Samsung DVD-H40E Service Manual
DVD HDD RECORDER
DVD-H40E
SERVICE
1. Precautions
2. Exploded Views and Parts List
3. Electrical Parts List
4. Block Diagram
5. Schematic Diagrams
Manual
DVD HDD RECORDER CONTENTS
SERVICE MANUAL DVD-H40E
ELECTRONICS
© Samsung Electronics Co., Ltd. OCT. 2002
Printed in Korea
AK82-00261A
Samsung Electronics 1-1
1. Precautions
1-1 Safety Precautions
1) Before returning an instrument to the customer,
always make a safety check of the entire instrument,
including, but not limited to, the following items:
(1) Be sure that no built-in protective devices are
defective or have been defeated during servicing.
(1)Protective shields are provided to protect both
the technician and the customer. Correctly replace
all missing protective shields, including any
remove for servicing convenience.
(2)When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place
all protective devices, including, but not limited to,
nonmetallic control knobs, insulating fish papers,
adjustment and compartment covers/shields, and
isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and
functioning.
(2) Be sure that there are no cabinet openings through
which adults or children might be able to insert
their fingers and contact a hazardous voltage. Such
openings include, but are not limited to, excessively wide cabinet ventilation slots, and an improperly fitted and/or incorrectly secured cabinet back
cover.
(3) Leakage Current Hot Check-With the instrument
completely reassembled, plug the AC line cord
directly into a 120V AC outlet. (Do not use a isolation transformer during this test.) Use a leakage
current tester or a metering system that complies
with American National Standards institute (ANSI)
C101.1 Leakage Current for Appliances and
Underwriters Laboratories (UL) 1270 (40.7). With
the instrument’s AC switch first in the ON position
and then in the OFF position, measure from a
known earth ground (metal water pipe, conduit,
etc.) to all exposed metal parts of the instrument
(antennas, handle brackets, metal cabinets, screwheads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis.
Any current measured must not exceed 0.5mA.
Reverse the instrument power cord plug in the outlet and repeat the test. See Fig. 1-1.
Any measurements not within the limits specified
herein indicate a potential shock hazard that must
be eliminated before returning the instrument to
the customer.
Fig. 1-1 AC Leakage Test
(4) Insulation Resistance Test Cold Check-(1) Unplug
the power supply cord and connect a jumper wire
between the two prongs of the plug. (2) Turn on the
power switch of the instrument. (3) Measure the
resistance with an ohmmeter between the
jumpered AC plug and all exposed metallic cabinet
parts on the instrument, such as screwheads,
antenna, control shafts, handle brackets, etc. When
an exposed metallic part has a return path to the
chassis, the reading should be between 1 and 5.2
megohm. When there is no return path to the chassis, the reading must be infinite. If the reading is
not within the limits specified, there is the possibility of a shock hazard, and the instrument must be
re-pared and rechecked before it is returned to the
customer. See Fig. 1-2.
Fig. 1-2 Insulation Resistance Test
DEVICE
UNDER
TEST
(READING SHOULD
NOT BE ABOVE
0.5mA)
LEAKAGE
CURRENT
TESTER
EARTH
GROUND
TEST ALL
EXPOSED METER
SURFACES
ALSO TEST WITH
PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED)
2-WIRE CORD
Antenna
Terminal
Exposed
Melal Part
ohm
ohmmeter
Precautions
1-2 Samsung Electronics
2) Read and comply with all caution and safety related notes non or inside the cabinet, or on the chassis.
3) Design Alteration Warning-Do not alter of add to
the mechanical or electrical design of this instrument. Design alterations and additions, including
but not limited to, circuit modifications and the
addition of items such as auxiliary audio output
connections, might alter the safety characteristics of
this instrument and create a hazard to the user. Any
design alterations or additions will make you, the
service, responsible for personal injury or property
damage resulting therefrom.
4) Observe original lead dress. Take extra care to
assure correct lead dress in the following areas:
(1) near sharp edges, (2) near thermally hot parts (be
sure that leads and components do not touch thermally hot parts), (3) the AC supply, (4) high voltage,
and (5) antenna wiring. Always inspect in all areas
for pinched, out-of-place, or frayed wiring, Do not
change spacing between a component and the
printed-circuit board. Check the AC power cord for
damage.
5) Components, parts, and/or wiring that appear to
have overheated or that are otherwise damaged
should be replaced with components, parts and/ or
wiring that meet original specifications.
Additionally, determine the cause of overheating
and/or damage and, if necessary, take corrective
action to remove any potential safety hazard.
6) Product Safety Notice-Some electrical and mechanical parts have special safety-related characteristics
which are often not evident from visual inspection,
nor can the protection they give necessarily be
obtained by replacing them with components rated
for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by shading,
an ( )or a ( )on schematics and parts lists. Use
of a substitute replacement that does not have the
same safety characteristics as the recommended
replacement part might created shock, fire and/or
other hazards. Product safety is under review continuously and new instructions are issued whenever appropriate.
Precautions
Samsung Electronics 1-3
1-2 Servicing Precautions
CAUTION : Before servicing Instruments covered
by this service manual and its supplements, read and
follow the Safety Precautions section of this manual.
Note : If unforseen circument create conflict between
the following servicing precautions and any of the
safety precautions, always follow the safety precautions. Remember: Safety First.
1-2-1 General Servicing Precautions
(1) a. Always unplug the instrument’s AC power cord
from the AC power source before (1) re-moving
or reinstalling any component, circuit board,
module or any other instrument assembly, (2)
disconnecting any instrument electrical plug or
other electrical connection, (3) connecting a test
substitute in parallel with an electrolytic capacitor in the instrument.
b. Do not defeat any plug/socket B+ voltage inter-
locks with which instruments covered by this
service manual might be equipped.
c. Do not apply AC power to this instrument and
/or any of its electrical assemblies unless all
solid-state device heat sinks are correctly installed.
d. Always connect a test instrument’s ground lead
to the instrument chassis ground before connecting the test instrument positive lead. Always
remove the test instrument ground lead last.
Note : Refer to the Safety Precautions section ground
lead last.
(2) The service precautions are indicated or printed on
the cabinet, chassis or components. When servicing, follow the printed or indicated service precautions and service materials.
(3) The components used in the unit have a specified
flame resistance and dielectric strength.
When replacing components, use components
which have the same ratings. Components i-entified by shading, by( ) or by ( ) in the circuit diagram are important for safety or for the characteristics of the unit. Always replace them with the exact
replacement components.
(4) An insulation tube or tape is sometimes used and
some components are raised above the printed
wiring board for safety. The internal wiring is
sometimes clamped to prevent contact with heating components. Install such elements as they
were.
(5) After servicing, always check that the removed
screws, components, and wiring have been installed correctly and that the portion around the
serviced part has not been damaged and so on.
Further, check the insulation between the blades of
the attachment plug and accessible conductive
parts.
1-2-2 Insulation Checking Procedure
Disconnect the attachment plug from the AC outlet
and turn the power ON. Connect the insulation resistance meter (500V) to the blades of the attachment
plug. The insulation resistance between each blade of
the attachment plug and accessible conductive
parts(see note) should be more than 1 Megohm.
Note : Accessible conductive parts include metal panels, input terminals, earphone jacks, etc.
Precautions
1-4 Samsung Electronics
1-3 ESD Precautions
Electrostatically Sensitive Devices (ESD)
Some semiconductor (solid state) devices can be damaged easily by static electricity.
Such components commonly are called Electrostatically Sensitive Devices(ESD). Examples of typical ESD
devices are integrated circuits and some field-effect
transistors and semiconductor chip components. The
following techniques should be used to help reduce
the incidence of component damage caused by static
electricity.
(1) Immediately before handling any semiconductor
component or semiconductor-equipped assembly,
drain off any electrostatic charge on your body by
touching a known earth ground. Alternatively,
obtain and wear a commercially available discharging wrist strap device, which should be
removed for potential shock reasons prior to applying power to the unit under test.
(2) After removing an electrical assembly equipped
with ESD devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
(3) Use only a grounded-tip soldering iron to solder or
unsolder ESD devices.
(4) Use only an anti-static solder removal devices.
Some solder removal devices not classified as
“anti-static” can generate electrical charges sufficient to damage ESD devices.
(5) Do not use freon-propelled chemicals. These can
generate electrical charges sufficient to damage
ESD devices.
(6) Do not remove a replacement ESD device from its
protective package until immediately before your
are ready to install it.(Most replacement ESD
devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or
comparable conductive materials).
(7) Immediately before removing the protective ma-
terials from the leads of a replacement ESD device,
touch the protective material to the chassis or circuit assembly into which the device will be
installed.
CAUTION : Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
(8) Minimize bodily motions when handling unpack-
aged replacement ESD devices. (Otherwise harmless motion such as the brushing together of your
clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient
to damage an ESD device).
Precautions
Samsung Electronics 1-5
1-4 Handling the optical pick-up
The laser diode in the optical pick up may suffer electrostatic breakdown because of potential static electricity from clothing and your body.
The following method is recommended.
(1) Place a conductive sheet on the work bench (The
black sheet used for wrapping repair parts.)
(2) Place the set on the conductive sheet so that the
chassis is grounded to the sheet.
(3) Place your hands on the conductive sheet(This
gives them the same ground as the sheet.)
(4) Remove the optical pick up block
(5) Perform work on top of the conductive sheet. Be
careful not to let your clothes or any other static
sources to touch the unit.
◆ Be sure to put on a wrist strap grounded to the
sheet.
◆ Be sure to lay a conductive sheet made of copper
etc. Which is grounded to the table.
Fig.1-3
(6) Short the short terminal on the PCB, which is in-
side the Pick-Up ASS’Y, before replacing the PickUp. (The short terminal is shorted when the PickUp Ass’y is being lifted or moved.)
(7) After replacing the Pick-up, open the short termi-
nal on the PCB.
THE UNIT
WRIST-STRAP
FOR GROUNDING
1M
1M
CONDUCTIVE SHEET
Precautions
1-6 Samsung Electronics
1-5 Pick-up disassembly and reassembly
1-5-1 Disassembly
1) Remove the power cord.
2) Disassemble the Deck-Assy.
3) Make solder land 2 points short on Pick-up.
(See Fig. 1-4)
4) Disassembly the Pick-up.
1-5-2 Assembly
1) Replace the Pick-up.
2) Remove the soldering 2 points on Pick-up.
3) Reassemble the Deck-Assy.
SOLDER LAND 2 POINTS SHORT
PICK-UP ASS'Y
Note : If the assembly and disassembly are not done in correct sequence, the Pick-up may be damaged.
Fig. 1-4
2-1
2. Exploded View and Parts List
2-1 Cabinet Assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
2-2 Deck Assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Page
2-2
2-4
You can search for the updated part code through ITSELF web site.
URL; http://itself.sec.samsung.co.kr
Notice
Exploded Views and Parts List
2-2
2-1 Cabinet Assembly
S.N.A. : Service Not Available
UT01
1
2
3
FWD
101
151
ASSY-DVD DECK (S.N.A.)
701 (FUNCTION-TIMER)
702 (POWER-KEY PCB)
610
601 (ASS'Y-PCB-MAIN)
602 (ASS'Y-PCB-SMPS)
155
155
155
155
151
151
12
155
155
14
15
HDD
12
157
153
153
151
151
Exploded Views and Parts List
2-3
Loc. No Parts No. Description ; Specification Remark
1 AK97-00163A ASSY-PANEL FRONT;HIPS94HB,HDD COMBO,SILV
2 AK64-00026A DOOR-TRAY;HDD COMBO,ABS 94HB,-,-,-,-,-,3 AC61-00267A SPRING ETC-DOOR TRAY;DVD-V5000K,SUS304,12 AC61-00204A LEG;RCA,ABS,-,SILVER(31HG),-,14 3103-001117 FAN-DC;12V,90MA,3000RPM,0.24M^3/MI,2M
15 AK69-00042A CUSHION-RUBBER FAN;DVD-H40U,FAN,5,-,-,-,
101 AK64-00024A CABINET-TOP;HDD COMBO,PCM(SECC),T0.6,-,151 6003-000276 SCREW-TAPTITE;BH,+,B,M3,L10,ZPC(YEL),SWC
153 6001-000742 SCREW-MACHINE;PH,+,UNC6-32,L4.2,ZPC(WHT)
155 6003-000275 SCREW-TAPTITE;BH,+,B,M3,L10,BLK ,SWCH101
157 6003-001349 SCREW-TAPTITE;TH,+,B,M5,L10,NI PLT,SWRCH
601 AK92-00059A ASSY PCB-MAIN;DVD-H40E/XEF,MAIN PCB ASS’
602 AK92-00055A ASSY PCB-SMPS;DVD-H40,SMPS PCB ASS’Y
610 3903-000059 CBF-POWER CORD;CP2,250V,2.5A,1730MM,H03V
701 AK92-00053A ASSY PCB-F/TIMER;DVD-H40,F/TIMER PCB ASS
702 AK92-00093A ASSY PCB-POWER KEY;DVD-H40,POWER KEY PCB
HDD AH59-01063A HDD;40G,SV4002H,63,16,16383,25.4MM
UT01 AK59-00001G REMOCON-ASSY;DVD-H40E,-,-,-,47,-,-,-,-,M
Exploded Views and Parts List
2-4
2-2 Deck Assembly
H108
H106
S.N.A.
H105
H107
H102
H211
H203
H241
H212
905
H104
H250
H103
H207
H208
S.N.A.
H202
H210
H204
H205
H209
H206
901
900
904
906
903
Exploded Views and Parts List
2-5
Loc. No Parts No. Description ; Specification Remark
900 6003-001157 SCREW-TAPTITE;PWH,+,B,M2,L6,ZPC(YEL),SWR
901 6001-001522 SCREW-MACHINE;FH,+,M2.6,L7,ZPC(YEL),SWRC
903 6009-001245 SCREW-SPECIAL;SWRCH18A,NYLOCK,SOCKET,HEX
904 6001-001466 SCREW-MACHINE;BH,+,M2,L6,ZPC(BLK),SWRCH1
905 6001-001257 SCREW-MACHINE;PWH,+,M1.7,L3,ZPC(YEL),SWR
906 AH60-00010A SCREW-MACHINE-MOTOR;-,+,SWCH18AK,M1.7,L2
H102 AH66-00111B CLAMPER-ASSY;DP-5,POM+MAGNET,-,-,-,-,-,H103 AH66-00123A PULLEY-GEAR;DP-7,POM M90-44,-,-,-,-,-,H104 AH31-00024A MOTOR-LOAD ASSY;SM-2412L2,DP-7,-,-,-,-,H105 6602-001076 BELT-RECTANGULAR;CR,T1.2,4.3%,1.2X25.1,B
H106 AH66-00124A GEAR-TRAY;DP-7,POM,M90-44,-,-,-,-,-,-,H107 AH66-00125A SLIDER-HOUSING;DP-7,POM,-,-,-,-,H108 AH63-00422A TRAY-DISC;-,ABS,-,-,-,-,BLK,DP-7S
H202 AH73-00023A RUBBER-INSULATOR;BUTYL RUBBER,-,DP-3
H203 AH61-50327A SHAFT-P/U;DP-3,SUS420J2,L84.7,OD3,-,-,H204 AH66-00075A GEAR-FEED A;-,POM M90-44,-,-,-,-,-,-,-,H205 AH66-00170A GEAR-FEED B;DP-7S,POM M90-44,0.5,14,-,-,
H206 AC60-30306A WASHER-SLIT;-,-,ID2.1,OD5.0,T0.5,-,POLYS
H207 AH31-00032A MOTOR-SPINDLE ASSY;RSM-2610F1,DP-7S,-,-,
H208 AH61-00403A SPRING ETC-SPINDLE;DP-5,SWPB,PI4.9,-,-,H209 AH61-00513A CHASSIS-SUB;DP-7,ABS(SR-0320),-,-,-,-,-,
H210 AH31-00016A MOTOR-FEED ASSY;-,DP-5,-,H211 AH97-00900Y ASSY-PICK UP;-,SOH-DS2,HD COMBO
H212 AH61-00891A HOLDER-FFC;DP-7S,PP,1,-,-,NTR,H241 3809-001303 CABLE-FLAT;30V,80C,230MM,24P,1MM,UL2896
H250 AH92-00900A ASSY-HOUSING PCB;DVD-M101,MILLENO DECK(B
Exploded Views and Parts List
2-6
MEMO
Loc.No Part No Description ; Specification Remark Loc.No Part No Description ; Specification Remark
Samsung Electronics
3-1
601 AK92-00059A ASSY PCB-MAIN;DVD-H40E/XEF,MAIN PCB ASS’
BC1 2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,BC10 2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,BC11 2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,BC12 2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,BC13 2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,BC14 2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,BC15 2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,BC16 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
BC17 2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,BC18 2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,BC19 2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,BC20 2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,BC22 2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,BC23 2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,BC24 2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,BC25 2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,BC26 2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,BC27 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
BC28 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
BC29 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
BC30 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
BC31 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
BC32 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
BC33 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
BC34 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
BC35 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
BC36 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
BC37 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
BC38 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
BC39 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
BC40 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
BC41 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
BC42 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
BC43 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
BC6 2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,BC7 2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,BC8 2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,BC9 2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,BL3 3301-000314 CORE-FERRITE BEAD;AB,120ohm,1.6x0.8x0.8m
BL4 3301-000314 CORE-FERRITE BEAD;AB,120ohm,1.6x0.8x0.8m
C101 2203-002398 C-CERAMIC,CHIP;22nF,10%,50V,X7R,TP,1608
C1012 2203-000783 C-CERAMIC,CHIP;0.33nF,5%,50V,NP0,TP,1608
C1013 2203-000783 C-CERAMIC,CHIP;0.33nF,5%,50V,NP0,TP,1608
C1014 2203-000783 C-CERAMIC,CHIP;0.33nF,5%,50V,NP0,TP,1608
C1015 2203-000783 C-CERAMIC,CHIP;0.33nF,5%,50V,NP0,TP,1608
C1022 2401-002042 C-AL;220uF,20%,10V,GP,TP,6.3x11,5
C1023 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1024 2401-001353 C-AL;470uF,20%,10V,GP,TP,8x11.5,5
C1025 2401-000913 C-AL;22uF,20%,16V,GP,TP,5x11,5
C1026 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C104 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
C105 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C106 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
C107 2401-000414 C-AL;10uF,20%,16V,GP,TP,4x7,5
C108 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
C110 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
C1101 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1102 2203-001656 C-CERAMIC,CHIP;0.47nF,5%,50V,NP0,TP,1608
C1103 2401-002042 C-AL;220uF,20%,10V,GP,TP,6.3x11,5
C1104 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1105 2401-000414 C-AL;10uF,20%,16V,GP,TP,4x7,5
C1106 2203-000715 C-CERAMIC,CHIP;3.3nF,10%,50V,X7R,TP,1608
C1107 2203-001656 C-CERAMIC,CHIP;0.47nF,5%,50V,NP0,TP,1608
C1108 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1109 2203-002398 C-CERAMIC,CHIP;22nF,10%,50V,X7R,TP,1608
C111 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1110 2203-001656 C-CERAMIC,CHIP;0.47nF,5%,50V,NP0,TP,1608
C1112 2401-000414 C-AL;10uF,20%,16V,GP,TP,4x7,5
C1113 2203-000715 C-CERAMIC,CHIP;3.3nF,10%,50V,X7R,TP,1608
C1114 2203-001656 C-CERAMIC,CHIP;0.47nF,5%,50V,NP0,TP,1608
C1116 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
C1117 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1118 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C112 2401-001085 C-AL;330nF,20%,50V,GP,-,5x9,2mm
C114 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
C115 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1202 2401-000255 C-AL;100uF,20%,10V,WT,TP,5x11,2mm
C1203 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608
C1204 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1205 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1206 2401-003059 C-AL;1000UF,20%,16V,WT,TP,10X16,5
C1207 2203-000626 C-CERAMIC,CHIP;0.022nF,5%,50V,NP0,TP,160
C1208 2203-000626 C-CERAMIC,CHIP;0.022nF,5%,50V,NP0,TP,160
C1209 2203-000626 C-CERAMIC,CHIP;0.022nF,5%,50V,NP0,TP,160
C1210 2203-000626 C-CERAMIC,CHIP;0.022nF,5%,50V,NP0,TP,160
C1401 2401-000255 C-AL;100uF,20%,10V,WT,TP,5x11,2mm
C1405 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
C1406 2401-000414 C-AL;10uF,20%,16V,GP,TP,4x7,5
C1407 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1408 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1411 2401-000255 C-AL;100uF,20%,10V,WT,TP,5x11,2mm
C1414 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1415 2401-000255 C-AL;100uF,20%,10V,WT,TP,5x11,2mm
C1416 2401-000414 C-AL;10uF,20%,16V,GP,TP,4x7,5
C1417 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
C1418 2401-000414 C-AL;10uF,20%,16V,GP,TP,4x7,5
C1419 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1420 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1421 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1422 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1423 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1424 2401-000414 C-AL;10uF,20%,16V,GP,TP,4x7,5
C1425 2401-000414 C-AL;10uF,20%,16V,GP,TP,4x7,5
C1427 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1428 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1429 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1430 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1431 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1432 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1433 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1434 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1435 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1436 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1439 2401-000414 C-AL;10uF,20%,16V,GP,TP,4x7,5
C1440 2401-000414 C-AL;10uF,20%,16V,GP,TP,4x7,5
C1441 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1442 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1443 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1444 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1445 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1446 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
3. Electrical Parts List
Loc.No Part No Description ; Specification RemarkLoc.No Part No Description ; Specification Remark
3-2
Samsung Electronics
Electrical Parts List
C1447 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1448 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1449 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1450 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1451 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1452 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1453 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1454 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1455 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1456 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1457 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1458 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1459 2401-000255 C-AL;100uF,20%,10V,WT,TP,5x11,2mm
C1460 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1461 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1462 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1463 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1464 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1465 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1466 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1467 2401-000255 C-AL;100uF,20%,10V,WT,TP,5x11,2mm
C1468 2401-000255 C-AL;100uF,20%,10V,WT,TP,5x11,2mm
C1469 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1470 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1471 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1472 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1473 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1474 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
C1475 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1476 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1477 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1478 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1479 2401-000414 C-AL;10uF,20%,16V,GP,TP,4x7,5
C1480 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1481 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1482 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1483 2401-000414 C-AL;10uF,20%,16V,GP,TP,4x7,5
C1484 2401-000255 C-AL;100uF,20%,10V,WT,TP,5x11,2mm
C1488 2401-000414 C-AL;10uF,20%,16V,GP,TP,4x7,5
C1489 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1490 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1491 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1492 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1493 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1494 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1495 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1496 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1497 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1498 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1499 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1500 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1501 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1502 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1503 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1504 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1505 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1506 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1507 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1508 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1509 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1510 2401-000255 C-AL;100uF,20%,10V,WT,TP,5x11,2mm
C1511 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1512 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1513 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1514 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1515 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1516 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1517 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1518 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1519 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1520 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1521 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1522 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1801 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1802 2203-000783 C-CERAMIC,CHIP;0.33nF,5%,50V,NP0,TP,1608
C1803 2203-000783 C-CERAMIC,CHIP;0.33nF,5%,50V,NP0,TP,1608
C1804 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1805 2401-000255 C-AL;100uF,20%,10V,WT,TP,5x11,2mm
C1806 2401-000913 C-AL;22uF,20%,16V,GP,TP,5x11,5
C1807 2401-000255 C-AL;100uF,20%,10V,WT,TP,5x11,2mm
C1808 2401-000913 C-AL;22uF,20%,16V,GP,TP,5x11,5
C1809 2401-000255 C-AL;100uF,20%,10V,WT,TP,5x11,2mm
C1810 2401-000913 C-AL;22uF,20%,16V,GP,TP,5x11,5
C1811 2203-000783 C-CERAMIC,CHIP;0.33nF,5%,50V,NP0,TP,1608
C1812 2203-000783 C-CERAMIC,CHIP;0.33nF,5%,50V,NP0,TP,1608
C1813 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1814 2203-000236 C-CERAMIC,CHIP;0.1nF,5%,50V,NP0,TP,1608
C1815 2203-000783 C-CERAMIC,CHIP;0.33nF,5%,50V,NP0,TP,1608
C1816 2203-000783 C-CERAMIC,CHIP;0.33nF,5%,50V,NP0,TP,1608
C1817 2203-000783 C-CERAMIC,CHIP;0.33nF,5%,50V,NP0,TP,1608
C1818 2203-000783 C-CERAMIC,CHIP;0.33nF,5%,50V,NP0,TP,1608
C1819 2401-000255 C-AL;100uF,20%,10V,WT,TP,5x11,2mm
C1820 2203-000236 C-CERAMIC,CHIP;0.1nF,5%,50V,NP0,TP,1608
C1821 2203-000236 C-CERAMIC,CHIP;0.1nF,5%,50V,NP0,TP,1608
C1822 2203-000236 C-CERAMIC,CHIP;0.1nF,5%,50V,NP0,TP,1608
C1823 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1824 2401-000414 C-AL;10uF,20%,16V,GP,TP,4x7,5
C1902 2203-000426 C-CERAMIC,CHIP;0.018nF,5%,50V,NP0,TP,160
C1903 2203-000426 C-CERAMIC,CHIP;0.018nF,5%,50V,NP0,TP,160
C1904 2401-000598 C-AL;1uF,20%,50V,GP,TP,4x7,5
C1905 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
C1906 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1908 2203-000681 C-CERAMIC,CHIP;0.027nF,5%,50V,NP0,TP,160
C1909 2401-000598 C-AL;1uF,20%,50V,GP,TP,4x7,5
C1910 2203-000681 C-CERAMIC,CHIP;0.027nF,5%,50V,NP0,TP,160
C1911 2203-001071 C-CERAMIC,CHIP;0.056nF,5%,50V,NP0,TP,160
C1912 2401-000414 C-AL;10uF,20%,16V,GP,TP,4x7,5
C1913 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
C1914 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1915 2401-002075 C-AL;4.7uF,20%,50V,GP,TP,5x11,5
C1916 2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,C1917 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
C1918 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1919 2401-002075 C-AL;4.7uF,20%,50V,GP,TP,5x11,5
C1920 2203-002398 C-CERAMIC,CHIP;22nF,10%,50V,X7R,TP,1608
C1921 2203-000357 C-CERAMIC,CHIP;0.15nF,5%,50V,NP0,TP,1608
C1922 2401-000414 C-AL;10uF,20%,16V,GP,TP,4x7,5
C1923 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
C1924 2203-001086 C-CERAMIC,CHIP;0.005nF,0.25pF,50V,NP0,TP
C1925 2203-000440 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,1608,C1926 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C1927 2203-000140 C-CERAMIC,CHIP;1.5nF,10%,50V,X7R,TP,1608
C201 2203-001656 C-CERAMIC,CHIP;0.47nF,5%,50V,NP0,TP,1608
C202 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608
C203 2203-000257 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,1608
C204 2401-000414 C-AL;10uF,20%,16V,GP,TP,4x7,5
C205 2401-000414 C-AL;10uF,20%,16V,GP,TP,4x7,5
C206 2203-000140 C-CERAMIC,CHIP;1.5nF,10%,50V,X7R,TP,1608
C207 2401-000661 C-AL;2.2uF,20%,50V,GP,TP,5x11,5
C208 2401-001020 C-AL;3.3UF,20%,50V,GP,TP,4X7,5
C209 2203-005148 C-CERAMIC,CHIP;100nF,10%,16V,X7R,TP,1608
C210 2401-000414 C-AL;10uF,20%,16V,GP,TP,4x7,5
Loading...