Samsung DW80M9960US/AA-00, DW80M9960UG/AA-00, DW80M9550US/AA-00, DW80M9550UG/AA-00 Installation Guide

STOP

DW80M9* Series

Dishwasher

installation guide

These installation instructions are intended
for use by qualifi ed installers.

If you are having problems installing this dishwasher

U.S.A

Please call: 1-800-SAMSUNG (726-7864)

1-844-SAM-PAYS (726-7297)

for assistance: www.samsung.com/us/support

CANADA

Please call: 1-800-SAMSUNG (726-7864)
for assistance: www.samsung.com/ca/support (English)

www.samsung.com/ca_fr/support (French)

imagine the possibilities

Thank you for purchasing this Samsung product.

DW9900M-00183A-01_EN.indd 1DW9900M-00183A-01_EN.indd 1 1/2/2017 12:41:01 PM1/2/2017 12:41:01 PM

safety instructions

Throughout this manual, you will see Warning and Caution notes. The warnings,
cautions, and the important safety instructions that follow do not cover all
possible conditions and situations that may occur. It is your responsibility to use
common sense, caution, and care when installing, maintaining, and operating the
dishwasher. Samsung is not liable for damages resulting from improper use.

IMPORTANT SAFETY INSTRUCTIONS

What the icons and signs in this installation guide mean:

Hazards or unsafe practices that may result in severe personal injury or

WARNING

CAUTION

CAUTION

These warning signs are here to prevent injury to you and others.
Please follow them explicitly.
After reading this section, keep it in a safe place for future reference.

death.

Hazards or unsafe practices that may result in personal injury or property
damage.

To reduce the risk of fi re, explosion, electric shock, or personal injury when
using the dishwasher, follow these basic safety precautions:

Follow directions explicitly.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

WARNING

WARNING

State of California Proposition 65 Warning (US only)

This product contains chemicals known to the State of California to cause cancer and birth
defects or other reproductive harm.

Read all instructions before using the appliance.

Install and store the dishwasher inside, away from exposure to weather.

Do not install the dishwasher near electrical components. Keep the dishwasher away from
open fl ames.

CAUTION

Do not install the dishwasher on a carpet as this is a fi re hazard.

Do not install the dishwasher in a location where the water may freeze (where the
temperature falls below 32 ˚F (0 ˚C)). Frozen water in the hoses or pipes may damage the
dishwasher.

As with all equipment using electricity, water, and moving parts, potential hazards exist. To
safely operate this appliance, become familiar with its operation and exercise care when
using it.

The dishwasher must be properly grounded. Never connect it to an ungrounded outlet.

2_ safety instructions

DW9900M-00183A-01_EN.indd Sec1:2DW9900M-00183A-01_EN.indd Sec1:2 1/2/2017 12:41:05 PM1/2/2017 12:41:05 PM

Prior to removal of original dishwasher and the installation of your new unit, make sure to
switch o your circuit breaker. Do not connect the dishwasher until you have completed the
installation. Connecting the power cable is the last step when installing the dishwasher.

All wiring and grounding must be done in accordance with the electrical code applicable to
the region.

GROUNDING INSTRUCTIONS

For a permanently connected appliance:

This appliance must be connected to grounded metal, a permanent wiring system, or an
equipment-grounding conductor must be run with the circuit conductors and connected to
the equipment-grounding terminal or lead on the appliance.

The dishwasher is very heavy. Do not attempt to move or carry a dishwasher alone. Two or
more people are needed to move a dishwasher and avoid potential injuries.

If the power cable is damaged, it must be replaced by the manufacturer, a service agent or
similarly qualifi ed person in order to avoid a hazard.

CAUTION

Do not touch the power cable with wet hands.

CAUTION

Do not connect another appliance to the same power outlet as the dishwasher.

CAUTION

Make sure to use a new water supply line. Old lines are susceptible to breakage because
they become hardened and may cause property damage due to a water leakage.

The dishwasher must be connected to a hot water supply with a temperature between
120˚F (49 ˚C) ~ 149 °F (65 ˚C). This temperature range provides the best washing result and
shortest cycle time. Temperature should not exceed 149 ˚F (65 ˚C) to prevent damage to
dishes.

Ensure that the water supplied to the dishwasher does not freeze. Frozen water can
damage the hoses, valves, pump, or other components.

Certifi ed residential dishwashers are not intended for licensed food establishments.
(NSF/ANSI Standard 184 for Residential Dishwashers)

For a full list of safety information, please refer to the User Manual.

BEFORE INSTALLING THE DISHWASHER

WARNING

WARNING

DW9900M-00183A-01_EN.indd Sec1:3DW9900M-00183A-01_EN.indd Sec1:3 1/2/2017 12:41:05 PM1/2/2017 12:41:05 PM

Tip-Over Hazard

- Do not use the dishwasher until it is correctly installed.

- Do not push down on the door when it is open.

- Do not place excessive weight on the open door.

Electric Shock Hazard

Failure to follow these instructions can result in death, fi re, or electric shock:

- Electrically ground the dishwasher

- Connect the ground wire to the green ground connector in the junction box.

- Do not use an extension cord.

To reduce the risk of electric shock, fi re, or injury to persons, the installer must ensure that
the dishwasher is completely enclosed at the time of installation.

safety instructions _3

contents

PREPARING THE DISHWASHER

ENCLOSURE

5

INSTALLING THE DISHWASHER

6

SPECIFICATIONS

5 Product dimensions
5 Enclosure dimensions

6 STEP 1 Check the parts and tools
8 STEP 2 Select the best location for the

dishwasher

9 STEP 3 Check water supply requirements

and cautions

10 STEP 4 Check the electrical requirements

and cautions

11 STEP 5 Unpacking and inspecting the

dishwasher

12 STEP 6 Preparing the dishwasher
14 STEP 7 Placing the dishwasher and

connecting the hot water supply
line

15 STEP 8 Leveling the dishwasher
16 STEP 9 Securing the dishwasher
18 STEP 10 Connecting the drain hose
20 STEP 11 Wiring connections
21 STEP 12 Completing the installation

22

4_ contents

DW9900M-00183A-01_EN.indd Sec2:4DW9900M-00183A-01_EN.indd Sec2:4 1/2/2017 12:41:05 PM1/2/2017 12:41:05 PM

preparing the dishwasher enclosure

PRODUCT DIMENSIONS

Front view Rear view

Junction box

Side view

20½" (520 mm)

25" (636 mm)

ENCLOSURE DIMENSIONS

33⅞-35" (860-890 mm)

7

23

⁄8" (605 mm)

5¾" (140 mm)

2½" (60 mm)

2½" (60 mm)

You must arrange the water supply line, power cable
and drain hose in the space behind the dishwasher.

01 PREPARING THE DISHWASHER

This dishwasher is designed to be enclosed
on the top and on both sides by a standard
residential kitchen cabinet unit.

The installation enclosure must be clean and free

24" (610 mm)

minimum

34⅛-35⅓" (867-897 mm)

of any obstructions.

The enclosure must be at least 24 inches wide,
24 inches deep, and 34⅛ inches high.

24" (610 mm)

minimum

For the front door of the dishwasher to be fl ush
with the leading edge of the counter top, the
counter top must be at least 25 inches deep.

preparing the dishwasher enclosure _5

DW9900M-00183A-01_EN.indd Sec5:5DW9900M-00183A-01_EN.indd Sec5:5 1/2/2017 12:41:05 PM1/2/2017 12:41:05 PM

installing the dishwasher

Be sure that you or your installer follow these instructions closely so that the new
dishwasher works properly and that you are not at risk of injury when washing dishes.

STEP 1 CHECK THE PARTS AND TOOLS

Before starting on the installation, prepare all the necessary tools and parts required to install the
dishwasher. This will save installation time and simplify the installation process.

Parts required

Provided with the dishwasher. Check when you unbox the dishwasher in Step 5.

2 Installation brackets

4 Screws

(for the Kick plate &

SideBracketInstallation)

2 Screws

(for Top Bracket Installation)

Protective sticker Paper ruler

Kick Plate

Not provided

Power cable

Hot water supply line

Air gap Rubber connector

For the hot water supply line – We strongly recommend using ⅜" minimum O.D. copper tubing with a
compression fi tting or a fl exible stainless steel braided hot water supply line.
[Warning: Do not use plastic tubing. Plastic tubing can deteriorate over time and cause a leak inside
the tube fi tting.]
You also need a 90° Fitting with ¾" N.P.T. external pipe threads on one end and a fi tting sized to fi t
your hot water supply line (copper tubing/compression fi tting or braided hose) on the other.
For the power cable, we recommend a jacketed 12-2 cable with ground. Note that some local codes
may require the cable to have a BX style metal jacket.

Twist on wire

connector

90° Fitting

(¾")

Strain relief

Tube fi ttings Hose clamp

Electrical tape &

Standard duct tape

6_ installing the dishwasher

DW9900M-00183A-01_EN.indd Sec3:6DW9900M-00183A-01_EN.indd Sec3:6 1/2/2017 12:41:05 PM1/2/2017 12:41:05 PM

Tools required

Electric drill Safety glasses Gloves Flashlight

Adjustable wrench Wire stripper Pliers Nipper

Tape measure Pencil Phillips screwdriver Flat screwdriver

Tubing cutter Cutting knife Hole saw Level

Torx t20 Hex L-wrench

02 INSTALLING THE DISHWASHER

installing the dishwasher _7

DW9900M-00183A-01_EN.indd Sec3:7DW9900M-00183A-01_EN.indd Sec3:7 1/2/2017 12:41:06 PM1/2/2017 12:41:06 PM

installing the dishwasher

New installation

If the dishwasher is a new installation, most of the installation work must be done before the
dishwasher is moved into place.

Replacement

If the dishwasher is replacing an old dishwasher, you must check the exising dishwasher connections
for compatibility with the new dishwasher. Repace the existing connections as necessary.

STEP 2 SELECT THE BEST LOCATION FOR THE DISHWASHER

The following criteria are important to ensure the best location for the dishwasher:

- The location must have a solid fl oor that is able to support the weight of the dishwasher.

- The location must be near a sink with easy access to the water supply, drain, and electrical

outlet.

For the drain to operate properly, the dishwasher should be installed within 9.8 ft (3 m) of
the sink.

- The location must let you load your dishes into the dishwasher easily.

- The location must have su cient space for the dishwasher door to open easily and provide

enough space between the dishwasher and the cabinet sides (at least 0.1 in (2 mm)).

If the dishwasher is installed in a corner, ensure that the side of the dishwasher is more than
2 in. (50 mm) from the wall or cabinet to its right or left.

- The wall at the back must be free of obstructions.

If this is a new installation, follow these steps:

1. Using a 2 ½ inch hole saw, cut a hole into the side of the cabinet that holds the sink as

shown in Figure 1 below.

2. If the base inside the sink cabinet is raised above the kitchen fl oor and is higher than the

connections on the dishwasher, make a hole in the base inside the cabinet and in the cabinet
side as shown in Figure 1-2.

Depending on where your electrical outlet is, you may need to cut a hole in the opposite
cabinet side.

<Figure 1-1> <Figure 1-2>

The hole for the water supply line, drain hose and
power cables.

8_ installing the dishwasher

DW9900M-00183A-01_EN.indd Sec3:8DW9900M-00183A-01_EN.indd Sec3:8 1/2/2017 12:41:07 PM1/2/2017 12:41:07 PM

STEP 3 CHECK WATER SUPPLY REQUIREMENTS AND CAUTIONS

Hot Water

Supply Line

Power cable

4¼-6¼ in.
(110-160mm)

Inlet valve

• The hot water supply line pressure must be between 20~120 psi (140~830 kPa).

• Adjust the water heater to deliver water between 120 ˚F (49 ˚C) ~ 149 ˚F (65 ˚C).

- The dishwasher must be connected to a hot water supply between 120 ˚F (49 ˚C) ~ 149 ˚F

(65 ˚C). This temperature range provides the best washing result and shortest cycle time.
Temperature should not exceed 149 ˚F (65 ˚C) to prevent damage to dishes.

- Ensure that the water supply valve is turned o before connecting the hot water supply line to

the dishwasher.

- Seal the hot water supply line connections using tefl on tape or sealing compound to stop any

water leakage.

- The drain hose connected to the dishwasher must be run through the hole in the side wall so

it can be connected to the drain outlet of the sink. When you install the dishwasher, ensure
there is nothing on the drain hose and be careful not to tear it during the installation process.

<Figure 2>

Power cable

Hot Water

Supply Line

4¼-6¼ in.
(110-160mm)

02 INSTALLING THE DISHWASHER

Inlet valve

Dishwasher bottom

installing the dishwasher _9

DW9900M-00183A-01_EN.indd Sec3:9DW9900M-00183A-01_EN.indd Sec3:9 1/2/2017 12:41:07 PM1/2/2017 12:41:07 PM

Hot Water

Supply Line

2½-3½ in.

(64-89 mm)

Power cable channel

installing the dishwasher

STEP 4 CHECK THE ELECTRICAL REQUIREMENTS AND CAUTIONS

The electrical requirements for the dishwasher are as follows:

• In the United States, install in accordance with the National Electric Code/State and Municipal codes

and/or local codes.

• In Canada, install in accordance with the Canadian Electric Code C22.1-latest edition/Provincial and

Municipal codes and/or local codes.

• For cable direct connections.

- Use fl exible, armored or non-metallic sheathed, copper wire with a grounding wire that meets the
wiring requirements for your local codes and ordinances.

- Use the strain relief method provided with the wiring junction box or install a U.L.-listed/CSA-certifi ed
clamp connector to the wiring junction box. If using conduit, use a U.L.-listed/CSA-certifi ed conduit
connector.

<Figure 3>

2½-3½ in.

(64-89 mm)

Hot Water

Supply Line

Power cable channel

Dishwasher bottom

10_ installing the dishwasher

DW9900M-00183A-01_EN.indd Sec3:10DW9900M-00183A-01_EN.indd Sec3:10 1/2/2017 12:41:07 PM1/2/2017 12:41:07 PM

STEP 5 UNPACKING AND INSPECTING THE DISHWASHER

Unpack the dishwasher in an open area free of obstruction both around the packaging and overhead. We
recommend that you retain all of the packing materials until the dishwasher is fully installed and operational
to ensure you have removed all the product’s components from the packing materials prior to disposal.

Unpacking

1. Position the carton right-side-up with top arrows pointing

upwards.

2. Unbuckle or cut the straps securing the packaging.

3. Unpack the product packaging with care.

4. Put the straps and all of the packing materials from around

the dishwasher inspecting them for any signs of damage.

5. Locate and set aside the dishwasher's kick plate. The Kick

plate is attached to packing material of the dishwasher.

Kick plate

6. Lift the dishwasher from the packing tray, and then place it

on the fl oor.

ALWAYS LIFT THE DISHWASHER TO MOVE IT. Sliding
it over rough surfaces can damage the dishwasher’s feet

CAUTION

and sliding the feet over fi nished surfaces can, in some
cases, damage that fi nish or the underlying surface.

Use caution, and do not grab the upper air duct when
moving the dishwasher.

CAUTION

7. There is also packing inside the dishwasher that you may want to leave in place until the

dishwasher is installed.

8. DO NOT, under any circumstances, remove the sound-absorbent padding that surrounds

the exterior of the tub of the dishwasher.

Inspecting

Mechanical

1. Check the plastic base assembly to ensure that it is intact

2. Check the dishwasher’s feet to ensure they are in place and can be adjusted so you can level

and secure the dishwasher.

3. Check all the visible components on the bottom of the dishwasher to ensure they are intact

and secure.

4. Check the door latch, the operation of the hinges, and confi rm the door is properly secured

to the dishwasher.

02 INSTALLING THE DISHWASHER

installing the dishwasher _11

DW9900M-00183A-01_EN.indd Sec3:11DW9900M-00183A-01_EN.indd Sec3:11 1/2/2017 12:41:08 PM1/2/2017 12:41:08 PM

installing the dishwasher

A

Plumbing

1. Check the hot water connection on the back left-side of the base of the dishwasher.

The mounting plate should be secured to the back of the base, the threads inside the
connection should be smooth and shiny, and the area should be clean and free of any
debris.

2. Make sure the dishwasher and the accessories are all included in the package to ensure

these assemblies are not cracked and that all connections are secure.

3. Check the drain hose for any holes or deformities that could allow a water leak during

draining.

Electrical

1. Confi rm the junction box cover is secured to the junction box on the front right-side of the

base of the dishwasher.

2. Confi rm the electrical box was not damaged during shipping and that it is secured to the

base of the dishwasher.

Appearance

1. Confi rm there are no dents or scratches on the front of the dishwasher.

2. Check the edges of the doors for any roughness or cracking

3. Check the control panel to ensure it is clear and unscratched, and that all the control markers

are in their proper places.

Parts

1. Confi rm you have all the parts listed in Step 1 on page 6.

STEP 6 PREPARING THE DISHWASHER

1. Attach the protective sticker (A).

- To prevent damage, put the protective sticker on the bottom of the counter top as
shown in the picture.

Before putting the protective sticker, clean the counter top as shown in the picture.

For information, the length of the protective sticker is 26 inches (660 mm).

A

2. Ensure that the circuit breaker and water supply valve are turned o before proceeding with

the following steps.

Before you move or lay down the dishwasher for installation, make sure to adjust the height
of the legs so the legs are as short as possible. This prevents the legs from breaking.

CAUTION

Level the dishwasher by adjusting the height of the legs after you have the dishwasher in
place.

12_ installing the dishwasher

DW9900M-00183A-01_EN.indd Sec3:12DW9900M-00183A-01_EN.indd Sec3:12 1/2/2017 12:41:08 PM1/2/2017 12:41:08 PM

3. Then, insert the ¾" 90 degree fi tting into the inlet valve (see Figure 4-B). Tighten until the ¾"

Fitting is tight and pointing towards the water hose channel in the base of the dishwasher
(about 4 o'clock). Do not over tighten.

4. Cut the strings securing the drain hose to the back of the dishwasher. Roll-out the hose.

Make sure there are no kinks and that the hose is not bent at any extreme angles that could
constrict the fl ow of water.

5. Remove the junction box cover located at the bottom front right of the dishwasher using a

screwdriver, and then Install the strain relief (Figure 4 - C). Make sure to keep the junction box
cover you removed. It is used in Step 10, Wiring Connections.

6. If the countertop is made of wood or a material that is not damaged by drilling, attach the

two (2) Installation brackets that were supplied with the dishwasher using the supplied
screws (Figure 4 - A). They will be used in Step 8, Securing the Dishwasher.

If the drain hose needs to go to the right of the
dishwasher, secure the hose in the hose fi xer mounted
on the base. There are three positions the hose fi xer can
be installed at. To move the hose fi xer, gently squeeze
the fi xer, the turn to the left.

Make sure to secure on the arrow-marked area.

<Figure 4>

A

02 INSTALLING THE DISHWASHER

B

Junction box

Strain relief

90 º fi tting

C

CAUTION

Do not overtighten the 90˚ Fitting.
(Below 280 lb·in (31.6 N·m))
Doing so may damage the water
inlet valve and cause a water leak.

installing the dishwasher _13

DW9900M-00183A-01_EN.indd Sec3:13DW9900M-00183A-01_EN.indd Sec3:13 1/2/2017 12:41:08 PM1/2/2017 12:41:08 PM

built-in hook

Power cable

Hot Water Supply Line

Drain hose

Hot Water Supply Line

Elbow (¾" (9.5 mm))

Inlet valve

Junction box

installing the dishwasher

STEP 7 PLACING THE DISHWASHER AND CONNECTING THE HOT

WATER SUPPLY LINE

1. Adjust the three leveling legs at the bottom of the dishwasher after measuring the height

of the cabinet opening from under the countertop to the fl oor. (See Step 8, Leveling the
Dishwasher.)

2. Locate the hot water supply line and the power cable.

3. Place the dishwasher so that the hot water supply line is in the left side and the power cable

is in the right channel of the base of the dishwasher. The right-side channel for the power
cable has a built-in hook on the base so that you secure the power cable.

4. Pull the drain hose through the hole in the sink cabinet side wall. Keep it free of kinks.

5. Make sure the hot water supply line is not twisted, and then connect the hot water supply

line to the fi tting joint.

6. Slide the dishwasher carefully into the installation space. If possible, gently pull any excess

lengths of water supply line, drain hose, or power cable back as you move the dishwasher.
Get a second or third person to help you do this if necessary.

Do not place the dishwasher on the water supply line, drain hose, or power cable.

CAUTION

Also, make sure they are not folded or twisted.

Make sure the supply line is properly connected.
Wrap Tefl on tape around every connection to prevent water leaks.

CAUTION

<Figure 5>

Junction box

Drain hose

Hot Water Supply Line

Power cable

Inlet valve

Hot Water Supply Line

Elbow (¾" (9.5 mm))

Do not overtighten the 90˚ Fitting.
(Below 280 lb·in (31.6 N·m))
Doing so may damage the water inlet
valve and cause a water leak.

CAUTION

built-in hook

Make sure the dishwasher is positioned to the center.

14_ installing the dishwasher

DW9900M-00183A-01_EN.indd Sec3:14DW9900M-00183A-01_EN.indd Sec3:14 1/2/2017 12:41:08 PM1/2/2017 12:41:08 PM

STEP 8 LEVELING THE DISHWASHER

1. Open the door and place the level against the top of the

tub on the inside and check if the the dishwasher is level.
If it is not level, rotate the leveling legs at the bottom front
of the dishwasher until the dishwasher is level.
See the fi rst note below for instructions on adusting the
height of the front legs.

2. Use the level to check if the dishwasher is level front to

back, as shown in the fi gure to the right.
If the dishwasher is not level front to back, adjust the height
of the rear leg until the dishwasher is level.
See the second note below for instructions on adusting the
the rear leg.

3. Open the door of the dishwasher and check if both the tub

and door clearances are correct.
If not, rotate the leveling legs on the bottom front of the
dishwasher.
You can aslo check this by placing a level against an inside
front vertical surface of the tub.

If the leveling legs are rotated to the right (counter
clockwise), they are loosened and the front of the
dishwasher is raised. If they are rotated to the left
(clockwise), they are tightened and the front of the
dishwasher is lowered.

You can adjust the leveling legs by a max of 1
However, leveling up to the max height is not
recommended.

To adjust the height of a rear leg, turn the T210 Torx (at
the front of the base) to the left to raise the back of the
dishwasher using the proper tool (T20 Torx).

6

02 INSTALLING THE DISHWASHER

/32"

Before you move the dishwasher for installation, make sure to adjust the height of the

CAUTION

legs so the legs are as short as possible. This prevents the legs from breaking. Level the
dishwasher by adjusting the height of the legs after you have the dishwasher in place.

The dishwasher can leak if it’s tilted by more than 1 degree.

CAUTION

If the product is installed unleveled or with the leg missing, the door may not close
completely, causing a leak of steam or water.

installing the dishwasher _15

DW9900M-00183A-01_EN.indd Sec3:15DW9900M-00183A-01_EN.indd Sec3:15 1/2/2017 12:41:09 PM1/2/2017 12:41:09 PM