Samsung DVD-H1080R, DVDH1080, DVD-H1080W User Manual 2

DVD Player

user manual

DVD-H1080 DVD-H1080R DVD-H1080W

AK68-01754K(02)

imagine the possibilities

Thanks you for purchasing this Samsung product. To receive more complete service, please register your product at

www.samsung.com/global/register

precautions

2_ precautions

1. Setting up

- Refer to the identification label located on the rear of your player for its proper operating voltage.

- Install your player in a cabinet with adequate ventilation holes. (7~10cm) Do not block ventilation holes on any of the components for air circulation.

- Do not push the disc tray in by hand.

- Do not stack components.

- Be sure to turn all components off before moving the player.

- Before connecting other components to this player, be sure to turn them off.

- Be sure to remove the disc and turn off the player after use, especially if you are not going to use it for a long time.

- The mains plug is used as a disconnect device and shall stay readily operable at any time.

2. For your safety

- This product utilizes a laser. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

- Do not open covers and do not repair yourself. Refer servicing to qualified personal.

3. Caution

- Your player is not intended for industrial use but for domestic purposes. Use of this product is for personal use only.

Apparatus shall not be exposed to dripping

splashing and no objects filled with liquids such as vases, should be placed on the apparatus.

- Exterior influences such as lightning and static electricity can affect normal operation of this player. If this occurs, turn the player off and on again with the POWER button, or disconnect and then reconnect the AC power cord to the AC power outlet. The player will operate normally.

- When condensation forms inside the player due to sharp changes in temperature, the player may not operate correctly. If this occurs, leave the player at room temperature until the inside of the player becomes dry and operational.

4. Disc

- Do not clean disc using record-cleaning sprays, benzene, thinner, or other volatile solvents that may cause damage to the disc surface.

- Do not touch the disc’s signal surface. Hold by the edges or by one edge and the hole in the center.

- Wipe the dirt away gently; never wipe a cloth back and forth over the disc.

5. Environmental info

- The battery used in this product contains chemicals that are harmful to the environ ment.

- So, dispose of batteries in the proper man ner, according to federal, state, and local regulations.

The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. This license is limited to private non-commercial use by end-user consum ers for licensed contents. No rights are granted for commercial use. The license does not cover any product unit other than this product unit and the license does not extend to any unlicensed product unit or process conforming to ISO/OUR 11172-3 or ISO/OUR 13818-3 used or sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode audio files

conforming to the ISO/OUR 11172-3 or ISO/OUR 13818-3. No rights are granted under this license for product features or functions that do not conform to the ISO/OUR 11172-3 or ISO/OUR 13818-3.

CAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER THAN SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

before you

Accessories

Remote Control

User’s Manual

The accessories which are not supplied are:

Scart Cable

• Component Cable

• Coaxial Cable.

• HDMI-HDMI Cable.

• HDMI-DVI Cable.

•

Install Batteries in the Remote control

1. Open the battery cover on the back of the remote control.

2. Insert two AAA batteries.

Make sure that the polarities (+ and -) are aligned correctly.

3. Replace the battery cover.

If remote control doesn’t operate properly:

- Check the polarity + - of the battery (Dry-Cell)

- Check if the battery is drained.

- Check if remote control sensor is blocked by obstacles.

- Check if there is any fluorescent lighting nearby.

- The rechargeable battery incorporated in this product is not user replaceable.

- For information on its replacement, please contact your service provider.

Batteries for Remote

Control (AAA Size)

start

Video/Audio

Cable

table of

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Setup

General Features . . . . . . . . . . . . . . . . . . . . . . . . . .4

Disc Type and Characteristics . . . . . . . . . . . . . . . .5

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Tour of the Remote Control . . . . . . . . . . . . . . . . . . .7

Connections

Choosing a Connection . . . . . . . . . . . . . . . . . . . . . 8

Basic Functions

Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Using the Search and Skip Functions . . . . . . . . .16

Using the Display Function . . . . . . . . . . . . . . . . .16

Using the Disc and Title Menu . . . . . . . . . . . . . . .17

Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Advanced Functions

Adjusting the Aspect Ratio (EZ View) . . . . . . . . . .18

Selecting the Audio Language . . . . . . . . . . . . . . .18

Selecting the Subtitle Language . . . . . . . . . . . . . .19

Changing the Camera Angle . . . . . . . . . . . . . . . . .19

Using the Bookmark Function . . . . . . . . . . . . . . . .20

Using the Zoom Function . . . . . . . . . . . . . . . . . . .20

Clips Menu for MP3/WMA/JPEG/MPEG4/

CD Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . .21

MP3/WMA/CD Audio Playback . . . . . . . . . . . . . . .21

MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . . . . .22

Playing media files Using the USB

Host Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

CD Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Picture CD Playback . . . . . . . . . . . . . . . . . . . . . . .25

Picture CD Playback for HD JPEG . . . . . . . . . . . .26

Changing Setup Menu

Using the Setup Menu . . . . . . . . . . . . . . . . . . . . . .27

Setting Up the Language Features . . . . . . . . . . . .27

Setting Up the Audio Options . . . . . . . . . . . . . . . . 28

Setting Up the Display Options . . . . . . . . . . . . . . .29

Setting Up the Parental Control . . . . . . . . . . . . . .30

Setting Up the HDMI . . . . . . . . . . . . . . . . . . . . . . .32

Reference

Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . .35

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

content

English _3

setup

4_ setup

General Features

Excellent Sound

Dolby Digital, a technology developed by Dolby Laboratories, provides crystal clear sound reproduction.

Screen

Both regular and widescreen(16:9) pictures can be viewed.

Slow Motion

An important scene can be viewed in slow motion.

1080p Playback

This player upconverts regular DVDs for playback on 1080p TVs.

Parental Control (DVD)

The parental control allows users to set the level necessary to prohibit children from viewing harmful movies such as those with violence, adult subject matter, etc.

Various On-Screen Menu Functions

You can select various languages (Audio/Subtitle) and screen angles while enjoying movies.

Progressive Scan

Progressive scanning creates an improved picture with double the scan lines of a conventional interlaced picture.

EZ VIEW (DVD)

Easy View enables picture adjustment to match your TV's screen size (16:9 or 4:3).

Digital Photo Viewer (JPEG)

You can view Digital Photos on your TV.

Repeat

You can repeat a song or movie simply by pressing the REPEAT button.

MP3/WMA

This unit can play discs created from MP3/WMA files.

MPEG4

This unit can play MPEG4 formats within an avi file.

CD Ripping

This features lets you to copy audio files from disc to USB device into MP3 format. (Only Audio CD (CD DA)).

HDMI (High Definition Multimedia Interface)

HDMI reduces picture noise by allowing a pure digital video/audio signal path from the player to your TV.

Note

- Discs which cannot be played with this player.

• DVD-ROM • DVD-RAM

• CD-ROM • CDV

• CDI • CVD

• CDGs play audio only, not graphics.

- Ability to play back may depend on recording

conditions.

• DVD-R, +R

• CD-RW

• DVD+RW, -RW (V mode)

- The unit may not play certain CD-R, CD-RW and DVD-R due to the disc type or recording

conditions.

COPY PROTECTION

Many DVD discs are encoded with copy protection. Because of this, you should only connect your DVD player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copyprotected DVD discs.

This product incorporates copyright protection technology that is protected by methods claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be auzthorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

PROGRESSIVE SCAN OUTPUTS

(576p,720p,1080p)

“CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE, IN CASE OF 576, 720, 1080 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS REGARDING YOUR TV SET COMPATIBILITY WITH THIS MODEL 576p, 720p, 1080p DVD PLAYER, PLEASE CONTACT SAMSUNG'S CUSTOMER SERVICE CENTER.”

Disc Type and Characteristics

This DVD player is capable of playing the following types of discs with the corresponding logos:

Disc Types

(Logos)

DVD

AUDIO-CD

Disc Markings

Play Region Number

PAL

STEREO

DIGITAL

SOUND

PAL broadcast system in U.K, France, Germany, etc.

Dolby Digital disc

Stereo disc

Digital Audio disc

DTS disc

Recording

Types

Audio

Video

Audio

Disc Size

12 Cm

8 Cm

12 Cm 74 min.

8 Cm 20 min.

Max. Playing Time Characteristic

Single-sided 240 min. Double-sided 480 min

Single-sided 80 min.

Double-sided 160 min.

- DVD contains excellent sound and video due to Dolby Digital and MPEG-2 system.

- Various screen and audio functions can be easi ly selected through the on-screen menu.

- CD is recorded as a Digital Signal with better audio quality, less distortion and less deteriora tion of audio quality over time.

Region Number

Both the DVD player and the discs are coded by region. These regional codes must match in order for the disc to play. If the codes do not match, the disc will not play.

The Region Number for this player is described on the bottom panel of the player.

● SETUP

MP3 disc

You must only insert one DVD disc at a time. Inserting two or more discs will not allow to play them back and it may cause damage to the DVD player.

DivX Certification

DivX, DivX Certified, and associated logos are trademarks of DivXNetworks, Inc and are used under license

English _5

setup

6_ setup

Description

Front Panel Controls

1. STANDBY/ON ( )

When STANDBY/ON is pressed on, the indicator goes

out and the player is turned on.

2. STANDBY Indicator

When the unit is first plugged in, the indicator lights.

3. DISC TRAY

Place the disc here.

Rear Panel

1. DIGITAL AUDIO OUT JACKS

- Use coaxial digital cable to connect to a compatible Dolby Digital receiver.

- Use coaxial digital cable to connect to an A/V Amplifier that contains a Dolby Digital, MPEG2 or DTS decoder.

2. COMPONENT VIDEO OUT JACKS

- Use these jacks if you have a TV with Component Video in jacks. These jacks provide P video.

- If P-SCAN Video Output is selected in Setup Menu, progressive scan mode will work.

- If I-SCAN Video Output is selected in Setup Menu, interlaced scan mode will work.

3. AUDIO OUT JACKS

- Connect to the Audio input jacks of your television or audio/video receiver.

, PB and Y

4. OPEN/CLOSE/Stop ( )

Press to open and close the disc tray, Stops disc play.

5. PLAY/PAUSE ( )

Begin or pause disc play.

4. VIDEO OUT JACK

- Use a video cable to connect to the Video input jack on your television.

5. USB Host

- Connect digital still camera, MP3 player, memory stick, Card reader, or another removable storage devices.

6. HDMI OUT JACK

- Use the HDMI cable to connect this jack to the HDMI jack on your television for the best quality picture.

- If an HDMI cable is connected to an HDMI-compat ible TV, HDMI will be output automatically within 10 seconds.

Note

- Consult your TV User’s Manual to find out if your TV supports Progressive Scan (P-SCAN).

If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the TV’s menu system.

- The HDMI output of this unit can be connected to a DVI jack on a TV or other device using a conver

sion adapter. In this case, it is necessary to use a TV or display with an HDCP-compatible DVI input.

- There may be no image output if the DVD player is connected to a TV or display that is not compatible

with the above format.

- Refer to the TV's instruction manual for detailed information regarding the HDMI terminal.

- See pages 29 ~ 30 to get more information on how to use the setup menu.

● SETUP

Tour of the Remote Control

1 2

4 5 6

7 8

1. DVD Power Button

Turns the power on or off.

2. REPEAT Button

Allows you to repeat play a title, chapter, track or disc

3. DISC MENU Button

Brings up the Disc menu.

4. Bookmark Button

5. SEARCH Buttons (

Allow you to search forward/backward through a disc.

6. STOP Button ( )

7. SUBTITLE (

8. MENU Button

Brings up the DVD player’s menu.

9. AUDIO (√) Button

Use this button to access various audio functions on a disc.

10. ENTER/π/†,√/® Buttons

This button functions as a toggle switch.

11. INFO Button

Displays the current disc mode.

12. OPEN/CLOSE ( ) Button

To open and close the disc tray.

13. REPEAT A-B Butoon

Allows you to repeat play a chosen section (A-B) on a

disc.

14. USB button

15. PAUSE Button (

Pause disc play.

16. PLAY Button ( )

Begin disc play.

17. SKIP Buttons (

Use to skip the title, chapter or track.

18. RETURN Button

Returns to a previous menu.

19. TITLE MENU (®) Button

Brings up the Title menu.

20. CANCEL Button

Use to remove menus or status displays from the

screen.

) Button

)

English _7

connections

8_ connections

Choosing a Connection

The following shows examples of connections commonly used to connect the DVD player with a TV and other components.

Before Connecting the DVD Player

- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.

- Refer to the user’s manual of the additional components you are connecting for more information on those particular components.

Connecting to a TV (VIDEO CVBS)

Using video/audio cables, connect the VIDEO (yellow)/ AUDIO (red and white) OUT terminals on the rear of the

DVD player to the

IN terminals of TV.

Turn on the DVD player and TV.

Press the input selector on your TV remote control until the Video signal from the DVD player appears on the TV screen.

VIDEO (yellow)/AUDIO (red and white)

RED

YELLOW

WHITE

Audio

Video Cable

Cable

YELLOW

WHITE

RED

Note

- Noise may be generated if the audio cable is too close to the power cable.

- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 13 to 14)

- The number and position of terminals can vary depending on your TV set. Please refer to the user's manual of the TV.

- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal of the DVD player.

Connection to a TV (Interlace)

- Connecting to your TV using Component video cables.

- You will enjoy high quality and accurate color reproduction images. Component video separates the pic ture element into black and white(Y), blue(PB), red(PR) signals to present clear and clean images. (Audio signals are delivered through the audio output.)

Using component video cables (not included), connect the COMPONENT VIDEO OUT terminal on the rear of the DVD player to the

COMPONENT IN terminal of TV.

Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of TV. Turn on the

DVD player and TV.

Press the input selector on your TV remote control until the Component signal from the DVD player appears on the TV screen.

RED

WHITE

RED

WHITE

Audio Cable

BLUE

GREEN

BLUE

GREEN

Component cable

● CONNECTIONS

Set the Video Output to I-SCAN in the Display Setup menu. (See pages

Note

- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 13 to 14)

- The component terminal of TV can be marked by “R-Y, B-Y, Y” or “Cr, Cb, Y” instead of “P depending on the manufacturer. The number and position of terminals can vary depending on the TV set. Please refer to the user's manual of the TV.

29-30)

, PB, Y”

English _9

connections

10_ connections

Connection to a TV (Progressive)

Using component video cables (not included), connect the COMPONENT VIDEO OUT terminal on the rear of the

DVD player to the

Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of TV. Turn on the

DVD player and TV.

Press the input selector on your TV remote control until the Component signal from the DVD player appears on the TV screen.

Set the Video Output to P-SCAN in the Display Setup menu. (See pages 29-30)

COMPONENT IN terminal of TV.

WHITE

GREEN

BLUE

Component cable

RED

Audio Cable

WHITE

RED

BLUE

To see the progressive video output,

- Consult your TV User’s Manual to find out if your TV supports Progressive Scan. If Progressive

You need a TV set supporting the progressive scan

Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the TV’s

input function. And you have to set up the TV

menu system.

- Depending on your TV, the connection method may differ from the illustration above.

Note

- What is "Progressive Scan"?

Progressive scan has twice as many scanning lines as the interlace output method has. Progressive

scanning method can provide better and clearer picture quality.

Connecting to a TV with DVI Jack

Using an HDMI-DVI cable (not included), connect the

HDMI OUT terminal on the rear of the DVD player to the DVI IN terminal of your TV.

Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of your TV.

Turn on the DVD player and TV.

Press the input selector on your TV remote control until the DVI signal from the DVD player appears on your TV screen.

Connecting to a TV with HDMI Jack

Using the HDMI-HDMI cable connect the HDMI OUT terminal on the rear of the DVD player to the of your TV.

HDMI IN terminal

RED

WHITE

Audio Cable

WHITE

● CONNECTIONS

HDMI-DVI cable

Press the input selector on your TV remote control until the HDMI signal from the DVD player appears on your TV screen.

HDMI VIDEO Specifications

- Depending on your TV, certain HDMI output resolutions may not work.

- Please refer to the user's manual of your TV.

- If HDMI or HDMI-DVI cable is plugged into TV, the DVD player’s output is set to HDMI/DVI within 10

-seconds.

- If you set the HDMI output resolution 720p,1080p or 1080i, HDMI output provides better picture

-quality.

- If you connect an HDMI cable between Samsung TV and this DVD player, you can operate this DVD player using your TV remote control. This is only available with Samsung TVs that support Anynet+(HDMI-CEC). (See page 32).

- If your TV has an

logo, then it will Supports the Anynet+ Function.

HDMI cable

English _11

connections

12_ connections

• HDMI (High Definition Multimedia Interface)

HDMI is an interface to enable the digital transmission of video and audio data with just a single connector. Using HDMI, the DVD player transmits a digital video and audio signal and displays a vivid picture on a TV having an HDMI input jack.

• HDMI connection description

HDMI connector - Both uncompressed video data and

digital audio data (LPCM or Bit Stream data).

- Though the player uses a HDMI cable, the player outputs only a pure digital signal to the TV.

- If TV does not support HDCP (High-bandwidth Digital content protection), snow noise appears on the screen.

• Why does Samsung use HDMI?

Analog TVs require an analog video/audio signal. However, when playing a DVD, the data transmitted to a TV is digital. Therefore either a digital-to-analog converter (in the DVD player) or an analog-to-digital converter (in the TV) is required. During this conver sion, the picture quality is degraded due to noise and signal loss. DVI technology is superior because it requires no D/A conversion and is a pure digital sig nal from the player to your TV.

• What is the HDCP?

HDCP (High-bandwidth Digital Content Protection) is a system for protecting DVD content outputted via DVI from being copied. It provides a secure digital link between a video source (PC, DVD. etc) and a display device (TV, projector . etc). Content is encrypted at the source device to prevent unauthor ized

+ 28 hidden pages