Samsung GS19VSSB User Manual

Driver Installation Pro

SyncMaster 710V/910V/510M/710M/910M/712V

ram Installation

Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.

Prohibited

Do not disassemble Disconnect the plug from the outlet

Do not touch Grounding to prevent an electric shock

Important to read and understand at all times

Power

When not used for extended periods of time, set your PC to DPMS.

If using a screen saver, set it to the active screen mode.

Do not use a damaged or loose plug.

z This may cause an electric shock or fire.

Do not pull the plug out by the wire nor touch the plug with wet hands.

z This may cause an electric shock or fire.

Use only a properly grounded plug and receptacle.

z An improper ground may cause electric shock or equipment damage.

Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage.

z Failure to do so may cause an electric shock or fire.

Do not connect too many extension cords or plugs to an outlet.

z This may cause a fire.

Installation

Put your monitor in a location with low humidity and a minimum of dust.

z An electric shock or fire could result inside the monitor.

Do not drop the monitor when moving it.

This may cause damage to the product or human body.

Place the monitor on a flat and stable surface.

z The monitor can cause injury by falling.

Set down the monitor carefully.

z It could be damaged or broken.

Do not place the monitor face down.

z The CDT surface may be damaged.

Installing a wall bracket must be done by a qualified professional.

z Installation by unqualified personnel may result in injury.

z Always use the mounting device specified in the owner's manual.

Leave a space for ventilation between the product and the wall.

z Poor ventilation may cause the interior temperature to rise and lead to a fire.

Clean

When cleaning the monitor case or the surface of the TFT-LCD, wipe with a slightly moistened, soft fabric.

Do not spray water or detergent directly on the monitor.

This may cause damage, electric shock or a fire.

Use the recommended detergent with a smooth cloth.

If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth.

z A dirty connector can cause an electric shock or fire.

Contact a Service Center or Customer Center for interior cleaning once a year.

Other

z Keep the product's interior clean. Dust which has accumulated in the interior

over an extended period of time may cause malfunction or a fire.

Do not remove cover (or back). No user serviceable parts inside.

z This may cause an electric shock or a fire.

z Refer servicing to qualified service personnel.

If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and

contact an authorized dealer or service.

z This may cause an electric shock or fire.

Be careful not to let water drip into the monitor or expose the monitor to moisture.

z This may cause malfunction, an electric shock or a fire.

Especially avoid operating the monitor near water or outdoors where it could be exposed to snow or rain.

If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord.

z The monitor may malfunction, causing an electric shock or a fire.

z Then contact the Service Center .

Keep the power off when there is thunder and lightening outside, or let the monitor remain unused for an extended period of time.

z The monitor may malfunction, causing an electric shock or a fire.

Do not try to move the monitor by pulling on the wire or the signal cable.

z This may cause a breakdown, electric shock or a fire due to damage to the

cable.

Do not move the monitor right or left by pulling only the wire or the signal cable.

z This may cause a breakdown, electric shock or a fire due to damage to the

cable.

Do not cover the vents on the monitor cabinet.

z Bad ventilation may cause a breakdown or fire.

Do not place water containers, chemical products or small metal objects on the monitor.

z This may cause malfunction, an electric shock or a fire.

z If a foreign substance enters the monitor, unplug the power cord and contact

the Service Center .

Do not use or store inflammable substances near the monitor.

z This may cause an explosion or fire.

Never insert anything metallic into the monitor openings.

z This may cause an electric shock, fire or injury.

Do not insert metal objects such as utensils, wire or drill bits, or things that catch fire easily, such as pieces of paper or matches, into the vents or the headphone or A/V ports on the monitor.

z This may cause malfunction, an electric shock or a fire.

z Always contact the Service Center if foreign substances/objects enter into the

monitor.

If you view a fixed screen for an extended period of time, residual image or blurriness may appear.

z Change the mode to energy save or set a screensaver to moving picture when

you need to be away from the monitor for an extended period of time.

Adjust the resolution and frequency to the levels appropriate for the model.

z Inappropriate resolution may cause undesirable picture quality.

17 inch - 1280 X 1024

Keep a proper distance between your eyes and the monitor screen.

z Sitting too close to the monitor on a continuous basis may damage eyesight.

To ease eye strain, take at least a five-minute break after every hour of using the monitor.

Do not use the monitor where it can be exposed to strong vibrations.

z Exposure to strong vibrations can be a fire hazard and shorten the life of the

monitor.

When moving the monitor, turn the power switch off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connecting to other devices, are disconnected before moving the monitor.

z Failure to disconnect a cable may damage it and lead to a fire or an electric

shock.

Unpacking

Monitor

SyncMaster 710V/910V/712V

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer.

Monitor Bottom Hanger

Manual

User's Guide, Monitor

Quick Setup Guide Warranty Card

Dirver, Natural Color

software, MagicTune™

software CD

Cable

Front

D-Sub Cable Power Cord

1. Menu button [ ]

2. MagicBright™ button [ ]

3. Power button [ ] / Power indicator

4. Brightness button [ ]

2,4. Adjust buttons [ ]

5. Enter button [ ]/ Auto button

Use this button to open the on-screen menu and exits from the menu screen or closes screen adjustment menu.

MagicBright™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Custom, Text, Internet, and Entertain. Each mode has its own pre-configured brightness value. You can easily select one of four settings by simply pressing MagicBright control buttons.

Use this button to turn the monitor on and off./ This light glows green during normal operation, and blinks green once as the monitor saves your adjustments.

When OSD is not on the screen, Push the button to adjust brightness.

Use this button to navigate and select menus or adjust the menu items in the menu screen.

Activate a highlighted menu item. / Use this button to auto adjustment direct access.

Rear

See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.

(The configuration at the back of the monitor may vary from product to product.)

1. Power port Connect the power cord for your monitor to the power port on the back of

2. D-sub 15-pin port Connect the signal cable to the 15-pin, D-sub connector on the back of your

See Connecting Your Monitor for further information regarding cable connections.

the monitor.

monitor.

Unpacking

Monitor

SyncMaster 510M/710M/910M

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer.

Monitor Bottom Hanger

Manual

User's Guide, Monitor

Quick Setup Guide Warranty Card

Dirver, Natural Color

software, MagicTune™

software CD

Cable

Front

D-Sub Cable Power Cord Audio Cable

1. Menu button [ ]

2. MagicBright™ button [ ]

Use this button for open the on-screen menu and exits from the menu screen or closes screen adjustment menu.

1) Text : Normal Brightness For documentations or works involving heavy text.

2) Internet : Medium Brightness For working with a mixture of images such as text and graphics.

3) Entertain : High Brightness For watching motion pictures such as a DVD or VCD.

4) Custom Although the values are carefully chosen by our engineers, the pre-

configured values may not be comfortable to your eyes depending on your taste.

If this is the case, adjust the Brightness and Contrast by using the OSD menu.

3. Power button [ ] / Power indicator

4. Volume button [ ]

2,4. Adjust buttons [ ]

5. Enter button [ ]/ Auto button

Rear

Use this button for turn the monitor on and off./ This light glows green during normal operation, and blinks green once as the monitor saves your adjustments.

When OSD is not on the screen, push the button to adjust volume.

Use this button for navigate and select menus or adjust the menu items in the menu screen.

Activate a highlighted menu item. / Use this button for auto adjustment direct access.

(The configuration at the back of the monitor may vary from product to product.)

1. Power port Connect the power cord for your monitor to the power port on the back of

2. D-sub 15-pin port Connect the signal cable to the 15-pin, D-sub connector on the back of your

the monitor.

monitor.

1. Headphone connection terminal [ ]

2. PC sound connection terminal

Connect the audio cable for your monitor to the audio port on the back of your computer.

See Connecting Your Monitor for further information regarding cable connections.

1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet.

2-1. Using the D-sub (Analog) connector on the video card.

Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.

2-2. Connected to a Macintosh.

Connect the monitor to the Macintosh computer using the D-SUB connection cable.

2-3. In the case of an old model Macintosh, you need to connect the monitor using a special Mac adaptor.

3. Turn on your computer and monitor. If your monitor displays an image, installation is complete.

Monitor Assembly

1. Monitor and Bottom

2. Monitor and Hanger

Attaching a base

This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.

A. Monitor B. Mounting interface pad

1. Turn off your monitor and unplug its power cord.

2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.

3. Remove the four screws and then remove the Stand from the LCD monitor.

lign the Mounting Interface Pad with the holes in the Rear Cover Mounting Pad and secure it with the

four screws that came with the arm-type base, wall mount hanger or other base.

z Internet web

site :

Windows ME

When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have.

Prepare a blank disk and download the driver program file at the Internet web site shown here.

http://www.samsung-monitor.com/ (Worldwide)

http://www.samsungusa.com/monitor (USA) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China)

1. Insert CD into the CD-ROM drive.

2. Click "Windows ME Driver".

3. Choose your monitor model in the model list, then click the "OK" button.

4. Click the "Install" button in the "Warning" window.

5. Monitor driver installation is completed.

Windows XP/2000

1. Insert CD into the CD-ROM drive.

2. Click "Windows XP/2000 Driver"

3. Choose your monitor model in the model list, then click the "OK" button.

4. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.

This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage

http://www.samsung-monitor.com/.

5. Monitor driver installation is completed.

Windows XP | Windows 2000 | Windows Me | Windows NT | Linux

Prepare a blank disk and download the driver program file at the Internet web site shown here.

z Internet web

site :

http://www.samsung-monitor.com/ (Worldwide)

http://www.samsungusa.com/monitor (USA) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China)

Microsoft® Windows® XP Operating System

1. Insert CD into the CD-ROM driver.

2. Click "Start" —> "Control Panel" then click the "Appearance and Themes" Icon.

3. Click "Display" icon and choose the "Settings" tab then click "Advanced..".

4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.

5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button.

6. Select "Don't search ,I will.." then click "Next" and then click "Have disk".

7. Click the "Browse" button then choose A:(D: Driver) and choose your monitor model in the model \ list and click the "Next" button.

8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.

This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage

http://www.samsung-monitor.com/

9. Click the "Close" button then click "OK" button continually.

+ 44 hidden pages