Samsung FE-N500WX/XAA-00 Installation Guide

Eeotro fringe

installation manual

the possibilities

ENGLISH

Thank you for purchasing this Samsung produc_.
Toreceivemore complete service, please register
your product a_

www.samsung.com/register

1-800-SAMSUNG(726-7864_

(_ 100% \

Recycled Pap_j

This manua_ _s maae with 1 00 _o recyc_eo paper.

Installation-USA DG68-00108E-01_EN.indd 1 2011-03-18 _u4:06:26

o

ABOUT THIS MANUAL

READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY.

Important note to the installer

* Read all instructions contained in these installation instructions before installing range.
* Remove all packing materials from the oven compartments before connecting the electrical supply

to the range.

* Observe all governing codes and ordinances.
* Be sure to leave these instructions with the consumer.

Important note to the consumer

Keep these instructions for the local electrical inspector's use.

* As when using any appliance generating heat, there are certain safety precautions you should follow.
* Be sure your range is installed and grounded properly by aqualified installer or service technician.

* Make sure the wall coverings around the range can withstand the heat generated by the range.
* To eliminate the need to reach over the surface elements, cabinet storage space above the elements

should be avoided.

* The range should not be placed on a base.

FOR YOUR SAFETY

A WARNING,fthe information in this manual is not followed exactly, afire or electrical

shock may result causing property damage, personal injury or death.

Aw_GWARNJN6 Before beginning the installation, switch power off at the service panel and
lock the service disconnecting means to prevent power from being switched on accidentally. When the

service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a
tag, to the service panel.

A.w_GWARNJN6 This appliance must be properly grounded.

ANTi=TIP DEVICE

TO REDUCETHE RISK OF TIPPING, THE APPLIANCE MUST BE SECURED BY PROPERLY

INSTALLINGTHE ANTI-TIP BRACKET PROVIDEDWITHTHIS APPLIANCE.

* ALL RANGES CAN TIP

• INSTALL ANTI=TIP BRACKET PACKED WITH RANGE

* INJURY TO PERSONS COULD RESULT

• SEE INSTALLATION MANUAL

Ifyou pull the range out and away from the wall for any reason, make sure the Anti-Tip bracket is

engaged when the range is pushed back against the wall.

WARNING

2 Before you begin

Installation-USADG68-00108E-01_EN.indd 2 2011-03-18 _u4:06:26

REMOVE PACKAGING

Remove packaging materials. Failure to remove packaging materials could result in damage to the
appliance.

PREPARE TOOLS & PARTS

What tools you will need

Drill

PhillipsScrewdriver

Adjustable Wrench

FlatScrewdriver Pencil Level

What's included with your range

Template Anti-Tip Bracket Screws (2 ea)

What's not included

4-Wire Cord or 3-Wire Cord

(UL Approved 40 or 50 AMP)

Pliers 1/4"Nut Driver

Strain Relief

(For Conduit Installation Only)

8

Preparing to install the range 3

Installation-USADG68-00108E-01_EN.indd 3 2011-03-18 004:06:26

CHECKING THE iNSTALLATiON SiTE

Clearances and dimensions

Toinstall the range, refer to the following figure.
For installation in CANADA, a Free-standing range is not to be installed closer than 12ram

from any adjacent surface,

i_k__CAU'_'_0N This range has been designed to comply with the maximum allowable wood

OAUTION

cabinet temperatures of 194°F. Make sure the wall covering, countertops and cabinets around the
range can withstand the heat (upto 194°F) generated by the range, if not, discoloration, delamination

or melting may occur.

A : Cabinet opening

30" For U.S.A,
30"-31" ForCANADA.

B : Acceptable electrical
outlet area

Minimum dimensions

_ IMPORTANTToeliminate the risk of burns or fire caused by reaching over heated surface

units, cabinet storage space located above the surface units should be avoided, if cabinet storage is to
be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of
5" beyond the bottom of the cabinets.

30"

* 30"

t

*'15"

* 30" minimum clearance between the top

of the cooking surface and the bottom of
an unprotected wood or metal cabinet;

or 24" minimum when the bottom of the
wood or metal cabinet is protected by not

less than 1/4"flame retardant millboard
covered with not less than no.28 MSG
sheet steel, 0.015" stainless steel, 0.024"
aluminum or 0.020" copper.

** 15" minimum between the countertop and

the adjacent cabinet bottom.

4 Prepad]g to i]sta the ra]ge

Installation-USADG68-OO108E-O1_EN.indd 4 2011-03-18 DI]4:06:27