use the number keypad on your remote control to enter the numbers for the parameter. You can also enter numbers using the ▲▼ buttons. Use the ◄► buttons on the remote control to move from entry field to entry field within a parameter. When done with one parameter, press the E button.

5. Press the ▲ or ▼ button to move to another

parameter, and then enter the numbers for that parameter following the instructions in Step 4.

20 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 20HT-H5500_00W_30_50_50W-ENG_0402.indd 20 2014-04-02  1:07:452014-04-02  1:07:45

6. Repeat Steps 4 and 5 until you have filled in all parameters.

You can get the network parameter values from

✎

your Internet provider.

7. When finished entering all the parameter values, select Return ('), and then press the E button. The home cinema verifies the network connection and then connects to the network.

Wireless Network

You can set up a wireless network connection in three ways:

- Wireless Automatic

- Wireless Manual

- WPS(PBC)

Before you configure the wireless network connection, disconnect any wireless network devices currently connected to the product or, if applicable, the product's current wired connection.



Wireless - Automatic

Follow the Steps 1 to 3 in "Configuring Your Network Connection". (See page 20)

1. In the Network Settings screen, change Network Type to Wireless. The product

searches for and then displays a list of the available networks.

Network Settings

Select your network type.

Network Type Wireless

Wireless network

㾎

si-ap

MIC

KIMING_VTOWER

WPS(PBC) Search

You can connect your BD Home Theater to the internet. Please select which wireless network to use.

m Move " Select ' Return

2. Select the desired network, and then press the

button.

3. On the Security screen, enter your network's security code or pass phrase. Enter numbers directly using the number buttons on your remote control. Enter letters by selecting a letter with ▲▼◄► buttons, and then pressing

button.

4. When finished, select Done, and then press the button. The product verifies the network

connection and then connects to the network.

You should be able to find the security code or

✎

pass phrase on one of the set up screens you used to set up your router or modem.



Wireless - Manual

If you have a static IP address or the Automatic procedure does not work, you'll need to set the Network Settings values manually.

Follow the Steps 1 to 3 in "Configuring Your Network Connection". (See page 20)

1. In the Network Settings screen, change

Network Type to Wireless. The product

searches for and then displays a list of the available networks.

2. Scroll through the list, select the desired network

or Add Network, and then press the

button.

3. If you selected a network in Step 2, go to Step 6.

If you selected Add Network, go to Step 4.

4. Enter your wireless network or wireless router's

name.

• Enter numbers directly using the number buttons on your remote control.

• Enter letters by selecting a letter with the ▲▼◄► buttons, and then pressing the E button.

• To display capital letters (or redisplay lower case letters if capital letters are displayed),

select

, and then press the E button.

• To display symbols and punctuation, select 123#&, and then press the E button. To

redisplay letters, select 123#&, and then press the E button.

When finished, select Done, and then press the

button.

5. On the Security method screen that appears, use the ▲▼ buttons to select the network's Security method, and then press the E button. On the next screen, enter your network's security code or pass phrase.

• Enter numbers directly using the number

buttons on your remote control.

• Enter letters by selecting a letter with the

▲▼◄► buttons, and then pressing the E button.

Settings

21 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 21HT-H5500_00W_30_50_50W-ENG_0402.indd 21 2014-04-02  1:07:462014-04-02  1:07:46

Settings

When finished, select Done, and then press the E button. The product searches for the network.

6. The Network connection fail screen appears. Use ◄► buttons to select IP Settings, and then press the E button.

7. Select the IP setting field, and then set it to Enter manually.

8. Select a network parameter to enter (IP Address, for example), and then press

button. Use the number keypad on your remote control to enter the numbers for the parameter. You can also enter numbers using the ▲▼ buttons. Use the ◄► buttons on the remote control to move from entry field to entry field within a parameter. When done with one value, press the E button.

9. Press the ▲ or ▼ button to move to another parameter, and then enter the numbers for that parameter following the instructions in Step 8.

10. Repeat Steps 8 and 9 until you have filled in all parameters.

You can get the Network parameter values from

✎

your Internet provider.

11. When finished, select Return ('), and then press the E button. The Security Key screen appears.

12. On the Security Key screen, enter your network's Security Code or Pass Phrase. Enter numbers directly using the number buttons on your remote control. Enter letters by selecting a letter with the ▲▼◄► buttons, and then pressing the E button.

13. When finished, select Done at the right of the screen, and then press the E button. The product verifies the network connection and then connects to the network.

14. After the home cinema verifies the network, select OK, and then press the E button.

You can also begin the Manual Network setup by

✎

going to Settings > Network > Network Status.



WPS(PBC)

One of the easiest ways to set up the wireless network connection is using the WPS(PBC) function. If your wireless router has a WPS(PBC) button, follow these steps:

Follow the Steps 1 to 3 in "Configuring Your Network Connection". (See page 20)

1. In the Network Settings screen, change Network Type to Wireless. The product

searches for and then displays a list of the available networks.

2. Scroll the list down, select WPS(PBC), and then press the E button.

3. Press the WPS(PBC) button on your router within two minutes. Your product automatically acquires all the network settings values it needs and connects to your network after the network connection is verified.

4. When it is done, highlight OK, and then press the E button.

For a WPS connection, set your wireless router’s

✎

security encryption to AES. WEP security encryption does not support a WPS connection.

Wi-Fi Direct

The Wi-Fi Direct function allows you to connect WiFi Direct devices to the product and each other using

a peer-to-peer network, without a wireless router.

Some Wi-Fi Direct devices may not support the

✎

DLNA function if connected via Wi-Fi Direct. If this is the case, change the network connection method you used to connect the device to the home cinema.

Wi-Fi Direct transmissions can interfere with

✎

Bluetooth signals. Before you use the Bluetooth function, we strongly recommend that you turn off the Wi-Fi Direct function on any device in which it is currently on.

1. Turn on the Wi-Fi Direct device and activate its Wi-Fi Direct function.

2. In the Home screen, select Settings, and then

press the E button.

3. Select Network, and then press the E button.

22 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 22HT-H5500_00W_30_50_50W-ENG_0402.indd 22 2014-04-02  1:07:462014-04-02  1:07:46

4. Select Wi-Fi Direct, and then press the E button. The Wi-Fi Direct devices that you can connect to appear.

Settings

Display

Device Name : HT-H5500

Audio

Select your Wi-Fi Direct device to connect to.

Network

AndroidXXXXXXX Not Connected

System Language Security General Support

Wi-Fi Direct

Refresh

5. You have three ways to complete the Wi-Fi

connection:

• Through the Wi-Fi device.

• Through the product using PBC.

• Through the product using a PIN.

Each is covered below.

Through the Wi-Fi Device

1. On the Wi-Fi device, follow the device's procedure for connecting to another Wi-Fi Direct device. See the device's user manual for

instructions.

2. When you have completed the procedure, you should see a pop-up on your TV screen saying that a device that supports Wi-Fi Direct has

requested to connect. Select OK, and then press the E button to accept.

3. The Connecting pop-up appears, followed by the Connected pop-up. When it closes, you should see the device listed on the Wi-Fi Direct

screen as connected.

• The PBC and PIN procedures connect devices automatically.

Through the Product Using PBC

1. Select the Wi-Fi Direct device you want to

connect to this product, and then press the E button.

2. The Connecting pop-up appears, followed by the Connected pop-up. When it closes, you should see the device listed on the Wi-Fi Direct screen as connected.

Through the Product Using a PIN

1. Select the Wi-Fi Direct device you want to

connect to this product, and then press the E button.

2. The PIN pop-up appears.

3. Note the PIN code in the pop-up, and then enter

it into the appropriate field in the Wi-Fi Direct device you want to connect.

4. The Connecting pop-up appears, followed by the Connected pop-up. When it closes, you should see the device listed on the Wi-Fi Direct screen as connected.

The current wired or wireless network connection

✎

will be disconnected when you use the Wi-Fi Direct function.

Text files, such as files with a .TXT or .DOC

✎

extension, will not display when you are using the

Wi-Fi Direct

function.

Upgrading Software

The Software Upgrade menu allows you to upgrade the product’s software for performance improvements or additional services.

• Never turn the product off or back on manually during the update process.

• The update is complete when the product turns off after restarting. Press the turn on the updated product for your use.

• Samsung Electronics takes no legal responsibility for product malfunction caused by an unstable Internet connection or consumer negligence during a software upgrade.

1. In the Home menu, select Settings, and then press the E button.

2. Select Support, and then press the E button.

3. Select Software Upgrade, and then press the

button.

POWER button to

Settings

23 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 23HT-H5500_00W_30_50_50W-ENG_0402.indd 23 2014-04-02  1:07:472014-04-02  1:07:47

Settings

4. Select one of the following methods:

• By Online

• By USB

• Auto Upgrade Notification

5. Press the E button.

Directions for each method begin below.

If you want to cancel the upgrade while the

✎

upgrade software is downloading, press the E button.

By Online

Your product must be connected to the Internet to use the By Online function. Remove all discs before you begin.

1. Select By Online, and then press the E button. The Connecting to Server message appears.

2. If an update is available, a popup message appears asking if you want to upgrade. If you select Yes, the product turns off automatically, turns on, and then begins the upgrade.

3. The update progress popup appears. When the update is completed, the product turns off automatically again.

4. Press the product.

POWER button to turn on the

By USB

1. Visit www.samsung.com.

2. Click SUPPORT on the top right of the page.

3. Enter the product's model number into the

search field. As you enter the model number, a drop down will display products that match the model number.

4. Left click your product's model number in the drop down list.

5. On the page that appears, scroll down to and then click Firmware Manuals & Downloads.

6. Click Firmware in the centre of the page.

7. Click the ZIP icon in the File column on the right

side of the page.

8. Click Send in the first pop-up that appears. Click OK in the second pop-up to download and save the firmware file to your PC.

9. Unzip the zip archive to your computer. You should have a single folder with the same name as the zip file.

10. Copy the folder to a USB flash drive.

11. Make sure no disc is inserted in the product,

and then insert the USB flash drive into the USB port of the product.

12. In the product’s menu, go to Settings > Support > Software Upgrade.

13. Select By USB.

14. The home cinema searches for the software on

the USB drive. When it finds the software, the Update Request pop-up appears.

15. Select OK. The home cinema turns off, turns on, and then begins the upgrade. When the upgrade is done, the home cinema turns off.

16. Press the cinema.

There should be no disc in the product when you

✎

upgrade the software using the USB Host jack. When the software upgrade is done, check the

✎

software details in the Software Upgrade menu.

POWER button to turn on the home

Auto Upgrade Notification

If your product is connected to the network and you set Auto Upgrade Notification on, the product will notify you if a new software version is available with a pop-up message.

1. Turn on the product.

2. In the Software Upgrade menu, set Auto Upgrade Notification to On.

If there is a new software version available, the product will notify you with a pop-up message.

3. To upgrade the firmware, select Ye s. The product turns off automatically, turns on, and then begins the upgrade.

4. The update progress popup will appear. When the update is complete, the product will turn off automatically again.

5. Press the product.

POWER button to turn on the

24 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 24HT-H5500_00W_30_50_50W-ENG_0402.indd 24 2014-04-02  1:07:472014-04-02  1:07:47

Setting Up DLNA

DLNA enables you to play music, video, and photo files located in your PC using this product. To use DLNA, you must connect the product to your PC via the network (See page 14) and install the SAMSUNG PC Share Manager on the PC.

To Download the DLNA Software

To use DLNA with your PC, you must install DLNA software on your PC. You can download the PC software and get detailed instructions for using DLNA from the Samsung.com website.

1. Go to www.samsung.com.

2. Click SUPPORT at the top of the page.

3. Enter the product's model number into the

search field. As you enter the model number, a drop down will display products that match the model number.

4. Left click your product's model number in the drop down list.

5. On the page that appears, scroll down to and then click Firmware Manuals & Downloads.

6. Click the Software tab.

7. On the software tab, click the EXE icon on the

right side of the DLNA line.

8. In the first pop-up that appears, click Send. In the second pop-up, click Save File.

9. Find the DLNA install file on your disk, and then double click the file.

10. In the pop-up that appears, click Run, and then follow the directions that appear on your screen.

Download the DLNA Installation/Instruction manual from the same Software Tab by clicking the corresponding PDF file symbol in the File column on the right. The file, in PDF format, will download and open. Follow the directions to install and setup DLNA. You can view and/or save the file.

To use DLNA with your smart phone, you need to

✎

connect your home cinema and smart phone to the same network.

Settings

25 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 25HT-H5500_00W_30_50_50W-ENG_0402.indd 25 2014-04-02  1:07:472014-04-02  1:07:47

Playing Content

Your home cinema can play content located on Blu-ray/DVD/CD discs, USB devices, PCs, smart phones, tablets, and in Apps.

To play content located on your PC or a mobile device, you must connect the PC or mobile device and the product to your network. To play content on your PC, you must also download and install DLNA network software or already have DLNA network software on your PC.

PCs running Windows 7 and Windows 8 have

✎

DLNA software (Play To) built in.

Switching the Source Device

If two or more external devices are connected to the main unit, you can use any of the three methods described below to change the source device.

Method 1

From the Home screen, use the ▲▼◄► buttons to move to Change Device, and then press E.

The Change Device popup window will appear. Use the ▲▼ buttons to move to the desired device, and then press E.

Method 2

If you move to Photos, Videos, Music or other filebased contents, a list of folders and files will appear. Press the RED (A) button to display the Change Device popup window, use the ▲▼ buttons to move to the desired device, and then press E.

Method 3

When a device is connected for the first time, a popup window appears on which you can change the source device by using the ◄► buttons.

Playing Commercial Discs

1. Press the  button to open the disc tray.

2. Place a disc gently into the disc tray with the

disc’s label facing up.

3. Press the  button to close the disc tray. Playback starts automatically.

4. If playback does not start automatically, press the 6 button on the remote.

Disc Storage & Management

• Holding Discs

- Fingerprints or scratches on a disc may reduce sound and picture quality or cause skipping.

- Avoid touching the surface of a disc where data has been recorded.

- Hold the disc by the edges so that fingerprints will not get on the surface.

- Do not stick paper or tape on the disc.

• Cleaning Discs

- If you get fingerprints or dirt on a disc, clean it with a mild detergent diluted in water and wipe with a soft cloth.

- When cleaning, wipe gently from the inside to the outside of the disc.

- Disc Storage

Do not keep in direct sunlight. Keep in a cool ventilated area. Keep in a clean protective jacket and store

vertically.

Playing a Disc with User Recorded Content

You can play multimedia files you have recorded on Blu-ray, DVD, or CD discs.

1. Place a user recorded disc into the disc tray with the disc’s label facing up, and then close the tray.

2. Use the ▲▼◄► buttons to select the type of content you want to view or play - Photos, Videos, or Music - and then press the E button.

-1

. Select Play disc from the Home screen. The

Play disc screen appears. Use the ▲▼ buttons to select the desired content type, Photos, Videos, or Music.

26 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 26HT-H5500_00W_30_50_50W-ENG_0402.indd 26 2014-04-02  1:07:482014-04-02  1:07:48

3. A screen appears listing the contents of the disc.

App

Device

Function

Videos

Music

Depending on how the contents are arranged, you will see either folders, individual files, or both.

4. If necessary, use the ▲▼◄► buttons to select a folder, and then press the E button.

5. Use the ▲▼◄► buttons to select a file to view or play, and then press the E button.

6. Press the

RETURN button one or more times to

exit a current screen, exit a folder, or to return to the Home screen. Press the EXIT button to return directly to the Home Screen.

7. Go to pages 28~32 for instructions that explain how to control playback of videos, music, and pictures on a disc.

Playing Files on a USB Device

There are two methods you can use to play or view multimedia files located on a USB device through your product.

Method 1 : If you connect a USB device while the product is turned on

1. The "New device connected." pop-up appears.

Play disc

ay dis

Photos Videos Music

oto

New device connected.

USB DISK

Photos

Videos

Blu-ray

u-ra

Music

3. If necessary, use the ▲▼◄► buttons to select

a folder, and then press the E button.

4. Select a file to view or play, and then press the button.

5. Press the

RETURN button to exit a folder or the

EXIT button to return to the Home screen.

6. Go to pages 28~32 for instructions that explain

how to control playback of videos, music, and pictures on a USB device.

Method 2 : If the product is turned on after you connect a USB device

1. Turn the product on.

2. Press Change Device and select a USB device.

3. Use the ◄► buttons to select Photos, Videos,

or Music on the Home screen, and then press the E button.

4. If necessary, use the ▲▼◄► buttons to select

a folder, and then press the E button.

5. Select a file to view or play, and then press the button.

6. Press the

RETURN button to exit a folder or the

EXIT button to return to the Home screen.

7. Go to pages 28~32 for instructions that explain

how to control playback of videos, music, and pictures on a USB device.

If you insert a disc when playing a USB device

✎

or phone, the device mode changes to "Disc" automatically.

If your cellular phone is DLNA compatible, you

✎

can play contents without connecting a USB cable. (See page 37)

Playing Content

App 1 App 2 App 3 App 4

1 App 2 App 3 App 4

If the pop-up does not appear, go to Method 2.

✎

Opera TV

pera TV

tore

Store

Mor

Screen

Mirroring

irrorin

Change

hange

Device

Function

Settings

ettin

2. Use the ▲▼ buttons to select Photos, Videos,

or Music and then press the E button. Depending on how the contents are arranged, you will see either folders, individual files, or both.

27 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 27HT-H5500_00W_30_50_50W-ENG_0402.indd 27 2014-04-02  1:07:482014-04-02  1:07:48

Playing Content

SUBTITLE HOME

REPEAT

DISC MENU

TITLE MENU

POPUP

Controlling Video Playback

You can control the playback of video content located on a Blu-ray/DVD disc, USB device, mobile device, or PC. Depending on the disc or contents, some of the functions described in this manual may not be available.

Buttons on the Remote Control used for Video Playback

Playback related buttons

The product does not play sound in Search, Slow, or Step mode.

• To return to normal speed playback, press the button.

Fast

Motion

Play

Slow

Motion

Play

Step

Motion

Play

Skip

Motion

Play

Starts playback.

Stops playback.

Pauses playback.

During playback, press the 3 or

button.



Each time you press the 3 or  button, the playback speed will change.

In pause mode, press the  button. Each time you press the  button, the playback speed will change.

In pause mode, press the 7 button. Each time you press the 7 button, a new frame appears.

During playback, press the 1 or

button.

Each time you press the 1 or

button, the disc moves to the

previous or next chapter or file.

Using the disc menu, title menu, popup

menu, and title list

DISC MENU

During playback, press this button to display the Disc menu.

TITLE MENU

During playback, press this button to display the Title menu.

• If your disc has a playlist, press the button to go to the playlist.

POPUP MENU

During playback, press this button to display the Popup menu.

Repeat Playback

1. During playback, press the REPEAT button

on the remote control.

2. Press the ▲▼ buttons to select Off, Title,

Chapter, All or Repeat A-B, and then press

the E button.



Repeat A-B

1. Press the E button at the point where you

want repeat play to start (A).

2. Press the E button at the point where you

want repeat play to stop (B).

3. To return to normal play, press the REPEAT

button again.

4. Press the E button.

Depending on the disc, the screen may not

✎

display all repeat options. The screen may not display Chapter or Title

✎

immediately. Continue to press the ▲▼ buttons until your choice is inside the applicable field.

To return to normal play, press the REPEAT

✎

button again, press the ▲▼ buttons to select Off, and then press the E button.

The screen may not display Repeat A-B

✎

immediately. Continue to press the ▲▼ buttons until Repeat A-B is inside the applicable field.

You must set point (B) at least 5 seconds of

✎

playing time after point (A).

GREEN (B)

28 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 28HT-H5500_00W_30_50_50W-ENG_0402.indd 28 2014-04-02  1:07:492014-04-02  1:07:49

Using the TOOLS Menu

During playback, press the TOOLS button.

Title

If there is more than one title on a disk or device, lets you move to or select a desired title.

Playing Time

Lets you go to a specific playback point. Use the numeric buttons to input the playback point.

Repeat Mode

Lets you repeat a specific title, chapter, or marked section.

Audio Sync

Lets you adjust the audio delay so that the audio syncs with the video. You can set the delay from 0 to 300 milliseconds.

Picture Settings

Lets you set the picture mode.

Mode

- User : Lets you adjust the Brightness, Contrast, Colour, and Sharpness functions

manually.

- Dynamic : Choose this setting to increase sharpness.

- Normal : Choose this setting for most viewing applications.

- Movie : This is the best setting for watching movies.

Menu selections that appear only when a BD/DVD disc plays

Chapter

Lets you move to a chapter that you want to watch.

Audio

Lets you set the desired audio language.

Subtitle

Lets you set the desired subtitle language.

Angle

To view a scene from another angle. The Angle option displays the number of angles available to view (1/1, 1/2, 1/3, etc.).

BONUSVIEW Video BONUSVIEW Audio

Lets you set the desired Bonusview option.

Menu selections that appear only while a file plays

Full Screen

Lets you set the desired full screen size. You can select Original, Mode1 (larger), and Mode2 (largest).

Information

Select to view video file information.

Depending on the disc or storage device, the

✎

Tools menu may differ. All options may not be displayed.

Creating a Video Playlist

You can create a playlist of video files in a way that is nearly identical to the way you create a playlist of music files. See page 30 for instructions.

Playing a Pre-Recorded Commercial Audio Disc

1. Insert an Audio CD (CD-DA) or an MP3 Disc into the disc tray.

• For an Audio CD (CD-DA), the first track will

be played automatically. Tracks on a disc are played in the order in which they were recorded on the disc.

•

For an MP3 disc, press the ◄► buttons to select Music, then press the E button.

Playing Content

29 - English

HT-H5500_00W_30_50_50W-ENG_0402.indd 29HT-H5500_00W_30_50_50W-ENG_0402.indd 29 2014-04-02  1:07:502014-04-02  1:07:50

DISC MENU

PTY - PTY SEARCH PTY +

RDS DISPLAY TA

TITLE MENU

POPUP

Playing Content

Playlist

TRACK 001

To play a particular track, use the ▲▼ buttons on

Repeat Mode Track Rip

00:00/00:00

" Pause  Select

the remote to select the track, and then press the

button.

For more information about playing music, see

✎

Controlling Music Playback below.

Controlling Music Playback

You can control the playback of music content located on a DVD, CD, USB, mobile device, or PC. Depending on the disc or contents, some of the functions described in this manual may not be available.

Buttons on the Remote Control used for Music Playback

Number buttons : During Playlist playback, press the desired track number. The

selected track is played.

Skip : During playback, press the 1 or

button to move to the previous or next

music track.

button : Stops a track.

Tools

> Move < Adjust ' Return

TRACK 003 04:41

TRACK 004 04:02

TRACK 005 03:43

TRACK 006 03:40

Tools ' Return

0/16

5 6

30 - English

Fast Play (Audio CD [CD-DA] only) :

During playback, press the 3 or  button.

Each time you press the 3 or  button, the playback speed will change.

button : Pauses a track.

button : Plays the currently selected

track.

Repeating Tracks

You can set the product to repeat tracks.

1. During music playback, press the TOOLS button.

2. Use ◄► button to select Off, Track or One, All or Shuffle in Repeat Mode, and then press the

button.

Creating a Music Playlist

1. If playing music from a commercial CD or DVD,

press the 5 or RETURN button. The Music List Screen appears. If you are creating a playlist from music on a user created disk or USB device, access the Music list as described on page 26 or 27.

2. Press the ▲▼◄► buttons to move to a desired file, and then press the YELLOW (C) button to select it. Repeat this procedure to select additional files.

3. If you want to select all files, press the button, use the ▲▼ buttons to select Select All, and then press E. If you want to deselect all files, press the TOOLS button, select Deselect

All, and then press E.

Music TRACK 001 1 files selected 1/2 Page

㾎

TRACK 001 05:57

TRACK 003 04:07

TRACK 005 03:17

TRACK 007 03:47

TRACK 009 03:53

CD a Change Device

 Select Tools () Jump to Page ' Return

TRACK 002 04:27

TRACK 004 03:41

TRACK 006 03:35

TRACK 008 03:49

TRACK 010 03:45

TOOLS

HT-H5500_00W_30_50_50W-ENG_0402.indd 30HT-H5500_00W_30_50_50W-ENG_0402.indd 30 2014-04-02  1:07:502014-04-02  1:07:50

+ 230 hidden pages