Samsung DVD-U8800 User Manual

DVD Player

DVD-U8800

www.samsung.com

AK68-01509T

PRECAUTIONS

1. Setting up

- Refer to the identification label located on the rear of your player for its proper operating voltage.

- Install your player in a cabinet with adequate ventilation holes. (7~10cm) Do not block ventilation holes on any of the components for air circulation.

- Do not push the disc tray in by hand.

- Do not stack components.

- Be sure to turn all components off before moving the player.

- Before connecting other components to this player, be sure to turn them off.

- Be sure to remove the disc and turn off the player after use, especially if you are not going to use it for a long time.

- The mains plug is used as a disconnect device and shall stay readly operable at any time.

2. For your safety

- This product utilizes a laser. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

- Do not open covers and do not repair yourself. Refer servicing to qualified personal.

3. Caution

- Your player is not intended for industrial use but for domestic purposes. Use of this product is for personal use only.

- Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vese, shall be placed on the apparatus.

- Exterior influences such as lightning and static electricity can affect normal operation of this player. If this occurs, turn the player off and on again with the POWER button, or disconnect and then reconnect the AC power cord to the AC power outlet. The player will operate normally.

- When condensation forms inside the player due to sharp changes in temperature, the

player may not operate correctly. If this occurs, leave the player at room temperature until the inside of the player becomes dry and operational.

4. Disc

- Do not clean disc using record-cleaning sprays, benzene, thinner, or other volatile solvents that may cause damage to the disc surface.

- Do not touch the disc’s signal surface. Hold by the edges or by one edge and the hole in the center.

- Wipe the dirt away gently; never wipe a cloth back and forth over the disc.

5. Environmental info

- The battery used in this product contains chemicals that are harmful to the environ ment.

- So, dispose of batteries in the proper man ner, according to federal, state, and local regulations.

The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are granted for commercial use. The license does not cover any product unit other than this product unit and the license does not extend to any unlicensed product unit or process conforming to ISO/OUR 11172-3 or ISO/OUR 13818-3 used or sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode audio files conforming to the ISO/OUR 11172-3 or ISO/OUR 13818-3. No rights are granted under this license for product features or functions that do not conform to the ISO/OUR 11172-3 or ISO/OUR 13818-3.

CAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER THAN SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

BEFORE

ARTT

YOU

ABLE OF

TTABLE OF

CONTENTS

Accessories

Remote Control Batteries for Remote

Control (AAA Size)

User’s Manual

Install Batteries in the Remote control

1. Open the battery cover on the back of the remote control.

2. Insert two AAA batteries. Make sure that the polarities (+ and -) are aligned correctly.

3. Replace the battery cover.

If remote control doesn’t operate properly:

- Check the polarity + - of the batteries (Dry-Cell)

- Check if the batteries are drained.

- Check if remote control sensor is blocked by

obstacles.

- Check if there is any fluorescent lighting nearby.

Video/Audio

Cable

Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Setup

General Features . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Disc Type and Characteristics . . . . . . . . . . . . . . . . 5

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Tour of the Remote Control . . . . . . . . . . . . . . . . . . 8

Connections

Choosing a Connection . . . . . . . . . . . . . . . . . . . . . 9

Basic Functions

Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Using the Search and Skip Functions . . . . . . . . . 15

Using the Display Function . . . . . . . . . . . . . . . . . 15

Using the Disc and Title Menu . . . . . . . . . . . . . . 16

Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Advanced Functions

Adjusting the Aspect Ratio (EZ View) . . . . . . . . . 17

Selecting the Audio Language . . . . . . . . . . . . . . . 18

Selecting the Subtitle Language. . . . . . . . . . . . . . 18

Changing the Camera Angle . . . . . . . . . . . . . . . . 19

Using the Bookmark Function . . . . . . . . . . . . . . . 19

Using the Zoom Function . . . . . . . . . . . . . . . . . . . 20

Clips Menu for MP3/WMA/JPEG/MPEG4/

CD Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . . 20

MP3/WMA/CD Audio Playback. . . . . . . . . . . . . . . 21

MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . . . . . 21

Playing Media files Using the USB

Host feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

CD Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Picture CD Playback. . . . . . . . . . . . . . . . . . . . . . . 24

Changing Setup Menu

Using the Setup Menu . . . . . . . . . . . . . . . . . . . . . 25

Setting Up the Language Features . . . . . . . . . . . 25

Setting Up the Audio Options . . . . . . . . . . . . . . . . 26

Setting Up the Display Options . . . . . . . . . . . . . . 27

Setting Up the Parental Control . . . . . . . . . . . . . . 28

Reference

Firmware upgrade . . . . . . . . . . . . . . . . . . . . . . . . 30

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 31

USB Host feature supported products . . . . . . . . . 32

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

English

SETUP

General Features

Excellent Sound

Dolby Digital, a technology developed by Dolby Laboratories, provides crystal clear sound reproduction.

Screen

Both regular and widescreen(16:9) pictures can be viewed.

Slow Motion

An important scene can be viewed in slow motion.

Parental Control (DVD)

The parental control allows users to set the level necessary to prohibit children from viewing harmful movies such as those with violence, adult subject matter, etc.

Various On-Screen Menu Functions

You can select various languages (Audio/Subtitle) and screen angles while enjoying movies.

Progressive Scan

Progressive scanning creates an improved picture with double the scan lines of a conventional interlaced picture.

EZ VIEW (DVD)

Easy View enables picture adjustment to match your TV's screen size (16:9 or 4:3).

Digital Photo Viewer (JPEG)

You can view Digital Photos on your TV.

Repeat

You can repeat a song or movie simply by pressing the REPEAT button.

MP3/WMA

This unit can play discs created from MP3/WMA files.

MPEG4

This unit can play MPEG4 formats within an avi file.

CD Ripping

This feature lets you to copy audio files from dics to USB device into MP3 format. (only audio CD (CD DA)

Note

- Discs which cannot be played with this player.

• DVD-ROM • DVD-RAM

• CD-ROM • CDV

• CDI • CVD

• CDGs play audio only, not graphics.

- Ability to play back may depend on recording conditions.

• DVD-R, +R

• CD-RW

• DVD+RW, -RW (V mode)

- The unit may not play certain CD-R, CD-RW and DVD-R due to the disc type or recording conditions.

COPY PROTECTION

Many DVD discs are encoded with copy protection. Because of this, you should only connect your DVD player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copyprotected DVD discs.

This product incorporates copyright protection technology that is protected by methods claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be auzthorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

PROGRESSIVE SCAN OUTPUTS (525p)

“CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE, IN CASE OF 525 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS REGARDING YOUR TV SET COMPATIBILITY WITH THIS MODEL 525p DVD PLAYER, PLEASE CONTACT SAMSUNG'S CUSTOMER SERVICE CENTER.”

Disc Type and Characteristics

This DVD player is capable of playing the following types of discs with the corresponding logos:

Disc Types (Logos)

DVD

VIDEO-CD

AUDIO-CD

Disc Markings

Play Region Number

PAL

STEREO

DIGITAL

SOUND

PAL broadcast system in U.K, France, Germany, etc.

Dolby Digital disc

Stereo disc

Digital Audio disc

Recording Types Disc Size Max. Playing Time Characteristics

- DVD contains excellent sound and video due to Dolby Digital and MPEG2 system.

- Various screen and audio functions can be easily selected through the onscreen menu.

- Video with CD sound, VHS quality & MPEG-1 compression technology.

- CD is recorded as a Digital Signal with better audio quality, less distortion and less deterioration of audio quality over time.

Audio

Video

Audio

Video

Audio

12 Cm

8 Cm

12 Cm

8 Cm

12 Cm

8 Cm

Single-sided 240 min.

Double-sided 480 min.

Single-sided 80 min.

Double-sided 160 min.

74 min.

20 min.

74 min.

20 min.

Region Number

Both the DVD player and the discs are coded by region. These regional codes must match in order for the disc to play. If the codes do not match, the disc will not play.

The Region Number for this player is described on the rear panel of the player.

English

DTS disc

MP3 disc

You must only insert one DVD disc at a time. Inserting two or more discs will not allow to play them back and it may cause damage to the DVD player.

DivX Certification

DivX, DivX Certified, and associated logos are trademarks of DivXNetworks, Inc and are used under license

Description

Front Panel Controls

1. STANDBY/ON ( )

When STANDBY/ON is pressed on, the indicator goes

out and the player is turned on.

2. STANDBY indicator

When the unit is first plugged in, this indicator lights.

3. DISC TRAY

Place the disc here.

4. OPEN/CLOSE ( )

Press to open and close the disc tray.

5. DISPLAY

Operation indicators are displayed here.

6. SKIP ( / ) SEARCH

Allow you to search forward/backward through

a disc. Use to skip the title, chapter or track.

7. STOP ( )

Stops disc play.

8. PLAY/PAUSE ( )

Begin or pause disc play.

9. USB Host

Connect digital still camera, MP3 player, memory stick,

Card reader, or other removable storage devices.

Front Panel Display

Total playing time/Displays various messages concerning operations such as PLAY, STOP, LOAD ...

nodSC: No disc loaded. OPEn: The disc tray is open. LOAd: Player is loading disc information.

Rear Panel

English

1. DIGITAL AUDIO OUT JACKS

- Use either an coaxial digital cable to connect to a compatible Dolby Digital receiver.

- Use either an coaxial digital cable to connect to an A/V Amplifier that contains a Dolby Digital, MPEG2 or DTS decoder.

2. COMPONENT VIDEO OUT JACKS

- Use these jacks if you have a TV with Component Video in jacks. These jacks provide P video.

- If P-SCAN Video Output is selected in Setup Menu, progressive scan mode will work.

- If I-SCAN Video Output is selected in Setup Menu, interlaced scan mode will work.

, PBand Y

3. AUDIO OUT JACKS

4. VIDEO OUT JACK

- Connect to the Audio input jacks of your television or audio/video receiver.

- Use a video cable to connect to the Video input jack on your television.

Note

- Consult your TV User’s Manual to find out if your TV supports Progressive Scan.

If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the TV’s menu system.

- See pages 27 to get more information on how to use the setup menu.

Tour of the Remote Control

5 6

8 9

13 14

1. DVD POWER Button

Turns the power on or off.

2. NUMBER Buttons

3. ZOOM Button/(-/--)

Enlarge DVD Picture / Use this button to select the

channel of TV program by inserted the channel number

(TV mode).

4. SEARCH Buttos (

Allow you to search forward/backward through a disc.

5. VIDEO SEL. Button

Selects video output formats.

)

15 16

19 20

6. TV VOL (+, -) Buttons

Control volume.

7. SKIP Buttons (

Use to skip the title, chapter or track.

8. STOP Button ( )

9. MENU Button

Brings up the DVD player’s menu.

10. ENTER/

This button functions as a toggle switch.

11. EZ VIEW Button

The aspect ratio of a picture can easily be adjusted

according to the screen size of your TV (16:9 or 4:3).

12. DISC MENU Button

Brings up the Disc menu.

13. OPEN/CLOSE ( ) Button

To open and close the disc tray.

14. AUDIO Button

Use this button to access various audio functions on a disc.

15. DVD Button

Press this button when you use a DVD player.

16. TV Button

Press this button to operate TV.

17. REPEAT A-B Button

Allows you to repeat A-B disc.

18. STEP Button/TV Source

Advances play one frame at a time / Press this button to

select an available TV source (TV mode).

19. SUBTITLE Button

20.

TV CH ( , ) Buttons

Channel selection.

21. PLAY/PAUSE Button ( )

Begin/Pause disc play.

22. RETURN Button

Returns to a previous menu.

23. INFO Button

Displays the current disc mode.

24. CANCEL Button

Use to remove menus or status displays from the

screen.

25. USB Button

26. REPEAT Button

Allows you to repeat play a title, chapter, track, or disc.

/,¦¦/

Buttons

)

CONNECTIONS

Choosing a Connection

The following shows examples of connections commonly used to connect the DVD player with a TV and other components.

Before Connecting the DVD Player

- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.

- Refer to the user’s manual of the additional components you are connecting for more information on those particular components.

Connection to a TV (For Video)

Using video/audio cables, connect the VIDEO (yellow)/AUDIO (red and white) OUT terminals on the rear of the DVD player to the VIDEO (yellow)/AUDIO (red and white) IN terminals of TV.

WHITE

English

Turn on the DVD player and TV..

Press the TV/VIDEO button on the TV's remote control to select Video.

RED

Audio Cable

YELLOW

Video Cable

WHITE

RED

YELLOW

Note

- Noise may be generated if the audio cable is too close to the power cable.

- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 12 to 13)

- The number and position of terminals can vary depending on your TV set. Please refer to the user's manual of the TV.

- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal of the DVD player.

Connection to a TV (Interlace)

- Connecting to your TV using Component video cables.

- You will enjoy high quality and accurate color reproduction images. Component video separates the picture element into black and white(Y), blue(PB), red(PR) signals to present clear and clean images. (Audio signals are delivered through the audio output.)

Using component video cables (not included), connect the COMPONENT VIDEO OUT terminal on the rear of the DVD player to the COMPONENT IN terminal of TV.

Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD player to the

WHITE

GREEN

BLUE

AUDIO (red and white) IN terminals of TV. Turn on the

DVD player and TV.

RED

Audio Cable

RED

Component cable (not included)

Press the input selector on your TV remote control until the Component signal from the DVD player appears on the TV screen.

RED

WHITE

BLUE

RED

GREEN

Set the Video Output to I-SCAN in the Display Setup menu. (See pages 27-28)

Note

- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 12 to 13)

- The component terminal of TV can be marked by “R-Y, B-Y, Y” or “Cr, Cb, Y” instead of “P depending on the manufacturer. The number and position of terminals can vary depending on the TV set. Please refer to the user's manual of the TV.

, PB, Y”

Connection to a TV (Progressive)

Using component video cables (not included), connect the COMPONENT VIDEO OUT terminal on the rear of the DVD player to the COMPONENT IN terminal of TV.

Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of TV. Turn on the

DVD player and TV.

Press the input selector on your TV remote control until the Component signal from the DVD player appears on the TV

WHITE

RED

Audio Cable

RED

WHITE

RED

BLUE

GREEN

BLUE

RED

GREEN

Component cable (not included)

screen.

Set the Video Output to P-SCAN in the Display Setup menu. (See pages 27-28)

To see the progressive video output,

- Consult your TV User’s Manual to find out if your TV supports Progressive Scan. If Progressive

You need a TV set supporting the progressive scan

Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the TV’s

input function. And you have to set up the TV

menu system.

- Depending on your TV, the connection method may differ from the illustration above.

English

Note

- What is "Progressive Scan"? Progressive scan has twice as many scanning lines as the interlace output method has. Progressive scanning method can provide better and clearer picture quality.

Connection to an Audio System (2 Channel Amplifier)

Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of the Amplifier.

Using the video signal cable(s), connect the VIDEO, COM- PONENT OUT terminals on the rear of the DVD player to

the VIDEO, COMPONENT IN terminal of your TV as described on pages 9 to 11.

WHITE

RED

Turn on the DVD player, TV, and Amplifier.

Audio Cable

WHITE

RED

Press the input select button of the Amplifier to select external input in order to hear sound from the DVD player. Refer to your Amplifier's user manual to set the Amplifier's audio input.

Note

- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause

damage to the speakers and your ears.

- Please set the audio in the menu screen according to the Amplifier. (See pages 26-27)

- The position of terminals can vary depending on the Amplifier.

Please refer to the user's manual of the Amplifier.

Connection to an Audio System (Dolby digital, MPEG2 or DTS Amplifier)

If using a coaxial cable (not included), connect the DIGITAL AUDIO OUT (COAXIAL) terminal on the rear of the

DVD player to the DIGITAL AUDIO IN (COAXIAL) terminal of the Amplifier.

Using the video signal cable(s), connect the VIDEO, COM-

PONENT OUT terminals on the rear of the DVD player to

the VIDEO, COMPONENT IN terminal of your TV as

described on pages 9 to 11

Turn on the DVD player, TV, and Amplifier.

Coaxial Cable (not included)

Press the input select button of the Amplifier to select external input in order to hear sound from the DVD player. Refer to your Amplifier's user manual to set the Amplifier's audio input.

Note

- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause

damage to the speakers and your ears.

- Please set the audio in the menu screen according to the Amplifier. (See pages 26-27)

- The position of terminals can vary depending on the Amplifier.

Please refer to the user's manual of the Amplifier.

English

BASIC

FUNCTIONS

Playing a Disc

Before Play

- Turn on your TV and set it to the correct Video Input by pressing TV/VIDEO button on the TV remote control.

- If you connected an external Audio System, turn on your Audio System and set it to the correct Audio Input.

After plugging in the player, the first time you press the DVD POWER button, this screen comes up: If you want to select a language, press a NUMBER button. (This screen will only appear when you plug in the player for the first time.) If the language for the startup screen is not set, the settings may change whenever you turn the power on or off. Therefore, make sure that you select the language you want to use. Once you select a menu language, you can change it by pressing the button on the front panel of the unit for more than 5 seconds with no disc in the unit. Then the SELECT MENU LANGUAGE window appears again where you can reset your preferred language.

Press 1 for English

Playback

1. Press the OPEN/CLOSE ( ) button. The STANDBY indicator light goes out and the tray opens.

2. Place a disc gently into the tray with the disc’s label facing up.

3. Press the PLAY/PAUSE ( ) button or OPEN/ CLOSE ()button to close the disc tray.

When you stop disc play, the player remembers

where you stopped, so when you press PLAY/PAUSE ( ) button again, it will pick up where you left off.

bOK2v—U È«d

4. Stopping Play Press the STOP ( ) button during play.

5. Removing Disc

Press the OPEN/CLOSE ( ) button.

6. Pausing Play Press the PLAY/PAUSE ( ) or STEP button on the remote control during play.

- Screen stops, no sound. To resume, press the PLAY/PAUSE ( )

button once again.

7. Step Motion Play (Except CD) Press the STEP button on the remote control during play.

- Each time the button is pressed, a new frame will appear.

- No sound is heard during STEP mode.

- Press the PLAY/PAUSE ( ) button to resume normal play.

- You can only perform step motion play in the forward direction.

8. Slow Motion Play Press the SEARCH (/) button to choose the play speed between 1/8, 1/4 and 1/2 of normal during PAUSE or STEP mode.

- No sound is heard during slow mode.

- Press the PLAY/PAUSE ( ) button to resume

normal play.

Note

- If the player is left in the stop mode for more than one minute without any user interaction, a screen saver will be activated. Press the PLAY/PAUSE ( ) button to resume normal play.

- If the player is left in the stop mode for more than about 30 minutes, the power will automatically shut off.(Automatic Power-Off Function)

- If the player is left for about 5 minutes in pause mode, it will stop.

- This ( ) icon indicates an invalid button press.

Using the Search and Skip

Title

Chapter

Time

Audio

Subtitle

Shortcut

Functions

During play, you can search quickly through a chapter or track, and use the skip function to jump to the next selection.

Searching through a Chapter or Track

During play, press the SEARCH ( or ) button on the remote control for more than 1 second.

2X, 4X, 64X, 128X

DVD

4X, 8X

VCD

2X, 4X, 8X

Note

- The speed marked in this function may be different from the actual playback speed.

- No sound is hearing during search mode

(Except CD).

Skipping Tracks

During play, press the SKIP ( or ) button.

- When playing a DVD, if you press the SKIP ( ) button, it

moves to the next chapter. If you press the SKIP ( )

button, it moves to the beginning of the chapter. One more

press makes it move to the beginning of the previous

chapter.

- When playing a VCD 2.0 in Menu Off mode, or a VCD 1.1

or a CD, if you press the SKIP ( ) button, it moves to

the next track. If you press the SKIP ( ) button, it moves

to the beginning of the track. One more press makes it

move to the beginning of the previous track.

- If a track exceeds 15 minutes when playing a VCD and

you press the button, it moves forward 5minutes.

If you press the button, it moves backward 5 minutes.

Note

When playing VCD2.0, this function works only when the menu is off. Select Menu Off by pressing the DISC MENU button.

Using the Display Function

When Playing a DVD/VCD/MPEG4

1. During play, press the INFO button on the remote control.

2. Press the /buttons to select the desired item.

- When playing VCD2.0, this function works only when the menu is off. Select Menu Off by pressing the DISC MENU button.

3. Press the ¦/ buttons to make the desired setup and then

press the ENTER button.

- You may use the number buttons of the remote control to directly access a title, chapter or to start the play back from a desired time.

4. To make the screen disappear, press the CANCEL button.

Note

To access the desired title when there is more than one in the disc. For example, if there is more than one movie on a DVD, each movie will be identified.

Most DVD discs are recorded in chapters so that you can quickly find a specific passage (similar to tracks on an video CD).

Allows playback of the film from a desired time. You must enter the starting time as a reference.The time search function does not operate on some disc.

Refers to the language of the film soundtrack. In the example, the soundtrack is played in English 5.1CH. A DVD disc can have up to eight different soundtracks.

Refers to the subtitle languages available in the disc. You will be able to choose the subtitle languages or, if you prefer, turn them off from the screen. A DVD disc can have up to 32 different subtitles.

To access the desired Bookmark or Angle function. Some DVD discs are have more angle function from any picture. Bookmark function make you easily and quickly to find a track or chapter from DVD or VCD ( Menu Off).

The EZ View funtion is use for changing the aspect ratio in DVD.

English

Using the Disc and Title Menu

Using the Disc Menu

1. During Stop mode, press the MENU button on the remote control.

2. Press the / buttons to select Disc Menu, then press the

 or ENTER button.

Press ENTER key for Disc Menu

Note

- Depending on a disc, the Disc Menu may not work.

- You can also use the Disc Menu, using the DISC MENU button on the remote control.

- When playing VCD2.0, this function works only when the menu is off. Select Menu Off by pressing the DISC MENU button.

Using the Title Menu

1. During Stop mode, press the MENU button on the remote control.

2. Press the / buttons to select Title Menu, then press the

 or ENTER button.

Press ENTER key for Title Menu

Repeat Play

Repeat the current track, chapter, title, a chosen section (A-B), or all of the disc.

When playing a DVD/VCD

1. Press the REPEAT button on the remote control. Repeat screen appears.

2. Press the ¦/ buttons to select Chapter, Title or A-B,

then press the ENTER button.

- DVD repeats play by chapter or title, VCD repeat play by disc or track.

- Chapter ( ): repeats the chapter that is playing.

- Title ( ): repeats the title that is playing.

- Disc ( ): repeats the disc that is playing.

- Track ( ): repeats the track that is playing.

- A-B: repeats a segment of the disc that you select.

DVD

REPEAT

Off 01 01 A - B

VCD

Off 01 01 A - B

Using the A-B Repeat function

1. Press the REPEAT A-B button at the point where you

want repeat play to start (A). B is automatically highlighted.

2. Press the REPEAT A-B button at the point where you

want the repeat play to stop (B).

- To return to normal play, press the CANCEL button.

3. To return to normal play, press REPEAT button again, then

press the ¦/ buttons to select Off and press ENTER button.

DVD

Off 01 01 A - B

ENTER

REPEAT

ENTER

REPEAT

ENTER

Note

- Depending on a disc, the Title Menu may not work.

VCD

Off 01 01 A - B

REPEAT

ENTER

- Title Menu will only be displayed if there are at least two titles in the disc.

Note

- A-B REPEAT allows you to set point (B) until at

least 5 seconds of play back time has elapsed after point (A) has been set

- Depending on a disc, the Repeat function may not work.

- When playing VCD2.0, this function works only when

the menu is off. Select Menu Off by pressing the DISC MENU button.

Slow Play

This feature allows you slowly to repeat scenes containing sports, dancing, musical instruments being played etc., so you can study them more closely.

When playing a DVD

1. During play, press the PLAY/PAUSE ( ) button.

2. Press the SEARCH (/) button to choose the play speed between 1/8, 1/4 and 1/2 of normal during PAUSE or

STEP mode.

ADV

FUNCTIONS

ANCED

Adjusting the Aspect Ratio (EZ View)

To play back using aspect ratio (DVD)

Press the EZ VIEW button.

- The screen size changes when the button is pressed repeatedly.

- The screen zoom mode operates differently depending on the screen setting in the Display Setup menu.

- To ensure correct operation of the EZ VIEW button, you

should set the correct aspect ratio in the Display Setup menu. (See pages 27-28).

WIDE SCREEN

If you are using a 16:9 TV

For 16:9 aspect ratio discs

- WIDE SCREEN Displays the content of the DVD title in 16:9 aspect ratio.

- SCREEN FIT

The top and bottom portions of the screen are cut off. When playing a 2.35:1 aspect ratio disc, the black bars at the top and bottom of the screen will disappear. The picture will look vertically stretched. (Depending on a type of disc, the black bars may not disappear completely.)

- ZOOM FIT

The top, bottom, left and right of the screen are cut off and the central portion of the screen is enlarge

For 4:3 aspect ratio discs

- Normal Wide

Displays the content of the DVD title in 16:9 aspect ratio. The picture will look horizontally stretched.

- SCREEN FIT

The top and bottom portions of the screen are cut off and the full screen appears. The picture will look vertically stretched.

- ZOOM FIT

The top, bottom, left and right portions of the screen are cut off and the central portion of the screen is enlarged.

- Vertical Fit

When a 4:3 DVD is viewed on a 16:9 TV, black bars will appear at the left and right of the screen in order to prevent the picture from looking horizontally stretched.

EZ VIEW

English

If you are using a 4:3 TV

For 16:9 aspect ratio discs

- 4:3 Letter Box

Displays the content of the DVD title in 16:9 aspect ratio. The black bars will appear at the top and bottom of the screen.

- 4:3 Pan Scan

The left and right portions of the screen are cut off and the central portion of the 16:9 screen is displayed.

- SCREEN FIT

The top and bottom portions of the screen are cut off and a full screen appears. The picture will look vertically stretched.

- ZOOM FIT

The top, bottom, left and right of the screen are cut off and the central portion of the screen is enlarged.

For 4:3 aspect ratio discs

- Normal Screen

Displays the content of the DVD title in 4:3 aspect ratio.

- SCREEN FIT

The top and bottom portions of the screen are cut off and the

full screen appears. The picture will look vertically stretched.

- ZOOM FIT

The top, bottom, left and right portions of the screen are cut off and the central portion of the screen is enlarged.

Note

This function may behave differently depending on the type of disc.

Selecting the Audio Language

You can select a desired audio language quickly and easily with the AUDIO button.

Using the AUDIO button (DVD/VCD/MPEG4)

1. Press the AUDIO button. The Audio changes when the button is pressed repeatedly. The audio languages are represented by abbreviations.

When playing a VCD you can select among Stereo, Right or Left.

Press Audio button at remocon repeatedly to select the desired Audio on MPEG4 then press the ENTER .

DVD

ENG

VCD

Stereo

MPEG4

PCM 1/2

DOLBY DIGITAL 5.1CH

AUDIO

2. To remove the AUDIO icon, press the CANCEL or RETURN button.

Note

- This function depends on audio languages are encoded on the disc and may not work.

- A DVD disc can contain up to 8 audio languages.

- To have the same audio language come up whenever you play a DVD; Refer to “Using the Audio Language” on page 26.

Selecting the Subtitle Language

You can select a desired subtitle quickly and easily with the SUBTITLE button.

Using the SUBTITLE button

(DVD/MPEG4)

1. Press the SUBTITLE button. The subtitle languages are represented by abbreviations. The subtitle changes when the button is pressed repeatedly.

External Subtitle option will appear, depends on the DivX disc.

Press SUBTITLE button at remocon repeatedly to select the desired subtitle language on a MPEG4 then press the ENTER .

2. To remove the SUBTITLE icon, press the CANCEL or

RETURN button.

Note

- You have to change the desired subtitle in the Disc Menu, according to discs. Press the DISC MENU button.

- This function depends on what subtitles are encoded on the disc and may not work on all DVDs.

- A DVD disc can contain up to 32 subtitle languages.

- To have the same subtitle language come up whenever you play a DVD; Refer to “Using the Subtitle Language” on page 26.

DVD

SUBTITLE

Off

MPEG4

Subtitle Selection

External Subtitle Off

readme.TXT

Non-standard fonts are not supported

MPEG4

Off

ReturnEnter

SUBTITLE

Changing the Camera Angle

When a DVD contains multiple angles of a particular scene, you can use the ANGLE function.

Using the ANGLE button (DVD)

If the disc contains multiple angles, the ANGLE appears on the screen.

¦/

3. Press the

buttons to select Bookmark (except VCD),

then press the ENTER button.

4. When you reach the scene you want to mark, press the ENTER button. Up to three scenes may be marked at a time.

1 - -

1. During play, press the INFO button on the remote control.

2. Press the / buttons to select Shortcut.

¦/

3. Press the

buttons to select Angle, then press the

ENTER button.

Enter

4. Press the

Angle

Shortcut

¦/

buttons on the remote control to select the

desired angle.

4/6

Note

- If the disc has only one angle, this feature won’t work. Currently, very few discs have this feature.

- Depending on the disc, these functions may not work.

Using the Bookmark Function

This feature lets you bookmark sections of a DVD or VCD (Menu Off mode) so you can quickly find them at a later time.

Using the Bookmark Function (DVD/VCD)

1. During play, press the INFO button on the remote control.

2. Press the / buttons to select Shortcut.

DVD

Note

- When VCD 2.0 is in Menu Off mode only, this function works. Select Menu Off by pressing the DISC MENU button.

- Depending on a disc, the Bookmark function

may not work.

Recalling a Marked Scene

1~3. The first 1~3 steps are the same as those for “Using the

Bookmark Function” on page 19.

¦/

4. Press the

buttons to select a marked scene.

1 2 3

5. Press the PLAY/PAUSE ( ) button to skip to the marked scene.

Clearing a Bookmark

1~3. The first 1~3 steps are the same as those for “Using the

Bookmark Function” on page 19.

¦/

4. Press the want to delete.

5. Press the CANCEL button to delete a bookmark number.

buttons to select the bookmark number you

1 2 3

English

VCD

Shortcut

Bookmark

Enter

Using the Zoom Function

Using the Zoom Function (DVD/VCD)

1. During play or pause mode, press the ZOOM button on the remote control, press the ENTER button.

2. Press the

// ¦/

screen you want to zoom in on.

- During DVD play, press ENTER to zoom in 2X/4X/2X/Normal in order.

- During VCD play, press ENTER to zoom in 2X/4X/2X/Normal in order.

buttons to select the part of the

- : Name of currently playing file.

- : Current Playback Time.

- : Current Playback Mode : There are four

modes. They can be selected in order by

pressing the REPEAT button.

- Off: Normal Playback

- Track: Repeats the current track.

- Folder: Repeats the current folder

- Random: Files in the disc will be played in

random order.

- : MP3 file icon. - : CD Audio file icon.

- : WMA file icon. - : Folder icon.

- : JPEG file icon - : Current Folder icon.

- : AVI file icon.

Folder Selection

The folder can be selected in Stop or Play mode.

- To select the Parent Folder

Press the RETURN button to go to parent folder, or press the

/

buttons to select “..” and press ENTER to go to the

parent folder.

Clips Menu for MP3/WMA/ JPEG/ MPEG4/CD Audio

CD Audio or discs with MP3/WMA/JPEG contain individual songs and/or pictures that can be organized into folders as shown below. They are similar to how you use your computer to put files into different folders.

Open the disc tray. Place the disc on the tray. Close the tray. The tray closes and this screen displays.

Off

- To select the Peer Folder

/

Press the

buttons to select the desired folder, then

press ENTER.

- To select the Sub-Folder

/

Press the

buttons to select the desired folder,

then press ENTER.

Root

WMA

JPEG

MUSIC

1st

2nd

SONG FILE 1

SONG FILE 2

Parent Folder

Current Folder

MP3

SONG FILE 3

MPEG4 FILES

Sub-Folders

Peer Folders

MP3/WMA/CD Audio Playback

1. Open the disc tray. Place the disc on the tray. Close the tray.

- Only one kind of file is played back when a disc or a folder contains both MP3 and WMA files.

2. Press the /or ¦¦/buttons to select a song file. Press ENTER to begin playback of the song file.

Play

Because You

...

Because You

Cactus

Sad Dayu

Wonderful

Repeat/Random playback

Press the REPEAT button to change the playback mode. There are four modes, such as Off, Track, Folder and Random.

- Off: Normal Playback

- Track: Repeats the current song file.

- Folder: Repeats the song files which have the same extension in the current folder.

- Random: Song files which have the same extension will be played in random order.

To resume normal play, press the CANCEL button.

CD-R MP3/WMA file

When you record MP3 or WMA files on CD-R, please refer to the following.

- Your MP3 or WMA files should be ISO 9660 or JOLIET format.

ISO 9660 format and Joliet MP3 or WMA files are compatible with Microsoft's DOS and Windows, and with

Apple's Mac. This format is the most widely used.

- When naming your MP3 or WMA files, do not exceed 8 characters, and enter “.mp3, .wma” as the file extension.

General name format : Title.mp3. or Title.wma. When composing your title, make sure that you use 8 characters or less, have no spaces in the name, and avoid the use of special characters including: (.,/,\,=,+).

- Use a decompression transfer rate of at least 128 Kbps when recording MP3 files.

Sound quality with MP3 files basically depends on the rate of compression/decompression you choose. Getting CD audio sound requires an analog/digital sampling rate, that is conversion to MP3 format, of at least 128 Kbps and up to 160 Kbps. However, choosing higher rates, like 192 Kbps or more, only rarely give better sound quality. Conversely, files with decompression rates below 128 Kbps will not be played properly.

Off

00:00:23

REPEAT

ReturnEnter

Repeat

- Use a decompression transfer rate of at least 64Kbps when recording WMA files.

Sound quality with WMA files basically depends on the rate of compression/decompression you choose. Getting CD audio sound requires an analog/digital sampling rate, that is conversion to WMA format, of at least 64Kbps and up to 192Kbps. Conversely, files with decompression rates below 64Kbps or over 192Kbps will not be played properly.

- Do not try recording copyright protected MP3 files.

Certain "secured" files are encrypted and code protected to prevent illegal copying. These files are of the following types: Windows Media SDMI

(registered trade mark of Microsoft Inc) and

(registered trade mark of The SDMI Foundation). You

cannot copy such files.

- Important:

The above recommendations cannot be taken as a guarantee that the DVD player will play MP3 recordings, or as an assurance of sound quality. You should note that certain technologies and methods for MP3 file recording on CD-Rs prevent optimal playback of these files on your DVD player (degraded sound quality and in some cases, inability of the player to read the files).

- This unit can play a maximum of 500 files and 500 folders per disc.

MPEG4 Playback

MPEG4 Play Function

AVI files are used to contain the audio and video data. Only

AVI format files with the “.avi” extensions can be played.

1. Open the disc tray. Place the disc on the tray.

Close the tray.

2. Press the

Repeat playback

Press the REPEAT button to change playback mode. There are 4 modes, such as Off, Folder, Title an A-B (a distance between two points appointed by user)

- Folder : repeats the AVI files which have the same extension

- Title : repeats the title that is playing.

- A-B : repeats a segment of the file that you select.

/

or ¦¦/buttons to select an avi file

(DivX/XviD) and then press ENTER button.

/MPEG4

...

a01_divx51b-8

a02_divx505b-8

a03_divx502sp-8

a04_divx412-8

Enter Return

in the current folder.

OffStop

00:00:00

English

MPEG4 Function Description

Function Description Reference page

During play, press the or

Skip

( or )

Slow Motion

Play

Step Motion

Play

ZOOM

button, it moves forward

or backward 5 minutes. During play, press the SEARCH

( or ) button and press again to search at a faster

Allows you to search

speed. at a faster speed in an AVI file. (2X, 4X, 8X)

Allows you to search at a slower speed in an AVI file. (1/8X, 1/4X, 1/2X)

Each time the STEP button is pressed, a new frame will appear.

2X/4X/2X/Normal in order

P15

P20

- These functions may not work depending on MPEG4 file.

Playing Media Files Using the USB Host feature

You can enjoy the media files such as pictures, movies and

tunes saved in an MP3 player, USB memory or digital cam-

era in high audio by connecting the storage device to the

USB port of the DVD Player.

Using the USB HOST feature

1. Connect the USB device to the USB port on the front of the unit.

2. If there is partision Of USB, Press the the one of partision from USB, then Press OK.

/

button to select

CD-R AVI file

This unit can play the following video compression formats within the AVI file format:

- DivX 3.11 contents

- DivX 4 contents (Based on MPEG-4 Simple Profile)

- DivX 5 contents (MPEG-4 simple profile plus additional features such as bi-directional frames. Qpel and GMC are also supported.)

- XviD MPEG-4 compliant Contents.

This unit supports all resolutions up to maximum below.

DivX3.11 & DivX4 & XviD DivX5

Bitrate may fluctuate: Device may skip decoding the high bitrate portions

720 x 480 @30fps 720 x 576 @25fps

: Maximum bitrate : 4Mbps and begin decoding again when Bitrate returns to normal.

Note

• Some MPEG-4 files created on a personal computer may not be play back. That is why Codec Type, Version and Higher resolution over specification is not supported.

• This unit supports CD-R/RW written in MPEG4 in accordance with the “ISO9660 format”.

3. Press the /or ¦¦/buttons to select a file in USB. Press OK to Open file.

STOP

Off

00:00:00

Note

• Each time the USB button on the remote control is pressed, a frame of the USB device selection will appear. “USB” appears on the display screen.

• USB MENU screen appears on the TV screen and the

• saved file is played.

Safe USB Removal

To prevent damage to the memory stored in the USB device, perform safe removal before disconnecting the USB cable.

- Press the STOP ( ) button

- Remove the USB cable.

Skip Forward/Back

During playback, press the

When there is more than one file, when you press the

• button, the next file is selected. When there is more than one file, when you press the

• button, the previous file is selected

(/)

button.

Fast playback

CANCEL

To play back the disc at a faster speed, press

(/)d

Each time you press either button, the playback speed will

• change as follows: 2x ➞ 4x ➞ 8x.

uring playback.

Compatible Devices

1. USB devices that support USB Mass Storage v1.0. (USB devices that operate as a removable disk in Windows (2000 or later) without additional driver installation.)

2. MP3 Player: Flash type MP3 player.

3. Digital camera: Cameras that support USB Mass Storage v1.0.

• Cameras that operate as a removable disk in Windows (2000 or later) without additional driver installation.

4. USB Flash Drive: Devices that support USB2.0 or USB1.1.

• You may experience a difference in playback quality when you connect a USB1.1 device.

5. USB card Reader: One slot USB card reader and Multi slot USB card reader

• Depending on the manufacturer. the USB card reader may not be supported.

• If you install multiple memory devices into a multi card

reader, you may experience problems.

6. If you use a USB extension cable, the USB device might not be recognized.

• Supported Formats

The USB HOST function is not supported if a product that

• transfers media files by its manufacturer-specific program is connected. Does not operate with Janus enabled MTP(Media Transfer

• Protocol) devices.

The USB host function of this product does not support

•

all USB devices. For information on the supported devices, see page 32.

CD Ripping

This feature lets you to copy audio files from disc to USB

device into MP3 format.

Open the dics tray.

Place the Audio CD(CD DA) disc on the tray, and close the tray.

Connect the USB device to the USB port on the front of the unit.

This screen will displayed.

1. To Select DISC With the unit in Stop mode, Press the

select DISC.

To Select DEV (storage media device)

Press the



Press the device) menu, then press the ENTER button.

button to select the DEV (storage media

/

buttons to select USB, then press the

ENTER button.

Play

Track 01

Track 02

Track 03

Track 04 Track 05

Track 06

Track 07

Track 08

Enter

/

Stop

Off

00:00:05

DEV : SELECT START

REPEAT

Repeat

buttons to

Off

English

CBI (Control/Bulk/Interrupt) is not supported.

• Digital Cameras that use PTP protocol or require additional

• program installation when connected to a PC are not supported.

A device using NTFS file system is not supported.

•

(Only FAT 16/32 (File Allocation Table 16/32) file system is supported.) Some MP3 players, when connected to this product,may not

•

operate depending on the sector size of their file system.

/

2. Press the ENTER button to marked all files to be copying.

buttons to select SELECT, then press the

- To unmarked copying all files press the ENTER button again.(UNSELECT Menu)

- If you want to marked several files to be copying, press the

¦¦

button, then press the ENTER button on the selected

file.

/

3. Press the ENTER button.

buttons to select START, then press the

File copy begins.

- To cancel the copying in progress, press the CANCEL but ton.

Play

Track 01

Track 02

Track 03

Track 04 Track 05

CD Ripping START

Track 06

Track 07

Cancel Ripping

Enter

Off

00:03:15

DEV : USB 1 UNSELECT START

REPEAT

Repeat

+ 51 hidden pages