Samsung DVD-C350K User Manual

DVD Player

User Manual

imagine the possibilities

Thank you for purchasing this Samsung product. To receive more complete service, please register your product at

DVD-C450K

DVD-C450 DVD-C360

DVD-C350K

DVD-C350

AK68-01918A

www.samsung.com/global/register

ENGLISH

precautions

1. Setting up

- Refer to the identification label located on the rear of your player for its proper operating voltage.

- Install your player in a cabinet with adequate ventilation holes. (7~10cm) Do not block ventilation holes on any of the components for air circulation.

- Do not push the disc tray in by hand.

- Do not stack components.

- Be sure to turn all components off before moving the player.

- Before connecting other components to this player, be sure to turn them off.

- Be sure to remove the disc and turn off the player after use, especially if you are not going to use it for a long time.

- The mains plug is used as a disconnect device and shall stay readily operable at any time.

2. For your safety

- This product utilizes a laser. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

- Do not open covers and do not repair yourself. Refer servicing to qualified personal.

3. Caution

- Your player is not intended for industrial use but for domestic purposes. Use of this product is for personal use only.

- Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

- Exterior influences such as lightning and static electricity can affect normal operation of this player. If this occurs, turn the player off and on again with the POWER button, or disconnect and then reconnect the AC power cord to the AC power outlet. The player will operate normally.

- When condensation forms inside the player due to sharp changes in temperature, the

player may not operate correctly. If this occurs, leave the player at room temperature until the inside of the player becomes dry and operational.

4. Disc

- Do not use record-cleaning sprays, benzene, thinner, or other volatile solvents that may cause damage to the disc surface.

- Do not touch the disc’s signal surface. Hold by the edges or by one edge and the hole in the center.

- Wipe the dirt away gently; never wipe a cloth back and forth over the disc.

5. Environmental info

- The battery used in this product contains chemicals that are harmful to the environment.

- So, dispose of batteries in the proper man ner, according to federal, state, and local regulations.

The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are granted for commercial use. The license does not cover any product unit other than this product unit and the license does not extend to any unlicensed product unit or process conforming to ISO/OUR 11172-3 or ISO/OUR 13818-3 used or sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode audio files conforming to the ISO/OUR 11172-3 or ISO/OUR 13818-3. No rights are granted under this license for product features or functions that do not conform to the ISO/OUR 11172-3 or ISO/OUR 13818-3.

CAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER THAN SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

Contents

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Setup

General Features . . . . . . . . . . . . . . . . . . . . . . 2

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Tour of the Remote Control . . . . . . . . . . . . . . 4

Connections

Choosing a Connection . . . . . . . . . . . . . . . . . 5

Basic Functions

Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . 6

Using the Search and Skip Functions . . . . . . 6

Using the Display Function . . . . . . . . . . . . . . 6

Using the Disc Menu and Title Menu . . . . . . . 6

Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Slow Play

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Advanced Functions

Adjusting the Aspect Ratio (EZ View) . . . . . . . 7

Selecting the Audio Language . . . . . . . . . . . . 7

Selecting the Subtitle Language . . . . . . . . . . . 7

Changing the Camera Angle . . . . . . . . . . . . . . 7

Using the Bookmark Function . . . . . . . . . . . . 7

Using the Zoom Function . . . . . . . . . . . . . . . . 8

setup

General Features

Excellent Sound

Dolby Digital, a technology developed by Dolby Laboratories, provides crystal clear sound reproduction.

Screen

Both regular and widescreen(16:9) pictures can be viewed.

Slow Motion

An important scene can be viewed in slow motion.

Parental Control (DVD)

The parental control allows users to set the level necessary to prohibit children from viewing harmful movies such as those with violence, adult subject matter, etc.

Various On-Screen Menu Functions

You can select various languages (Audio/Subtitle) and screen angles while enjoying movies.

Progressive Scan

Progressive scanning creates an improved picture

Clips Menu for MP3/WMA/JPEG/MPEG4 CD Audio

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Folder Selection . . . . . . . . . . . . . . . . . . . . . . . 8

MP3/WMA/CD Audio Playback. . . . . . . . . . . . 8

MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . . 9

Playing media files Using the USB Host

Feature (Only DVD-C360,C450,C450K) . . . . . . . 9

CD Ripping (Only DVD-C360,C450,C450K) . . . 10

Picture CD Playback . . . . . . . . . . . . . . . . . . . 10

Karaoke Function

Karaoke Function (Only DVD-C450K,C350K) . . 10

Changing Setup Menu

Using the Setup Menu . . . . . . . . . . . . . . . . . 11

Setting Up the Language Features . . . . . . . . 11

Setting Up the Audio Options . . . . . . . . . . . . 11

Setting Up the Display Options. . . . . . . . . . . 11

Setting Up the Parental Control . . . . . . . . . . 11

Setting Up the Divx . . . . . . . . . . . . . . . . . . . . 12

Reference

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . 12

Specifications . . . . . . . . . . . . . . . . . . . . . . . . 12

with double the scan lines of a conventional interlaced picture.

EZ VIEW (DVD)

Easy View enables picture adjustment to match your TV's screen size (16:9 or 4:3).

Digital Photo Viewer (JPEG)

You can view Digital Photos on your TV.

Repeat

You can repeat a song or movie simply by pressing the REPEAT button.

MP3/WMA

This unit can play discs created from MP3/WMA files.

MPEG4

This unit can play MPEG4 formats within an avi file.

CD Ripping (Only DVD-C360,C450,C450K)

This feature lets you copy audio files from discs to USB device into MP3 format. (only audio CD (CD DA)

Note

▼

▼ ▼

▼

▼ ▼

▼

▼ ▼

▼

- Discs which cannot be played with this player.

• DVD-ROM • DVD-RAM

• CD-ROM • CDV

• CDI • CVD

• CDGs play audio only, not graphics.

- Ability to play back may depend on

recording conditions.

• DVD-R, +R

• CD-RW

• DVD+RW, -RW (V mode)

- The unit may not play certain CD-R, CD-RW and DVD-R due to the disc type or record

ing conditions.

COPY PROTECTION

Many DVD discs are encoded with copy protection. Because of this, you should only connect your DVD player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copy-protected DVD discs. This product incorporates copyright protection technology that is protected by methods claims of certain U.S. patents and other intel-

Disc Markings

PAL

Play Region Number

PAL broadcast system in U.K, France, Germany, etc.

Dolby Digital disc

lectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be auzthorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

PROGRESSIVE SCAN OUTPUTS (576p)

“CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE, IN CASE OF 576 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS REGARDING YOUR TV SET COMPATIBILITY WITH THIS MODEL 576p DVD PLAYER, PLEASE CONTACT SAMSUNG'S CUSTOMER SERVICE CENTER.”

Region Number

Both the DVD player and the discs are coded by region. These regional codes must match in order for the disc to play. If the codes do not match, the disc will not play.

The Region Number for this player is described on the rear panel of the player.

Descriptions

Front Panel Controls

DVD-C450K

DVD-C450

DVD-C360

DVD-C350K

5 6

STEREO

DIGITAL

SOUND

Stereo disc

Digital Audio disc

DTS disc

MP3 disc

DivX Certification

DivX, DivX Certified, and associated logos are trademarks of

DVD-C350

5 6

DivXNetworks, Inc and are used under license. DivX Certified to play DivX video.

1. DISC TRAY

Place the disc here.

2. DISPLAY

Operation indicators are displayed here.

3. OPEN/CLOSE/STOP ( )

Press to open and close the disc tray

4. STOP (■

(

)

Only DVD-C450K,C450)

Stop disc play.

5. PLAY/PAUSE

( )

Play or pause the disc / Stops Disc Play

6. POWER ON/OFF ( )

Turn On/Off the DVD Player

Tour of the Remote Control

DVD-C450K DVD-C450 DVD-C360

1 2

3 4

5 6 7

1. DVD POWER Button

Turns the power on or off.

2. REPEAT Button

Allows you to repeat play

a title,

chapter, track, or disc.

3. DISC MENU Button

Brings up the Disc menu.

4. BOOKMARK

Quickly find bookmark sec-

tions of a DVD.

5. SEARCH Buttons ( / )

Allow you to search forward/

back ward through a disc.

6. STOP Button ( )

7. SKIP Buttons ( / )

Use to skip the title, chapter

or track

8. MENU Button

Brings up the DVD player’s

menu.

9. ENTER /π/†,√/® Buttons

This button functions as a

toggle switch.

10. AUDIO Button (√)

Use this button to access

various audio functions on a disc.

7. USB HOST

(Only DVD-C360,C450,C450K)

Connect digital still camera, MP3 player, mem-

ory stick, Card reader, or another removable

storage devices.

8. MIC 1/2

(Only DVD-C350K,C450K)

Connect Microphone for karaoke functions.

9. MICROPHONE VOLUME

(Only DVD-C450K)

Use to adjust microphone volume level. Use the

button by pressing it. Turn it to the left or right to

control the volume.

11. INFO Button

Displays the current disc

mode.

12. OPEN/CLOSE ( ) Button

To open and close the disc

tray.

13. REPEAT A-B Button

Allows you to repeat A-B

disc.

14. USB Button

15. VIDEO SEL. Button

Selects video output for

mats.

16. PLAY/PAUSE Button ( )

Begin/Pause disc play.

17. SUBTITLE Button (π)

18. RETURN Button

Returns to a previous menu.

19. TITLE MENU Button (®)

Brings up the Title menu.

20. KARAOKE Button († ) (Only DVD-C450K) Use to begin Karaoke func-

tions.

21. CANCEL Button

Use to remove menus or

status displays from the screen.

DVD-C350K DVD-C350

1. DVD POWER Button

Turns the power on or off.

2. REPEAT Button

Allows you to repeat play a

title, chapter, track, or disc.

3. DISC MENU Button

Brings up the Disc menu.

4. BOOKMARK

Quickly find bookmark sections

of a DVD.

5. STOP Button ( )

6. SKIP Buttons ( / )

Use to skip the title, chapter

or track

7. MENU Button

Brings up the DVD player’s

menu.

8. ENTER/π/†,√/® Buttons

This button functions as a

toggle switch.

9. AUDIO Button (√)

Use this button to access vari

ous audio functions on a disc.

10. INFO Button

Displays the current disc mode.

11. OPEN/CLOSE ( ) Button

To open and close the disc tray.

12. REPEAT A-B Button

Allows you to repeat A-B disc.

13. ZOOM Button

Enlarges the DVD Picture.

14. VIDEO SEL. Button

Selects video output for mats.

15. SEARCH Buttons ( / )

Allow you to search forward/ back ward through a disc.

16. PLAY/PAUSE Button ( )

Begin/Pause disc play.

17. SUBTITLE Button (π)

18. RETURN Button

Returns to a previous menu.

19. TITLE MENU Button (®)

Brings up the Title menu.

20. CANCEL Button

Use to remove menus or status displays from the

screen.

21. KARAOKE Button (†) (Only DVD-C350K)

Use to begin Karaoke func

tions.

connections

Choosing a Connection

The following shows examples of connections commonly used to connect the DVD player with a TV and other components.

Before Connecting the DVD Player

- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.

- Refer to the user’s manual of the additional components you are connecting for more informa tion on those particular components.

A. Connecting to a TV (VIDEO)

- Using video/audio cables, connect the VIDEO (yellow)/AUDIO (red and white) OUT terminals on the rear of the DVD player to the VIDEO (yellow)/AUDIO (red and white) IN terminals of TV.

- Turn on the DVD player and TV.

- Press the input selector on your TV remote control until the Video signal from the DVD player appears on the TV screen.

Note

- Noise may be generated if the audio cable is placed too close to the power cable.

- If you want to connect to an Amplifier, please refer to the Amplifier connection section below.

- The number and position of terminals can vary depending on your TV set. Please refer to the user's manual of the TV.

- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal of the DVD player.

- If you press the VIDEO SEL. button when DVD Player is in stop mode or no disc is inserted, the Video Output mode changes in the following sequence: (I-SCAN ➝ P-SCAN ).

B. Connection to an Audio System (2 Channel Amplifier, Dolby Digital,MPEG2 or DTS Amplifier)

- Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of the Amplifier. If using a coaxial cable, connect the DIGITAL AUDIO OUT (COAXIAL) terminal on the rear of the DVD player to the DIGITAL AUDIO IN (COAXIAL) terminal of the Amplifier.

- Using the video signal cable(s), connect the VIDEO or COMPONENT terminals on the rear of the DVD player to the VIDEO or COMPONENT terminals of your TV.

- Turn on the DVD player, TV, and Amplifier.

- Press the input select button of the Amplifier to select external input in order to hear sound from the DVD player.

Refer to your Amplifier's user manual to set the Amplifier's audio input.

C. Connections to a TV Interlace / Progressive

- Using Component video cables (not included), connect the COMPONENT VIDEO OUT (PR, PB and Y) jacks on the rear of the DVD player to the COMPONENT IN (PR, PB and Y) jacks of your TV.

- Using the audio cables, connect the DVD player to the AUDIO (red and white) IN terminals of TV. Turn on the DVD player and TV.

- Set the Video Output to

SEL. button to change the Video Output mode.

I-SCAN/P-SCAN in the Display Setup menu. You can use the VIDEO

AUDIO (red and white) OUT terminals on the rear of the

- Press the input selector on your TV remote control until the Component signal from the DVD player appears on the TV screen.

- Set the Video Output to

SEL. button to change the Video Output mode.

Note

- What is "Progressive Scan"? Progressive scan has twice as many scanning lines as the interlace output method has. Progressive scanning method can provide better and clearer picture quality.

WHITE

RED

AUDIO CABLE

WHITE

RED

I-SCAN/P-SCAN in the Display Setup menu. You can use the VIDEO

VIDEO CABLE

YELLOW

COAXIAL CABLE

BLUE GREEN

RED

YELLOW

RED BLUE GREEN

COMPONENT CABLE

2-Channel stereo ampilﬁer,

Dolby digital or

DTS ampliﬁer

RED

WHITE

RED

WHITE

AUDIO CABLE

basic functions

Playing a Disc

Before Play

- Turn on your TV and set it to the correct Video Input by pressing TV/VIDEO button on the TV remote control.

- If you connected an external Audio System, turn on your Audio System and set it to the correct Audio Input.

After plugging in the player, the first time you press the DVD POWER button, this screen comes up: If you want to select a language, press a π/† button then press ENTER (This screen will only appear when you plug in the player for the first time.) If the language for the startup screen is not set, the settings may change whenever you turn the power on or off. Therefore, make sure that you select the language you want to use. Once you select a menu language, you can change it by

pressing the ■ / button on the front panel of the unit for more than 5 seconds with no disc in the unit. Then the SELECT MENU LANGUAGE window appears again where you can reset your preferred language.

Using the Search and Skip Functions

During play, you can search quickly through a chapter or track, and use the skip function to jump to the next selection.

Searching through a Chapter or Track

During play, press the SEARCH ( or ) button on the remote control for more than 1 second.

DVD 2X, 4X, 64X, 128X

VCD 4X, 8X

CD 2X, 4X, 8X

Skipping Tracks

During play, press the SKIP ( or ) button.

- When playing a DVD, if you press the SKIP (

press the SKIP ( ) button, it moves to the beginning of the chapter. One more press makes it move to the beginning of the previous chapter.

- When playing a VCD or a CD, if you press the SKIP ( ) button, it moves to the next track. If

you press the SKIP ( ) button, it moves to the beginning of the track. One more press makes it move to the beginning of the previous track.

- If a track exceeds 15 minutes when playing a VCD and you press the

ward 5 minutes. If you press the button, it moves backward 5 minutes.

Using the Display Function

When Playing a DVD/VCD/MPEG4

1. During play, press the INFO button on the remote control.

2. Press the

- When playing VCD, the Disc Menu may notwork.

3. Press the √/® buttons to make the desired setup and then press the ENTER button.

4. To make the screen disappear, press the INFO button.

π/† buttons to select the desired item.

Note

- The speed marked in this function may be different from the actual playback speed.

- No sound is heard during search mode (Except CD).

) button, it moves to the next chapter. If you

button, it moves for-

To access the desired title when there is more than one in the disc. For example, if there is more than one movie on a DVD, each movie will be identified.

Most DVD discs are recorded in chapters so that you can quickly find a specific passage.

Allows playback of the film from a desired time. You must enter the starting time as a reference. The time search function does not operate on some disc.

Refers to the subtitle languages available in the disc. You will be able to choose the subtitle languages or, if you prefer, turn them off from the screen. A DVD disc can have up to 32 differ ent subtitles.

Enter and press the function and Zoom. Refers to the language of the film soundtrack. In the example, the soundtrack is played in English 5.1CH. A DVD disc can have up to eight different soundtracks. Some DVD discs are have more angle function from any picture. Bookmark function make you easily and quickly to find a track or chapter from DVD or CD. The EZ View function is use for changing the aspect ratio in DVD. The ZOOM function is use for Enlarge DVD Picture

√/®

buttons to access the desired Audio, Angle, Bookmark, EZ View

Using the Disc and Title Menu

During stop mode of a DVD disc, press the DISC MENU/TITLE MENU button on the remote control.

Note

- The Disc Menu or Title Menu may not work. Depending on the disc.

- You can also use the Disc Menu, using the DISC MENU button on the remote control.

- Title Menu will only be displayed if there are at least two titles in the disc.

Repeat Play

Repeat the current track, chapter, title, a chosen section (A-B), or all of the disc.

When playing a DVD/VCD

Press the REPEAT buttons to select Chapter, Title, Track, Disc or Repeat : Off

- DVD repeats play by chapter or title, VCD repeat play by disc or track.

- Chapter : repeats the chapter that is playing.

- Title : repeats the title that is playing.

- Disc : repeats the disc that is playing.

- Repeat : Off

- Track : repeats the track that is playing.

Using the A-B Repeat function

1. Press the REPEAT A-B button at the point where you want repeat play to start (A).

2. Press the

3. To return to normal play, press the REPEAT A-B then press the ENTER button until the display

Note

- A-B REPEAT allow you to set point (B) directly after point (A) has been set.

- Depending on the disc, the Repeat function may not work.

- When playing VCD, the Disc Menu may not work.

REPEAT A-B button at the point where you want the repeat play to stop (B).

- To return to normal play, press the CANCEL button.

shows Repeat : Off

Slow Play

This feature allows you to repeat scenes slowly containing sports, dancing, musical instruments being played etc., so you can study them more closely.

When playing a DVD/VCD

1. During play, press the PLAY/PAUSE ( ) button.

2. Press the

SEARCH ( ) button to choose the play speed between 1/2, 1/4, 1/8 and 1/16 of

normal during PAUSE.

advanced functions

Adjusting the Aspect Ratio (EZ View)

To play back using aspect ratio (DVD)

1. During play, press the INFO button on the remote control.

2. Press the

3. Press the √/® buttons to select EZ View, then press the ENTER button.

If you are using a 16:9 TV

For 16:9 aspect ratio discs

- NORMAL WIDE

- SCREEN FIT

- ZOOM FIT

- VERTICAL FIT

For 4:3 aspect ratio discs

- NORMAL SCREEN

- SCREEN FIT

- ZOOM FIT

Note

This function may behave differently depending on the type of disc.

You can select a desired audio language quickly and easily with the AUDIO button.

Using the AUDIO/ √ button (DVD/VCD/MPEG4)

1. Press the AUDIO/√ button. The Audio changes when the button is pressed repeatedly. The

π/† buttons to select Shortcut, then press the ENTER button.

- Each time you press the √/® button, the screen size changes. For graphics of the screen sizes

and the sequence in which the sizes change, see the next column.

If you are using a 4:3 TV

For 16:9 aspect ratio discs

- 4:3 Letter Box

- 4:3 Pan Scan

- SCREEN FIT

- ZOOM FIT

For 4:3 aspect ratio discs

- NORMAL SCREEN

- SCREEN FIT

- ZOOM FIT

Selecting the Audio Language

audio languages are represented by abbreviations. Press Audio /√ button at remocon repeatedly to select the desired Audio on MPEG4 then press the

ENTER.

Note

- This function depends on audio languages are encoded on the disc and may not work.

- A DVD disc can contain up to 8 audio languages.

Selecting the Subtitle Language

You can select a desired subtitle quickly and easily with the SUBTITLE (π) button.

Using the SUBTITLE / π button (DVD/MPEG4)

1. Press the SUBTITLE / π subtitle changes when the button is pressed repeatedly.

Press SUBTITLE / π MPEG4 then press the ENTER.

2. To remove the

Note

- You have to change the desired subtitle in the Disc Menu, according to discs. Press the DISC MENU button.

- This function depends on what subtitles are encoded on the disc and may not work on all DVDs.

- A DVD disc can contain up to 32 subtitle languages.

button. The subtitle languages are represented by abbreviations. The

button at remocon repeatedly to select the desired subtitle language on a

SUBTITLE icon, press the SUBTITLE / π button.

Changing the Camera Angle

When a DVD contains multiple angles of a particular scene, you can use the ANGLE function.

Using the ANGLE button (DVD)

If the disc contains multiple angles, the ANGLE appears on the screen.

1. During play, press the INFO button on the remote control.

2. Press the

3. Press the √/® buttons to select Angle, then press the ENTER button.

4. Press the √/® buttons on the remote control to select the desired angle.

π/† buttons to select Shortcut. then press the ENTER button.

Note

- If the disc has only one angle, this feature won’t work. Currently, very few discs have this feature.

- Depending on the disc, these functions may not work.

Using the Bookmark Function

This feature lets you bookmark sections of a DVD or VCD (Menu Off mode) so you can quickly ﬁnd them at a later time.

Using the Bookmark Function DVD/VCD

1. During play, press the INFO button on the remote control.

2. Press the

3. Press the √/® buttons to select Bookmark then press the ENTER button.

4. When you reach the scene you want to mark, press-the

π/† buttons to select Shortcut, then press the ENTER button

12 scenes at a time.

Note

- Depending on a disc, the Bookmark function may not work.

- When playing VCD, the Disc Menu may not work.

ENTER button. You can bookmark up to

Recalling a Marked Scene

001/004

O

1~3. The first 1~3 steps are the same as those for “Using the Bookmark Function”.

4. Press the √/® buttons to select a marked scene.

5. Press the PLAY/PAUSE ( ) button to skip to the marked scene.

Clearing a Bookmark

1~3. The first 1~3 steps are the same as those for “Using the Bookmark Function”.

4. Press the √/® buttons to select the bookmark number you want to delete.

5. Press the CANCEL button to delete a bookmark number.

Using the Zoom Function

- Using the Zoom Function (DVD/VCD) (DVD-C350,C350K)

1. During play, press the ZOOM button on the remote control.

- Using the Zoom Function (DVD/VCD) (DVD-C360,C450,C450K)

1. During play, press the INFO button on the remote control.

2. Press the

3. Press the √/® buttons to select Zoom, then press the ENTER button.

π/† buttons to select Shortcut, then press the ENTER button

- During DVD/VCD play, press ENTER to zoom in 2X/3X/4X/ Normal in order.

Clips Menu for MP3/WMA/JPEG/MPEG/CD Audio

CD Audio or discs with MP3/WMA/JPEG contain individual songs and/or pictures that can be organized into folders as shown below. They are similar to how you use your computer to put files into different folders.

Open the disc tray. Place the disc on the tray. Close the tray. and the tray closes.

Folder Selections

The folder can be selected in Stop or Play mode.

- To select the Parent Folder Press the RETURN button to go to parent folder, or press the

press ENTER to go to the parent folder.

π/† buttons to select “..” and

MP3/WMA/CD Audio Playback

1. Open the disc tray. Place the disc on the tray. Close the tray.

- Only one kind of file is played back when a disc or a folder contains both MP3 and WMA files.

2. Press the

- Press

π/† buttons to select a song file.

ENTER to begin playback of the song file.

Repeat/Random playback

Press the REPEAT button to change the playback mode. There are four modes, such as Off, Track, Folder and Random.

- Off: Normal Playback

- Track: Repeats the current song file.

- Folder: Repeats the song files which have the same extension in the current folder.

- Random: Song files which have the same extension will be played in random order. To resume normal play, press the

CANCEL button.

CD-R MP3/WMA file

When you record MP3 or WMA files on CD-R, please refer to the following.

- Your MP3 or WMA files should be ISO 9660 or JOLIET format.

ISO 9660 format and Joliet MP3 or WMA files are compatible with Microsoft's DOS and

Windows, and with Apple's Mac.This format is the most widely used.

- When naming your MP3 or WMA files, do not exceed 8 characters, and enter “.mp3, .wma” as the file extension.

General name format : Title.mp3. or Title.wma. When composing your title, make sure that you

use 8 characters or less, have no spaces in the name, and avoid the use of special characters including: (.,/,\,=,+).

- Use a decompression transfer rate of at least 128 Kbps when recording MP3 files.

Sound quality with MP3 files basically depends on the rate of compression/ decompression you

choose. Getting CD audio sound requires an analog/digital sampling rate, that is conversion to MP3 format, of at least 128 Kbps and up to 160 Kbps. However, choosing higher rates, like Kbps or more, only rarely give better sound quality. Conversely, files with decompression rates below 128 Kbps will not be played properly.

- Use a decompression transfer rate of at least 64Kbps when recording WMA files.

Sound quality with WMA files basically depends on the rate of compression/decompression you

choose. Getting CD audio sound requires an analog/digital sampling rate, that is conversion to WMA format, of at least 64Kbps and up to Kbps. Conversely, files with decompression rates below 64Kbps or over Kbps will not be played properly.

- Do not try recording copyright protected MP3 files.

Certain "secured" files are encrypted and code protected to prevent illegal copying. These files

are of the following types: Windows Media (registered trade mark of Microsoft Inc) and SDMITM (registered trade mark of The SDMI Foundation). You cannot copy such files.

- Important:

The above recommendations cannot be taken as a guarantee that the DVD player will play MP3

recordings, or as an assurance of sound quality. You should note that certain technologies and methods for MP3 file recording on CD-Rs prevent optimal playback of these files on your DVD player (degraded sound quality and in some cases, inability of the player to read the files).

- This unit can play a maximum of 500 files and 500 folders per disc.

MPEG4 Playback

MPEG4 Play Function

MPEG4 is a compressed video format designed to deliver DVD quality video at lower data rates and smaller file sizes. Types of MPEG4 files are DivX or Xvid. These files have an .avi extension. AVI files are used to contain the audio and video data. This unit can only play AVI format files with the “.avi” extension.

1. Open the disc tray. Place the disc on the tray. Close the tray.

2. Press the

Repeat playback

Press the REPEAT button to change playback mode. There are 3 modes, such as Track, Folder and Off.

- Track : repeats the track that is playing.

- Folder : repeats the AVI files which have the same extension in the current folder.

- Off

π/† buttons to select an avi file (DivX/XviD) and then press ENTER button.

MPEG4 Function Description

Function Description

Skip

( or )

Slow motion

Play

- These functions may not work depending on MPEG4 file.

CD-R AVI file

This unit can play the following video compression formats within the AVI file format:

- DivX 3.11 contents

- DivX 4 contents (Based on MPEG-4 Simple Profile)

- DivX 5 contents (MPEG-4 simple profile plus additional features such as bi-directional frames. Qpel and GMC are also supported.)

- XviD MPEG-4 compliant Contents.

This unit supports all resolutions up to maximum below.

720 x 480 @30fps 720 x 576 @25fps : Maximum bit rate :4Mbps

Note

• Some MPEG-4 files created on a personal computer may not be play back. That is why Codec Type, Version and Higher resolution over specification is not supported.

• This unit supports CD-R/RW written in MPEG4 in accordance with the “ISO9660 format”.

During play, press the or button, it moves forward or backward 5 minutes.

During play, press the SEARCH ( or ) button and press again to search at a faster speed. Allows you to search at a faster speed in an AVI file. (2X, 4X, 8X)

Allows you to search at a slower speed in an AVI file. (1/2, 1/4, 1/8, 1/16)

DivX5

Playing Media File Using the USB Host feature

(Only DVD-C360, C450,C450K)

You can enjoy the media files such as pictures, movies and tunes saved in an MP3 player, USB memory or digital camera in high audio by connecting the storage device to the USB port of the DVD Player.

Using the USB HOST feature

1. Connect the USB device to the USB port on the front of the unit.

2. Press the

Note

• Each time the USB button on the remote control is pressed, a frame of the USB device

• “

• When playing DVD or CD and USB inserted, “Press USB to select device” appear at the top

• USB MENU screen appears on the TV screen and the saved file is played.

Skip Forward/Back

During playback, press the ( / ) button.

• When there is more than one file, when you press the

Safe USB Removal

To prevent damage to the memory stored in the USB device, perform safe removal before disconnecting the USB cable.

- Press the STOP ( ) button

- Remove the USB cable.

Fast playback

To play back the disc at a faster speed, press ( / ) during playback.

• Each time you press either button, the playback speed will change as follows:

Compatible Devices

1. USB devices that support USB Mass Storage v1.0. (USB devices that operate as a removable

2. MP3 Player: Flash type MP3 player.

3. Digital camera: Cameras that support USB Mass Storage v1.0.

4. USB Flash Drive: Devices that support USB2.0 or USB1.1.

• You may experience a difference in playback quality when you connect a USB1.1 device.

5. USB card Reader: One slot USB card reader and Multi slot USB card reader

• Depending on the manufacturer. the USB card reader may not be supported.

• If you install multiple memory devices into a multi card reader, you may experience problems.

6. If you use a USB extension cable, the USB device might not be recognized.

• CBI (Control/Bulk/Interrupt) is not supported.

• Digital Cameras that use PTP protocol or require additional program installation when connected to a PC are not supported.

π/† buttons to select a file in USB. Press ENTER to Open file.

selection will appear.

USB” appears on the display screen.

left corner for a moment.

button, the next file is selected. button, the previous file is selected.

➞ 4x ➞ 8x.

disk in Windows (2000 or later) without additional driver installation.)

• Cameras that operate as a removable disk in Windows (2000 or later) without additional driver installation.

• A device using NTFS file system is not supported. (Only FAT 16/32 (File Allocation Table 16/32) file system is supported.)

• Some MP3 players, when connected to this product,may not operate depending on the sector size of their file system.

• The USB HOST function is not supported if a product that transfers media files by its manufacturer-specific program is connected.

• Does not operate with Janus enabled MTP (Media Transfer Protocol) devices.

• The USB host function of this product does not support all USB devices.

CD Ripping (Only DVD-C360, C450, C450K)

This feature lets you to copy audio files from disc to USB device into MP3 format.

1. Open the dics tray. Place the Audio CD(CD DA) disc on the tray, and close the tray. Connect the USB device to the USB port on the front of the unit.This screen will be displayed. Press ENTER to select disc.

2. Press the RETURN button to display the ripping screen.

3. Press the π/† buttons, then press the ENTER button to select files for ripping.

- To deselect files, press ENTER button again.

4. Press the ® and † button to select START, then press the ENTER button begin ripping.

- Ripping menu contain 4 button :

- Bit Rate, press Standart : 128kbps. Better Quality : 192kbps.

- Device selection, press

- Select - Unselect, Press

- Start ripping, press ENTER to start ripping process.

Note

- To return to CDDA screen, press the RETURN button again.

- When the CD ripping is in process the player will automatically begin playing.

- Only Audio CD (CD DA) discs can be ripped.

- Because the speed is 2.6x of normal speed. User is unable to play the CD DA through the rip ping process.

ENTER to change 128kbps ➔ 192kbps ➔ 128bkps.

ENTER to change between deviced (max 4).

ENTER to change from Select all or Select none.

Picture CD Playback

1. Select the desired folder.

2. Press the

Note

- Press the STOP button to return to the clips menu.

- When playing a Kodak Picture CD, the unit displays the Photo directly, not the clips menu.

Rotation

- Each time the √/® button is pressed, the picture rotates 90 degrees clockwise.

- Each time the π button is pressed, the picture rotates 180 degrees.

- Each time the † button is pressed, the picture changes to the mirror appearance.

Zoom

- Each time the ENTER Button is pressed repeteadly, the picture is enlarged. zoom mode : 100%,

125%, 150%, 200%.

π/† buttons to select a Picture file in the clips menu and then press the ENTER but-

ton.

Slide show

- When you press the ENTER/PLAY at JPEG file,it will go to full screen mode and automaically slide show.

Note

- Depending on a file size, the amount of time between each picture may be different from the manual.

- If you don’t press any button, the slide show will start automatically in about 10 seconds by default.

CD-R JPEG Disc

- Only files with the “.jpg” and “.JPG” extensions can be played.

- If the disc has not been closed during the recording phase,(ie has not been finalised) it will take longer to start playing and not all of the recorded files may be played.

- Only CD-R discs with JPEG files in ISO 9660 or Joliet format can be played.

- The name of the JPEG file may not be longer than 8 characters and should contain no blank spaces or special characters (. / = +).

- Only a consecutively written multi-se ssion disc can be played.If there is a blank segment in the multi-session disc, the disc can be played only up to the blank segment.

- A maximum of 500 images can be stored on a single CD.

- Kodak Picture CDs are recommended.

- When playing a Kodak Picture CD, only the JPEG files in the pictures folder can be played.

- Kodak Picture CD: The JPEG files in the pictures folder can be played automatically.

- Konica Picture CD: If you want to see the Picture, select the JPEG files in the clips menu.

- Fuji Picture CD: If you want to see the Picture, select the JPEG files in the clips menu.

- QSS Picture CD: The unit may not play QSS Picture CD.

- If the number of files in 1 Disc is over 500, only 500 JPEG files can be played.

- If the number of folders in 1 Disc is over 500, only JPEG files in 500 folders can be played

karaoke functions

Karaoke Functions

Operation Sequence (Only DVD-C450K, C350K)

1. Connect the Mixed Audio Out terminals with the TV or Amplifier.

2. Connect Mic into Mic jack. When a MIC is connected, the karaoke functions can be used.

Mic Volume and Key Control

1. Playback the Karaoke Disc containing the wanted songs.

- Press the KARAOKE button to select Mic Volume then press KARAOKE button again to select keycon.

2. Press the

√/® buttons to change the desired tone.

Note

- If you hear feedback (squealing or howling) while using the karaoke feature, move the micro-

phone away from the speakers or turn down the microphone volume or the speaker volume.

- When playing MP3, WMA, DTS and LPCM disc, the karaoke functions will not operate.

- When the MIC is connected, Digital Out does not work.

- The MIC sound outputs only from Analog Audio Out.

+ 22 hidden pages