Samsung HT-F6500W, HTF6500WZA User Manual

HT-F6500W

5.1CH Blu-ray™

Home Entertainment System

user manual

imagine the possibilities

Thank you for purchasing this Samsung product. To receive more complete service, please register your product at

www.samsung.com/register

Safety Information

Warning

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lighting flash and arrowhead within the triangle are warning signs alerting you to dangerous voltage inside the product.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING

• To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

FCC NOTES (for U.S.A)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on.

If interference is present, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect this equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

• This class B digital product meets all requirements of the Canadian Interference - Causing Equipment Regulations.

The exclamation point within the triangle is a warning sign alerting you to important instructions accompanying the product.

CLASS 1 LASER PRODUCT

This Compact Disc player is classified as a CLASS 1 LASER product. Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

Complies with 21CFR 1040.10 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007.

DANGER :

• VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM. (FDA 21 CFR)

CAUTION :

• CLASS 3B VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO THE BEAM (IEC 60825-1)

• THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVER AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT PRODUCTO LÁSER CLASE 1

2 English

Precautions

Important Safety Instructions

Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus (including AV receivers) that produce heat.

9. Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on

or pinched particularly at plugs, convenience receptacles, and the point where it exits the apparatus.

11. Only use attachments/accessories specified by the

manufacturer.

12. Use only with the cart, stand,

tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or

when unused for long periods of time.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been damaged in any way, such as when the powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Disc Storage & Management

• Holding Discs

- Fingerprints or scratches on a disc may reduce sound and picture quality or cause skipping.

- Avoid touching the surface of a disc where data has been recorded.

- Hold the disc by the edges so that fingerprints will not get on the surface.

- Do not stick paper or tape on the disc.

• Cleaning Discs

- If you get fingerprints or dirt on a disc, clean it with a mild detergent diluted in water and wipe with a soft cloth.

- When cleaning, wipe gently from the inside to the outside of the disc.

- Disc Storage

Do not keep in direct sunlight. Keep in a cool ventilated area. Keep in a clean protection jacket and store

vertically.

Handling Cautions

• Do not expose this apparatus to dripping or splashing. Do not put objects filled with liquids, such as vases, on the apparatus.

• To turn this apparatus off completely, you must pull the power plug out of the wall socket. Consequently, the power plug must be easily and readily accessible at all times.

• Do not touch the power plug with a wet hand. It can cause an electric shock.

• Do not plug multiple electric devices into the same wall socket. Overloading a socket can cause it to overheat, resulting in a fire.

• Before connecting other components to this product, be sure to turn them off.

• If you move your product suddenly from a cold place to a warm place, condensation may occur on the operating parts and lens and cause abnormal disc playback. If this occurs, unplug the product, wait for two hours, and then connect the plug to the power outlet. Then, insert the disc, and try to play back again.

01 Safety Information

English 3

Safety Information

• If the product makes an abnormal noise or produces a burning smell or smoke, turn off the power switch immediately and disconnect the power plug from the wall outlet. Then, contact the nearest customer service center for technical assistance. Do not use the product. Using the product as it is may cause a fire or an electric shock.

License

Manufactured under license from Dolby Laboratories.

Dolby, Pro Logic, and the double-D symbol are

trademarks of Dolby Laboratories.

Manufactured under a license from U.S. Patent No’s: 5,956,674, 5,974,380, 5,978,762, 6,487,535, 6,226,616, 7,212,872, 7,003,467, 7,272,567, 7,668,723, 7,392,195, 7,930,184, 7,333,929 and 7,548,853. DTS, DTS-HD, the Symbol, and DTS or DTS-HD and the Symbol together are registered trademarks & DTS Neo:Fusion is a trademark of DTS, Inc. ©2012 DTS, Inc. All Rights Reserved.

The terms HDMI and HDMI High-Definition Multimedia

Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

Oracle and Java are registered trademarks of Oracle and/or its affiliates. Other names may be trademarks of their respective owners.

This item incorporates copy protection technology that is protected by U.S. patents and other intellectual property rights of Rovi Corporation. Reverse engineering and disassembly are prohibited.

Blu-ray Disc™, Blu-ray™, and the logos are trademarks of Blu-ray Disc Association.

This product uses Cinavia technology to limit the use of unauthorized copies of some commerciallyproduced film and videos and their soundtracks. When a prohibited use of an unauthorized copy is detected, a message will be displayed and playback or copying will be interrupted. More information about Cinavia technology is provided at the Cinavia Online Consumer Information Center at http://www.cinavia.com. To request additional information about Cinavia by mail, send a postcard with your mailing address to: Cinavia Consumer Information Center, P.O. Box 86851, San Diego, CA, 92138, USA.” This product incorporates proprietary technology under license from Verance Corporation and is protected by U.S. Patent 7,369,677 and other U.S. and worldwide patents issued and pending as well as copyright and trade secret protection for certain aspects of such technology. Cinavia is a trademark of Verance Corporation. Copyright 2004-2010 Verance Corporation. All rights reserved by Verance. Reverse engineering or disassembly is prohibited.

- Open Source License Notice In the case of using open source software, Open

Source Licenses are available on the product menu.

Using the 3D Function

IMPORTANT HEALTH AND SAFETY INFORMATION FOR 3D PICTURES. Read and understand the following safety information before using the 3D function.

• Some viewers may experience discomfort while viewing 3D TV such as dizziness, nausea, and headaches. If you experience any such symptom, stop viewing 3D TV, remove the 3D Active Glasses, and rest.

• Watching 3D images for an extended period of time may cause eye strain. If you feel eye strain, stop viewing 3D TV, remove your 3D Active Glasses, and rest.

• A responsible adult should frequently check on children who are using the 3D function. If there are any reports of tired eyes, headaches, dizziness, or nausea, have the child stop viewing 3D TV and rest.

• Do not use the 3D Active Glasses for other purposes (such as general eyeglasses, sunglasses, protective goggles, etc.)

• Do not use the 3D function or 3D Active Glasses while walking or moving around. Using the 3D function or 3D Active Glasses while moving around may cause you to bump into objects, trip, and/or fall, and cause serious injury.

4 English

• If you want to enjoy 3D content, connect a 3D device (3D compliant AV receiver or TV) to the product’s HDMI OUT port using a high-speed HDMI cable. Put on 3D glasses before playing the 3D content.

• The product outputs 3D signals only through HDMI cable connected to the HDMI OUT port.

• As the video resolution in 3D play mode is fixed according to the resolution of the original 3D video, you can not change the resolution to your preference.

• Some functions such as BD Wise, screen size adjustment, and resolution adjustment may not operate properly in 3D play mode.

• You must use a high-speed HDMI cable for proper output of the 3D signal.

• Stay at least three times the width of the screen from the TV when watching 3D images. For example, if you have a 46 inch screen, stay 138 inches (11.5 feet) from the screen.

• Place the 3D video screen at eye level for the best 3D picture.

• When the product is connected to some 3D devices, the 3D effect may not function properly.

• This product does not convert 2D content into 3D.

• “Blu-ray 3D” and “Blu-ray 3D” logo are trademarks of the Blu-ray Disc Association.

may be reproduced or copied without the prior written permission of Samsung Electronics Co.,Ltd.

Contents

SAFETY INFORMATION

2 Warning 3 Precautions 3 Disc Storage & Management 3 Handling Cautions 4 License 4 Using the 3D Function 5 Copyright

GETTING STARTED

6 Disk and Format Compatibility 7 Logos of Discs the product can play 10 Accessories 11 Front Panel 11 Rear Panel 12 Remote Control

CONNECTIONS

14 Connecting the Speakers 16 Attaching the Toroidal Ferrite Core to the Power

Cord of the Wireless Receiver Module (SWA-6000)

17 Connecting to TV/External Devices 18 Connecting to a Network Router

SETTINGS

19 The Initial Settings Procedure 19 The Home Screen 19 Accessing the Settings Screen 20 Settings Menu Functions 24 Networks and the Internet 27 Upgrading Software

MEDIA PLAY

29 The All Content Screen 29 Playing Commercial Discs 29 Playing Files on a USB Device 30 Playing a Disc with User Recorded Content 30 Using the AllShare Network Function 31 Controlling Video Playback 34 Controlling Music Playback 38 Playing Photo Contents 39 Listening to Radio 39 Using the Special Effects Remote Control Buttons

NETWORK SERVICES

41 Logging In to Your Samsung Account 41 Before Using Movies & TV Shows or Apps 42 Using Movies & TV Shows 42 Using Apps 46 Screen Mirroring 46 Using the Web Browser 49 Linking your Internet Service Accounts to the

Product

49 BD-LIVE™

APPENDIX

50 Additional Information 53 Troubleshooting 56 Specifications

01 Safety Information

English 5

Getting Started

Disk and Format Compatibility

Disc types and content your Product can Play

Media Disc Type Details

Blu-ray Disc

3D Blu-ray Disc

VIDEO

MUSIC

PHOTO

| NOTES |

The product may not play certain CD-RW/-R and DVD-R because of the disc type or recording conditions.



If a DVD-RW/-R disc has not been recorded properly in DVD video format, it will not be playable.



Your product will not play content that has been recorded on a DVD-R at a bitrate that exceeds 10 Mbps.



Your product will not play content that has been recorded on a BD-R or USB device at a bitrate that exceeds 30



Mbps. Playback may not work for some types of discs, or when you use specific operations, such as angle change



and aspect ratio adjustment. Information about the discs is written in detail on the disc box. Please refer to this if necessary. When you play a BD-J title, loading may take longer than a normal title or some functions may perform slowly.



DVD-VIDEO, DVD-RW,

DVD-R, DVD+RW,

DVD+R

CD-RW/-R,

DVD-RW/-R,

BD-RE/-R

CD-RW/-R,

DVD-RW/-R,

BD-RE/-R

BD-ROM or BD-RE/-R disc recorded in the BD-RE format.

DVD-VIDEO, recorded DVD+RW/DVD-RW(V)/DVD-R/+R discs that have been recorded and finalized, or a USB storage media containing MKV, MP4 contents.

Music recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R discs or a USB storage media containing MP3 or WMA contents.

Photos recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R discs or a USB storage media containing JPEG contents.

Disc Types your Product cannot Play

• HD DVD

• DVD-ROM/PD/MV-Disc, etc

| NOTES |

This product may not respond to all operating commands because some Blu-ray Disc, DVD, and CD discs allow



specific or limited operation and provide only certain features during playback. Please note that this is not a defect in the product. Samsung cannot guarantee that this product will play every disc bearing the Blu-ray Disc, DVD or CD logo because



disc formats evolve, and problems and errors may occur during the creation of Blu-ray Disc, DVD, and CD software and/or the manufacture of discs. Please contact the SAMSUNG Customer Care Center at 1-800-726-7864 if you have questions or encounter



difficulty when playing Blu-ray Disc, DVD, or CD discs in this product. Also, refer to rest of this user manual for additional information on playback restrictions. Some commercial discs and DVD discs purchased outside your region may not play on this product.



6 English

• DVD-RAM

• Super Audio CD (except CD layer)

• DVD-RW(VR mode)

• CVD/CD-ROM/CDV/ CD-G/CD-I/LD (CD-Gs play audio only, not graphics.)

• 3.9 GB DVD-R Disc for Authoring.

Region Code

Both products and discs are coded by region. These regional codes must match for a disc to play. If the codes do not match, the disc will not play. The Region Number for this product is displayed on the rear panel of the product.

Disc Type

Blu-ray Disc

DVD-VIDEO

Region

Code

North America, Central

America, South America,

Korea, Japan, Taiwan, Hong

Kong and South East Asia.

Europe, Greenland, French

territories, Middle East, Africa,

Australia and New Zealand.

India, China, Russia, Central

and South Asia.

The U.S., U.S. territories and

Europe, Japan, the Middle

East, Egypt, South Africa,

Taiwan, Korea, the Philippines,

Indonesia, Hong Kong

Mexico, South America,

Central America, Australia,

New Zealand, Pacific Islands,

Area

Canada

Greenland

Caribbean

Logos of Discs the Product can Play

Blu-ray Disc 3D Blu-ray Disc

BD-LIVE Dolby

DTS

Java

NTSC broadcast system

in U.S.A, Canada, Korea,

Japan

02 Getting Started

Russia, Eastern Europe, India,

most of Africa, North Korea,

| NOTES |

If the Region number of a Blu-ray Disc/DVDs



does not correspond to the Region number of this product, the product cannot play the disc.

Mongolia

China

English 7

Getting Started

Supported Formats

Video File Support

File

Extension

*.avi

*.mkv

*.asf *.wmv *.mp4

*.3gp

*.vro

*.mpg

*.mpeg

*.ts

*.tp

*.trp

*.mov

*.flv

*.vob

*.svi

*.m2ts

*.webm

Container Video Codec Resolution

MPEG4 SP/ASP

AVI

MKV

ASF

MP4

3GP

MOV

FLV VRO VOB

PS TS

SVAF

WebM VP8 1920x1080

H.264 BP/

MP/HP

Motion JPEG

Microsoft

MPEG-4 v3

Window Media

Video v7, v8, v9

MPEG2

MPEG1

VP6 640x480

MVC -

1920x1080

(WMV v7,v8,

MSMPEG4 v3 :

1280x720)

Limitations

- Even when a file is encoded by a supported codec listed above, the file might not be played if its content is defective or corrupted.

- Normal playback is not guaranteed if the file's container information is wrong or the file itself is corrupted.

- Files having higher bit or frame rates than standard may stutter when played back.

- The seek (skip) function is not available if the file's index table is damaged.

- When you playback a file remotely through a network connection, video playback may stutter depending on the network speed.

- Some USB/Digital camera devices may not be compatible with the product.

Video decoder

- Supports up to H.264 Level 4.1 (except for FMO/ASO/ RS)

- Does not support VC1 AP L4

- Except for WMV v7, v8, MSMPEG4 v3, MVC, VP6 Below 1280 X 720: 60 frame max Above 1280 X 720: 30 frame max

- Does not support GMC 2 or higher

Frame rate

(fps)

6~30

24/25/30 60

6~30 20 Vorbis

- Supports SVAF Top/Bottom, Side by Side Only

- Supports BD MVC Spec Only

Bitrate (Mbps)

Audio Codec

Dolby Digital

LPCM

ADPCM

(IMA, MS)

AAC

HE-AAC

WMA

Dolby Digital

Plus

MPEG(MP3)

DTS

Audio decoder

- Supports WMA 10 Pro (Up to 5.1)

- Does not support WMA lossless audio.

- Supported ADPCM IMA, MS.

- Does not support ADPCM (A-Law, μ-Low)

- Does not support QCELP, AMR NB/WB

- Supports vorbis (Up to 2ch),

- Supports Dolby Digital Plus (Up to 7.1ch)

Comments

- MPEG4 : Supports up to GMC 1-Warping Point.

- H.264 : Supports up to BP/MP/HP Level 4.1.

- WMV : Supports V9, VC1 SP/MP/AP L3.

- MPEG1 : Does not support D-picture.

- MPEG2 : Supports up to Hight Profile High Level.

| NOTES |

Some MKV and MP4 format discs may not play,



depending on their video resolution and frame rate.

8 English

Music File Support

File

*.flac

Container

MP3

MPEG4

FLAC

OGG

WMA

wav

midi

ape

Extension

*.mp3

*.m4a *.mpa

*.aac

*.ogg

*.wma

*.wav

*.mid

*.midi

*.ape

Picture File Support

File Extension Type

*.jpg

*.jpeg

*.png

*.bmp

*.mpo

Audio

Codec

MPEG1

Audio

Layer 3

FLAC

Vorbis

WMA

JPEG

PNG

BMP

MPO

Support Range

AAC -

Supports up to

2ch

Supports up to

2ch

Supports WMA 10

Pro (Up to 5.1)

Does not support

WMA lossless

audio

Supports up to M2

profile

Does not

support LBR mode

wav -

midi type 0 and type 1

Does not support

ape

X13, NVT

Resolution

15360x8640

4096x4096

15360x8640

Notes on the USB connection

• Your product supports USB storage media, MP3 players, digital cameras, and USB card readers.

• The product does not support folder or file names longer than 128 characters.

• Some USB/digital camera devices may not be compatible with the product.

• Your product supports the FAT 16, FAT 32, and NTFS file systems.

• Connect USB devices directly to the product’s USB port. Connecting through a USB cable may cause compatibility problems.

• Inserting more than one memory device into a multi-card reader may cause the reader to operate improperly.

• The product does not support the PTP protocol.

• Do not disconnect a USB device during a “loading” process.

• The bigger the image resolution, the longer the image takes to display.

• This product cannot play MP3 files with DRM (Digital Rights Management) downloaded from commercial sites.

• Your product only supports video that is under 30fps (frame rate).

• Your product only supports USB Mass Storage Class (MSC) devices such as thumb drives and USB HDD. (HUB is not supported.)

• Certain USB HDD Devices, multi-card readers and thumb drives may not be compatible with this product.

• If some USB devices require excessive power, they may be limited by the circuit safety device.

• If playback from a USB HDD is unstable, provide additional power by plugging the HDD into a wall socket. If the problem continues, contact the USB HDD manufacturer.

• SAMSUNG is not responsible for any data file damage or data loss.

AVCHD (Advanced Video Codec High Definition)

• This product can play back AVCHD format discs. These discs are normally recorded and used in camcorders.

• The AVCHD format is a high definition digital video camera format.

• The MPEG-4 AVC/H.264 format compresses images with greater efficiency than the conventional image compressing format.

• Some AVCHD discs use the “x.v.Color” format. This product can play back AVCHD discs that use the “x.v.Color” format.

02 Getting Started

English 9

Getting Started

• “x.v.Color” is a trademark of Sony Corporation.

• “AVCHD” and the AVCHD logo are trademarks of Matsushita Electronic Industrial Co., Ltd. and Sony Corporation.

| NOTES |

Some AVCHD format discs may not play, depending



on the recording conditions. AVCHD format discs need to be finalized.



“x.v.Color” offers a wider color range than normal DVD



camcorder discs. Some MKV and MP4 format discs may not play,



depending on their video resolution and frame rate.

Accessories

Check for the supplied accessories below.

FUNCTION

TV SOURCE

RECEIVER

SLEEP

BD TV

123 4

56 809

DISC MENU TITLE MENU

POPUP

MUTE

TUNING

TV SOUND

VOL

/ CH

FULL SCREEN REPEAT

HOME

INFO

TOOLS

RETURN

EXIT

TUNER

MO/ST

MEMORY

ABCD

3D SOUND

S/W LEVEL

SMART SEARCH

(For Power cord)

HUB

SOUND

MANUAL

SUBTITLE

AUDIO

EFFECTPRESET

Toroidal Ferrite Core

(3301-000144)

(AH59-02538A)/

Batteries (AAA size)

(4301-000116)

Remote Control

Power Cable

(3903-000598)

User Manual

(AH68-02576A)

FM Antenna

(AH42-00021A)

Soft Cloth

(BN63-02368B )

 Figures and illustrations in this User Manual

are provided for reference only and may differ from actual product appearance.

10 English

Front Panel

5V 0.5A

HDMI OUT

HDMI IN

1 2

LAN

POWER

SPEAKERS OUT

CENTER

SUBWOOFER

FRONT

IMPEDANCE : 3

AUX IN FM ANT

OPTICAL

DIGITAL AUDIO IN

VACUUM TUBE AMP

VOLUME CONTROL

OPEN/CLOSE

PLAY/PAUSE

STOP

FUNCTION

DISPLAYDISC TRAY

02 Getting Started

REMOTE CONTROL SENSOR

POWER USB

| NOTES |

Cellular phones or mobile devices placed near the vacuum tube amp or electronic products placed on the top of the



product can cause audio noise or distortion. When the product is on, do not let children touch the product's surface. It will be hot.



To upgrade the product's software through the USB jack, you must use a USB flash drive.



When the product displays the Blu-ray Disc menu, you cannot start the movie by pressing the 6 button on the



product or the remote. To play the movie, you must select Play Movie or Start in the disc menu, and then press the

button.

If you use the Internet service or play the USB device contents on the TV, you cannot select the BD/DVD mode with



the FUNCTION button. Stop the playing contents on the TV first to select the BD/DVD mode.

Rear Panel

SPEAKER OUTPUT

COOLING FAN

POWER CORD HDMI OUT LAN TERMINAL EXTERNAL DIGITAL

* Connecting the FM Antenna

1. Connect the FM antenna supplied to the FM ANT Jack.

2. Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a wall or

other rigid surface.

| NOTES |

Maintain a minimum of 4 inches of clear space on all sides of the home theater to ensure adequate ventilation. Do



not obstruct the cooling fan or ventilation holes. This product does not receive AM broadcasts.



CONNECTORS HDMI IN AUX IN * FM ANTENNA

AUDIO IN (OPTICAL)

English 11

Getting Started

Remote Control

Tour of the Remote Control

Turn the product on and off.

To change to Television mode

and control the TV, press the TV

button.

To change to Home Theater mode

and control the Home Theater,

press the BD button.

Press numeric buttons to operate

options.

Press to view the disc menu.

Press to skip backwards or

forwards.

Press to stop/play a disc.

Cut off the sound temporarily.

Adjust the volume.

Press to move to the Home screen.

Press to see the full screen

on a TV.

Press to use the Tools menu.

Select on-screen menu items and

change menu values.

Return to the previous menu.

These buttons are used both for

menus on the product and also

several Blu-ray Disc functions.

Press to use Smart Hub.

Press to select MANUAL/PRESET

in the Tuner function.

Press to search contents.

Selects the disc Audio language.

FUNCTION

SOURCE

RECEIVER

BD TV

1 4 7

DISC MENU TITLE MENU

VOL

FULL SCREEN REPEAT

TOOLS

RETURN

ABCD

SMART SEARCH

HUB

MANUAL

AUDIO

SLEEP

3 56 809

POPUP

MUTE

TUNING

TV SOUND

/ CH

HOME

INFO

EXIT

TUNER

MO/ST

MEMORY

3D SOUND

S/W LEVEL

SOUND

SUBTITLE

EFFECTPRESET

Press to select the home theater's mode (HDMI1, AUX, BD/DVD, etc.).

or Press to select TV's video mode.

Set a Sleep time to shut off the product.

Press to open and close the disc tray.

Use to enter the Popup menu/Title menu.

Press to search backwards or forwards.

Press to pause a disc.

Search for active FM stations and to change channels.

Press to output the audio signal to the home theater speakers or the TV speaker. (See page 40)

Allows you to repeat a title, chapter, track or disc.

Use to display the playback information when playing a Blu-ray/DVD disc.

Press to exit the menu.

Use to set a preset radio frequency.

Select MONO or STEREO for radio broadcasts.

Press to apply the 3D sound effect.

Press to apply sound effects.

Use to adjust the level of the subwoofer.

Selects the disc subtitle language.

12 English

Installing batteries in the Remote Control

Battery size: AAA

| NOTES |

Make sure to match the “+” and “–” ends of the



batteries with the diagram inside the compartment. Assuming typical TV usage, the batteries last for about



one year. The remote control can be used up to approximately



23 feet (7 meters) from the product in a straight line.

Setting up the Remote Control

You can control certain functions of your TV with this remote control.

To operate a TV with the Remote Control

1. Press the TV button to set the remote control to TV

mode.

2. Turn on your TV.

3. While holding down the POWER button, enter the

code corresponding to your brand of TV.

• If there is more than one code listed for your TV in the table, enter one at a time to determine which code works.

• Example : For a Samsung TV While holding down the POWER button, use the number buttons to enter 00. If that does not work, try 15, then 16, etc.

4. If the TV turns off, the setting is complete.

• You can use the TV POWER, VOLUME, CHANNEL, and Numeric buttons (0~9).

| NOTES |

The remote may not be able to control some



functions, depending on your brand of TV. Also, the remote control may not work on some brands of TVs. The remote control will work with Samsung TVs by



default.

TV Control Codes

Brand Code

Admiral

(M.Wards)

A Mark 01, 15

Anam

AOC 01, 18, 40, 48

Bell & Howell

(M.Wards)

Brocsonic 59, 60

Candle 18

Cetronic 03

Citizen 03, 18, 25

Cinema 97

Classic 03

Concerto 18

Contec 46

Coronado 15

Craig 03, 05, 61, 82, 83, 84

Croslex 62

Crown 03

Curtis Mates 59, 61, 63

CXC 03

Daewoo

Daytron 40

Dynasty 03

Emerson

Fisher 19, 65

Funai 03

Futuretech 03

General Electric

(GE)

Hall Mark 40

Hitachi 15, 18, 50, 59, 69

Inkel 45

JC Penny 56, 59, 67, 86

JVC 70

KTV 59, 61, 87, 88

KEC 03, 15, 40

KMC 15

LG (Goldstar)

Luxman 18

LXI (Sears)

Magnavox

Marantz 40, 54

Matsui 54

MGA 18, 40

56, 57, 58

01, 02, 03, 04, 05, 06, 07, 08, 09, 10, 11, 12, 13, 14

57, 58, 81

02, 03, 04, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 32, 34,

35, 36, 48, 59, 90

03, 15, 40, 46, 59, 61, 64,

82, 83, 84, 85

06, 40, 56, 59, 66, 67, 68

01, 15, 16, 17, 37, 38, 39,

40, 41, 42, 43, 44

19, 54, 56, 59, 60, 62, 63,

65, 71

15, 17, 18, 48, 54, 59, 60,

62, 72, 89

Brand Code

Mitsubishi/MGA 18, 40, 59, 60, 75

MTC 18

NEC 18, 19, 20, 40, 59, 60

Nikei 03

Onking 03

Onwa 03

Panasonic

Radio Shack 17, 48, 56, 60, 61, 75

RCA/Proscan

Signature 2000

(M.Wards)

Soundesign 03, 40

Spectricon 01

Symphonic 61, 95, 96

Techwood 18

Dongyang 03, 54

06, 07, 08, 09, 54, 66,

Penney 18

Philco

Philips

Pioneer 63, 66, 80, 91

Portland 15, 18, 59

Proton 40

Quasar 06, 66, 67

Realistic 03, 19

Sampo 40

Samsung

Sanyo 19, 61, 65

Scott 03, 40, 60, 61

Sears 15, 18, 19

Sharp 15, 57, 64

Sony 50, 51, 52, 53, 55

SSS 18

Sylvania

Tatung 06

Teknika 03, 15, 18, 25

TMK 18, 40

Toshiba 19, 57, 63, 71

Vidtech 18

Videch 59, 60, 69

Wards

Yamaha 18

York 40

Yupiteru 03

Zenith 58, 79

Zonda 01

67, 73, 74

03, 15, 17, 18, 48, 54,

59, 62, 69, 90

15, 17, 18, 40, 48, 54,

62, 72

18, 59, 67, 76, 77, 78,

92, 93, 94

00, 15, 16, 17, 40, 43,

46, 47, 48, 49,

59, 60, 98

57, 58

18, 40, 48, 54, 59, 60,

15, 17, 18, 40, 48, 54,

60, 64

English 13

02 Getting Started

Connections

This section describes various methods of connecting the product to other external components. Before moving or installing the product, be sure to turn off the power and disconnect the power cord.

Connecting the Speakers

Position of the product

Place it on a stand or cabinet shelf, or

under the TV stand.

Subwoofer

Front (L)

Center

Product

Front (R)

Surround (R)

Selecting the Listening Position

The listening position should be located

about 2.5 to 3 times the TV's screen

size away from the TV. For example, if

you have a 46 inch screen, locate the

listening position 115 to 138 inches (9.6

to11.5 feet) from the screen.

Surround (L)

Place these speakers in front of your listening position, facing inwards (about 45°) toward you.

Front Speakers

Center Speaker

Surround Speakers

Subwoofer

* Surround speakers must be connected to the wireless receiver module.

Place the front speakers so that their tweeters will be at the same height as your ear. Align the front face of the front speakers with the front face of the center speaker or place them slightly in front of the center speakers.

It is best to install the Center Speaker at the same height as the front speakers. You can also install it directly over or under the TV.

Place these speakers to the side of your listening position. If there isn't enough room, place these speakers so they face each other. Position them about 2 to 3 feet (60 to 90cm) above your ear, facing slightly downward.

* Unlike the front and center speakers, the surround speakers are used mainly for sound

effects. Sound will not come from them all the time.

The position of the subwoofer is not so critical. Place it anywhere you like.

Wireless

Receiver Module

14 English

Speaker Components

HDMI OUT

SPEAKERS OUT

CENTER

SUBWOOFER

FRONT

IMPEDANCE : 3

SPEAKERS OUT

CENTER

SUBWOOFER

FRONT

IMPEDANCE : 3

Center

SWA-6000

03 Connections

Surround x 2Front x 2

Speaker Cable x 3 Subwoofer

Wireless Receiver

Module

Speaker

Cable x 2

Connecting The Speakers

1. Match each speaker cable bundle to the correct speaker by matching the color coded

plug on each bundle to the colored sticker on the bottom of each speaker.

2. To attach speaker wire to each speaker: a. Press down the red tab on the back of the speaker, insert the red wire, and then

release the tab.

b. Press down the black tab on the back of the speaker, insert the black wire, and then

release the tab.

3. Connect the speaker wire plugs from each speaker to the back of the product by

matching the colors of the speaker plugs to the colors of the speaker jacks.

4. Connect the left and right surround speakers to the wireless receiver module. Again, match the color of the plugs to the jacks on the wireless receiver module.

5. Plug the power cord of the wireless receiver module into a wall outlet.

6. Turn on the product. The product and wireless receiver module will now communicate with each other and you will

hear sound from the Surround speakers.

Front Speaker (R)

Subwoofer

Surround

Speaker (L)

Surround

Speaker (R)

Black

Front Speaker (L)

Center Speaker

Red

Wireless Receiver Module

* This product should be connected with the SWA-6000 only.

English 15

Connections

| CAUTION |

If you want to install the speakers on the wall, fasten screws or nails (not provided) firmly to the wall wherever you



want to hang a speaker, and then, using the hole in the rear of each speaker, carefully hang each speaker on a screw or nail. Do not let children play with or near the speakers. They could get hurt if a speaker falls.



When connecting the speaker wires to the speakers, make sure that the polarity (+/ –) is correct.



Keep the subwoofer speaker out of reach of children to prevent children from inserting their hands or alien



substances into the duct (hole) of the subwoofer speaker. Do not hang the subwoofer on the wall using the duct (hole).



The wireless receiving antenna is built into the wireless receiver module. Keep it away from water and moisture.



For optimal listening performance, make sure that the area around the wireless receiver module location is clear of



any obstructions. If you hear no sound from the wireless surround speakers, switch the mode to Dolby Pro Logic II.



In 2-CH mode, you will hear no sound from the wireless surround speakers.



| NOTES |

If you place a speaker near your TV set, the screen color may be distorted because of the magnetic field.



Place the wireless receiver module at the rear of the listening position. If the wireless receiver module is too close to



the product, sound from the speakers may be disrupted because of interference. If you use a device such as a microwave oven, wireless LAN Card, Bluetooth equipment or any other device that uses



the 2.4/5.8GHz frequencies near the product, sound from the speakers may be disrupted because of interference. The maximum transmission distance from the product to the wireless receiver module is about 33 feet (10m), but



may vary depending on your operating environment. If a steel-concrete wall or metallic wall is between the product and the wireless receiver module, the system may not operate at all, because the radio wave cannot penetrate metal. If the product doesn't make a wireless connection, you need to run an ID Set between the product and wireless



receiver module. With the product turned off, press "0""1""3""5" on the remote control. Turn on the wireless receiver module. Then, press and hold the “ID SET” button on the back of the wireless receiver module for 5 seconds, and then turn the product on.

Attaching the Toroidal Ferrite Core to the Power Cord of the Wireless Receiver Module (SWA-6000)

If you attach a Toroidal ferrite core to the power cord of the wireless receiver module, it will help to prevent RF interference from radio signals.

1. Pull the fixing tab of the Toroidal ferrite core to open it.

2. Make a loop twice in the wireless receiver module power cord.

3. Attach the Toroidal ferrite core to the wireless receiver module power

cord as the figure shows and press it until it clicks.

• Insert the ferrite core as close to the Wireless Receiver Module as possible.

16 English

Connecting to TV/External Devices

HDMI OUT

HDMI IN

1 2

LAN

AUX IN FM ANT

OPTICAL

DIGITAL AUDIO IN

OPTICAL OUT

AUDIO OUT

HDMI OUT

HDMI IN

1 2

LAN

POWER

SPEAKERS OUT

CENTER

SUBWOOFER

FRONT

IMPEDANCE : 3

AUX IN FM ANT

OPTICAL

DIGITAL AUDIO IN

HDMI OUTHDMI IN

Red

White

Method 1 Method 2 Method 3

External Devices

Connecting to a TV

Connect an HDMI cable (not supplied) from the HDMI OUT jack on the back of the product to the HDMI IN jack on your TV. If you have set the product's remote control to operate your TV, press the TV SOURCE button on the remote control and select HDMI as the external source of the TV.

Connecting to External Devices

To select the correct mode for an external device, press the FUNCTION button. Each time you press the button, the mode changes in this order : BD/DVD  D. IN  AUX  HDMI1  HDMI2  FM  BT

Method 1 HDMI IN : Connecting to an External Component with an HDMI Cable

Connect an HDMI cable (not supplied) from the HDMI IN jack on the back of the product to the HDMI OUT jack on your digital device.  Select the HDMI1 or HDMI2 mode.

Method 2 AUX IN : Connecting an External Analog Component

Using a RCA audio cable (not supplied), connect the AUDIO In jack on the product to the AUDIO Out jack on the external analog component.  Select the AUX mode.

• Be sure to match the colors on the cable plugs to the colors on the input and output jacks.

Method 3 OPTICAL : Connecting an External Digital Audio Component

Use to connect the digital audio output of digital signal components such as Cable Boxes and Satellite Receivers (SetTop-Boxes). Using a digital optical cable (not supplied), connect the Optical Digital Audio In jack on the product to the Digital Optical Out jack of the external digital device.

Select the D. IN mode.



| NOTES |

To see video from your Cable Box/Satellite receiver, you must connect its video output directly to your TV.



This system supports Digital sampling frequencies of 32 kHz or higher from external digital components.



This system supports only DTS and Dolby Digital audio. MPEG audio, a bitstream format, is not supported



English 17

03 Connections

Connections

Connecting to a Network Router

You can connect your product to your network router using one of the methods illustrated below.

Wired Network

1 2

HDMI IN

AUX IN FM ANT

LAN

OPTICAL

DIGITAL

AUDIO IN

Broadband

modem

Broadband

service

Broadband

service

SPEAKERS OUT

POWER

FRONT

IMPEDANCE : 3

CENTER

SUBWOOFER

HDMI OUT

Broadband modem

(with integrated router)

Router

| NOTES |

Your router or your Internet Service Provider's policies



may prevent the product from accessing Samsung's software update server. If this occurs, contact your Internet Service Provider (ISP) for more information. DSL users, please use a router to make a network



connection. To use the AllShare function, you must connect your



PC to your network as shown in the illustrations on the above. The connection can be wired or wireless.

Wireless Network

Wireless IP sharer

Broadband

service

| NOTES |

If your wireless IP router supports DHCP, this product



can use a DHCP or static IP address to connect to the wireless network. Set your wireless IP router to Infrastructure mode. Ad-



hoc mode is not supported. The product supports only the following wireless



security key protocols:

- WEP (OPEN/SHARED), WPA-PSK (TKIP/AES), WPA2-PSK (TKIP/AES)

Select a channel on the wireless IP router that is not



currently being used. If the channel set for the wireless IP router is currently being used by another device nearby, it will result in interference and communication failure. In compliance with the newest Wi-Fi certification



specifications, Samsung home theaters do not support WEP, TKIP, or TKIP-AES (WPS2 Mixed) security encryption in networks running in the 802.11n mode. Wireless LAN, by its nature, may cause interference,



depending on the operating conditions (AP performance, distance, obstacles, interference by other radio devices, etc).

18 English

+ 40 hidden pages